Daikin 3MXM40N Manualul proprietarului

Marca: Daikin

Model: 3MXM40N

Categorie: Aparate de aer condiționat cu sistem divizat

Tip: Manualul proprietarului

INSTALLATION

MANUAL

R32 Split Series

Models

3MXM40M2V1B

3MXM52M2V1B

3AMXM52M2V1B

3MXM68M2V1B

4MXM68M2V1B

4MXM80M2V1B

5MXM90M2V1B

Deutsch

Français

Nederlands

Español

Italiano

Ελληνικά

Portugues

Русский

Türkçe

Downloaded from www.Manualslib.com manuals search engine

Daikin Industries Czech Republic s.r.o.

CE - DECLARATION-OF-CONFORMITY

CE - KONFORMITÄTSERKLÄRUNG

CE - DECLARATION-DE-CONFORMITE

CE - CONFORMITEITSVERKLARING

CE - DECLARACION-DE-CONFORMIDAD

CE - DICHIARAZIONE-DI-CONFORMITA

CE - ΔHΛΩΣΗ ΣΥΜΜΟΡΦΩΣΗΣ

CE - DECLARAÇÃO-DE-CONFORMIDADE

CE - ЗАЯВЛЕНИЕ-О-СООТВЕТСТВИИ

CE - OVERENSSTEMMELSESERKLÆRING

CE - FÖRSÄKRAN-OM-ÖVERENSTÄMMELSE

CE - ERKLÆRING OM-SAMSVAR

CE - ILMOITUS-YHDENMUKAISUUDESTA

CE - PROHLÁŠENÍ-O-SHODĚ

CE - IZJAVA-O-USKLAĐENOSTI

CE - MEGFELELŐSÉGI-NYILATKOZAT

CE - DEKLARACJA-ZGODNOŚCI

CE - DECLARAŢIE-DE-CONFORMITATE

CE - IZJAVA O SKLADNOSTI

CE - VASTAVUSDEKLARATSIOON

CE - ДЕКЛАРАЦИЯ-ЗА-ϹЪОТВЕТСТВИЕ

CE - ATITIKTIES-DEKLARACIJA

CE - ATBILSTĪBAS-DEKLARĀCIJA

CE - VYHLÁSENIE-ZHODY

CE - UYGUNLUK-BEYANI

are in conformity with the following standard(s) or other

normative document(s), provided that these are used in

accordance with our instructions:

der/den folgenden Norm(en) oder einem anderen

Normdokument oder -dokumenten entspricht/entsprechen, unter

der Voraussetzung, daß sie gemäß unseren Anweisungen

eingesetzt werden:

sont conformes à la/aux norme(s) ou autre(s) document(s)

normatif(s), pour autant qu'ils soient utilisés conformément à nos

instructions:

conform de volgende norm(en) of één of meer andere bindende

documenten zijn, op voorwaarde dat ze worden gebruikt

overeenkomstig onze instructies:

están en conformidad con la(s) siguiente(s) norma(s) u otro(s)

documento(s) normativo(s), siempre que sean utilizados de

acuerdo con nuestras instrucciones:

sono conformi al(i) seguente(i) standard(s) o altro(i)

documento(i) a carattere normativo, a patto che vengano usati in

conformità alle nostre istruzioni:

είναι σύμφωνα με το(α) ακόλουθο(α) πρότυπο(α) ή άλλο

έγγραφο(α) κανονισμών, υπό την προϋπόθεση ότι

χρησιμοποιούνται σύμφωνα με τις οδηγίες μας:

estão em conformidade com a(s) seguinte(s) norma(s) ou

outro(s) documento(s) normativo(s), desde que estes sejam

utilizados de acordo com as nossas instruções:

соответствуют следующим стандартам или другим

нормативным документам, при условии их использования

согласно нашим инструкциям:

overholder følgende standard(er) eller andet/andre

retningsgivende dokument(er), forudsat at disse anvendes i

henhold til vore instrukser:

respektive utrustning är utförd i överensstämmelse med och

följer följande standard(er) eller andra normgivande dokument,

under förutsättning att användning sker i överensstämmelse med

våra instruktioner:

respektive utstyr er i overensstemmelse med følgende

standard(er) eller andre normgivende dokument(er), under

forutssetning av at disse brukes i henhold til våre instrukser:

vastaavat seuraavien standardien ja muiden ohjeellisten

dokumenttien vaatimuksia edellyttäen, että niitä käytetään

ohjeidemme mukaisesti:

za předpokladu, že jsou využívány v souladu s našimi pokyny,

odpovídají následujícím normám nebo normativním

dokumentům:

u skladu sa slijedećim standardom(ima) ili drugim normativnim

dokumentom(ima), uz uvjet da se oni koriste u skladu s našim

uputama:

megfelelnek az alábbi szabvány(ok)nak vagy egyéb irányadó

dokumentum(ok)nak, ha azokat előírás szerint használják:

spełniają wymogi następujących norm i innych dokumentów

normalizacyjnych, pod warunkiem że używane są zgodnie z

naszymi instrukcjami:

sunt în conformitate cu următorul (următoarele) standard(e) sau

alt(e) document(e) normativ(e), cu condiţia ca acestea să fie

utilizate în conformitate cu instrucţiunile noastre:

skladni z naslednjimi standardi in drugimi normativi, pod

pogojem, da se uporabljajo v skladu z našimi navodili:

on vastavuses järgmis(t)e standardi(te)ga või teiste

normatiivsete dokumentidega, kui neid kasutatakse vastavalt

meie juhenditele:

съответстват на следните стандарти или други нормативни

документи, при условие, че се използват съгласно нашите

инструкции:

atitinka žemiau nurodytus standartus ir (arba) kitus norminius

dokumentus su sąlyga, kad yra naudojami pagal mūsų

nurodymus:

tad, ja lietoti atbilstoši ražotāja norādījumiem, atbilst sekojošiem

standartiem un citiem normatīviem dokumentiem:

sú v zhode s nasledovnou(ými) normou(ami) alebo iným(i)

normatívnym(i) dokumentom(ami), za predpokladu, že sa

používajú v súlade s našim návodom:

ürünün, talimatlarımıza göre kullanılması koşuluyla aşağıdaki

standartlar ve norm belirten belgelerle uyumludur:

Directives, as amended.

Direktiven, gemäß Änderung.

Directives, telles que modifiées.

Richtlijnen, zoals geamendeerd.

Directivas, según lo enmendado.

Direttive, come da modifica.

Οδηγιών, όπως έχουν τροποποιηθεί.

Directivas, conforme alteração em.

Директив со всеми поправками.

Direktiver, med senere ændringer.

Direktiv, med företagna ändringar.

Direktiver, med foretatte endringer.

Direktiivejä, sellaisina kuin ne ovat muutettuina.

v platném znění.

Smjernice, kako je izmijenjeno.

irányelv(ek) és módosításaik rendelkezéseit

z późniejszymi poprawkami.

Directivelor, cu amendamentele respective.

Direktive z vsemi spremembami.

Direktiivid koos muudatustega.

Директиви, с техните изменения.

Direktyvose su papildymais.

Direktīvās un to papildinājumos.

Smernice, v platnom znení.

Deǧiştirilmiş halleriyle Yönetmelikler.

following the provisions of:

gemäß den Vorschriften der:

conformément aux stipulations des:

overeenkomstig de bepalingen van:

siguiendo las disposiciones de:

secondo le prescrizioni per:

με τήρηση των διατάξεων των:

de acordo com o previsto em:

в соответствии с положениями:

under iagttagelse af bestemmelserne i:

enligt villkoren i:

gitt i henhold til bestemmelsene i:

noudattaen määräyksiä:

za dodržení ustanovení předpisu:

prema odredbama:

követi a(z):

zgodnie z postanowieniami Dyrektyw:

în urma prevederilor:

ob upoštevanju določb:

vastavalt nõuetele:

следвайки клаузите на:

laikantis nuostatų, pateikiamų:

ievērojot prasības, kas noteiktas:

održiavajúc ustanovenia:

bunun koşullarına uygun olarak:

01 *

as set out in

<A>

and judged positively by

according to the

Certificate <C>

** as set out in the Technical Construction File

<D>

and judged

positively by

<E>

(Applied module

<F>

) according to the

certificate

<G>

. Risk category

<H>

. Also refer to next page.

02 *

wie in

<A>

aufgeführt und von

positiv beurteilt gemäß

Zertifikat <C>

** wie in der Technischen Konstruktionsakte

<D>

aufgeführt und

von

<E>

(Angewandtes Modul

<F>

) positiv ausgezeichnet gemäß

Zertifikat <G>

. Risikoart

<H>

. Siehe auch nächste Seite.

03 *

tel que défini dans

<A>

et évalué positivement par

conformément au

Certificat <C>

** tel que stipulé dans le Fichier de Construction Technique

<D>

et jugé

positivement par

<E>

(Module appliqué

<F>

) conformément au

Certificat <G>

. Catégorie de risque

<H>

. Se reporter également

à la page suivante.

04 *

zoals vermeld in

<A>

en positief beoordeeld door

overeenkomstig

Certificaat <C>

** zoals vermeld in het Technisch Constructiedossier

<D>

en in orde

bevonden door

<E>

(Toegepaste module

<F>

) overeenkomstig

Certificaat <G>

. Risicocategorie

<H>

. Zie ook de volgende pagina.

05 *

como se establece en

<A>

y es valorado positivamente por

de acuerdo con el

Certificado <C>

** tal como se expone en el Archivo de Construcción Técnica

<D>

y juzgado positivamento por

<E>

(Modulo aplicado

<F>

) según

Certificado <G>

. Categoría de riesgo

<H>

. Consulte también

la siguiente página.

06 *

delineato nel

<A>

e giudicato positivamente da

secondo

Certificato <C>

** delineato nel File Tecnico di Costruzione

<D>

e giudicato

positivamente da

<E>

(Modulo

<F>

applicato) secondo il

Certificato <G>

. Categoria di rischio

<H>

. Fare riferimento

anche alla pagina successiva.

