Asus Pro WS W790E-SAGE SE Manual de utilizare

Motherboard

Pro WS

W790E-SAGE

SE

ii

E22125

Revised Edition V2

June 2023

No part of this manual, including the products and software described in it, may be reproduced,

transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by

any means, except documentation kept by the purchaser for backup purposes, without the express

written permission of ASUSTeK COMPUTER INC. (“ASUS”).

Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless

such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the

product is defaced or missing.

ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS

OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS

DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,

INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,

LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),

EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM

ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.

SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR

INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,

AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO

RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN

THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.

Products and corporate names appearing in this manual may or may not be registered trademarks or

copyrights of their respective companies, and are used only for identification or explanation and to the

owners’ benefit, without intent to infringe.

iii

Contents

Safety information ....................................................................................................... v

About this guide ......................................................................................................... vi

Pro WS W790E-SAGE SE specifications summary................................................ vii

Connectors with shared bandwidth ........................................................................ xii

Package contents ..................................................................................................... xiii

Chapter 1: Product Introduction

1.1 Before you proceed ...................................................................................1-1

1.2 Motherboard layout ....................................................................................1-2

Chapter 2: Basic Installation

2.1 Building your PC system ...........................................................................2-1

2.1.1 Installing the CPU and heatsink .................................................. 2-1

2.1.2 DIMM installation.........................................................................2-3

2.1.3 M.2 installation ............................................................................ 2-4

2.1.4 Additional cooling kit installation ............................................... 2-13

2.1.5 Motherboard installation ............................................................ 2-14

2.1.6 ATX power connection .............................................................. 2-15

2.1.7 SATA device connection ........................................................... 2-19

2.1.8 SlimSAS connection..................................................................2-19

2.1.9 Front I/O connector ................................................................... 2-20

2.1.10 Expansion card installation ....................................................... 2-21

2.1.11 M.2 Wi-Fi module and antenna installation ............................... 2-22

2.2 BIOS update utility ................................................................................... 2-23

2.3 Motherboard rear and audio connections .............................................2-25

2.3.1 Rear I/O connection .................................................................. 2-25

2.3.2 Audio I/O connections ............................................................... 2-27

2.4 Starting up for the first time ....................................................................2-29

2.5 Turning off the computer ........................................................................2-29

Chapter 3: BIOS Support

3.1 Knowing BIOS ............................................................................................3-1

3.2 BIOS setup program ..................................................................................3-2

3.3 ASUS EzFlash Utility ..................................................................................3-3

3.4 ASUS CrashFree BIOS 3 utility ................................................................. 3-4

3.5 RAID configurations ..................................................................................3-5

iv

Appendix

Pro WS W790E-SAGE block diagram (for W-3400 CPU) ..................................... A-1

Pro WS W790E-SAGE block diagram (for W-2400 CPU) ..................................... A-2

Q-Code table ............................................................................................................ A-3

Notices .................................................................................................................... A-7

Warranty ................................................................................................................. A-12

ASUS contact information .................................................................................... A-14

Service and Support ............................................................................................. A-14

v

Safety information

Electrical safety

• To prevent electrical shock hazard, disconnect the power cable from the electrical

outlet before relocating the system.

• When adding or removing devices to or from the system, ensure that the power cables

for the devices are unplugged before the signal cables are connected. If possible,

disconnect all power cables from the existing system before you add a device.

• Before connecting or removing signal cables from the motherboard, ensure that all

power cables are unplugged.

• Seek professional assistance before using an adapter or extension cord. These

devices could interrupt the grounding circuit.

• Ensure that your power supply is set to the correct voltage in your area. If you are not

sure about the voltage of the electrical outlet you are using, contact your local power

company.

• If the power supply is broken, do not try to fix it by yourself. Contact a qualified service

technician or your retailer.

Operation safety

• Before installing the motherboard and adding devices on it, carefully read all the

manuals that came with the package.

• Before using the product, ensure all cables are correctly connected and the power

cables are not damaged. If you detect any damage, contact your dealer immediately.

• To avoid short circuits, keep paper clips, screws, and staples away from connectors,

slots, sockets and circuitry.

• Avoid dust, humidity, and temperature extremes. Do not place the product in any area

where it may become wet.

• Place the product on a stable surface.

• If you encounter technical problems with the product, contact a qualified service

technician or your retailer.

