Tesla TC53P4-1832IA Manual de utilizare

SPLIT-TYPE

AIR CONDITIONER

USER MANUAL

For R32 DC Inverter models:

TC26P4-0932IA

TC35P4-1232IA

TC35P4-1232IAW

TC53P4-1832IA

MKD

BIH/

MNE

RO SLO SRBENG BG GR HR

Ver. 2021

OPERATING INSTRUCTION

Note: All the pictures in this manual are just schematic diagrams, the actual is the standard. Please read

this owner’s manual carefully and thoroughly before operating the unit! Take care of this manual for future

reference.

UPUTE ZA UPOTREBU

Napomena: Sve slike u ovom priručniku su samo shematski dijagrami, ﬁzički proizvod je standard. Molimo

Vas da pažljivo i temeljito pročitate ovo uputstvo za upotrebu prije korištenja uređaja! Čuvajte ovaj priručnik

za buduće korištenje.

ΕΓΧΕΙΡΙΔΙΟ ΧΡΉΣΉΣ

Σημείωση: Οι εικόνες στο παρόν εγχειρίδιο είναι σχεδιαγράμματα, ανατρέξτε στο πραγματικό προϊόν. Διαβάστε

προσεκτικά τις προφυλάξεις στο παρόν εγχειρίδιο προτού θέσετε τη μονάδα σε λειτουργία! Φυλάξτε το παρόν

εγχειρίδιο για μελλοντική χρήση.

ИНСТРУКЦИЯ ЗА УПОТРЕБА

Забележка: Всички снимки в тази инструкция са само схематични диаграми, действителните са

стандартните. Моля, прочетете внимателно тази инструкция за употреба преди да започнете работа с

уреда! Запазете тази инструкция за бъдещи справки

UPUTSTVO ZA UPOTREBU

Napomena: Sve slike u ovom priručniku su samo šematski dijagrami, ﬁzički proizvod je standard. Molimo Vas

da pažljivo i temeljno pročitate ovo uputstvo za upotrebu prije korišćenja uređaja! Sačuvajte ovo uputstvo za

buduću upotrebu.

PRIROČNIK ZA UPORABO

Opomba: Vse slike v tem priročniku so le shematske risbe, dejansko stanje je standard. Prosimo, da pred

uporabo skrbno in temeljito preberete ta priročnik za uporabo! Priročnik shranite za kasnejšo uporabo.

MANUAL DE UTILIZARE

Nota: Fotograﬁile din acest manual sunt doar diagrame schematice. Vă rugăm să citiți “Manualul de Utilizare”

cu atenție, înainte de a utiliza aerul condiționat, pentru a asigura funcționarea corespunzătoare. Păstrați

manualul pentru referințe ulterioare.

ENG

HR

GR

BG

BIH/

MNE

SLO

RO

УПАТСТВО ЗА УПОТРЕБА

Напомена: Сите слики во овој прирачник се само шематски дијаграми, физичкиот производ е

стандард. Ве молиме внимателно и теменлно да го причитате ова упатство за употреба пред

користење на уредот! Сочувајте го ова упатство за идна употреба.

MKD

UPUTSTVO ZA UPOTREBU

Napomena: Sve slike u ovom priručniku su samo šematski dijagrami, ﬁzički proizvod je standard. Molimo

Vas da pažljivo i temeljno pročitate ovo uputstvo za upotrebu pre korišćenja uređaja! Sačuvajte ovo

uputstvo za buduću upotrebu.

SRB

3

ENG

Warning: This air conditioner uses R32 ﬂammable refrigerant.

• The room space for the installation, use, repair, and storage of this air conditioner should be greater than 5 m’.

• Air conditioner refrigerant can not charge more than 1. 7kg.

• Do not use any methods to speed up defrost or to clean frosty parts except for particular recommended by

manufacturer.

• Not pierce or burn air conditioner, and check the refrigerant pipeline wether be damaged.

• The air conditioner should be stored in a room without lasting ﬁre source, for example, open ﬂame, burning gas

appliance, working electric heater and so on.

• Notice that the refrigerant may be tasteless.

• The storage of air conditioner should be able to prevent mechanical damage caused by accident.

• Maintenance or repair of air conditioners using R32 refrigerant must be carried out after security check to

minimize risk of incidents.

• Air conditioner must be installed with stop valve cover.

• Please read the instruction carefully before installing, using and maintaining.

Notes: Air conditioner with R32 refrigerant, if roughly treated, may cause serious harm to the human body

or surrounding things.

Incorrect installation or operation by not following these instructions may cause harm or damage to

people, properties, etc. The seriousness is classiﬁed by the following indications:

This symbol indicates the possibility of death or serious injury.

This symbol indicates the possibility of injury or damage to properties.

