Makita DVC152L Manual de utilizare

DVC152L

DVC153L

DVC154L

EN Cordless Vacuum Cleaner INSTRUCTION MANUAL 8

PL Odkurzacz akumulatorowy INSTRUKCJA OBSŁUGI 19

HU Vezeték nélküli porszívó HASZNÁLATI KÉZIKÖNYV 33

SK Akumulátorový vysávač NÁVOD NA OBSLUHU 46

CS Bezdrátový akumulátorový

vysavač NÁVOD K OBSLUZE 58

UK Акумуляторний пилосос ІНСТРУКЦІЯ З

ЕКСПЛУАТАЦІЇ 70

RO Aspirator fără cablu MANUAL DE INSTRUCŢIUNI 83

DE Akku-Staubsauger BETRIEBSANLEITUNG 95

2

3

4

5

1

Fig.1

1

2

3

4

5

Fig.2

2

1

Fig.3

1

Fig.4

1

2

Fig.5

1

2

Fig.6

Fig.7

2

13

Fig.8

12

3

4

Fig.9

Fig.10

2

1

Fig.11

1

2

3

4

5

6

Fig.12

3

1

2

Fig.13

1

Fig.14

3

1

2

Fig.15

2

1

Fig.16

1

Fig.17

Fig.18

Fig.19

Fig.20

Fig.21

Fig.22

4

1

Fig.23

21

Fig.24

Fig.25

1

Fig.26

2

1

Fig.27

1

Fig.28

5

21

Fig.29

3

2

1

Fig.30

2

1

Fig.31

Fig.32

Fig.33

Fig.34

1

Fig.35

6

Fig.36

7

8ENGLISH

ENGLISH (Original instructions)

WARNING

This machine is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or a lack of

experience and knowledge.

Children should be supervised to ensure that they do not play with

the appliance.

SPECIFICATIONS

Model: DVC152L DVC153L DVC154L

Standard lter type Cloth lter

(for dry and wet dust)

Powder lter (for dry dust)

Maximum air volume (with BL1850B, ø38 mm x 2.5 m hose) 2.1 m3/min

Vacuum (with BL1850B, ø38 mm x 2.5 m hose) 9.8 kPa

Recoverable capacity Dust 15 L

Water 12 L -

Dimensions (L x W x H) 366 mm x 334 mm x 421 mm

Rated voltage D.C. 36 V

Net weight 7.3 - 7.9 kg 8.0 - 8.6 kg

Bluetooth® version -4.1

(Bluetooth low energy)

Frequency band -2,402 - 2,480 MHz

Maximum radio-frequency power -1.0 dBm (EIRP)

Transmission range -Approximately 10 m

• Due to our continuing program of research and development, the specications herein are subject to change

without notice.

• Specications and battery cartridge may differ from country to country.

• The weight does not include accessories but battery cartridge(s). The lightest and heaviest combination weight

of the appliance and battery cartridge(s) are shown in the table.

• For wet dust, the oat and the water lter or cloth lter are required.

The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of

such marks by Makita is under license. Other trademarks and trade names are those of their respective owners.

Applicable battery cartridge and charger

Battery cartridge BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 /

BL1840B / BL1850 / BL1850B / BL1860B

Charger DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF

• Some of the battery cartridges and chargers listed above may not be available depending on your region of

residence.

WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges

and chargers may cause injury and/or re.

9ENGLISH

Symbols

The followings show the symbols used for the equip-

ment. Be sure that you understand their meaning before

use.

Read instruction manual.

Take particular care and attention.

Warning! The cleaner may contain haz-

ardous dust.

Never stand on the cleaner.

Dust class L (light). The cleaners are capa-

ble of picking up dust class L. Follow your

country's regulations relating to dusts and

to occupational health and safety.

Ni-MH

Li-ion Only for EU countries

Do not dispose of electric equipment or

battery pack together with household

waste material! In observance of the

European Directives, on Waste Electric

and Electronic Equipment and Batteries

and Accumulators and Waste Batteries and

Accumulators and their implementation

in accordance with national laws, electric

equipment and batteries and battery

pack(s) that have reached the end of

their life must be collected separately and

returned to an environmentally compatible

recycling facility.

Intended use

The tool is suitable for commercial use, for example in

hotels, schools, hospitals, factories, shops, ofces and

rental businesses.

DVC152L

The tool is intended for collecting both wet and dry dust.

DVC153L, DVC154L

The tool is intended for collecting dry dust only.

Noise

The typical A-weighted noise level determined accord-

ing to EN60335-2-69:

Model DVC152L

Sound pressure level (LpA) : 70 dB(A) or less

Uncertainty (K) : 2.5 dB(A)

Model DVC153L

Sound pressure level (LpA) : 70 dB(A) or less

Uncertainty (K) : 2.5 dB(A)

Model DVC154L

Sound pressure level (LpA) : 70 dB(A) or less

Uncertainty (K) : 2.5 dB(A)

The noise level under working may exceed 80 dB (A).

NOTE: The declared noise emission value(s) has

been measured in accordance with a standard test

method and may be used for comparing one tool with

another.

NOTE: The declared noise emission value(s)

may also be used in a preliminary assessment of

exposure.

WARNING: Wear ear protection.

WARNING:

The noise emission during actual

use of the power tool can differ from the declared

value(s) depending on the ways in which the tool is

used especially what kind of workpiece is processed.

WARNING:

Be sure to identify safety measures

to protect the operator that are based on an estima-

tion of exposure in the actual conditions of use (tak-

ing account of all parts of the operating cycle such

as the times when the tool is switched off and when

it is running idle in addition to the trigger time).

Vibration

The vibration total value (tri-axial vector sum) deter-

mined according to EN60335-2-69:

Vibration emission (ah,M) : 2.5 m/s2 or less

Uncertainty (K) : 1.5 m/s2

NOTE: The declared vibration total value(s) has been

measured in accordance with a standard test method

and may be used for comparing one tool with another.

