Ubiquiti Networks AF-24 Manualul utilizatorului

Marca: Ubiquiti Networks

Model: AF-24

Tip: Manualul utilizatorului

Acest manual este potrivit și pentru

airFiber AF-24

24 GHz Point to Point

1.4+ Gbps Radio

Model: AF-24

Introduction

Thank you for purchasing the Ubiquiti Networks® airFiber® 24GHz

Point-to-Point Radio. This Quick Start Guide is designed to guide

you through installation, show you how to access the airFiber

Configuration Interface, and explain how to set up an airFiber link.

This Quick Start Guide also includes the warranty terms and is for

use with the model AF-24.

Package Contents

airFiber AF-24 Pole Mount Bracket Pole Clamps

(Qty. 2)

Cable Ties

(Qty. 3)

Carriage Bolts

(M10x150, Qty. 4)

Flat Washers

(M10, Qty. 4)

Split Lock Washers

(M10, Qty. 4)

Hex Nuts

(M10, Qty. 4)

24 GHz Point to Point

1.4+ Gbps Radio

Model: AF-24

GigE PoE Adapter

(50V, 1.2A)

Power Cord airFiber AF-24

Quick Start Guide

earth grounding must be used as conditions of product warranty. TOUGHCable

™

is designed for

outdoor installations. It is the customer’s responsibility to follow local country regulations, including

operation within legal frequency channels, output power, and Dynamic Frequency Selection (DFS)

requirements.

Introduction

Hardware Overview

Side

Alignment Bracket

Elevation

Adjustment

Azimuth

Adjustment

Ground

Bonding Point

Lock Bolts

airFiber® AF-24 Quick Start Guide

Back

Lock Bolts

Azimuth

Adjustment

Lock Bolts

Cover Lock

Elevation

Adjustment

Port Cover

Hardware Overview

Interfaces

RESET DATA AUX CONFIGLED Display

Interface Description

RESET

To reset to factory defaults, press and hold the Reset

button for more than five seconds while the unit is

already powered on.

DATA 10/100/1000 Mbps port handles all user traffic.

AUX Port for audio tone aiming.

LED Display

Digital display used for power, status, and mode

information.

CONFIG

10/100 Mbps, secured port for configuration. By

default, this is the only port that can monitor,

configure, and/or update firmware.

LEDs

Link/Act

Speed

GPS

Modulation Link/Act

SpeedRX Power

Master/Slave

RF Link Status

airFiber® AF-24 Quick Start Guide

LED State Status

DATA

Speed

Off 10/100 Mbps

On 1000 Mbps

Link/Act

Off No Ethernet Link

On Ethernet Link Established

Random Flashing Ethernet Activity

AUX

GPS

Off No GPS Synchronization

On Operational (Strong Signal)

Normal Flash* Operational (Weak Signal)

Modulation

Off ¼x or 1x (QPSK SISO)

Short Flash* 2x (QPSK MIMO)

Normal Flash* 4x (16QAM MIMO)

Long Flash* 6x (64QAM MIMO)

LED Display

RX Power

(-dBm)

Number Decodable RX Signal

Flashing Number Undecodable RX Signal

Overload Condition

Master/

Slave

Off Slave Mode

On Master Mode

RF Link

Status

Off RF Off

Short Flash* Syncing

Normal Flash* Beaconing

Long Flash* Registering

On Operational

CONFIG

Speed

Off 10 Mbps

On 100 Mbps

Link/Act

Off No Ethernet Link

On Ethernet Link Established

Random Flashing Ethernet Activity

* Short Flash (1:3 on/off cycle)

Normal Flash (1:1 on/off cycle)

Long Flash (3:1 on/off cycle)

Hardware Overview

Installation Requirements

• 17 mm wrench

• 13 mm socket wrench or driver

• Clear line of sight between airFiber radios

• Clear view of the sky for proper GPS operation

• Mounting location with < 0.5° displacement due to twist and

sway under wind loading

• Mounting point:

• At least 1 meter below the highest point on the structure

• For tower installations, at least 3 meters below the top of the

tower

• Ground wires – min. 8 AWG (10 mm

) and max. length: 1 meter.

As a safety precaution, ground the airFiber radios to grounded

masts, poles, towers, or grounding bars.

