Mellanox Technologies SX6518 Hardware Installation Manual

www.mellanox.com

324-Port InfiniBand FDR SwitchX®

Switch Platform Hardware Installation Guide

PN:SX6518-NR, SX6518-6R

Rev 1.

3

Document Number: 3805

Mellanox Technologies

2

InfiniBand Switch Platform Hardware User Manual

Mellanox Technologies

3

Table of Contents

List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Chapter 1 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

1.1 Installation Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

1.2 Environmental and Safety Recommendations . . . . . . . . . . . . . . . . . . . . 15

1.3 Chassis Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

1.4 Leaf Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

1.5 Spine Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

1.6 Management Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

1.7 Physical Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

1.7.1 Starting with the Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

1.7.2 ESD Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

1.7.3 Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

1.7.4 Installing the Cable Holder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

1.7.5 Ground Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

1.8 Power Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

1.8.1 Powering Up the Switch Platform. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

1.9 InfiniBand QSFP Cable Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

1.9.1 Supported Approved Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

1.9.2 Cable Power Classes. . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . 42

1.10 Hot Swap Insertion and Extraction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

1.10.1 Power Supply Units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

1.10.2 Leaf Boards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

1.10.3 Spine Boards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

1.10.4 Fan Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

1.10.5 Management Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

1.10.6 Switch Shut-Down Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Chapter 2 Interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

2.1 LED Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

2.1.1 Power Supply Unit LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

2.1.2 Leaf Board LED Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

2.1.3 Spine Board LED Indicators. . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . 61

2.1.4 Spine Side Panel Display LED Indicators . . . .

. . . . . . . . . . . . . . . . . . . . 63

2.1.5 Management Module LED Indicators. .

. . . . . . . . . . . . . . . . . . . . . . . . . . 64

2.1.6 Port Connector Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

2.2 Air Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

2.3 QSFP Cable Power Budget Classification. . . . . . . . . . . . . . . . . . . . . . . . 67

2.4 Management Module Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

2.4.1 I2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

2.4.2 CONSOLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

2.4.3 MGT– Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

InfiniBand Switch Platform Hardware User Manual

Mellanox Technologies

4

2.4.4 USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

2.4.5 Reset – RST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Chapter 3 Chassis Power Up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

3.1 Power Supply and Spine Board Indicator Status at Power ON. . . . . . . . 70

Chapter 4 First-Time Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

4.1 Running the Wizard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

4.2 Re-Running the Wizard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

4.3 Starting the Command Line (CLI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

4.4 Starting the Web User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Chapter 5 Resetting the Switch – RST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Chapter 6 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

6.1 Power Supply Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

6.2 Leaf Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

6.3 Management Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

6.4 Spine Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

6.5 MLNX-OS® Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Chapter 7 Disassembly and Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

7.1 Disassembling the Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

7.1.1 Removing the Chassis. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

7.1.2 Removing the Bottom Shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

7.2 Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Appendix A Installation Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

A.1 Installation Safety Warnings (English) . . . . . . . . . . . . . . . . . . . . . . . . 86

A.2 安裝安全性警告 (Chinese) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

A.3 Avertissements de sécurité pour l'installation (French) . . . . . . . . . . . 95

A.4 Installation Sicherheitshinweise(German). . . . . . . . . . . . . . . . . . . . . 100

A.5 Advertencias de seguridad de instalación (Spanish) . . . . . . . . . . . . 104

A.6 Предупреждения по технике безопасности при установке (Russian) 108

A.7 Avertismente privind siguranţa la instalare (Romanian) . . . . . . . . . . 112

A.8 Sigurnosna upozorenja za instaliranje (Croatian). . . . . . . . . . . . . . . 117

InfiniBand Switch Platform Hardware User Manual

Mellanox Technologies

5

List of Tables

Table 1: Revision History of this Installation Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Table 2: Reference Documents and Websites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Table 3: Leaf Status LED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Table 4: Bad Port LED Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Table 5: Connector Physical and Logical Link Indications

. . . . . . . . . . . . . . . . . . . . . . . . 60

Table 6: Spine Status LED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Table 7: Spine Fan Status LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Table 8: Spine to Leaf IB Link Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Table 9: Bad Port LED Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Table 10: LEDs Display for Normal Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Table 11: LEDs Display for Normal Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Table 12: Management Module PSU LED Configurations . . . . . . . . . . . . . . . . . . . . . . . . 65

Table 13: Management Module S.Fan LED Configurations . . . . . . . . . . . . . . . . . . . . . . . 66