• Your motherboard should only be used in environments with ambient temperatures

between 0°C and 40°C.

Button/Coin Batteries Safety Information

WARNING

KEEP OUT OF REACH OF CHILDREN

Swallowing can lead to chemical burns,

perforation of soft tissue, and death. Severe

burns can occur within 2 hours of ingestion.

Seek medical attention immediately.

vi

About this guide

This user guide contains the information you need when installing and configuring the

motherboard.

How this guide is organized

This guide contains the following parts:

• Chapter 1: Product Introduction

This chapter describes the features of the motherboard and the new technology it

supports. It includes description of the switches, jumpers, and connectors on the

motherboard.

• Chapter 2: Basic Installation

This chapter lists the hardware setup procedures that you have to perform when

installing system components.

• Chapter 3: BIOS Support

This chapter tells how to boot into the BIOS and upgrade BIOS using the EZ Flash.

Where to find more information

Refer to the following sources for additional information and for product and software

updates.

1. ASUS website

The ASUS website (www.asus.com) provides updated information on ASUS hardware

and software products.

2. Optional documentation

Your product package may include optional documentation, such as warranty flyers,

that may have been added by your dealer. These documents are not part of the

standard package.

Conventions used in this guide

To ensure that you perform certain tasks properly, take note of the following symbols used

throughout this user guide.

CAUTION: Information to prevent damage to the components and injuries to

yourself when trying to complete a task.

IMPORTANT: Instructions that you MUST follow to complete a task.

NOTE: Tips and additional information to help you complete a task.

vii

Pro WS W790E-SAGE SE specifications summary

CPU

Intel® Socket LGA4677 for Xeon® W-3400 and W-2400 Series

Processors*

Supports Intel® Turbo Boost Max Technology 3.0

* Refer to www.asus.com for CPU support list.

Chipset Intel® W790 Chipset

Memory

8 x DIMM, Max. 2048GB, DDR5 4800 ECC Registered Memory*

8-Channel Memory Architecture

Supports Intel® Extreme Memory Profile (XMP)

* Supported memory types, data rate (speed), and number of DRAM modules

vary depending on the CPU and memory configuration, for more information

please refer to CPU/Memory Support list under the Support tab of product

information site or visit https://www.asus.com/support/.

Graphics 1 x VGA port from AST2600

Expansion Slots

Intel® Xeon® W-3400 Series Processors*

7 x PCIe 5.0 slots (Seven at x16/x16/x16/x16/x16/x8/x16)**

Intel® Xeon® W-2400 Series Processors*

4 x PCIe 5.0 slot(s) (Four at x16/x16/x16/x16)**

* Please check the PCIe bifurcation table at the support site

(https://www.asus.com/support/FAQ/1037507/).

** Please refer to the block diagrams in the Appendix for more details.

*** To ensure compatibility of the device installed, please refer to

https://www.asus.com/support/ for the list of supported peripherals.

Storage

Total supports 3 x M.2 slots and 8 x SATA 6Gb/s ports*

Intel® Xeon® W-3400 Series Processors

- M.2_1 slot (Key M), type 2242/2260/2280/22110 (supports PCIe 5.0

x4 mode)***

- M.2_2 slot (Key M), type 2242/2260/2280/22110 (supports PCIe 5.0

x4 mode)***

Intel® W790 Chipset**

- M.2_3 slot (Key M), type 2242/2260/2280/22110 (supports PCIe 4.0

x4 mode)

- SlimSAS_1 port supports PCIe 4.0 x4 mode NVMe device

- SlimSAS_2 port supports PCIe 4.0 x4 mode NVMe device

- 8 x SATA 6Gb/s ports

* Supports Intel® Virtual RAID on CPU (Intel® VROC) and Intel Volume

Management Device (Intel®VMD)

** Intel® VROC Technology supports PCIe RAID 0/1/5/10, SATA RAID 0/1/5/10.

VROC HW_Key is purchased separately.

*** M.2_1 and M.2_2 slots will be disabled once an Intel® Xeon® W-2400 Series

Processor is installed.

