Sames FPro S Manual de utilizare

Marca: Sames

Model: FPro S

Categorie: Pulverizator de vopsea

Tip: Manual de utilizare

DOCUMENTATION

AIRSPRAY GUN

FPro S

Manual : 582.126.110-UK - 1912

Date: 20/12/19

Supersede : 31/10/19

Modif.: Update

TRANSLATION FROM THE ORIGINAL MANUAL

IMPORTANT : Before assembly and start-up, please read and clearly understand all the documents relating to

this equipment (professional use only).

THE PICTURES AND DRAWINGS ARE NON CONTRACTUAL. WE RESERVE THE RIGHT TO MAKE CHANGES WITHOUT PRIOR NOTICE..

SAMES KREMLIN SAS

13, chemin de Malacher

38 240 - MEYLAN - France



: 33 (0)4 76 41 60 60

www.sames-kremlin.com

SAMES KREMLIN N° : 578.147.130-1909

578.147.130 1909

SAMES KREMLIN SAS

13, chemin de Malacher

38 240 - MEYLAN - France



: 33 (0)4 76 41 60 60

www.sames-kremlin.com

FR UK DE

Pour une utilisation sure, Il est de votre

responsabilité de :

 Lire attentivement tous les documents contenus

dans le CD joint avant la mise en service de

l’équipement,

 D’installer, d’utiliser, d’entretenir et de réparer

l’équipement conformément aux préconisations de

SAMES KREMLIN ainsi qu’aux réglementations

nationales et/ou locales,

 Vous assurez que les utilisateurs de cet

équipement ont été formés, ont parfaitement compris

les règles de sécurité et qu’ils les appliquent.

To ensure safe use of the machinery, it is your

responsibility to:

 Carefully read all documents contained on the

enclosed CD before putting the machinery into service,

 Install, use, maintain and repair the machinery in

accordance with SAMES KREMLIN's

recommendations and national and/or local

regulations,

 Make sure that the users of the machinery have

received proper training and that they have perfectly

understood the safety rules and apply them.

Eine sichere Nutzung setzt voraus, dass Sie: :

 alle in der CD enthaltenen Dokumente vor der

Inbetriebnahme der Anlage aufmerksam lesen,

 die Anlage im Einklang mit den Empfehlungen von

SAMES KREMLIN sowie mit den nationalen und/oder

lokalen Bestimmungen installieren, verwenden,

warten und reparieren,

 sich vergewissern, dass die Nutzer dieser Anlage

angemessen geschult wurden, die

Sicherheitsbestimmungen verstanden haben und sie

anwenden.

ES IT PT

Para una utilización segura, será de su

responsabilidad:

 leer atentamente todos los documentos que se

incluyen en el CD adjunto antes de la puesta en

servicio del equipo,

 instalar, utilizar, efectuar el mantenimiento y

reparar el equipo con arreglo a las recomendaciones

de SAMES KREMLIN y a la normativa nacional y/o

local,

 cerciorarse de que los usuarios de este equipo han

recibido la formación necesaria, han entendido

perfectamente las normas de seguridad y las aplican.

Per un uso sicuro, vi invitiamo a:

 leggere attentamente tutta la documentazione

contenuta nel CD allegato prima della messa in

funzione dell'apparecchio,

 installare, utilizzare, mantenere e riparare

l'apparecchio rispettando le raccomandazioni di

SAMES KREMLIN, nonché le normative nazionali e/o

locali,

 accertarvi che gli utilizzatori dell'apparecchio

abbiano ricevuto adeguata formazione, abbiano

perfettamente compreso le regole di sicurezza e le

applichino.

Para uma utilização segura, é da sua

responsabilidade:

 Ler atentamente todos os documentos incluídos

no CD em anexo antes de pör o equipamento em

funcionamento,

 Proceder à instalação, utilização, manutenção e

reparação do equipamento de acordo com as

preconizações de SAMES KREMLIN, bem como com

outros regulamentos nacionais e/ou locais aplicáveis,

 Assegurar-se que os utilizadores do equipamento

foram devidamente capacitados, compreenderam

perfeitamente e aplicam as devidas regras de

segurança.

NL SE FI

Voor een veilig gebruik dient u:

 alle document op de bijgevoegde cd aandachtig te

lezen alvorens het apparaat in werking te stellen,

 het apparaat te installeren, gebruiken,

onderhouden en repareren volgens de door SAMES

KREMLIN gegeven aanbevelingen en overeenkomstig

de nationale en/of plaatselijke reglementeringen,

 zeker te stellen dat de gebruikers van dit apparaat

zijn opgeleid, de veiligheidsregels perfect hebben

begrepen en dat zij die ook toepassen.

För en säker användning av utrustningen ansvarar ni

för följande:

 Läs noga samtliga dokument som finns på den

medföljande cd-skivan innan utrustningen tas i drift.

 Installera, använd, underhåll och reparera

utrustningen enligt anvisningarna från SAMES

KREMLIN och enligt nationella och/eller lokala

bestämmelser.

 Försäkra er om att användare av denna utrustning

erhållit utbildning, till fullo förstått

säkerhetsföreskrifterna och tillämpar dem.

Käytön turvallisuuden varmistamiseksi

velvollisuutesi on:

 Lukea huolella kaikki CD:llä olevat asiakirjat ennen

laitteiston käyttöönottoa,

 Noudattaa laitteiston asennuksessa, käytössä,

kunnossapidossa ja huollossa SAMES KREMLIN in

suosituksia sekä kansallisia ja/tai paikallisia

määräyksiä,

 Varmistaa, että laitteiston käyttäjät ovat

koulutettuja ja ymmärtävät täysin

turvallisuusmääräykset ja miten niitä sovelletaan.

