Parkside PSSA 20-Li A1 Translation Of The Original Instructions

CORDLESS SABRE SAW

Translation of the original instructions

АКУМУЛАТОРЕН САБЛЕН ТРИОН

Превод на оригиналното ръководство за експлоатация

FERĂSTRĂU SABIE,

CU ACUMULATOR

Traducerea instrucţiunilor de utilizare original

ΕΠΑΝΑΦΟΡΤΙΖΟΜΕΝΗ

ΣΠΑΘΟΣΕΓΑ

Μετάφραση των αυθεντικών οδηγιών λειτουργίας

AKU SABLJASTA PILA

Prijevod originalnih uputa za uporabu

AKKU-SÄBELSÄGE

Originalbetriebsanleitung

AKU SABLJASTA TESTERA

Prevod originalnog uputstva za upotrebu

CORDLESS SABRE SAW PSSA 20-Li A1

IAN 331791_1907

GB / CY Translation of the original instructions Page 1

HR Prijevod originalnih uputa za uporabu Stranica 15

RS Prevod originalnog uputstva za upotrebu Strana 29

RO Traducerea instrucţiunilor de utilizare original Pagina 43

BG Превод на оригиналното ръководство за експлоатация Cтраница 57

GR / CY Μετάφραση των αυθεντικών οδηγιών λειτουργίας Σελίδα 73

DE / AT / CH Originalbetriebsanleitung Seite 89

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of

the device.

Prije nego što pročitate tekst, otvorite stranicu sa slikama i upoznajte se na osnovu toga sa svim funkcijama

uređaja.

Pre čitanja rasklopite obe strane sa slikama te se upoznajte sa svim funkcijama uređaja.

Înainte de a citi instrucţiunile, priviţi imaginile şi familiarizaţi-vă cu toate funcţiile aparatului.

Преди да прочетете отворете страницата с фигурите и след това се запознайте с всички функции

на уреда.

Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα με τις εικόνες και εξοικειωθείτε με όλες τις λειτουργίες

της συσκευής.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

A

All Parkside tools and the chargers PLG 20 A1/PLG 20 A2/PLG 20 A3/PDSLG 20 A1 of the

X20V Team series are compatible with the PAP 20 A1/PAP 20 A2/PAP 20 A3 battery pack.

Charging times

Charging currents

2 Ah

Battery pack

PAP 20 A1

3 Ah

Battery pack

PAP 20 A2

4 Ah

Battery pack

PAP 20 A3

max. 2.4 A

Charger PLG 20 A1

60 min

2,4 A

90 min

2,4 A

120 min

2,4 A

max. 3.5 A

Charger PLG 20 A2

60 min

2,4 A

60 min

3,5 A

80 min

3,5 A

max. 4.5 A

Charger PLG 20 A3

45 min

3,5 A

45 min

4,5 A

60 min

4,5 A

max. 4.5 A

Charger PDSLG 20 A1

35 min

3,5 A

45 min

4,5 A

60 min

4,5 A

20V max.

18V

PSSA 20-Li A1

GB

│

CY

│

1 ■

Contents

Introduction .........................................................2

Intended use .................................................................... 2

Features ........................................................................ 2

Package contents ................................................................. 2

Technical data ................................................................... 2

General power tool safety warnings .....................................3

1. Work area safety .............................................................. 3

2. Electrical safety ................................................................ 3

3. Personal safety ................................................................ 4

4. Power tool use and care ......................................................... 4

5. Battery tool use and care ........................................................ 5

6. Service ....................................................................... 5

Appliance-speciﬁc safety instructions for sabre saws. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Safety guidelines for battery chargers ................................................. 6

Original accessories/auxiliary equipment .............................................. 6

Information on saw blades ......................................................... 6

Before use ...........................................................7

Charging the battery pack (see ﬁg. A) ................................................ 7

Attaching/disconnecting the battery pack to/from the appliance ........................... 7

Checking the battery charge level .................................................... 7

Fitting/changing the saw blade ...................................................... 7

Adjusting the footplate ............................................................. 8

Adjusting the pendulum stroke ....................................................... 8

Use .................................................................8

Switching on and oﬀ .............................................................. 8

Adjusting the rotational speed ....................................................... 8

