Ubiquiti EdgePoint EP-R8 Quick Start Quide

Intelligent WISP Control

with FiberProtect

™

Model: EP-R8

Introduction

Thank you for purchasing the Ubiquiti Networks® EdgePoint

™

Router. This Quick Start Guide is designed to guide you through

installation and includes the warranty terms.

Package Contents

EdgePoint Router Wall-Mount

Bracket

Metal Straps

(Qty. 2)

Cable Sleeve

Intelligent WISP Control

with FiberProtect

™

Model: EP-R8

Gigabit PoE (54V, 1.5A) with

Mounting Bracket

Power Cord Quick Start

Guide

Installation Requirements

• 7 mm socket wrench

• S2 hex wrench

• Ground wire – min. 10 AWG (5 mm

2

) and max. length: 1m. Asa

safety precaution, ground the EdgePoint to a grounded mast,

pole, tower, or grounding bar.

• Shielded Category 5 (or above) cabling should be used for all

wired Ethernet connections and should be grounded through

the AC ground of the PoE.

• We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial-grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit: www.ubnt.com/toughcable

TERMS OF USE: Shielded Ethernet cable and earth grounding must be used as conditions of product

warranty. TOUGHCable

™

is designed for outdoor installations. It is the customer’s responsibility to

follow local country regulations, including operation within legal frequency channels, output power,

and Dynamic Frequency Selection (DFS) requirements.

1

Introduction

Hardware Overview

Bottom Panel Button

Reset

Button

Description

Reset

There are two methods to reset the EP-R8 to

factory defaults:

Runtime Reset (Recommended)

The EP-R8 should be running after bootup is

complete. Press and hold the Reset button

for about 10seconds until the eth7 or SFP2

LED starts flashing and then becomes solidly

lit (the SFP 2 LED is used if there is an SFP

module connected to the SFP 2 port). After

a few seconds, the LED will turn off, and the

EP-R8 will automatically reboot.

Power-on Reset

1. Disconnect power from the EP-R8.

2. Press and hold the Reset button while

connecting power to the EP-R8. Keep

holding the button until the eth7 or SFP 2

LED starts flashing and then stops flashing

after a few seconds (the SFP 2 LED is used

if there is an SFP module connected to the

SFP 2 port).

2

EdgePoint EP-R8 Quick Start Guide

Bottom Panel Console Port

Console

Interface Description

Console

RJ45 serial console port for Command

Line Interface (CLI) management. Use an

RJ45-to-DB9, serial console cable, also known

as a rollover cable, to connect the Console

port to your computer. (If your computer does

not have a DB9 port, then you will also need

a DB9 adapter.) Then configure the following

settings as needed:

• Baud rate 115200

• Data bits 8

• Parity NONE

• Stop bits 1

• Flow control NONE

Note: Remove the protective plug from the Console port

before use.

3

Hardware Overview

Power Options

Either the VDC or PoE input type is used at any one time. If both

are connected, only the input type with the highest voltage will be

used; the other can be used as a backup.

Both PoE inputs can be used at the same time. If there is a voltage

difference, the higher-voltage source will be used first. The voltage

from the initial source will drop as the load increases. When the

voltage drops to the same level as the lower-voltage source, then

the lower-voltage source will also start providing power.

Power Input Options

• 54VDC, 6A

• 54V, 1.5A on eth0 (PoE In)

• 54V, 1.5A on PoE In

Power Output Options

• EdgePoint (required)

• Passive 54/24V, 4-Pair PoE on

eth1-eth2

• Passive 24V, 2-Pair PoE on

eth3-eth7

The number of devices that can be powered depends on the

power consumption of the specific devices. Example: If you use

54VDC, 1.5A, then you have 81W. If the EdgePoint uses 40W, then

you have 41W for PoE output. Check product specifications for the

power consumption values to use in your calculations.