PL CS SL

Dla zapewnienia bezpiecznego użytkowania na

użytkowniku spoczywa obowiązek:

 Uważnego zapoznania się ze wszystkimi

dokumentami znajdującymi się na załączonej płycie CD

przed pierwszym uruchomieniem urządzenia,

 Instalowania, użytkowania, konserwacji i naprawy

urządzenia zgodnie z zaleceniami firmy SAMES

KREMLIN oraz z przepisami miejscowymi,

 Upewnienia, że wszyscy przeszkoleni użytkownicy

urządzenia zrozumieli zasady bezpieczeństwa i stosują

się do nich.

Pro bezpečné používání jste povinni:

 Před uvedením zařízení do provozu si pozorně

přečíst veškeré dokumenty obsažené na přiloženém

CD,

 Nainstalovat, používat, udržovat a opravovat

zařízení v souladu s pokyny firmy SAMES KREMLIN

a s národními a/nebo místními legislativními předpisy,

 Ujistit se, že uživatelé tohoto zařízení byli

vyškoleni, že dokonale pochopili bezpečnostní pravidla

a že je dodržují.

Za varno uporabo ste dolžni:

 natančno prebrati vse dokumente na CD pred

zagonom stroja,

 inštalirati, uporabljati, vzdrževati in popravljati

opremo po določilih SAMES KREMLIN in v skladu z

veljavnimi nacionalnimi in/ali lokalnimi predpisi,

 poskrbeti, da so uporabniki te opreme ustrezno

usposobljeni, poznajo varnostne predpise in da jih

upoštevajo.

SK HU RO

V záujme bezpečného je vašou povinnosťou:

 pozorne si prečítať všetky dokumenty obsiahnuté

na priloženom CD predtým, ako zariadenie uvediete do

prevádzky,

 nainštalovať, používať, udržiavať a opravovať

zariadenie v súlade s odporúčaniami spoločnosti

SAMES KREMLIN a národnými a/alebo miestnymi

predpismi,

 uistiť sa, že používatelia tohto zariadenia boli

zaškolení, riadne porozumeli pravidlám bezpečnosti a

používajú ich.

A biztonságos használat érdekében az Ön

felelőssége, hogy:

 a berendezés üzembe helyezése előtt figyelmesen

elolvassa a mellékelt CD által tartalmazott összes

dokumentumot,

 a berendezést a SAMES KREMLIN ajánlasainak

valamint a nemzeti és/vagy helyi szabályozásoknak

megfelelően helyezze üzembe, használja, tartsa

karban és javítsa,

 megbizonyosodjon róla, hogy a berendezés

felhasználói képzettek, tökéletesen megértették és

alkalmazzák a biztonsági előírásokat.

Pentru o utilizare sigură, este responsabilitatea dvs.

să:

 Citiţi cu atenţie toate documentele de pe CD-ul

anexat, înainte de punerea în funcţiune a

echipamentului,

 Instalaţi, utilizaţi, întreţineţi şi reparaţi

echipamentul conform instrucţiunilor SAMES

KREMLIN precum şi reglementărilor naţionale şi/sau

locale,

 Vă asiguraţi că utilizatorii acestui echipament au

fost instruiţi, au înţeles perfect regulile de securitate şi

le aplică integral.

Déclaration(s) de conformité au verso de ce document / Declaration(s) of conformity at the back of this document / Konformitätserklärung(en) auf der Rückseite dieser Unterlage

/ Declaración (es) de conformidad en el reverso de este documento / Dichiarazione/i di conformità sul retro del presente documento

/ Declaração(ções) de conformidade no verso do documento / Conformiteitsverklaring(en) op de keerzijde van dit document / Försäkran om överensstämmelse på omstående

sida av detta dokument / Vaatimustenmukaisuusvakuutukset tämän asiakirjan kääntöpuolella / Deklaracja(e) zgodności na odwrocie dokumentu

/ Prohlášení o shodě se nachází/nacházejí na zadní straně tohoto dokumentu / Deklaracija(e) o skladnosti na hrbtni strani tega dokumenta / Vyhlásenie/-a o zhode sa nachádzajú

na zadnej strane dokumentu / A dokumentum hátlapján szereplő megfelelőségi nyilatkoz(ok) / Declaraţii de conformitate pe versoul acestui document

SAMES KREMLIN - 2 - N° : 578.147.130-1909

DECLARATION UE DE CONFORMITE

EU DECLARATION OF CONFORMITY

EU- KONFORMITÄTSERKLÄRUNG

DECLARACIÓN UE DE CONFORMIDAD

DICHIARAZIONE DI CONFORMITÀ UE

DECLARAÇÃO UE DE CONFORMIDADE

EU-CONFORMITEITSVERKLARING

EU-FÖRSÄKRAN OM ÖVERENSSTÄMMELSE

EU- VAATIMUKSENMUKAISUUSVAKUUTUS

DEKLARACJA ZGODNOŚCI UE

EU PROHLÁŠENÍ O SHODĚ

IZJAVA EU O SKLADNOSTI

VYHLÁSENIE O ZHODE

EU-MEGFELELŐSÉGI NYILATKOZAT

DECLARAŢIA DE CONFORMITATE UE

Le fabricant / The manufacturer / Der Hersteller

/ El fabricante / Il produttore / O fabricante

/ De fabrikant / Tillverkare / Valmistaja / Producent / Výrobce

/ Proizvajalec / Výrobca / Gyártó / Fabricantul:

