Ferm GRM1015 Manual de utilizare

Marca: Ferm

Model: GRM1015

Categorie: Curatatoare de inalta presiune

Tip: Manual de utilizare

WWW.FERM.COM

Original instructions 04

GRM1015

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Fig. 5

HIGH PRESSURE CLEANER

The numbers in the text refer to the diagrams

on pages 2-3.

For your own safety and that of others,

we recommend that you read this

instruction manual carefully before using

this machine. Keep this instruction

manual and the documentation provided

with the machine for future reference.

Introduction

The high pressure cleaner GRM1015 is quick and

efficient for cleaning vehicles, machines, boats,

buildings, etc., by the removal of stubborn dirt

using clean water and chemical detergents.

When using chemical detergents, only use

biodegradable types. Only clean vehicle engines

in areas in which suitable oil traps are installed.

Contents

1. Machine information

2. Safety instructions

3. Assembly

4. Use

5. Service & maintenance

1. MACHINE INFORMATION

Technical specifications

Voltage 230 V~ /50Hz

Input power 1850 W

Max. pressure water supply 4 bar

Allowable pressure 135 bar

Max. water temperature 50º C

Max. working flow rate 6.9 l/min

Hose length 5 m

Weight 11 kg

IP class IPX5

LPA(sound pressure) 77.1 dB(A),

K=3 dB(A)

LWA(acoustic power) 90.5 dB(A)

Vibration value <2.5m/s2

Contents of packing

1 High pressure cleaner

1 Hose

1 Trigger

1 Lance holder (2 pcs.)

1 Hose handle + screws

1 Lance extension

1 Lance adjustable nozzle

1 Detergent bottle (built in)

1 Safety and operating instructions

1 Warranty card

Check the appliance, any loose parts and

accessories for damage caused during transport.

Product information

Fig. 1

1. High pressure washer

2. On/off switch

3. Water inlet

4. wheel

5. Water outlet

6. Gun holder

7. Handle

8. Hose hook

9. Spray gun

10. Adjustable Spray Wand

11. Hose connector

2. SAFETY INSTRUCTIONS

Explanation of the symbols

Denotes risk of personal injury, loss of life

or damage to the tool in case of non-

observance of the instructions in this

manual.

Indicates electrical shock hazard.

DO NOT direct the water jet

towards people or animals.DO NOT

direct the water jet towards the unit

itself, electrical parts or towards

other electrical

The machine is not intended to be

connected to the potable water mains.

Safety instructions

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of fire, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions.

Electrical safety

• Always check if your mains voltage

corresponds with the value on the type plate.

• When replacing old cables or plugs:

• Throw away old cables or plugs immediately

as soon as new ones have replaced these. It is

dangerous to put the plug of a loose cable into

the socket outlet.

• When using extension cables:

• Only use an approved extension cable that is

suitable for the machine’s power. The cores

must have a diameter of at least 1.5 mm

When the extension cable is on a reel, unroll

the cable in its entirety.

• All electrical connections e.g. extension

cable, must be of an approved waterproof

type for outdoor use and marked accordingly.

Extension cables must be threecore, one of

which is EARTH.

Immediately switch off the machine when:

• Interruption of the mains plug, mains lead or

mains lead damage.

• Defect switch

• Smoke or stench of scorched isolation

Specific safety rules

The USE and MAINTENANCE manual constitutes

an essential part of the cleaner equipment and

should be kept in a safe place for future reference.

If you sell the cleaner, the manual should be

handed on to the new owner.

• Before starting the cleaner, make sure that

it is receiving water correctly. Operating the

cleaner without water could damage the seals.

• Do not disconnect the plug by pulling on the

electrical cable.

• If you are too far from the object you wish

to clean, do not move the cleaner nearer by

pulling on the high pressure hose; use the

handle provided.

• In versions not equipped with TSS device,

do not operate the cleaner for more than 1-2

minutes with the gun closed as this could

damage the seals.

• Protect the cleaner from freezing during the

winter.

• Do not obstruct the ventilation grilles during

operation.

• The cross-section of any extension cables

used must be proportional to their length, i.e.

the longer the extension cable, the greater the

cross-section; cables with a protection level of

“IPX5” must be used.

• Position the cleaner AS NEAR POSSIBLE to

the water supply.

• The packaging is easily recyclable, and must be

disposed of in compliance with the regulations

in force in the country of installation.