NOTE: The declared vibration total value(s) may also

be used in a preliminary assessment of exposure.

WARNING:

The vibration emission during actual

use of the power tool can differ from the declared val-

ue(s) depending on the ways in which the tool is used

especially what kind of workpiece is processed.

WARNING:

Be sure to identify safety measures

to protect the operator that are based on an estima-

tion of exposure in the actual conditions of use (tak-

ing account of all parts of the operating cycle such

as the times when the tool is switched off and when

it is running idle in addition to the trigger time).

EC Declaration of Conformity

For European countries only

The EC declaration of conformity is included as Annex A

to this instruction manual.

SAFETY WARNINGS

Cordless vacuum cleaner safety

warnings

WARNING: IMPORTANT! READ CAREFULLY

all safety warnings and all instructions BEFORE

USE. Failure to follow the warnings and instructions

may result in electric shock, re and/or serious injury.

1. Before use, make sure that this cleaner must

be used by people who have been adequately

instructed on the use of this cleaner.

2.

If foam/liquid comes out, switch off immediately.

3. Clean the water level limiting device regularly

and examine it for signs of damage.

4. Do not use the cleaner without the lter.

Replace a damaged lter immediately.

10 ENGLISH

5. AVOID UNINTENTIONAL STARTING. Be sure

switch is OFF when installing battery(ies).

6. Do not attempt to pick up ammable materials,

re works, lighted cigarettes, hot ashes, hot

metal chips, sharp materials such as razors,

needles, broken glass or the like.

7. NEVER USE THE CLEANER IN THE VICINITY

OF GASOLINE, GAS, PAINT, ADHESIVES OR

OTHER HIGHLY EXPLOSIVE SUBSTANCES.

The switch emits sparks when turned ON and

OFF. And so does the motor commutator during

operation. A dangerous explosion may result.

8.

Never vacuum up toxic, carcinogenic, com-

bustible or other hazardous materials such as

asbestos, arsenic, barium, beryllium, lead, pes-

ticides, or other health endangering materials.

9. Never use the cleaner outdoors in the rain.

10. Do not use close to heat sources (stoves, etc.).

11.

Do not block suction inlet/outlet/cooling vents.

These vents permit cooling of the motor.

Blockage should be carefully avoided otherwise

the motor will burn out from lack of ventilation.

12. Keep proper footing and balance at all times.

13. Do not fold, tug or step on the hose.

14. Stop the cleaner immediately if you notice

poor performance or anything abnormal

during operation.

15. REMOVE THE BATTERY(IES). When not in

use, before servicing, and when changing

accessories.

16.

Clean and service the cleaner immediately after

each use to keep it in tiptop operating condition.

17. MAINTAIN THE CLEANER WITH CARE. Keep

the cleaner clean for better and safer per-

formance. Follow instructions for changing

accessories. Keep handles dry, clean, and free

from oil and grease.

18. CHECK DAMAGED PARTS. Before further use

of the cleaner, a guard or other part that is

damaged should be carefully checked to deter-

mine that it will operate properly and perform

its intended function. Check for alignment of

moving parts, binding of moving parts, break-

age of parts, mounting, and any other condi-

tions that may affect its operation. A guard or

other part that is damaged should be properly

repaired or replaced by an authorized service

center unless otherwise indicated elsewhere

in this instruction manual. Have defective

switches replaced by authorized service cen-

ter. Don’t use the cleaner if switch does not

turn it on and off.

19. REPLACEMENT PARTS. When servicing, use

only identical replacement parts.

20. STORE IDLE CLEANER. When not in use, the

cleaner should be stored indoors.

21. Wet lters and the interior part of the liquid

container shall be dried before storage.

22. Be kind to your cleaner. Rough handling can

cause breakage of even the most sturdily built

cleaner.

23. Do not attempt to clean the exterior or interior

with benzine, thinner or cleaning chemicals.

Cracks and discoloration may be caused.

24. Do not use cleaner in an enclosed space where

ammable, explosive or toxic vapors are given

off by oil-base paint, paint-thinner, gasoline,

some mothproong substances, etc., or in

areas where ammable dust is present.

25. Do not operate the this or any tool while under

the inuence of drugs or alcohol.

26. As a basic rule of safety, use safety goggles or

safety glasses with side shields.

27. Use a dust mask in dusty work conditions.

28. This machine is not intended for use by per-

sons including children with reduced physical,

sensory or mental capabilities, or lack of expe-

rience and knowledge.

29. Young children should be supervised to

ensure that they do not play with the cleaner.

30. Never handle battery(ies) and cleaner with wet

hands.

31. Use extreme caution when cleaning on stairs.

32. Do not use the cleaner as a stool or work

bench. The machine may fall down and may

result in personal injury.

33. Before use, operators shall be provided with

information, instruction and training for the

use of the machine and the substances for

which it is to be used, including the safe

method of removal and disposal of the mate-

rial collected.

34. The machine should be technically inspected

by the manufacturer, or an instructed person,

at least annually, consisting of, for example,

inspection of lters for damage, air tightness

of the machine and proper function of the

control mechanism.

35. When carrying out service or repair opera-

tions, all contaminated items which cannot be

satisfactorily cleaned are to be disposed of;

such items shall be disposed of in impervious

bags in accordance with any current regula-

tion for the disposal of such waste.

Battery tool use and care

1. Recharge only with the charger specied by

the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of re

when used with another battery pack.

2. Use power tools only with specically desig-

nated battery packs. Use of any other battery

packs may create a risk of injury and re.

3. When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another. Shorting the battery termi-

nals together may cause burns or a re.

4. Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If con-

tact accidentally occurs, ush with water. If

liquid contacts eyes, additionally seek medical

help. Liquid ejected from the battery may cause

irritation or burns.