Symbol Note Explanation

WARNING

This symbol shows that this appliance uses a ﬂammable refrigerant.If

the refrigerant is leaked and exposed to an external ignition source,

there is a risk of ﬁre.

CAUTION

This symbol shows that the operation manual should be read

carefully.

CAUTION

This symbol shows that a service personnel should be handling this

equipment with reference to the installation manual.

CAUTION

This symbol shows that information is available such as the operating

manual or installation manual.

WARNING

SAFETY PRECAUTIONS

WARNING!

CAUTION!

4

ENG

WARNING!

• This appliance can be used by children aged from 8 years and above and persons with reduced physical,

sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or

instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall

not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

(Only for the AC with CE-MARKING)

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction

concerning use of the appliance by a person responsible for their safety. Children should be supervised to

ensure that they do not play with the appliance. (Except for the AC with CE-MARKING)

•

The air conditioner must be grounded. Incomplete grounding may result in electric shocks. Do

not connect the earth wire to the gas pipeline, water pipeline, lightning rod, or telephone earth wire.

• Always switch off the device and cut the power supply when the unit is not in use for long time so as to ensure

safety.

• Take care not let the remote control and the indoor unit watered or being too wet. Otherwise, it may cause short

circuit.

• If the power supply cable is damaged, it must be replaced by manufacture or its service agent or a similar

qualiﬁed person.

• Don’t cut off main power switch during operating or with wet hands. It may cause electric shock.

• Don’t share the socket with other electric appliance. Otherwise, it may cause electric shock even ﬁre and

explosion.

• Always switch off the device and cut the power supply before performing any maintenance or cleaning.

Otherwise, it may cause electric shock or damage.

• Don’t pull the power cord when pull out the power plug. The damage of pulling power cord will cause serious

electric shock.

• A warning that ducts connected to an appliance shall not contain an ignition source.

• Don’t install air conditioner in a place where there is ﬂammable gas or liquid. The distance between them

should above 1m. It may cause ﬁre even explosion.

• Don’t use liquid or corrosive cleaning agent wipe the air conditioner and sprinkle water or other liquid either.

Doing this may cause electric shock or damage to the unit.

• Don’t attempt to repair the air conditioner by yourself. Incorrect repairs may cause ﬁre or explosion. Contact a

qualiﬁed service technician for all service requirement.

• Don’t use air conditioner in lightning strom weather. Power supply should be cut in time to prevent the

occurrence of danger.

• Don’t put hands or any objects into the air inlets or outlets. This may cause personal injury or damage to the unit.

• Please note whether the installed stand is ﬁrm enough or not. If it is damaged, it may lead to the fall of the unit

and cause the injury.

• Don’t block air inlet or air outlet. Otherwise, the cooling or heating capacity will be weakened, even cause

system stop operating.

• Don’t let the air conditioner blow against the heater appliance. Otherwise it will lead to incomplete combustion,

thus causing poisoning.

• The appliance shall be installed in accordance with national wiring regulations.

• An earth leakage breaker with rated capacity must be installed to avoid possible electric shocks.

• This product contains ﬂuorinated greenhouse gases.

• Refrigerant leakage contributes to climate change.

Refrigerant with lower global warming potential (GWP) would contribute less to global warming than a

refrigerant with higher GWP, if leaked to the atmosphere. This appliance contains a refrigerant ﬂuid with a GWP

equal to [675]. This means that if 1 kg of this refrigerant ﬂuid would be leaked to the atmosphere, the impact on

global warming would be [675] times higher than 1 kg of CO2, over a period of 100 years. Never try to interfere

with the refrigerant circuit yourself or disassemble the product yourself and always ask a professional.

• Ensure no following objects under the indoor unit:

1. microwaves, ovens and other hot objects.

2. computers and other high electrostatic appliances.

3. sockets that plug frequently.

• The joints between indoor and outdoor unit shall not be reused, unless after re-ﬂaring the pipe.

• The speciﬁcation of the fuse are printed on the circuit bord, such as: 3.15A/250V AC, etc.

5

ENG

• Don’t open the windows and doors for long time when the air conditioner is running. Otherwise, the cooling or

heating capacity will be weakened.

• Don’t stand on the top of the outdoor unit or place heavy things on it. This cloud cause personal injuries or

damage the unit.

• Don’t use the air conditioner for other purposes, such as drying clothes, preserving foods,etc.

• Don’t apply the cold air to the body for a long time. It will deteriorate your physical conditions and cause health

problems.

• Set the suitable temperature. It is recommended that the temperature difference between indoor and outdoor

temperature should not be too large. Appropriate adjustments of the setting temperature can prevent the

waste of electricity.

• If your air conditioner is not ﬁtted with a supply cord and a plug, an anti-explosion all-pole switch must be

installed in the ﬁxed wiring and the distance between contacts should be no less than 3.0 mm.

