Whirlpool Climatiseur Mobile Monobloc 3500w 35m² - PAC W212 CO Manualul proprietarului

Instructions for use

Gebrauchsanweisung

Directives d’utilisation

Gebruiksaanwijzing

Libretto di istruzioni

Instrucciones de uso

Instruções de utilização

Инструкции за използване

Návod k obsluze

Brugsanvisninger

Käyttöohjeet

Οδηγίες χρήσης

Használati útmutató

Bruksanvisning

Instrukcja użytkownika

Návod na používanie

Instrucţiuni de utilizare

Инструкция по эксплуатации

Bruksanvisning

Інструкції з використання

-3-

PACW29COL

PACW29CO BK

PACW29HP

PACW29HP BK

PACW212CO

PACW212HP

PACB29CO

PACB29HP

PACB212HP

ENGLISH Instructions for use Page 4

DEUTSCH Bedienungsanleitung Seite 19

FRANÇAIS Consignes d’utilisation Page 34

NEDERLANDS Gebruiksaanwijzing Pagina 49

ITALIANO Istruzioni per l’uso Pagina 64

ESPAÑOL Instrucciones de uso Página 79

PORTUGUÊS Instruções de utilização Página 94

БЪЛГАРСКИ Инструкциизаизползване Страница109

ČESKY Návod k obsluze Strana 124

DANSK Brugsanvisninger Side 139

SUOMI Käyttöohje Sivu 154

ΕΛΛΗΝΙΚΑ Οδηγίεςχρήσης Σελίδα169

MAGYAR Használati útmutató 184. oldal

NORSK Brukerveiledning Side 199

POLSKI Instrukcjaużytkownika Strona214

SLOVENSKÝ Návodnapoužívanie Strana229

ROMÂNĂ Instrucţiunideutilizare Pagina244

РУССКИЙ Инструкцияпоэксплуатации Страница259

SVENSKA Bruksanvisning Sidan 274

УКРАЇНСЬКА Інструкціїзвикористання стор.289

-4-

SAFETY INSTRUCTIONS

IMPORTANT TO BE READ AND OBSERVED

• Download the complete instruction manual on docs.whirlpool.eu or call the phone

number shown on the warranty booklet.

• Before using the appliance, read these safety instructions. Keep them nearby for future

reference.

• These instructions and the appliance itself provide important safety warnings, to be

observed at all times. The manufacturer declines any liability for failure to observe

these safety instructions, for inappropriate use of the appliance or incorrect setting of

controls.

•

The appliance uses flammable refrigerant (R290),the maximum refrigerant charged

amount is 0.3kg.The appliance shall be installed,operated and stored in a room with a

floor area larger than 14.5m

2

. And the room should higher than 2.2 m.

The appliance was tested within 0.95 MPa - 1.05 MPa of external static pressures.

•

Very young children (0-3 years) should be kept away from the appliance. Young

children (3-8

years) should be kept away from the appliance unless continuously

supervised. Children from 8

years old and above and persons with reduced physical,

sensory or mental capabilities or lack of experience and knowledge can use this

appliance only if they are supervised or have been given instructions on safe use and

understand the hazards involved. Children must not play with the appliance. Cleaning

and user maintenance must not be carried out by children without supervision.

PERMITTED USE

•

CAUTION: the appliance is not intended to be operated by means of an external

switching device, such as a timer, or separate remote controlled system.

•

This appliance is intended to be used in household and similar applications such as:

hotels and working offices.

•

This appliance is not for professional use.

•

Always turn off the air conditioner by remote control or power button on product

panel first.

Do not use the power supply circuit breaker or pull off the plug to turn it off.

Disconnect the air conditioner from the power supply if it is to be left unused for a long

period of time or during a hunder/lightning storm.

-5-

SAFETY INSTRUCTIONS

Never insert obstacle in the air outlet-risk of injury. Keep ventilation openings clear

of any obstruction.

INSTALLATION

•

The appliance must be handled and installed by two or more persons - risk of injury.

Use protective gloves to unpack and install - risk of cuts.

•

Installation, including electrical connections, and repairs must be carried out by a

qualified technician according to national wiring rules.

Do not repair or replace any part of the appliance unless specifically stated in the user

manual.

Keep children away from the installation site. After unpacking the appliance, make sure

that it has not been damaged during transport.

In the event of problems, contact the dealer or your nearest After-sales Service.

Once installed, packaging waste (plastic, styrofoam parts etc.) must be stored out of

reach of children - risk of suffocation.

The appliance must be disconnected from all remote power supply before any

installation operation - risk of electric shock.

During installation, make sure the appliance does not damage the power cable - risk

of fire or electric shock. Only activate the appliance when the installation has been

completed.

The flexible exhaust hose allows placement of the air conditioner between 23” and

67” (60 cm and 170 cm) from window or door. The appliance with supplementary heater

needs to be kept a minimum distance of 100 cm from the combustible surface.

-6-

SAFETY INSTRUCTIONS

• Do not operate your air conditioner in a wet room such as a bathroom or laundry room.

•

Disconnect power cord before moving the appliance.

ELECTRICAL WARNINGS

•

The power supply must be of rated voltage with special circuitry for the appliance.

