Parkside PGG 15 A1 Operation and Safety Notes

POWER ENGRAVING TOOL PGG 15 A1

7

POWER ENGRAVING TOOL

Operation and Safety Notes

Translation of original operation manual

Η

ΛΕΚΤΡΙΚΗ ΣΥΣΚΕΥΗ ΧΑΡΑΚΤΙΚΗΣ

Υποδείξεις χειρισμού και ασφαλείας

Μετάφραση των αυθεντικών οδηγιών λειτουργίας

GRA VIERGERÄ T

Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung

UREĐAJ ZA GRAVIRANJE

Upute za posluživanje i za Vašu sigurnost

Prijevod originalnih uputa za uporabu

APARAT DE GRAVURĂ

Instrucţiuni de utilizare şi de siguranţă

Traducerea instrucţiunilor de utilizare originale

УРЕД ЗА ГРАВИРАНЕ

Инструкции за обслужване и безопасност

Превод на оригиналното ръководство за експлоатация

66133_Mini-Graviergerät_cover_LB7.indd 6 01.06.11 15:28

GB / CY Operation and Safety Notes Page 5

HR Upute za posluživanje i za Vašu sigurnost Stranica 21

RO Instrucţiuni de utilizare şi de siguranţă Pagina 37

BG Инструкции за обслужване и безопасност страница 53

GR / CY Υποδείξεις χειρισμού και ασφαλείας Σελίδα 69

DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 85

Before reading, unfold the page containing the illustrations and familiarise yourself with all

functions of the device.

Prije nego što pročitate tekst, otvorite stranicu sa slikama i upoznajte se na osnovu toga sa

svim funkcijama uređaja.

Înainte de a citi instrucţiunile, priviţi imaginile şi familiarizaţi-vă cu toate funcţiile aparatului.

Преди да прочетете отворете страницата с фигурите и след това се запознайте с

всички функции на уреда.

Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα με τις εικόνες και εξοικειωθείτε με όλες τις

λειτουργίες της συσκευής.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich

anschließend mit allen Funktionen des Gerätes vertraut.

УРЕД ЗА ГРАВИРАНЕ

Инструкции за обслужване и безопасност

Превод на оригиналното ръководство за експлоатация

66133_Mini-Graviergerät_cover_LB7.indd 7 01.06.11 15:28

B

1 2 3

45

6

A

7

66133_Mini-Graviergerät_cover_LB7.indd 8 01.06.11 15:28

66133_Mini-Graviergerät_cover_LB7.indd 9 01.06.11 15:28

5 GB/CY

Table of contents

Introduction

Proper use ..............................................................................Page 7

Features and equipment ....................................................... Page 7

Included items .......................................................................Page 8

Technical details ....................................................................Page 8

General safety advice for

electrical power tools

1. Workplace safety .............................................................Page 9

2.

Electrical safety ................................................................. Page 10

3. Personal safety ..................................................................Page 11

4.

Careful handling and use of electrical power tools .......Page 12

Operation

Switching on / off ..................................................................Page 13

Setting the stroke rate ...........................................................Page 14

Changing the engraving point .............................................Page 14

Advice on use ........................................................................Page 15

Cleaning .............................................................................Page 15

Service .................................................................................Page 15

Warranty ...........................................................................Page 16

Disposal ..............................................................................Page 17

Manufacturer’s Declaration of

Conformity / Manufacturer .................................Page 18

66133_Mini-Graviergerät_content_LB7.indd 5 03.06.11 16:57

6 GB/CY

Introduction

The following pictograms are used in these operating

instructions / on the device:

Read instruction manual!

V

~

Volt (AC)

A

Amps

Observe caution and safety notes!

Risk of explosion!!

Keep children away from electrical power tools!

Caution – electric shock! Danger to life!

Risk of loss of life by electric shock from damaged mains

lead or mains plug!

Wear hearing protection, dust protection mask, protective

glasses and protective gloves.