Guiding the sabre blade safely ...................................................... 8

Practical advice on sawing ......................................................... 8

Maintenance and cleaning .............................................9

Kompernass Handels GmbH warranty ..................................10

Service .............................................................11

Importer ...........................................................11

Disposal ............................................................12

Translation of the original Conformity Declaration .........................13

Ordering a replacement battery ........................................14

Telephone ordering ..............................................................14

PSSA 20-Li A1

■ 2

│

GB

│

CY

CORDLESS SABRE SAW

PSSA 20-Li A1

Introduction

Congratulations on the purchase of your new appli-

ance. You have chosen a high-quality product. The

operating instructions are part of this product. They

contain important information about safety, usage

and disposal. Before using the product, please

familiarise yourself with all operating and safety in-

structions. Use the product only as described and for

the range of applications speciﬁed. Please also pass

these operating instructions on to any future owner.

Intended use

This appliance is designed for sawing, cutting to

length and adapting wood, plastics, metal and

construction materials. The sabre saw is suitable for

rough sawing work, straight and curved cuts and

cuts oﬀ surfaces ﬂush. Heed the information con-

cerning saw blades and practical advice on sawing.

Any other uses of or modiﬁcations to the machine

are deemed to be improper usage and may result in

serious physical injury. The manufacturer accepts no

responsibility for damage(s) attributable to misuse.

This appliance is not intended for commercial use.

Features

Saw blade (SWISS MADE)

Footplate

Quick-release chuck

Pendulum stroke switch

Ventilation slits

Safety lock-out

ON/OFF switch

Handle

Battery charge level button

Battery display LED

Battery pack*

Release button for battery pack

Locking lever for footplate

Red charge control LED

Green charge control LED

High-speed charger*

Package contents

1 cordless sabre saw PSSA 20-Li A1

1 saw blade for wood BIM 152.5 mm

(SWISS MADE)

1 carrying case

1 set of operating instructions

Technical data

Cordless sabre saw PSSA 20-Li A1

Rated voltage 20 V (DC)

Rated idle stroke speed n

0

0–3000 rpm

Stroke length 20 mm

Max. cutting performance Wood 100 mm

20 mm

(in non-alloyed steel)

Sawblade mounting ½" (12.7 mm)

Battery PAP 20 A1*

Type LITHIUM ION

Rated voltage 20 V

(DC)

Capacity 2.0 Ah

Cells 5

High-speed battery charger PLG 20 A1*

INPUT

Rated voltage 230–240 V ∼, 50 Hz

(AC)

Rated power consumption 65 W

Fuse (internal) 3.15 A

T3.15A

OUTPUT

Rated voltage 21.5 V (DC)

Rated current 2.4 A

Charging time approx. 60 min

Protection class II /

(double insulation)

* BATTERY AND CHARGER ARE NOT SUPPLIED

PSSA 20-Li A1

GB

│

CY

│

3 ■

Noise emission value

Noise measurement value determined in accor-

dance with EN 62841. The A-rated noise level of

the tool is typically

Sound pressure level L

PA

= 88 dB(A)

Uncertainty K = 3 dB

Sound power level L

WA

= 99 dB(A)

Uncertainty K = 3 dB

Wear hearing protection!

Vibration values (vector total of three directions)

determined in accordance with EN 62841:

Total vibration value

Sawing chipboard a

h,B

= 11.4 m/s

2

Uncertainty K = 1.5 m/s

2

Sawing of timber beams a

h,WB

= 9.6 m/s

2

Uncertainty K = 1.5 m/s

2

NOTE

► The vibration emission values and the noise

emission values given in these instructions

have been measured in accordance with

a standardised test procedure and can be

used for comparison of the power tool with

another tool.

► The speciﬁed total vibration values and the

noise emission values can also be used to

make a provisional load estimate.

WARNING!

► Depending on the manner in which the

power tool is being used, and in particular

the kind of workpiece that is being worked,

the vibration and noise emission values can

deviate from the values given in these instruc-

tions during actual use of the power tool.

► Try to keep the load as low as possible.

Measures to reduce the vibration load are,

e.g. wearing gloves and limiting the working

time. Wherein all states of operation must be

included (e.g. times when the power tool is

switched oﬀ and times where the power tool

is switched on but running without load).