Table 14: Management Module L.Fan LED Configurations . . . . . . . . . . . . . . . . . . . . . . . 66

Table 15: Management Module MASTER LED Configurations . . . . . . . . . . . . . . . . . . . . 66

Table 16: Serial Terminal Program Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Table 17: Configuration Wizard Session - IP Configuration by DHCP. . . . . . . . . . . . . . . . 72

Table 18: Configuration Wizard Session - IP Zeroconf Configuration

. . . . . . . . . . . . . . . . 74

Table 19: Configuration Wizard Session - St

atic IP Configuration. . . . . . . . . . . . . . . . . . . 75

InfiniBand Switch Platform Hardware User Manual

Mellanox Technologies

6

List of Figures

Figure 1: Distance Between the Vertical Supports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Figure 2: Installation Kit Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Figure 3: Shock and Tilt Stickers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Figure 4: Container Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Figure 5: Vertical Rack Supports Dimension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Figure 6: Placement of Chassis in Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Figure 7: Adjustable Shelf Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Figure 8: Top of Shelf Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Figure 9: Placing the Shelf Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Figure 10: Caged Nut Locations for the Shelf Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Figure 11: Shelf Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Figure 12: U Numbering Above Shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Figure 13: Putting the Chassis in the Rack Using a Fork Lift . . . . . . . . . . . . . . . . . . . . . . . 28

Figure 14: Putting the Chassis in the Rack Using a Mechanical Lift . . . . . . . . . . . . . . . . . 29

Figure 15: Place the Upper Bracket Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Figure 16: Attach the Shelf Extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Figure 17: Caged Nut Placement by U Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Figure 18: Location for the Lock-Down Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Figure 19: Fork Lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Figure 20: Mechanical Lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Figure 21: Face Plate Mounting Bolt Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Figure 22: Upper Bracket Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Figure 23: Upper Brackets and Offset Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Figure 24: Offset to Upper Bracket Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Figure 25: Location for the Lock-Down Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Figure 26: Lock-Down Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Figure 27: Lock-Down Bars Bolt and Washer Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Figure 28: Spine Side with Filler Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Figure 29: Cable Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Figure 30: Ground Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Figure 31: Multiple Power Inlets – Electric Caution Notification . . . . . . . . . . . . . . . . . . . . . 40

Figure 32: Spine Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Figure 33: Power Cord Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Figure 34: Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Figure 35: Leaf Board Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Figure 36: Ejector Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Figure 37: Leaf Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

InfiniBand Switch Platform Hardware User Manual

Mellanox Technologies

7

Figure 38: Intact vs Defected Signal Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Figure 39: Intact vs Defected Power Pin Holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Figure 40: Management Module Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Figure 41: Spine Board Extraction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Figure 42: Intact vs Defected Mechanics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Figure 43: Intact vs Defected Side Signal Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Figure 44: Intact vs Defected Middle Signal Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Figure 45: Intact vs Defected Power Pin Holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Figure 46: Spine Board Insertion Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Figure 47: Leaf Fan Locations on the Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Figure 48: Leaf Fan Module Extraction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Figure 49: Spine Fan Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Figure 50: Fan Status LED on the Spine Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Figure 51: Management Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Figure 52: Intact vs Defected Signal Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Figure 53: Intact vs Defected Power Pin Holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Figure 54: Power Supply Unit Status Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Figure 55: PSU Cover On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Figure 56: Leaf Board Led Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Figure 57: Spine Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Figure 58: Spine Side Panel Display Status Indications . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Figure 59: Management Module Status Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Figure 60: Management Module LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Figure 61: Port Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Figure 62: Top and Bottom Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Figure 63: Management Module Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Figure 64: Reset Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Figure 65: Spine Side Panel Display Status Indications . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Figure 66: Management Module Status Indications for Normal Operation . . . . . . . . . . . . 70

Figure 67: Console Ports for SX60xx/SX65xx Managed Systems . . . . . . . . . . . . . . . . . . . 71

Figure 68: MLNX-OS Login Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Figure 69: EULA Prompt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Figure 70: Display After Login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Figure 71: Reset Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Figure 72: Mechanical Lifting Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

InfiniBand Switch Platform Hardware User Manual

Mellanox Technologies

8

Revision History

About this Manual

This manual provides installation and set-up instructions for the SX6518 QSFP Chassis

InfiniBand Switch Platform.

Intended Audience

This manual is intended for users and system administrators responsible for installing

and setting up the chassis platform.

The manual assumes familiarity with the InfiniBand

®

architecture specification.

