Asus ProArt B760-CREATOR Manual de utilizare

Marca: Asus

Model: ProArt B760-CREATOR

Categorie: Plăci de bază

Tip: Manual de utilizare

Motherboard

ProArt B760-CREATOR

E21817

First Edition

March 2023

No part of this manual, including the products and software described in it, may be reproduced,

transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any

means, except documentation kept by the purchaser for backup purposes, without the express written

permission of ASUSTeK COMPUTER INC. (“ASUS”).

Product warranty or service will not be extended if: (1) the product is repaired, modied or altered, unless

such repair, modication of alteration is authorized in writing by ASUS; or (2) the serial number of the

product is defaced or missing.

ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS

OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS

DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,

INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,

LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),

EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY

DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.

SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR

INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,

AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO

RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS

MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.

Products and corporate names appearing in this manual may or may not be registered trademarks or

copyrights of their respective companies, and are used only for identication or explanation and to the

owners’ benet, without intent to infringe.

iii

Contents

Safety information ...................................................................................................... iv

About this guide .......................................................................................................... v

Package contents ....................................................................................................... vi

ProArt B760-CREATOR specifications summary .................................................... vi

Chapter 1: Product Introduction

1.1 Before you proceed ......................................................................................1-1

1.2 Motherboard overview .................................................................................1-2

1.3 Central Processing Unit (CPU) ..................................................................1-10

1.4 System memory ..........................................................................................1-12

1.5 M.2 installation ............................................................................................1-14

Chapter 2: BIOS and RAID Support

2.1 Knowing BIOS ...............................................................................................2-1

2.2 BIOS Setup program ....................................................................................2-2

2.3 ASUS EZ Flash 3 ...........................................................................................2-3

2.4 ASUS CrashFree BIOS 3 .............................................................................. 2-4

2.5 RAID configurations .....................................................................................2-5

Appendix

Notices ..................................................................................................................... A-1

Warranty ................................................................................................................... A-5

ASUS contact information ...................................................................................... A-7

Service and Support ............................................................................................... A-7

Safety information

Electrical safety

• To prevent electrical shock hazard, disconnect the power cable from the electrical outlet

before relocating the system.

• When adding or removing devices to or from the system, ensure that the power cables

for the devices are unplugged before the signal cables are connected. If possible,

disconnect all power cables from the existing system before you add a device.

• Before connecting or removing signal cables from the motherboard, ensure that all power

cables are unplugged.

• Seek professional assistance before using an adapter or extension cord. These devices

could interrupt the grounding circuit.

• Ensure that your power supply is set to the correct voltage in your area. If you are not

sure about the voltage of the electrical outlet you are using, contact your local power

company.

• If the power supply is broken, do not try to x it by yourself. Contact a qualied service

technician or your retailer.

Operation safety

• Before installing the motherboard and adding components, carefully read all the manuals

that came with the package.

• Before using the product, ensure all cables are correctly connected and the power cables

are not damaged. If you detect any damage, contact your dealer immediately.

• To avoid short circuits, keep paper clips, screws, and staples away from connectors,

slots, sockets and circuitry.

• Avoid dust, humidity, and temperature extremes. Do not place the product in any area

where it may become wet.

• Place the product on a stable surface.

• If you encounter technical problems with the product, contact a qualied service

technician or your retailer.

• Your motherboard should only be used in environments with ambient temperatures

between 0°C and 40°C.

Button/Coin Batteries Safety Information

WARNING

KEEP OUT OF REACH OF CHILDREN

Swallowing can lead to chemical burns,

perforation of soft tissue, and death.

Severe burns can occur within 2 hours

of ingestion. Seek medical attention

immediately.

About this guide

This user guide contains the information you need when installing and conguring the

motherboard.

How this guide is organized

This guide contains the following parts:

• Chapter 1: Product Introduction

This chapter describes the features of the motherboard and the new technology it

supports. It includes descriptions of the switches, jumpers, and connectors on the

motherboard.

• Chapter 2: BIOS and RAID Support

This chapter tells how to boot into the BIOS, upgrade BIOS using the EZ Flash Utility

and support on RAID.

