Scheppach PL75 Original Instruction Manual

Marca: Scheppach

Model: PL75

Categorie: Unelte electrice

Tip: Original Instruction Manual

Art.No.

5901804906

Version

5901804852

07/07/2015

PL75

AUS

Plunge Cut Saw

Original instruction manual

2 І 16

8 8

3 І 16

2-3 mm

B C

4 І 16

5 І 16

Explanation of symbol on the product

AUS

Caution - Read the operating instructions to reduce the risk of inquiry

AUS

Wear ear-muffs!

AUS

Wear a breathing mask!

AUS

Wear safety goggles!

AUS

Protection class II

2. Device description Fig.1a, 1b

1. Handle/hand grip

2. Front handle

3. Plunge-cut trigger

4. On/off switch

5. Base plate

6. Adjustment screw for depth of cut

7. Scale for depth of cut

8. Mitre adjustment screw

9. Mitre square

10. 90-degree adjustment screw

11. Saw blade

12. Suction nozzle

13. Adjustment screw for guide rail

14. Shaft locking mechanism

15. Splitter guard

3. General information

• After unpacking, check all parts for possible trans-

portation damages. In the event of complaints, in-

form the supplier immediately. Any complaints made

after this time will not be accepted.

• The shipment is to be checked for completeness

upon receipt.

• Read through the manual carefully in order to make

yourself familiar in dealing with the device before

using it for the rst time.

• Only use original equipment regarding accessories,

as well as consumable items and spare parts. Spare

parts can be obtained from your specialized dealer.

When ordering, please specify our part numbers, as

well as type and construction year of the device.

4. Proper use

CE tested machines meet all valid EC machine gui-

delines as well as all relevent guidelines for each

machine.

• The machine must only be used in technically per-

fect con dition in accordance with its designated use

and the in structions set out in the operating manual,

and only by safety-conscious persons who are fully

aware of the risks involved in oerating the machine.

Any functional dis orders, especially those affecting

the safety of the machine, sholud terefore be rectied

immediately.

• Any other use exceeds authorization. The manufactu-

rer is not responsible for any damages resulting from

un authorized use; risk is the sole responsibility of the

operator.

• The safety, work and maintenance instructions of the

manufacturer as well as the technical data given in

the calibrations and dimensions must be adhered to.

• Relevant accident prevention regulations and other,

gene rally recognized safety-technical rules must also

be adhered to.

1. Introduction

DESIGNED & ENGINEERED:

scheppach

Fabrikation von Holzbearbeitungsmaschinen GmbH

Günzburger Straße 69

D-89335 Ichenhausen

Made in China

DEAR CUSTOMER,

We wish you much joy and success in working with your

new appliance.

NOTE:

According to the applicable product liability laws, the

manufacturer of the device does not assume liability

for damages to the product or damages caused by the

product that occurs due to:

• Improper handling,

• Non-compliance of the operating instructions,

• Repairs by third parties, not by authorized service

technicians,

• Installation and replacement of non-original spare

parts,

• Application other than specied,

• A breakdown of the electrical system that occurs

due to the non-compliance of the electric regulations

and VDE regulations 0100, DIN 57113 / VDE0113.

We recommend:

Read through the complete text in the operating in-

structions before installing and commissioning the

device. The operating instructions are intended to

help the user to become familiar with the machine

and take advantage of its application possibilities in

accordance with the recommendations. The operating

instructions contain important information on how to

operate the machine safely, professionally and eco-

nomically, how to avoid danger, costly repairs, reduce

downtimes and how to increase reliability and service

life of the machine.

In addition to the safety regulations in the operating

instructions, you have to meet the applicable regulati-

ons that apply for the operation of the machine in your

country. Keep the operating instructions package with

the machine at all times and store it in a plastic cover

to protect it from dirt and moisture. Read the instruc-

tion manual each time before operating the machi-

ne and carefully follow its information. The machine

can only be operated by persons who were instructed

concerning the operation of the machine and who are

informed about the associated dangers. The minimum

age requirement must be complied with.

7 І 16

3) Personal safety

a) Be attentive, watch what you are doing and use the

power tool sensibly. Do not use power tools when you

are tired or under the inuence of drugs, alcohol or

medicines. One moment of inattention while using a

power tool can result in serious injury.

b) Wear personal protective equipment and always wear

protective glasses. Wearing personal protective equip-

ment, such as a dust mask, slip-free safety shoes, pro-

tective headwear or ear protection, depending on the

type and use of a power tool reduces the risk of injury.

c) Avoid unintentional start-ups. Make sure that the po-

wer tool is shut off before it is connected to the power

supply, or is carried. If you have your nger on the

switch of the tool while carrying it, or have the tool

turned on, or connected to a power supply, this beha-

viour can lead to accidents.

d) Remove the adjustment aides or the spanners be-

fore turning on the power tool. A tool or wrench that

is located in a rotating part of the machine, can lead

to injuries.

e) Avoid abnormal posture. Make sure that the operator

is standing rmly and can maintain balance. This al-

lows the operator to maintain control over the power

tool in unexpected situations.

f) Wear appropriate clothing. Do not wear loose clothing

or jewellery. Keep hair, clothing and gloves away from

the moving parts. Loose clothing, jewellery or long hair

can get caught in the moving parts.

g) If dust vacuums or catching systems can be installed

on the tool, make sure that these are correctly con-

nected and assembled. The use of a dust exhaust unit

can reduce hazards caused by dust.

4) Use and treatment of the power tool

a) Do not overtax the tool. Use the appropriate tool for

the work that is to be done. With the correct power

tool, you can work better and more safely.

b) Do not use a power tool where the switch is defec-

tive. A power tool that cannot be turned on and off is

dangerous and must be repaired.

c) Disconnect the plug from the wall outlet before you

make adjustments to the tool, change parts or put the

tool away. This precaution prevents inadvertent start-

ups of the tool.

d) Store power tools that are not in use out of reach of

children. Do not let anyone use the tool who does not

have experience with it, or who has not read these in-

structions. Power tools can be dangerous when they

are used by inexperienced people.

e) Take good care of your power tools. Make sure that

movable parts function properly and do not jam, see

that parts which inuence the use of the machine are

not broken or damaged. Repair damaged parts befo-

re operating the tool. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting edges sharp and clean. Properly main-

tained cutting tools with sharp cutting edges jam less

often and are easier to control.

g) Use power tools, accessories, and equipment accor-

ding to these instructions. Taking into account the wor-

• The machine may only be used, maintained, and ope-

rated by persons familiar with it and instructed in its

operation and procedures. Arbitrary alterations to the

machine release the manufacturer from all responsi-

bility for any resulting damages.