Table 1 - Revision History of this Installation Guide

Revision Date Details

1.3 Feb. 2014 Rearranged document: Consolidated installation sections under Chapter 1,

“Installation,” on page 11; updated Chapter 1, “Overview,” on page 12; and

re-ordered sections).

Added:

• Figure 60, “Management Module LEDs,” on page 65

Updated:

• Section 1.4, “Power Supply Redundancy,” on page 15

• Section 1.7.3.5, “Installing the Shelf,” on page 23

• Section 1.7.4, “Installing the Cable Holder,” on page 37

• FDR note in Section 1.9, “InfiniBand QSFP Cable Installation,” on page 41

• Section 1.10, “Hot Swap Insertion and Extraction,” on page 42

• Section 7.1, “Disassembling the Chassis,” on page 84

• Appendix A, “Installation Safety Warnings,” on page 86

1.2 May 2013

• Changed the Installation kit to include the top and bottom filler panels

• Made changes regarding N+N

• Added note N+N only works for 220V inputs

• Added shelf to cable management system

• Changed Figure #1

• Changed Figure #11

• Fixed parts list

1.1 August 2012

• Added use of 10mm socket to tighten upper brackets

• New copyright page

1.1 August 2012

• Added use of 10mm socket to tighten upper brackets

• New copyright page

1.0 March 2012 First release

InfiniBand Switch Platform Hardware User Manual

Mellanox Technologies

9

Related Documentation

The documentation set accompanying the QSFP Chassis InfiniBand Switch platform

includes the following:

Conventions

Throughout this manual, the name SX6518 and the terms chassis and switch are used to

describe the 324 port QSFP InfiniBand chassis, unless explicitly indicated otherwise.

The following icons are used throughout this document to indicat

e information that is

important to the user.

Table 2 - Reference Documents and Websites

Document Name Description

InfiniBand Architecture Specification,

Vol. 1, Release 1.2.1

The InfiniBand Architecture Specification that is provided by

IBTA

Switch Product Release Notes For possible hardware issues see the switch support product

page.

This requires a customer support login. Look up the rele-

vant SwitchX®-based switch system/se

ries release note file.

Mellanox MLNX-OS® User Manual

for

VPI

This document contains information regarding configuring and

managing Mellanox Technologies SwitchX® switch platforms

listing all of the commands available through MLNX-OS with

explanations and examples.

This symbol makes recommendations to the user.

This symbol indicates information that is helpful to the user.

This symbol indicates a situation that can potentially cause damage to hardware or

software.

Warning! This symbol indicates a situation that can potentially cause personal injury

and / or damage to hardware or software.

InfiniBand Switch Platform Hardware User Manual

Mellanox Technologies

10

Mellanox Part Numbering Legend

Place Field Decoder

M Mellanox Technologies

SX System Type SwitchX® Switch

PR Data Transfer Protocol (1, 2, 3, 4) = Ethernet (5, 6, 7, 8) = InfiniBand

G Module Generation 5, 6, 7, 8

FF Number of leafs 36, 18, 12, 06

C Data Rate B = 40Gb/s Ethernet

F = FDR, T = FDR10, Q = QDR, D = DDR

- Separator

P # Power Supplies N = N+N redundant

1=1PSU, 2=2PSUs, ...

R Chip Generation R – SwitchX®

S – SwitchX®-2

InfiniBand FDR Switch Platform Hardware User Manual

Mellanox Technologies

11

1Installation

Installation and initialization of the chassis is a simple process requiring attention to the

normal mechanical, power, and thermal precautions for rack-mounted equipment. Your

chassis comes only with the power supplies and fans pre-installed. The rest of the open-

ings are populated with blanks. All of the leafs, sp

ines, and management modules come

shipped in a separate package.

The chassis requires initial configuration

to get the chassis and Fabric management up

and running through remote management. See the Installation Guide that is packed in the

box for the instructions to make the initial configuration.

1.1 Installation Safety Warnings

These safety warnings are in English. For French, German, Spanish, Russian, and Roma-

nian see the Appendixes.

1. Installation Instructions

2. Bodily Injury Due to Weight

3. Heavy Equipment

This chassis can be installed in standard 19” racks that have depths between 65cm and

80cm between the vertical supports of the rack.

This unit is intended for installation in a Restricted Access Location. A restricted

access area can be accessed only through the use of a special tool, lock and key, or

other means of security.

Read all installation instructions before connecting the equipment to the power source.

Use enough people to safely lift this product.