Where to find more information

Refer to the following sources for additional information and for product and software

updates.

1. ASUS website

The ASUS website (www.asus.com) provides updated information on ASUS hardware

and software products.

2. Optional documentation

Your product package may include optional documentation, such as warranty flyers,

that may have been added by your dealer. These documents are not part of the

standard package.

Conventions used in this guide

To ensure that you perform certain tasks properly, take note of the following symbols used

throughout this user guide.

CAUTION: Information to prevent damage to the components and injuries to

yourself when trying to complete a task.

IMPORTANT: Instructions that you MUST follow to complete a task.

NOTE: Tips and additional information to help you complete a task.

ProArt B760-CREATOR specifications summary

CPU

Intel® Socket LGA1700 for 13th Gen Intel® Core™ & 12th Gen Intel®

Core™, Pentium® Gold and Celeron® Processors*

Supports Intel® 10 nm CPU

Supports Intel® Turbo Boost Technology 2.0 and Intel® Turbo Boost Max

Technology 3.0**

* Refer to www.asus.com for CPU support list.

** Intel® Turbo Boost Max Technology 3.0 support depends on the CPU types.

Chipset Intel® B760 Chipset

Memory

4 x DIMM slots, Max. 128GB, DDR5 Non-ECC, Un-buffered Memory*

Dual Channel Memory Architecture

Supports Intel® Extreme Memory Prole (XMP)

OptiMem II

* Supported memory types, data rate (speed), and number of DRAM modules vary

depending on the CPU and memory configuration, for more information please

refer to CPU/Memory Support list under the Support tab of product information

site or visit https://www.asus.com/support/.

* Non-ECC, un-buffered DDR5 memory supports On-Die ECC function.

Graphics

1 x DisplayPort**

1 x HDMI™ port***

Graphics specifications may vary between CPU types.

Please refer to

www.intel.com for any updates.

** Supports max. 8K@60Hz as specified in DisplayPort 1.4.

*** Supports 4K@60Hz as specified in HDMI™ 2.1.

Expansion Slots

Intel® 13th &12th Gen Processors

1 x PCIe 5.0/4.0/3.0 x16 slot

Intel® B760 Chipset

1 x PCIe 4.0 x16 slot (supports x4 mode)

1 x PCIe 3.0 x1 slot*

Note: To ensure compatibility of the device installed, please refer to

https://www.asus.com/support/ for the list of supported peripherals.

PCIE X1 shares bandwidth with M.2_2 slot. PCIE X1 will be disabled when

M.2_2 runs at PCIe x4 mode by manually enabled.

(continued on the next page)

Package contents

Check your motherboard package for the following items.

Motherboard 1 x ProArt B760-CREATOR motherboard

Cables 2 x SATA 6Gb/s cables

Miscellaneous

2 x M.2 Rubber packages

1 x Screw package for M.2 Key E

1 x ProArt ruler

1 x Q-connector

Documentation 1 x ACC Express Activation Key Card

1 x User guide

If any of the above items is damaged or missing, contact your retailer.

vii

ProArt B760-CREATOR specifications summary

Storage

Total supports 3 x M.2 slots and 4 x SATA 6Gb/s ports*

Intel® 13th &12th Gen Processors

M.2_1 slot (Key M), type 2242/2260/2280/22110

- Intel® 13th & 12th Gen processors support PCIe 4.0 x4 mode

Intel® B760 Chipset

M.2_2 slot (Key M), type 2242/2260/2280/22110 (supports PCIe 3.0 x4

mode)**

M.2_3 slot (Key M), type 2242/2260/2280/22110 (supports PCIe 4.0 x4 mode)

4 x SATA 6Gb/s ports

* Intel® Rapid Storage Technology supports SATA RAID 0/1/5/10.

** Intel® Rapid Storage Technology supports Intel® Optane Memory H Series on PCH

attached M.2 slots.

*** M.2_2 slot shares bandwidth with PCIE X1 and WiFi Key E. M.2_2 will run at PCI

3.0 x2 mode when either device is detected at PCIE x1 or WiFi Key E slot.