• Use the cleaner only with accessories

and replacement parts authorized by the

manufacturer. The use of original accessories

and replacement parts will ensure safe,

trouble-free operation.

• The cleaner must be used standing on a

secure, stable surface.

• Avoid unintentional firing of the trigger. Do not

carry the lance/ trigger assembly with your

hand over the trigger. Always use the trigger

lock mechanism.

• Ensure that the safety lock on the trigger

is used, when you have stopped using

the pressure washer to prevent accidental

operation. (fig 5)

• Read all the instructions before using the

machine.

• Machines shall not be used by children.

Children should be supervised to ensure

that they do not play with the machine. This

machine is not intended for use by persons

(including children) with reduced physical,

sensory or mental capabilities, or lack of

experience and knowledge

• The electrical supply connection shall be made

by a qualified person and comply with IEC

60364-1. The electric supply to this machine

should include either a residual current device

that will interrupt the supply if the leakage

current to earth exceeds 30 mA for 30 ms or a

device that will prove the earth circuit.

• The machine is intended to be used at

a temperature above o degree. (Only for

machine with power cord of H05VV-F).

• The operating method to be followed in the

event of accident (e.g. contact with detergents:

rinse with an abundance of clean water) or

breakdown to prevent unsafe situations.

• This machine has been designed for use with

the cleaning agent supplied or recommended

by the manufacturer. The use of other cleaning

agents or chemicals may adversely affect the

safety of the machine.

• Recommend the operator to wear ear

protectors.

• Do not use the machine within range of

persons unless they wear protective clothing.

• Do not direct the jet against yourself or others

in order to clean clothes or foot-wear.

• Risk of explosion-Do not spray flammable

liquids.

• High pressure hoses, fittings and couplings

are important for the safety of the machine.

Use only hosed, fittings and couplings

recommended by the manufacturer.

• To ensure machine safety, use only original

spare parts from the manufacturer or approved

by the manufacturer.

• Water that has flown through backflow

preventers is considered to the non-potable.

• The machine shall be disconnected from its

power source by removing the plug from the

socket-outlet during cleaning or maintenance

and when replacing the machine to another

function.

• Observe a distance of at least 30cm when

using the jet to clean painted surfaces to avoid

damaging paintwork.

• Do not use the machine if a supply cord or

important parts of the machine are damaged,

e.g. safety devices, high pressure hoses,

trigger gun.

• If an extension cord is used, the plug and

socket must be of watertight construction.

• Inadequate extension cords can be dangerous.

If an extension cord is used, it shall be suitable

for outdoor use, and the connection has to be

kept dry and off the ground. It is recommended

that this is accomplished by means of a cord

reel which keeps the socket at least 60mm

above the ground.

• In order to avoid a hazard due to inadvertent

resetting of the thermal cut-out, this

appliance must not be supplied through an

external switching device, such as a timer,

or connected to a circuit that is regularly

switched on and off by the utility.

• To ensure the machine safety, please only

use original spare parts (including nozzle)

from the manufacturer or approved by the

manufacturer. Do not use the machine before

you changed them if they are damaged.

• Be care of the danger of the kickback force on

the spray assembly when opening the trigger

gun and grasp the gun with hands firmly.

• To reduce the risk of injury, close supervision

is necessary when a machine is used near

children. High-pressure cleaner shall not be

used by children or untrained person.

• Know how to stop the machine and bleed

pressures quickly. Be thoroughly familiar with

the controls.

• Stay alert and watch what you are doing.

• Do not operate the machine when fatigued or

under the influence of alcohol or drugs.

• Keep operating area clear of all persons.

• Do not overreach or stand on unstable

support. Keep good footing and balance at all

times.

• Follow the maintenance instructions specified

in the manual.

• This machine must be grounded. If it has

malfunction or breakdown, grounding provides

a path of least resistance for electric current

to reduce the risk of electric shock. The

plug must be plugged into an appropriate

outlet that is properly installed and grounded

in accordance with all local codes and

ordinances. The rating voltage (V/Hz) of the

machine has to be in compliance with the local

power supplying voltage.

• Check with a qualified electrician or service

personnel if you are in doubt as to whether the

outlet is properly grounded. Do not modify the

plug provided with the machine. If it will not

fit the outlet, have a proper outlet installed by

a qualified electrician. Do not use any type of

adapter with this machine.