• The machine may only be used with original accesso-

ries and tools made by the manufacturer.

• The machine may not be operated with sanding belts.

5. General safety instructions for pow-

er tools

• WARNING Read all warnings and instructions. Fai-

lure to apply all warnings and instructions can lead to

electrical shock, re and/or serious injury.

• Keep all warnings and instructions handy for fu-

ture consultation.

• The term “power tool” used in the warnings refers to

power tools that are connected to a source of electrical

energy (with an electrical cable)

1) Workplace safety

a) Keep your working area clean and well lit. Cluttered

or dimly lit workspaces can lead to accidents.

b) Do not operate power tools in areas where explosions

could take place, or in which ammable liquids, gases

or dust are present. Power tools can create sparks,

which can cause dust or fumes to ignite.

c) Keep children and bystanders away from the power

tool when it is being used. Distractions could cause

you to lose control over the equipment.

2) Electrical safety

a) The terminal plug of the tool must t into the outlet.

The plug may not be modied in any way. Do not use

an adaptor plug together with grounded power tools.

The original plugs and the appropriate outlets reduce

the risk of an electrical shock.

b) Avoid contact with grounded surfaces, such as pipes,

radiators, stoves and refrigerators. There is an increa-

sed risk of electrical shock, if your body is grounded.

c) Keep power tools away from rain or wet conditions.

Penetration of water into the power tool increases the

risk of electrical shock.

d) Do not use the cable for any purpose other than that

for which it was made. Do not use it to carry the tool,

hang it up, or to pull the plug out of the outlet. Keep

the cable away from heat, oil, sharp corners or parts

of the equipment that move. Damaged or entangled

cords increase the risk of electrical shock.

e) When operating the power tool outdoors, only use

extension cords that are suitable for outdoor use. The

use of an appropriate extension cord reduces the risk

of an electrical shock.

f) If the power tool must be used in a damp environment,

use a residual current protective device. The use of

such a device reduces the risk of electrical shock.

the saw back in the direction of the operator.

• If the saw blade twists in the saw groove or is incor-

rectly positioned, the teeth at the rear side of the saw

blade edge catch in the surface of the work piece. The

saw then moves out of the saw groove and springs

back in the direction of the operator.

• A kickback results from an incorrect or faulty use of the

saw. It can be prevented, as will be described in the

following, by appropriate cautionary measures.

a) Hold onto the saw with both hands and position your

arms so that they can absorb any energy from a kick-

back. Always keep to the side of the saw blade, and

never bring it into line with your body. In the case of

a kickback, the circular saw can jump backwards, but

with adequate caution the operator can deal with the

energy of the kickback.

b) If the saw blade jams or you want to interrupt your

work, then turn the saw off and keep the work piece

still until the saw blade comes to a full stop. Never

try to remove the saw from the work piece or pull it

out when the saw blade is moving since then a kick-

back can occur. Find out the cause of the jam and

remove it.

c) If you want to start up a saw that is in the work piece,

centre the saw blade in the sawed groove and check

that the saw blade teeth are not caught in the work pi-

ece. If the saw blade is jammed, it can jump out of the

work piece or cause a kick back when it is started up.

d) Support larger work pieces in order to reduce the risk

of a kick back due to a saw blade jam. The weight of

larger work pieces can cause them to bend. Large pi-

eces must be supported on both sides, both near the

sawing slot as well as on the edges.

e) Do not use dull or damaged saw blades. Saw blades

with dull or misaligned teeth increase the friction, in

the sawing slot, cause saw blade jams and kickbacks.

f) Before you start sawing, tighten the adjustments for

the cut depth and angles. If you change settings while

sawing, the saw blade can jam and a kickback is the

result.

g) Be particularly careful when making “inserted cuts”

in walls that already exist or other areas where you

cannot see what is behind the surface. When the saw

blade is inserted into the wall it can be blocked by hid-

den objects and cause a kick back.

8. Safety instructions for inserted circu-

lar saw use

a) Each time before you use the saw, make sure that

the protective covering closes. Do not use the saw if

the protective covering cannot move freely and does

not close immediately. Never clip or tie the protective

covering in an opened position. If the saw should ac-

cidentally fall to the ground, the protective covering

can get bent. Make sure that the protective covering

can move freely and does not touch the saw blade or

other parts in all cutting positions.

b) Check the condition and function of the spring for

king conditions and the work being performed.

The use of power tools other than those intended for

the tool itself can lead to dangerous situations.

5) Service

a) Only let qualied service personnel repair your tool

and always use original replacement parts. This gua-

rantees that the power tool remains safe to use.

6. Safety instructions for all saws

a) DANGER: Do not put your hands in the sawing area or

on the saw blade. Keep your second hand on the extra

handle of the motor housing. If both hands are holding

the saw, neither can be injured by the saw blade.

One-handed operation is permitted only in conjunction

with rail and anti-tilt.

b) Do not put your hands under the work piece. The pro-

tective cap cannot protect your hands from the blade

when they are under the work piece.

c) Adjust the cutting depth to the thickness of the work

piece. Less than one complete sawing tooth should

be visible under the work piece.

d) Never hold the work piece that is to be sawn in your

hand or over your leg. Make sure that the work piece

has a stable balance. It is important that the work pi-

ece is held securely, in order to minimize the danger

of contact of a body part with the saw, loss of control

over the saw, or jamming of the blade.

e) Hold the equipment on the insulated handles, when

you undertake work in which the tool being used could

come into contact with hidden electrical wires, or its

own cable. Contact with a live power source can elec-

trify the metal parts of the tool and lead to an electri-

cal shock.

f) When making a long cut, always use a stop chock

or a straightedge. This improves the accuracy of the

cut and reduces the chance that the saw blade jams.

g) Always use the correct size of saw blades and ma-

ke sure they have the right locating bore (e.g. Star

shaped or round). Saw blades that do not t the as-

sembly of the saw do not run correctly and cause loss

of control.

h) Never use damaged or incorrect saw blade shims

or screws.