SAMES KREMLIN SAS

13, chemin de Malacher

38 240 - MEYLAN - FRANCE

Tél. : 33 (0)4 76 41 60 60

Déclare que le matériel désigné ci-après / Herewith declares that the equipment / erklärt hiermit, dass die / Declara que el material designado a

continuación / Dichiara che il materiale sottoindicato / Declara que o material a seguir designado / verklaart dat de hieronder aangeduide apparatuur

/ Kungör att den utrustning som anges här nedan / ilmoittaa, että alla mainitut laitteistot / Oświadcza, że wymienione poniżej urządzenia / Prohlašuje,

že níže uvedené vybavení / Izjavlja, da je opisana oprema spodaj / Vyhlasuje, že zariadenie uvedené nižšie / Kijelenti, hogy a megjelölt anyag a

továbbiakban / Declară că echipamentul precizat mai jos:

PISTOLETS MANUELS DE PULVERISATION PNEUMATIQUES / AIRSPRAY MANUAL SPRAYING GUNS

/ LUFTZERSTÄUBENDE HAND-SPRITPISTOLEN / PISTOLAS MANUALES DE PULVERIZACIÓN AEROGRÁFICA

FPRO S CONV

Est conforme à la législation d’harmonisation de l’Union applicable suivante / Is in conformity with the relevant Union harmonisation legislation / Erfüllt

die einschlägigen Harmonisierungsrechtsvorschriften der Union / es conforme con la legislación de armonización pertinente de la Unión / è conforme

alla pertinente normativa di armonizzazione dell’Unione / in overeenstemming met de desbetteffende harmonisatiewetgeving van de Unie / med den

relevanta harmoniserade unionslagstiftningen / on asiaa koskevan unionin yhdenmukaistamislainsäädännön vaatimusten mukainen / jest zgodny z

odnośnymi wymaganiami unijnego prawodawstwa harmonizacyjnego / Shoduje se s následující příslušnou evropskou harmonizační legislativou

/ V skladu s harmonizirano zakonodajo Unije / Je v súlade s uplatniteľnými harmonizačnými právnymi predpismi EÚ / Megfelel a következő

alkalmazandó uniós harmonizációs szabályozásnak / Este conform cu legislaţia aplicabilă de armonizare de mai jos

Directive ATEX / ATEX Directive / ATEX Richtlinie / Directiva ATEX / Direttiva ATEX / Diretiva ATEX

/ ATEX-Richtijn / ATEX-direktivet / ATEX-direktivi / Dyrektywa ATEX / Směrnice ATEX / Direktiva ATEX / Smernica ATEX

/ ATEX-irányelv

2014/34/UE

II 2G Ex h IIB T6 X Gb

EN 1953

Procédure d’évaluation de la conformité : Module A Documentation technique (Annexe VIII) archivée par : / Conformity

assessment procedure: Module A Technical documentation (ANNEX VIII) recorded by: / Verfahren zur Konformitätsbewertung:

Modul A Technische Unterlagen (ANLAGE VIII) archiviert durch: / Procedimiento de evaluación de la conformidad: Módulo A

Documentación técnica (ANEXO VIII) archivada por: / Procedura di valutazione della conformità: Modulo A Documentazione

tecnica (ALLEGATO VIII) archiviata a cura di: / Procedimento de avaliação da conformidade: Módulo A Documentação técnica

(ANEXO VIII) arquivada por: / Conformiteitsbeoordelingsprocedure: Module A Technische documentatie (BIJLAGE VIII)

gearchiveerd door: / Förfarande för bedömning av överensstämmelse: Modul A Teknisk dokumentation (BILAGA VIII) arkiverad

av: / Vaatimustenmukaisuusarviointimenetelmä: moduuli A Tekninen dokumentaatio (LIITE VIII) arkistoitu:

/ Procedura oceny zgodności: Moduł A Dokumentacji technicznej (ZAŁĄCZNIK VIII) zarchiwizowane przez: / Postup

posuzování shody: Modul A Technická dokumentace (PŘÍLOHA VIII) archivována: / Postopek preverjanja skladnosti: Modul A

Tehnična dokumentacija (PRILOGA VIII), arhiviral: / Postup posudzovania zhody: Modul A

Technická dokumentácia (PRÍLOHA VIII) archivovaná prostredníctvom: / Megfelelőségértékelési eljárás: A. modul Műszaki

dokumentáció (VIII. MELLÉKLET) archiválta: / Procedura de evaluare a conformităţii: Modulul A

Documentaţia tehnică (ANEXA VIII) este arhivată de:

INERIS 0080 - 60550 Verneuil-en-Halatte - France

SAMES KREMLIN - 3 - N° : 578.147.130-1909

La présente déclaration de conformité est établie sous la seule responsabilité du fabricant / This declaration of conformity is issued under the sole

responsibility of the manufacturer / Die alleinige Verantwortung für die Ausstellung dieser Konformitätserklärung trägt der Hersteller / La presente

declaración de conformidad se expide bajo la exclusiva responsabilidad del fabricante / La presente dichiarazione di conformità è rilasciata sotto la

responsabilità esclusiva del fabbricante / A presente declaração de conformidade é emitida sob a exclusiva responsabilidade do fabricante / Deze

conformiteitsverklaring wordt verstrekt onder volledige verantwoordelijkheid van de fabrikant / Denna försäkran om överensstämmelse utfärdas på

tillverkarens eget ansvar / Tämä vaatimustenmukaisuusvakuutus on annettu valmistajan yksinomaisella vastuulla / Niniejsza deklaracja zgodności

wydana zostaje na wyłączną odpowiedzianość producenta / Toto prohláŝení o skodě se vydává na výhradní odpovědnost výrobce / Za izdajo te izjave

o skladnosti je odgovoren izključno proizvajalec / Toto vyhlásenie o zhode sa vydáva / na vlastnú zodpovednosť výrobcu / Ezt a megfelelőségi

nylatkozatot a gyártó kizárólagos felelőssége mellett adják ti / Prezenta declaraţie de conformitate este emisă pe răspunderea exclusivă a

producătorului.