07 *

όπως καθορίζεται στο

<A>

και κρίνεται θετικά από το

σύμφωνα

με το

Πιστοποιητικό <C>

** όπως προσδιορίζεται στο Αρχείο Τεχνικής Κατασκευής

<D>

και

κρίνεται θετικά από το

<E>

(Χρησιμοποιούμενη υπομονάδα

<F>

)

σύμφωνα με το

Πιστοποιητικό <G>

. Κατηγορία επικινδυνότητας

<H>

. Ανατρέξτε επίσης στην επόμενη σελίδα.

08 *

tal como estabelecido em

<A>

e com o parecer positivo de

de acordo com o

Certificado <C>

** tal como estabelecido no Ficheiro Técnico de Construção

<D>

e com o parecer positivo de

<E>

(Módulo aplicado

<F>

) de acordo

com o

Certificado <G>

. Categoria de risco

<H>

. Consultar também

a página seguinte.

09 *

как указано в

<A>

и в соответствии с положительным решением

согласно

Свидетельству <C>

** как указано в Досье технического топкования

<D>

и в соответствии

с положительным решением

<E>

(Прикладной модуль

<F>

) согласно

Свидетельству <G>

. Категория риска

<H>

. Также смотрите

следующую страницу.

10 *

som anført i

<A>

og positivt vurderet af

i henhold tilPressure

Equipment 97/23/EC

Certifikat <C>

som anført i den Tekniske Konstruktionsfil

<D>

og positivt vurderet af

<E>

(Anvendt modul

<F>

)

i henhold til

Certifikat

<G>

. Risikoklasse

<H>

Se også næste side.

11 *

enligt

<A>

och godkänts av

enligt

Certifikatet <C>

** i enlighet med den Tekniska Konstruktionsfilen

<D>

som positivt

intygats av

<E>

(Fastsatt modul

<F>

) vilket också framgår av

Certifikat <G>

. Riskkategori

<H>

. Se även nästa sida.

12 *

som det fremkommer i

<A>

og gjennom positiv bedømmelse av

ifølge

Sertifikat <C>

** som det fremkommer i den Tekniske Konstruksjonsfilen

<D>

gjennom positiv bedømmelse av

<E>

(Anvendt modul

<F>

) ifølge

Sertifikat <G>

. Risikokategori

<H>

. Se også neste side.

13 *

jotka on esitetty asiakirjassa

<A>

ja jotka

on hyväksynyt

Sertifikaatin <C>

mukaisesti.

** jotka on esitetty Teknisessä Asiakirjassa

<D>

ja jotka

<E>

hyväksynyt (Sovellettu moduli

<F>

)

Sertifikaatin <G>

mukaisesti.

Vaaraluokka

<H>

. Katso myös seuraava sivu.

14 *

jak bylo uvedeno v

<A>

a pozitivně zjištěno

v souladu

osvědčením <C>

** jak bylo uvedeno v souboru technické konstrukce

<D>

a pozitivně

zjištěno

<E>

(použitý modul

<F>

) v souladu s

osvědčením <G>

Kategorie rizik

<H>

. Viz také následující strana.

15 *

kako je izloženo u

<A>

i pozitivno ocijenjeno od strane

prema

Certifikatu <C>

** kako je izloženo u Datoteci o tehničkoj konstrukciji

<D>

i pozitivno

ocijenjeno od strane

<E>

(Primijenjen modul

<F>

) prema

Certifikatu <G>

. Kategorija opasnosti

<H>.

Također pogledajte

na slijedećoj stranici.

16 *

a(z)

<A>

alapján, a(z)

igazolta a megfelelést, a(z)

<C> tanúsítvány

szerint.

** a(z)

<D>

műszaki konstrukciós dokumentáció alapján, a(z)

<E>

igazolta a megfelelést (alkalmazott modul:

<F>

), a(z)

<G> tanúsítvány

szerint. Veszélyességi kategória

<H>

Lásd még a következő oldalon.

17 *

zgodnie z dokumentacją

<A>

, pozytywną opinią

Świadectwem <C>

** zgodnie z archiwalną dokumentacją konstrukcyjną

<D>

i pozytywną opinią

<E>

(Zastosowany moduł

<F>

) zgodnie

Świadectwem <G>

. Kategoria zagrożenia

<H>

. Patrz

także następna strona.

18 *

aşa cum este stabilit în

<A>

şi apreciat pozitiv de

în conformitate

Certificatul <C>

** conform celor stabilite în Dosarul tehnic de construcţie

<D>

şi apreciate pozitiv de

<E>

(Modul aplicat

<F>

) în conformitate

Certificatul <G>

. Categorie de risc

<H>

. Consultaţi de asemenea

pagina următoare.

19 *

kot je določeno v

<A>

in odobreno s strani

v skladu

certifikatom <C>

** kot je določeno v tehnični mapi

<D>

in odobreno s strani

<E>

(Uporabljen modul

<F>

) v skladu s

certifikatom <G>

. Kategorija

tveganja

<H>

. Glejte tudi na naslednji strani.

20 *

nagu on näidatud dokumendis

<A>

ja heaks kiidetud

järgi

vastavalt

sertifikaadile <C>

** nagu on näidatud tehnilises dokumentatsioonis

<D>

ja heaks kiidetud

<E>

järgi (lisamoodul

<F>

) vastavalt

sertifikaadile <G>

Riskikategooria

<H>

. Vaadake ka järgmist lehekülge.

* както е изложено в

<A>

и оценено положително от

съгласно

Сертификата <C>

** както е заложено в Акта за техническа конструкция

<D>

оценено положително от

<E>

(Приложен модул

<F>

) съгласно

Сертификат <G>

. Категория риск

<H>

. Вижте също на

следващата страница.

22 *

kaip nustatyta

<A>

ir kaip teigiamai nuspręsta

pagal

Sertifikatą <C>

** kaip nurodyta Techninėje konstrukcijos byloje

<D>

ir patvirtinta

<E>

(taikomas modulis

<F>

) pagal pažymėjimą

<G>

. Rizikos kategorija

<H>

. Taip pat žiūrėkite ir kitą puslapį.

23 *

kā norādīts

<A>

un atbilstoši

pozitīvajam vērtējumam saskaņā

sertifikātu <C>

** kā noteikts tehniskajā dokumentācijā

<D>

, atbilstoši

<E>

pozitīvajam

lēmumam (piekritīgā sadaĮa:

<F>

), ko apliecina

sertifikāts <G>

Riska kategorija

<H>

. Skat. arī nākošo lappusi.

24 *

ako bolo uvedené v

<A>

a pozitívne zistené

v súlade

osvedčením <C>

** ako je to stanovené v Súbore technickej konštrukcie

<D>

a kladne

posúdené

<E>

(Aplikovaný modul

<F>

) podľa

Certifikátu <G>

Kategória nebezpečia

<H>

. Viď tiež nasledovnú stranu.

25 * <A>

’da belirtildiği gibi ve

<C> Sertifikasına

göre

tarafından

olumlu olarak değerlendirildiği gibi.

<D>

Teknik Yapı Dosyasında belirtildiği gibi ve

<G> Sertifikasına

göre

<E>

tarafından olumlu olarak (Uygulanan modül

<F>

)

değerlendirilmiştir.

<G>

. Risk kategorisi

<H>

. Ayrıca bir sonraki

sayfaya bakın.

<A> DAIKIN.TCF.032C7/12-2015

DEKRA (NB0344)

<C> 2159619.0551-EMC

<D> TCF-CZ15003-02

<E> AIB Vinçotte (NB0026)

<F> D1

<G> 100379113/1115

<H>

declares under its sole responsibility that the air conditioning models to which this declaration relates:

erklärt auf seine alleinige Verantwortung daß die Modelle der Klimageräte für die diese Erklärung bestimmt ist:

déclare sous sa seule responsabilité que les appareils d'air conditionné visés par la présente déclaration:

verklaart hierbij op eigen exclusieve verantwoordelijkheid dat de airconditioning units waarop deze verklaring betrekking heeft:

declara baja su única responsabilidad que los modelos de aire acondicionado a los cuales hace referencia la declaración:

dichiara sotto sua responsabilità che i condizionatori modello a cui è riferita questa dichiarazione:

δηλώνει με αποκλειστική της ευθύνη ότι τα μοντέλα των κλιματιστικών συσκευών στα οποία αναφέρεται η παρούσα δήλωση:

declara sob sua exclusiva responsabilidade que os modelos de ar condicionado a que esta declaração se refere:

заявляет, исключительно под свою ответственность, что модели кондиционеров воздуха, к которым относится настоящее заявление:

erklærer under eneansvar, at klimaanlægmodellerne, som denne deklaration vedrører:

deklarerar i egenskap av huvudansvarig, att luftkonditioneringsmodellerna som berörs av denna deklaration innebär att:

erklærer et fullstendig ansvar for at de luftkondisjoneringsmodeller som berøres av denne deklarasjonen, innebærer at:

ilmoittaa yksinomaan omalla vastuullaan, että tämän ilmoituksen tarkoittamat ilmastointilaitteiden mallit:

prohlašuje ve své plné odpovědnosti, že modely klimatizace, k nimž se toto prohlášení vztahuje:

izjavljuje pod isključivo vlastitom odgovornošću da su modeli klima uređaja na koje se ova izjava odnosi:

teljes felelőssége tudatában kijelenti, hogy a klímaberendezés modellek, melyekre e nyilatkozat vonatkozik:

deklaruje na własną i wyłączną odpowiedzialność, że modele klimatyzatorów, których dotyczy niniejsza deklaracja:

declară pe proprie răspundere că aparatele de aer condiţionat la care se referă această declaraţie:

z vso odgovornostjo izjavlja, da so modeli klimatskih naprav, na katere se izjava nanaša:

kinnitab oma täielikul vastutusel, et käesoleva deklaratsiooni alla kuuluvad kliimaseadmete mudelid:

декларира на своя отговорност, че моделите климатична инсталация, за които се отнася тази декларация:

visiška savo atsakomybe skelbia, kad oro kondicionavimo prietaisų modeliai, kuriems yra taikoma ši deklaracija:

ar pilnu atbildību apliecina, ka tālāk uzskaitīto modeļu gaisa kondicionētāji, uz kuriem attiecas šī deklarācija:

vyhlasuje na vlastnú zodpovednosť, že tieto klimatizačné modely, na ktoré sa vzťahuje toto vyhlásenie:

tamamen kendi sorumluluǧunda olmak üzere bu bildirinin ilgili olduǧu klima modellerinin aşaǧıdaki gibi olduǧunu beyan eder:

2P427092-2D

3MXM40M2V1B, 3MXM52M2V1B, 3AMXM52M2V1B,

EN60335-2-40

01 ***

DICz

is authorised to compile the Technical Construction File.