General power tool

safety warnings

WARNING!

► Read all safety warnings, instructions, illust-

rations and speciﬁcations provided with this

power tool. Failure to follow all instructions

listed below may result in electric shock, ﬁre

and/or serious injury.

Save all warnings and instructions for future

reference.

The term „power tool“ in the warnings refers to

your mains-operated (corded) power tool or bat-

tery-operated (cordless) power tool.

1. Work area safety

a) Keep work area clean and well lit. Cluttered

or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or

fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

2. Electrical safety

a) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded)

power tools. Unmodiﬁed plugs and matching

outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or ground-

ed surfaces, such as pipes, radiators, ranges

and refrigerators. There is an increased risk of

electric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

PSSA 20-Li A1

■ 4

│

GB

│

CY

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduc-

es the risk of electric shock.

3. Personal safety

a) Stay alert, watch what you are doing and

use common sense when operating a power

tool. Do not use a power tool while you are

tired or under the inﬂuence of drugs, alcohol

or medication. A moment of inattention while

operating power tools may result in serious

personal injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such

as a dust mask, non-skid safety shoes, hard hat or

hearing protection used for appropriate conditions

will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools

with your ﬁnger on the switch or energising

power tools that have the switch on invites

accidents.

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool

may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away

from moving parts. Loose clothes, jewellery or

long hair can be caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used.

Use of dust collection can reduce dust-related

hazards.

h) Do not let familiarity gained from frequent

use of tools allow you to become complacent

and ignore tool safety principles. A careless

action can cause severe injury within a fraction

of a second.

4. Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at

the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and oﬀ. Any power tool that can-

not be controlled with the switch is dangerous

and must be repaired.

c) Disconnect the plug from the power source

and/or remove the battery pack, if detacha-

ble, from the power tool before making any

adjustments, changing accessories, or storing

power tools. Such preventive safety measures

reduce the risk of starting the power tool acci-

dentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition

that may aﬀect the power tool’s operation. If

damaged, have the power tool repaired be-

fore use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-

ing into account the working conditions and

the work to be performed. Use of the power

tool for operations diﬀerent from those intended

could result in a hazardous situation.

PSSA 20-Li A1

GB

│

CY

│

5 ■

h) Keep handles and grasping surfaces dry,

clean and free from oil and grease. Slippery

handles and grasping surfaces do not allow

for safe handling and control of the tool in unex-

pected situations.

5. Battery tool use and care

a) Recharge only with the charger speciﬁed by

the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of

ﬁre when used with another battery pack.

b) Use power tools only with speciﬁcally desig-

nated battery packs. Use of any other battery

packs may create a risk of injury and ﬁre.

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from

one terminal to another. Shorting the battery

terminals together may cause burns or a ﬁre.

d) Under abusive conditions, liquid may be ejec-

ted from the battery; avoid contact. If contact

accidentally occurs, ﬂush with water. If liquid

contacts eyes, additionally seek medical

help. Liquid ejected from the battery may cause

irritation or burns.

e) Do not use a battery pack or tool that is

damaged or modiﬁed. Damaged or modiﬁed

batteries may exhibit unpredictable behaviour

resulting in ﬁre, explosion or risk of injury.

f) Do not expose a battery pack or tool to ﬁre

or excessive temperature. Exposure to ﬁre

or temperature above 130 °C (265°F) may

cause explosion.

g) Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range speciﬁed in the instruc-

tions. Charging improperly or at temperatures

outside the speciﬁed range may damage the

battery and increase the risk of ﬁre.

CAUTION! RISK OF EXPLOSION!

Never charge non-rechargeable

batteries!

Protect the rechargeable battery from

heat, for example from continuous

exposure to sunlight, ﬁre, water and

moisture. There is a risk of explosion.

6. Service

a) Have your power tool serviced by a qualiﬁed

repair person using only identical replace-

ment parts. This will ensure that the safety of

the power tool is maintained.

b) Never service damaged battery packs. Service

of battery packs should only be performed by

the manufacturer or authorized service providers.

Appliance-speciﬁc safety instructions

for sabre saws

To avoid the risk of injury or ﬁre as well as

health risks:

■ Hold the power tool by the insulated

gripping surfaces when performing work

where the power tool may hit hidden pow-

er lines or its own power cord. Contact with

a live wire may electrify exposed metal parts of

the power tool and could give the operator an

electric shock.