WARNING: Failure to properly ground your airFiber

units will void your warranty.

• (Recommended) 2 Outdoor GigE PoE surge protectors

Note: For guidelines about grounding and lightning

protection, follow your local electrical regulatory codes.

• Outdoor, shielded Category 5e (or above) cabling and shielded

RJ-45 connectors should be used for all wired Ethernet

connections. Category 6 is required for installations with long

cable runs (up to 100 m).

We recommend that you protect your networks from the

most brutal environments and devastating ESD attacks with

industrial-grade shielded Ethernet cable and shielded RJ-45

connectors from Ubiquiti Networks. For more details, visit

www.ubnt.com/toughcable

Installation Overview

We recommend that you configure your paired airFiber radios

before mounting. Below is an overview of the installation with

specific details on the following pages:

• Connect Power over Ethernet to the DATA port, and connect an

Ethernet cable between your computer and the CONFIG port.

• Configure device settings in the airFiber Configuration Interface.

airFiber® AF-24 Quick Start Guide

• Once configuration is complete, disconnect the cables to move

the airFiber radios.

• Reconnect at the site.

• After you have mounted the airFiber radios, establish and

optimize the RF link.

Connecting Power over Ethernet

1. Turn the Cover Lock to the Unlocked icon. Slide the Port Cover

down to remove it.

2. Connect an Ethernet cable to the DATA port.

Connecting Power over Ethernet

3. Connect the other end of the Ethernet cable from the DATA

port to the Ethernet port labeled POE on the GigE PoE Adapter.

4. Connect the Power Cord to the power port on the GigE PoE

Adapter. Connect the other end of the Power Cord to a power

source.

airFiber® AF-24 Quick Start Guide

airFiber

Configuration

The instructions in this section explain how to access the airFiber

Configuration Interface and configure the following settings:

• Wireless Mode Configure one airFiber AF-24 as the Master and

the other as the Slave.

• Duplex The airFiber AF-24 supports both half-duplex and

full-duplex operation. Half-duplex operation provides more

frequency planning options at the cost of higher latency

and throughput. Full-duplex operation provides the highest

throughput and lowest latency; however, you have fewer

frequency management options.

- Half Duplex (default) The TX and RX Frequencies can be the

same or different to suit local interference.

SlaveMaster

Frequency A

Half-Duplex Diagram

- Full Duplex The TX and RX Frequencies should be different.

SlaveMaster

Frequency A

Frequency B

Full-Duplex Diagram

• TX and RX Frequencies The TX Frequency on the Master must

match the RX Frequency on the Slave, and vice versa.

airFiber Configuration

1. Connect an Ethernet cable from your computer to the CONFIG

port on the airFiber AF-24.

2. Configure the Ethernet adapter on your computer with a

static IP address on the 192.168.1.x subnet (for example,

192.168.1.100).

3. Launch your web browser. Type http://192.168.1.20 in the

address field and press enter (PC) or return (Mac).

4. The login screen will appear. Enter ubnt in the Username and

Password fields. Select your Country and Language. You must

agree to the Terms of Use to use the product. Click Login.

Note: U.S. product versions are locked to the U.S. Country

Code to ensure compliance with FCC regulations.

airFiber® AF-24 Quick Start Guide

5. Click the Wireless tab.

6. Enter the Basic Wireless Settings:

a. For one airFiber AF-24, select Master from the Wireless Mode

drop-down. For the other airFiber AF-24, keep the default,

Slave.

b. Enter a name in the Link Name field. This should be the

same on both the Master and the Slave.

c. For the Duplex drop-down:

- Half Duplex The default mode. The TX and RX Frequencies

can be the same or different to suit local interference.

- Full Duplex The TX and RX Frequencies should be different.

d. Select a TX Frequency. This must match the RX Frequency on

your other airFiber AF-24.

e. Select a RX Frequency. This must match the TX Frequency of

your other airFiber AF-24.

f. If needed, change the Output Power, Maximum Modulation

Rate, and/or RX Gain settings.

airFiber Configuration

7. Configure the Wireless Security:

a. Select the AES Key Type, HEX or ASCII.

b. For the Key field:

- HEX Enter 16 bytes (eight, 16-bit HEX values: 0-9, A-F, or

a-f). You can omit zeroes and use colons, similar to the

IPv6 format.