• Use only 3-wire extension cords that have

3-prong grounding-type plugs and 3-pole

cord connectors that accept the plug from

the machine. Use only extension cords that

are intended for outdoor use and the socket

must be of watertight construction. These

extension cords are identified by a marking

“Acceptable for use with outdoor machines;

store indoors while not in use.” Use only

extension cords having an electrical rating

not less than the rating of the machine. Do

not use damaged extension cords. Examine

extension cord before using and replace if

damaged. Inadequate extension cords can

be dangerous. Do not abuse extension cord

and do not yank on any cord to disconnect.

Keep cord away from heat and sharp edges.

Always disconnect the extension cord from the

receptacle before disconnecting the machine

from the extension cord.

• To reduce the risk of electrocution, don’t start

and run the machine in the rain or storm. Keep

all connections dry and off the ground. Do

not touch plug with wet hands. It is strictly

prohibited to let water leak into the machine.

• When the machine is turned on, the interior

pumps start and continue to run even if

the pressure wand trigger has not been

depressed. Running the machine for more than

3 minutes without depressing the pressure

wand trigger could cause heat damage to the

motor and pumps, Please do not leave the

machine running unattended or unused for

more than 3 minutes.

• When the machine is running, please maintain

a constant water supply. Without water

circulation will damage the sealing rings of the

machine.

• It is necessary to turn on the spray lance within

one or two minutes after the machine has been

started. Otherwise, the temperature of the

circulating water within the machine will soon

rise to a critical point, which will cause damage

to the sealing rings inside the machine.

• Don’t start and run the machine in a place

excessively cold so as to prevent the machine

from the freezing current.

• This machine has been designed for only

using cleaning water, do not use corrosive

chemicals.

• Use cleaning agent supplied or recommend by

the manufacturer.

• High-pressure jets can be dangerous if subject

to misuse. The jet must not be directed at

persons, animals, live electrical equipment or

the machine itself. Pressure washers should

not be pointed at tire walls, as it may be

possible to damage them.

• Do not direct the jet against yourself or others

in order to clean clothes or footwear.

• Disconnect from the electrical power supply

before carrying out user maintenance.

• If the mains cable is damaged it must be

replaced by the manufacturer, or its service

agent or similarly qualified person to avoid a

hazard.

• Do not use the machine if a supply cord or

important parts are damaged, e.g. safety

devices, high pressure hoses, trigger gun.

• Be aware of the recoil caused by the water jet

when the machine is switched on.

• When the machine is moving and installing,

the machine must be in flat. When moving the

machine, pulling the handle to move it.

• Connect to the water supply. The machines are

not suitable for connection to portable water

mains. Connect the machine to the water

supply. (It can be a water container).

• Make sure the inlet water pressure keeps

between 0.01MPa and 0.4MPa.The inlet pipe

should at least 5 M long. Do not use the pipe if

the pipe is damaged. If you want connect this

machine to portable water mains, you must

install a backflow preventer in the water pipe

to prevent dirty water flow back to the drinking

water system. The backflow preventer shall

comply with EN 60335-2-79 ANNEX AA.

3. ASSEMBLY AND USE

The motor of this pressure washer will

NOT run. It will only operate when the

trigger is squeezed.

• Connect the outlet hose to the washer and

connect the spray gun to the outlet hose.

• Connect nozzle and nozzle extension.

• Check gauze filter is clear of any blockage.

• Connect the water supply hose.

• Check that the hose has no kinks in it.

• Turn on water and check for leaks.

• Depress trigger to allow air to be expelled

though the pump and hoses, lock trigger.

• Plug in machine and turn on switch.

• Unlock trigger and use the pressure washer.

Shut down

1. Turn off the motor(push switch to the off

position).

2. Unplug the unit from the power source.

3. Turn off the water supply.

4. Press the trigger of the gun to depressurize the

system.

5. Disconnect the garden hose from the pressure

washer.

6. Wipe all surfaces of the unit with a damp clean

cloth.

7. Engage the gun safety lock.

CAUTION: ALWAYS turn off the unit’s motor

BEFORE turning off the unit’s water supply.

Serious damage could occur to the motor if the

unit is run without water.

CAUTION: NEVER disconnect the high-pressure

discharge hose from the machine while the

system is still pressurized. To depressurize the

unit, turn off the motor, turn off the water supply

and squeeze the trigger 2-3 times

Water supply

• Ensure that you have a suitable water supply

to feed the pressure washer. Check that all

connections are tight and there are no leaks in

the hose.