5. Do not use a battery pack or tool that is dam-

aged or modied. Damaged or modied batteries

may exhibit unpredictable behaviour resulting in

re, explosion or risk of injury.

11 ENGLISH

6. Do not expose a battery pack or tool to re or

excessive temperature. Exposure to re or tem-

perature above 130 °C may cause explosion.

7. Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range specied in the instruc-

tions. Charging improperly or at temperatures

outside the specied range may damage the

battery and increase the risk of re.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product. MISUSE or failure to follow the safety

rules stated in this instruction manual may cause

serious personal injury.

Important safety instructions for

battery cartridge

1.

Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using battery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4.

If electrolyte gets into your eyes, rinse them out

with clear water and seek medical attention right

away. It may result in loss of your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

ductive material.

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

A battery short can cause a large current

ow, overheating, possible burns and even a

breakdown.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a re.

8. Be careful not to drop or strike battery.

9. Do not use a damaged battery.

10. The contained lithium-ion batteries are subject

to the Dangerous Goods Legislation require-

ments.

For commercial transports e.g. by third parties,

forwarding agents, special requirement on pack-

aging and labeling must be observed.

For preparation of the item being shipped, consult-

ing an expert for hazardous material is required.

Please also observe possibly more detailed

national regulations.

Tape or mask off open contacts and pack up the

battery in such a manner that it cannot move

around in the packaging.

11. Follow your local regulations relating to dis-

posal of battery.

12. Use the batteries only with the products

specied by Makita. Installing the batteries to

non-compliant products may result in a re, exces-

sive heat, explosion, or leak of electrolyte.

SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that

have been altered, may result in the battery bursting

causing res, personal injury and damage. It will

also void the Makita warranty for the Makita tool and

charger.

Tips for maintaining maximum

battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice

less tool power.

2. Never recharge a fully charged battery car-

tridge. Overcharging shortens the battery

service life.

3. Charge the battery cartridge with room tem-

perature at 10 °C - 40 °C (50 °F - 104 °F). Let

a hot battery cartridge cool down before

charging it.

4. Charge the battery cartridge if you do not use

it for a long period (more than six months).

Important safety instructions for

wireless unit

1. Do not disassemble or tamper with the cleaner.

The wireless unit in the cleaner cannot be

removed.

2. Do not operate the wireless activation function

in places where medical instruments, heart

pace makers, or automated devices, such as

automatic doors and re alarms, are nearby.

3. Do not use the cleaner in places where the

temperature exceeds 50°C (122°F).

4. The wireless unit is an accurate instrument. Be

careful not to drop or strike the cleaner.

5. Do not leave the cleaner in a place where

static electricity or electrical noise could be

generated.

PARTS DESCRIPTION

Model DVC152L

(Cloth lter (for dry and wet dust) model)

► Fig.1: 1. Tank cover 2. Float 3. Float cage 4. Cloth

lter 5. Tank

Model DVC153L, DVC154L

(Powder lter (for dry dust) model)

► Fig.2: 1. Tank cover 2. Powder lter (HEPA)

3. Damper 4. Prelter 5. Tank

12 ENGLISH

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing or removing battery

cartridge

CAUTION: Always switch off the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the cleaner and the battery

cartridge rmly when installing or removing bat-

tery cartridge. Failure to hold the cleaner and the

battery cartridge rmly may cause them to slip off

your hands and result in damage to the cleaner and

battery cartridge and a personal injury.

CAUTION: Be careful not to pinch your n-

gers when opening or closing the battery cover.

Failure to do so may cause personal injury.

To install the battery cartridge, release the lock rst, and

then open the battery cover. After that, insert the battery

cartridge.

► Fig.3: 1. Lock 2. Battery cover

Align the tongue on the battery cartridge with the groove

in the housing and slip it into place. Insert it all the way

until it locks in place with a little click. Then lock the

battery cover.

► Fig.4: 1. Battery cartridge

To remove the battery cartridge, slide it from the tool

while sliding the button in front of the cartridge.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,

it may accidentally fall out of the cleaner, causing

injury to you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

not being inserted correctly.

NOTE: The cleaner does not work with only one

battery cartridge.

Indicating the remaining battery

capacity

Only for battery cartridges with the indicator

► Fig.5: 1. Indicator lamps 2. Check button

Press the check button on the battery cartridge to indi-

cate the remaining battery capacity. The indicator lamps

light up for a few seconds.

Indicator lamps Remaining

capacity

Lighted Off Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

The battery

may have

malfunctioned.

NOTE: Depending on the conditions of use and the

ambient temperature, the indication may differ slightly

from the actual capacity.

Indicating the remaining battery

capacity

► Fig.6: 1. Battery indicator 2. Check button

► Fig.7

Press the check button to indicate the remaining battery

capacities. The battery indicators correspond to each

battery.

Battery indicator status Remaining

battery

capacity

On Off Blinking

50% to 100%

20% to 50%

0% to 20%

Charge the

battery

NOTE: During the cleaner turned on with the stand-by

switch set to "AUTO", the battery indicator does not

work.

Tool / battery protection system

The tool is equipped with a tool/battery protection sys-

tem. This system automatically cuts off power to the

motor to extend tool and battery life. The tool will auto-

matically stop during operation if the tool or battery is

placed under one of the following conditions:

13 ENGLISH

Overload protection

When the tool is operated in a manner that causes it to

draw an abnormally high current, the tool automatically

stops without any indication. In this situation, turn the

tool off and stop the application that caused the tool to

become overloaded. Then turn the tool on to restart.

Overheat protection

On Blinking

When the tool is overheated, the tool stops automatically, and

the battery indicator blinks about 60 seconds. In this situa-

tion, let the tool cool down before turning the tool on again.

Overdischarge protection

When the battery capacity becomes low, the tool stops

automatically. If the product does not operate even

when the switches are operated, remove the batteries

from the tool and charge the batteries.