• If your air conditioner is permanently connected to the ﬁxed wiring, a anti-explosion residual current device

(RCD) having rated residual operating current not exceeding 30 mA should be installed in the ﬁxed wiring.

• The power supply circuit should have leakage protector and air switch of which the capacity should be more

than1 .5 times of the maximum current.

• Regarding the installation of the air conditioners, please refer to the below paragraphs in this manual.

• Within the temperature range provided in following table, the air conditioner may stop running and other

anomalies may arise.

• When the temperature is too high, the air conditioner may activate the automatic protection device, so that the

air conditioner could be shut down.

• When the temperature is too low, the heat exchanger of the air conditioner may freeze, leading to water

dripping or other malfunction.

• In long-term cooling or dehumidiﬁcation with a relative humidity of above 80% (doors and windows are open),

there may be water condenses or dripping near the air outlet.

• T1 and T3 refer to ISO 5151.

WEEE Warning

Meaning of crossed out wheeled dustbin: Do not dispose of electrical appliances as

unsorted municipal waste, use separate collection facilities. Contact you local government for

information regarding the collection systems available. If electrical appliances are disposed

of in landﬁlls or dumps, hazardous substances can leak into the groundwater and get into the

food chain, damaging yourhealth and well-being. When replacing old appliances with new

ones, the retailer is legally obligated to take back your old appliance for disposals at least free

of charge.

CAUTION!

NOTICES FOR USE

The conditions of unit can’t normally run

Cooling

Outdoor

>43°C (Apply to T1)

>52°C (Apply to T3)

Indoor <18°C

Heating

Outdoor

>24°C

<-7°C

Indoor >27°C

6

ENG

Notes for heating

Notes for turning off

Emergency operation

Airﬂow direction adjustment

Speciﬁc caution

• The fan of the indoor unit will not start running immediately after the heating is started to avoid blowing out cool

air.

• When it is cold and wet outside, the outdoor unit will develop frost over the heat exchanger which will increased

the heating capacity. Then the air conditioner will start defrost function.

• During defrost, the air conditioner will stop heating for about 5-12 minutes.

• Vapor may come out from the outdoor unit during defrost. This is not a malfunction, but a result of fast defrost.

• Heating will resume after defrost is complete.

• When the air conditioner is turned off, the main controller will automatically decide whether to stop immediately

or after running for dozens of seconds with lower frequency and lower air speed.

• If the remote controller is lost or broken, use force switch

button to operate the air conditioner.

• If this button is pushed with the unit OFF, the air

conditioner will operate in Auto mode.

• If this button is pushed with the unit ON, the air

conditioner will stop running.

1. Use up-down swing and left-right swing buttons on the remote

controller to adjust the airﬂow direction. Refer to the operation

manual of the remote controller for detail.

2. For models without left-right swing function, the ﬁns has to be

moved manually.

Note: Move the ﬁns before the unit is in operation, or your ﬁnger

might be injured. Never place your hand into the air inlet or outlet

when the air conditioner is in operation.

1.Open front panel of the indoor.

2. The connector (as Fig) can not touch the terminal

board, and is positioned as shown in Fig.

Force switch

Connector

Cable 1

Cable 2

Terminal board

7

ENG

NAMES OF EACH PART

Indoor unit

Outdoor unit

Air inlet grille

Panel

Air ﬁlter

Air louver

Remote controller

Pipe

protection

ring

Force switch

Air inlet

Air outlet

Air vent

Power cable

Air outlet grille

Air outlet

Connecting

pipe

Drain hose

Note: All the pictures in this manual are just schematic diagrams, the actual is the standard.

Plug, WiFi function, Negative-ion function, and vertical and horizontal; swing function both are optional.

8

ENG

WARNING!

• Before the cleaning of the air conditioner, it must be shut down and the electricity must be cut off for more than

5 minutes, otherwise there might be the risk of electric shocks.

• Do not wet the air conditioner, which can cause an electric shock. Make sure not to rinse the air conditioner with

water under any circumstances.

• Volatile liquids such as thinner or gasoline will damage the air conditioner housing, therefore please clean the

housing of air conditioner only with soft dry cloth and damp cloth moistened with neutral detergent.

• In the course of the using, pay attention to cleaning the ﬁlter regularly, to prevent the covering of dust which

may affect the effect. If the service environment of the air conditioner is dusty, correspondingly increase the

number of times of cleaning. After removing the ﬁlter, do not touch the ﬁn part of the indoor unit with the ﬁnger,

and no force to damage the refrigerant pipeline.

Clean the panel

Clean the air ﬁlter

Check before use

Remove the air ﬁlter

Clean the Air Filter

Mount the Filter

When the panel of the indoor unit is contaminated, clean it gently with a wrung towel using tepid water below

40°C, and do not remove the panel while cleaning.

1. Use both hands to open the panel for an angle from both ends of the panel in accordance with the direction of

the arrow.