Ethernet

1 x Realtek 2.5Gb Ethernet

1 x Intel® 1Gb Ethernet

ASUS LANGuard

Wireless &

Bluetooth®

M.2 slot only (Key E, CNVi & PCIe)*

* Wi-Fi module is sold separately.

USB

Rear USB (Total 9 ports)

1 x USB 3.2 Gen 2 (10G) port (1 x USB Type-C®)

4 x USB 3.2 Gen 1 (5G) ports (4 x Type-A)

4 x USB 2.0 ports (4 x Type-A)

Front USB (Total 7 ports)

1 x USB 3.2 Gen 2x2 (20G) connector (supports USB Type-C® with up to 60W

PD 3.0/QC 4+)

1 x USB 3.2 Gen 1 (5G) header supports 2 additional USB 3.2 Gen 1 ports

2 x USB 2.0 headers support 4 additional USB 2.0 ports

Audio

Realtek 7.1 Surround Sound High Definition Audio CODEC*

- Supports: Jack detection, Multi-streaming, Front Panel Jack-retasking

- Supports up to 24-Bit/192kHz playback

Audio Features

- Premium audio capacitors

- Dedicated audio PCB layers

- Audio cover

- Unique de-pop circuit

Back Panel I/O Ports

1 x USB 3.2 Gen 2 (10G) port (1 x USB Type-C®)

4 x USB 3.2 Gen 1 (5G) ports (4 x Type-A)

4 x USB 2.0 ports (4 x Type-A)

1 x DisplayPort

1 x HDMI™ port

1 x Realtek 2.5Gb Ethernet port

1 x Intel® 1Gb Ethernet port

5 x Audio jacks

1 x Optical S/PDIF out port

(continued on the next page)

viii

ProArt B760-CREATOR specifications summary

Internal I/O

Connectors

Fan and Cooling related

1 x 4-pin CPU Fan header

1 x 4-pin CPU OPT Fan header

1 x 4-pin AIO Pump header

4 x 4-pin Chassis Fan headers

Power related

1 x 24-pin Main Power connector

1 x 8-pin +12V Power connector

1 x 4-pin +12V Power connector

1 x 6-pin PD_12V Power connector

Storage related

3 x M.2 slots (Key M)

4 x SATA 6Gb/s ports

USB

1 x USB 3.2 Gen 2x2 (20G) connector (supports USB Type-C® with 60W PD 3.0 /QC 4+)

1 x USB 3.2 Gen 1 (5G) header supports 2 additional USB 3.2 Gen1 ports

2 x USB 2.0 headers support 4 additional USB 2.0 ports

Miscellaneous

3 x Addressable Gen 2 headers

1 x Aura RGB header

1 x Clear CMOS header

1 x COM Port header

1 x Front Panel Audio header (AAFP)

1 x M.2 slot (Key E)

1 x SPI TPM header (14-1pin)

1 x 20-5 pin System Panel header

1 x Thermal Sensor header

1 x Thunderbolt™ header

Special

Features

ASUS 5X PROTECTION III

- DIGI+ VRM (- Digital power design with DrMOS)

- Enhanced DRAM Overcurrent Protection

- ESD Guards

- LANGuard

- Overvoltage Protection

- SafeSlot

- Stainless-Steel Back I/O

ASUS Q-Design

- M.2 Q-Latch

- Q-Connector

- Q-DIMM

- Q-LED (CPU [red], DRAM [yellow], VGA [white], Boot Device [yellow green])

- Q-Slot

ASUS Thermal Solution

- Flexible M.2 heatsink

- VRM heatsink design

(continued on the next page)

ProArt B760-CREATOR specifications summary

Special Features

ASUS EZ DIY

- ProCool

- Pre-mounted I/O shield

Aura Sync

- Aura RGB header

- Addressable Gen 2 headers

Software Features

ASUS Exclusive Software

Armoury Crate

- Aura Creator

- Aura Sync

- Fan Xpert 4

- Power Saving

- Two-Way AI Noise Cancelation

AI Suite 3

- Performance And Power Saving Utility

DIGI+ VRM

Turbo app

ASUS CPU-Z

IT Management software supported

- ASUS Control Center Express (ACCE)

ProArt Creator Hub

CreationFirst

Norton 360 Deluxe (60 Days Free Trial)

WinRAR

UEFI BIOS

ASUS EZ DIY

- ASUS CrashFree BIOS 3

- ASUS EZ Flash 3

- ASUS UEFI BIOS EZ Mode

BIOS 128 Mb Flash ROM, UEFI AMI BIOS

Manageability WOL by PME, PXE

Operating System Windows® 11, Windows® 10 64-bit

Form Factor ATX Form Factor

12 inch x 9.6 inch (30.5 cm x 24.4 cm)

• Specications are subject to change without notice. Refer to the ASUS website for the

latest specications.