This equipment is very heavy and should be moved using a mechanical lift to avoid

injuries.

<40 lbs

<18 kgs

40 - 70 lbs

18 - 32 kgs

70 - 121 lbs

32 - 55 kgs

>121 lbs

>55 kgs

InfiniBand FDR Switch Platform Hardware User Manual

Mellanox Technologies

12

4. Installation in Restricted Access Location

5. Risk of Electric Shock!

6. Over-temperature

7. Stacking the Chassis

8. Redundant Power Supply Connection - Electrical Hazard

9. Double Pole/Neutral Fusing

10. Multiple Power Inlets ,

This unit is intended for installation in a Restricted Access Location.

Risk of Electric Shock!

With the fan module removed power pins are accessible within the module cavity.

DO NOT insert tools or body parts into the fan module cavity.

This equipment should not be operated in an area with an ambient temperature exceed-

ing the maximum recommended: 45°C (113°F). Moreover, to guarantee proper air

flow, allow at least 8cm (3 inches) of clearance around the ventilation openings.

The chassis should not be stacked on any other equipment. If the chassis falls, it can

cause bodily injury and equipment damage.

This product includes a redundant power or a blank in its place. In case of a blank

power supply, do not operate the product with the blank cover removed or not securely

fastened.

This system has double pole/neutral fusing. Remove all power cords before opening

the cover of this product or touching any internal parts.

Risk of electric shock and energy hazard.

The PSUs are all independent.

Disconnect all power supplies to ensure a powered down state inside of the switch

platform.

InfiniBand FDR Switch Platform Hardware User Manual

Mellanox Technologies

13

11. During Lightning - Electrical Hazard

12. Copper InfiniBand Cable Connecting/Disconnecting

13. Rack Mounting and Servicing

14. Equipment Installation

15. Equipment Disposal

16. Local and National Electrical Codes

17. Installation Codes

During periods of lightning activity, do not work on the equipment or connect or dis-

connect cables.

Copper InfiniBand cables are heavy and not flexible, as such they should be carefully

attached to or detached from the connectors. Refer to the cable manufacturer for spe-

cial warnings/instructions.

When this product is mounted or serviced in a rack, special precautions must be taken

to ensure that the system remains stable. In general you should fill the rack with equip-

ment starting from the bottom to the top.

This equipment should be installed, replaced, and/or serviced only by trained and qual-

ified personnel.

Disposal of this equipment should be in accordance to all national laws and regula-

tions.

This equipment should be installed in compliance with local and national electrical

codes.

This device must be installed according to the latest version of the country

national electrical codes. For North America, equipment must be installed in

accordance to the applicable requirements in the US National Electrical Code

and the Canadian Electrical Code.

InfiniBand FDR Switch Platform Hardware User Manual

Mellanox Technologies

14

18. Battery Replacement

19. UL Listed and CSA Certified Power Supply Cord

20. High Leakage Current

21. Add GND connection information

22. Installation codes

23. Interconnection Of Units

Warning: Replace only with UL Recognized battery, certified for maximum

abnormal charging current not less than 4mA

There is a risk of explosion should the battery be replaced with a battery of an

incorrect type.

Dispose of used batteries according to the instructions.

For North American power connection, select a power supply cord that is UL Listed

and CSA Certified, 3 - conductor, [16 AWG], terminated with a molded plug rated at

125 V, [13 A], with a minimum length of 1.5m [six feet] but no longer than 4.5m.

For European connection, select a power supply cord that is internationally

harmonized and marked “<HAR>”, 3 - conductor, minimum 1.0 mm

2

wire,

rated at 300 V, with a PVC insulated jacket. The cord must have a molded plug

rated at 250 V, 10 A.

Warning: High leakage current; Earth connection essential before connecting supply.

Before connecting this device to the power line, the protective earth terminal screws of

this device must be connected to the protective earth in the building installation.

(GND Connection Information):

The building installation shall provide a means for a connection to protective earth;

and the equipment shall be permanently connected to that by a service person.

A SERVICE PERSON shall check whether or not the socket - outlet from which the

equipment is to be powered provides a connection to the building protective earth. If

not, the SERVICE PERSON shall arrange for the installation of a PROTECTIVE

EARTHING CONDUCTOR from the separate protective earthing terminal to the pro-

tective earth wire in the building. The equipment shall be installed in area where equi-

potential bonding exists ((such as a telecommunication centre or a dedicated computer

room).