The diameter of the power cord must comply with requirements.

•

It must be possible to disconnect the appliance from the power supply by unplugging.

The appliance must be earthed in conformity with national electrical safety standards.

•

The use of a time-delay fuse or time-delay circuit breaker is recommended. All

wiring must comply with local and national electrical regulations and be installed by a

qualified electrician.

•

Do not use extension leads, multiple sockets or adapters. The electrical components

must not be accessible to the user after installation. Do not use the appliance when you

are wet or barefoot. Do not operate this appliance if it has a damaged power cable or

plug, if it is not working properly, or if it has been damaged or dropped.

•

If the supply cord is damaged, it must be replaced with an identical one by the

manufacturer, its service agent or similarly qualified persons in order to avoid a hazard-

risk of electrical shock.

•

Ensure safe grounding and a grounding wire connected with the special grounding

system of the building, installed by professionals. The appliance must be fitted with

electrical leakage protection switch and an auxiliary circuit breaker with sufficient

capacity. The circuit breaker must also have a magnetic and a thermal tripping function

to ensure protection in case of short-circuit and overload.

Model 9K & 12K

Required capacity of circuit breaker 16A (Fuse Type: 9k A+ HP,T3.15A/250VAC; Others,T5A/250VAC)

CLEANING AND MAINTENANCE

•

WARNING: Ensure that the appliance is switched off and disconnected from the

power supply before performing any maintenance operation; never use steam cleaning

equipment - risk of electric shock.

DISPOSAL OF PACKAGING MATERIALS

• The packaging material is 100% recyclable and is marked with the recycle symbol . The various parts of the packaging must

therefore be disposed of responsibly and in full compliance with local authority regulations governing waste disposal.

DISPOSAL OF HOUSEHOLD APPLIANCES

• This appliance is manufactured with recyclable or reusable materials. Dispose of it in accordance with local waste disposal

regulations. For further information on the treatment, recovery and recycling of household electrical appliances, contact your

local authority, the collection service for household waste or the store where you purchased the appliance. This appliance is

marked in compliance with European Directive 2012/19/EU, Waste Electrical and Electronic Equipment (WEEE). By ensuring this

product is disposed of correctly, you will help prevent negative consequences for the environment and human health.

The symbol

on the product or on the accompanying documentation indicates that it should not be treated as domestic

waste but must be taken to an appropriate collection center for the recycling of electrical and electronic equipment.

DECLARATION OF CONFORMITY

• The refrigerant gas being in a hermetically sealed system (R290, GWP 3 ).Please refer to the rating label for detailed information.

-7-

SAFETY INSTRUCTIONS

Explanation of symbols displayed unit.

WARNING

This symbol shows that this appliance uses a flammable

refrigerant.

If the refrigerant is leaked and exposed to an external ignition

source, there is a risk of fire

CAUTION

This symbol shows that the operation manual should be read

carefully

CAUTION

This symbol shows that a service personnel should be handling

this equipment with reference to the installation manual

CAUTION

This symbol shows that information is available such as the

operating manual or installation manual

SAFETY INSTRUCTIONS FOR SERVICING APPLIANCE WITH SPESIFIC REFRIGERANT

• Download the complete manual for detailed installation, servicing, maintenance and

reparing methods on docs.whirlpool.eu.

•

Do not use means to accelerate the defrosting process or to clean, other than those

recommended by the manufacturer.

•

The appliance shall be stored in a well-ventilated area where the room size

corresponds to the room area as specified for operation; without continuously

operating ignition sources (such as; open flames, an operating gas appliance or an

operating electric heater).

•

Do not pierce or burn. Be aware that the refrigerants may not contain an odor.

Any person who is involved with working on or breaking into a refrigerant circuit

should hold a current valid certificate from an industry-accredited assessment

authority, which authorizes their competence to handle refrigerants safely in

accordance with an industry recognized assessment specification. Servicing shall only

be performed as recommended by the equipment manufacturer. Maintenance and

repair requiring the assisstance of other skilled personnel shall be carried out under the

supervision of the person competent in the use of flammable refrigerants. Appliance

shall be installed, operated and stored in a room with a floor area larger than 14.5 m

2

. The

installation of pipe-work shall be kept to a room with a floor area larger than 14.5 m

2

. The

pipe-work shall be compliance with national gas regulations. The maximum refrigerant

charge amount is 0.3 kg.

When flared joints are reused , the flare part shall be re fabricated.

1. Transport of equipment containing flammable refrigerants shall be compliant with the

transport regulations.

2. Marking of equipment using signs shall be compliant with local regulations.

3. Disposal of equipment using flammable refrigerants shall be compliant with national

regulations.

Caution, risk of fire

C

-8-

SAFETY INSTRUCTIONS

4. The storage of equipment / appliances should be in accordance with the

manufacturer’s instructions.

5. Storage of packed (unsold) equipment Storage package protection should be

constructed such that mechanical damage to the equipment inside the package

will not cause a leak of the refrigerant charge. The maximum number of pieces of

equipment permitted to be stored together will be by local regulations.

6. Information on servicing.

6-1 Checks to the area

Prior to beginning work on system containing flammable refrigerants, safety checks are

necessary to ensure that the risk of ignition is minimized. For repair to the refrigerating

system the following precautions shall be complied with prior to conducting work on

the system.