Ethernet

1 x Intel® dual 10Gb Ethernet

1 x Realtek 1Gb Ethernet

ASUS LANGuard

USB

Rear USB (Total 8 ports)

- 1 x USB 3.2 Gen 2x2 port (1 x USB Type-C®)

- 5 x USB 3.2 Gen 2 ports (4 x Type-A + 1 x USB Type-C®)

- 2 x USB 2.0 ports (2 x Type-A)

(continued on the next page)

viii

Pro WS W790E-SAGE SE specifications summary

USB

Front USB (Total 7 ports)

- 1 x USB 3.2 Gen 2 connector (supports USB Type-C®)

- 1 x USB 3.2 Gen 1 header supports 2 additional USB 3.2 Gen 1 ports

- 2 x USB 2.0 headers support 4 additional USB 2.0 ports

Audio

Realtek S1220A 7.1 Surround Sound High Definition Audio CODEC*

- Impedance sense for front and rear headphone outputs

- Internal audio Amplifier to enhance the highest quality sound for

headphone and speakers

- Supports: Jack-detection, Multi-streaming, Front Panel Jack-retasking

- High quality 120 dB SNR stereo playback output and 113 dB SNR

recording input (Line-in)

- Supports up to 32-Bit/192 kHz playback*

Audio Features

- Power pre-regulator reduces power input noise to ensure consistent

performance

- Rear optical S/PDIF out port

- Premium audio capacitors

- Dedicated audio PCB layers

- Unique de-pop circuit

* Due to limitations in HDA bandwidth, 32-Bit/192 kHz is not supported for 7.1

Surround Sound audio.

Back Panel I/O Ports

1 x USB 3.2 Gen 2x2 port (1 x USB Type-C)

5 x USB 3.2 Gen 2 ports (4 x Type-A + 1 x USB Type-C®)

2 x USB 2.0 ports (2 x Type-A)

1 x VGA port

2 x Intel® dual 10Gb Ethernet ports

1 x Realtek 1Gb Ethernet port

5 x Audio jacks

1 x Optical S/PDIF out port

1 x BIOS FlashBack™ button

1 x Clear CMOS button

Internal I/O connectors

Fan and Cooling related

1 x 4-pin CPU Fan header

1 x 4-pin CPU OPT Fan header

5 x 4-pin Chassis Fan headers

1 x W_PUMP+ header

Power related

2 x 24-pin Main Power connectors

4 x 8-pin +12V Power connectors

1 x 8-pin PCIe Power connector

1 x 6-pin PCIe Power connector

(continued on the next page)

ix

Pro WS W790E-SAGE SE specifications summary

Internal I/O connectors

Storage related

3 x M.2 slots (Key M)

2 x SlimSAS connectors

8 x SATA 6Gb/s ports

1 x VROC Key header

USB

1 x USB 3.2 Gen 2 connector (supports USB Type-C®)

1 x USB 3.2 Gen 1 header supports 2 additional USB 3.2 Gen 1 ports

2 x USB 2.0 headers support 4 additional USB 2.0 ports

Miscellaneous

1 x COM Port header

1 x FlexKey button

1 x Front Panel Audio header (AAFP)

1 x LN2 Mode jumper

1 x M.2 slot (Key E)

1 x ReTry button

1 x Safe Boot button

1 x SPI TPM header (14-1pin)

1 x Start button

1 x 20-3 pin System Panel header with Chassis intrude function

1 x Thermal Sensor header

BMC Related

1 x BMC switch

1 x VGA switch

1 x BMC LAN fixed IP switch

1 x IPMI switch

2 x Q_PSU switches

2 x PSU SMBus headers

1 x Front panel location LED header

1 x Location button header

1 x VPP_I2C header

1 x Micro SD card socket

1 x BMC Thermal Sensor header

1 x BMC LED

1 x Location LED

1 x Message LED header

Special Features

Extreme OC Kit

- FlexKey button

- LN2 Mode

- ReTry button

- Safe boot button

- Start button

(continued on the next page)

x

Pro WS W790E-SAGE SE specifications summary

Special Features

Extreme Engine Digi+

- 10K Black Metallic Capacitors

- MicroFine Alloy Choke

ASUS 5X PROTECTION III

- DIGI+ VRM (- Digital power design with DrMOS)

- ESD Guards

- LANGuard

- Overvoltage Protection

- Safeslot

- Stainless-Steel Back I/O

ASUS Q-Design

- M.2 Q-Latch

- Q-Code

- Q-Connector

- Q-DIMM

- Q-LED (CPU [red], DRAM [yellow], VGA [white], Boot Device [yellow

green])

