Zero-Variable Outdoor Radio
Models: BM2-Ti, BM5-Ti
1
Introduction
Introduction
Thank you for purchasing the Bullet
™
M Titanium. This Quick Start
Guide is designed to guide you through the installation of the
Bullet M Titanium and show you how to access the configuration
interface. This Quick Start Guide is for use with the following
models:
Model Operating Frequency
Bullet M2 Titanium 2412 - 2462 MHz
Bullet M5 Titanium 5470 - 5825 MHz*
* Only 5725-5850 MHz supported in the USA
Package Contents
Models: BM2-Ti, BM5-Ti
Zero-Variable Outdoor
Radio
Bullet M
Titanium
N-Type Right
Angle Adapter
Quick Start Guide
24V 1A PoE Adapter Power Cord
2
Bullet™ M Titanium Quick Start Guide
Hardware Overview
N-Type Female
Connector
Bullet
™
M Titanium
Radio
Rubber
Washer
Cable
Gland Body
Compression
Nut
Ethernet Port
Compression
Seal
3
Hardware Installation
Hardware Installation
To install the Bullet M Titanium, perform the following steps:
1. Unscrew the Cable Gland Body and detach it from the Bullet M
Titanium Radio.
2. Unscrew the Compression Nut and remove the Compression
Seal from the Cable Gland Body.
4
Bullet™ M Titanium Quick Start Guide
3. Slide the Compression Nut over the Ethernet cable with the
threaded end facing the RJ-45 connector. Slip the Compression
Seal around the cable.
4. Feed the Ethernet cable through the Cable Gland Body and seat
the Compression Seal into the Cable Gland Body.
5. Connect the Ethernet cable to the port located on the bottom
of the Bullet M Titanium Radio.
5
Hardware Installation
6. Securely screw the Cable Gland Body into the Bullet M Titanium.
Tightly screw the cable gland so that the Rubber Washer seals
the bottom of the Bullet M Titanium.
7. Tightly screw on the Compression Nut. Ensure the rubber is
securely compressed and tightly sealed around the cable.
6
Bullet™ M Titanium Quick Start Guide
8. Connect the Bullet M Titanium to the antenna.
Note: The Bullet M Titanium should be mounted vertically
to reduce stress on the N-Type Connector. The N-Type Right
Angle Adapter may be used as needed.
9. Connect the other end of the Ethernet cable from the Bullet M
Titanium to the Ethernet port labeled POE on the PoE Adapter.
7
Hardware Installation
10. Connect an Ethernet cable from your LAN to the Ethernet port
labeled LAN on the PoE Adapter.
11. Connect the power cord to the power port on the PoE Adapter.
Connect the other end of the power cord to a power outlet.
The hardware installation of your Bullet M Titanium is complete.
Continue to the next section "Accessing the airOS Utility" to
configure the Bullet M Titanium.
8
Bullet™ M Titanium Quick Start Guide
Accessing the airOS Utility
1. Make sure that your host machine is connected to the LAN that
is connected to the Bullet™ M Titanium.
2. Configure the Ethernet adapter on your host system with a
static IP address on the 192.168.1.x subnet (e.g., 192.168.1.100).
3. Launch your Web browser. Type http://192.168.1.20 in the
address field and press enter (PC) or return (Mac).
4. The login screen will appear. Enter ubnt in the Username and
Password fields. Select your Country and Language. You must
agree to the Terms of Use to use the product. Click Login.
Note: U.S. product versions are locked to the U.S. Country
Code to ensure compliance with FCC regulations.
The airOS Interface will appear, allowing you to customize your
settings as needed.
Installer Compliance Responsibility
Devices must be professionally installed and it is the professional
installer's responsibility to make sure the devices are operated
within local country regulatory requirements.
9
Specifications
Specifications
Bullet™ M Titanium Specications
Dimensions 190 mm x 46 mm
Weight 196 g
Max. Power Consumption
M2 7 Watts
M5 6 Watts
Power Supply 24V, 1A PoE Supply Included
Power Method Passive PoE (Pairs 4, 5+; 7,8 return)
Certications CE, FCC, IC
Operating Temperature -40 to +80° C
Operating Frequency
M2 2402 - 2462 MHz
M5 5170 - 5875 MHz*
Networking Interface (1) 10/100 Ethernet Port
* Only 5725 - 5850 MHz supported in the USA
Safety Notices
1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories specified by the
manufacturer.