6-2 Work procedure

Work shall be undertaken under a controlled procedure so as to minimize the risk of

flammable gas or vapour being present while the work is being performed.

6-3 General work area

All maintenance staff and others working in the local area shall be instructed on the

nature of work being carried out. Work in confied spaces shall be avoided.

6-4 Checking for presence of refrigerant

The area shall be checked with an appropriate refrigerant detector prior to and during

work, to ensure the technician is aware of prtentially flammable atmospheres. Ensure

that hte leak detection equipment being used is suitable for use with flammable

refrigerants, i.e. non-sparking adequately sealed or intrinsically safe.

6-5 Presence of fire extinguisher

If any hot work is to be conducted on the refrigerating equipment or any associated

partsappropriate fire extinguishing equipment shall be avalaible to hand. Have a dry

powder or CO2 fire extinguisher adjacent to the charging area.

6-6 No ignition sources

No person carrying out work in relation to a refrigerating system which involves exposing

any pipe work that contains or has contained flammable refrigerant shall use any

sources of ignition in such a manner that it may lead to the risk of fire or explosion.

All possible ignition sources, including cigarette smoking, should be kept sufficiently

far away from the site of installation, repairing, removing and disposal, during which

flammable refrigerant can possibly be released to the surrounding space. Prior to work

taking place, the area around the equipment is to be surveyed to make sure that there

are no flammable hazards or ignition risks. “No Smoking” signs shall be displayed.

6-7 Ventilated area

Ensure that the area is in the open or that it is adequately ventilated before breaking into

the system or conducting any hot work. A degree of ventilation shall continue during

the period that the work is carried out. The ventilation should safely disperse any

released refrigerant and preferably expel it externally into the atmosphere.

-9-

SAFETY INSTRUCTIONS

6-8 Checks to the refrigerating equipment

Where electrical components are being changed, they shall be fit for the purpose

and to the correct specification. At all times the manufacturer’s maintenance and

service guidelines shall be followed. If in doubt consult the manufacturer’s technical

department for assistance. The following checks shall be applied to installations using

flammable refrigerants:

- The actual refrigerant charge is in accordance with the room size within which the

refrigerant containing parts are installed;

- The ventilation machinery and outlets are operating adequately and are not obstructed;

- If an indirect refrigerating circuit is being used, the secondary circuit shall be checked

for the presence of refrigerant;

- Marking to the equipment continues to be visible and legible. Markings and signs that

are illegible shall be corrected;

- Refrigerating pipe or components are installed in a position where they are unlikely to

be exposed to any substance which may corrode refrigerant containing components,

unless the components are constructed of materials which are inherently resistant to

being corroded or are suitably protected against being so corroded.

6-9 Checks to electrical devices

Repair and maintenance to electrical components shall include initial safety checks and

component inspection procedures. If a fault exists that could compromise safety, then

no electrical supply shall be connected to the circuit until it is satisfactory dealt with. if

the fault cannot be corrected immediately but it is necessary to continue operation, an

adequate temporary solution shall be used. This shall be reported to the owner of the

equipment so all parts are advised. Initial safety checks shall include:

- That capacitors are discharged: this shall be done in a safe manner to avoid possibility

of sparking;

- That there no live electrical components and wiring are exposed while charging,

recovering or purging the system;

- That there is continuity of earth bonding.

7. Repairs to sealed components

During repairs to sealed components, all electrical supplies shall be disconnected from

the equipment being worked upon prior to any removal of sealed electrical supply to

equipment during servicing, then a permanently operating form of leak detection shall be

located at the most critical point to warn of a potentially hazardous situation. Particular

attention shall be paid to the following to ensure that by working on coelectrical

components. The casing is not altered in such a way that the level of protection is

affected. This shall include damage to cables, excessive number of connections, terminals

not made to original specification, damage to seals, incorrect fitting of glands, etc.

Ensure that apparatus is mounted securely. Ensure that seals or sealing materials

have not degraded such that they no longer serve the purpose of preventing the

ingress of flammable atmospheres. Replacement parts shall be in accordance with the

manufacturer’s specifications.

NOTE:

The use of silicon sealant may inhibit the effectiveness of some types of leak detection

equipment. Intrinsically safe components do not have to be isolated prior to working on them.

8. Repair to intrinsically safe components

-10-

SAFETY INSTRUCTIONS

Do not apply any permanent inductive or capacitance loads to the circuit without ensuring

that this will not exceed the permissible voltage and current permitted for the equipment

in use. Intrinsically safe components are the only types that can be worked on whilelive in

the presence of a flammable atmosphere. The test apparatus shall be at the correct rating.

Replace components onlywith parts specified by the manufacturer. Other parts may result

in the ignition of refrigerant atmosphere from a leak.

9. Cabling

Check that cabling will not be subject to wear, corrosion, excessive pressure, vibration, sharp

edges or any other adverse environmental effects.The check shall also take into account the

effects of aging or continual vibration from sources such as compressors or fans.

10. Detection of flammable refrigerants

Under no circumstances shall potential sources of ignition be used in the searching for or

detection of refrigerant leaks. A halide torch (or any other detector using a naked flame)

shall not be used.