- Q-Slot

ASUS Thermal Solution

- M.2 heatsink backplate

- M.2 heatsink

- Steel backplate

- VRM heatsink design

ASUS EZ DIY

- BIOS FlashBack™ button

- BIOS FlashBack™ LED

- Caterr1 LED

- Box Headers

- Clear CMOS button

- ProCool II

- Pre-mounted I/O shield

- SafeSlot

- SafeDIMM

Bespoke Motherboard Design & Business Focused Features

- 24/7 Reliability

- Overcurrent Protection

(continued on the next page)

xi

Pro WS W790E-SAGE SE specifications summary

Software Features

ASUS Exclusive Software

Armoury Crate

- Fan Xpert 4

AI Suite 3

- TPU

- DIGI+ VRM

- Turbo app

- PC Cleaner

ASUS CPU-Z

IT Management software supported

- ASUS Control Center Express(ACCE)

Norton 360 Deluxe (60 Days Free Trial)

WinRAR

UEFI BIOS

ASUS EZ DIY

- ASUS CrashFree BIOS 3

- ASUSTeK. EzFlash Utility

FlexKey

BIOS 512 Mb Flash ROM, UEFI AMI BIOS

Manageability WOL by PME, PXE (UEFI mode)

Operating System Windows® 11

Windows® 10 64-bit

Form Factor EEB Form Factor

12 inch x 13 inch (30.5 cm x 33 cm)

• Specifications are subject to change without notice. Please refer to the ASUS website

for the latest specifications.

• For more information on downloading and installing drivers and utilities for your

motherboard, please scan the QR code below:

xii

Connectors with shared bandwidth

A

Configuration

Intel® Xeon®

W-3400

Processors

Intel® Xeon®

W-2400

Processors

A

PCIEX16(G5)_1 x16 x16

PCIEX16(G5)_2 x16 -

PCIEX16(G5)_3 x16 x16

PCIEX16(G5)_4 x16 -

PCIEX16(G5)_5 x16 x16

PCIEX16(G5)_6 x8 -

PCIEX16(G5)_7 x16 x16

Connect a chassis fan to the chassis fan connectors when using multiple graphics cards

for better thermal environment.

We recommend selecting a chassis case which supports 7 or more expansion slots.

xiii

Package contents

Check your motherboard package for the following items.

Motherboard 1 x Pro WS W790E-SAGE SE

Cables 4 x SATA 6Gb/s cables

1 x Thermistor cable pack

Miscellaneous

1 x VRM fan holder

1 x Q-connector

1 x M.2 rubber package

1 x M.2 backplate rubber package

1 x Screw package for M.2 Key E

1 x CPU carrier for LGA 4677 (E1A)

1 x CPU carrier for LGA 4677 (E1B)

Documentation 1 x User guide

1 x ACC Express Activation Key Card

If any of the above items is damaged or missing, contact your retailer.

xiv

Pro WS W790E-SAGE SE 1-1

Chapter 1

Product Introduction

1

Chapter 1: Product Introduction

• Unplug the power cord from the wall socket before touching any component.

• Before handling components, use a grounded wrist strap or touch a safely grounded

object or a metal object, such as the power supply case, to avoid damaging them due

to static electricity.

• Hold components by the edges to avoid touching the ICs on them.

• Whenever you uninstall any component, place it on a grounded antistatic pad or in

the bag that came with the component.

• Before you install or remove any component, ensure that the ATX power supply is

switched off or the power cord is detached from the power supply. Failure to do so

may cause severe damage to the motherboard, peripherals, or components.

• The pin definitions in this chapter are for reference only. The pin names depend on

the location of the header/jumper/connector.

• For more information on installing your motherboard, please scan the QR code

below:

1.1 Before you proceed

Take note of the following precautions before you install motherboard components or

change any motherboard settings.