Hervé WALTER

Directeur Innovation & Développement / Innovation & Development

Director / Direktor für Innovation & Entwicklung / Director de

Inovación y Desarrollo / Direttore Innovazione e sviluppo

/ Diretor de Inovação / Manager Innovatie en Ontwikkeling / Direktör

för Forskning och Utveckling / Innovaatio- ja kehitysjohtaja

/ Dyrektor ds. Innowacji I Rozwoju / Ředitel pro inovace a vývoj

/ Direktor za inovacije in razvoj / Riaditeľ pre inováciu a rozvoj

/ Innovációs és fejlesztési igazgató / Director Inovaţie şi Dezvoltare

Fait à Meylan, le / Established in Meylan, on / Geschehen zu Meylan, am / En Meylan, a / Redatto a Meylan, / Vastgesteld te Meylan, / Utformat i

Meylan, den / Meylan, Ranska, / Sporządzono w Meylan, dnia / Meylan, dnia / V Meylanu, / V Meylan dňa / Kelt Meylanban, / Întocmită la Meylan,

pe data de 06/09/2019 - 09/06/2019

SAMES KREMLIN N° : 578.001.130-UK-1804

INSTALLATION AND SAFETY

INSTRUCTIONS

TRANSLATION FROM THE ORIGINAL MANUAL

IMPORTANT :Before assembly and start-up, please read and clearly understand all the

documents relating to this equipment (professional use only).

THE PICTURES AND DRAWINGS ARE NON CONTRACTUAL. WE RESERVE THE RIGHT TO MAKE CHANGES WITHOUT

PRIOR NOTICE.

SAMES KREMLIN SAS

13, chemin de Malacher

38 240 - MEYLAN - France



: 33 (0)4 76 41 60 60

www.sames-kremlin.com

SAMES KREMLIN - 1 - N° : 578.001.130-UK-1804

1. SAFETY INSTRUCTIONS

GENERAL SAFETY INSTRUCTIONS

CAUTION : The equipment can be dangerous if you do not follow our

instructions concerning installation and servicing described in this manual

and in accordance with applicable European standards and local national safety

regulations.

Please carefully read all the instruction literature before operating your

equipment.

Only trained operators can use the equipment.

The foreman must ensure that the operator has understood the safety instructions for this equipment as

well as the instructions in the manuals for the different parts and accessories.

Read carefully all instruction manuals, label markings before operating the equipment.

Incorrect use may result in injury. This equipment is for professional use only. It must be used only for

what it has been designed for. Never modify the equipment. The parts and accessories supplied must be

regularly inspected. Defective or worn parts must be replaced.

Guards (motor cover, coupling shields, connectors,…) have been designed for a

safe use of the equipment.

The manufacturer will not be held responsible for bodily injury or failure and / or

property damage due to destruction, the overshadowing or the partial or total

removal of the guards.

Never exceed the equipment components' maximum working pressure.

Comply with regulations concerning safety, fire risks, electrical regulations in force in the country of final

destination of the material. Use only products or solvent compatible with the parts in contact with the

material (refer to data sheet of the material manufacturer).

PICTOGRAMS

ADFECG

NIP HAZARD WARNING

MOVING

ELEVATOR

WARNING

MOVING PARTS WARNING

MOVING SHOVEL DO NOT

EXCEED THIS

PRESSURE

HIGH

PRESSURE

HAZARD

HJLKMQ

RELIEF OR

DRAIN VALVE WARNING

HOSE UNDER

PRESSURE

WEAR GLASSES

OBLIGATORY WEAR OF

GLOVES IS

OBLIGATORY

PRODUCT

VAPOR

HAZARDS

WARNING

HOT PARTS OR

AREAS

NPR

ELECTRICAL

HAZARD WARNING

FIRE HAZARDS EXPLOSION

HAZARDS GROUNDING WARNING

(USER) WARNING

SERIOUS

INJURIES

SAMES KREMLIN - 2 - N° : 578.001.130-UK-1804

PRESSURE HAZARDS

Current legislation requires that an air relief valve be fitted in the air supply circuit to the air

motor to prevent over pressurisation. This safety feature,ensures that it is not possible to supply

the air motor with excessive air pressure that may cause injury.

Please ensure that a material drain valve is fitted in the fluid circuit to drain and depressurise the

circuit. Once depressurised and drained, work /servicing may then commence on the equipment

Please remember to close these valves when restarting the system.

HIGH PRESSURE INJECTION HAZARDS

When working with high pressure equipment, special care is required. Fluid leaks can occur.

There is a risk of material being injected to any exposed parts of body, this could cause severe

injury :

medical care must be sought immediately if paint is injected under the skin or in other

parts of the body (eyes, fingers).

never point the spray gun at any one. Never try to stop the spray with your hands or fingers

nor with rags or similars.

follow the shut down procedure and always depressurize air and fluid circuits before

carrying out any servicing on the gun (cleaning, checking, maintenance of the material or

cleaning of the gun nozzles).

for the guns equipped with a safety device, always lock the trigger when not in use.