WARNING: Do not use this product in location that can
be submerged by water.
WARNING: Avoid using this product during an electrical
storm. There may be a remote risk of electric shock from
lightning.
10
Bullet™ M Titanium Quick Start Guide
Electrical Safety Information
1. Compliance is required with respect to voltage, frequency, and
current requirements indicated on the manufacturer’s label.
Connection to a different power source than those specified
may result in improper operation, damage to the equipment or
pose a fire hazard if the limitations are not followed.
2. There are no operator serviceable parts inside this equipment.
Service should be provided only by a qualified service technician.
3. This equipment is provided with a detachable power cord which
has an integral safety ground wire intended for connection to a
grounded safety outlet.
a. Do not substitute the power cord with one that is not the
provided approved type. Never use an adapter plug to
connect to a 2-wire outlet as this will defeat the continuity of
the grounding wire.
b. The equipment requires the use of the ground wire as a part
of the safety certification, modification or misuse can provide
a shock hazard that can result in serious injury or death.
c. Contact a qualified electrician or the manufacturer if there
are questions about the installation prior to connecting the
equipment.
d. Protective earthing is provided by Listed AC adapter. Building
installation shall provide appropriate short-circuit backup
protection.
e. Protective bonding must be installed in accordance with
local national wiring rules and regulations.
General Warranty
UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) represents
and warrants that the Products furnished hereunder shall be free
from defects in material and workmanship for a period of one (1)
year from the date of shipment by UBIQUITI NETWORKS under
normal use and operation. UBIQUITI NETWORKS sole and exclusive
obligation under the foregoing warranty shall be to repair or
replace, at its option, any defective Product that fails during the
warranty period. The expense of removal and reinstallation of any
item is not included in this warranty.
The foregoing warranty is exclusive and in lieu of all other
11
General Warranty
warranties, express or implied, including the implied warranties
of merchantability and fitness for a particular purpose and any
warranties arising from a course of dealing, usage or trade practice
with respect to the products. Repair or replacement in the manner
provided herein shall be the sole and exclusive remedy of Buyer
for breach of warranty and shall constitute fulfillment of all
liabilities of UBIQUITI NETWORKS with respect to the quality and
performance of the Products. UBIQUITI NETWORKS reserves the
right to inspect all defective Products (which must be returned by
Buyer to UBIQUITI NETWORKS factory freight prepaid).
No Products will be accepted for replacement or repair without
obtaining a Return Materials Authorization (RMA) number from
UBIQUITI NETWORKS. Products returned without an RMA number
will not be processed and will be returned to Buyer freight collect.
UBIQUITI NETWORKS shall have no obligation to make repairs
or replacement necessitated by catastrophe, fault, negligence,
misuse, abuse, or accident by Buyer, Buyer’s customers or any
other parties. The warranty period of any repaired or replaced.
Product shall not extend beyond its original term.
Warranty Conditions
The foregoing warranty shall apply only if:
(I) The Product has not been subjected to misuse, neglect or unusual
physical, electrical or electromagnetic stress, or some other type
of accident.
(II) No modification, alteration or addition has been made to
the Product by persons other than UBIQUITI NETWORKS
or UBIQUITI NETWORK’S authorized representatives or
otherwise approved by UBIQUITI NETWORKS.
(III) The Product has been properly installed and used at all times
in accordance, and in all material respects, with the applicable
Product documentation.
(IV) All Ethernet cabling runs use CAT5 (or above) shielded cabling.
Disclaimer: UBIQUITI NETWORKS does not warrant that the
operation of the products is error-free or that operation will
be uninterrupted. In no event shall UBIQUITI NETWORKS be
responsible for damages or claims of any nature or description
relating to system performance, including coverage, buyer’s
12
Bullet™ M Titanium Quick Start Guide
selection of products for buyer’s application and/or failure of
products to meet government or regulatory requirements.
Returns
In the unlikely event a defect occurs, please work through the
dealer or distributor from which this product was purchased.
Compliance
FCC
Changes or modifications not expressly approved by Ubiquiti
Networks, Inc. could void the user’s authority to operate the
equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including
interference that may cause undesired operation of the device.
NOTE: This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment
is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operations
of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
RF Exposure Warning
The transceiver described here emits radio frequency energy.
Although the power level is low, the concentrated energy from
a directional antenna may pose a health hazard. Do not allow
people to come closer than 157 cm to the antenna when the
transmitter is operating.
