Ubiquiti edgepoint r6 Ghid de inițiere rapidă

Marca: Ubiquiti

Model: edgepoint r6

Tip: Ghid de inițiere rapidă

Intelligent WISP Control

with FiberProtect

™

Model: EP-R6

Introduction

Thank you for purchasing the Ubiquiti Networks® EdgePoint

™

Router. This Quick Start Guide is designed to guide you through

installation and includes the warranty terms.

Package Contents

EdgePoint Router Metal Strap Gigabit PoE (24V, 1.25A) with

Mounting Bracket

Intelligent WISP Control

with FiberProtect

™

Model: EP-R6

Power Cord Quick Start Guide

Installation Requirements

• Phillips screwdriver

• 7 mm socket wrench

• Ground wire – min. 10 AWG (5 mm

) and max. length: 1m. Asa

safety precaution, ground the EdgePoint to a grounded mast,

pole, tower, or grounding bar.

• Shielded Category 5 (or above) cabling should be used for all

wired Ethernet connections and should be grounded through

the AC ground of the PoE.

• We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial‑grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit: www.ubnt.com/toughcable

warranty. TOUGHCable

™

is designed for outdoor installations. It is the customer’s responsibility to

follow local country regulations, including operation within legal frequency channels, output power,

and Dynamic Frequency Selection (DFS) requirements.

Introduction

Hardware Overview

Ports Panel

Ground

Bonding Point

Reset

Interface

Description

Ground

Bonding Point

Used to secure a ground wire (not included).

Reset

There are two methods to reset the EP‑R6 to

factory defaults:

• Runtime reset (recommended) The

EP‑R6 should be running after bootup is

complete. Press and hold the Reset button

for about 10seconds until the eth4 LED

starts flashing and then becomes solidly lit.

After a few seconds, the LED will turn off,

and the EP‑R6 will automatically reboot.

• Power-on reset Disconnect power from

the EP‑R6. Press and hold the Reset button

while connecting power to the EP‑R6. Keep

holding the button until the eth4 LED starts

flashing and then stops flashing after a few

seconds.

EdgePoint EP‑R6 Quick Start Guide

Power Options

Either the VDC input or PoE input is used at any one time. If both

input types are connected, only the input type with the highest

voltage will be used; the other can be used as a backup. Any of the

input options can power any of the output options.

Power Input Options

• 24VDC, 3A

• 24V, 1.4A on eth0 (PoE In)

Power Output Options

• EdgePoint (required)

• Passive 24V, 2‑Pair PoE on

eth0-eth4

The number of devices that can be powered depends on the

power consumption of the specific devices. For example, if

you provide 24VDC, 1.25A, then you have 30W of power. If the

EdgePoint uses 7W (Max. Power Consumption), then you have

23W available for passive PoE output. Please check product

specifications for the power consumption values to use in your

calculations.

DC Input

VDC

Interface Description

VDC In

Terminal block connector accepts 24VDC, 3A

input to power the EdgePoint and passive

PoEoutput.

Hardware Overview

Ports

PoE In / eth0 eth1-4

eth5 / SFP

Interface

Description

PoE In/eth0

(24V PoE Out)

The RJ45 port supports 10/100/1000 Ethernet

connections and has PoE input or output

functionality:

• PoE Input Accepts 24V, 1.4A PoE input to

power the EdgePoint and PoE output.

• PoE Output You can configure the port for

24V 2‑pair PoE output.

Do NOT configure port eth0 in PoE output

mode if you are using it as a PoE input power

source.

eth1‑4

(24V PoE Out)

RJ45 ports support 10/100/1000 Ethernet

connections and passive 24V, 2‑pair PoE

output for airMAX® devices.

eth5/SFP

The SFP port is hot‑swappable and supports

100 Mbps or Gigabit fiber SFP modules.

Note: For extreme temperatures, please use industrial‑grade

fiber SFP modules.

EdgePoint EP‑R6 Quick Start Guide

Front Panel LEDs

LED State Status

power

Green EdgePoint Powered On

eth0‑eth4

Speed/

Link/Act

Off No Link

Green

10/100/1000Mbps (1 Gbps) Link

Flashing Indicates Activity

PoE

Output

Off No PoE

Green 24V Passive

eth5/SFP

Speed/

Link/Act

Off No Link

Green

100/1000Mbps (1 Gbps) Link

Flashing Indicates Activity

Hardware Overview

Hardware Installation

Pole Mounting

1. Open the Metal Strap and feed it through the mounting slots

on the back of the EdgePoint.