FIRE - EXPLOSION - SPARKS - STATIC ELECTRICITY HAZARDS

A poor earth connection, inadequate ventilation, sparks or static electricity can cause an

explosion or fire. to avoid these risks when using or servicing SAMES KREMLIN equipment, the

following safety procedures must be followed :

ensure a good earth connection and ground the parts to be handled i.e. solvents, materials,

components and equipment,

ensure adequate ventilation,

keep working area clean and free from waste solvents, chemicals, or solid waste i.e. rags,

paper and empty chemicals drums,

never use electrical switches / power if in an atmosphere of volatile solvent vapour,

stop working immediately in case of electrical arcs,

never store chemicals and solvents in the working area.

use paint whose flash point is the highest possible to prevent from any formation of gas

and inflammable vapours (refer to materials' safety instructions),

install a cover on the drums to reduce the diffusion of gas and vapours in the spraybooth.

TOXIC PRODUCT HAZARDS

Toxic products or vapours can cause severe injury not only though contact with the body, but also

if the products are ingested or inhaled. It is imperative :

to know the material products and their risks,

notified or hazardous materials must be stored in accordance with the regulations,

the material must be stored in an appropriate container, never place materials in a

container where there is a risk of spillage or leakage,

a procedure must be applied for the safe disposal of waste material. It must comply with all

prevailing regulations and legislations of the country where the equipment is to be used,

protective clothing should always be worn in compliance with the material manufacturers'

recommendations,

depending on the application and chemical safety instructions, safety glasses, hearing

protective earplug, gloves, foot wear, protective masks and possible breathing equipment

should be worn to comply with the regulations (Refer to chapter "Safety equipment of

SAMES KREMLIN selection guide).

SAMES KREMLIN - 3 - N° : 578.001.130-UK-1804

CAUTION!

It is forbidden to use material containing high concentrations of halogenated hydrocarbon

solvents with aluminium or zinc fillers .Non-compliance with the instructions may cause

explosion risk causing serious or fatal injury.

EQUIPMENT REQUIREMENTS

Guards (motor cover, coupling shields, connectors,…) have been designed for

a safe use of the equipment.

The manufacturer will not be held responsible for bodily injury or failure

and / or property damage due to destruction, the overshadowing or the

partial or total removal of the guards.

PUMP

Before carrying out any work, it is imperative to read and clearly understand the disassembly and

reassembly instructions before servicing. The operator must understand the equipment and the

safety instructions. These instructions are available in the equipment manuals.

The air motor is designed to be mounted with a pump. Never modify any components or

couplings. When operating, please keep hands away from moving parts. Before starting up the

equipment, please read the PRESSURE RELIEF instructions. Please ensure that any relief or

drain valves fitted are in good working order.

HOSES

Keep hoses out of circulation areas, moving parts or hot surfaces,

Never expose product hoses to temperature higher than + 60°C / 140° F or lower than 0°C

/ 32° F,

Never pull or use the hoses to move the equipment,

Tighten all fittings as well as the hoses before operating the equipment,

Check the hoses regularly; change them if they are damaged,

Never exceed the maximum working pressure (MWP) indicated on the hose.

USED PRODUCTS

Considering the wide variety of products that are available and can be used in our equipment it is

impossible to check and make recommendations for all chemical data,regarding the risks of

possible chemical attack and their long term chemical reaction

SAMES KREMLIN can not be held liable for :

compatibility of wetted parts,

risks to staff and the surroundings,

for worn or defective parts, for faulty equipment or units, or the qualitiy of final product.

It is the responsibility of the user to know and prevent any possible risks such as toxic vapours,

fires or explosions. He shall determine the risks of immediate reactions or pursuant to repeated

exposures of the staff,

SAMES KREMLIN shall not be liable for physical injuries, direct or indirect material damages

caused by the use of chemicals.

SAMES KREMLIN - 4 - N° : 578.001.130-UK-1804

2. HANDLING

Check the weight and the dimensions of the equipment

(



refer to 'Technical features' section of the instruction manual

If weight and dimensions are too important, the unloading must be carried out by means of a forklift or

any other appropriate means with a qualified personnal and in a clear horizontal area to prevent from

risks of damage injury or an accident.

The centre of gravity is not in the centre of the machine : carry out by hand a stability-test after having

lifted the whole at 10 cm / 3.937" maximum.

After the unloading, the handling of the whole (eg: elevator pump) is carried out by means of a pallet

truck taking the bottom part of the frame.

Remark : Each pump motor is fitted with a ring. The ring is designed for the hoisting of one

pump and can not be used for the handling of the complete assembly.

3. STORING

Storing before installation :

- Storing ambient temperature : 0 / +50 °C / 0 / +122°F

- Protect the whole against dust, water trickling, dampness and shocks.

Storing after installation :

- Operating temperature : +15 / +35 °C / +59 / +138.2° F

- Protect the whole against dust, water tricling, dampness and shocks.

4. INSTALLATION OF THE EQUIPMENT

The machine is installed on a stable horizontal floor (for eg a concrete flag).

The machine shall be made stable by the use of holding down bolts or by the use of other anchoring

methods, strong enough to prevent unintended bodily movement of the equipment.

To avoid risks caused by static electricity, the equipment as well as its components must

be grounded.

For the pumping equipments (pumps, pneumatic rams, frame…), a section wire of 2.5

mm² is fixed on the material. Use this wire to connect the material to “the general ground”.

In case of severe environments (mechanical protection of the wire of earthing insufficient,

vibrations, mobile material…) where function damages at the ground are probable, the user

have to replace the provided wire of 2.5 mm² by a device more adapted to its environment

(wire with a more important section, bonding strip, fixing by thimble with eyelet…).

The continuity of the ground must be controlled by a qualified electrician. If the continuity of

the ground is not ensured, check the terminal, the wire and the earthing point. Never use the

material without have solved this problem.