• The supply tap should be fully open (do not

turn on the pressure washer yet).

• Now depress the trigger (unlock trigger lock

first) to let water pass through the unit and

expel any air.

Warning! This unit is to be used with a

cold-water source only!

• Turn on the pressure washer, once all the air

has been expelled and water has reached the

end of the lance.

Electrical Cables

• Ensure that all cables are damage free before

connecting to the power supply.

Plug in the pressure washer and turn the unit

on with the main switch (2).

4. USE

CAUTION! The cleaner must only be

used with clean water; use of unfiltered

water or corrosive chemicals will damage

the cleaner.

• Turn the motor switch to the “0” position.

• Check that the electrical supply voltage and

frequency (Volts/Hz) correspond to those

specified on the cleaner data plate.

• If the power supply is correct, you may now

plug in the cleaner.

• The electric supply connection shall be made

by a qualified electrician. It is recommended

that the electric supply to this appliance

should include either a residual current device

that will interrupt the supply if the leakage

current to earth exceeds 30 mA for 30 ms or a

device which will prove the earth circuit.

CAUTION! The machine may cause

electrical disturbances when starting.

• If the motor stops and fails to restart, wait 2-3

minutes before restarting. THERMAL CUTOUT

TRIPPED

Adjusting the nozzle

Fig. 2

• Water may be sprayed out of the nozzle either

linearly or in a fan shape. Turn on the pressure

first, and then adjust the nozzle.

Adjusting pressure

Fig. 3

Using High Pressure:

• Please make sure the trigger released and

there is not any water spraying. then turn the

rear part of spray nozzle counterclockwise.

Squeeze the trigger, the gun will spray water

with high pressure.

Using Low Pressure:

• Please make sure the trigger released and

there is not any water spraying. then turn the

rear part of spray nozzle clockwise. Squeeze

the trigger, the gun will spray water with low

pressure.

CAUTION: Selection of high or low

pressure by turning action. The selection

of the pressure must be carried out with

the gun in closed position.

Water inlet filter

Fig. 4

• The water inlet filter must be inspected regu-

larly, so as to avoid blockage and restriction of

the water supply to the pump. (fig 4)

Using the detergent bottle

Fig. 5

• Add detergent to the container.

• Set the Adjustable Spray Wand at low pressure

position.

• Trigger gun to spray detergent.

The use of detergents can dramatically reduce

cleaning time and assist in the removal of difficult

stains. Some detergents have been customized

for pressure washer use on specific cleaning

tasks. These detergents are approximately as

thick as water. The use of thicker detergents,

such as dish soap, will clog the chemical

injection system and prevent the application of

the detergent. The cleaning power of detergents

comes from applying them to a surface and

giving the chemicals time to break down the dirt

and grime. Detergents work best when applied

at low pressure. The combination of chemical

action and high pressure rinsing is very effective.

On vertical surfaces, apply the detergent starting

at the bottom and work your way upward. This

will prevent the detergent from sliding down and

causing streaks. High pressure rinsing should also

progress from the bottom to top. On particularly

tough stains, it may be necessary to use a brush

in combination with detergents and high pressure

rinsing.

CAUTION! Never disconnect the high-

pressure hose from the machine while

the system is still pressurized.

Follow the correct procedure:

1. Turn off the pressure washer by using the

switch on the machine.

2. Unplug the unit from the power source.

3. Turn off the water supply at the tap.

4. Press the trigger of the gun to depressurize the

system.

5. Disconnect the supply hose to the machine

6. Wipe all surfaces of the unit with a damp clean

cloth.

7. Engage the safety lock.

5. SERVICE & MAINTENANCE

Warning! Unplug the electric cable

(power source) prior to any maintenance

or preparatory storage operations.

• Make sure that the machine is not live when

carrying out maintenance work on the motor.

• To ensure good performance, check and clean

the suction and detergent filters after every 50

hours of operation.

Malfunction

Should the machine fail to function correctly, a

number of possible causes and the appropriate

solutions are given below:

1. When switched on, the machine will not

start working.

• Plug is not well connected or electric socket is

faulty.

• Check plug, socket and fuse.

• The mains voltage is lower than the minimum

requirement for start up.

• Check that the mains voltage is adequate.

• The pump is stuck.

• Refer to after storage instructions. Switch

off the unit and let the motor cool.