This device must be installed according to the latest version of the country national

electrical codes. For North America, equipment must be installed in accordance to the

applicable requirements in the US National Electrical Code and the Canadian Electri-

cal Code.

Cables for connecting to the unit RS232 and Ethernet Interfaces must be UL

certified type DP-1 or DP-2. (Note- when residing in non LPS circuit)

Overcurrent Protection: A readily accessible Listed branch circuit overcurrent

protective device rated 20 A must be incorporated in the building wiring.

InfiniBand FDR Switch Platform Hardware User Manual

Mellanox Technologies

15

24. Hazardous Radiation Exposure

25. Proper Enclosure

26. Do Not Use the Switch as a Shelf or Work Space

27. WEEE Directive

28. Country of Norway Power Restrictions

1.2 Environmental and Safety Recommendations

The following are Mellanox recommendations.

Caution – Use of controls or adjustment or performance of procedures other

than those specified herein may result in hazardous radiation exposure.

CLASS 1 LASER PRODUCT and reference to the most recent laser standards

IEC 60 825-1:1993 + A1:1997 + A2:2001 and EN 60825-1:1994+A1:1996+

A2:2001

A suitable electrical, mechanical and fire enclosure shall be provided by the end prod-

uct manufacturer and or the end user.

Caution: Slide/rail mounted equipment is not to be used as a shelf or a work space. The

rails are not intended for sliding the unit away from the rack. It is for permanent instal-

lation at final resting place only, not used for service and maintenance

According to the WEEE Directive 2002/96/EC, all waste electrical and electronic

equipment (EEE) should be collected separately and not disposed of with regular

household waste.

Dispose of this product and all of its parts in a responsible and environmentally

friendly way.

This unit is intended for connection to a TN power system and an IT power system of

Norway only.

Recommended ambient temperature in the System room is 20

o

± 5

o

C.

Recommended humidity range is 40% ± 15% without condensing.

InfiniBand FDR Switch Platform Hardware User Manual

Mellanox Technologies

16

1.3 Chassis Package Contents

The package includes:

• 1 chassis with the following modules inst

alled:

•4 fans

• 6 PSUs

• 1 installation guide

•

1 box containing various other parts

• 1 installation kit box

• 1 box containing 6 power cords 250v 15a 2.0M, C14 to C13, USA UL Standard

• 1 cable management kit

Before you install your new SX6518 series chass

is, unpack the system and check to

make sure that all the parts have been sent, check this against the parts list. Check the

parts for visible damage that may have occurred during shipping.

It is highly recommended that the installation sites be as isolated as possible from all

sources of radio transmissions and electrical interference.

It is highly recommended that the installation site building be equipped with a light-

ning rod.

It is highly recommended that the installation site be equipped with smoke detectors

and a fire alarm warning system.

The system requires a KVA rated UPS system. It is recommended that a UPS system

be installed to protect the equipment in the event of unexpected power failure.

Make sure that the outlets and circuits will not be overloaded. Spread out the load over

at least two or three circuits or use a 3 phase circuit.

If anything is damaged or missing, contact your customer representative immediately.

InfiniBand FDR Switch Platform Hardware User Manual

Mellanox Technologies

17

1.4 Leaf Package Contents

The leafs are ordered by the customer and are shipped 4 to a box. The customer will

receive as many boxes as needed to fill the order.

1.5 Spine Package Contents

The spines are shipped 3 to a box. The customer will receive as many boxes as needed to

fill the chassis with a full complement of spines.

1.6 Management Package Contents

The package includes:

• all of the management modules ordered by the customer

•

1 RJ45 to DB9 harness for each management module received

1.7 Physical Installation

The switch platform uses 18U of rack space in a standard 19” rack, 16U for the chassis

and 2U for the shelf. The switch ships from the factory with mounting holes on the spine

side. There are upper brackets to connect the leaf side to the rack near the top of the chas-

sis, and there are two lock-down bars to secure the

chassis to the shelf. The weight of the

switch is supported from underneath the unit by the shelf.

This chassis can be installed in standard 19” racks tha

t have between 65cm and 80cm

between the vertical supports of the rack. Make sure that a fully populated rack including

cables will have sufficient air flow for cooling.

The rack mounting holes conform to the EIA-310 standard for 19-inch racks. Guaran-

tee proper ventilation, by leaving 8cm (3”) of space to the front and rear of the switch.

This will ensure proper air flow through the chassis. This is crucial for maintaining

good airflow at ambient temperature. In particular, route cables such that they do not

impede the air into or out of the chassis.