2. Release the air ﬁlter from the slot and remove it.

Use a vacuum cleaner or water to rinse ﬁlter, and if the ﬁlter is very dirty (for example, with greasy dirt),

clean it with warm water (below 45 °C) with mild detergent dissolved in, and then put the ﬁlter in

the shade to dry in the air.

1. Check whether all the air inlets and outlets of the units are unblocked.

2. Ceck whether there is blocking in the water outlet of the drain pipe, and immediately clean it up if any.

3. Check the ground wire is reliably grounded.

4. Check whether the remote control batteries are installed, and whether the power is sufﬁcient.

5. Check whether there is damage in the mounting bracket of the outdoor unit, and if any, please contact our local

service center.

1. Reinstall the dried ﬁlter in reverse order of removal, then cover and lock the panel.

CLEAN AND CARE

9

ENG

Maintain after use

TROUBLESHOOTING

1. Cut off the power source of the air conditioner, turn off the main power switch and remove the batteries from the

remote controller.

2. Clean the ﬁlter and the unit body.

3. Remove the dust and debris from the outdoor unit.

4. Check whether there is damage in the mounting bracket of the outdoor unit, and if any, please contact our local

service center.

Do not repair the air conditioner by yourself as wrong maintenance may cause electric shock or ﬁre or explode,

please contact the authorized service center and let the professionals conduct the maintenance, and checking the

following items prior to contacting for maintenance can save your time and money.

CAUTION!

Phenomenon Troubleshooting

The air conditioner does

not work.

• There might be power outages. → Wait until power is restored.

• Power plug may be loose out from the socket. → The plug in the plug tightly.

• Power switch fuse may blow. → Replace the fuse.

• The time for timing boot is yet to come. → Wait or cancel the timer settings.

The air conditioner can’t

run after the immediate

start-up after it is shut

down.

• If the air conditioner is turned on immediately after it is turned off, the protective

delay switch will delay the operation for 3 to 5 minutes.

The air conditioner stops

running after it starts up

for a while.

• May reach the setting temperature. → It is a normal function phenomenon.

• May be at a defrosting state. → It will automatically restore and run again after

defrosting.

• Shutdown Timer may be set. → If you continue to use, please turn it on again.

The wind blows out, but

the cooling/ heating

effect is not good.

• Excessive accumulation of dust on ﬁlter, blocking at air inlet and outlet, and the

excessively small angle of the louver blades all will affect the cooling and heating

effect. → Please clean the ﬁlter, remove the obstacles at the air inlet and outlet

and regulate the angle of the louver blades.

• Poor cooling and heating effect caused by doors and windows opening, and

unclosed exhaust fan. → Please close the doors, windows, the exhaust fan, etc.

• Auxiliary heating function is not turned on while heating, which may lead to poor

heating effect. → Turn on the auxiliary heating function. (only for models with

auxiliary heating function)

• Mode setting is incorrect, and the temperature and wind speed settings are not

appropriate. → Please re-select the mode, and set the appropriate temperature

and wind speed.

The indoor unit blows

out odor.

• The air conditioner itself does not have undesirable odor. If there is odor, it may

be due to accumulation of the odor in the environment. → Clean the air ﬁlter or

activate the cleaning function.

There is sound of

running water during

the running of air

conditioner.

• When the air conditioner is started up or stopped, or the compressor is started

up or stopped during the running, sometimes the “hissing” sound of running

water can be heard. → This is the sound of the ﬂow of the refrigerant, not a

malfunction.

10

ENG

Phenomenon Troubleshooting

A slight “click” sound is

heard at the of start-up

or shut-down.

• Due to temperature changes, panel and other parts will swell, causing the sound

of friction. → This is normal, not a fault.

The indoor unit makes

abnormal sound.

• The sound of fan or compressor relay switched on or off.

• When the defrosting is started or stop running, it will sound. → That is due to the

refrigerant ﬂowed to reverse direction. They are not malfunctions.

• Too much dust accumulation in the air ﬁlter of the indoor unit may result in

ﬂuctuation of the sound. → Clean the air ﬁlters in time.

• Too much air noise when “Strong wind” is turned on. → This is normal, if feeling

uncomfortable, please deactivate the “Strong wind” function.

There are water drops

over the surface of the

indoor unit.

• When ambient humidity is high, water drops will be accumulated around the air

outlet or the panel, etc. → This is a normal physics phenomenon.

• Prolonged cooling run in open space produces water drops. → Close the doors

and windows.

• Too small opening angle of the louver blades may also result in water drops at

the air inlet. → Increase the angle of the louver blades.

During the cooling

operation, the indoor

unit outlet sometimes

will blow out mist.

• When the indoor temperature and humidity are high, it happens sometimes.

→ This is because the indoor air is cooled rapidly. After it runs for some time, the

indoor temperature and humidity will be reduced and the mist will disappear.