• Thermal safety has tripped.

• Leave the lance open with water coming

through.

2. Fluctuating pressure

• Pump sucking air

• Check that hoses and connections are

airtight

• Valves dirty, worn out or stuck. Pump seals

worn.

• Clean and replace or refer to dealer.

3. Water leaking from the pump

• Seals worn out

• Check and replace, or refer to dealer

4. The motor stops suddenly

• Thermal safety switch has tripped due to

overheating.

• Check that the mains voltage corresponds

to specifications. An extension cable,

which is too thin, and tool long can cause

a voltage drop and cause the motor to

overheat. Leave to cool down. Use heavy

duty extension cables.

5. The pump does not reach the necessary

pressure.

• Water inlet, filter is clogged

• Clean the water inlet filter

• Pump sucking air from connections or hoses

• Check that all supply connections are tight

• Suction/ delivery valves are clogged or worn

out.

• Check that the water feeding hose is not

leaking.

• Unloader valve is stuck

• Clear or respire valves

• Lance nozzle incorrect or worn out

• Loosen and re-tighten regulation screw

Check and/ or replace.

Repairs and servicing should only be

carried out by a qualified technician or

service firm.

Cleaning

Keep the ventilation slots of the machine clean to

prevent overheating of the engine.

Clean the housing regularly with a soft cloth,

preferably every time it is used.

Keep the air vents free f dust and dirt. Remove

stubborn dirt with a soft rag moistened in soapy

water. Do not use any solvents such as petrol,

alcohol, ammonia, etc. as such substances can

damage the plastic parts.

Lubrication

The appliance does not need any extra

lubrication.

Storage and transportation

Keep the high pressure washer in well-ventilated

dry premises with temperature not going below

+5ºC. Operate the cleaner with non-corrosive/

non-toxic antifreeze before storing for the winter.

Faults

If a fault arises through wear in an element,

please contact the service address shown on the

warranty card. A drawing of the spare parts that

may be obtained is included at the end of these

operating instructions.

ENVIRONMENT

To prevent damage during transport, the

appliance is delivered in a solid packaging which

consists largely of reusable material. Therefore

please make use of options for recycling the

packaging.

Damaged and/or disposed of electrical or

electronic devices must be dropped off

at recycling stations intended for that

purpose.

WARRANTY

Read the terms of warranty on the separate

warranty card which is enclosed.

123

2 3 4 5 6 7 24 25 26

1314151617181920

Exploded view A

Spare parts list

GRM1015

No. Description Position

501094 Filtre B 23

502196 valve set B 36- 42

501199 microswitch B 31

501238 water hose A 20

502095 wheel B 13 -16

503111 detergent spray attachment B 3-4

521223 lance extension A 22

521224 lance adjustable nozzle A 21

502099 trigger A 23

46 45

42 41

39 38

6162

Exploded view B

EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3,

EN 60745-1, EN 60745-2-3

2006/42/EC, 2006/95/EC, 2004/108/EC, 2011/65/EU, 2011/19/EU

Zwolle, 01-05-2015 H.G.F Rosberg

CEO FERM B.V.

FERM B.V. - Lingenstraat 6 - 8028 PM - Zwolle - The Netherlands

(EN) We declare under our sole responsibility that this product is in conformity with

directive 2011/65/EU of the European parliament and of the council of 9 June on the

restriction of the use of certain hazardous substances in electrical and electronic

equipment is in conformity and accordance with the following standards and

regulations:

(DE) Der Hersteller erklärt eigenverantwortlich, dass dieses Produkt der Direktive

2011/65/EU des Europäischen Parlaments und des Rats vom 8. Juni 2011 über die

Einschränkung der Anwendung von bestimmten gefährlichen Stoffen in elektrischen

und elektronischen Geräten entspricht. den folgenden Standards und Vorschriften

entspricht:

(NL) Wij verklaren onder onze volledige verantwoordelijk heid dat dit product voldoet aan

de conform Richtlijn 2011/65/EU van het Europees Parlement en de Raad van 8 juni

2011 betreffende beperking van het gebruik van bepaalde gevaarlijke stoffen in

elektrische en elektronische apparatuur en in overeenstem ming is met de volgende

standaarden en reguleringen:

(FR) Nous déclarons sous notre seule responsabilité que ce produit est conforme aux

standards et directives suivants: est conforme à la Directive 2011/65/EU du

Parlement Européen et du Conseil du 8 juin 2011 concernant la limitation d’usage de

certaines substances dangereuses dans l’équipement électrique et électronique.