The saw blade shims and screws are designed espe-

cially for your saw, for optimal performance and ope-

rating safety.

7. Additional safety instructions for all

saws

Causes and prevention of kickbacks:

• A kickback is a sudden reaction due to a caught, jam-

med or incorrectly adjusted saw blade, which leads

to the saw rearing up in an uncontrolled manner and

moving out of the work piece towards the operator.

• If a saw blade catches or jams in the sawing edge that

closes behind it, it is blocked and motor’s drive pushes

9 І 16

FURTHER SPECIAL SAFETY INSTRUCTIONS FOR

CIRCULAR SAWS

a) Only use the recommended saw blades which corre-

spond to EN 847-1.

b) Do not use sanding belts.

c) Only use the manufacturer’s original saw.

Do not use any saw blades which do not correspond

to the characteristics described in these operating ins-

tructions. Saw blades may not be brought to a stop by

pressure on the machine from the side.

Make sure that the saw blade is tightly assembled and

turns in the correct direction.

10. Special Safety Instructions

Safety instructions for circular saws

- Hold the equipment on the insulated handles, when

you undertake work in which the tool being used could

come into contact with hidden electrical wires, or its

own cable. Contact with a live power source can elec-

trify the metal parts of the tool and lead to an electri-

cal shock.

11. Technical data

Dimensions

L x W x H mm

420x300x235

Saw blade ø mm / number of

teeth

210 / 36

Thickness of saw blade 1,6

Idling speed n

4500

Mitre square 0°-45°

Depth of cut 90° mm 75

Depth of cut 45° mm 55

Weightkg 6,9

Motor V/Hz 230 / 50

Input W 1600

Protection class II

Sound pressure level

95 dB(A),

: 3 dB (A)

Sound power level

106 dB(A),

: 3 dB (A)

Typical weighted vibrations

5,72 m/s

K: 1,5 m/s

Subject to technical modications!

Warning: Noise can have adverse health effects. Should

the noise level increase above 85 dB(A), you must wear

ear protection. Should the electrical supply not be opti-

mal, then the current can drop for a short time when the

machine is turned on. This can inuence other equip-

ment (for example, the blinking of a lamp). Should the

electrical capacity have a Zmax < 0.27, such disturban-

the protective covering. Have the saw repaired before

use if the protective covering and spring do not work

perfectly. Damaged parts, sticky residuals or piles of

saw dust can interfere with the working of the lower

protective cover.

c) When making an “inserted cut” that does not descri-

be a right angle, make sure that the saw is guarded

against slipping to the side. Slippage can lead to a

saw blade jam and a kickback.

d) Do not put the saw on the workbench or the oor wit-

hout making sure that the protective cover is over the

saw blade. An unprotected, running saw blade can

move the saw against the cutting direction and saw

what is in the way. Check the delay time of the saw.

9. Additional safety instructions for all

sawing with a wedge

a) Use the right wedge for the saw blade that is in use.

The wedge must be thicker than the thickness of the

steel blade but thinner than the width of the teeth.

b) Adjust the wedge as described in the operating inst-

ructions. Incorrect thickness, position or direction can

be the reason that the wedge does not effectively pre-

vent a kickback.

c) Always use a wedge, except when making an inserted

cut. Reassemble the wedge after an inserted cut. The

wedge is in the way when making an inserted cut and

can cause a kickback.

d) In order for the wedge to be effective, it must be in the

sawing gap. For short cuts, a wedge does not work to

prevent kickbacks.

e) Never run the saw with a bent wedge. Even the smal-

lest defect can slow down the closing of the protec-

tive cover.

INSTRUCTIONS FOR ALL SAWS

• Do not use a sanding belt.

• Make sure that the wedge is adjusted so that the di-

stance to the sprocket ring of the saw blade is not

more than 5 mm and that the sprocket ring does not

stick out more than 5 mm above the lower edge of

the wedge.

• Make sure that the dust catching mechanism is cor-

rectly installed, as is described in this manual.

• Wear breathing protection.

• Only those saw blades recommended in the manual

should be used.

• Always wear ear protection.

• Replace the saw blades as described in this manual.

• The maximum cut depth is 75 mm.

If the electrical cable of this tool is damaged it must be

replaced by the manufacturer or the customer service

department or a similarly qualied specialist in order to

avoid dangers.

10 І 16

lowing electrical specications of the machine stated on

the motor.

15. ADJUSTING

Caution: Prior to carrying out one of the following ad-

justment steps, switch the machine off and unplug the

mains plug.

Cutting depth adjustment, Fig. 2

The cutting depth can be adjusted from 0 to 75 mm.

Unfasten the cutting depth adjustment screw (6) and set

the required depth using the scale (7) and retighten the

screw.

The dimentions on the rail shows the cutting depth wit-

hout rail.

Mitre settings, Fig. 3

The mitre square can be set from 0° to 45°.

Unfasten the mitre adjustment screws (8) on both sides,

set the desired mitre square on the scale (9) and retigh-

ten both screws.

Saw blade replacement, Fig. 4, 5, 6

Caution: Before you are going to make the saw bla-

de change, switch off the machine and unplug the

power cord.

1 Press the plunge trigger (3), bring the saw blade into

the blade-change position (Adjustment screw for depth

of cut shall be adjusted to 25mm) and insert the hex

wrench into the blade locking screw (17).

2 Press on the shaft lock (13) and rotate the saw blade

(10) until the lock clicks into place.

3 Hold down the locking shaft (13) and open the blade

locking screw (17) counter clockwise, while keeping

the blade in the blade-changing position.