Immediately stop all operations and cut off the power supply, contact our Service center locally in

following situations.

• Hear any harsh sound or smell any awful odor during running.

• Abnormal heating of power cord and plug occurs.

• The unit or remote controller has any impurity or water.

• Air switch or leakage protection switch is often disconnected.

IMPORTANT NOTICES!

NOTICES FOR INSTALLATION

Unpacking Inspection

• Before installating, please contact with local authorized maintenance cenler, if unit is not installed by the

authorized maintenance center, the malfunction may not solved,due to discommodious contact.

• The air conditioner must be installed by professionals according to the national wiring rules and this manual.

• Refrigerant leak tesf must be made after installation.

• To move and install air conditioner to another place, please contact our local special service center.

• Open the box and check air conditioner in area with good ventilation (open the door and window) and without

ignition source.

Note: Operators are required to wear anti-static devices.

• It is necessary to check by professional whether there is refrigerant leakage before opening tlie box of outdoor

machine; stop installing the air conditioner if leakage is found.

• The ﬁre prevention equipment and anti-static precautions shall be prepared well before checking.Then check

the refrigerant pipeline to see if there is any collision traces, and whether the outlook 1s good.

11

ENG

Safety Principles for Installing Air Conditioner

Requirements For Installation Position

• Fire prevention device shall be prepared before installation.

• Keep installing site ventilated.(open the door and window)

• Ignition source,smoking and calling is not allowed to exist in area where R32 refrigerant rocated.

• Anti-static precautions in necessary for installing air conditioner, e.g. wear pure cotton clothes and gloves.

• Keep leak detector in working state during the installation.

• If R32 refrigerant leakage occurs during tﬂe installation, you shall immediately detect the concentration in indoor

environment until it reaches a safe level. If refrigerant leakage affects the performance of the air conditioner,

please immediately stop the operation, and the air conditioner must be vacuumed ﬁrstly and be returned to the

maintenance station for processing.

• Keep electric appliance, power switch, plug, socket, high temperature heat source and high static away from the

area underneath sidelines of the indoor unit.

• The air conditioner shall be installed in an accessible location to installation and maintenance, without obstacles

that may block air inlets or outlets of indoor/outdoor units, and shall keep away from heat source inﬂammable or

explosive conditions.

• When installing or repairing the air conditioner and the connecting line is not long enough, the entire

connecting line shall be replaced with the connecting line of the original speciﬁcation; extension is not allowed.

• Use new connection pipe, unless re-ﬂaring the pipe.

• Avoid places of inﬂammable or explosive gas leakage or where there are strongly aggressive gases.

• Avoid places subject to strong artiﬁcial electric/magnetic ﬁelds.

• Avoid places subject to noise and resonance.

• Avoid severe natural conditions (e.g. heavy lampblack, strong sandy wind, direct sunshine or h1gli temperature

heat sources).

• Avoid places within the reach of cnildren.

• Shorten the connection between the indoor and outdoor units.

• Select where it is easy to perform service and repair and where the ventilation good.

• The outdoor unit shalrnot be installed in any way that could occupy an aisle, stairway, exit, ﬁre escape, catwalk or

any other public area.

• The outdoor unit shall be installed as far as possible from the doors and windows of the neighbors as well as the

green plants.

Installation environment inspection

• Check nameRlate of outdoor unit to make sure whether the refrigerant is R32.

• Check the ﬂoor space of the room. The space shall not be less than usable space(sm2 ) in the speciﬁcation.The

outdoor unit shall be installed at a well-ventilated place.

• Check the surrounding environment of installation site: R32 shall not be installed in the enclosed reserved space

of a building.

• When using electric drill to make holes in the wall, check ﬁrst whether there is pre-buried pipeline for water,

electricity and gas.

• It is suggested to use the reserved hole in the roof of tﬂe walr

Requirements of the mounting structure

• The mounting rack must meet the relevant national or industrial standards in terms of strength with welding and

connection areas rustproofed.

• The mounting rack and its load carry surface shall be able to withstand 4 times or above the weight of the unit,

or 200kg, whichever is heavier.

• The mounting rack of the outdoor unit shall be fastened with expansion bolt.

• Ensure the secure installation regardless of what type of wall on which it is installed, to prevent potential

dropping that could hurt people.

12

ENG

Requirements for operations at raised height

Grounding Requirements

Electrical Safety Requirements

• When carrying out installation at 2m or higher above the base level, safety belts must be worn and ropes of

sufﬁcient strength be securely fasten to the outdoor unit, to prevent falling that could cause personal injury or

death as well as property loss.

• The air conditioner is the class I electrical appliance and must ensure a reliable grounding.

• Do not connect the grounding wire to a gas pipe, water pipe, lightning rod, telephone line, or a circuit poorly

grounded to the earth.