02 ***

DICz

hat die Berechtigung die Technische Konstruktionsakte zusammenzustellen.

03 ***

DICz

est autorisé à compiler le Dossier de Construction Technique.

04 ***

DICz

is bevoegd om het Technisch Constructiedossier samen te stellen.

05 ***

DICz

está autorizado a compilar el Archivo de Construcción Técnica.

06 ***

DICz

è autorizzata a redigere il File Tecnico di Costruzione.

07 ***

Η DICz

είναι εξουσιοδοτημένη να συντάξει τον Τεχνικό φάκελο κατασκευής.

08 ***

A DICz

está autorizada a compilar a documentação técnica de fabrico.

09 ***

Компания DICz

уполномочена составить Комплект технической документации.

10 ***

DICz

er autoriseret til at udarbejde de tekniske konstruktionsdata.

11 ***

DICz

är bemyndigade att sammanställa den tekniska konstruktionsfilen.

12 ***

DICz

har tillatelse til å kompilere den Tekniske konstruksjonsfilen.

13 ***

DICz

on valtuutettu laatimaan Teknisen asiakirjan.

14 ***

Společnost DICz

má oprávnění ke kompilaci souboru technické konstrukce.

15 ***

DICz

je ovlašten za izradu Datoteke o tehničkoj konstrukciji.

16 ***

A DICz

jogosult a műszaki konstrukciós dokumentáció összeállítására.

17 ***

DICz

ma upoważnienie do zbierania i opracowywania dokumentacji konstrukcyjnej.

18 ***

DICz

este autorizat să compileze Dosarul tehnic de construcţie.

19 ***

DICz

je pooblaščen za sestavo datoteke s tehnično mapo.

20 ***

DICz

on volitatud koostama tehnilist dokumentatsiooni.

21 ***

DICz

е оторизирана да състави Акта за техническа конструкция.

22 ***

DICz

yra įgaliota sudaryti šį techninės konstrukcijos failą.

23 ***

DICz

ir autorizēts sastādīt tehnisko dokumentāciju.

24 ***

Spoločnosť DICz

je oprávnená vytvoriť súbor technickej konštrukcie.

25 ***

DICz

Teknik Yapı Dosyasını derlemeye yetkilidir.

DICz = Daikin Industries Czech Republic s.r.o.

Machinery 2006/42/EC

Electromagnetic Compatibility 2004/108/EC

Pressure Equipment 97/23/EC

Low Voltage 2006/95/EC

***

Downloaded from www.Manualslib.com manuals search engine

CE - DECLARATION-OF-CONFORMITY

CE - KONFORMITÄTSERKLÄRUNG

CE - DECLARATION-DE-CONFORMITE

CE - CONFORMITEITSVERKLARING

CE - DECLARACION-DE-CONFORMIDAD

CE - DICHIARAZIONE-DI-CONFORMITA

CE - ΔHΛΩΣΗ ΣΥΜΜΟΡΦΩΣΗΣ

CE - DECLARAÇÃO-DE-CONFORMIDADE

CE - ЗАЯВЛЕНИЕ-О-СООТВЕТСТВИИ

CE - OVERENSSTEMMELSESERKLÆRING

CE - FÖRSÄKRAN-OM-ÖVERENSTÄMMELSE

CE - ERKLÆRING OM-SAMSVAR

CE - ILMOITUS-YHDENMUKAISUUDESTA

CE - PROHLÁŠENÍ-O-SHODĚ

CE - IZJAVA-O-USKLAĐENOSTI

CE - MEGFELELŐSÉGI-NYILATKOZAT

CE - DEKLARACJA-ZGODNOŚCI

CE - DECLARAŢIE-DE-CONFORMITATE

CE - IZJAVA O SKLADNOSTI

CE - VASTAVUSDEKLARATSIOON

CE - ДЕКЛАРАЦИЯ-ЗА-ϹЪОТВЕТСТВИЕ

CE - ATITIKTIES-DEKLARACIJA

CE - ATBILSTĪBAS-DEKLARĀCIJA

CE - VYHLÁSENIE-ZHODY

CE - UYGUNLUK-BEYANI

• Maximum allowable pressure (PS):

<K>

(bar)

• Minimum/maximum allowable temperature (TS*):

* TSmin: Minimum temperature at low pressure side:

<L>

(°C)

* TSmax: Saturated temperature corresponding with the maximum

allowable pressure (PS):

<M>

(°C)

• Refrigerant:

<N>

• Setting of pressure safety device:

(bar)

• Manufacturing number and manufacturing year: refer to model

nameplate

• Maximal zulässiger Druck (PS):

<K>

(Bar)

• Minimal/maximal zulässige Temperatur (TS*):

* TSmin: Mindesttemperatur auf der Niederdruckseite:

<L>

(°C)

* TSmax: Sättigungstemperatur die dem maximal zulässigen Druck

(PS) entspricht:

<M>

(°C)

• Kältemittel:

<N>

• Einstellung der Druck-Schutzvorrichtung:

(Bar)

• Herstellungsnummer und Herstellungsjahr: siehe Typenschild

des Modells

• Pression maximale admise (PS):

<K>

(bar)

• Température minimum/maximum admise (TS*):

* TSmin: température minimum côté basse pression:

<L>

(°C)

* TSmax: température saturée correspondant à la pression

maximale admise (PS):

<M>

(°C)

• Réfrigérant:

<N>

• Réglage du dispositif de sécurité de pression:

(bar)

• Numéro de fabrication et année de fabrication: se reporter à la

plaquette signalétique du modèle

• Maximaal toelaatbare druk (PS):

<K>

(bar)

• Minimaal/maximaal toelaatbare temperatuur (TS*):

* TSmin: Minimumtemperatuur aan lagedrukzijde:

<L>

(°C)

* TSmax: Verzadigde temperatuur die overeenstemt met de

maximaal toelaatbare druk (PS):

<M>

(°C)

• Koelmiddel:

<N>

• Instelling van drukbeveiliging:

(bar)

• Fabricagenummer en fabricagejaar: zie naamplaat model

• Presión máxima admisible (PS):

<K>

(bar)

• Temperatura mínima/máxima admisible (TS*):

* TSmin: Temperatura mínima en el lado de baja presión:

<L>

(°C)

* TSmax: Temperatura saturada correspondiente a la presión

máxima admisible (PS):

<M>

(°C)

• Refrigerante:

<N>

• Ajuste del presostato de seguridad:

(bar)

• Número de fabricación y año de fabricación: consulte la placa

de especificaciones técnicas del modelo

• Pressione massima consentita (PS):

<K>

(bar)

• Temperatura minima/massima consentita (TS*):

* TSmin: temperatura minima nel lato di bassa pressione:

<L>

(°C)

* TSmax: temperatura satura corrispondente alla pressione

massima consentita (PS):

<M>

(°C)

• Refrigerante:

<N>

• Impostazione del dispositivo di controllo della pressione:

(bar)

• Numero di serie e anno di produzione: fare riferimento alla targhetta

del modello

• Mέγιστη επιτρεπόμενη πίεση (PS):

<K>

(bar)

• Ελάχιστη/μέγιστη επιτρεπόμενη θερμοκρασία (TS*):

* TSmin: Ελάχιστη θερμοκρασία για την πλευρά χαμηλής πίεσης:

<L>

(°C)

* TSmax: Κορεσμένη θερμοκρασία που αντιστοιχεί με τη μέγιστη

επιτρεπόμενη πίεση (PS):

<M>

(°C)

•Ψυκτικό:

<N>

• Ρύθμιση της διάταξης ασφάλειας πίεσης:

(bar)

• Αριθμός κατασκευής και έτος κατασκευής: ανατρέξτε στην πινακίδα

αναγνώρισης του μοντέλου

• Pressão máxima permitida (PS):

<K>

(bar)

• Temperaturas mínima e máxima permitidas (TS*):

* TSmin: Temperatura mínima em baixa pressão:

<L>

(°C)

* TSmax: Temperatura de saturação correspondente à pressão

máxima permitida (PS):

<M>

(°C)

• Refrigerante:

<N>

• Regulação do dispositivo de segurança da pressão:

(bar)

• Número e ano de fabrico: consultar a placa de especificações

da unidade

• Максимально допустимое давление (PS):

<K>

(бар)

• Минимально/Максимально допустимая температура (TS*):

* TSmin: Минимальная температура на стороне низкого

давления:

<L>

(°C)

* TSmax: Температура кипения, соответствующая максимально

допустимому давлению (PS):

<M>

(°C)

•Хладагент:

<N>

• Настройка устройства защиты по давлению:

(бар)

• Заводской номер и год изготовления: смотрите паспортную

табличку модели

• Maks. tilladt tryk (PS):

<K>

(bar)

• Min./maks. tilladte temperatur (TS*):

* TSmin: Min. temperatur på lavtrykssiden:

<L>

(°C)

* TSmax: Mættet temperatur svarende til maks. tilladte tryk (PS):

<M>

(°C)

• Kølemiddel:

<N>

• Indstilling af tryksikringsudstyr:

(bar)

• Produktionsnummer og fremstillingsår: se modellens fabriksskilt

• Maximalt tillåtet tryck (PS):

<K>

(bar)

• Min/max tillåten temperatur (TS*):