Bottom Panel DC Input

VDC

Interface Description

VDC In

Terminal block connector uses auto-polarity

detection and accepts +42 to +56VDC, 6A

input (including the Ubiquiti EdgePower

™

,

model EP-54V-150W) to power the EdgePoint

and passive PoE output. -48V is NOT supported.

4

EdgePoint EP-R8 Quick Start Guide

Bottom Panel RJ45 Ports

PoE In

eth0

eth1-2

eth3-7

Interface

Description

PoE In

Accepts 54V, 1.5A PoE input from a secondary

PoE adapter (not included) to power the

EdgePoint and passive PoE output.

PoE In / eth0

Accepts data and 54V, 1.5A PoE input from

the included Gigabit PoE Adapter to power the

EdgePoint and passive PoE output.

eth1-2

(54/24V

PoE Out)

RJ45 ports support 10/100/1000 Ethernet

connections and passive 54/24V, 4-pair PoE

output for airFiber® devices.

eth3-7

(24V PoE Out)

RJ45 ports support 10/100/1000 Ethernet

connections and passive 24V, 2-pair PoE

output for airMAX® devices.

RJ45 port eth6 or eth7 is active only if the

corresponding SFP port is empty.

Note: The USB port is reserved for future use.

5

Hardware Overview

Bottom Panel SFP Ports

SFP 1-2

Interface

Description

SFP 1-2

SFP ports are hot-swappable and support

100 Mbps or Gigabit fiber SFP modules. If an

SFP module is plugged in, then the SFP port

is active, and the corresponding RJ45 port is

deactivated.

Note: For extreme temperatures, please use industrial-grade

fiber SFP modules.

Front Panel LEDs

LED State Status

eth0

Speed/

Link/Act

Off No Link

Amber

10/100Mbps Link

Flashing Indicates Activity

Green

1000Mbps (1 Gbps) Link

Flashing Indicates Activity

6

EdgePoint EP-R8 Quick Start Guide

LED State Status

power

Green EdgePoint Powered On

eth1-2

Speed/

Link/Act

Off No Link

Amber

10/100Mbps Link

Flashing Indicates Activity

Green

1000Mbps (1 Gbps) Link

Flashing Indicates Activity

PoE

Output

Off No PoE

Amber 54V, 4-Pair Passive

Green 24V, 4-Pair Passive

eth3-7

Speed/

Link/Act

Off No Link

Amber

10/100Mbps Link

Flashing Indicates Activity

Green

1000Mbps (1 Gbps) Link

Flashing Indicates Activity

PoE

Output

Off No PoE

Green 24V, 2-Pair Passive

SFP 1-2

Speed/

Link/Act

Off No Link

Amber

100Mbps Link

Flashing Indicates Activity

Green

1000Mbps (1 Gbps) Link

Flashing Indicates Activity

7

Hardware Overview

Back Panel

PicoStation Slot

Lanyard Loop

Pole-Mount

Bracket

Ground

Bonding Point

Lanyard Loop Used for temporary support during installation.

PicoStation®M2HP Slot Used for mounting an optional

PicoStationM2HP (not included) to the back of the EdgePoint. (You

can use the PicoStationM2HP for wireless management of the

EdgePoint.)

Pole-Mount Bracket Used for pole-mounting or in combination

with the included Wall-Mount Bracket for wall-mounting.

Ground Bonding Point Used to secure a ground wire (not

included).

8

EdgePoint EP-R8 Quick Start Guide

Attaching the Cable Sleeve

3. Insert and rotate the coupling to attach the Cable Sleeve to the

EdgePoint.

Note: You have two options for using a 2.0-inch NPT

(National Pipe Thread) male conduit (not included):

• Use the conduit instead of the CableSleeve.

• Use the conduit to extend the CableSleeve.

9

Attaching the Cable Sleeve

Hardware Installation

You can mount the EdgePoint on a pole or to a wall. Follow the

appropriate instructions for your installation method.

Pole-Mounting

1. Open the two Metal Straps and feed them through the

mounting slots on the back of the EdgePoint.

2. Wrap the Metal Straps around the pole. Use a 7 mm socket

wrench to turn the screws clockwise and securely fasten the

straps to the pole.