Switch action

► Fig.8: 1. Stand-by switch 2. Power button 3. Suction

force adjusting knob

To start the cleaner:

1. Set the stand-by switch to the "I" side. The cleaner

gets into stand-by state.

2. Press the power button.

To make the cleaner get into stand-by mode, press the

power button again.

To turn off the cleaner, set the stand-by switch to the "O" side.

The suction power can be adjusted according to your work need.

Suction power can be increased by turning the suction force

adjusting knob from the symbol to the symbol.

NOTICE: Always set the stand-by switch to the "O"

side when not using the cleaner for long time. The

cleaner consumes power during stand-by state.

Auto-suction stop during wet

suction operation

Only for the cloth lter model

WARNING: Do not use for a long time while

the oat is at work. Using the cleaner with its oat at

work for a long time can cause overheat, resulting in

the cleaner deformation.

WARNING: Do not pick up foam or soapy

liquid. Picking up foam or soapy liquid can cause

foam to come out of air exit before the oat works.

Continuing to using in this condition may cause an

electric shock and breakage of the cleaner.

Auto-suction stop works only when using with the oat

and oat cage.

The cleaner has a oat mechanism that prevents water

from immersing into the motor when picking up more

than a certain amount of water. When the tank is full

and the cleaner no longer picks up water, switch off the

cleaner and empty the tank.

Locking or unlocking the caster

► Fig.9: 1. Caster 2. Stopper lever 3. FREE position

4. LOCK position

Locking the caster is convenient when storing the

cleaner, stopping the work on the way and keeping the

cleaner still.

To operate the stopper, move it by hand.

To lock the caster with a stopper, lower the stopper

lever and the caster no longer will rotate. To release the

caster from the locked position, raise the stopper lever.

NOTE: When moving the cleaner, make sure that

the caster is unlocked. Moving the cleaner with the

caster in the locked position may cause damage to

the caster.

Carriage handle

When carrying the cleaner, carry it by holding the han-

dle on the head. The handle is retractable at the head

when not in use.

► Fig.10

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

CAUTION: Always wear dust mask during

assembly or maintenance.

Installing the powder lter (HEPA)

and prelter (for dry dust)

Optional accessory for cloth lter model

CAUTION: Never pick up water or other liq-

uids or wet dusts when using the powder lter.

Picking up such things may cause the powder lter

breakage.

To use powder lter:

1. Remove the oat cage and oat by removing the

bolts.

► Fig.11: 1. Float 2. Float cage

2. Place the prelter in the tank with aligning the

mounting position markings.

3. Mount the damper on the powder lter and then

place them in the prelter with aligning the mounting

position markings.

4. Finally, mount the tank cover and lock it.

► Fig.12: 1. Tank cover 2. Powder lter (HEPA)

3. Damper 4. Prelter 5. Tank 6. Mounting

position marking

NOTICE: Before using the powder lter, make

sure that prelter and damper are always used

together. It is not allowed to install powder lter

solely.

14 ENGLISH

Installing the water lter

Optional accessory for cloth lter model

CAUTION: Never pick up water or wet dust

without the oat and the cloth lter or the water

lter.

CAUTION: For picking up wet dust, make

sure that the oat cage and the oat are installed

on the cleaner.

CAUTION: When installing the water lter on

the tank, set it tight at the opening of the tank so

that the hook of the water lter engages the tank

opening rmly and there is no space between the

water lter and the tank.

To pick up water or wet dust only, the water lter is more

suitable than the cloth lter.

When installing the water lter, align its mounting posi-

tion mark with the one on the tank.

► Fig.13: 1. Water lter 2. Tank 3. Mounting position

marking

NOTE: It is recommended using water lter when

picking up large amount of water repeatedly.

Otherwise vacuum ability may be reduced in case of

cloth lter.

Installing the paper pack

Optional accessory

WARNING: When using the paper pack, also

use the cloth lter or prelter together that is

preinstalled on the cleaner. Failure to use the cloth

lter / prelter together may cause unusual noise and

heat, resulting in a re.

CAUTION: (For the cloth lter model)

• Never pick up water or other liquids or wet

dusts when using the paper pack. Picking

up such things may cause the paper pack

breakage.

• Before using the paper pack, make sure that

powder lter (optional accessory), damper

(optional accessory) and prelter are always

used together.

CAUTION: (For the powder lter model)

• Before using the paper pack, make sure

that powder lter, damper and prelter are

always used together.

1. Remove the rubber holder.

► Fig.14: 1. Rubber holder

2. Extend the paper pack.

3. Align the paper pack opening with the dust suction

opening of the cleaner.

4. Insert the cardboard of the paper pack onto the

holder so that it is positioned at the end beyond the

detent protrusion.

► Fig.15: 1. Paper pack 2. Holder

Installing the polyethylene bag

Cleaner can also be used without polyethylene bag.

However, using polyethylene bag is easier to empty the

tank without letting your hands dirty.

Spread the polyethylene bag in the tank. Insert it between

the holder plate and the tank, and pull it to the hose inlet.

► Fig.16: 1. Holder plate 2. Polyethylene bag

Spread the bag around the top of the tank so that the cloth

lter / prelter edge can catch and hold the bag securely.

► Fig.17: 1. Cloth lter / prelter

NOTE: A polyethylene bag available on the

market can be used. 0.04 mm or thicker one is

recommended.

NOTE: Too much dust will tear the bag easily, so

do not collect the dust more than the half of the bag

capacity.

Emptying the polyethylene bag

WARNING: Always make sure that the

cleaner is switched off and the battery cartridge is

removed before emptying the polyethylene bag.

Failure to do so may cause an electric shock and

serious personal injury.

CAUTION: Do not apply a great impact on the

oat cage and tank. Applying a great impact may

cause deformation and damage to the parts.