4 Remove the outer ange (16) and the saw blade (10).

(Caution: risk of injuries, wear protective gloves)

5 Insert the new blade and ange.

6 Screw in and tighten the saw blade locking screw while

keeping the shaft locking mechanism pressed again.

7 Set the plunge saw to its original position.

Adjusting the splitting wedge, Fig. 7

Adjust the distance between saw blade and splitting

wedge after a saw blade replacement, or whenever ne-

cessary.

Put the saw in the same position as you do when repla-

cing a saw blade.

Unfasten the adjustment screw (18) using an Allen key

and set the splitting wedge 2-3 mm higher than the saw

blade, then retighten the adjustment screw.

Justieren Sie den Abstand Sägeblatt (10) zum Spaltkeil

(19) nach dem Sägeblattwechsel, oder wenn es erfor-

derlich ist.

ces are not to be expected. (Should you have difculties,

please consult your local dealer.)

12. Remaining hazards

The machine has been built using modern technolo-

gy in accor dance with recognized safety rules. Some

remaining hazards, how ever, may still exist.

• The use of incorrect or damaged mains cables can

lead to injuries caused by electricity.

• Even when all safety measures are taken, some re-

maining hazards which are not yet evident may still

be present.

• Remaining hazards can be minimized by following the

instructions in „Safety Precautions“, „Proper Use“ and

in the entire operating manual.

• Do not force the machine unnecessarily: excessive

cutt ing pressure may lead to rapid deterioration of the

blade and a decrease in performance in terms of nish

and cutting precision.

• When cutting aluminium and plastics always use the

app ro priate clamps: all workpieces must be clamped

down rmly.

• Avoid accidental starts: do not press the start button

while inserting the plug into the socket.

• Always use the tools recommended in this manual

to obtain the best results from your plunge cut saw.

• Always keep hands away from the work area when

the ma chine is running; before performing tasks of

any kind release the main switch button located on the

handgrip, thus disconnecting the machine.

13. Suitable use

To cut:

• Hard and soft, domestic and exotic wood both longitu-

dinally and transversally and with appropriate adjust-

ments (specic blade and clamps);

Unsuitable use

Do not cut:

• Ferrous materials, steel and cast iron or any other ma-

terial not mentioned above and in particular foodstuffs.

14. Start-up

Observe the safety notes in the operating instruc-

tions before operating the machine.

ELECTRICAL CONNECTIONS

Check that the electrical system to which the machine

is connected is earthed in compliance with current sa-

fety regulations and that the current socket is in perfect

condition.

The electrical system must be tted with a magnetother-

mal protective device to safeguard all conductors from

short circuits and overload.

The selection of this device should be in line with the fol-

11 І 16

This physical injuries or damage to the machine can

be avoided.

Sawing with dust suction

Connect the suction hose to the exhaust nozzle - Ø 38

mm (12).

Splitter protection Fig.1b

The splinter protection (15) improved signicantly at

0° cuts are the quality of the cut edge of the sawed-off

workpiece part on the upward side.

• Place the machine on the workpiece and guide rail.

• Splitter protection (15) down until it rests on the

workpiece and tighten the knob.

• Splitter protection (15) sawing. At the rst use of

Splitteschutzes (15) we sawed this to generate an

exact stop area.

17. Electrical connection

The installed electric motor is completely wired rea-

dy for operation.

The customer’s connection to the power supply sys-

tem, and any extension cables that may be used,

must conform with local regulations.

Important remark:

The motor is automatically switched off in the event of

an overload. The motor can be switched on again after a

cool ing down period that can vary.

Defective electrical connection cables

Electrical connection cables often suffer insulation dam-

age. Possible causes are:

• Pinch points when connection cables are run through

window or door gaps.

• Kinks resulting from incorrect attachment or laying of

the connection cable.

• Cuts resulting from running over the connecting cable.

• Insulation damage resulting from forcefully pulling out

of the wall socket.

• Cracks through aging of insulation.

Such defective electrical connection cables must not be

used as the insulation damage makes them extremely

hazardous.

Check electrical connection cables regularly for dama-

ge. Make sure the cable is disconnected from the mains

when checking.

Electrical connection cables must comply with the regu-

lations applicable in your country.

Single-phase motor

• The mains voltage must coincide with the voltage spe-

cied on the motor’s rating plate.

• Extension cables up to a length of 25 m must have a

cross-section of 1.5 mm2, and beyond 25 m at least

2.5 mm2.

• The connection to the mains must be protected with

a 16 A slow-acting fuse.

16. Operations

After having performed all the above procedures and

opera tions, you may begin cutting.

ATTENTION: Always keep hands away from the cutting

area and do not try to approach it when the machine is

running.

Switching the product on/off, Fig. 1

To switch the plunge-cut saw on, press the on/off switch

(4). To switch off, release the on/off switch (4).

Operating and holding the plunge-cut saw, Fig. 8

1 Secure the work piece so that it cannot get displaced

or moved while sawing.

2 Only move the saw forwards.

3 Grip the saw tightly with both hands ensuring that one

hand is placed on the main handle and the other on

the front handle.

4 When using a guide rail, it must be fastened with screw

clamps.

5 Make sure the power cable is not placed in the sawing

direction.

Sawing

1 Place the front part of the machine onto the work piece.

2 Switch the machine on using the on/off switch (4).

3 Press the plunge-cut trigger (3).

4 Push the saw downwards to reach the sawing depth.

5 Push the saw forward evenly.

6 After nishing the sawing cut, switch the machine off

and move the saw blade upwards.

Plunge-cuts, Fig. 9

1 Place the saw onto the work piece.

2 Place the cutting indicator with the rear arrow (A) on

the marked plunge-cut position.

3 Switch the machine on and push the saw downwards

until you reach the set cutting depth.

4 Move the saw forwards until the cutting indication (C)

has reached the marked point.

5 After completion of the plunge-cut, move the saw blade

upwards and switch the saw off.

Cutting with rails (otional)

1 Place the machine in the guide rails. can be readjusted

using the hex driver included in the delivery, when

there is the risk of the adjusting screws releasing by

themselves.