• For more information on downloading and installing drivers and utilities for your

motherboard, please scan the QR code below:

1-1

ProArt B760-CREATOR

Product Introduction

1.1 Before you proceed

Take note of the following precautions before you install motherboard components or change

any motherboard settings.

• Unplug the power cord from the wall socket before touching any component.

• Before handling components, use a grounded wrist strap or touch a safely grounded

object or a metal object, such as the power supply case, to avoid damaging them due

to static electricity.

• Hold components by the edges to avoid touching the ICs on them.

• Whenever you uninstall any component, place it on a grounded antistatic pad or in the

bag that came with the component.

• Before you install or remove any component, ensure that the ATX power supply is

switched off or the power cord is detached from the power supply. Failure to do so

may cause severe damage to the motherboard, peripherals, or components.

• The pin denitions in this chapter are for reference only. The pin names depend on the

location of the header/jumper/connector.

• For more information on installing your motherboard, please scan the QR code below:

1-2

1.2.1 Layout contents

1. CPU socket

The motherboard comes with a LGA1700 socket designed for 13th Gen Intel® Core™ & 12th

Gen Intel® Core™, Pentium® Gold and Celeron® Processors.

For more details, refer to Central Processing Unit (CPU).

Chapter 1: Product Introduction

1.2 Motherboard overview

DDR5 DIMM_A1 (64bit, 288-pin module)

DDR5 DIMM_A2 (64bit, 288-pin module)

DDR5 DIMM_B1 (64bit, 288-pin module)

DDR5 DIMM_B2 (64bit, 288-pin module)

LGA1700

CHA_FAN1

PCIE SATA

4.0 X4

CPU_FAN CPU_OPT

AIO_PUMP

M.2_2(SOCKET3)

M.2_3(SOCKET3)

M.2(WIFI)

M.2_1(SOCKET3)

PCIE SATA

4.0 X4

M.2_3(SOCKET3)

PCIE SATA

3.0 X4

M.2_2(SOCKET3)

PANEL

AAFP

COM COM_DEBUG

ATX_12V_1

ATX_PWRPD_12V_PWR

U32G1_910

U32G2X2_C1

Intel®

B760

Intel

Ethernet

RTL

Ethernet

BATTERY

HDMI_DP

USB_E5678

LAN2_U32G1_E34

LAN1_U32G1_E12

Super

I/O

2280

2260

2242

TPM

228022110

22110

2260 2242

2280 2211022602242

PCIEX1(G3)

PCIEX16(G4)

PCIEX16(G5)

USB_78

USB_56

Audio Codec

U32G2_C3

30.5cm(12in)

SATA6G_12SATA6G_34

256Mb

BIOS

TB_HEADER

RGB_HEADER

ADD_GEN 2_1

ADD_GEN 2_2

ADD_GEN 2_3

ATX_12V_2

PLUG_8PIN_PWR

DIGI+

VRM

CHA_FAN3

CHA_FAN4

CHA_FAN2

CLRTC

T-SENSOR

24.4cm(9.6in)

CPU

DRAM

VGA

BOOT

AUDIO

1st

20 16

1415

522 214 124

11 13 19

Unplug the power cord before installing or removing the motherboard. Failure to do so can

cause you physical injury and damage motherboard components.

1-3

2. DDR5 DIMM slots

The motherboard comes with Dual Inline Memory Modules (DIMM) slots designed for DDR5

(Double Data Rate 5) memory modules.

For more details, refer to System memory.

3. Expansion slots

This motherboard supports two PCIe x16 graphics cards and one PCIe 3.0 x1 network card,

SCSI card or other card that complies with the PCI Express specication.