10. Leak detection methods

The following leak detection methods are deemed acceptable for systems containing

flammable refrigerants:

- Electronic leak detectors shall be used to detect flammable refrigerants, but the

sensitivity may not be adequate, or may need re-calibration (Detection equipment shall

be calibrated in a refrigerant-free area.)

- Ensure that the detector is not a potential source of ignition and is suitable for the

refrigerant used.

- Leak detection equipment shall be set at a percentage of the LFL of the refrigerant and

shall be calibrated to the refrigerant employed and the appropriate percentage of gas

(25% maximum) is confirmed.

- Leak detection fluids are also suitable for use with most refrigerants but the use of

detergents containing chlorine shall be avoided as the chlorine may react with the

refrigerant and corrode the copper pipe-work.

- If a leak is suspected, all naked flames shall be removed/ extinguished.

- If a leakage of refrigerant is found which requires brazing, all of the refrigerant shall

be recovered from the system, or isolated (by means of shut off valves) in a part of the

system remote from the leak.

11. Removal and evacuation

- When breaking into the refrigerant circuit to make repairs - or for any other purpose

conventional procedures shall be used. However, it is important that best practice is

followed since flammability is a consideration.

The following procedure shall be adhered to:

- Remove refrigerant;

- Purge the circuit with inert gas;

- Evacuate;

- Purge with inert gas;

- Open the circuit by cutting or brazing.

The refrigerant charge shall be recovered into the correct recovery cylinders.The system

shall be purged with OFN to render the appliance safe for flammable refrigerants. This

process may need to be repeated several times. Compressed air or oxygen shall not be

-11-

SAFETY INSTRUCTIONS

used for this task. Purging shall be achieved by breaking to fill until the working pressure is

achieved, then venting to atmosphere, and finally pulling down to a vacuum. This process

shall be repeated until no refrigerant is within the system. When the final charge is used,

the system shall be vented down to atmospheric pressure to enable work. This operation

is absolutely vital if brazing operations, on the pipe-work are to take place. Ensure that the

outlet for the vacuum pump is not close to any potential ignition sources and there is the

vacuum in the system with OFN and continuing ventilation available.

12. Charging procedures

In addition to conventional charging procedures, the following requirements shall be followed:

- Ensure that contamination of different refrigerants does not occur when using charging

equipment.

- Hoses or lines shall be as short as possible to minimize the amount of refrigerant

contained in them.

- Cylinders shall be kept in an appropriate position according to the instructions.

- Ensure that the refrigerating system is earthed prior to charging the system with

refrigerant.

- Label the system when charging is complete (if not already).

- Extreme care shall be taken not to overfill the refrigerating system. Prior to recharging the

system it shall be pressure tested with OFN.

The system shall be leak tested on completion of charging but prior to commissioning.

A follow up leak test shall be carried out prior to leaving the site.

13. Decommissioning

Before carrying out this procedure, it is essential that the technician is completely familiar

with the equipment and all its detail. It is recommended good practice that all refrigerants

are recovered safely. Prior to the task being carried out, an oil and refrigerant sample shall

be taken in case analysis is required prior to re-use of recovered refrigerant. It is essential

that electrical power is available before the task is commenced.

a. Become familiar with the equipment and its operation.

b. Isolate system electrically.

c. Before attempting the procedure ensure that:

- Mechanical handling equipment is available, if required, for handling refrigerant

cylinders;

- All personal protective equipment is available and being used correctly;

- The recovery process is supervised at all times by a competent person;

- Recovery equipment and cylinders conform to the appropriate standards.

d. Pump down refrigerant system, if possible.

e. If a vacuum is not possible, make a manifold so that refrigerant can be removed from

various parts of the system.

f. Make sure that cylinder is situated on the scales before recovery takes place.

g. Start the recovery machine and operate in accordance with instructions.

h. Do not overfill cylinders. (No more than 80 % volume liquid charge).

i. Do not exceed the maximum working pressure of the cylinder, even temporarily.

j. When the cylinders have been filled correctly and the process completed, make sure that

the cylinders and the equipment are removed from site promptly and all isolation valves

-12-

SAFETY INSTRUCTIONS

on the equipment are closed off.

k. Recovered refrigerant shall not be charged into another refrigerating system unless it

has been cleaned and checked.

14. Labelling

Equipment shall be labelled stating that it has been de-commissioned and emptied

of refrigerant. The label shall be dated and signed. Ensure that there are labels on the

equipment stating the equipment contains flammable refrigerant.