CAUTION: Empty the tank at least once a day

although this depends on picked-up dust volume

in the tank. Or, the suction force will weaken and the

motor may be broken.

CAUTION: Do not grab the hook when empty-

ing the tank. Grabbing the hook may cause the hook

to break.

Unhook and lift up the tank cover.

Shake off the dust from the cloth lter / prelter and then

take the polyethylene bag out of the tank.

► Fig.18

NOTE: Take the polyethylene bag carefully out of the

tank so that the polyethylene bag cannot be caught

and torn by the protrusion inside the tank when emp-

tying it.

NOTE: Empty the polyethylene bag before it

becomes full. Too much dust in the tank may cause

the polyethylene bag to be torn.

Installing the tool box

1. Release the lock of the battery cover, and open

the battery cover.

2. Set the rails on the tool box along the grooves on

the housing.

3. Close the battery cover and apply the lock.

► Fig.19

The tool box is convenient for carrying batteries, pipe,

or cuffs.

► Fig.20

15 ENGLISH

Connecting the hose

NOTICE:

Never force the hose for bending or stamp it.

Never move the cleaner by a hose. Forcing, stamping and pull-

ing the hose may cause a breakage or deformation of the hose.

NOTICE:

When picking up large wastes such as

planer carvings, concrete dusts or similar other than

small wastes, use the 38 mm inner diameter hose

(optional accessory). Using the 28 mm inner diameter hose

(optional accessory) may cause a hose stufng and damage.

Insert the hose onto the mounting port of the tank and

turn it clockwise until it locks.

► Fig.21

WIRELESS ACTIVATION

FUNCTION

For DVC154L only

What you can do with the wireless

activation function

The wireless activation function enables clean and

comfortable operation. By connecting a supported tool

to the cleaner, you can run the cleaner automatically

along with the switch operation of the tool.

► Fig.22

NOTICE:

Be sure to refer to the instruction manual of the

tool when using the cleaner with wireless activation function.

NOTICE: Do not disassemble or tamper with the

wireless unit.

NOTICE: Always close the lid of the wireless unit

in the tool when operating or storage.

NOTICE:

Do not remove the wireless unit from the

tool while the power is being supplied to the tool.

Doing so may cause a malfunction of the wireless unit.

NOTICE:

Do not press the wireless activation button too

hard and/or press the button with an object with a sharp edge.

NOTE: Wireless activation needs Makita tools

equipped with the wireless unit.

NOTE:

Prior to the initial use of the wireless activation

function with each tool, the tool registration is required.

Once the registration is nished with the tool, the

re-registration is not required unless it is cancelled.

NOTE: Before registration, be sure that the wireless

unit is properly inserted into the tool.

NOTE: One cleaner can register up to 10 tools. If

more than 10 tools are registered to the cleaner, the

tool registered earliest will be cancelled automatically.

NOTE: The position of the wireless activation button

varies depending on the tool.

NOTE: The cleaner also starts by pressing the power

button when the stand-by switch is set to "AUTO".

However the power button will not actuate when the

wireless activation function is used.

Tool registration for the cleaner

NOTE: A Makita tool supporting the wireless activa-

tion function is required for the tool registration.

NOTE: Finish installing the wireless unit to the tool

before starting the tool registration.

NOTE: During the tool registration, do not pull the

switch trigger on the tool or turn on the power switch

on the cleaner.

NOTE: Refer to the instruction manual of the tool, too.

If you wish to activate the cleaner along with the

switch operation of the tool, nish the tool registration

beforehand.

1. Install the batteries to the cleaner and the tool.

2. Set the stand-by switch on the cleaner to "AUTO".

► Fig.23: 1. Stand-by switch

3. Press the wireless activation button on the cleaner

for 3 seconds until the wireless activation lamp blinks in

green. And then press the wireless activation button on

the tool in the same way.

► Fig.24: 1. Wireless activation button 2. Wireless

activation lamp

If the cleaner and the tool are linked successfully, the

wireless activation lamps will light up in green for 2

seconds and start blinking in blue.

NOTE: The wireless activation lamps nish blinking

in green after 20 seconds elapsed. Press the wireless

activation button on the tool while the wireless acti-

vation lamp on the cleaner is blinking. If the wireless

activation lamp does not blink in green, push the wire-

less activation button briey and hold it down again.

NOTE: When performing two or more tool registration

for the cleaner, nish the tool registration one by one.

Starting the wireless activation function

NOTE: Finish the tool registration for the cleaner for

wireless activation.

NOTE: Always place the cleaner so that you can see

the status of the wireless activation lamp.

NOTE: Refer to the instruction manual of the tool, too.

After registering a tool to the cleaner, the cleaner will auto-

matically runs along with the switch operation of the tool.

1. Install the wireless unit to the tool.

2. Connect the hose of the cleaner with the tool.

► Fig.25

3. Set the stand-by switch on the cleaner to "AUTO".

► Fig.26: 1. Stand-by switch

4. Push the wireless activation button on the tool

briey. The wireless activation lamp will blink in blue.

► Fig.27: 1. Wireless activation button 2. Wireless

activation lamp

5.

Pull the switch trigger of the tool. Check if the cleaner

runs while the switch trigger on the tool is being pulled.

To stop the wireless activation, push the wireless activa-

tion button on the tool, or set the stand-by switch on the

cleaner to "I" or "O".

16 ENGLISH

NOTE:

The wireless activation lamp on the tool will stop

blinking in blue when there is no operation for 2 hours. In

this case, set the stand-by switch on the cleaner to "AUTO"

and press the wireless activation button on the tool again.

NOTE:

The cleaner starts/stops with a delay. There is a time

lag when the cleaner detects a switch operation of the tool.

NOTE:

The transmission distance of the wireless unit may

vary depending on the location and surrounding circumstances.