■ Secure and secure the workpiece to a

stable surface by means of clamps or

otherwise. Holding the workpiece by hand or

against your body will cause it to remain unsta-

ble, resulting in loss of control.

■ Wear a dust mask!

PSSA 20-Li A1

■ 6

│

GB

│

CY

Safety guidelines for battery chargers

■ This appliance may be used by

children aged 8 years and above

and by persons with limited physical,

sensory or mental capabilities or

lack of experience and knowledge,

provided that they are under super-

vision or have been told how to use

the appliance safely and are aware

of the potential risks. Do not allow

children to use the appliance as a

toy. Cleaning and user maintenance

tasks may not be carried out by

children unless they are supervised.

■ To avoid potential risks, damaged

mains cables should be replaced

by the manufacturer, their customer

service department or a similarly

qualiﬁed person.

The charger is suitable for indoor use

only.

WARNING!

■ If the power cord requires replacement, this

should be carried out by the manufacturer or

an approved representative to avoid safety

hazards.

CAUTION!

♦ This charger can only charge the following

batteries: PAP 20 A1/PAP 20 A2/

PAP 20 A3.

♦ A current list of battery compatibility can be

found at www.lidl.de/Akku.

Original accessories/auxiliary

equipment

■ Use only the accessories and additional

equipment that are speciﬁed in the oper-

ating instructions and are compatible with

the appliance. Using attachments or accessory

tools other than those recommended in the oper-

ating instructions can lead to a risk of injury.

Information on saw blades

You can use any saw blade provided it is ﬁtted with

a suitable mount – ½" (12.7 mm) universal shaft.

Saw blades optimised for your sabre saw are

available from retail stores in diﬀerent lengths for

various purposes.

NOTE

► TPI = teeth per inch = the number of teeth

per 2.54 cm

Wood saw blade:

Dimensions: 152.5 x 0.9 mm, 6 - 12 TPI

Ideal for: sawing construction wood, chipboard,

panels and plywood, and also plunge cuts.

PSSA 20-Li A1

GB

│

CY

│

7 ■

Before use

Charging the battery pack (see ﬁg. A)

CAUTION!

► Always unplug the appliance before you

remove the battery pack from or connect the

battery pack to the charger.

NOTE

► Never charge the battery pack if the ambient

temperature is below 10°C or above 40°C.

If a lithium-ion battery is to be stored for an

extended period, the charge level should be

checked regularly. The optimum charge level is

between 50% and 80%. The storage climate

should be cool and dry and the ambient tem-

perature should be between 0°C and 50°C.

♦ Connect the battery pack

to the high-speed

battery charger (see ﬁg. A).

♦ Insert the power plug into the socket.

The control LED

lights up red.

♦ The green LED

indicates that the charging

process is complete and the battery pack is

ready.

CAUTION!

♦ If the red control LED

ﬂashes, this means

that the battery pack has overheated and

cannot be charged.

♦ If the red and green control LEDs

both

ﬂash, this means that the battery pack is

defective.

♦ Push the battery pack

into the appliance.

♦ Switch oﬀ the charger

for at least 15 minutes

between successive charging sessions.

Also disconnect the power plug from the mains

power socket.

Attaching/disconnecting the battery

pack to/from the appliance

Inserting the battery pack:

♦ Allow the battery pack

to click into place in

the appliance.

Removing the battery pack:

♦ Press the release button

and remove the

battery pack .

Checking the battery charge level

♦ Press the battery charge level button to check

the status of the battery (see also main diagram).

The status will be shown on the battery display

LED as follows:

RED/ORANGE/GREEN = maximum charge

RED/ORANGE = medium charge

RED = low charge – charge the battery

Fitting/changing the saw blade

WARNING!

► Remove the battery before carrying out

any work on the power tool (e.g. mainte-

nance, changing tools, etc.) as well as during

the transport and storage of the power tool.

Unintentional activation of the ON/OFF

switch can result in injury.

♦ Turn the quick-release chuck

as far as the

stop and hold it in this position.

♦ Push the required saw blade

into the

quick-release chuck as far as the stop.