4. Fan headers

The Fan headers allow you to connect fans to cool the system.

Header Max.

Current

Max.

Power Default Speed Shared

Control

CPU_FAN 1A 12W Q-Fan Controlled A

CPU_OPT 1A 12W Q-Fan Controlled A

AIO_PUMP 1A 12W Full-Speed -

CHA_FAN1 1A 12W Q-Fan Controlled -

CHA_FAN2 1A 12W Q-Fan Controlled -

CHA_FAN3 1A 12W Q-Fan Controlled -

CHA_FAN4 1A 12W Q-Fan Controlled -

5. Power connectors

These Power connectors allow you to connect your motherboard to a power supply. The

power supply plugs are designed to t in only one orientation. Find the proper orientation and

push down rmly until the power supply plugs are fully inserted.

Ensure to connect the 8-pin power plug or connect both the 8-pin and 4-pin power plugs.

• We recommend that you use a PSU with a higher power output when conguring a

system with more power-consuming devices. The system may become unstable or

may not boot up if the power is inadequate.

• If you want to use two high-end PCI Express x16 cards, use a PSU with 1000W power

or above to ensure the system stability.

6. M.2 slots (Key M)

The M.2 slots allow you to install M.2 devices such as M.2 SSD modules.

• Intel® 13th & 12th Gen Processors

M.2_1 slot (Key M), type 2242/2260/2280/22110

- Intel® 13th &12th processors support PCIe 4.0 x4 mode

• Intel® B760 Chipset

M.2_2 slot (Key M), type 2242/2260/2280/22110 (supports PCIe 3.0 x4 mode)

M.2_3 slot (Key M), type 2242/2260/2280/22110 (supports PCIe 4.0 x4 mode)

• M.2_2 slot shares bandwidth with PCIE X1 and WiFi Key E. M.2_2 will run at PCI 3.0

x2 mode when either device is detected at PCIE x1 or WiFi Key E slot.

The M.2 SSD module is purchased separately.

FAN PWM

FAN IN

FAN PWR

GND

FAN PWM

FAN IN

FAN PWR

GND

FAN PWR

FAN IN

FAN PWM

ProArt B760-CREATOR

1-4

7. SATA 6Gb/s ports

The SATA 6Gb/s ports allow you to connect SATA devices such as optical disc drives and

hard disk drives via SATA cables.

8. USB 3.2 Gen 2x2 Type-C® connector (supports USB Type-C®

with 60W PD 3.0/QC 4+)

The USB 3.2 Gen 2x2 Type-C® connector allows you to connect a USB

3.2 Gen 2x2 Type-C® module for additional USB 3.2 Gen 2x2 ports on

the front panel. The USB 3.2 Gen 2x2 Type-C® connector provides data

transfer speeds of up to 20 Gb/s and PD 3.0/QC 4+ support for up to DC

60W fast charging technology.

• The USB 3.2 Gen 2x2 Type-C® module is purchased separately.

• For PD 3.0/QC 4+ support, ensure to connect the 6-pin PD_12V_PWR connector.

• PD 3.0/QC 4+ up to DC 60W fast charging technology is only supported on CC Logic

Devices. In S5 (Soft Off State), PD 3.0/QC 4+ only provides power delivery of up to

7.5W.

9. USB 3.2 Gen 1 header

The USB 3.2 Gen 1 header allows you to connect a USB 3.2 Gen

1 module for additional USB 3.2 Gen 1 ports. The USB 3.2 Gen 1

header provides data transfer speeds of up to 5 Gb/s.

The USB 3.2 Gen 1 module is purchased separately.

10. USB 2.0 headers

The USB 2.0 headers allow you to connect USB modules for additional USB 2.0

ports. The USB 2.0 headers provide data transfer speeds of up to 480 Mb/s.

DO NOT connect a 1394 cable to the USB connectors. Doing so will damage

the motherboard!

The USB 2.0 module is purchased separately.

11. Addressable Gen 2 headers

The Addressable Gen 2 headers allow you to connect individually addressable

RGB WS2812B LED strips or WS2812B based LED strips.