In the severe cases of environments (mechanical protection of the wire of earthing

insufficient, vibrations, mobile material…) where damages of the function put at the ground

are probable, the user will have to replace the wire of 2.5 mm² provided, by a device more

adapted to its environment (wire of more important section, bonding strip, fixing by thimble

with eyelet…),

The gun must be 'grounded' via a material hose or an air hose. In case of spraying by

means of a gun with cup, the air hose must be conductive,

The materials to be painted must also be grounded.

All the materials situated in the working area shall be grounded.

SAMES KREMLIN - 5 - N° : 578.001.130-UK-1804

Never store more than necessary inflammable materials inside the working area,

The materials must be stored into approved drums and grounded,

Use only grounded metals containers for the use of cleaning solvents,

Cardboard and paper are prohibited.

5. MARKING OF THE EQUIPMENT

Each equipment has a label plate with the name of the manufacturer, the equipment part number,

the interesting informations to use correctly the equipment (pressure, voltage,…) and sometimes

the above pictogram.

The equipment is designed with and consists of high quality materials and components which can

be re-used.

The 2012/19/UE European Directive covers all equipments with a crossed-out bin pictogram.

Please inform yourself about the collection systems for electric and electronic equipments.

Please act in accordance with local rules and do not dispose of old equipment with household

wastes. A correct disposal of old equipment will help prevent negative consequences for the

environment and health.

SAMES KREMLIN N° : 578.229.110-UK-1912

AIRSPRAY GUN

FPro S

Disassembly / Reassembly

TRANSLATION FROM THE ORIGINAL MANUAL

IMPORTANT : Before assembly and start-up, please read and clearly understand all the

documents relating to the equipment (professional use only).

THE PICTURES AND DRAWINGS ARE NOT CONTRACTUAL. WE RESERVE THE RIGHT TO MAKE CHANGES WITHOUT PRIOR

NOTICE.

SAMES KREMLIN SAS

13, chemin de Malacher

38 240 - MEYLAN - France



: 33 (0)4 76 41 60 60

www.sames-kremlin.com

SAMES KREMLIN - 1 - N° : 578.229.110-UK-1912

CAUTION :

Before any intervention, shut off the compressed air supply and depressurize the

circuits by triggering the gun. controlling the opening of the gun.

The gun is manufactured under the ATEX agreement and can not be modified.

SAMES KREMLIN will not be held responsible for any failure to comply with that

instruction.

Before removing a component of the gun, some precautions have to be taken :

- Shut off the fluid pressure,

- Empty out the paint inside the cup or the receiver and clean it,

- Fill the cup or the receiver with cleaning solvent,

- Take off the gun spraying air cap,

- Shut off the gun supply air pressure,

- Adjust fluid pressure to 0.5 bar / 7.25 psi and let the solvent circulate,

- Shut off the fluid pressure,

- Remove the part to be cleaned or changed.

Before reassemblying the different components, some precautions must be taken :

- Clean all the parts with the appropriate cleaning solvent and a brush.

- Install new seals if it is necessary after having lubricated them with PTFE grease.

- Install new parts if it is necessary.

SAMES KREMLIN - 2 - N° : 578.229.110-UK-1912

FPRO S CONV

Index Instructions Description Part number

A 1 PTFE grease PTFE grease (10 ml / 0.0026 US gal) 560.440.101

C 2 Low strength

- Anaerobic Adhesive

Loctite 222 (50 ml / 0.013 US gal) 554.180.010

S 1 Torque screwing :

18 Nm / 13.276 Ft/Lbs

S 2 Torque screwing :

10 Nm / 7.376 Ft/Lbs

A 1

S 1

A 1

C 2

S 2

C 2

SAMES KREMLIN - 3 - N° : 578.229.110-UK-1912

 PROJECTOR (IND. 1 + 7 + 11) & VORTEX (IND. 18) REPLACEMENT

Unscrew the aircap assembly (1), then remove the aircap ring (2), the aircap only (4), the stop ring

(5) and the ring seal (6).

Trigger the gun (36) then unscrew the nozzle assembly (7) with the wrench provided with the gun.

Remove the distribution ring (8) and the nozzle seal (10).

Remove the vortex (18) and the distribution ring (19).

Unscrew the needle stop (22), then remove the needle spring (20) and the needle (11) by the rear

part of the gun.

Check parts’ conditions. Change them if necessary.

Lubricate the needle (11) and the needle spring (20) with grease.

Reinstall them as well as the needle stop (22).

Reinstall the distribution ring (19) and the vortex (18).

Reinstall the new nozzle assembly (7) - screwing torque : 18 Nm / 13.276 Ft/Lbs.

Reinstall the new aircap assembly (1).

NOTA : the gun can operate without vortex (18) if necessary.

SAMES KREMLIN - 4 - N° : 578.229.110-UK-1912

 NEEDLE PACKING (IND. 13) REPLACEMENT

Make sure there is no more paint inside the gun.

Unscrew the needle stop (22) and remove the needle spring (20).

Remove the needle (11) completely by the rear part of the gun.

Dismount the trigger (36) by removing the screw (39) and the trigger spindle (38) by means of two

wrenches n° 5.5.

Unscrew the packing holder (16) by means of the wrench supplied with the gun.

Take off the needle packing (13) that consists of a seat (14) and a bearing (15).

Insert the bearing (15) into the seat (14) and replace the whole in the gun.

Screw the packing holder (16) moderately.

Reinstall the needle (11).

Reinstall the lubricated needle spring (20) and the needle stop (22).