CAUTION!

► The teeth of the saw blade

must point

downwards!

PSSA 20-Li A1

■ 8

│

GB

│

CY

♦ Let go of the quick-release chuck so that it

returns to its initial position. The saw blade

is now locked.

Adjusting the footplate

RISK OF INJURY!

► Always switch the appliance oﬀ and remove

the battery before carrying out any work on

the appliance.

♦ Adjust the footplate

according to the cutting

depth.

♦ To do so, undo the locking lever

and move

the footplate to the corresponding position.

♦ Lock this position by closing the locking lever

.

Adjusting the pendulum stroke

♦ You can use the pendulum stroke switch

to adjust the pendular movement of the saw

blade . You can achieve ﬁne, clean-cut edges

without pendulum movement (setting "0").

Deactivate pendulum movement when working

on thin workpieces. You can achieve an increas-

ingly fast work rate if the pendulum stroke is

activated (setting "I").

Use

Switching on and oﬀ

Switching on:

♦ First press the safety lock-out

and then the

ON/OFF switch

. Afterwards, release the

safety lock-out .

Switching oﬀ:

♦ Release the ON/OFF switch

.

Adjusting the rotational speed

Press the ON/OFF switch lightly for a low speed.

Increasing the pressure increases the speed.

NOTE

► The integrated motor brake ensures rapid

stoppage.

Guiding the sabre blade safely

To adapt to the workpiece and for safe placement,

the footplate can be swivelled. It must always be

in contact with the workpiece when the appliance

is running.

Practical advice on sawing

♦ Check the material to be worked to make sure

that all foreign objects have been removed,

e.g. nails, screws, etc.

♦ Ensure that the ventilation slits

are not

covered.

♦ Switch the appliance on before moving it

towards the material to be worked.

♦ Switch the appliance oﬀ immediately if the saw

blade

jams.

Open up the sawn gap using a suitable tool

and pull out the sabre saw.

■ Use the appropriate saw blade

and stroke

rate for the material to be worked.

■ Saw blades optimised for your sabre saw are

available from retail stores in diﬀerent lengths

for various purposes.

■ Saw the material at a constant speed.

PSSA 20-Li A1

GB

│

CY

│

9 ■

Sawing ﬂush to edges:

Using ﬂexible saw blades with a suitable cor-

responding length, you can saw oﬀ protruding

workpieces such as pipes ﬂush to the wall.

Proceed as follows:

1. Place the saw blade

directly against the wall.

2. Bend it by applying lateral pressure to the sabre

saw so that the footplate makes contact with

the wall.

3. Switch the appliance on as described and

saw oﬀ the work piece by applying constant

pressure.

Plunge sawing:

CAUTION! RISK OF KICKBACK!

■ Plunge cuts may only be made in soft

materials (wood or similar).

Proceed as follows:

1. Place the sabre saw with the lower edge of the

footplate onto the workpiece. Switch the

appliance on.

2. Tilt the sabre saw forwards and plunge the saw

blade

into the workpiece.

3. Position the sabre saw vertically and continue

sawing along the cutting line.

Maintenance and cleaning

WARNING! RISK OF INJURY!

Always switch the appliance oﬀ and

remove the battery before carrying

out any work on the appliance.

■ The appliance must always be kept clean, dry

and free from oil or grease.

■ Use a soft, dry cloth to clean the housing.

■ Replace the saw blade as soon as its teeth are

blunt and proper sawing is therefore no longer

possible.

■ Keep the appliance and ventilation slits clean at

all times. If the ventilation slits are blocked, there

is a risk of overheating and/or the appliance

being damaged.

■ Always clean the appliance after completion

of work.

■ Never permit liquids to enter inside the appli-

ance. Use a cloth to clean the housing. Never

use petrol, solvents or cleansers which can

damage plastic.

■ If necessary, clean the saw blade mount with a

brush or compressed air.

■ If a lithium-ion battery is to be stored for an

extended period, the charge level should be

checked regularly. The optimum charge level is

between 50% and 80%. The optimum storage

environment is cool and dry.

WARNING!

► Do not use any accessories not recommend-

ed by PARKSIDE. This can lead to electric

shock and ﬁre.