15. Recovery

When removing refrigerant from a system, either for servicing or decommissioning, it is

recommended good practice that all refrigerants are removed safely. When transferring

refrigerant into cylinders, ensure that only appropriate refrigerant recovery cylinders are

employed. Ensure that the correct number of cylinders for holding the total system charge

is available. All cylinders to be used are designated for the recovered refrigerant and

labelled for that refrigerant (i.e. special cylinders for the recovery of refrigerant). Cylinders

shall be complete with pressure relief valve and associated shutoff valves in good working

order. Empty recovery cylinders are evacuated and, if possible, cooled before recovery

occurs. The recovery equipment shall be in good working order with a set of instructions

concerning the equipment that is at hand and shall be suitable for the recovery of

flammable refrigerants. In addition, a set of calibrated weighing scales shall be available and

in good working order. Hoses shall be complete with leak free disconnect couplings and in

good condition. Before using the recovery machine, check that it is in satisfactory working

order, has been properly maintained and that any associated electrical components are

sealed to prevent ignition in the event of a refrigerant release. Consult manufacturer if in

doubt. The recovered refrigerant shall be returned to the refrigerant supplier in the correct

recovery cylinder, and the relevant Waste Transfer Note arranged. Do not mix refrigerants

in recovery units and especially not in cylinders. If compressors or compressor oils are to be

removed, ensure that they have been evacuated to an acceptable level to make certain that

flammable refrigerant does not remain within the lubricant. The evacuation process shall be

carried out prior to returning the compressor to the suppliers. Only electric heating to the

compressor body shall be employed to accelerate this process. When oil is drained from a

system, it shall be carried out safely. When moving or relocating the air conditioner, consult

experienced service technicians for disconnection and reinstallation of the unit. Do not

place any other electrical products or household belongings under indoor unit or outdoor

unit. Condensation dripping from the unit might get them wet, and may cause damage

or malfunction of your property. To keep ventilation openings clear of obstruction. The

appliance shall be stored in a well-ventilated area where the room size corresponds

to the room area as specified for operation. The appliance shall be stored in a room without

continuously operating open flames (for example an operating gas appliance) and ignition

sources (for example an operating electric heater). Reusable mechanical connectors and

flared joints are not allowed.

-13-

User Interface

Start to use your air conditioner

1. Press the power button to start or stop the

operation of your appliance.

2. Press the mode button to select the

operation mode in sequence of Cool Dry,

Fan or Heat.

3. Press the temperature adjustment button to

set the desired temperature.

4. Press the FAN button to choose the desired

fan speed in sequence of High, Mid or Low.

Filter Reset

1. When the Filter Reset indicator light is lit,

remove, clean and replace the air filter. See

“Cleaning the Air Filter“.

2. Press and release FILTER button after

replacing the air filter.

NOTE: After 360 hours of fan operating time,

the Filter indicatorlight will turn on. It will

remain on for 180 hours or until you press

FILTER button.

After 180 hours, it will turn off automatically.

IMPORTANT NOTE:

* When the air conditioner is turned on for the first time

after it’s plugged in, it will run in the 6th Sense Mode.

* The air conditioner display shows the setting

temperature.

Only on standby mode, the display shows the ambient

temperature.

* When changing modes while the air conditioner is

operating, the compressor will stop for 3 to 5 minutes

before restarting.

If a button is pressed during this time, the compressor

will not restart for another 3 to 5 minutes.

* In Cooling or Dry mode, the compressor and

condenser fan will stop when the room temperature

reaches the set temperature

* In Fan Only mode, the temperature can NOT be set.

* Heating is NOT available for Cooling only air

conditioner.

* Below operation modes can only be set by remote

controller.

* In the event of a power failure, your air conditioner will

operate at the previous settings when the power is

restored.

* If the unit is operating in UNLIKELY VERY HUMIDITY

environment, water will be collected in the tank inside

the unit. The air conditioner will stop once the water

tank is full, and the screen will display “E5” to inform

you to empty the internal container. There is a plasic

tube at the back of the appliance, move the appliance

to a safe place, lay down the plastic tube for water

drain.

-14-

Remote controller

Insert the batteries into RC

1. Insert a pin and gently press down on the battery

cover and push in the direction of the arrow to

remove, as shown.

2. Insert 2 AAA batteries (1.5V) into the compartment.

Ensure that “+” and “-” polarity is correctly positioned.

3. Close the battery cover on the remote control.

• Remote Control presetting

Each time the batteries are replaced in the remote

controller, the remote controller pre-set at Heat Pump

mode. The heat pump AC remote controller can be used

to control the cool only AC models.

• The remote control will operate the air conditioner at a

distance of up to 7m.

Use RC to control the appliance

• To operate the appliance by remote control, point the

remote control at the receiving device on the indoor

unit, to ensure receiving sensibility.

• To send a message from remote control, the symbol

will flash for 1 second. On receipt of the message, the

appliance will emit a beep.

Note: please follow the intruction which matches to the remote controller you receive for Air Conditioner

operation.

Function description of buttons

1.

ON OFF BUTTON

Starts and/or Stops the appliance by pressing this button.

2. MODE BUTTON

Used to select the operation mode.

3. FAN BUTTON

Used to select fan speed in sequence auto, high, medium or low.

4-5. TEMPERATURE BUTTON

Used to select the room temperature. Used to set time in timer mode and real

time clock.

6. 6th SENSE BUTTON

Sets or cancels 6th Sense operation.In this mode,temperature and fan speed are

automatically set based on the actual room temperature.

7. SWING BUTTON

Stops or starts horizontal adjustment louver swinging and sets the

desired up/down airflow direction.

8. SLEEP BUTTON

1) Short press,sets or cancels Sleep Mode operation.Sleep Mode can be set in Cooling

Heating or Dry operation mode,this function gives you a more comfortable

environment for sleep.