Tighten up the packing holder (16) by means of the wrench supplied with the gun and unscrew it by

a 1/4 turn.

Remount the trigger (36).

Feed paint

If there is a leak, screw slightly.

 AIR VALVE (IND. 23) REPLACEMENT

Unscrew the needle stop (22), then remove the needle spring (20) and the needle (11) by the rear

part of the gun.

Trigger the gun (36) then unscrew the needle stop sleeve (17) by means of the wrench supplied

with the gun.

Take off the valve spring (29) as well as the air valve body (24), the air valve stop (30) and the

carrier (28).

Reinstall the carrier (28) on the new air valve body (24).

Install that new assembly, the air valve stop (30), the lubricated valve spring (29) into the gun body.

Screw the needle stop sleeve (17).

Reinstall the needle (11), the lubricated needle spring (20) and the needle stop (22).

 AIR VALVE SEAL (IND. 26) REPLACEMENT

Take off the air valve (23) - refer to previous paragraph.

Remove the seal (26).

Lubricate the new seal (26) and place it in its housing.

 CAUTION : When reassembling, carefully insert the air valve (24) into the gun body

carrying out a rotary motion so as to preformate the valve seal (26).

SAMES KREMLIN - 5 - N° : 578.229.110-UK-1912

 TRIGGER (IND. 36) REPLACEMENT

Unscrew the needle stop (22) and take off the needle spring (20).

Remove the needle (11) completely by the rear part of the gun.

Dismount the trigger (36) by removing the screw (39) and the trigger spindle (38) by means of two

wrenches n° 5.5.

Reinstall the parts in the reverse order of the disassembly sequence. Apply previously low strength

- Anaerobic adhesive on the screw (39).

 AIR ADJUSTER ASSEMBLY (IND. 31 & IND. 40)

Unscrew the air adjuster (31and/or 40) by means of the wrench supplied with the gun.

Check the ring (32 and/or 41) condition and change it if necessary.

Reinstall the new air adjuster (31and/or 40) - screwing torque : 10 Nm / / 7.376 Ft/Lbs.

 AIR FITTING (IND. 35A/35B) REPLACEMENT

Unscrew the air fitting (35a/35b) from the gun (34) by means of the wrench supplied with the gun.

Install the new air fitting (35a/35b).

SAMES KREMLIN - 6 - N° : 578.229.110-UK-1912

 SUCTION CUP (IND. 50) REPLACEMENT

Unscrew the suction cup (50) on the fitting by means of the wrench supplied with the gun.

Unscrew the cup cover assembly and take off the cup seal, the filter (51a/51b) and the non-drop.

Reinstall the new non-drop, the new filter (51a/51b) and the new cup seal.

Screw the suction cup (50) on the fitting by means of the wrench supplied with the gun.

 VALVE DISPOSABLE CUP (IND . 55) REPLACEMENT

Unscrew the valve disposable cup (55) by means of the wrench supplied with the gun.

Unscrew the disposable cup on the fitting (the disposable cup is not for sale).

Reinstall the new disposable cup on the new valve (55).

Screw the valve disposable cup (55).

Doc. 573.521.050

Date/Datum/Fecha : 19/12/19

Annule/Cancels/

Ersetzt/Anula : 31/10/19

Modif. / Änderung : Ind. / Pos. 45 :

# 129 140 005  # 029 140 005

Pièces de rechange

Spare parts list

Ersatzteilliste

Piezas de repuesto

FPRO S CONV PISTOLET PNEUMATIQUE / AIRSPRAY GUN

PNEUMATISCHE PISTOLE / PISTOLA AEROGRÁFICA

F PRO S CONV

+ godet aluminium / aluminium cup

/ Aluminium Becher / bote de aluminio

(¤) #

135.780.000

+ CONV-12-Mvb 135.780.312

+ CONV-15-Mvb 135.780.315

+ CONV-18-Mvb 135.780.318

+ CONV-23-Lvb 135.780.423

+ CONV-27 Lvb 135.780.427

(¤) : pistolet sans projecteur / gun without projector / Pistole ohne Zerstäubereinheit / Pistola sin proyector

FPRO S CONV Standard / Estándar

Projecteur / Projector

/ Zerstäubereinheit

/ Proyector

Tête / Aircap

Luftkappe / Cabezal Buse / Nozzle

Düse / Boquilla Pointeau / Needle

Nadel / Aguja

Ind. 1+7+11 # Ind. 1 # Ind. 7 Ø (mm / ") # Ind. 11 #

CONV-12-Mvb 131 780 312

CONV

-07 22-Mvb 132 780 300

12 1,2 / 0.047 134 130 300 07 - 09

- 12 033 140 100

CONV-15-Mvb 131 780 315 15 1,5 / 0.059 134 130 600 15 - 18 033 140 200

CONV-18-Mvb 131 780 318 18 1,8 / 0.071 134 130 700

CONV-23-Lvb 131 780 423 CONV

-23 27-Lvb 132 780 400 23 2,3 / 0.09 134 131 100 23 - 27 033 140 300

CONV-27-Lvb 131 780 427 27 2,7 / 0.106 134 131 200

SAMES KREMLIN 2 Doc. / Dok. 573.521.050

Ind # Désignation Description Bezeichnung Denominación Qté

*1 - Tête complète

(voir tableau)

Aircap assembly

(refer to chart)

Zerstäuberkopf kpl.