2. Wrap the Metal Strap around the pole. Use a 7 mm socket

wrench to turn the screw clockwise and securely fasten the

strap to the pole.

3. Proceed to the Grounding the EdgePoint section.

EdgePoint EP‑R6 Quick Start Guide

Removing the Port Cover

1. Press down and remove the port cover from the EdgePoint.

2. Depending on which cables will be connected, remove the

corresponding cable feed plugs from the port cover.

Hardware Installation

Grounding the EdgePoint

Note: The ground wire should be as short as possible and

no longer than one meter in length.

1. Remove the grounding screw and secure a ground wire (not

included) to the Ground Bonding Point.

2. Secure the other end of the ground wire to a grounded mast,

pole, tower, or grounding bar.

EdgePoint EP‑R6 Quick Start Guide

Connecting Ethernet

1. Connect the Ethernet cables to ports in this range: eth0‑eth4.

Note: PoE is disabled by default.

2. You can create a strain relief for any Ethernet cable by feeding

a cable tie (not included) through the tie slot under the cable.

Then wrap the cable tie around the cable and tighten.

3. Connect the other ends of the Ethernet cables to your

networkdevices.

Connecting Ethernet

Using the SFP Port (Optional)

For information about compatible fiber SFP modules, visit:

community.ubnt.com/edgemax

To use an SFP port:

1. Plug a compatible fiber module into the SFP port.

2. Connect a fiber optic strand to the fiber module.

EdgePoint EP‑R6 Quick Start Guide

3. Create a strain relief by feeding a cable tie (not included)

through the tie slot under the cable. Then wrap the cable tie

around the cable and tighten.

Using the SFP Port (Optional)

Connecting to Power

Either the VDC input or PoE input is used at any one time. If both

input types are connected, only the input type with the highest

voltage will be used; the other can be used as a backup. Follow the

appropriate instructions for your installation:

Connecting to the 24VDC Input

1. Wire one end of the DC power cable to the VDC terminal block.

2. When you are finished, replace the port cover.

Optional: You can use an M4x6 set screw (not included) to

secure the port cover.

3. Wire the other end of the cable to a DC power supply. (Wiring

will depend on your device.)

4. Connect the DC power supply to its power source.

EdgePoint EP‑R6 Quick Start Guide

Connecting Power Using PoE

Note: Do NOT configure port eth0 in PoE output mode if you

are using it as a PoE input power source.

1. Connect an Ethernet cable to the PoE In / eth0 port of the

EdgePoint.

2. Connect the other end of the Ethernet cable to the POE port

on the Gigabit PoE adapter.

3. Connect an Ethernet cable from the LAN to the LAN port on

the Gigabit PoE adapter.

4. Connect the Power Cord to the Gigabit PoE adapter. Then plug

the Power Cord into a power outlet.

Connecting to Power

5. When you are finished, replace the port cover.

Optional: You can use an M4x6 set screw (not included) to

secure the port cover.

Mounting the Gigabit PoE Adapter (Optional)

1. Remove the PoE Mounting Bracket from the adapter, place the

bracket at the desired location, and mark the two holes.

2. Pre‑drill the holes if necessary, and secure the bracket using

two fasteners (not included).

3. Align the slots on the adapter with the tabs on the PoE

Mounting Bracket, and then slide the adapter down.

EdgePoint EP‑R6 Quick Start Guide

Accessing the EdgeOS® Configuration Interface

Note: Ensure that your host system is connected to the

Gigabit PoE adapter or local network of the EdgePoint.

1. Configure the Ethernet adapter on your host system with a

static IP address on the 192.168.1.x subnet.

2. Launch your web browser. Type https://192.168.1.1 in the

address field. Press enter (PC) or return (Mac).

3. The login screen will appear. Enter ubnt in the Username

and Password fields. Read the Ubiquiti License Agreement,

and check the box next to I agree to the terms of this License

Agreement to accept it. Click Login.

The EdgeOS Configuration Interface will appear, allowing you to

customize your settings as needed. You can click the Wizards tab

to access the Setup Wizard. For information on PoE configuration,

refer to the Configuring PoE Settings section.