Insert the bottom spine board first.

Warning: This equipment is very heavy. Safety is the first concern. Make sure that

adequate manpower and proper equipment is used for transporting and moving the

chassis.

The fully loaded chassis weighs:

212.36 kg (468 LBS) full configuration

90 kg (199 LBS) empty configuration

112 kg (247 LBS) shipped configuration

Choose a rack which is able to support the mechanical and environmental characteris-

tics of a fully populated switch chassis.

InfiniBand FDR Switch Platform Hardware User Manual

Mellanox Technologies

18

1.7.1 Starting with the Rack

Rack Recommendation

1.7.1.1 Preparing the Rack

The rack may need to be modified to accommodate

the SX6518 chassis. The distance

between the vertical supports must be between 65 and 80cm.

Figure 1: Distance Between the Vertical Supports

1.7.2 ESD Connection

Before starting any procedure on the SX6518 switch system:

1. Put an ESD prevention wrist strap on your wrist, and

make sure there is good contact

between your body and the strap.

2. Plug the other end of the wrist strap to a valid

ground. Make sure that this is a tight

fit.

Due to the space required by up to 324 connector cables Mellanox recommends a rack

that is 100 cm long and 80cm wide. This will allow for proper cable management and

enough ventilation to properly cool the chassis.

This edge of the shelf must be as

close as possible to the inside of

the door when closed.

Vertical Supports

Between 65 and 80 cm.

InfiniBand FDR Switch Platform Hardware User Manual

Mellanox Technologies

19

1.7.3 Installation Procedure

1.7.3.1 Requirements

You will need:

1.7.3.2 Installation and Cable Management Kit Parts

• Parts included in the installation kit:

Installing the chassis will be a lot easier if you can remove the sides of the rack.

You will need a fork lift, to move and insert the chassis into the rack.

• #2 phillips screwdriver • #3 phillips screwdriver

• a fork lift • a grounding lug

• measuring tape • ground wire of sufficient length and gauge to properly ground the

cha

ssis

The installation will be much easier with a power screwdriver.

It is recommended to use AWG6 or 4mm diameter wire for grounding purposes.

It is recommended to have at least two people for the duration of the installation proce-

dure. Use a mechanical lift to raise this chassis. If not, use enough manpower to ensure

the safety and wellbeing of all of the people involved in the installation.

- 1 shelf with brackets pre-installed - 1 shelf extension

- 1 left side upper bracket offset - 1 right side upper bracket offset

- 2 lock down bars - 2 upper bracket washers

- 8 lock washers for the upper brackets to

vertical support

- 1 nut Size M-6 for ground post

- 10 hex head bolts – 8 for the upper

brackets and 2 for the shelf extension

- 26 caged nuts 12 for the shelf and 8 for the

chassis faceplate and 6 for the filler panels

- 26 pan head screws for the caged nuts 12

for the shelf and 8 for the chassis faceplate

and 6 for the filler panels

- 32 hex head bolts – 20 for the lock down

bars and 12 for the upper brackets to upper

bracket offsets

InfiniBand FDR Switch Platform Hardware User Manual

Mellanox Technologies

20

• Parts included in the cable management installation kit:

Figure 2: Installation Kit Parts

- 32 lock washers – 20 for the lock down

bars

and 12 for the upper brackets to

upper bracket offsets

- 12 flat head screws for the upper bracket

offsets

- 2 upper brackets - 1 socket nut driver 8mm

- 1 open end ratchet wrench 10mm - 1 socket nut driver 10mm

- 1 socket wrench - 1 socket nut driver 14mm

- 2 extensions for the socket driver - 1 box wrench

- 2 flat washers for the shelf extension - 6 two hole lock washers for lock down bars

- Bottom filler panel - Top filler panel

- 1 cable management rack RH - 1 cable management rack LH

- 14 caged nuts M6 - 14 M6 bolts

- 9 cable management shelves

Shelf

Caged nuts

Upper bracket

Lock washers

Phillips pan head

screw

Upper bracket offset

Shelf extension

Lock-down bar

Flat washers

hex head bolt

Upper bracket

washer

Flat head screw

Bottom filler panel

Top filler panel

Lock-down bar 2 hole

lock washer

Pagina se încarcă ...

Mellanox Technologies SX6518 Hardware Installation Manual

Acest manual este potrivit și pentru

Mellanox Technologies SX6518 Hardware Installation Manual

în alte limbi

Lucrări conexe

Alte documente