NOTE: When two or more tools are registered to one

cleaner, the cleaner may start running even if you

don't pull the switch trigger because other user is

using the wireless activation function.

Cancelling tool registration for the cleaner

Perform the following procedure when cancelling the

tool registration for the cleaner.

1. Install the batteries to the cleaner and the tool.

2. Set the stand-by switch on the cleaner to "AUTO".

► Fig.28: 1. Stand-by switch

3. Press the wireless activation button on the cleaner

for 6 seconds. The wireless activation lamp blinks in

green and then become red. After that, press the wire-

less activation button on the tool in the same way.

► Fig.29: 1. Wireless activation button 2. Wireless

activation lamp

If the cancellation is performed successfully, the wireless activation

lamps will light up in red for 2 seconds and start blinking in blue.

NOTE: The wireless activation lamps nish blinking in

red after 20 seconds elapsed. Press the wireless acti-

vation button on the tool while the wireless activation

lamp on the cleaner is blinking. If the wireless acti-

vation lamp does not blink in red, push the wireless

activation button briey and hold it down again.

Erasing all tool registrations

You can erase all tool registrations from the cleaner as follows.

► Fig.30: 1. Stand-by switch 2. Wireless activation

button 3. Wireless activation lamp

1. Install the batteries to the cleaner.

2. Set the stand-by switch to "AUTO".

3. Hold down the wireless activation button for about

6 seconds until the wireless activation lamp blinks in red

(about twice per one second).

4. When the wireless activation lamp starts blinking

in red, release your nger from the wireless activation

button. Thereafter, hold down the wireless activation

button again for about 6 seconds.

5. When the wireless activation lamp starts blinking

fast (about 5 times per one second) in red, release your

nger from the wireless activation button. When the

wireless activation lamp lights up in red and later lights

off, all tool registrations are erased.

NOTE:

If the wireless activation lamp does not blink in red,

press the wireless activation button briey and try again.

Description of the wireless activation lamp status

► Fig.31: 1. Wireless activation button 2. Wireless

activation lamp

The wireless activation lamp shows the status of the wireless activation function. Refer to the below table for the

meaning of the lamp status.

Status Wireless activation lamp Description

Color

On

Blinking

Duration

Standby Blue Cleaner: con-

tinuing

Tool: 2 hours

Waiting for the tool registration or the wireless activation function

is available.

The lamp on the cleaner blinks when the stand-by switch is set in

AUTO. The lamp on the tool blinks when the wireless activation

button is pushed. The lamp on the tool will automatically turn off

when no operation is performed for 2 hours.

When the tool is

running. The wireless activation of the cleaner is available and the tool is

running.

Tool

registration Green 20 seconds Ready for the tool registration. Searching the tool to be registered.

2 seconds The tool registration has been nished. The wireless activation

lamp will start blinking in blue.

Cancelling/

erasing

tool

registration

Red

(slow: 2 times/sec.) 20 seconds Ready for the cancellation of the tool registration. Searching the

tool to be cancelled.

(fast: 5 times/sec.) When the

wireless acti-

vation button is

pressed down.

Ready to erase all tool registrations.

2 seconds The tool registration has been cancelled/erased. The wireless

activation lamp will start blinking in blue.

Others Red 3 seconds The power is supplied to the wireless unit and the wireless activa-

tion function is starting up.

Off - - The stand-by switch is not set to "AUTO".

17 ENGLISH

Troubleshooting for wireless activation function

Before asking for repairs, conduct your own inspection rst. If you nd a problem that is not explained in the manual,

do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replace-

ment parts for repairs.

State of abnormality Probable cause (malfunction) Remedy

The wireless activation lamp does

not light/blink.

The wireless unit is not installed into the tool.

The wireless unit is improperly installed

into the tool.

Install the wireless unit correctly in the tool.

The terminal of the wireless unit and/or

the slot is dirty. Gently wipe off dust and dirt on the terminal of the

wireless unit and clean the slot of the tool.

The wireless activation button on the

tool has not been pushed. Push the wireless activation button on the tool

briey.

The stand-by switch on the cleaner is

not set to "AUTO". Set the stand-by switch on the cleaner to "AUTO".

No power supply Supply the power to the tool and the cleaner.

Cannot nish tool registration / can-

celling tool registration successfully.

The wireless unit is not installed into the tool.

The wireless unit is improperly installed

into the tool.

Install the wireless unit correctly in the tool.

The terminal of the wireless unit and/or

the slot is dirty. Gently wipe off dust and dirt on the terminal of the

wireless unit and clean the slot of the tool.

The stand-by switch on the cleaner is

not set to "AUTO". Set the stand-by switch on the cleaner to "AUTO".

No power supply Supply the power to the tool and the cleaner.

Incorrect operation Push the wireless activation button briey and

perform the tool registration/cancellation procedures

again.

The tool and cleaner is away from each

other (out of the transmission range). Get the tool and the cleaner closer to each other.

The maximum transmission distance is approxi-

mately 10 m however it may vary according to the

circumstances.

Before nishing the tool registration/

cancellation;

- the switch trigger on the tool is pulled or;

- the power button on the cleaner is turned on.

Push the wireless activation button briey and

perform the tool registration/cancellation procedures

again.

The tool registration procedures for the

tool or the cleaner has not nished. Perform the tool registration procedures for the tool

and the cleaner at the same timing.

Radio disturbance by other appliances

which generate high-intensity radio waves.

Keep the tool and the cleaner away from the appli-

ances such as Wi-Fi devices and microwave ovens.

The cleaner does not run along with

the switch operation of the tool.

The wireless unit is not installed into the tool.

The wireless unit is improperly installed

into the tool.

Install the wireless unit correctly in the tool.

The terminal of the wireless unit and/or

the slot is dirty. Gently wipe off dust and dirt on the terminal of the

wireless unit and clean the slot of the tool.

The wireless activation button on the

tool has not been pushed.