2 Turn on the machine by pressing the on/off switch (4).

3 Press the dip trigger (3).

4 Press the saw downwards to reach the sawing depth.

During rst use the rubber lip is sawn off and thus

splitter protection is guaranteed up to the saw blade.

5 Push the saw uniformly forwards.

6 Turn off the machine and tilt the saw blade to the top

when the saw cutting is complete.

Tilt Protection (Fig.10)

Put the rail saws with a the supplied anti-tilt (20). This

prevents the machine from tilting sideways when tilting.

12 І 16

REGULAR MAINTENANCE

The regular maintenance decribed above and in the

para graph below can be carried out by unskilled person-

nel.

• Do not oil the plunge cut saw, cause cutting must be

carried out in dry conditions; all rotating parts are self-

lubricating.

• During maintenance, wear protective gear if possible

(accident-prevention goggles and gloves).

• Remove cuttings when necessary both from the cut-

ting area, work surfaces and support bases.

Use of an aspirator or brush is recommended.

ATTENTION: Do not use compressed air jets!

Regularly check blade conditions: if difculties should

arise during cutting, have it sharpened by skilled per-

sonnel or replace it if necessary.

ASSISTENCE

When in need of skilled personnel for special mainte-

nance, or for repairs, both during and following the gu-

arantee pe riod, always apply to authorized centres for

assistance or directly to the manufacturer if there is no

authorized centre in your area.

Only a qualied electrician is permitted to connect the

machine and complete repairs on its electrical equip-

ment.

In the event of enquiries please specify the following da-

ta:

• Motor manufacturer

• Type of current of the motor

• Data recorded on the machine’s rating plate

• Data recorded on the switch’s rating plate

18. Maintenance

If specialist personnel must be brought in for extra-

ordinary ser vice or repairs during the warranty peri-

od and thereafter, please contact a service provider

recommended by us or con tact the manufacturer di-

rectly.

• Overhauls, maintenance work, cleaning, as well as the

eli mi nation of any malfunctions must only be underta-

ken af ter turning off the motor.

• All protective and safety equipment must be reins-

talled immediately upon completion of any repair or

maintenance work.

19. Trouble shooting

Problem Possible Cause Help

The motor does not run. Faulty motor, power supply cable or plug. Burned

out fuses.

Have the machine checked by skilled

personnel. Do not try to repair the machine

yourselves as it may be dangerous. Check

the fuses and replace them if necessary.

The motor starts slowly

and does not reach running

speed.

Low power supply voltage. Damaged windings.

Burned out capacitor.

Ask for the Electricity Board to check the

voltage available. Have the machine motor

checked by skilled personnel. Have the ca-

pacitor replaced by skilled personnel.

Excessive motor noise. Damaged windings. Faulty motor. Have the motor checked by skilled person-

nel.

The motor does not reach

full power.

Overloaded circuit due to lighting, utilities or other

motors.

Do not use other utilities or motors on the

circuit to which the plunge cut saw is con-

nected.

Motor overheats easily Overload of the motor; inadequate cooling of the

motor

Prevent overloading the motor when cutting;

remove dust from the motor to ensure an

optimum cooling of the motor

Decrease in cutting power

when sawing

The saw blade is too small (sharpened too often) Re-adjust the end stop of the saw unit

The saw cut is rough or

wavy

The saw blade is dull; the tooth shape is not

suited to the thickness of the material

Re-sharpen the saw blade or use an appro-

priate saw blade

The work piece rips or

splinters

The cutting pressure is excessive or the saw

blade is not suited to the application

Use the correct saw blade

14 І 16

Garantie DE

Offensichtliche Mängel sind innerhalb von 8 Tagen nach Erhalt der Ware anzuzeigen, andern-

falls verliert der Käufer sämtliche Ansprüche wegen solcher Mängel. Wir leisten Garantie für

unsere Maschinen bei richtiger Behandlung auf die Dauer der gesetzlichen Gewährleistungsfrist

ab Übergabe in der Weise, dass wir jedes Maschinenteil, dass innerhalb dieser Zeit nachweisbar

in Folge Material- oder Fertigungsfehler unbrauchbar werden sollte, kostenlos ersetzen. Für

Teile, die wir nicht selbst herstellen, leisten wir nur insoweit Gewähr, als uns Gewährleistungsan-

sprüche gegen die Vorlieferanten zustehen. Die Kosten für das Einsetzen der neuen Teile trägt

der Käufer. Wandlungs- und Minderungsansprüche und sonstige Schadensersatzansprüche

sind ausgeschlossen.

Warranty GB

Apparent defects must be notied within 8 days from the receipt of the goods. Otherwise, the

buyerís rights of claim due to such defects are invalidated. We guarantee for our machines in

case of proper treatment for the time of the statutory warranty period from delivery in such a

way that we replace any machine part free of charge which provably becomes unusable due

to faulty material or defects of fabrication within such period of time. With respect to parts not

manufactured by us we only warrant insofar as we are entitled to warranty claims against the

upstream suppliers. The costs for the installation of the new parts shall be borne by the buyer.

The cancellation of sale or the reduction of purchase price as well as any other claims for dam-

ages shall be excluded.

Garantie FR

Les défauts visibles doivent être signalés au plus tard 8 jours après la réception de la marchan-

dise, sans quoi l’acheteur perd tout droit au dédommagement.

Nous garantissons nos machines, dans la mesure où elles sont utilisées de façon conforme,

pendant la durée légale de garantie à compter de la réception, sachant que nous remplaçons

gratuitement toute pièce de la machine devenue inutilisable du fait d’un défaut de matière ou

d’usinage durant cette période. Toutes les pièces que nous ne fabriquons pas nous-mêmes ne

sont garanties que si nous avons la possibilité d’un recours en garantie auprès des fournisseurs

respectifs. Les frais de main d’œuvre occasionnés par le remplacement des pièces sont à la

charge de l’acquéreur. Tous droits à rédhibition et toutes prétentions à une remise ainsi que tous

autres droits à dommages et intérêts sont exclus

Garanzia IT

Vizi evidenti vanno segnalati entro 8 giorni dalla ricezione della merce, altrimenti decadono tutti

i diritti dellíacquirente inerenti a vizi del genere. Appurato un impiego corretto da parte dellíacq-

uirente, garantiamo per le nostre macchine per tutto il periodo legale di garanzia a decorrere

dalla consegna in maniera tale che sostituiamo gratuitamente qualsiasi componente che entro

tale periodo presenti dei vizi di materiale o di fabbricazione tali da renderlo inutilizzabile. Per

componenti non fabbricati da noi garantiamo solo nella misura nella quale noi stessi possiamo

rivendicare diritti a garanzia nei confronti dei nostri fornitori. Le spese per il montaggio dei

componenti nuovi sono a carico dellíacquirente. Sono escluse pretese di risoluzione per vizi, di

riduzione o ulteriori pretese di risarcimento danni.