Accessing the EdgeOS® Configuration Interface

Configuring PoE Settings

WARNING: Before activating 24V passive PoE, ensure

that the connected device supports PoE and the

suppliedvoltage.

1. Go to Actions > PoE for the interface you want to configure.

2. Select 24V from the PoE drop‑down menu.

Note: If the PoE screen states that PoE is not supported,

then there is insufficient power. You will need to increase

the power input to the EdgePoint.

3. ClickSave.

For more information, refer to the EdgeOS User Guide, which is

available at documentation.ubnt.com/edgemax

EdgePoint EP‑R6 Quick Start Guide

Specifications

EP‑R6

Dimensions 188.6 x 177.1 x 49.8 mm (7.43 x 6.97 x 1.96")

Weight 605 g (1.33 lb)

Max. Power Consumption 7W (Excludes PoE Output)

Power Input (1) DC Terminal Block or (1) RJ45 (eth0)

(Self‑Correcting Polarity Protection on DC

Terminal Block Only,

Diode ORed Protection on All Power Inputs)

Power Supply Min. 24V / 0.3A (Excludes PoE Output Power)

VDC Input 24V, 3A

Passive PoE Input (1) 24V / 1.4A, 4‑Pair (+1, 2, 4, 5; ‑3, 6, 7, 8)

Passive PoE, eth0

(Do NOT congure eth0 in PoE output mode

if you are using a PoE input power source.)

Passive PoE Output (5) 24V / 0.7A, 2‑Pair (+4, 5; ‑7, 8)

Passive PoE, eth0 to eth4

Power Monitoring (1) DC Terminal Block, Input Power

(1) RJ45, eth0, Input Power

Supported Voltage Range 26 to 16VDC

Button Reset

LEDs

System

eth0 to eth4

eth5/SFP

Power

Speed/Link/Activity, PoE

Speed/Link/Activity

Ports

Data Ports (5) 10/100/1000 RJ45 Ports

(1) 1 Gbps SFP Port

Processor Dual‑Core 880 MHz, MIPS1004Kc with

Hardware Acceleration for Packet Processing

System Memory 256 MB DDR3‑1600 RAM

Code Storage 256 MB NAND

Certications CE, FCC, IC

Pole/Wall Mount Yes

Operating Temperature ‑40 to 65° C (‑40 to 149° F)

Operating Humidity 10 ‑ 90% Noncondensing

Specifications

Safety Notices

1. Read, follow, and keep these instructions.

2. Heed all warnings.

3. Only use attachments/accessories specified by the manufacturer.

WARNING: Do not use this product in location that can be

submerged by water.

WARNING: Avoid using this product during an electrical

storm. There may be a remote risk of electric shock from

lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current

requirements indicated on the manufacturer’s label. Connection to a different

power source than those specified may result in improper operation, damage to

the equipment or pose a fire hazard if the limitations are not followed.

2. There are no operator serviceable parts inside this equipment. Service should be

provided only by a qualified service technician.

3. This equipment is provided with a detachable power cord which has an integral

safety ground wire intended for connection to a grounded safety outlet.

a. Do not substitute the power cord with one that is not the provided approved

type. Never use an adapter plug to connect to a 2‑wire outlet as this will

defeat the continuity of the grounding wire.

b. The equipment requires the use of the ground wire as a part of the safety

certification, modification or misuse can provide a shock hazard that can

result in serious injury or death.

c. Contact a qualified electrician or the manufacturer if there are questions

about the installation prior to connecting the equipment.

d. Protective earthing is provided by Listed AC adapter. Building installation

shall provide appropriate short‑circuit backup protection.

e. Protective bonding must be installed in accordance with local national wiring

rules and regulations.

EdgePoint EP‑R6 Quick Start Guide

Pagina se încarcă ...

Ubiquiti edgepoint r6 Ghid de inițiere rapidă

Marca: Ubiquiti

Model: edgepoint r6

Tip: Ghid de inițiere rapidă

Descărcați PDF

raport

în alte limbi

English: Ubiquiti edgepoint r6 Quick start guide
italiano: Ubiquiti edgepoint r6 Guida Rapida

Ubiquiti edgepoint r6 Ghid de inițiere rapidă

Ubiquiti edgepoint r6 Ghid de inițiere rapidă

în alte limbi

Lucrări conexe

Alte documente