Push the wireless activation button briey and make

sure that the wireless activation lamp is blinking in blue.

The stand-by switch on the cleaner is

not set to "AUTO". Set the stand-by switch on the cleaner to "AUTO".

More than 10 tools are registered to

the cleaner. Perform the tool registration again.

If more than 10 tools are registered to the cleaner,

the tool registered earliest will be cancelled

automatically.

The cleaner erased all tool

registrations. Perform the tool registration again.

No power supply Supply the power to the tool and the cleaner.

The tool and cleaner is away from each

other (out of the transmission range).

Get the tool and the cleaner closer to each other. The

maximum transmission distance is approximately 10 m

however it may vary according to the circumstances.

Radio disturbance by other appliances

which generate high-intensity radio waves.

Keep the tool and the cleaner away from the appli-

ances such as Wi-Fi devices and microwave ovens.

The cleaner runs while the tool's

switch trigger is not pulled. Other users are using the wireless acti-

vation of the cleaner with their tools. Turn off the wireless activation button of the other

tools or cancel the tool registration of the other

tools.

18 ENGLISH

State of abnormality Probable cause (malfunction) Remedy

Cannot erase all tool registrations in

the cleaner. Pressing the wireless button on the tool. Press the wireless button on the cleaner for erasing

all tool registrations.

The stand-by switch on the cleaner is

not set to "AUTO". Set the stand-by switch on the cleaner to "AUTO".

The wireless activation button is not

held down correctly. Hold down the wireless activation button for more

than 6 seconds and then release it when the wire-

less activation lamp blinks in red. Hold down the

wireless activation button for more than 6 seconds

again until the wireless activation button rapidly

blinks in red and then release the button.

MAINTENANCE

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before attempting to perform inspection or

maintenance.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

To maintain product SAFETY and RELIABILITY,

repairs, any other maintenance or adjustment should

be performed by Makita Authorized or Factory Service

Centers, always using Makita replacement parts.

Storage of accessories

The pipes can be placed into the pipe holder when not

using the cleaner for a short time.

► Fig.32

► Fig.33

The hose can be stored around the tool by connecting

each ends.

► Fig.34

Cleaning of cloth lter

Only for the cloth lter model

Clogged cloth lter causes poor suction performance.

Clean out the cloth lter from time to time.

To remove dust or particles adhering to the cloth lter,

shake the frame bottom quickly several times.

► Fig.35: 1. Cloth lter

Cleaning of powder lter (HEPA) and

prelter

Only for the powder lter model

Clogged powder lter, prelter and damper cause poor

suction performance. Clean out the lters and dampers

from time to time.

To remove dust or particles adhering to the lters, shake

the frame bottom quickly several times.

► Fig.36

Occasionally wash the powder lter in water, rinse and

dry thoroughly in the shade before use. Never wash

lters in a washing machine.

NOTE: Do not rub or scratch the powder lter, the

prelter or the damper with hard objects such as a

brush and a paddle.

NOTE: The lters wear out in course of time. It is

recommended to have some spares for them.

OPTIONAL

ACCESSORIES

CAUTION: These accessories or attachments

are recommended for use with your Makita tool

specied in this manual. The use of any other

accessories or attachments might present a risk of

injury to persons. Only use accessory or attachment

for its stated purpose.

If you need any assistance for more details regard-

ing these accessories, ask your local Makita Service

Center.

• Hose

• Front cuff (22, 24, 38)

• Straight pipe

• Corner nozzle

• Round brush

• Powder lter, HEPA (for dry dust)

• Damper

• Prelter

• Nozzle assembly

• Bent pipe

• Polyethylene bag

• Paper pack

• Holder set

• Water Filter (option for the cloth lter model)

• Makita genuine battery and charger

NOTE: Some items in the list may be included in the

tool package as standard accessories. They may

differ from country to country.

19 POLSKI

POLSKI (Instrukcja oryginalna)

OSTRZEŻENIE

To urządzenie nie jest przeznaczone do użytkowania przez osoby

(w tym dzieci) o ograniczonej sprawności ruchowej, sensorycznej

lub umysłowej oraz osoby nieposiadające odpowiedniej wiedzy i

doświadczenia.

Należy pilnować, aby dzieci nie bawiły się urządzeniem.

DANE TECHNICZNE

Model: DVC152L DVC153L DVC154L

Filtr standardowy Filtr z tkaniny

(do pyłu suchego i

mokrego)

Filtr pyłu (do pyłu suchego)

Maks. przepływ powietrza (BL1850B, wąż ø38 mm x 2,5 m) 2,1 m3/min

Podciśnienie (BL1850B, wąż ø38 mm x 2,5 m) 9,8 kPa

Pojemność Pył 15 l

Woda 12 l –

Wymiary (dług. x szer. x wys.) 366 mm x 334 mm x 421 mm

Napięcie znamionowe Prąd stały 36 V

Ciężar netto 7,3–7,9 kg 8,0–8,6 kg

Wersja Bluetooth®–4.1

(Bluetooth low energy)

Pasmo częstotliwości –2 402–2 480 MHz

Maksymalna moc częstotliwości radiowej –1,0 dBm (EIRP)

Zasięg przesyłania danych –Około 10 m

• W związku ze stale prowadzonym przez naszą rmę programem badawczo-rozwojowym niniejsze dane mogą

ulec zmianom bez wcześniejszego powiadomienia.

• W innych krajach urządzenie może mieć odmienne parametry techniczne i może być wyposażone w inny

akumulator.

• Waga nie uwzględnia akcesoriów (oprócz akumulatorów). Wagę najlżejszych i najcięższych kombinacji urzą-

dzenia z akumulatorami przedstawiono w tabeli.

• W przypadku mokrego pyłu wymagane jest stosowanie pływaka oraz ltra wody lub ltra z tkaniny.