3. Proceed to the Grounding the EdgePoint section.

10

EdgePoint EP-R8 Quick Start Guide

Wall-Mounting

1. Use M8 screws and anchors (not included) to attach the

Wall-Mount Bracket to the wall.

Note: The Wall-Mount Bracket must attach directly to a

stud or other structurally stablesurface.

Tab

Pointing

Up

2. Insert the tabs of the Wall-Mount Bracket into the slots of the

EdgePoint. Slide the EdgePoint down.

11

Hardware Installation

3. Use two M8x10 screws (not included) to attach the EdgePoint

to the Wall-Mount Bracket.

12

EdgePoint EP-R8 Quick Start Guide

Grounding the EdgePoint

Note: The ground wire should be as short as possible and

no longer than one meter in length.

1. Remove the nut from the Ground Bonding Point located on the

back of the EdgePoint.

2. Attach a ground wire (min. 10 AWG or 5 mm

2

) to the lug and

replace the nut to secure the wire.

3. Secure the other end of the ground wire to a grounded mast,

pole, tower, or grounding bar.

13

Grounding the EdgePoint

Connecting Ethernet

1. Use an S2 hex wrench to loosen the Screw and remove the port

cover from the EdgePoint.

Screw

2. Feed the Ethernet cables through the Cable Sleeve and connect

them to ports in this range: eth0-eth7.

Note: PoE is disabled by default.

14

EdgePoint EP-R8 Quick Start Guide

3. You can create a strain relief for any Ethernet cable by feeding

a cable tie (not included) through the tie slot under the cable.

Then wrap the cable tie around the cable and tighten.

4. Connect the other ends of the Ethernet cables to your network

devices.

15

Connecting Ethernet

Using SFP Ports (Optional)

For information about compatible fiber SFP modules, visit:

community.ubnt.com/edgemax

To use an SFP port:

1. Plug a compatible fiber module into the SFP port.

Note: The corresponding RJ45 port will be deactivated.

2. Feed the fiber optic cable through the Cable Sleeve, and

remove the cable jacket from the fiber optic cable.

1000Mbps SM/SC 20KM DDM

Tx1550nm/Rx1310nm

SN: 1 308 2617 9

EF- 100 0M- 20K M- 15

50

16

EdgePoint EP-R8 Quick Start Guide

3. Separate the fiber optic strands and spool them around the

strain relief reels in the direction of the arrows. Then connect a

fiber optic strand to the fiber module.

50

1000Mbps SM/SC 20KM DDM

Tx1550nm/Rx1310nm

SN: 1 308 2617 9

EF- 100 0M- 20K M- 15

50

4. To finish the strain relief:

a. Feed a cable tie (not included) through the tie slot near the

cable opening.

b. Feed an additional cable tie (not included) through the tie

slots at the bottom of the strain relief reels.

50

1000Mbps SM/SC 20KM DDM

Tx1550nm/Rx1310nm

SN: 1 308 2617 9

EF- 100 0M- 20K M- 15

50

17

Using SFP Ports (Optional)

Connecting to Power

Either the +42 to +56VDC input or PoE input is used at any one

time. If both input types are connected, only the input type

with the highest voltage will be used; the other can be used as a

backup. Follow the appropriate instructions for your installation.

WARNING: -48V is NOT supported.

Connecting to the VDC Input

1. Wire one end of the DC power cable to the VDC terminal block,

which uses auto-polarity detection.

2. Replace the port cover and use an S2 hex wrench to tighten

the Screw and secure the port cover.

Screw

3. Wire the other end of the cable to a DC power supply.

4. Connect the DC power supply to its power source.

18

EdgePoint EP-R8 Quick Start Guide

Pagina se încarcă ...

Ubiquiti EdgePoint EP-R8 Quick Start Quide

Acest manual este potrivit și pentru

Ubiquiti EdgePoint EP-R8 Quick Start Quide

în alte limbi

Lucrări conexe

Alte documente