The Addressable Gen 2 headers support WS2812B addressable RGB LED strips (5V/Data/

Ground), with a maximum power rating of 3A (5V), and the addressable headers on this

board can handle a combined maximum of 500 LEDs.

Before you install or remove any component, ensure that the power supply is switched off

or the power cord is detached from the power supply. Failure to do so may cause severe

damage to the motherboard, peripherals, or components.

USB3+5V

IntA_P1_SSRX-

IntA_P1_SSRX+

GND

IntA_P1_SSTX-

IntA_P1_SSTX+

GND

IntA_P1_D-

IntA_P1_D+

GND

PIN 1

USB3+5V

IntA_P2_SSRX-

IntA_P2_SSRX+

GND

IntA_P2_SSTX-

IntA_P2_SSTX+

GND

IntA_P2_D-

IntA_P2_D+

USB+5V

USB_P1-

USB_P1+

GND

USB+5V

USB_P2-

USB_P2+

GND

PIN 1

ADD_GEN 2

+5V

Data

Ground

PIN 1

Chapter 1: Product Introduction

1-5

• Actual lighting and color will vary with LED strip.

• If your LED strip does not light up, check if the addressable RGB LED strip is

connected in the correct orientation, and the 5V connector is aligned with the 5V

header on the motherboard.

• The addressable RGB LED strip will only light up when the system is powered on.

• The addressable RGB LED strip is purchased separately.

12. Aura RGB header

The Aura RGB header allows you to connect RGB LED strips.

The Aura RGB header supports 5050 RGB multi-color LED strips (12V/G/R/B), with a

maximum power rating of 3A (12V), and no longer than 3m.

Before you install or remove any component, ensure that the ATX power supply is switched

off or the power cord is detached from the power supply. Failure to do so may cause severe

damage to the motherboard, peripherals, or components.

• Actual lighting and color will vary with LED strip.

• If your LED strip does not light up, check if the RGB LED extension cable and the

RGB LED strip are connected in the correct orientation, and the 12V connector is

aligned with the 12V header on the motherboard.

• The LED strip will only light up when the system is powered on.

• The LED strip is purchased separately.

13. Clear CMOS header

The Clear CMOS header allows you to clear the Real Time Clock (RTC) RAM in

the CMOS, which contains the date, time, system passwords, and system setup

parameters.

To erase the RTC RAM:

1. Turn OFF the computer and unplug the power cord.

2. Short-circuit pin 1-2 with a metal object or jumper cap for about 5-10 seconds.

3. Plug the power cord and turn ON the computer.

4. Hold down the <Del> key during the boot process and enter BIOS setup to

re-enter data.

DO NOT short-circuit the pins except when clearing the RTC RAM. Short-circuiting or

placing a jumper cap will cause system boot failure!

If the steps above do not help, remove the onboard button cell battery and short the two

pins again to clear the CMOS RTC RAM data. After clearing the CMOS, reinstall the button

cell battery.

14. COM Port header

The COM (Serial) Port header allows you to connect a COM port module.

Connect the COM port module cable to this header, then install the module to a

slot opening on the system chassis.

The COM port module is purchased separately.

CLRTC

+3V_BAT

GND

PIN 1

COM

PIN 1

DCD

TXD

GND

RTS

RXD

DTR

DSR

CTS

ProArt B760-CREATOR

1-6

15. Front Panel Audio header

The Front Panel Audio header is for a chassis-mounted front panel audio I/O

module that supports HD Audio. Connect one end of the front panel audio I/O

module cable to this header.

We recommend that you connect a high-denition front panel audio

module to this header to avail of the motherboard’s high-denition audio

capability.

16. M.2 slot (Key E)

The M.2 slot (Key E) allows you to install an M.2 Wi-Fi module (E-key, type 2230).

Wi-Fi module is sold separately.

17. SPI TPM header

This header supports a Trusted Platform Module (TPM)

system with a Serial Peripheral Interface (SPI), allowing you

to securely store keys, digital certicates, passwords, and

data. A TPM system also helps enhance network security,

protects digital identities, and ensures platform integrity.

SPI TPM module is purchased separately.