Garantie NL

Zichtbare gebreken moeten binnen de 8 dagen na ontvangst van de goederen worden gemeld,

zo niet verliest de verkoper elke aanspraak op grond van deze gebreken. Onze machines

worden geleverd met een garantie voor de duur van de wettelijke garantietermijn. Deze termijn

gaat in vanaf het moment dat de koper de machine ontvangt. De garantie houdt in dat wij elk

onderdeel van de machine dat binnen de garantietermijn aantoonbaar onbruikbaar wordt als

gevolg van materiaal- of productiefouten, kosteloos vervangen. De garantie vervalt echter bij

verkeerd gebruik of verkeerde behandeling van de machine. Voor onderdelen die wij niet zelf

produceren, geven wij enkel de garantie die wij zelf krijgen van de oorspronkelijke leverancier.

De kosten voor de montage van nieuwe onderdelen vallen ten laste van de koper. Eisen tot het

aanbrengen van veranderingen of het toestaan van een korting en overige schadeloosstellings-

claims zijn uitgesloten.

Garantía ES

Los defectos evidentes deberán ser noticados dentro de 8 días después de haber recibido la

mercancía, de lo contrario el comprador pierde todos los derechos sobre tales defectos. Ga-

rantizamos nuestras máquinas en caso de manipulación correcta durante el plazo de garantía

legal a partir de la entrega. Sustituiremos gratuitamente toda pieza de la máquina que dentro

de este plazo se torne inútil a causa de fallas de material o de fabricación. Las piezas que no

son fabricadas por nosotros mismos serán garantizadas hasta el punto que nos corresponda

garantía del suministrador anterior. Los costes por la colocación de piezas nuevas recaen sobre

el comprador. Están excluidos derechos por modicaciones, aminoraciones y otros derechos de

indemnización por daños y perjuicios.

Garantia PT

Para este aparelho concedemos garantia de 24 meses. A garantia cobre exclusivamente

defeitos de matérial ou de fabricação. Peças avariadas são substituidas gratuitamente. cabe ao

cliente efetuar a substituição. Assumimos a garantia unicamente de peças genuinas.

Não há direito à garantia no caso de: peças de desgaste, danos de transporte, danos causados

pelo manejo indevido ou pela desatenção as instruções de serviço, falhas da instalação elétrica

por inobservançia das normas relativas á electricidade. Além disso, a garantia só poderá ser

reinvidicada para aparelhos que não tenham sido consertados por lerceiros. O cartão de garan-

tia só vale em conexão com a fatura.

Garanti NO

Åpenbare mangler skal meldes innen 8 dager etter at varen er mottatt, ellers taper kunden

samtlige krav pga slik mangel. Vi gir garanti for at våre maskiner ved riktig behandling under

den rettslige garantitidens varighet, fra overlevering, på den måten at vi erstatter kostnads-

fritt hver maskindel, som innen denne tiden påviselig er ubrukbar som følge av material- eller

produksjonsfeil. For deler som vi ikke produserer selv, yter vi garanti kun i den utstrekning som

garantikrav mot underleverandør tilkommer oss. Kjøperen bærer kostnadene ved montering av

nye deler. Endrings- og verditapskrav og øvrige skadeerstatningskrav er utelukkede.

Takuu FI

Ilmeisistä puutteista tulee ilmoittaa kahdeksan päivän kuluessa tavaran vastaanottamisesta.

Muutoin ostaja ei voi vaatia korvausta ko. puutteista. Annamme takuun oikein käsitellyille

koneillemme lakisääteiseksi takuuajaksi tavaran luovutuksesta alkaen siten, että vaihdamme

korvauksetta minkä tahansa koneenosan, joka osoittautuu tämän ajan kuluessa käyttökelvot-

tomaksi raaka-aine- tai valmistusvirheestä johtuen. Osille, joita emme valmista itse, annamme

takuun vain mikäli osien toimittaja on antanut niistä takuun meille. Uusien osien asennuskus-

tannukset maksaa ostaja. Purku- ja vähennysvaatimukset ja muut vahingonkorvausvaatimukset

eivät tule kysymykseen.

Garanti

Med denna maskin följer en 24 månaders garanti. Garantin täcker endast material- och kon-

struktionsfel. Defekta delar ersätts utan omkostningar, men kunden står för installationen. Vår

garanti täcker endast orginal-delar. Anspråk på garanti öreligger inte för: garantin täcker ej,

transportskador, skador orsakade av felaktig behandling och då skötselföreskrifter inte beaktats.

Vidare kan garantikrav endast ställas för maskiner som inte har reparerats av tredje part.

Záruka SK

Zrejmé vady musia byť predstavené v priebehu 8 dni po obdržaní tovaru, ináč zákazník stratí

všetky nároky týkajúce sa takejto vady. Ponúkame záruku na naše aparáty, ktoré sú správne

používané počas zákonného termínu záruky tak, že bezplatne vymeníme každú časť aparátu,

ktorá sa v priebehu tohto času môže stať dokázateľne nefunkčnou dôsledkom materiálnej či

výrobnej vady. Na časti ktoré sami nevyrábame, poskytujeme záruku iba v rozsahu, v ktorom

nám prísluší nárok na záručné plněnie k subdodávateľovi. Za trovy týkajúce sa inštalácie novej

súčiastky je zodpovedný zákazník. Nárok na výmenu tovara, na zľavu a iné nároky na nahrade-

nie škody sú vylúčené.