(ES) Declaramos bajo nuestra exclusiva responsabilidad que este producto cumple con

las siguientes normas y estándares de funcionamiento: se encuentra conforme con

la Directiva 2011/65/UE del Parlamento Europeo y del Consejo de 8 de junio de 2011

sobre la restricción del uso de determinadas sustancias peligrosas en los equipos

eléctricos y electrónicos.

(PT) Declaramos por nossa total responsabilida-de que este produto está em

conformidade e cumpre as normas e regulamentações que se seguem: está em

conformidade com a Directiva 2011/65/EU do Parlamento Europeu e com o

Conselho de 8 de Junho de 2011 no que respeita à restrição de utilização de

determinadas substâncias perigosas existentes em equipamento eléctrico e

electrónico.

(IT) Dichiariamo, sotto la nostra responsabilità, che questo prodotto è conforme alle

normative e ai regolamenti seguenti: è conforme alla Direttiva 2011/65/UE del

Parlamento Europeo e del Consiglio dell’8 giugno 2011 sulla limitazione dell’uso di

determinate sostanze pericolose nelle apparecchiature elettriche ed elettroniche.

(SV) Vi garanterar på eget ansvar att denna produkt upp fyller och följer följande

standarder och bestämmelser: uppfyller direktiv 2011/65/EU från Europeiska

parlamentet och EG-rådet från den 8 juni 2011 om begränsningen av användning av

farliga substanser i elektrisk och elektronisk utrustning.

(FI) Vakuutamme yksinomaan omalla vastuullamme, että tämä tuote täyttää seuraavat

standardit ja säädökset: täyttää Euroopan parlamentin ja neuvoston 8. kesäkuuta

2011 päivätyn direktiivin 2011/65/EU vaatimukset koskien vaarallisten aineiden

käytön rajoitusta sähkö- ja elektronisissa laitteissa.

(NO) Vi erklærer under vårt eget ansvar at dette produktet er i samsvar med følgende

standarder og regler: er i samsvar med EU-direktivet 2011/65/EU fra Europa-

parlamentet og Europa-rådet, pr. 8 juni 2011, om begrensning i bruken av visse

farlige stoffer i elektrisk og elektronisk utstyr.

(DA) Vi erklærer under eget ansvar, at dette produkt er i overensstemmelse med følgende

standarder og bestemmelser: er i overensstemmelse med direktiv 2011/65/EU fra

Europa-Parlamentet og Rådet af 8. juni 2011 om begrænsning af anvendelsen af

visse farlige stoffer i elektrisk og elektronisk udstyr.

(HU) Felelősségünk teljes tudatában kijelentjük, hogy ez a termék teljes mértékben

megfelel az alábbi szabványoknak és előírásoknak: je v souladu se směrnicí

2011/65/EU Evropského parlamentu a Rady EU ze dne 8. června 2011, která se týká

omezení použití určitých nebezpečných látek v elektrických a elektronických

zařízeních.

(CS) Na naši vlastní zodpovědnost prohlašujeme, že je tento výrobek v souladu s

následujícími standardy a normami: Je v súlade s normou 2011/65/EÚ Európskeho

parlamentu a Rady z 8. júna 2011 týkajúcej sa obmedzenia používania určitých

nebezpečných látok v elektrickom a elektronickom vybavení.

(SK) Vyhlasujeme na našu výhradnú zodpovednosť, že tento výrobok je v zhode a súlade

s nasledujúcimi normami a predpismi: Je v súlade s normou 2011/65/EÚ Európske

ho parlamentu a Rady z 8. júna 2011 týkajúcej sa obmedzenia používania určitých

nebezpečných látok v elektrickom a elektronickom vybavení.

(SL) S polno odgovornostjo izjavljamo, da je ta izdelek v skladu in da odgovarja nasledn

jim standardom terpredpisom: je v skladu z direktivo 2011/65/EU Evropskega parla-

menta in Sveta z dne 8. junij 2011 o omejevanju uporabe določenih nevarnih snovi v

električni in elektronski opremi.