18. System Panel header

This header supports several chassis-mounted functions.

• System Power LED header (PLED)

The 2-pin and/or 3-1 pin headers allow you to connect the

System Power LED. The System Power LED lights up when the

system is connected to a power source, or when you turn on the

system power, and blinks when the system is in sleep mode.

• Storage Device Activity LED header (HDD_LED)

The 2-pin header allows you to connect the Storage Device

Activity LED. The Storage Device Activity LED lights up or

blinks when data is read from or written to the storage device or

storage device add-on card.

• System Warning Speaker header (SPEAKER)

The 4-pin header allows you to connect the chassis-mounted system warning speaker.

The speaker allows you to hear system beeps and warnings.

• Power Button/Soft-off Button header (PWRSW)

The 2-pin header allows you to connect the system power button. Press the power

button to power up the system, or put the system into sleep or soft-off mode

(depending on the operating system settings).

• Reset button header (RESET)

The 2-pin header allows you to connect the chassis-mounted reset button. Press the

reset button to reboot the system.

AAFP

AGND

SENSE1_RETUR

SENSE2_RETUR

PORT1 L

PORT1 R

PORT2 R

SENSE_SEND

PORT2 L

HD-audio-compliant

pin definition

TPM

PIN 1

VCCSPI

S_PLTRST#

+3V_SPI

F_SPI_CS0#_R

T_SPI_MISO

F_SPI_HOLD#_R

S_SPI_TPM_IRQ#

S_SPI_TPM_CS2#

TPM_DETECT_L

GND

T_SPI_CLK

T_SPI_MOSI

PLED+

PLED-

PWRBTN#

GND

+5V

Ground

Speaker

HDD_LED+

HDD_LED-

Ground

RSTCON#

PLED+

PLED-

PIN 1

PLED

SPEAKER

PANEL

HDD_LED

PWRSW

RESET

* Requires an ATX power supply

Chapter 1: Product Introduction

1-7

19. Thermal Sensor header

The Thermal Sensor header allows you to connect a sensor to monitor the temperature of the

devices and the critical components inside the motherboard. Connect the thermal sensor and

place it on the device or the motherboard’s component to detect its temperature.

The thermal sensor is purchased separately.

20. Thunderbolt™ header

The Thunderbolt™ header allows you to connect an add-on Thunderbolt™

I/O card that supports Intel®’s Thunderbolt™ Technology, allowing you to

connect Thunderbolt™-enabled devices to form a daisy chain-conguration.

• The add-on Thunderbolt™ I/O card and Thunderbolt™ cables are

purchased separately.

• Please visit the ofcial website of your purchased Thunderbolt card

for more details on compatibility.

The Thunderbolt™ card can only be used when installed to the

PCIEX16(G4) slot. Ensure to install your Thunderbolt™ card to the

PCIEX16(G4) slot.

21. Q-LEDs

The Q-LEDs check key components (CPU, DRAM, VGA, and booting devices) during the

motherboard booting process. If an error is found, the critical component’s LED stays lit up

until the problem is solved.

The Q-LEDs provide the most probable cause of an error code as a starting point for

troubleshooting. The actual cause may vary from case to case.

22. 8-pin Power Plug LED

The 8-pin Power Plug LED lights up to indicate that the 8-pin power plug is not connected.

PIN 1

FORCE_PWR

CIO_PLUG_EVENT

SLP_S3#

SLP_S5#

GND

RTD3_SW

I2C_SCL

I2C_SDA

I2C_IRQ#

RTD3_POWER_EN

S_SLP_S0#_IDLE

PERST_N

WAKE#

TB_HEADER

ProArt B760-CREATOR

1-8

1.2.2 Rear panel connectors

811109 9 12 13

51 6 7432

1. DisplayPort. This port is for a DisplayPort-compatible device.

2. USB 2.0 ports. These Universal Serial Bus (USB) ports are for USB 2.0 devices.

3. Ethernet port. This port allows Gigabit connection to a Local Area Network (LAN)

through a network hub. Refer to the table below for the Ethernet port LED indications.