Garancija SI

Očitne pomanjkljivosti je potrebno naznaniti 8 dni po prejemu blaga, v nasprotnem primeru

izgubi kupec vse pravice do garancije zaradi takšnih pomanjkljivosti. Za naše naprave dajemo

garancijo ob pravilni uporabi za čas zakonsko določenega roka garancije od predaje in sicer

na takšen način, da vsak del naprave brezplačno nadomestimo, za katerega bi se v tem roku

izkazalo, da je zaradi slabega materiala ali slabe izdelave neuporaben. Za dele, ki jih sami ne

izdelujemo, jamčimo samo toliko, kolikor zahteva garancija drugih podjetij. Stroški za vstavljanje

novih delov nosi kupec. Zahteve za spreminjanje in zmanjšanje ter ostale zahteve za nadomesti-

lo škode so izključene.

Szavatosság HU

A nyilvánvaló hibákat ki kell jelenteni számított 8 napon belül az áruk, különben a vevő elveszti

minden igényt az ilyen hibák. Kínálunk garanciát a gépeinket a megfelelő kezelés időtartamának

hallgatólagos garancia a szállítás időpontját oly módon, hogy cserélje ki minden egyes része ezen

idő alatt észlelhető a sorban anyag-vagy gyártási legyen hiábavaló, ingyen. Az alkatrészeket, hogy

nem termel magunkat, hogy csak olyan garanciát, hiszen jogosultak jótállási igények beszállítókkal

szemben. A költségek beillesztése az új részek a vevőnek. Átalakítása és csökkentése

követelések és egyéb kártérítési igények ki vannak zárva.

Garancija HR

Vidljive štete se moraju prijaviti u roku od 8 dana od primitka robe U suprotnom slučaju kupac

gubi pravo na reklamaciju. Mi jamčimo za naše strojeve u slučaju ispravnog postupanja tijekom

perioda zakonskog jamstva tako što zamijenjujemo besplatno bilo koji dio stroja koji dokazano

postane neupotrebljiv uslijed neispravnog materijala ili grešaka u proizvodnji u tom vremenskom

periodu Za dijelove koje mi nismo proizveli jamčimo samo ukoliko imamo pravo na reklamaciju

prema dobavljačima Troškove za ugradnju novih dijelova snosi kupac Molbe za smanjenjem

cijene kao i sve druge reklamacije zbog šteta su isključene.

Záruka CZ

Viditelné vady jsou poukazatelné během 8 dní od obdržení zboží, jinak ztrácí zákazník všechny

nároky týkající se takovýchto vad. Poskytujeme záruku na naše stroje, s kterými je správně

zacházeno, na dobu zákonnné záruční lhůty začínající od doručení tak, že bezplatně vyměníme

každou část stroje, která se během této doby může stát prokazatelně nepoužitelnou následkem

materiálové či výrobní vady. Na díly, které sami neopravujeme, poskytujeme záruku pouze v

rozsahu , v němž nám přísluší nárok na záruční plnění vůči subdodavateli . Náklady na instalaci

nového dílu nese zákazník. Nárok na výměnu zboží, na slevu a jiné nároky na odškodnění jsou

vyloučené.

Gwarancja PL

Wszelkie uszkodzenia muszą być zgłaszane w przeciągu 8 dni od daty otrzymania towaru, w

przeciwnym wypadku, prawo do reklamacji wygasa. Gwarantujemy, że w czasie trwania gwarancji

wymienimy wszelkie części maszyny, które okażą się niesprawne na skutek wad materiału z jakie-

go zostały wykonane lub błędów w produkcji bez dodatkowych opłat pod warunkiem, że maszyna

będzie obsługiwana zgodnie z zaleceniami. W odniesieniu do części nie produkowanych przez

nas, gwarancja obowiązuje tylko w przypadku naszych dostawców. Koszty instalacji nowych części

są ponoszone przez klienta. Odszkodowania wynikłe z uszkodzeń maszyny oraz redukcje ceny

zakupu maszyny w ramach reklamacji nie będą rozpatrywane.

Garanție RO

Defecte evidente trebuie să e raportate în termen de 8 zile de la primirea de bunuri, alel cumpărătorul

pierde toate cererile pentru asel de defecte. Oferim o garanție de pe mașinile noastre cu un tratament

adecvat pe durata unei garanții implicite de la data de livrare în așa fel încât vom înlocui ecare parte în acel

moment detectabil într-un rând în material sau manoperă ar  inul, gratuit. Pentru părțile care nu ne pro-

duc, vom face doar o asel de garanție, așa cum avem dreptul la pretenții de garanție împotriva furnizorilor.

Costurile pentru introducerea de piese noi la cumpărător. Conversie și reducerea creanțe și alte cererile de

despăgubire sunt excluse.

Garantii EE

Ilmselgetest vigadest tuleb teatada 8 päeva jooksul pärast kauba kättesaamist, vastasel juhul

kaotab ostja kõik õigused garantiile nimetatud vigade tõttu. Õige käsitsemise korral anname oma

masinatele garantii seadusega ettenähtud ajaks alates kauba üleandmisest nii, et vahetame

tasuta välja kõik masina osad, mis nimetatud aja jooksul peaks muutuma kasutuskõlbmatuks

materjali- või tootmisvea tõttu. Osade eest, mida me ise ei tooda, anname garantii vaid selles osas,

mis tarnija on meile garanteerinud. Uute osade paigaldamise kulud kannab ostja. Muutmis- ja

amortisatsiooninõuded ning muud kahjutasunõuded välistatakse.