1-2 Chapter 1: Product Introduction

Chapter 1

1.2 Motherboard layout

Pro WS W790E-SAGE SE 1-3

Chapter 1

Layout contents Page

1. CPU socket 1-4

2. DIMM slots 1-5

3. Expansion slots 1-7

4. Fan headers 1-9

5. Power connectors 1-10

6. M.2 slot 1-11

7. Micro SD card socket 1-12

8. SATA 6GB/s port 1-13

9. SlimSAS port 1-13

10. USB 3.2 Gen 2 Type-C® Front Panel connector 1-14

11. USB 3.2 Gen 1 header 1-14

12. USB 2.0 connector 1-15

13. BMC switch 1-15

14. BMC Thermal Sensor header 1-16

15. COM Port header 1-16

16. Fixed Dedicated BMC LAN IP switch 1-17

17. FlexKey button (Reset) 1-17

18. Front Panel Audio header 1-18

19. IPMI switch 1-18

20. LED headers 1-19

21. LN2 Mode jumper 1-19

22. Location button and LED headers 1-20

23. M.2 slot (Key E) 1-20

24. Power Supply SMBus connector 1-21

25. ReTry button 1-21

26. Safe Boot button 1-22

27. SMART PSU switch 1-22

28. Start button 1-23

29. System Panel header 1-24

30. Thermal Sensor header 1-25

31. TPM header 1-25

32. VGA Switch 1-26

33. VPP_I2C header 1-26

34. VROC Key header 1-27

35. Q-Code LED 1-28

36. Q LEDs 1-29

37. BMC LED 1-29

38. Location LED 1-30

39. Message LED 1-30

40. Processor Catastrophic Error LED 1-31

41. 8-pin Power Plug LED 1-31

42. 8-pin PCIe Power Plug LED 1-32

1-4 Chapter 1: Product Introduction

Chapter 1

1. CPU socket

The motherboard comes with a LGA4677 socket designed for Intel® Xeon® W-3400 and

W-2400 Series Processors.

• Ensure that you install the correct CPU designed for LGA4677 socket only. DO NOT

install a CPU designed for other sockets on the LGA4677 socket.

• The CPU fits in only one correct orientation. DO NOT force the CPU into the socket

to prevent bending the connectors on the socket and damaging the CPU.

• Ensure that all power cables are unplugged before installing the CPU.

• Upon purchase of the motherboard, ensure that the PnP cap is on the socket and

the socket contacts are not bent. Contact your retailer immediately if the PnP cap

is missing, or if you see any damage to the PnP cap/socket contacts/motherboard

components. ASUS will shoulder the cost of repair only if the damage is shipment/

transit-related.

• Keep the cap after installing the motherboard. ASUS will process Return

Merchandise Authorization (RMA) requests only if the motherboard comes with the

cap on the socket.

• The product warranty does not cover damage to the socket contacts resulting from

incorrect CPU installation/removal, or misplacement/loss/incorrect removal of the

PnP cap.

Pro WS W790E-SAGE SE 1-5

Chapter 1

2. DIMM slots

The motherboard comes with Dual Inline Memory Modules (DIMM) slots designed for DDR5

(Double Data Rate 5) memory modules.

A DDR5 memory module is notched differently from a DDR, DDR2, DDR3, or DDR4

module. DO NOT install a DDR, DDR2, DDR3, or DDR4 memory module to the DDR5

slot.

• Intel® Xeon® W-2400 Series Processors do not support DIMM_C1, DIMM_D1,

DIMM_G1, and DIMM_H1

• The DIMM slots for this motherboard are one-DIMM per channel. You can install

DIMMs to any of the DIMM slots in any order.

1-6 Chapter 1: Product Introduction

Chapter 1

Memory configurations

You may install ECC DDR5 RDIMMs into the DIMM sockets.

You may install varying memory sizes in between channels. The system maps the total

size of the lower-sized channel for the dual-channel configuration. Any excess memory

from the higher-sized channel is then mapped for single-channel operation.

• The default memory operation frequency is dependent on its Serial Presence Detect

(SPD), which is the standard way of accessing information from a memory module.

Under the default state, some memory modules for overclocking may operate at a

lower frequency than the vendor-marked value.

• For system stability, use a more efficient memory cooling system to support a full

memory load or overclocking condition.

• Always install the DIMMS with the same CAS Latency. For an optimum compatibility,

we recommend that you install memory modules of the same version or data code

(D/C) from the same vendor. Check with the vendor to get the correct memory

modules.

• Visit the ASUS website for the latest QVL.

Pagina se încarcă ...

Asus Pro WS W790E-SAGE SE Manual de utilizare

Asus Pro WS W790E-SAGE SE Manual de utilizare

în alte limbi

Lucrări conexe

Alte documente