Ethernet port LED indications

Speed LED

Status Description

OFF 10 Mbps connection

ORANGE 100 Mbps connection

GREEN 1 Gbps connection

Activity Link LED

Status Description

OFF No link

ORANGE Linked

BLINKING Data activity

ACT/LINK

LED SPEED

LED

LAN port

4. 2.5G Ethernet port. This port allows 2.5Gbps Ethernet connection to a Local Area

Network (LAN) through a network hub. Refer to the table one the next page for the

Ethernet port LED indications.

Realtek 2.5G Ethernet port LED indications

Speed LED

Status Description

OFF No link

GREEN 2.5 Gbps connection

ORANGE 1 Gbps / 100 Mbps /

10 Mbps connection

Activity Link LED

Status Description

OFF No link

GREEN Linked

BLINKING Data activity

ACT/LINK

LED SPEED

LED

LAN port

5. Center / Subwoofer port (orange). This port connects the center/subwoofer speakers.

6. Rear Speaker Out port (black). This port connects the rear speakers in a 4 channel,

5.1 channel, or 7.1 channel audio conguration.

7. Line In port (light blue). This port connects the tape, CD, DVD player, or other audio

sources.

Chapter 1: Product Introduction

1-9

8. HDMI™ port. This port is for a High-Denition Multimedia Interface (HDMI™)

connector, and is HDCP compliant allowing playback of HD DVD, Blu-ray, and other

protected content.

9. USB 3.2 Gen 1 (up to 5Gbps) ports. These Universal Serial Bus (USB) ports connect

to USB 3.2 Gen 1 devices.

10. USB 3.2 Gen 2 (up to 10Gbps) port (USB Type-C®). This Universal Serial Bus (USB)

port connects to a USB 3.2 Gen 2 Type-C® device.

11. Optical S/PDIF out port. This port allows you to connect your PC to amplied

speakers, headphones, or Sony/Phillips Digital Interconnect Format (S/PDIF) compliant

devices.

12. Microphone port (pink). This port connects a microphone.

13. Line Out port (lime). This port connects a headphone or a speaker. In 4-channel,

5.1-channel, and 7.1-channel congurations, the function of this port becomes Front

Speaker Out.

Refer to the audio conguration table below for the function of the audio ports in 2, 4, 5.1,

or 7.1-channel conguration.

Audio 2, 4, 5.1 or 7.1-channel configuration

Port 2-channel 4-channel 5.1-channel 7.1-channel

Light Blue

(Rear panel) - - - Side Speaker Out

Lime

(Rear panel) Front Speaker Out Front Speaker Out Front Speaker Out Front Speaker Out

Pink

(Rear panel) - - - -

Black

(Rear panel) - Rear Speaker Out Rear Speaker Out Rear Speaker Out

Orange

(Rear panel) - - Center/

Subwoofer

Center/

Subwoofer

ProArt B760-CREATOR

1-10

1.3 Central Processing Unit (CPU)

This motherboard comes with a LGA1700 socket designed for 13th Gen

Intel® Core™ &12th Gen Intel® Core™, Pentium® Gold and Celeron®

Processors.

Unplug all power cables before installing the CPU.

• Ensure that you install the correct CPU designed for LGA1700 socket only. DO NOT

install a CPU designed for LGA1155, LGA1156, LGA1151, and LGA1200 sockets on

the LGA1700 socket.

• ASUS will not cover damages resulting from incorrect CPU installation/removal,

incorrect CPU orientation/placement, or other damages resulting from negligence by

the user.

Installing the CPU

Take caution when lifting the load

lever, ensure to hold onto the load

lever when releasing the load

lever. Letting go of the load lever

immediately after releasing it may

cause the load lever to spring

back and cause damage to your

motherboard.

Chapter 1: Product Introduction

Pagina se încarcă ...

Asus ProArt B760-CREATOR Manual de utilizare

Marca: Asus

Model: ProArt B760-CREATOR

Categorie: Plăci de bază

Tip: Manual de utilizare

Descărcați PDF

raport

în alte limbi

italiano: Asus ProArt B760-CREATOR Manuale utente

Lucrări conexe

Alte documente

Edimax EN-9320TX-E V2 10 Gigabit Ethernet PCI Express Server Adapter Ghid de instalare