PSSA 20-Li A1

■ 10

│

GB

│

CY

Kompernass Handels GmbH

warranty

Dear Customer,

This appliance has a 3-year warranty valid from

the date of purchase. If this product has any faults,

you, the buyer, have certain statutory rights. Your

statutory rights are not restricted in any way by the

warranty described below.

Warranty conditions

The warranty period starts on the date of purchase.

Please keep your receipt in a safe place. This will

be required as proof of purchase.

If any material or manufacturing fault occurs within

three years of the date of purchase of the product,

we will either repair or replace the product for you

or refund the purchase price (at our discretion).

This warranty service requires that you present the

defective appliance and the proof of purchase (re-

ceipt) within the three-year warranty period, along

with a brief written description of the fault and of

when it occurred.

If the defect is covered by the warranty, your prod-

uct will either be repaired or replaced by us. The

repair or replacement of a product does not signify

the beginning of a new warranty period.

Warranty period and statutory claims for

defects

The warranty period is not prolonged by repairs

eﬀected under the warranty. This also applies to

replaced and repaired components. Any damage

and defects present at the time of purchase must

be reported immediately after unpacking. Repairs

carried out after expiry of the warranty period shall

be subject to a fee.

Scope of the warranty

This appliance has been manufactured in accord-

ance with strict quality guidelines and inspected

meticulously prior to delivery.

The warranty covers material faults or production

faults. The warranty does not extend to product

parts subject to normal wear and tear or to fragile

parts which could be considered as consumable

parts such as switches, batteries or parts made of

glass.

The warranty does not apply if the product has

been damaged, improperly used or improper-

ly maintained. The directions in the operating

instructions for the product regarding proper use

of the product are to be strictly followed. Uses

and actions that are discouraged in the operating

instructions or which are warned against must be

avoided.

This product is intended solely for private use and

not for commercial purposes. The warranty shall

be deemed void in cases of misuse or improper

handling, use of force and modiﬁcations / repairs

which have not been carried out by one of our

authorised Service centres.

The warranty period does

not apply to

■ Normal reduction of the battery capacity

overtime

■ Commercial use of the product

■ Damage to or alteration of the product by the

customer

■ Non-compliance with safety and maintenance

instructions, operating errors

■ Damage caused by natural hazards

PSSA 20-Li A1

GB

│

CY

│

11 ■

Warranty claim procedure

To ensure quick processing of your case, please

observe the following instructions:

■ Please have the till receipt and the item number

(e.g.IAN12345) available as proof of purchase.

■ You will ﬁnd the item number on the type plate

on the product, an engraving on the product,

on the front page of the operating instructions

(below left) or on the sticker on the rear or

bottom of the product.

■ If functional or other defects occur, please

contact the service department listed either by

telephone or by e-mail.

■ You can return a defective product to us free of

charge to the service address that will be pro-

vided to you. Ensure that you enclose the proof

of purchase (till receipt) and information about

what the defect is and when it occurred.

You can download these instructions

along with many other manuals,

product videos and installation

software at www.lidl-service.com.

This QR code will take you directly

to the Lidl service page (www.lidl-service.com)

where you can open your operating instructions by

entering the item number (IAN) 123456.

Service

WARNING!

► Have the power tool repaired by the service

centre or a qualiﬁed electrician and only

using genuine replacement parts. This will

ensure that the safety of the appliance is

maintained.

► If the mains cable is damaged, it must be

replaced with a special cable that is avail-

able from the manufacturer or its customer

service.

NOTE

► Replacement parts not listed (such as carbon

brushes, switch) can be ordered via our

service hotline.

Service Great Britain

Tel.: 0800 404 7657

E-Mail: [email protected]

CY

Service Cyprus

Tel.: 8009 4409

E-Mail: [email protected]

IAN 331791_1907

Importer

Please note that the following address is not the

service address. Please use the service address

provided in the operating instructions.

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

GERMANY

www.kompernass.com

PSSA 20-Li A1

■ 12

│

GB

│

CY

Disposal

The packaging is made from

environmentally-friendly material and

can be disposed of at your local

recycling plant.

Do not dispose of power tools

in your normal domestic waste!

European Directive 2012/19/EU

requires that worn-out power tools be

collected separately and recycled in

an environmentally compatible manner.