(siehe Tabelle)

Cabezal completo

(consultar cuadro)

2 032 760 005  Bague de tête  Aircap ring  Haltering  Anillo del cabezal 1

3 129 080 007  Joint de tête (x 2)  Seal, aircap (x 2)  O-Ring (2 St.)  Junta de cabezal (x 2) 1

*4 NC / NS  Tête nue (voir tableau)  Aircap only (refer to

chart)

 Luftkappe (siehe

Tabelle)

 Cabezal solo (consultar

cuadro)

5 NC / NS  Anneau de retenue  Stop ring  Sicherungsring  Anillo de retención 1

6 150 040 309  Joint de bague (x 10)  Seal, ring (x 10)  O-Ring (10 St.)  Junta del anillo (x 10) 1

*7 - Buse équipée

(voir tableau)

Nozzle assembly

(refer to chart)

Düse kpl.

(siehe Tabelle)

Boquilla equipada

(consultar cuadro)

*8 129 130 004  Bague de répartition

(x 5)

 Distribution ring

(x 5)

 Luftverteilerring (5 St.)  Anillo de distribución

(x 5)

9 NC / NS  Buse  Nozzle  Düse  Boquilla 1

10 129 209 902  Joint de buse (x 5)  Seal, nozzle (x 5)  O-Ring, Düse (5 St.)  Junta de boquilla (x 5) 1

*11 - Pointeau (voir tableau) Needle (refer to chart) Farbnadel (siehe Tabelle) Aguja (consultar cuadro) 1

13 129 130 903 Garniture pointeau

(x 5)

Packing, needle

(x 5)

Nadelgarnitur

(5 St.)

Guarnicíón de aguja

(x 5)

14 NC / NS  Siège (x 5)  Seat (x 5)  Sitz (5 St.)  Asiento (x 5) 1

15 NC / NS  Palier (x 5)  Bearing (x 5)  Plastikeinsatz (5 St.)  Palier (x 5) 1

16 029 130 006  Presse-garniture (x 1)  Packing holder (x 1)  Packungsschraube

(1 St.)

 Prensa-guarnición (x 1) 1

SAMES KREMLIN 3 Doc. / Dok. 573.521.050

Ind # Désignation Description Bezeichnung Denominación Qté

17 029 030 003 Fourreau Sleeve, needle stop Nadelführung Manguito 1

18 129 140 031 Vortex (x 1) Vortex (x 1) Vortex (x 1) Vortex (x 1) 1

19 129 130 003 Bague de répartition

(x 5)

Distribution ring

(x 5)

Luftverteilerring (5 St.) Anillo de distribución

(x 5)

*20 050 311 248 Ressort de pointeau Spring, needle Farbnadelfeder Muelle de aguja 1

22 029 770 006 Butée de pointeau Needle stop Farbnadelanschlag Tope de aguja 1

*23 129 780 025 Soupape d'air complète Air valve assembly Luftventil kpl. Válvula de aire

completa

24 NC / NS  Corps de soupape  Body, valve  Luftventilkörper  Cuerpo de válvula 1

26 129 030 022  Joint de soupape (x 10)  Seal, valve (x 10)  Dichtung (10 St.)  Junta de válvula (x 10) 1

*28 129 030 026  Entraîneur (x 5)  Carrier (x 5)  Mitnehmer (5 St.)  Arrastre (x 5) 1

*29 050 311 321  Ressort de soupape  Spring, valve  Ventilfeder  Muelle de válvula 1

30 129 030 025  Joint de soupape (x 10)  Seal, valve (x 10)  Dichtung (10 St.)  Junta de válvula (x 10) 2

*31 129 130 020 Pointeau d’air (évents) Air adjuster assembly Druckluftregulier-

ventil

Aguja de aire (eventos) 1

32 NC / NS  Circlips Ø 6  Ring, model Ø 6  Sicherungsring Ø 6  Anillo truarc, tipo Ø 6 1

34 NC / NS Corps du pistolet Gun body Pistolenkörper Cuerpo de pistola 1

35a 050 102 624 Raccord d’air

M 1/4 G - M 1/4 NPS

Air fitting, model double

male 1/4 G - 1/4 NPS

Luftanschluss AG-AG

1/4NPS

Racor de aire,

tipo M 1/4 G - M 1/4 NPS

*36 129 780 906 Gâchette + axe de

gâchette + vis

Trigger + trigger spindle

+ screw

Abzugshebel + Achse

+ Schraube

Gatillo + eje de gatillo

+ tornillo

37 NC / NS  Gâchette  Trigger  Abzugshebel  Gatillo 1

*38

+39

129 140 904  Axe de gâchette (x 5)

+ vis (x 5)

 Trigger spindle (x 5)

+ screw (x 5)

 Abzugsachse (5 St.)

+ Schraube (5 St.)

 Eje de gatillo (x 5)

+ tornillo (x 5)

*40 129 130 030 Pointeau d’air (crosse) Air adjuster assembly Spritzstrahlregulier-

ventil

Aguja de aire

(empuñadura)

41 NC / NS  Circlips Ø 6  Ring, model Ø 6  Sicherungsring Ø 6  Anillo truarc, tipo Ø 6 1

45 029 140 005 Raccord produit Fluid fitting Materialanschluss Racor producto 1

50 138 400 000 Godet aspiration Suction cup Saugbecher Bote de aspiración 1

51a 138 310 300  Filtre 200µ (x 4)  Filter, 200µ (x 4)  Sieb 200µ (4 St.)  Filtro 200µ (x 4) 1

Pagina se încarcă ...

Sames FPro S Manual de utilizare

Marca: Sames

Model: FPro S

Categorie: Pulverizator de vopsea

Tip: Manual de utilizare

Descărcați PDF

raport

în alte limbi

English: Sames FPro S User manual

Sames FPro S Manual de utilizare

Sames FPro S Manual de utilizare

în alte limbi

Lucrări conexe