Additional information on RF exposure is available on the Internet
at www.fcc.gov/oet/info/documents/bulletins
13
Compliance
L'émetteur-récepteur décrit ici émet de l'énergie de fréquence
radio. Bien que le niveau de puissance est faible, l'énergie
concentrée à partir d'une antenne directionnelle peut présenter
un danger pour la santé. Ne pas permettre aux gens de se
rapprocher de 157 cm à l'antenne lorsque l'émetteur est en
marche.
Des renseignements supplémentaires sur l'exposition aux RF est
disponible sur Internet à www.fcc.gov/oet/info/documents/
bulletins
CE Marking
CE marking on this product represents the product is in
compliance with all directives that are applicable to it.
Alert sign! Follows CE marking
Alert sign must be indicated if a restriction on use applied to the
product and it must follow the CE marking.
NB-Identification number (if there is any)
Notified body number is indicated if it is involved in the
conformity assessment procedure.
Please check the CE mark on the product label to find out which
notified body was involved during assessment.
14
Bullet™ M Titanium Quick Start Guide
Declaration of Conformity
Česky
[Czech]
UBIQUITI NETWORKS tímto prohla uje, e tento UBIQUITI
NETWORKS device, je ve shod se základními po adavky a dal ími p
íslu n mi ustanoveními sm rnice 1999/5/ES.
Dansk
[Danish]
Undertegnede UBIQUITI NETWORKS erklærer herved, at følgende
udstyr UBIQUITI NETWORKS device, overholder de væsentlige krav
og øvrige relevante krav i direktiv 1999/5/EF.
Nederlands
[Dutch]
Hierbij verklaart UBIQUITI NETWORKS dat het toestel UBIQUITI
NETWORKS device, in overeenstemming is met de essentiële eisen
en de andere relevante bepalingen van richtlijn 1999/5/EG.
Bij deze verklaart UBIQUITI NETWORKS dat deze UBIQUITI
NETWORKS device, voldoet aan de essentiële eisen en aan de
overige relevante bepalingen van Richtlijn 1999/5/EC.
English
Hereby, UBIQUITI NETWORKS, declares that this UBIQUITI
NETWORKS device, is in compliance with the essential requirements
and other relevant provisions of Directive 1999/5/EC.
Eesti
[Estonian]
Käesolevaga kinnitab UBIQUITI NETWORKS seadme UBIQUITI
NETWORKS device, vastavust direktiivi 1999/5/EÜ põhinõuetele ja
nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.
Suomi
[Finnish]
UBIQUITI NETWORKS vakuuttaa täten että UBIQUITI NETWORKS
device, tyyppinen laite on direktiivin 1999/5/EY oleellisten
vaatimusten ja sitä koskevien direktiivin muiden ehtojen
mukainen.
Français
[French]
Par la présente UBIQUITI NETWORKS déclare que l’appareil
UBIQUITI NETWORKS, device est conforme aux exigences
essentielles et aux autres dispositions pertinentes de la directive
1999/5/CE.
Deutsch
[German]
Hiermit erklärt UBIQUITI NETWORKS, dass sich diese UBIQUITI
NETWORKS device, in Übereinstimmung mit den grundlegenden
Anforderungen und den anderen relevanten Vorschriften der
Richtlinie 1999/5/EG befindet”. (BMWi)
Ελληνική
[Greek]
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ UBIQUITI NETWORKS ΔΗΛΩΝΕΙ ΟΤΙ UBIQUITI
NETWORKS device, ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ
ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ
1995/5/ΕΚ.
Magyar
[Hungarian]
Alulírott, UBIQUITI NETWORKS nyilatkozom, hogy a
UBIQUITI NETWORKS device, megfelel a vonatkozó alapvetõ
követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Íslenska
[Icelandic]
Hér me l sir UBIQUITI NETWORKS yfir ví a UBIQUITI NETWORKS
device, er í samræmi vi grunnkröfur og a rar kröfur, sem ger ar eru í
tilskipun 1999/5/EC.
Italiano
[Italian]
Con la presente UBIQUITI NETWORKS dichiara che questo UBIQUITI
NETWORKS device, è conforme ai requisiti essenziali ed alle altre
disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
15
Declaration of Conformity
Latviski
[Latvian]
Ar o UBIQUITI NETWORKS deklar , ka UBIQUITI NETWORKS device,
atbilst Direkt vas 1999/5/EK b tiskaj m pras b m un citiem ar to saist
tajiem noteikumiem.