Garantija LV

Acīmredzami defekti ir jāpaziņo 8 dienu laikā no preces saņemšanas. Pretējā gadījumā pircēja

tiesības pieprasīt atlīdzību par šādiem defektiem ir spēkā neesošas. Mēs dodam garantiju savām

iekārtām, ja pircējs pret tām atbilstoši izturas garantijas laikā. Mēs apņemamies bez maksas piegā-

dāt jebkuru rezerves daļu, kas iespējams kļuvusi nelietojama bojātu materiālu vai ražošanas defek-

tu dēļ šajā laika periodā. Attiecībā uz rezerves daļām, kuras nav mūsu ražotas, mēs garantējam

tikai gadījumā, ja mums ir garantija no saviem piegādātājiem. Jauno detaļu uzstādīšanas izmaksas

ir jāuzņemas pircējam. Pirkuma atcelšana vai pirkuma cenas samazināšana, kā arī jebkuras citas

prasības par bojājumu atlīdzināšanu netiek izskatītas.

Garantija LT

Dėl akivaizdžiai matomų defektų turi būti informuota per 8 dienas nuo įrenginio gavimo momento.

Kitu atveju pirkėjo teisė reikšti pretenziją dėl šių defektų yra negaliojanti. Savo įrenginiams mes

garantuojame įstatymo nustatytą pilną aptarnavimą garantinio laikotarpio metu, jei yra laikomasi

gamintojo-vartotojo susitarimo ir mes pažadame nemokamai pakeisti bet kurias mašinos dalis,

sugedusias dėl blogos medžiagos ar gamyklinio broko. Mes neatsakome už dalis, pagamintas ne

mūsų ir jūsų gautas iš kito tiekėjo. Naujų dalių montavimo kaštai yra pirkėjo atsakomybė. Pirkimo

nutraukimas ar pirkimo kainos sumažinimas, kaip ir bet kurios kitos pretenzijos dėl nuostolių nebus

patenkinamos.

Ábyrgð IS

Augljósar skemmdir verður að tilkynna innan 8 daga frá viðtöku vörunnar. Annars er réttur kau-

panda um bætur vegna slíka skemmda ógildur. Við ábyrgjumst, í tilfelli réttrar meðhöndlunar yr

lögbundið ábyrgðartímabil frá afhendingu, að við skiptum um hvern vélarhlut án kostnaðar sem

ónothæfur er vegna gallaðs efnis eða skemmda í framleiðslu innan ákveðins tímabils. Af því er

tekur til hluti sem ekki eru framleiddir af

okkur, ábyrgjumst við af því leiti aðeins að við eigum rétt á ábyrgðarkröfum gagnvart birgðasölum.

Kostnaður vegna uppsetningar á nýjum hlutum skal falla í skaut kaupanda. Ógilding sölu eða

afsláttur á kaupverði sem og aðrar kröfur vegna skemmda eru undanskildar.

Garanti TR

Apaçık kusurları malların alınmasından 8 gün içinde bildirilmesi gerekir, aksi takdirde alıcı bu

kusurları için tüm talepler kaybeder. Biz ücretsiz, yararsız olmalıdır malzeme veya işçilik üst üste

saptanabilir bu süre içinde her bir parça takmadan böyle bir şekilde teslim tarihinden itibaren zımni

garanti süresine uygun tedavi ile makinelerde bir garanti veriyoruz. Biz tedarikçiler karşı garanti

talepleri hakkı olarak kendimizi üretmek değil bu parça için, biz, sadece teminat olun. Alıcıya yeni

parçaların yerleştirilmesi için maliyetleri. Dönüşüm ve azaltma iddiaları ve diğer tazminat talepleri

dahil değildir.

гаранция BG

Очевидни недостатъци трябва да бъдат докладвани в рамките на 8 дни от получаването на

стоки, в противен случай купувачът губи всякакви претенции за такива дефекти. Предлагаме

гаранция на нашите машини с правилното лечение на срока на действие на косвена

гаранция от датата на доставка по такъв начин, че ние замени всяка част в рамките на

това време открива в един ред в материала или изработката трябва да бъде безполезно,

безплатно. За части, които ние не се произвеждат, ние правим само като гаранция, като

имаме право на гаранционни искове срещу доставчици. Разходите за вмъкване на нови

части на купувача. Преобразуване и намаляване вземания и други исковете за обезщетения,

са изключени.

Гарантия RU

Об очевидных дефектах необходимо уведомить в течение 8 дней после получения товара. В

ином случае все претензии покупателя по таким дефектам не принимаются. Мы предостав-

ляем гарантию на наши машины при условии правильного обращения с ними. Гарантия дей-

ствует с момента передачи машины в течение установленного законом гарантийного срока.

В течение этого времени мы гарантируем бесплатную замену любой части машины, если

они стали непригодны к использованию в результате доказуемых ошибок в применяемых

материалах или при изготовлении. На части машины, которые мы не изготавливаем сами,

мы предоставляем гарантии в той мере, насколько нас касаются рекламационные претензии

к изготовителям. Расходы по замене деталей несет покупатель. Претензии на расторжение

договора купли-продажи, штрафы и прочие требования о возмещении ущерба исключаются.

Garantie BE-VLG

Zichtbare gebreken moeten binnen 8 dagen na ontvangst van de goederen worden gemeld,

anders verliest de koper elk recht op aanspraak voor dergelijke gebreken. Bij een juiste

behandeling van onze machines en gedurende de wettelijke garantietermijn vanaf de aevering

bieden wij garantie door elk machineonderdeel, dat tijdens deze periode door materiaal- of

productiefouten onbruikbaar zou worden, gratis te vervangen. Voor onderdelen die wij niet zelf

produceren, bieden wij enkel garantie in de mate die de toeleveranciers ons bieden. De kosten

voor de plaatsing van de nieuwe onderdelen draagt de koper. Aanspraken voor wijzigingen,

waardevermindering en overige schadeloosstelling zijn uitgesloten.

scheppach Fabrikation von Holzbearbeitungsmaschinen GmbH | Günzburger Str. 69 |

D-89335 Ichenhausen | www.scheppach.com

Scheppach PL75 Original Instruction Manual

Marca: Scheppach

Model: PL75

Categorie: Unelte electrice

Tip: Original Instruction Manual

Descărcați PDF

raport

în alte limbi

English: Scheppach PL75

Lucrări conexe

Scheppach 4901402901 Manual de utilizare

Scheppach PL75 Original Instruction Manual

Scheppach PL75 Original Instruction Manual

în alte limbi

Lucrări conexe

Alte documente