Do not dispose of batteries in

your normal household waste!

Defective or worn-out rechargeable

batteries must be recycled according

to Directive 2006/66/EC. Take the

battery pack and/or appliance to a nearby collec-

tion facility.

Please consult your local authorities regarding

suitable disposal of worn out power tools/battery

packs.

Note the labelling on the packaging

and separate the packaging material

components for disposal if necessary.

The packaging material is labelled

with abbreviations (a) and numbers (b) with the

following meanings: 1–7: Plastics, 20–22: Paper

and cardboard, 80–98: Composites.

Your local community or municipal

authorities can provide information on

how to dispose of the worn-out

product.

PSSA 20-Li A1

GB

│

CY

│

13 ■

Translation of the original Conformity Declaration

We, KOMPERNASS HANDELS GMBH, document oﬃcer: Mr. Semi Uguzlu, BURGSTR. 21,

44867 BOCHUM, GERMANY, hereby declare that this product complies with the following

standards, normative documents and EC directives:

Machinery Directive

(2006/42/EC)

EC Low Voltage Directive

(2014/35 / EU, charger only)

EMC (Electromagnetic Compatibility)

(2014/30/EU)

RoHS Directive

(2011/65/EU)*

* The manufacturer bears the full responsibility for compliance with this conformity declaration. The object of the dec-

laration described above complies with the requirements of the Directive 2011/65/EU of the European Parliament

and Council of 8 June 2011 on the limitations of use of certain dangerous substances in electrical and electronic

appliances.

Applied harmonised standards:

EN 62841-1:2015

EN 62841-2-11:2016

EN 62233:2008

EN 60335-1:2012/A13:2017

EN 60335-2-29:2004/A2:2010

EN 55014-1:2017

EN 55014-2:2015

EN 61000-3-2:2014

EN 61000-3-3:2013

EN 50581:2012

Type designation of machine: Cordless sabre saw PSSA 20-Li A1

Year of manufacture: 11 - 2019

Serial number: IAN 331791_1907

Bochum, 20/11/2019

Semi Uguzlu

- Quality Manager -

We reserve the right to make technical changes in the context of further product development.

PSSA 20-Li A1

■ 14

│

GB

│

CY

Ordering a replacement battery

If you want to order a replacement battery for your appliance, you can do so easily via the Internet on

www.kompernass.com or by telephone.

NOTE

► Online ordering of replacement parts might not be possible in some countries. In this is the case,

please contact the Service hotline.

Telephone ordering

Service Great Britain

Tel.: 0800 404 7657

E-Mail: [email protected]

CY

Service Cyprus

Tel.: 8009 4409

E-Mail: [email protected]

To ensure fast processing of your order, have the article number of your appliance to hand

(e.g. IAN 331791) in case of questions. The article number can be found on the type plate

or the title page of these instructions.

PSSA 20-Li A1

HR

│

15 ■

Sadržaj

Uvod ..........................................................16

Namjenska uporaba ........................................................ 16

Oprema .................................................................. 16

Opseg isporuke ............................................................ 16

Tehnički podaci ............................................................16

Opće sigurnosne napomene za uporabu električnog alata ..............17

1. Sigurnost na radnom mjestu .................................................17

2. Električna sigurnost. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3. Sigurnost osoba .......................................................... 18

4. Korištenje i rukovanje električnim alatom .......................................18

5. Korištenje i rukovanje baterijskim alatom ....................................... 19

6. Servis ..................................................................20

Sigurnosne napomene speciﬁčne za sabljaste pile ................................. 20

Sigurnosne napomene za punjače .............................................. 20

Originalni pribor / dodatni uređaji .............................................21

Informacije o listovima pile ....................................................21

Prije uključivanja uređaja .........................................21

Punjenje paketa baterije (vidi sliku A). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Umetanje / vađenje paketa baterija iz uređaja ....................................22

Provjera stanja baterije .......................................................22

Montiranje / zamjena lista pile ................................................22

Podešavanje osnovne ploče ...................................................22

Postavljanje progresivnog hoda ................................................22

Puštanje u rad ...................................................22

Uključivanje i isključivanje .................................................... 22

Postavljanje broja okretaja ....................................................23

Sigurno vođenje sabljaste pile ................................................. 23