Note: The airFiber Configuration Interface supports

IPv6 formats excluding dotted quad and "::"

(double-colon) notation.

- ASCII Enter a combination of alphanumeric characters (0-9,

A-Z, or a-z).

8. Click Change and then click Apply.

9. In-Band Management is enabled by default, so each airFiber

radio must have a unique IP Address. (If the airFiber radios use

the same IP Address, then you may lose access to the airFiber

radios via the DATA ports.) To change the networksettings:

a. Click the Network tab.

b. Change the IP Address, Netmask, and other settings to make

them compatible with your network.

c. Click Change and then click Apply.

Repeat the instructions in the airFiber Configuration section on

your other airFiber radio. After you have configured the airFiber

radios, disconnect them and move them to your installation site.

airFiber® AF-24 Quick Start Guide

Hardware Installation

To install the airFiber AF-24:

1. Insert the four Carriage Bolts into the Pole Mount Bracket.

2. Attach the Pole Mount Bracket to a pole.

Note: The mounting assembly can accommodate a

Ø 51 - 101 mm (2.0" - 4.0") pole.

a. Orient the Pole Mount Bracket around the pole so it is aimed

in the direction of the other airFiber AF-24.

b. Insert the Carriage Bolts into the Pole Clamps.

c. Secure the clamps with the Flat Washers, Split Lock Washers,

and Hex Nuts.

Note orientation of slots

Aim towards link

Hardware Installation

3. Loosen, but do NOT remove the eight Lock Bolts located on the

Alignment Bracket.

4. Ensure that there is a 6 mm gap between the head of each

M8x14 Serrated Flange Screw and the Alignment Bracket.

6 mm

airFiber® AF-24 Quick Start Guide

5. Lift the airFiber AF-24 and align the four M8x14 Serrated Flange

Screws with the slots on the Pole Mount Bracket. Seat the screws

in the slots. Securely tighten the screws.

WARNING: To prevent injury, ensure that all four screws

are seated and fully tightened.

Hardware Installation

6. Attach a ground wire:

a. Remove the nut from the Ground Bonding Point.

b. Attach a ground wire (min. 8 AWG or 10 mm

) to the lug and

replace the nut to secure the wire.

c. Secure the other end of the ground wire to a grounded

mast, pole, tower, or grounding bar.

WARNING: Failure to properly ground your airFiber

units will void your warranty.

Note: The ground wire should be as short as possible

and no longer than one meter in length.

airFiber® AF-24 Quick Start Guide

Connecting Ethernet

1. Turn the Cover Lock to the Unlocked icon. Slide the Port Cover

down to remove it.

2. Connect a TOUGHCable or other outdoor, shielded CAT5e/6

cable to the DATA port.

3. Create a strain relief for the Ethernet cable by feeding a

CableTie through the tie slot under the cable. Then wrap the

Cable Tie around the cable and tighten.

Connecting Ethernet

4. Connect the other end of the Ethernet cable from the DATA

port to the Ethernet port labeled POE on the GigE PoE Adapter.

5. Connect an Ethernet cable from your network to the Ethernet

port labeled LAN on the GigE PoE Adapter.

6. Connect the Power Cord to the power port on the GigE PoE

Adapter. Connect the other end of the Power Cord to a power

source.

Note: For added protection, we recommend installing

two GigE PoE surge protectors. Install the first surge

protector within one meter of the airFiber DATA port, and

install the second surge protector at the ingress point of

the location housing the wired network equipment.

airFiber® AF-24 Quick Start Guide

Pagina se încarcă ...

Ubiquiti Networks AF-24 Manualul utilizatorului

Marca: Ubiquiti Networks

Model: AF-24

Tip: Manualul utilizatorului

Acest manual este potrivit și pentru

airFiber AF-24

Descărcați PDF

raport

în alte limbi

English: Ubiquiti Networks AF-24 User guide

Ubiquiti Networks AF-24 Manualul utilizatorului

Acest manual este potrivit și pentru

Ubiquiti Networks AF-24 Manualul utilizatorului

în alte limbi

Lucrări conexe

Alte documente