* TSmin: Minimumtemperatur på lågtryckssidan:

<L>

(°C)

* TSmax: Mättnadstemperatur som motsvarar maximalt tillåtet tryck

(PS):

<M>

(°C)

• Köldmedel:

<N>

• Inställning för trycksäkerhetsenhet:

(bar)

• Tillverkningsnummer och tillverkningsår: se modellens namnplåt

• Maksimalt tillatt trykk (PS):

<K>

(bar)

• Minimalt/maksimalt tillatt temperatur (TS*):

* TSmin: Minimumstemperatur på lavtrykkssiden:

<L>

(°C)

* TSmax: Metningstemperatur i samsvar med maksimalt tillatt trykk

(PS):

<M>

(°C)

• Kjølemedium:

<N>

• Innstilling av sikkerhetsanordning for trykk:

(bar)

• Produksjonsnummer og produksjonsår: se modellens merkeplate

• Suurin sallittu paine (PS):

<K>

(bar)

• Pienin/suurin sallittu lämpötila (TS*):

* TSmin: Alhaisin matalapainepuolen lämpötila:

<L>

(°C)

* TSmax: Suurinta sallittua painetta (PS) vastaava

kyllästyslämpötila:

<M>

(°C)

• Kylmäaine:

<N>

• Varmuuspainelaitteen asetus:

(bar)

• Valmistusnumero ja valmistusvuosi: katso mallin nimikilpi

• Maximální přípustný tlak (PS):

<K>

(bar)

• Minimální/maximální přípustná teplota (TS*):

* TSmin: Minimální teplota na nízkotlaké straně:

<L>

(°C)

* TSmax: Saturovaná teplota odpovídající maximálnímu

přípustnému tlaku (PS):

<M>

(°C)

• Chladivo:

<N>

• Nastavení bezpečnostního tlakového zařízení:

(bar)

• Výrobní číslo a rok výroby: viz typový štítek modelu

• Najveći dopušten tlak (PS):

<K>

(bar)

• Najniža/najviša dopuštena temperatura (TS*):

* TSmin: Najniža temperatura u području niskog tlaka:

<L>

(°C)

* TSmax: Standardna temperatura koja odgovara najvećem

dopuštenom tlaku (PS):

<M>

(°C)

• Rashladno sredstvo:

<N>

• Postavke sigurnosne naprave za tlak:

(bar)

• Proizvodni broj i godina proizvodnje: pogledajte natpisnu pločicu

modela

• Legnagyobb megengedhető nyomás (PS):

<K>

(bar)

• Legkisebb/legnagyobb megengedhető hőmérséklet (TS*):

* TSmin: Legkisebb megengedhető hőmérséklet a kis nyomású

oldalon:

<L>

(°C)

* TSmax: A legnagyobb megengedhető nyomásnak (PS) megfelelő

telítettségi hőmérséklet:

<M>

(°C)

• Hűtőközeg:

<N>

• A túlnyomás-kapcsoló beállítása:

(bar)

• Gyártási szám és gyártási év: lásd a berendezés adattábláján

• Maksymalne dopuszczalne ciśnienie (PS):

<K>

(bar)

• Minimalna/maksymalna dopuszczalna temperatura (TS*):

* TSmin: Minimalna temperatura po stronie niskociśnieniowej:

<L>

(°C)

* TSmax: Temperatura nasycenia odpowiadająca maksymalnemu

dopuszczalnemu ciśnieniu (PS):

<M>

(°C)

• Czynnik chłodniczy:

<N>

• Nastawa ciśnieniowego urządzenia bezpieczeństwa:

(bar)

• Numer fabryczny oraz rok produkcji: patrz tabliczka znamionowa

modelu

• Presiune maximă admisibilă (PS):

<K>

(bar)

• Temperatură minimă/maximă admisibilă (TS*):

* TSmin: Temperatură minimă pe partea de presiune joasă:

<L>

(°C)

* TSmax: Temperatură de saturaţie corespunzând presiunii maxime

admisibile (PS):

<M>

(°C)

• Agent frigorific:

<N>

• Reglarea dispozitivului de siguranţă pentru presiune:

(bar)

• Numărul de fabricaţie şi anul de fabricaţie: consultaţi placa de

identificare a modelului

• Maksimalni dovoljeni tlak (PS):

<K>

(bar)

• Minimalna/maksimalna dovoljena temperatura (TS*):

* TSmin: Minimalna temperatura na nizkotlačni strani:

<L>

(°C)

* TSmax: Nasičena temperatura, ki ustreza maksimalnemu

dovoljenemu tlaku (PS):

<M>

(°C)

• Hladivo:

<N>

• Nastavljanje varnostne naprave za tlak:

(bar)

• Tovarniška številka in leto proizvodnje: glejte napisno ploščico

• Maksimaalne lubatud surve (PS):

<K>

(bar)

• Minimaalne/maksimaalne lubatud temperatuur (TS*):

* TSmin: Minimaalne temperatuur madalsurve küljel:

<L>

(°C)

* TSmax: Maksimaalsele lubatud survele (PS) vastav küllastunud

temperatuur:

<M>

(°C)

• Jahutusaine:

<N>

• Surve turvaseadme seadistus:

(bar)

• Tootmisnumber ja tootmisaasta: vaadake mudeli andmeplaati

• Максимално допустимо налягане (PS):

<K>

(bar)

• Минимално/максимално допустима температура (TS*):

* TSmin: Минимална температура от страната на ниското

налягане:

<L>

(°C)

* TSmax: Температура на насищане, съответстваща на

максимално допустимото налягане (PS):

<M>

(°C)

•Охладител:

<N>

• Настройка на предпазното устройство за налягане:

(bar)

• Фабричен номер и година на производство: вижте табелката

на модела

• Maksimalus leistinas slėgis (PS):

<K>

(bar)

• Minimali/maksimali leistina temperatūra (TS*):

* TSmin: Minimali temperatūra žemo slėgio pusėje:

<L>

(°C)

* TSmax: Prisotinta temperatūra, atitinkamti maksimalų leistiną slėgį

(PS):

<M>

(°C)

• Šaldymo skystis:

<N>

• Apsauginio slėgio prietaiso nustatymas:

(bar)

• Gaminio numeris ir pagaminimo metai: žiūrėkite modelio pavadinimo

plokštelę

• Maksimālais pieļaujamais spiediens (PS):

<K>

(bar)

• Minimālā/maksimālā pieļaujamā temperatūra (TS*):

* TSmin: Minimālā temperatūra zemā spiediena pusē:

<L>

(°C)

* TSmax: Piesātinātā temperatūra saskaņā ar maksimālo

pieļaujamo spiedienu (PS):

<M>

(°C)

• Dzesinātājs:

<N>

• Spiediena drošības ierīces iestatīšana:

(bar)

• Izgatavošanas numurs un izgatavošanas gads: skat. modeļa

izgatavotājuzņēmuma plāksnītie

• Maximálny povolený tlak (PS):

<K>

(bar)

• Minimálna/maximálna povolená teplota (TS*):

* TSmin: Minimálna teplota na nízkotlakovej strane:

<L>

(°C)

* TSmax: Nasýtená teplota korešpondujúca s maximálnym

povoleným tlakom (PS):

<M>

(°C)

• Chladivo:

<N>

• Nastavenie tlakového poistného zariadenia:

(bar)

• Výrobné číslo a rok výroby: nájdete na výrobnom štítku modelu

• İzin verilen maksimum basınç (PS):

<K>

(bar)

• İzin verilen minimum/maksimum sıcaklık (TS*):

* TSmin: Düşük basınç tarafındaki minimum sıcaklık:

<L>

(°C)

* TSmax: İzin verilen maksimum basınca (PS) karşı gelen doyma

sıcaklığı:

<M>

(°C)

• Soğutucu:

<N>

• Basınç emniyet düzeninin ayarı:

(bar)

• İmalat numarası ve imalat yılı: modelin ünite plakasına bakın

<K> PS 41.7 bar

<L> TSmin -35 °C

<M> TSmax 63.8 °C

<N> R32

41.7 bar

continuation of previous page:

Fortsetzung der vorherigen Seite:

suite de la page précédente:

vervolg van vorige pagina:

continuación de la página anterior:

continua dalla pagina precedente:

συνέχεια από την προηγούμενη σελίδα:

continuação da página anterior:

продолжение предыдущей страницы:

fortsat fra forrige side:

fortsättning från föregående sida:

fortsettelse fra forrige side:

jatkoa edelliseltä sivulta:

pokračování z předchozí strany:

nastavak s prethodne stranice:

folytatás az előző oldalról:

ciąg dalszy z poprzedniej strony:

continuarea paginii anterioare:

nadaljevanje s prejšnje strani:

eelmise lehekülje järg:

продължение от предходната страница:

ankstesnio puslapio tęsinys:

iepriekšējās lappuses turpinājums:

pokračovanie z predchádzajúcej strany:

önceki sayfadan devam:

2P427092-2D

Design Specifications of the models to which this declaration relates:

Konstruktionsdaten der Modelle auf die sich diese Erklärung bezieht:

Spécifications de conception des modèles auxquels se rapporte cette déclaration:

Ontwerpspecificaties van de modellen waarop deze verklaring betrekking heeft:

Especificaciones de diseño de los modelos a los cuales hace referencia esta

declaración:

Specifiche di progetto dei modelli cui fa riferimento la presente dichiarazione:

Προδιαγραφές Σχεδιασμού των μοντέλων με τα οποία σχετίζεται η δήλωση:

Especificações de projecto dos modelos a que se aplica esta declaração:

Проектные характеристики моделей, к которым относится настоящее

заявление:

Typespecifikationer for de modeller, som denne erklæring vedrører:

Designspecifikationer för de modeller som denna deklaration gäller:

Konstruksjonsspesifikasjoner for de modeller som berøres av denne deklarasjonen:

Tätä ilmoitusta koskevien mallien rakennemäärittely:

Specifikace designu modelů, ke kterým se vztahuje toto prohlášení:

Specifikacije dizajna za modele na koje se ova izjava odnosi:

A jelen nyilatkozat tárgyát képező modellek tervezési jellemzői:

Specyfikacje konstrukcyjne modeli, których dotyczy deklaracja:

Specificaţiile de proiectare ale modelelor la care se referă această declaraţie:

Specifikacije tehničnega načrta za modele, na katere se nanaša ta deklaracija:

Deklaratsiooni alla kuuluvate mudelite disainispetsifikatsioonid:

Проектни спецификации на моделите, за които се отнася декларацията:

Konstrukcinės specifikacijos modelių, kurie susiję su šia deklaracija:

To modeļu dizaina specifikācijas, uz kurām attiecas šī deklarācija:

Konštrukčné špecifikácie modelu, ktorého sa týka toto vyhlásenie:

Bu bildirinin ilgili olduğu modellerin Tasarım Özellikleri:

Name and address of the Notified body that judged positively

on compliance with the Pressure Equipment Directive:

<Q>

Name und Adresse der benannten Stelle, die positiv unter

Einhaltung der Druckanlagen-Richtlinie urteilte:

<Q>

Nom et adresse de l’organisme notifié qui a évalué positivement

la conformité à la directive sur l’équipement de pression:

<Q>

Naam en adres van de aangemelde instantie die positief geoordeeld

heeft over de conformiteit met de Richtlijn Drukapparatuur:

<Q>

Nombre y dirección del Organismo Notificado que juzgó

positivamente el cumplimiento con la Directiva en materia de

Equipos de Presión:

<Q>

Nome e indirizzo dell’Ente riconosciuto che ha riscontrato la

conformità alla Direttiva sulle apparecchiature a pressione:

<Q>

Όνομα και διεύθυνση του Κοινοποιημένου οργανισμού που

απεφάνθη θετικά για τη συμμόρφωση προς την Οδηγία

Εξοπλισμών υπό Πίεση:

<Q>

Nome e morada do organismo notificado, que avaliou

favoravelmente a conformidade com a directiva sobre

equipamentos pressurizados:

<Q>

Название и адрес органа технической экспертизы,

принявшего положительное решение о соответствии

Директиве об оборудовании под давлением:

<Q>

Navn og adresse på bemyndiget organ, der har foretaget en

positiv bedømmelse af, at udstyret lever op til kravene i PED

(Direktiv for Trykbærende Udstyr):

<Q>

Namn och adress för det anmälda organ som godkänt

uppfyllandet av tryckutrustningsdirektivet:

<Q>

Navn på og adresse til det autoriserte organet som positivt

bedømte samsvar med direktivet for trykkutstyr (Pressure

Equipment Directive):

<Q>

Sen ilmoitetun elimen nimi ja osoite, joka teki myönteisen

päätöksen painelaitedirektiivin noudattamisesta:

<Q>

Název a adresa informovaného orgánu, který vydal pozitivní

posouzení shody se směrnicí o tlakových zařízeních:

<Q>

Naziv i adresa prijavljenog tijela koje je donijelo pozitivnu

prosudbu o usklađenosti sa Smjernicom za tlačnu opremu:

<Q>

A nyomástartó berendezésekre vonatkozó irányelvnek való

megfelelőséget igazoló bejelentett szervezet neve és címe:

<Q>

Nazwa i adres Jednostki notyfikowanej, która wydała pozytywną

opinię dotyczącą spełnienia wymogów Dyrektywy dot. Urządzeń

Ciśnieniowych:

<Q>

Denumirea şi adresa organismului notificat care a apreciat pozitiv

conformarea cu Directiva privind echipamentele sub presiune:

<Q>

Ime in naslov organa za ugotavljanje skladnosti, ki je pozitivno

ocenil združljivost z Direktivo o tlačni opremi:

<Q>

Teavitatud organi, mis hindas Surveseadmete Direktiiviga

ühilduvust positiivselt, nimi ja aadress:

<Q>

Наименование и адрес на упълномощения орган, който

се е произнесъл положително относно съвместимостта

с Директивата за оборудване под налягане:

<Q>

Atsakingos institucijos, kuri davė teigiamą sprendimą pagal

slėginės įrangos direktyvą pavadinimas ir adresas:

<Q>

Sertifikācijas institūcijas, kura ir devusi pozitīvu slēdzienu par

atbilstību Spiediena lekārtu Direktīvai, nosaukums un adrese:

<Q>

Názov a adresa certifikačného úradu, ktorý kladne posúdil zhodu

so smernicou pre tlakové zariadenia:

<Q>

Basınçlı Teçhizat Direktifine uygunluk hususunda olumlu olarak

ğerlendirilen Onaylanm

ş kuruluşun ad

ı ve adresi:

<Q>

<Q> AIB VINÇOTTE INTERNATIONAL

JAN OLIESLAGERSLAAN, 35

1800 VILVOORDE, Belgium

Tetsuya Baba

Managing Director

Pilsen, 1st of Dec. 2015

Downloaded from www.Manualslib.com manuals search engine

1 English

Safety Precautions

• The precautions described herein are classified as WARNING and CAUTION. They both contain important

information regarding safety. Be sure to observe all precautions without fail.

• Meaning of WARNING and CAUTION notices

WARNING .... Failure to follow these instructions properly may result in personal injury or loss of life.

CAUTION ..... Failure to observe these instructions properly may result in property damage or personal injury, which

may be serious depending on the circumstances.

• The safety marks shown in this manual have the following meanings:

• After completing installation, conduct a trial operation to check for faults and explain to the customer how to operate

the air conditioner and take care of it with the aid of the operation manual.

• The original instructions are written in English. All other languages are translations of the original instructions.

Be sure to follow the instructions. Be sure to establish an earth connection. Never attempt.

WARNING

• Ask your dealer or qualified personnel to carry out installation work.

Do not attempt to install the air conditioner yourself. Improper installation may result in water leakage, electric shocks or fire.

• Install the air conditioner in accordance with the instructions in this installation manual.

Improper installation may result in water leakage, electric shocks or fire.

• Be sure to use only the specified accessories and parts for installation work.

Failure to use the specified parts may result in the unit falling, water leakage, electric shocks or fire.

• Install the air conditioner on a foundation strong enough to withstand the weight of the unit.

A foundation of insufficient strength may result in the equipment falling and causing injury.

• Electrical work must be performed in accordance with relevant local and national regulations and with instructions

in this installation manual. Be sure to use a dedicated power supply circuit only.

Insufficiency of power circuit capacity and improper workmanship may result in electric shocks or fire.

• Use a cable of suitable length.

Do not use tapped wires or an extension lead, as this may cause overheating, electric shocks or fire.

• Make sure that all wiring is secured, the specified wires are used, and that there is no strain on the terminal

connections or wires.

Improper connections or securing of wires may result in abnormal heat build-up or fire.

• When wiring the power supply and connecting the wiring between the indoor and outdoor units, position the wires

so that the control box lid can be securely fastened.

Improper positioning of the control box lid may result in electric shocks, fire or over heating terminals.

• If refrigerant gas leaks during installation, ventilate the area immediately.

Toxic gas may be produced if the refrigerant comes into contact with fire.

• After completing installation, check for refrigerant gas leakage.

Toxic gas may be produced if the refrigerant gas leaks into the room and comes into contact with a source of fire, such as a fan heater,

stove or cooker.

• When installing or relocating the air conditioner, be sure to bleed the refrigerant circuit to ensure it is free of air,

and use only the specified refrigerant (R32).

The presence of air or other foreign matter in the refrigerant circuit causes abnormal pressure rise, which may result in equipment damage

and even injury.

• During installation, attach the refrigerant piping securely before running the compressor.

If the refrigerant pipes are not attached and the stop valve is open when the compressor is run, air will be sucked in, causing abnormal

pressure in the refrigeration cycle, which may result in equipment damage and even injury.

• During pump-down, stop the compressor before removing the refrigerant piping.

If the compressor is still running and the stop valve is open during pump-down, air will be sucked in when the refrigerant piping is removed,

causing abnormal pressure in the refrigeration cycle, which may result in equipment damage and even injury.

• Be sure to earth the air conditioner.

Do not earth the unit to a utility pipe, lightning conductor or telephone earth lead. Imperfect earthing may result in electric shocks.

• Be sure to install an earth leakage breaker.

Failure to install an earth leakage breaker may result in electric shocks or fire.

• Do not use means to accelerate the defrosting process or to clean, other than those recommended by the

manufacturer.

• The appliance must be stored in a room without continuously operating ignition sources (for example: open

flames, an operating gas appliance or an operating electric heater).

• Do not pierce or burn.

Read the precautions in this manual

carefully before operating the unit.

This appliance is filled with R32.

Downloaded from www.Manualslib.com manuals search engine

English 2

Safety Precautions

Accessories

Accessories supplied with the outdoor unit:

• Be aware that refrigerants may not contain an odour.

• This appliance must be installed, operated and stored in a room larger than the minimum required floor area.

• Comply with national gas regulations.

CAUTION

• Do not install the air conditioner at any place where there is a danger of flammable gas leakage.

In the event of a gas leakage, build-up of gas near the air conditioner may cause a fire to break out.

• While following the instructions in this installation manual, install drain piping to ensure proper drainage

and insulate piping to prevent condensation.

Improper drain piping may result in indoor water leakage and property damage.

• Tighten the flare nut according to the specified method such as with a torque wrench.

If the flare nut is too tight, it may crack after prolonged use, causing refrigerant leakage.

• Make sure to provide for adequate measures in order to prevent that the outdoor unit be used as a shelter by small

animals.

Small animals making contact with electrical parts can cause malfunctions, smoke or fire. Please instruct the customer to keep the area around

the unit clean.

• The temperature of refrigerant circuit will be high, please keep the inter-unit wire away from copper pipes that are

not thermally insulated.

• This appliance is intended to be used by expert or trained users in shops, in light industry and on farms, or for

commercial and household use by lay persons.

• Sound pressure level is less than 70 dB(A).