• The grounding wire is specially designed and shall not be used for other purpose, nor shall it be fastened with a

common tapping screw.

• Interconnection cord diameter should be recommended as per instruction manual ,and with type O terminal

that meet local standards (internal diameter of type O terminal needs to match the screw size of the unit, no

more than 4.2mm). After installation, check the screws whether have been ﬁxed effectively, and there is no risk

of loosening.

• Be sure to use the rated voltage and air conditioners dedicated circuit for the power supply, and the power cord

diameter must meet the national requirements.

• When the maximum current of air conditioner is ≥16A, it must use the air switch or leakage protection switch

equipped with protection devices.

• The operating range is 90%-110% of the local rated voltage. But insufﬁcient power supply malfunction, electrical

shock, or ﬁre. If the voltage instability, proposed to increase the voltage regulator.

• The minimum clearance between the air conditioner and the combustibles is 1.5 m.

• The interconnection cord connect the indoor and outdoor units. You must ﬁrst choose the right cable size

before preparing it for connection.

• Cable Types: Outdoor Power Cable: H07RN-F or H05RN-F;

Interconnection cord: H07RN-F or H05RN-F;

• Minimum Cross-Sectional Area of Power cable and interconnection cord.

• The size of the interconnection cord, power cable, fuse, and switch needed is determined by the maximum

current of the unit. The maximum current is indicated on the nameplate located on the side panel of the unit.

Refer to this nameplate to choose the right cable, fuse, or switch.

• Note: Core number of cable refer to the detailed wiring diagram adhered on the unit which you purchased.

Appliance

Amps (A)

AWG

10 18

13 16

18 14

25 12

30 10

40 8

Rated Current of

Appliance (A)

Nominal Cross-Sectional

Area (mm

2

)

>3 and ≤ 6 0.75

>6 and ≤10 1

>10 and ≤16 1.5

>10 and ≤16 2.5

>10 and ≤16 4

>10 and ≤16 6

North America Other regions

13

ENG

Others

Packing list

• The connection method of the air conditioner and the power cord and the interconnection method of each

independent element shall be subject to the wiring diagram afﬁxed to the machine.

• The model and rating value of the fuse shall be subject to the silkscreen on corresponding controller or fuse

sleeve.

Name Quantity Unit

Indoor Unit 1 Set

Remote Controller 1 PC

Batteries (7#) 2 PC

Owner’s manual 1 Set

Drain pipe 1 PC

Name Quantity Unit

Outdoor Unit 1 Set

Connecting pipe

(optional)

2 PC

Plastic Strap 1 ROLL

Pipe Protection Ring 1 PC

Luting (putty)

(optional)

1 PACKET

Packing list of the indoor unit Packing list of the outdoor unit

Note: All accessories s hall be subject to actual packaging material, and if there is any difference, please

understand.

INSTALL INDOOR UNIT

Dimension drawing of indoor unit installation

Space to the ceiling

Space to the ﬂoor

Space to the wallSpace to the wall

15cm above

20cm above20cm above

200-260cm

14

ENG

Mounting plate

Wall-through Hole

Route of Pipeline

1. The wall for installation of the indoor unit shall be hard and

ﬁrm, so as to prevent vibration.

2. Use the “+” type screw to fasten the peg board, horizontally

mount the peg board on the wall, and ensure the lateral

horizontal and longitudinal vertical.

3. Pull the peg board by hand after the installation, to conﬁrm

whether it is solid.

1. Make a hole with an electric hammer or a water drill at the

predetermined position on the wall for piping, which shall

slant outwardly by 5° -10° .

2. To protect the piping and the cables from being damaged

running through the wall, and from the rodents that may

inhabit in the hollow wall, a pipe protecting ring shall be

installed and sealed with putty.

Note: Usually, the wall hole is ɸ60mm~ɸ80mm. Avoid pre-

buried power wire and hard wall when making the hole.

1. Depending on the position of the unit, the piping may be routed sideway from the left or the right (Fig 1), or

vertically from the back (Fig 2) (depending on the pipe length of the indoor unit). In the case of sideway routing,

cut off the outlet cutting stock of the opposite side.

Pipe protection

ring

Connecting Pipe

Drain Hose and

Cables

Connecting Pipe

Drain Hose and

Cables

Outlet material preparation

Fig 2

Putty

Fig 1

15

ENG

Drain pipe connection

Wrap the Piping

1. Remove the ﬁxed part to pull out pipe of indoor machine from the case. Screw the hexagon nut in the left of the

joint to the end with your hand.

2. Connect the connecting pipe to the indoor unit:

Aim at the pipe center, tighten the Taper nut with ﬁngers, and then tighten the Taper nut with a torque wrench,

and the direction is shown in diagram on the right. The torque used is shown in the following table.

Note: Carefully check if there is any damage of joints before installation.

The joints shall not be reused, unless after re-ﬂaring the pipe.