(PL) Deklarujemy na własną odpowiedzialność, że ten produkt spełnia wymogi zawarte w

następujących normach i przepisach: jest zgodny z Dyrektywą 2001/65/UE Parla

mentu Europejskiego i Rady z dnia 8 czerwca 2011 r. w sprawie ograniczenia stoso-

wania niektórych niebezpiecznych substancji w sprzęcie elektrycznym i elektronic-

znym.

(LT) Prisiimdami visą atsakomybę deklaruojame, kad šis gaminys atitinka žemiau

paminėtus standartus arba nuostatus: atitinka 2011 m. birželio 8 d. Europos

Parlamento ir Tarybos direktyvą 2011/65/EB dėl tam tikrų pavojingų medžiagų

naudojimo elektros ir elektroninėje įrangoje apribojimo.

(LV) Ir atbilstoša Eiropas Parlamenta un Padomes 2011. gada 8. jūnija Direktīvai

2011/65/ES par dažu bīstamu vielu izmantošanas ierobežošanu elektriskās un

elektroniskās iekārtās.

(ET) Apgalvojam ar visu atbildību, ka šis produkts ir saskaņā un atbilst sekojošiem stand

artiem un nolikumiem: ir atbilstoša Eiropas Parlamenta un Padomes 2011. gada 8.

jūnija Direktīvai 2011/65/ES par dažu bīstamu vielu izmantošanas ierobežošanu

elektriskās un elektroniskās iekārtās.

(RO) Declarăm prin aceasta cu răspunderea deplină că produsul acesta este în

conformitate cu următoarele standarde sau directive: este în conformitate cu

Directiva 2011/65/UE a Parlamentului European şi a Consiliului din 8 iunie 2011 cu

privire la interzicerea utilizării anumitor substanţe periculoase la echipamentele

electrice şi electronice.

(HR) Izjavljujemo pod vlastitom odgovornoĻśu da je strojem ukladan sa slijedeśim

standardima ili standardiziranim dokumentima i u skladu sa odredbama: usklađeno s

Direktivom 2011/65/EU europskog parlamenta i vijeća izdanom 8. lipnja 2011. o

ograničenju korištenja određenih opasnih tvari u električnoj i elektroničkoj opremi.

(SRL) Pod punom odgovornošću izjavljujemo da je usaglašen sa sledećim standardima ili

normama: usaglašen sa direktivom 2011/65/EU Evropskog parlamenta i Saveta od

8.juna.2011. godine za restrikciju upotrebe određenih opasnih materija u električnoj i

elektronskoj opremi.

(RU) Под свою ответственность заявляем, что данное изделие соответствует

следующим стандартам и нормам: соответствует требованиям Директивы

2011/65/EU Европейского парламента и совета от 8 июня 2011 г. по

ограничению использования определенных опасных веществ в электрическом

и электронном оборудовании

(UK) На свою власну відповідальність заявляємо, що дане обладнання відповідає

наступним стандартам і нормативам: задовольняє вимоги Директиви 2011/65/

ЄС Європейського Парламенту та Ради від 8 червня 2011 року на обмеження

використання деяких небезпечних речовин в електричному та електронному

обладнанні.

(EL) Δηλώνουμε υπεύθυνα ότι το προϊόν αυτό συμφωνεί και τηρεί τους παρακάτω

κανονισμούς και πρότυπα: συμμορφώνεται με την Οδηγία 2011/65/ΕΕ του Ευρωπαϊκού

Κοινοβουλίου και του Συμβουλίου της 8ης Ιουνίου 2011 για τον περιορισμό της χρήσης

ορισμένων επικίνδυνων ουσιών σε ηλεκτρικό και ηλεκτρονικό εξοπλισμό.

(AR) نعلن على مسئوليتنا وحدنا أن هذا المنتج يتوافق مع المعايير والتوجيهات التالية:

(TR) Tek sorumlusu biz olarak bu ürünün aşağıdaki standart ve yönergelere uygun olduğunu

beyan ederiz.

DECLARATION OF CONFORMITY

GRM1015 - HIGH PRESSURE CLEANER

1504-29

Ferm GRM1015 Manual de utilizare

Marca: Ferm

Model: GRM1015

Categorie: Curatatoare de inalta presiune

Tip: Manual de utilizare

Descărcați PDF

raport

în alte limbi

English: Ferm GRM1015 User manual

Lucrări conexe

Ferm GRM1012 Manualul proprietarului

Ferm GRM1015 Manual de utilizare

Ferm GRM1015 Manual de utilizare

în alte limbi

Lucrări conexe

Alte documente