• The following information shall be provided at an accessible place of the system:

-instructions for shutting down the system in case of an emergency

-name and address of fire department, police and hospital

-name, address and day & night telephone numbers for obtaining service.

In Europe, EN378 provides the necessary guidance for this logbook.

R32

It is on the bottom of the packing case.

Installation Manual + R32 Manual

A Drain plugB

Reducer assembly

Refrigerant charge label

E Screw bag

(For fixing electrical wire anchor bands)

Multilingual fluorinated greenhouse gases label

F Drain cap (1) G Drain cap (2)H

Downloaded from www.Manualslib.com manuals search engine

3 English

Precautions for Selecting the Location

1) Choose a place solid enough to bear the weight and vibration of the unit, where the operation noise will not be amplified.

2) Choose a location where the hot air discharged from the unit or the operation noise will not cause a nuisance to the neighbours of

the user.

3) Avoid places near a bedroom and the like, so that the operation noise will cause no trouble.

4) There must be sufficient spaces for carrying the unit into and out of the site.

5) There must be sufficient space for air passage and no obstructions around the air inlet and the air outlet.

6) The site must be free from the possibility of flammable gas leakage in a nearby place.

7) Install units, power cords and inter-unit wire at least 3m away from television and radio sets. This is to prevent interference to

images and sounds. (Noises may be heard even if they are more than 3m away depending on radio wave conditions.)

8) In coastal areas or other places with salty atmosphere of sulfate gas, corrosion may shorten the life of the air conditioner.

9) Since water will flow from the drain of the outdoor unit, do not place under the unit anything which must be kept away from mois-

ture.

NOTE

Cannot be installed hanging from ceiling or stacked.

CAUTION

When operating the air conditioner in a low outdoor ambient

temperature, be sure to follow the instructions described below.

• To prevent exposure to wind, install the outdoor unit with its suction

side facing the wall.

• Never install the outdoor unit at a site where the suction side may be

exposed directly to wind.

• To prevent exposure to wind, it is recommended to install a baffle

plate on the air discharge side of the outdoor unit.

• In heavy snowfall areas, select an installation site where the snow

will not affect the unit.

● Construct a large canopy

● Construct a pedestal

Install the unit high enough off the

ground to prevent burying in snow.

Downloaded from www.Manualslib.com manuals search engine

English 4

Indoor/Outdoor Unit

Installation Drawings

For installation of the indoor units, refer to the installation manual which was provided with the units.

(The diagram shows a wall-mounted indoor unit.)

CAUTION

• Do not connect the embedded branch piping and the outdoor unit when only carrying out piping work without connecting the

indoor unit in order to add another indoor unit later.

Make sure no dirt or moisture gets into either side of the embedded branch piping.

See “7 Refrigerant piping work” on page 9 for details.

• It is impossible to connect the indoor unit for one room only. Be sure to connect at least 2 rooms.

Caulk

pipe hole

gap

with putty.

Cut thermal insulation

pipe to an appropriate

length and wrap it with

tape, making sure that no

gap is left in the insulation

pipe’s cut line.

Wrap the insulation

pipe with the finishing

tape from bottom to top.

250mm from wall

Allow space for piping

and electrical servicing.

If there is the danger of the unit falling

or overturning, fix the unit with

foundation bolts, or with wire or other

means.

If the location does not have good

drainage, place the unit on a level

mounting base (or a plastic pedestal).

Install the outdoor unit in a level

position. Failure to do so may result in

water leakage or accumulation.

Level mounting

base (optional parts)

(Foot bolt-

hole centres)

600

Clamping material

Insulation tube

Service lid

Tape

Also insulate the connection on the outdoor unit.

Use tape or insulating material on all connections

to prevent air from getting in between the copper

piping and the insulation tube.

Be sure to do this if the outdoor unit is installed

above.

(Foot bolt-hole

centres)

353

Stop valve cover

Allow 300mm of

work space below

the ceiling surface.

unit: mm

Max. allowable refrigerant charge amount

3MXM40M 2.2kg

3(A)MXM52M 2.2kg

3MXM68M 2.4kg

4MXM68M 2.6kg

4MXM80M 3.0kg

5MXM90M 3.3kg

Refrigerant piping must be kept to

a minimum.

3MXM40M 4.7m

3(A)MXM52M 4.7m

3MXM68M 5.5m

4MXM68M 6.5m

4MXM80M 8.6m

5MXM90M 10.4m

Minimum floor area for installation

The flare connection

should be installed

outdoors.

Refrigerant piping must

be protected from

physical damage.

Install a plastic cover or

equivalent.

Downloaded from www.Manualslib.com manuals search engine

5 English

Installation

• Install the unit horizontally.

• The unit may be installed directly on a concrete verandah or a solid place if drainage is good.

• If the vibration may possibly be transmitted to the building, use a vibration-proof rubber (field supply).

1. Connections (connection port)

Install the indoor unit according to the table below, which shows the relationship between the class of indoor unit and the

corresponding port.

The total indoor unit class that can be connected to this unit:

Precautions on Installation

• Check the strength and level of the installation ground so that the unit will not cause any operating vibration or noise after installed.

• In accordance with the foundation drawing in fix the unit securely by means of the foundation bolts. (Prepare 4 sets of M8 or M10

foundation bolts, nuts and washers each which are available on the market.)

• It is best to screw in the foundation bolts until their ends are 20mm from the foundation surface.

Heat pump type: 3MXM40M* - Up to 7.0kW 4MXM68M* - Up to 11.0kW

3MXM52M* - Up to 9.0kW 4MXM80M* - Up to 14.0kW

3AMXM52M* - Up to 9.0kW 5MXM90M* - Up to 15.5kW

3MXM68M* - Up to 11.0kW

: Use a reducer to connect pipes.

: Use No. 2 and 4 reducers.

: Use No. 5 and 6 reducers.

: Use No. 1 and 3 reducers.

Refer to “How to Use Reducers” on page 10 for information on reducer numbers and their shapes.

Downloaded from www.Manualslib.com manuals search engine

English 6

Outdoor Unit Installation Guideline

• Where a wall or other obstacle is in the path of outdoor unit’s inlet or outlet airflow, follow the installation guidelines below.

• For any of the below installation patterns, the wall height on the exhaust side should be 1200mm or less.

Selecting a Location for Installation of

the Indoor Units

• The maximum allowable length of refrigerant piping, and the maximum allowable height difference between the outdoor and

indoor units, are listed below.

(The shorter the refrigerant piping, the better the performance. Connect so that the piping is as short as possible. Shortest allow-

able length per room is 3m.)

Outdoor unit capacity class

3MXM40M*

3MXM52M*

3AMXM52M*

3MXM68M* 4MXM68M* 4MXM80M* 5MXM90M*

Piping to each indoor unit 25m max. 25m max. 25m max. 25m max. 25m max. 25m max.

Total length of piping between all units 50m max. 50m max. 50m max. 60m max. 70m max. 75m max.

If the outdoor unit is positioned higher than the

indoor units.

If the outdoor unit is positioned otherwise.

(If lower than one or more indoor units)

Wall facing one side

Side view

More than 100

Direction

of air

More than 350

1200

or less

Walls facing two sides

Top view

More than 50 More than 50

than 100

than 350

unit: mm

Walls facing three sides

Top view

More than 50

More than 100

More than 350

Level

difference:

15m max.

Level

difference:

7.5m max.

Indoor Unit

Outdoor Unit

Level

difference:

7.5m max.

Level

difference:

15m max.

Outdoor Unit

Indoor Unit

Downloaded from www.Manualslib.com manuals search engine

7 English

Refrigerant Piping Work

1. Installing outdoor unit

When installing the outdoor unit, refer to “

Precautions for Selecting the Location

” on page 3 and the “

Outdoor Unit Instal-

lation Drawings

” on page 4.

2) If drain work is necessary, follow the procedures below.

2. Drain work

• If the drain port is covered by a mounting base or floor sur-

face, place additional foot bases of at least 1-1/4 inch

(30mm) in height under the outdoor unit’s feet.

• In cold areas, do not use a drain socket, drain caps (1,2)

and a drain hose with the outdoor unit. (Otherwise, the

drain water may freeze, impairing heating performance.)

1) Attach drain cap (1) and drain cap (2).

2) Attach drain socket.

3. Refrigerant piping

CAUTION

• Use the flare nut fixed to the main unit. (To prevent cracking of the flare nut by aged deterioration.)

• To prevent gas leakage, apply refrigeration oil only to the inner surface of the flare. (Use refrigeration oil for R32.)

• Use torque wrenches when tightening the flare nuts to prevent damage to the flare nuts and gas leakage.

• Do not reuse joints which have been used once already.

• Installation shall be done by an installer, the choice of materials and installation shall comply with the applicable legislation. In

Europe the EN378 is the applicable standard that shall be used.

• Ensure that the field piping and connections are not subjected to stress.

Align the centres of both flares and tighten the flare nuts 3 or 4 turns by hand. Then tighten them fully with the torque wrenches.

Drain cap (1)

Drain cap (2)

Air outlet side

Drain

socket

Bottom frame

Drain socket

Hose (available commercially,

inner dia. 5/8 ” (16mm))

Bottom frame

Drain cap

Pinch the bottom

frame in.

Torque wrench

Piping union

Flare nut

Spanner

Flare nut tightening torque

ø 1/4 inch (6.4mm) 10-1/2 — 12-3/4ft ● lbf (14.2-17.2N ● m)

24-1/8 — 29-1/2ft ● lbf (32.7-39.9N ● m)

36-1/2 — 44-1/2ft ● lbf (49.5-60.3N ● m)

45-5/8 — 55-5/8ft ● lbf (61.8-75.4N ● m)

ø 3/8 inch (9.5mm)

ø 1/2 inch (12.7mm)

ø 5/8 inch (15.9mm)

11/16 inch (17mm)

10-1/2 — 12-5/8ft ● lbf

(14.2-17.2N ● m)

8 — 10-7/8ft ● lbf

(10.8-14.7N ● m)

7/8 inch (22mm)

16 — 20-1/4ft ● lbf

(21.6-27.4N ● m)

11/16 inch (27mm)

35-3/8 — 44-1/8ft ● lbf

(48-59.8N ● m)

3/4 inch (19mm)

12-5/8 — 15-3/8ft ● lbf

(17.1-20.9N ● m)

Width across flats

Valve cap tightening

torque

Service port cap tightening torque

Do not apply refrigeration

oil to the outer surface.