Napomene u vezi piljenja .................................................... 23

Održavanje i čišćenje .............................................24

Jamstvo tvrtke Kompernass Handels GmbH ..........................24

Servis ..........................................................26

Uvoznik ........................................................26

Zbrinjavanje ....................................................26

Prijevod originalne izjave o sukladnosti .............................27

Narudžba zamjenske baterije .....................................28

Telefonska narudžba ........................................................28

PSSA 20-Li A1

■ 16

│

HR

BATERIJSKA SABLJASTA

PILA PSSA 20-Li A1

Uvod

Čestitamo na kupnji Vašeg novog uređaja. Time

ste se odlučili za vrlo kvalitetan proizvod. Upute

za uporabu dio su opreme ovog proizvoda. One

sadrže važne napomene za sigurnost, rukovanje i

zbrinjavanje. Prije uporabe proizvoda upoznajte se

sa svim napomenama za rukovanje i svim sigurno-

snim napomenama. Proizvod koristite isključivo na

opisani način i u navedenim područjima uporabe.

U slučaju predaje proizvoda trećim osobama pre-

dajte i svu dokumentaciju.

Namjenska uporaba

Uređaj je namijenjen za piljenje, skraćivanje i prila-

gođavanje drveta, plastike, metala ili građevinskih

materijala sa čvrstim uporištem. Sabljasta pila je

prikladna za grube radove piljenja, ravne i za-

krivljene rezove i ravno rezanje površina. Obratite

pozornost na informacije o listovima pile i radne

napomene za piljenje. Svaki drugi način uporabe,

te svaka izmjena uređaja smatra se nenamjenskom

i krije znatnu opasnost od nezgoda. Proizvođač ne

preuzima odgovornost za štete nastale nenamjen-

skim korištenjem uređaja. Uređaj nije namijenjen za

komercijalnu uporabu.

Oprema

List pile (SWISS MADE)

Donja ploča

Čeljust za brzo zatezanje

Prekidač progresivnog hoda

Ventilacijski otvori

Blokada uključivanja

Prekidač UKLJ / ISKLJ

Ručka

Tipka za stanje baterije

LED indikator baterije

Paket baterija*

Tipka za deblokadu paketa baterija

Poluga za ﬁksiranje osnovne ploče

Crveni LED indikator za kontrolu punjenja

Zeleni LED indikator za kontrolu punjenja

Brzi punjač*

Opseg isporuke

1 Baterijska sabljasta pila PSSA 20-Li A1

1 Rezni list za drvo BIM 152,5 mm (SWISS MADE)

1 Kovčeg za nošenje

1 Upute za uporabu

Tehnički podaci

Baterijska sabljasta pila: PSSA 20-Li A1

Nazivni napon: 20 V

(istosmjerna

struja)

Broj uboda u praznom

hodu:

n

0

0 - 3000 min

-1

Dužina hoda: 20 mm

Maks. učinak rezanja: Drvo 100 mm

20 mm

(u nelegiranom čeliku)

Prihvat reznog lista:

1

/

2

“ (12,7 mm)

Baterija: PAP 20 A1*

Tip: LITIJ-IONSKA

Nazivni napon: 20 V

(istosmjerna

struja)

Kapacitet: 2,0 Ah

Broj ćelija: 5

Brzi punjač baterija: PLG 20 A1*

ULAZ / Input:

Nazivni napon: 230 - 240 V

~

, 50 Hz

(izmjenična struja)

Nazivna snaga: 65 W

Osigurač (unutarnji): 3,15 A

T3.15A

IZLAZ / Output:

Nazivni napon: 21,5 V

(istosmjerna

struja)

Nazivna struja: 2,4 A

Trajanje punjenja: otpr. 60 min

Razred zaštite: II /

(dvostruka izolacija)

* BATERIJA I PUNJAČ NISU SADRŽANI U

OPSEGU ISPORUKE

OPREZ

UPOZORENJE: Mogućnost strujnog udara!

Ne otvarati kućište proizvoda!

Pagina se încarcă ...

Parkside PSSA 20-Li A1 Translation Of The Original Instructions

Acest manual este potrivit și pentru

Parkside PSSA 20-Li A1 Translation Of The Original Instructions

Lucrări conexe

Alte documente