2) Long press,press 3 senconds to turn on or turn off display light on unit.

9. AROUND U BUTTON

Used to start or cancel Around U function.When you press this button,remote control

transmits the actual room temperature around it to the indoor unit,and the appliance

will operate according this temperature to let you feel more comfortable.

10. TIMER BUTTON

Used to set or cancel the timer on operation.

Used to set or cancel the timer off operation.

11. SILENT BUTTON

Used to set or cancel the Silent operation.Press silent button to let the unit operate at low noise level to get quiet and

comfortable room environment.

Note:Under extreme environmental conditions,it is possible to notice a temporary slight increase in noise due to the need of reaching the comfort

temperature quickly.

Symbols on RC display

Cooling indicator Auto fan speed 6th Sense indicator Signal transmission

Dry indicator High fan speed Sleep indicator Display set timer

Fan only indicator Medium fan speed Around U indicator Display set temperature

Heating indicator Low fan speed Silent indicator

Signal receptor

-15-

Maintenance

Draining the Air Conditioner

(Please connect the drain hose on heating mode,otherwise

the unit will stop running after reachs warning level.)

1. Press ON/OFF to turn off the air conditioner.

2. Unplug air conditioner or disconnect power.

3. Move the appliance gently and stably to a draining

location or outside to drain water. Do not move the unit

before water is drained out completely.

4. Remove the secondary drain plug and drain water

completely.

5. Remove the primary drain hose from the hose clip.

Remove the drain hose plug from the end of the primary

drain hose and drain water completely.

NOTE: If air conditioner will be stored after use, see “Storing

After Use“.

6. Reinstall the drain hose plug and the secondary drain

plug.

7. Reattach the primary drain hose to the drain hose clip.

8. Reposition the air conditioner.

9. Plug in air conditioner or reconnect power.

10. Press ON/OFF to start the air conditioner.

Cleaning the Air Filter

1. Press ON/OFF to turn off the air conditioner.

2. Open the filter panel door on the back of the air

conditioner and remove it.

3. Remove the air filter from the filter panel door.

4. Use a vacuum cleaner to clean the filter. If filter is very

dirty, wash filter in warm water with a mild detergent.

NOTE: Do not wash filter in the dishwasher or use any

chemical cleaners.

5. Air dry filter completely before replacing to ensure

maximum efficiency.

6. Reattach the air filter to the filter panel door.

7. Reinstall filter panel door.

8. Press ON/OFF to start the air conditioner.

Cleaning the Outside

1. Unplug air conditioner or disconnect from power.

2. Remove the air filter and clean separately.

See“Cleaning the Air Filter.”

3. Wipe outside of the air conditioner with a soft, damp

cloth.

4. Plug in air conditioner or reconnect power.

5. Press ON/OFF to start the air conditioner.

Disposal of the batteries

To protect natural resources and to promote material reuse, please separate batteries from other types of waste and

recycle them through your local, free battery return system.

Storing After Use

1. Drain the water (see the “Draining the Air

Conditioner”)

2. Run the air conditioner set to Fan Only for

approximately 12 hours to dry the air conditioner.

3. Unplug air conditioner.

4. Remove flexible exhaust hose and store with air

conditioner in a clean, dry area. See “Installation

Instructions.”

5. Remove window kit and store with air conditioner

in a clean, dry area. See “Installation Instructions.”

6. Remove the filter and clean. See “Cleaning the Air

Filter.”

7. Clean the outside of air conditioner. See “Cleaning

the Outside.”

8. Reinstall filter.

9. Remove the batteries and store the remote control

with air conditioner in a clean, dry area.

A. Secondary drain plug

B. Drain hose plug

A. Filter panel door

B. Air filter

-16-

Installation instruction

Tools and Parts

Gather the required tools and parts before starting

installation. Read and follow the instructions provided

with any tools listed here.

1. Tools needed

• Phillips screwdriver

• Saw

• Cordless drill and 1/8” bit

• Scissors

• Pencil

2. Parts Supplied

The company provides only one plan to install local air

conditioner. See “Install local Air Conditioner”.

Location Requirements

NOTES:

• The flexible exhaust hose allows placement of the air

conditioner between 23 1/2” and 67” (60 cm and 170 cm) from

window or door.

The appliance with supplementary heater needs to keep a

minimum distance of 100 cm from the combustible surfaces.

The appliance shall be installed,operated and stored in a room

which floor area larger than 14.5 m² and higher than 2.2 m.

Local air conditioners are designed as supplemental cooling

to local areas within a room.

• To ensure proper ventilation, keep the required distance from

the return air outlet to the wall or other obstacles at least

23 1/2” (60 cm).

• Do not block air outlet.

• Provide easy access to grounded outlet.

Electrical Requirements

• The local air conditioner should be connected to a

220-240V / 50Hz, 20-amp fused grounded outlet.

• The use of a time-delay fuse or time-delay circuit breaker is

recommended.

• All wiring must comply with local and national electrical

regulations and be installed by a qualified electrician.

If you have any questions, contact a qualified electrician.

Use your power supply cord:

Plug power supply cord into a grounded outlet.

NOTES:

• A damaged power supply cord must be replaced with a new

power supply cord obtained from the product manufacturer

and must not be repaired.