Apply refrigeration oil to

the inner surface of the

flare.

Do not apply refrigeration oil to

the flare nut to avoid tightening

with excessive torque.

[Apply oil] [Tighten]

Downloaded from www.Manualslib.com manuals search engine

English 8

Refrigerant Piping Work

4. Evacuating the air with a vacuum pump and checking for gas leakage

WARNING

• Do not mix any substance other than the specified refrigerant (R32) into the refrigeration cycle.

• When refrigerant gas leaks should occur, ventilate the room as soon and as much as possible.

• R32, as well as other refrigerants, should always be recovered and never be released directly into the environment.

• Use a vacuum pump for R32 or R410A exclusively. Using the same vacuum pump for different refrigerants may damage the

vacuum pump or the unit.

• Use tools for R32 or R410A (such as the gauge manifold, charging hose, or vacuum pump adapter).

• During tests never pressurize the appliances with a pressure higher than the maximum allowable pressure (as indicated on the

nameplate of the unit).

• If refrigerant gas leaks, ventilate the area immediately. Toxic gas may be produced if refrigerant gas comes into contact with fire.

• Never directly touch any accidental leaking refrigerant. This could result in severe wounds caused by frostbite.

• When piping work is completed, it is necessary to purge the air and check for gas leakage.

• If using additional refrigerant, perform air purging from the refrigerant pipes and indoor unit using a vacuum pump, then charge

additional refrigerant.

• Use a hexagonal wrench (4mm) to operate the stop valve rod.

• All refrigerant pipe joints should be tightened with a torque wrench to the specified tightening torque.

1) Connect projection side of charging hose (which comes from gauge manifold) to gas stop valve’s service port.

2) Fully open gauge manifold’s low-pressure valve (Lo) and completely close its high-pressure valve (Hi).

(High-pressure valve subsequently requires no operation.)

3) Perform vacuum pumping and make sure that the compound pressure gauge reads –0.1MPa (–76cmHg).

Evacuation for at least 1 hour is recommended.

4) Close gauge manifold’s low-pressure valve (Lo) and stop vacuum pump.

(Keep this state for 4-5 minutes to make sure that the compound pressure gauge pointer does not swing back.

If it does go back, this may indicate the presence of moisture or leaking from connecting parts. After inspecting all the

connection and loosening then retightening the nuts, repeat steps 2-4.)

5) Remove covers from liquid stop valve and gas stop valve.

6) Turn the liquid stop valve’s rod 90 degrees counterclockwise with a hexagonal wrench to open valve.

Close it after 5 seconds, and check for gas leakage.

Using soapy water, check for gas leakage from indoor unit’s flare and outdoor unit’s flare and valve rods.

After the check is complete, wipe all soapy water off.

7) Disconnect charging hose from gas stop valve’s service port, then fully open liquid and gas stop valves.

(Do not attempt to turn valve rod beyond its stop.)

8) Tighten valve caps and service port caps for the liquid and gas stop valves with a torque wrench at the specified torques.

See “3. Refrigerant piping” on page 7 for details.

Downloaded from www.Manualslib.com manuals search engine

9 English

Refrigerant Piping Work

5. Charging with refrigerant

If the total length of piping for all rooms exceeds the figure listed below, additionally charge with

20g

of refrigerant (R32) for

each additional meter of piping.

NOTE:

National implementation of EU regulation on certain fluorinated greenhouse gases may require to provide the appropriate official

national language on the unit. Therefore an additional multilingual fluorinated greenhouse gases label is supplied with the unit.

Sticking instructions are illustrated on the backside of that label.

CAUTION

Even though the stop valve is fully closed, the refrigerant may slowly leak out; do not leave the flare nut removed for a long

period of time.

Outdoor capacity class

3MXM40M, 3MXM52M, 3AMXM52M,

3MXM68M, 4MXM68M, 4MXM80M, 5MXM90M

Total length of piping for all rooms 30m

Please fill in with indelible ink,



the factory refrigerant charge of the product,



the additional refrigerant amount charged in the field and



1 + 2

the total refrigerant charge

on the refrigerant charge label supplied with the product.

Important information regarding the refrigerant used

This product contains fluorinated greenhouse gases covered by the Kyoto Protocol.

Do not vent gases into the atmosphere.

1 factory refrigerant charge of the product: see unit name plate

2 additional refrigerant amount charged in the field

(Refer to the above information for the quantity of refrigerant

replenishment.)

3 total refrigerant charge

4 Contains fluorinated greenhouse gases covered by the Kyoto Protocol

5 outdoor unit

6 refrigerant cylinder and manifold for charging

The filled out label must be adhered in the proximity of the product charging port (e.g. onto the inside of the stop valve

cover).

R32

Refrigerant type: R32

GWP

(1)

value: 675

(1)

GWP = global warming potential

Downloaded from www.Manualslib.com manuals search engine

English 10

Refrigerant Piping Work

6. Refrigerant piping work

Cautions on pipe handling

1) Protect the open end of the pipe against dust and moisture.

2) All pipe bends should be as gentle as possible. Use a pipe bender for

bending.

Selection of copper and heat insulation materials

When using commercial copper pipes and fittings, observe the following:

1) Insulation material: Polyethylene foam

Heat transfer rate: 0.041 to 0.052W/mK (0.035 to 0.045kcal/mh°C)

Refrigerant gas pipe’s surface temperature reaches 110°C max.

Choose heat insulation materials that will withstand this temperature.

2) Be sure to insulate both the gas and liquid piping and to provide insulation dimen-

sions as below.

3) Use separate thermal insulation pipes for gas and liquid refrigerant pipes.

4) Piping and other pressure containing parts shall comply with the applicable legislation and shall be suitable for refrigerant.

Use phosphoric acid deoxidised seamless copper for refrigerant.

7. Flaring the pipe end

1) Cut the pipe end with a pipe cutter.

2) Remove burrs with the cut surface facing down-

ward so that the chips do not enter the pipe.

3) Put the flare nut on the pipe.

4) Flare the pipe.

5) Check that the flaring is properly made.

WARNING

• Do not use mineral oil on flared part.

• Prevent mineral oil from getting into the system as this would reduce the lifetime of the units.

• Never use piping which has been used for previous installations. Only use parts which are delivered with the unit.

• Never install a dryer to this R32 unit in order to guarantee its lifetime.

• The drying material may dissolve and damage the system.

• Incomplete flaring may cause refrigerant gas leakage.

Gas pipe

O.D.: 9.5mm, 12.7mm / Thickness: 0.8mm (C1220T-O)

O.D.: 15.9mm / Thickness: 1.0mm (C1220T-O)

Liquid pipe O.D.: 6.4mm / Thickness: 0.8mm (C1220T-O)

Gas pipe insulation I.D.: 12-15mm, I.D.: 16-20mm / Thickness: 13mm min.

Liquid pipe insulation I.D.: 8-10mm / Thickness: 10mm min.

Minimum bend radius

O.D.: 6.4mm, 9.5mm / 30mm or more

O.D.: 12.7mm / 40mm or more

O.D.: 15.9mm / 50mm or more

Wall

If no flare cap is

available, cover

the flare mouth

with tape to keep

dirt or water out.

Be sure to

place a cap.

Rain

Gas pipe

Liquid pipe

Gas pipe

insulation

Liquid pipe

insulation

Finishing tape

Drain hose

Inter-unit wires

(Cut exactly at

right angles.) Remove burrs

Set exactly at the position shown below.

Flaring

Die

Check

Flare’s inner

surface must

be flaw-free.

The pipe end must

be evenly flared in

a perfect circle.

Make sure that the

flare nut is fitted.

A 0-0.5mm

Clutch-type

Flare tool for R32

1.0-1.5mm

Clutch-type (Rigid-type)

1.5-2.0mm

Wing-nut type (Imperial-type)

Conventional flare tool

Downloaded from www.Manualslib.com manuals search engine

11 English

How to Use Reducers

Use the reducers supplied with the unit as described below.

1) Connecting a pipe of φ12.7 to a gas pipe connection port for φ15.9:

2) Connecting a pipe of φ9.5 to a gas pipe connection port for φ15.9:

3) Connecting a pipe of φ9.5 to a gas pipe connection port for φ12.7:

• When using the reducer packing shown above, be careful not to over-

tighten the nut, or the smaller pipe may be damaged. (about 2/3 - 1

the normal torque)

• Apply a coat of refrigeration oil to the threaded connection port of the

outdoor unit where the flare nut comes in.

• Use an appropriate wrench to avoid damaging the connection thread

by overtightening the flare nut.

Flare nut tightening torque

Flare nut for φ9.5

32.7–39.9N·m

(333–407kgf·cm)

Flare nut for φ12.7

49.5–60.3N·m

(505–615kgf·cm)

Flare nut for φ15.9

61.8–75.4N·m

(630–769kgf·cm)

No.1

φ15.9

→ φ12.7

No.2

φ12.7

→ φ9.5

No.3

φ15.9

→ φ12.7

No.4

φ12.7

→ φ9.5

No.5

φ15.9

→ φ9.5

No.6

φ15.9

→ φ9.5

Gasket (1) Gasket (2) Reduce and gasket

No. 1

No. 3

Flare nut (for φ15.9)

Inter-unit piping

Connection port

of outdoor unit

Be sure to attach

the gasket.

No. 5

No. 6

Flare nut (for φ9.5)

Be sure to attach

the gasket.

No. 4

No. 2

Flare nut (for φ12.7)

Be sure to attach

the gasket.

Downloaded from www.Manualslib.com manuals search engine

English 12

Pump Down Operation

In order to protect the environment, be sure to pump down when relocating or disposing of the unit.