1. Use the insulation sleeve to wrap the joint part the indoor

unit and the connection pipe, and then use insulating

material to pack and seal insulation pipe, to prevent

generation of condensate water on the joint part.

2. Connect the water outlet with drain pipes, and make the

connection pipe, cables, and the drain hose straight.

3. Use plastic cable ties to wrap the connecting pipes, cables

and drain hose. Run the pipe sloping downward.

The size of pipe (mm) Torque (Nm)

ɸ6 / ɸ6. 35 15 ~ 88

ɸ9 / ɸ9. 52 35 ~ 40

ɸ12 / ɸ12.7 45 ~ 60

ɸ15.88 73 ~ 78

ɸ19.05 75 ~ 80

Tightening torque table

Indoor unit pipe

Spanner Torgue wrench

Connecting Pipe

Drain Hose

and Cables

Plastic Strap

Taper nut

Connecting

pipe

Fixing the Indoor Unit

1. Hang the indoor unit on the peg board, and move the

unit from left to right to ensure that the hook is properly

positioned in the peg board.

2. Push toward the lower left side and the upper right side of

the unit toward the peg board, until the hook is embedded

in the slot and makes a “click” sound.

16

ENG

Wiring diagram

• If your air conditioner is provided with interconnection cord , the wiring of the indoor unit is connected in the

factory, there is no need of connection.

• If the interconnection cord is not provided, connection is needed in accordance with the

After installation, check:

1. The screws whether have been ﬁxed effectively, and there is no risk of loosening.

2. Connector of display board whether put in the right place and do not touch the terminal board.

3. Control box cover whether cover tightly.

If there is a connector,

connect it directly.

Constant speed

To Outdoor unit

Variable speed

Connector

NOTE:

• This manual usually includes the wiring mode for the different kind of A/C. We cannot exclude the possibility that

some special type of wiring diagrams are not included.

• The diagram are for reference only. If the entity is difference with this wiring diagram, please refer to the detailed

wiring diagram adhered on the unit which you purchased.

17

ENG

Connect the Outdoor Unit with Connecting Pipe:

Aim the counter-bore of the connecting pipe at the stop valve, and

tighten the Taper nut with ﬁngers. Then tighten the Taper nut with

a torque wrench. When prolonging the piping, extra amount of

refrigerant must be added so that the operation and performance of

the air conditioner will not be compromised.

Note: 1. This table is for reference only.

2. The joints shall not be reused, unless after re-ﬂaring the pipe.

3. After installation, check the stop valve cover whether be ﬁxed effectively.

INSTALL OUTDOOR UNIT GAS R32

Dimension drawing of outdoor unit installation

Install the connection pipe

Left

installation feet

Right

installation feet

Air inlet

Air outlet

Outdoor Dimensions (mm)

LxHxD

Mounting Dimensions

Distance A (mm) Distance B (mm)

735x475x250 453 280

790x520x280 508 314

848x670x354 544 354

Piping

length

Amount of refrigerant to be added

Amount of

refrigerant for

the unit

5M Not needed

5-15M

CC12000Btu 15g/m 1 kg

CC18000Btu 30g/m 2 kg

Connection

pipe

Liquid side pipe

Gas side pipe

Spanner

Stop valve

cover

Taper nutStop valve

18

ENG

1. Loosen the screws and remove E-parts cover from the unit.

2. Connect the cables respectively to the corresponding terminals of

the terminal board of the outdoor unit (see the wiring diagram), and if

there are signals connected to the plug, just conduct butt joint.

3. Ground wire: Remove the grounding screw out of the electric bracket,

cover the grounding wire end onto the grounding screw and screw it

into the grounding hole.

4.Fix the cable reliably with fasteners (Pressing board).

5. Put the E-parts cover back in its original place and fasten it with screws.

INSTALL OUTDOOR UNIT

Wiring Connection

Wiring diagram

Constant speed

Connector

If there is a connector, connect it directly.

Note:

• This manual usually includes the wiring mode for the different kind of A/C. We cannot exclude the possibility

that some speciaI type of wiring diagrams are not included.

• The diagram are for reference only. If the entity is difference with this wiring diagram, please refer to the detailed

wiring diagram adhered on the unit which you purchased.

Variable speed

To indoor unit

To power

E-parts cover

19

ENG

Vacuuming (Gas R32)

Exclusive R32 refrigerant pump must be used in making R32 refrigerant vacuum.

Before working on the air conditioner, remove the cover of

the stop valve(gas and liquid valves)and be sure to retighten it

afterward.(to prevent the potential air leakage).

1. To prevent air leakage and spilling tighten all connecting

nut of all ﬂare tubes.

2. Connect the stop valve, charge hose, manifold valve, and

vacuum pump.

3. Fully open the handle Lo of the manifold valve and

apply vacuum for at least 15 minutes and check that the

compound vacuum gauge reads -0.1MPa (-76cmHg).