• Working temperature of Cooling 21°C- 35°C

Working temperature of Heating 7°C-27°C

For detail installation information, please download from: docs.whirlpool.eu

A. Flexible exhaust hose

B. Window exhaust adapter

C. Outer slider section

D. Rain Cover

E. Inner slider section

Vertical

Silde Window

Horizontal

Silde Window

combustible surfaces

100 cm

60 cm - 170 cm

combustible surfaces

100 cm

60 cm - 170 cm

-17-

Troubleshooting

Operation problems are often due to minor causes, please check and refer to the following chart before

contacting the service. This may save time and unnecessary expenses.

Trouble Analysis

Air conditioner does

not operate

• The power supply cord is unplugged. Plug into a grounded outlet. See “Electrical Requirements.”

• A household fuse has blown, or a circuit breaker has tripped. Replace the fuse, or reset the circuit

breaker. See “Electrical Requirements.”

• The On/Off button has not been pressed. Press ON/OFF.

• The local power has failed. Wait for power to be restored.

• Time-delay fuse or circuit breaker of the wrong capacity is being used. Replace with a time delay

fuse or circuit breaker of the correct capacity. See “Electrical Requirements.”

Air conditioner blows

fuses or trips circuit

breakers

• Too many appliances are being used on the same circuit. Unplug or relocate appliances that share

the same circuit.

• You are trying to restart the air conditioner too soon after turning off air conditioner. Wait at least

3 minutes after turning off air conditioner before trying to restart it.

• You have changed modes. Wait at least 3 minutes after turning off air conditioner before trying to

restart the appliance.

Air conditioner seems

to run too much

• Is there a door or window open? Keep doors and windows closed.

• In cooling mode: the air conditioner is in a heavily occupied room, or heat producing appliances

are in use in the room. Use exhaust vent fans while cooking or bathing and try not to use heat

producing appliances during the hottest part of the day. Local air conditioners are designed

as supplemental cooling to local areas within a room. A higher capacity air conditioner may be

required, depending on the size of the room being cooled.

• In heating mode: the air conditioner is in a very cool room. Local air conditioners are designed

as supplemental heating to local areas within a room. A higher capacity air conditioner may be

required, depending on the size of the room being heated up.

Air conditioner runs for

a short time only, but

room is not cool or hot

• Set temperature is close to room temperature. Lower or Higher set temperature.

See “Operating mode description”.

Display error code • If the unit display error code E5, it is water full in the unit, you should drain the water,

see “Draining the air conditioner”. After draining, you can operate the unit.

• If the unit display error code EI/E2/E3/E6/E7/EA, please contact customer service.

Air conditioner runs,

but does not cool/hot

• The filter is dirty or obstructed by debris. Clean the filter.

• Air outlet is blocked. Clear air outlet.

• The setting temperature is not compatible. In cooling mode: set temperature is too high.

Lower set temperature. In heating mode: set temperature is too low. Higher set temperature

Air conditioner cycles

on and off too much

• The air conditioner is not properly sized for your room. Check the cooling/heating capabilities of

your local air conditioner. Local air conditioners are designed as supplemental cooling/heating to

local areas within a room.

• The filter is dirty or obstructed by debris. Clean the filter.

• In cooling mode there is excessive heat or moisture (open container cooking, showers,

etc.) in the room. Use a fan to exhaust heat or moisture from the room. Try not to use heat-

producing appliances during the hottest part of the day. In heating mode the temperature

of the environment is too high. Do not use your air conditioner when the temperature of the

environment is too high.

• The louvers are blocked. Install the air conditioner in a location where the louvers are free from

curtains, blinds, furniture, etc.

• The outside temperature is below 18°C. Do not try to operate your air conditioner in the cooling

mode when the outside temperature is below I8°C.

Note: If the problems still have, turn off the appliance and disconnect from power supply, then contact the

nearest Whirlpool Authorized Service Center. Do not attempt to move, repair, disassemble, or modify the

appliance by yourself.

-18-

AFTER SALES SERVICE

Before contacting the Customer Care Centre:

1. Try to solve the problem yourself based on the

descriptions given in the “Troubleshooting”.

2. Turn the appliance off and restart it to see if the fault

persists.

If after carrying out the above checks, the fault

persists, contact the Customer Care Centre.

Please give:

• a short description of the fault;

• the exact model of the air conditioner;

• the service number (this is the number found below

the word Service on service sticker which is located on

the side or on the bottom of the indoor unit).

• The service number can also be found in the warranty

booklet;

• your full address;

• your telephone number.

If repair work has to be carried out, contact the

Customer Care Centre (Use of original spare parts and a

proper repair is guarenteed).

You will need to present the original invoice.

Failure to comply with these instructions could

compromise the safety and quality of your product.

Note: if you want the full manual for your appliance, please help to download it from websit throught below

link: docs.whirlpool.eu using QR code

Whirlpool EMEA

Via Pisacane 1

20016 PERO (MI) ITALY

-19-

SICHERHEITSHINWEISE

DIESE MUSS GELESEN UND BEACHTET WERDEN

• Laden Sie die komplette Bedienungsanleitung auf docs.whirlpool.eu runter oder rufen

Sie die Telefonnummer auf dem Garantieheft an.