Lietuviškai
[Lithuanian]
UBIQUITI NETWORKS deklaruoja, kad šis UBIQUITI NETWORKS
įrenginys atitinka esminius reikalavimus ir kitas 1999/5/EB
Direktyvos nuostatas.
Malti
[Maltese]
Hawnhekk, UBIQUITI NETWORKS, jiddikjara li dan UBIQUITI
NETWORKS device, jikkonforma mal- ti ijiet essenzjali u ma
provvedimenti o rajn relevanti li hemm fid-Dirrettiva 1999/5/EC.
Norsk
[Norwegian]
UBIQUITI NETWORKS erklærer herved at utstyret UBIQUITI
NETWORKS device, er i samsvar med de grunnleggende krav og
øvrige relevante krav i direktiv 1999/5/EF.
Slovensky
[Slovak]
UBIQUITI NETWORKS t mto vyhlasuje, e UBIQUITI NETWORKS
device, sp a základné po iadavky a v etky príslu né ustanovenia
Smernice 1999/5/ES.
Svenska
[Swedish]
Härmed intygar UBIQUITI NETWORKS att denna UBIQUITI
NETWORKS device, står I överensstämmelse med de väsentliga
egenskapskrav och övriga relevanta bestämmelser som framgår av
direktiv 1999/5/EG.
Español
[Spanish]
Por medio de la presente UBIQUITI NETWORKS declara que el
UBIQUITI NETWORKS device, cumple con los requisitos esenciales
y cualesquiera otras disposiciones aplicables o exigibles de la
Directiva 1999/5/CE.
Polski
[Polish]
Niniejszym, firma UBIQUITI NETWORKS o wiadcza, e produkt serii
UBIQUITI NETWORKS device, spełnia zasadnicze wymagania i inne
istotne postanowienia Dyrektywy 1999/5/EC.
Português
[Portuguese]
UBIQUITI NETWORKS declara que este UBIQUITI NETWORKS device,
está conforme com os requisitos essenciais e outras disposições da
Directiva 1999/5/CE.
Română
[Romanian]
Prin prezenta, declarăm că acest produs este în conformitate cu
cerinţele esenţiale şi cu alte prevederi relevante din Directiva
1999/5/CE.
PH111511
English
We recommend that you protect your networks
from the most brutal environments and
devastating ESD attacks with industrial-grade
shielded Ethernet cable from Ubiquiti Networks.
For more details, visit www.ubnt.com/toughcable
Deutsch
Schützen Sie Ihre Netzwerke vor extremen Umwelteinflüssen
und verheerender elektrostatischer Entladung (ESD), indem
Sie abgeschirmte Ethernetkabel in Unternehmensqualität von
Ubiquiti Networks verwenden. Weitere Informationen erhalten Sie
unter www.ubnt.com/toughcable
Español
Le recomendamos que proteja sus redes de los entornos más
hostiles y los devastadores efectos de las descargas electrostáticas
utilizando cable Ethernet blindado con calidad-industrial de
Ubiquiti Networks. Para obtener más información, visite
www.ubnt.com/toughcable
Français
Nous vous recommandons de protéger vos réseaux contre les
environnements les plus brutaux et les décharges électrostatiques
les plus dévastatrices avec un câble Ethernet Ubiquiti Networks
avec blindage renforcé. Pour en savoir plus, rendez-vous sur
www.ubnt.com/toughcable
Italiano
Si consiglia di proteggere le reti dagli ambienti e dagli attacchi
ESD più invasivi con il cavo Ethernet schermato-di tipo industriale
di Ubiquiti Networks. Per ulteriori informazioni, visitare il sito Web
www.ubnt.com/toughcable
Ubiquiti Networks Support
Email: suppor[email protected]om
Phone (9 a.m. - 5 p.m. PST): 408-942-1153
Online Resources
Wiki Page: www.ubnt.com/wiki
Support Forum: www.ubnt.com/forum
Downloads: www.ubnt.com/support/downloads
www.ubnt.com
© 2011 Ubiquiti Networks, Inc. All rights reserved.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
Ubiquiti Networks Bullet M BM2-Ti Specificație
- Tip
- Specificație
- Acest manual este potrivit și pentru
în alte limbi
Lucrări conexe
Alte documente
-
Ubiquiti BULLET AC Manual de utilizare
-
-
-
-
-
-
-
-
-
Danfoss 013G0290 Ghid de instalare