4. After applying vacuum, fully open the stop valve with a hex

wrench.

5. Check that both indoor and outdoor connections are free

of air leakage.

Compound meter

-76cmHg

Pressure

gauge

Manifold

valve

Handle Hi

Charge

hose

Vacuum

pump

Stop valve

(gas valve)

Stop valve

(liquid valve)

Charge hose

Handle Lo

Outdoor condensation drainage (Heat pump type only)

When the unit is heating, the condensing water and defrosting

water can be out reliably through the drain house.

Installation:

Install the outdoor drain elbow in ɸ25 hole on the base

plate, and joint the drain hose to the elbow, so that the

waste water formed in the outdoor unit can be drained

out to a proper plate.

Chassis

Outdoor drain elbow

CHECK AFTER INSTALLATION AND TEST

OPERATION

Check after installation

Electrical Safety Check

1. If the supply voltage is as required.

2. If there is any faulty or miss connection in each of the power, signal and grounding wires.

3. If the grounding wire of the air conditioner is securely grounded.

Installation Safety Check

1. If the installation is secure.

2. If the water drain is smooth.

3. If the wiring and piping are correctly installed.

4. Check that no foreign matter or tools are left inside the unit.

5. Check the refrigerant pipeline is protected well.

Leak test of the refrigerant

Depending on the installation method, the following methods may be used to check for suspect leak, on areas

such as the four connections of the outdoor unit and the cores of the cut-off valves and t-valves:

1. Bubble method: Apply of spray a uniform layer of soap water over the suspected leak spot and observe carefully

for bubble.

2. lnstrument method: Checking for leak by pointing the probe of the leak detector according to the instruction to

the suspect points of leak.

Note: Make sure that the ventilation is good before checking.

20

ENG

Test Operation

• Verify that all piping and connection cables are well connected.

• Conﬁrm that the values at the gas side the liquid-side are fully open.

• Connect the power cord to an independent power socket.

• Install batteries in remote control.

Note: Make sure that the ventilation is good before testing.

Test Operation method:

1. Turn on the power and push the ON/OFF switch button of the remote controller to start the air conditioner.

2. Select COOL, HEAT (not available on cool-only models), SWING and other operation modes with the remote

controller and see if the operation is ok.

MAINTENANCE NOTICE

Qualiﬁcation requirements of maintenance personnel

Inspection of the Site

Operating Procedures

Attention:

For maintenance or scrap, please contact authorized service centers. Maintenance by unqualiﬁed person may

cause dangers. Feed air conditioner with R32 refrigerant, and maintain the air conditioner in strictly accordance

with manufacturer’s requirements. The chapter is mainly focused on special maintenance requirements for

appliance with R32 refrigerant. Ask repairer to read after-sales technical service handbook for detailed information.

1. Special training additional to usual refrigerating equipment repair procedures is required when equipment

with ﬂammable refrigerants is affected. In many countries, this training is carried out by national training

organisations that are accredited to teach the relevant national competency standards that may be set in

legislation. The achieved competence should be documented by a certiﬁcate.

2. The maintenance and repair of the air conditioner must be conducted according to the method

recommended by the manufacturer. If other professionals are needed to help maintain and repair the

equipment, it should be conducted under the supervision of individuals who have the qualiﬁcation to repair

AC equipped with ﬂammable refrigerant.

Safety inspection must be taken before maintaining equipment with R32 refrigerant to make sure the risk of ﬁre is

minimized. Check whether the place is well ventilated, whether anti-static and ﬁre prevention equipment is perfect.

While maintaining the refrigeration system, observe the following precautions before operating the system.

1. General work area:

All maintenance staff and others working in the local area shall be instructed on the nature of work being carried

out. Work in conﬁned spaces shall be avoided. The area around the workspace shall be sectioned off. Ensure that

the conditions within the area have been made safe by control of ﬂammable material.

2. Checking for presence of refrigerant:

The area shall be checked with an appropriate refrigerant detector prior to and during work, to ensure the

technician is aware of potentially toxic or ﬂammable atmospheres. Ensure that the leak detection equipment

being used is suitable for use with all applicable refrigerants, Le.non-sparking, adequately sealed or intrinsically

safe.

3. Presence of ﬁre extinguisher:

If any hot work is to be conducted on the refrigeration equipment or any associated parts, appropriate ﬁre

extinguishing equipment shall be available to hand. Have a dry powder or CO2 ﬁre extinguisher adjacent to the

charging area.

4. No ignition sources:

No person carrying out work in relation to a refrigeration system which involves exposing any pipe work shall

Pagina se încarcă ...

Tesla TC53P4-1832IA Manual de utilizare

Acest manual este potrivit și pentru

Tesla TC53P4-1832IA Manual de utilizare

Lucrări conexe

Alte documente