• Diese Sicherheitsanweisungen vor dem Gebrauch durchlesen. Diese Anweisungen zum

Nachschlagen leicht zugänglich aufbewahren.

• In diesen Anweisungen sowie auf dem Gerät selbst werden wichtige

Sicherheitshinweise angegeben, die durchgelesen und stets beachtet werden

müssen. Der Hersteller übernimmt keine Haftung für die Nichtbeachtung dieser

Sicherheitshinweise, für unsachgemäße Verwendung des Geräts oder falsche

Bedienungseinstellung.

•

Das Gerät verwendet ein entzündliches Kältemittel (R290), die maximale Füllmenge

für das Kältemittel beträgt 0,3kg. Das Gerät sollte in einem Raum mit einer Grundfläche

von mehr als 14.5m

2

installiert, betrieben und gelagert werden. Zudem sollte der Raum

höher als 2,2 m sein.

Das Gerät wurde im verfügbaren externen statischen Druckbereich von 0,95 MPa -

1,05

MPa getestet.

•

Babys und Kleinkinder (0-3 Jahre) müssen vom Gerät ferngehalten werden. Jüngere

Kinder (3-8

Jahre) müssen vom Gerät ferngehalten werden, es sei denn, sie werden

ständig beaufsichtigt. Dieses Gerät darf von Kindern ab 8

Jahren sowie Personen mit

herabgesetzten physischen, sensorischen oder geistigen Fähigkeiten und Mangel an

Erfahrung und Kenntnissen nur unter Aufsicht oder nach ausreichender Einweisung

durch eine für ihre Sicherheit verantwortliche Person verwendet werden. Kinder dürfen

nicht mit dem Gerät spielen. Die Reinigung und Pflege des Gerätes darf von Kindern

nicht ohne Aufsicht durchgeführt werden.

ZUGELASSENE VERWENDUNG

•

VORSICHT Das Gerät ist nicht für den Betrieb mit einem externen Schalter, wie

Timer, oder separatem Fernbedienungssystem konstruiert.

•

Dieses Gerät ist für Haushaltsanwendungen und ähnliche Anwendungen konzipiert,

zum Beispiel: Hotels und Büros.

•

Dieses Gerät eignet sich nicht für den professionellen Einsatz.

•

Schalten Sie das Klimagerät immer erst über die Fernbedienung oder die POWER-

Taste am Bedienfeld des Geräts aus.

Schalten Sie dazu nicht den Leitungsschutzschalter aus und ziehen Sie nicht den

Stecker aus der Steckdose.

Trennen Sie das Klimagerät vor einem längeren Nichtgebrauch und bei Gewitter/Sturm

vom Stromnetz.

-20-

SICHERHEITSHINWEISE

Stecken Sie keine Gegenstände in den Luftauslass der Außeneinheit -

Verletzungsgefahr. Die Lüftungsöffnungen dürfen nicht behindert werden.

INSTALLATION

•

Zum Transport und zur Installation des Gerätes sind zwei oder mehrere Personen

erforderlich - Verletzungsgefahr. Schutzhandschuhe zum Auspacken und zur

Installation verwenden - Risiko von Schnittverletzungen.

•

Die Installation, einschließlich elektrischer Anschlüsse und Reparaturen

müssen von einem qualifizierten Techniker entsprechend den vor Ort geltenden

Sicherheitsvorschriften durchgeführt werden.

Das Gerät nicht selbst reparieren und tauschen keine Teile austauschen, wenn dies von

der Bedienungsanleitung nicht ausdrücklich vorgesehen ist.

Kinder vom Installationsort fern halten. Prüfen Sie das Gerät nach dem Auspacken auf

Transportschäden.

Bei auftretenden Problemen wenden Sie sich bitte an Ihren Händler oder den

Kundendienst.

Nach der Installation müssen Verpackungsabfälle (Kunststoff, Styroporteile usw.)

außerhalb der Reichweite von Kindern aufbewahrt werden - Erstickungsgefahr.

Das Gerät vor Installationsarbeiten von der netzfernen Stromversorgung trennen -

Stromschlaggefahr.

Während der Installation sicherstellen, das Netzkabel nicht mit dem Gerät selbst

zu beschädigen - Brand- oder Stromschlaggefahr. Das Gerät erst starten, wenn die

Installationsarbeiten abgeschlossen sind.

Dank des flexiblen Abluftschlauchs kann das Klimagerät in einer Entfernung von

23” und 67” (60 cm und 170 cm) vom Fenster oder der Tür aufgestellt werden. Bei einem

Gerät mit Zusatzheizung muss ein Mindestabstand von 100 cm von der entzündlichen

Oberfläche eingehalten werden.

•

Betreiben Sie das Klimagerät nicht in einem Nassraum wie Badezimmer oder

Waschküche.

•

Vor dem Umsetzen des Geräts das Netzkabel abziehen.

Pagina se încarcă ...

Whirlpool Climatiseur Mobile Monobloc 3500w 35m² - PAC W212 CO Manualul proprietarului

Whirlpool Climatiseur Mobile Monobloc 3500w 35m² - PAC W212 CO Manualul proprietarului

în alte limbi

Lucrări conexe

Alte documente