Znak słowny i logo Bluetooth® to znaki towarowe będące własnością Bluetooth SIG, Inc., których rma Makita używa

na warunkach licencji. Pozostałe znaki i nazwy handlowe należą do ich odpowiednich właścicieli.

Kompatybilne akumulatory i ładowarki

Akumulator BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 /

BL1840B / BL1850 / BL1850B / BL1860B

Ładowarka DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF

• Pewne z wymienionych powyżej akumulatorów i ładowarek mogą być niedostępne w regionie zamieszkania

użytkownika.

OSTRZEŻENIE: Należy używać wyłącznie akumulatorów i ładowarek wymienionych powyżej.

Używanie innych akumulatorów i ładowarek może stwarzać ryzyko wystąpienia obrażeń ciała lub pożaru.

20 POLSKI

Symbole

Poniżej pokazano symbole zastosowane na urządze-

niu. Przed rozpoczęciem użytkowania należy zapoznać

się z ich znaczeniem.

Przeczytać instrukcję obsługi.

Zachować szczególną ostrożność.

Ostrzeżenie! W odkurzaczu może się

znajdować niebezpieczny pył.

Nigdy nie stawać na odkurzaczu.

Klasa pyłu L (lekki). Odkurzacze przezna-

czone są do zbierania pyłu klasy L. Należy

postępować zgodnie z przepisami lokal-

nymi odnoszącymi się do pyłów oraz do

bezpieczeństwa i higieny pracy.

Ni-MH

Li-ion Dotyczy tylko państw UE

Nie wyrzucać urządzeń elektrycznych ani

akumulatorów wraz z odpadami z gospo-

darstwa domowego! Zgodnie z dyrekty-

wami europejskimi w sprawie zużytego

sprzętu elektrycznego i elektronicznego

oraz baterii i akumulatorów oraz zużytych

baterii i akumulatorów, a także dostoso-

waniem ich do prawa krajowego, zużyte

urządzenia elektryczne, baterie i akumu-

latory należy składować osobno i przeka-

zywać do zakładu recyklingu działającego

zgodnie z przepisami dotyczącymi ochrony

środowiska.

Przeznaczenie

Narzędzie jest przeznaczone do użytku komercyjnego,

na przykład w hotelach, szkołach, szpitalach, fabrykach,

sklepach, biurach oraz przez rmy świadczące usługi

wynajmu narzędzi.

DVC152L

Narzędzie przeznaczone jest do odsysania suchego i

mokrego pyłu.

DVC153L, DVC154L

To narzędzie jest przeznaczone do odsysania tylko

suchego pyłu.

Hałas

Typowy równoważny poziom dźwięku A określony w

oparciu o normę EN60335-2-69:

Model DVC152L

Poziom ciśnienia akustycznego (LpA): 70 dB(A) lub mniej

Niepewność (K): 2,5 dB(A)

Model DVC153L

Poziom ciśnienia akustycznego (LpA): 70 dB(A) lub mniej

Niepewność (K): 2,5 dB(A)

Model DVC154L

Poziom ciśnienia akustycznego (LpA): 70 dB(A) lub mniej

Niepewność (K): 2,5dB(A)

Poziom hałasu podczas pracy może przekraczać 80 dB (A).

WSKAZÓWKA: Deklarowana wartość emisji hałasu

została zmierzona zgodnie ze standardową metodą

testową i można ją wykorzystać do porównywania

narzędzi.

WSKAZÓWKA: Deklarowaną wartość emisji hałasu

można także wykorzystać we wstępnej ocenie

narażenia.

OSTRZEŻENIE: Nosić ochronniki słuchu.

OSTRZEŻENIE: Poziom hałasu wytwa-

rzanego podczas rzeczywistego użytkowania

elektronarzędzia może się różnić od wartości

deklarowanej w zależności od sposobu użytko-

wania narzędzia, a w szczególności od rodzaju

obrabianego elementu.

OSTRZEŻENIE: W oparciu o szacowane

narażenie w rzeczywistych warunkach użytkowa-

nia należy określić środki bezpieczeństwa w celu

zapewnienia ochrony operatora (uwzględniając

wszystkie elementy cyklu działania, tj. czas, kiedy

narzędzie jest wyłączone i kiedy pracuje na biegu

jałowym, a także czas, kiedy jest włączone).

Drgania

Całkowita wartość poziomu drgań (suma wektorów w 3

osiach) określona zgodnie z normą EN60335-2-69:

Emisja drgań (ah,M): 2,5 m/s2 lub mniej

Niepewność (K): 1,5 m/s2

WSKAZÓWKA: Deklarowana wartość poziomu

drgań została zmierzona zgodnie ze standardową

metodą testową i można ją wykorzystać do porówny-

wania narzędzi.

WSKAZÓWKA: Deklarowaną wartość poziomu

drgań można także wykorzystać we wstępnej ocenie

narażenia.

OSTRZEŻENIE: Drgania wytwarzane pod-

czas rzeczywistego użytkowania elektronarzędzia

mogą się różnić od wartości deklarowanej w

zależności od sposobu użytkowania narzędzia,

a w szczególności od rodzaju obrabianego

elementu.

OSTRZEŻENIE: W oparciu o szacowane

narażenie w rzeczywistych warunkach użytkowa-

nia należy określić środki bezpieczeństwa w celu

zapewnienia ochrony operatora (uwzględniając

wszystkie elementy cyklu działania, tj. czas, kiedy

narzędzie jest wyłączone i kiedy pracuje na biegu

jałowym, a także czas, kiedy jest włączone).

Deklaracja zgodności WE

Dotyczy tylko krajów europejskich

Deklaracja zgodności WE jest dołączona jako załącznik

A do niniejszej instrukcji obsługi.

Pagina se încarcă ...

Makita DVC152L Manual de utilizare

Makita DVC152L Manual de utilizare

în alte limbi

Lucrări conexe

Alte documente