1) Remove the valve cap from liquid stop valve and gas stop valve.

2) Carry out forced cooling operation.

3) After 5 to 10 minutes, close the liquid stop valve with a hexagonal

wrench.

4) After 2 to 3 minutes, close the gas stop valve and stop forced cool-

ing operation.

1. Forced operation

1) Switch off the power.

2) Remove the Service lid (2 screws).

3) Remove the service PC-board switch cover (1 screw).

4) Switch SW5 and SW6 to off.

5) Turn the operation mode switch (SW2) to COOL.

6) Screw the service PC-board switch cover back on (1 screw)-

7) Switch the power on.

8) Push the forced operation switch (SW1) above the service PC-board cover.

■Start forced colling operation.

To stop forced operation, push the forced operation switch (SW1) again.

WARNING

Do not remove the switch cover unless the power has been turned off. (Risk of electric shock)

Gas stop valve

Hexagonal

wrench

Liquid stop valve

Valve caps

Service PC-board

HEAT

COOL

S501

SW3

SW1

S502

Downloaded from www.Manualslib.com manuals search engine

13 English

Wiring

WARNING

• Do not use tapped wires, stranded wires, extension cords, or starburst connections, as they may cause overheating, electrical

shock, or fire.

• Do not use locally purchased electrical parts inside the product. (Do not branch the power for the drain pump, etc., from the ter-

minal block.) Doing so may cause electric shock or fire.

• Be sure to install an earth leakage breaker. (One that can handle higher harmonics.)

(This unit uses an inverter, which means that an earth leakage breaker capable of handling harmonics must be used, in order

to prevent malfunctioning of the earth leakage breaker itself.)

• Use an all-pole disconnection type breaker with at least 3mm between the contact point gaps.

• Do not connect the power wire to the indoor unit. Doing so may cause electric shock or fire.

1) Strip the insulation from the wire (3/4inch (20mm)).

2) Connect the connection wires between the indoor

and outdoor units so that the terminal numbers

match. Tighten the terminal screws securely. We

recommend a flathead screwdriver be used to

tighten the screws.

3) Be sure to match the symbols for wiring and

piping.

4) Pull the wire lightly to make sure that it does not

disconnect.

5) Pass the wiring through the cutout on the bottom of

the protection plate and attach the protection plate.

6) After completing the work, reattach the service lid to its original position.

Room

Safety breaker

Earth leakage

circuit breaker

Outdoor unit

50Hz

220-240V

Be sure to use the dedicated circuits.

To room B

To room E

To room C

To room D

Room

Room A

Room

Indoor unit

Power supply wire

3-core 2.5mm² or more

H05RN

Inter-unit wire

4-core 1.5mm² or more

H05RN

Room A

Room

Room D

Room B

power supply

Room E

Shape the wires so that there is

no lifting of the service hatch or

other structural parts.

8VHWKHVSHFL¿HGZLUHVDQG

connect them securely.

Equipment complying

with EN/IEC 61000-3-12

EDVHGRQFXUUHQW

measurement)

Downloaded from www.Manualslib.com manuals search engine

English 14

Wiring

CAUTION

Ground

This air conditioner must be grounded. For grounding, follow all local, and state electrical codes.

Standby Electricity Saving

The standby electricity saving function turns off power supply to the outdoor unit and sets the indoor unit into

standby electricity saving mode, thus reducing the power consumption of the air conditioner.

The standby electricity saving function works on the following indoor unit.

CAUTION

• The standby electricity saving function cannot be used for models other than the specified ones.

• Procedure for turning on standby electricity saving

function

1) Check that the main power supply is turned off. Turn it

off if it has not been turned off.

2) Remove the stop valve cover.

3) Disconnect the selective connector for standby

electricity saving.

4) Turn on the main power supply.

CAUTION

• Before connecting or disconnecting the selective connector for standby electricity saving, make sure that the main power

supply is turned off.

• The selective connector for standby electricity saving is required if an indoor unit other than the above applicable one is connected.

Good

Round crimp-

style terminal

Flat washer

Screw

Wrong

Flat washer

Round crimp-

style terminal

Screw

Flat washer

Screw

Round

crimp-style

terminal

Arrow view

Stranded

wire

Round crimp-style

terminal

• Precautions to be taken for power supply wiring. When using

stranded wires, make sure to use the round crimp-style terminal

for connection to the power supply terminal

Strip wire end

to this point.

Excessive strip length

may cause electric shock

or current leakage.

Stripping wire at terminal block

Good Wrong

• When connecting the inter-unit wires to the terminal block using a single core wire,

be sure to curl the end of the lead. Improper work may cause heat and fires.

1-3

A<B

• Make sure that the

earth wire between

the pull relief and

terminal is longer

than the other

wires.

3MXM40M, 3MXM52M, 3AMX52M only

For FTXM, FTXP, FTXJ type

Standby electricity saving

function off.

Standby electricity saving

function on.

The standby electricity saving function is turned off before shipping.

Downloaded from www.Manualslib.com manuals search engine

15 English

Priority Room Setting

• To use priority room setting, initial settings must be made when the unit is installed. Explain the priority room setting, as described

below, to the customer, and confirm whether or not the customer wants to use priority room setting.

Setting it in the guest and living rooms is convenient.

1. About the priority room setting function

The indoor unit for which priority room setting is applied takes priority in the following cases.

1-1.

Operation mode priority

The operation mode of the indoor unit which is set for priority room setting takes priority. If the set indoor unit is operat-

ing, all other indoor units do not operate and enter standby mode, according to the operation mode of the set indoor

unit.

1-2.

Priority during high-power operation

If the indoor unit which is set for priority room setting is operating at high power, the capabilities of other indoor units will

be somewhat reduced. Power supply gives priority to the indoor unit which is set for priority room setting.

1-3.

Quiet operation priority

Setting the indoor unit to quiet operation will make the outdoor unit run quietly.

Setting procedure

Slide the switch to the ON side for the switch that corresponds to the piping connected to the indoor unit to be set. (In the fig-

ure below, it is room A.) Once the settings are complete, reset the power.

Be sure to only set one room

Service PC-board

HEAT

COOL

Screw

Remove

the switch

cover

ON OFF

Priority room setting switch (SW4)

Downloaded from www.Manualslib.com manuals search engine

English 16

Night Quiet Mode Setting

• If Night Quiet Mode is to be used, initial settings must be made when the unit is installed. Explain Night Quiet Mode, as

described below, to the customer, and confirm whether or not the customer wants to use Night Quiet Mode.

About Night Quiet Mode

The Night Quiet Mode function reduces operating noise of the outdoor unit at nighttime. This function is useful if the customer

is worried about the effects of the operating noise on the neighbors.

However, if Night Quiet Mode is running, cooling

capacity will be saved.

Setting procedure

Turn the Night Quiet Mode switch (SW6-1) to on.

HEAT Mode Lock

<SW5-1>

• Use the HEAT Mode Lock switch (SW5-1) in the

“ON” position.

COOL Mode Lock <S15>

• Use the S15 connector to set the unit to cool only.

Setting to only cool (C) : short-circuit pins 3 and 5 of the connector <S15>

The following specifications apply to the connector housing and pins.

ST products Housing: VHR-5N

Pin: SVH-21T-1,1

Note that forced operation is also possible in COOL mode.

Service PC-board

Heat Mode Lock (SW5-1)

(SW6-1)

ON OFF

COOL

Screw

Night Quiet Mode

setting switch

Remove

the switch

cover

COOL mode (C)

13 5

Downloaded from www.Manualslib.com manuals search engine

17 English

Trial Operation and Testing

• Before starting the test run, measure the voltage at the primary side of the safety breaker.

• Check that all liquid and gas stop valves are fully open.

• Check that piping and wiring all match. The wiring error check can be conveniently used for underground wiring and other wiring

that cannot be directly checked.

1. Wiring error check

• This product is capable of automatic correction of wiring error.

• Press the “wiring error check switch” on the outdoor unit service PC-

board. However, the wiring error check switch will not function for 3 min-

utes after the safety breaker is turned on, or depending on the outside

air conditions (See Note 2.). About 15–20 minutes after the switch is

pressed, the errors in the connection wiring will be corrected.

If self-correction is not possible, check the indoor unit wiring and piping

in the usual manner.

NOTE:

1) For two rooms, LED 3, 4 and 5 are not displayed, and for three rooms, LED 4 and 5 is not displayed, and for four rooms,

LED 5 is not displayed.

2) If the outside air temperature is 5°C or less , the wiring error check function will not operate.

3) After wiring error check operation is completed, LED indication will continue until ordinary operation starts.

This is normal.

4) Follow the product diagnosis procedures. (Details of product error diagnosis are listed on the back of the right side

plate.)

Service PC-board

Wiring error

check switch

(SW3)

The service monitor LEDs indicate whether or not correction is

possible, as shown in the table below. For details about how to read the

LED display, refer to the service manual.

Terminal block

Wiring error check

LED lighting sequence after a wiring correction.

Order of LED flashing: 2 ➝ 1 ➝ 3 ➝ 4

From Room C

to the “kitchen”

From Room B

to the “living room”

From Room D

to the “children’s room”

From Room A

to the “bedroom”

Wiring correct example

∗ The figure at left shows branch wiring.

LED

Status

1 2 3 45

All Flashing

Automatic correction impossible

Automatic correction completed

Abnormal stop [NOTE. 4]

Message

Flashing One after another

(One or more of LEDs 1 to 4 are ON)

Downloaded from www.Manualslib.com manuals search engine

Pagina se încarcă ...

Daikin 3MXM40N Manualul proprietarului

Marca: Daikin

Model: 3MXM40N

Categorie: Aparate de aer condiționat cu sistem divizat

Tip: Manualul proprietarului

Descărcați PDF

raport

în alte limbi

English: Daikin 3MXM40N Owner's manual

Daikin 3MXM40N Manualul proprietarului

Daikin 3MXM40N Manualul proprietarului

în alte limbi

Lucrări conexe

Alte documente