Dispose packaging and appliance in an environmen-

tally-friendly way!

66133_Mini-Graviergerät_content_LB7.indd 6 03.06.11 16:57

7 GB/CY

Introduction

Power engraving tool PGG 15 A1

Introduction

Please make sure you familiarise yourself fully with the way

the device works before you use it for the ﬁrst time and that

you understand how to handle electrical power tools correctly.

To help you do this please read the accompanying operating instructions.

Keep these instructions in a safe place. If you pass the device on to an-

yone else, please ensure that you also pass on all the documentation.

Proper use

This product is intended for engraving or decorating materials such

as metal, plastic, glass, ceramic, wood and leather. Any other use or

modiﬁcation to the drill / grinder shall be considered as improper use

and could give rise to considerable dangers. The manufacturer will not

accept liability for loss or damage arising from improper use. Not

intended for commercial use.

Features and equipment

1

ON / OFF switch

2

Stroke switch

3

Hanging eye

4

Mains lead

5

Engraving point

6

Engraving point holder

7

Engraving stencils

66133_Mini-Graviergerät_content_LB7.indd 7 03.06.11 16:57

8 GB/CY

Introduction / General safety advice for electrical power tools

Introduction

Included items

1 Power engraving tool PGG 15 A1

2 Engraving stencils

1 Operating instructions

Technical details

Rated voltage: 230 V∼ 50 Hz

Mode of operation: intermittent operation: S3 20 %

Rated current: 0.15 A

Stroke rate: 6000 min

-1

Noise and vibration data:

Measured values for noise are determined in accordance with

EN 60745. The A-weighted noise level of the electrical power tool

are typically:

Sound pressure level: 74.4 dB(A)

Sound power level: 85.4 dB(A)

Uncertainty K: 3 dB

Wear ear protection!

Evaluated acceleration, typical:

Hand / arm vibration: 1.582 m / s

2

Uncertainty K = 1.5 m / s

2

The vibration level given in these instructions has

been measured in accordance with a standardised measurement pro-

cedure speciﬁed in EN 60745 and can be used to compare devices.

66133_Mini-Graviergerät_content_LB7.indd 8 03.06.11 16:57

9 GB/CY

Introduction / General safety advice for electrical power tools

Diﬀerent uses of the device give rise to diﬀerent vibration levels and in

many cases they may exceed the values given in these instructions. It is

easy to underestimate the vibration load if the electrical power tool is

used regularly in particular circumstances.

Note: If you wish to make an accurate assessment of the vibration

loads experienced during a particular period of working, you should

also take into account the intervening periods of time when the device

is switched oﬀ or is running but is not actually in use. This can result in

a much lower vibration load over the whole of the period of working.

General safety advice for

electrical power tools

Read all the safety advice and instruction

s!

Failure to observe the safety advice and instructions may result in electric

shock, ﬁre and / or serious injury.

Keep all the safety advice and instructions in a safe place

for future reference!

The term “electrical tool” used in the safety advice refers to electrical

tools powered by mains electricity (by means of a mains lead) and elec-

trical tools powered by rechargeable batteries (without a mains lead).

1. Workplace safety

a) Keep your working area clean and well lit. Untidy or

poorly lit working areas can lead to accidents.

66133_Mini-Graviergerät_content_LB7.indd 9 03.06.11 16:57

10 GB/CY

General safety advice for electrical power tools

b) Do not work with the device in potentially

explosive environments in which there are

inflammable liquids, gases or dusts. Electrical

power tools create sparks, which can ignite dusts or fumes.

c)

Keep children and other people away while

you are operating the electrical tool. Distrac-

tions can cause you to lose control of the device.

2. Electrical safety

a)

T

he mains plug on the device must match the mains

socket. The plug must not be modified in any way.

Do not use an adapter plug with devices fitted with

a protective earth. Unmodiﬁed plugs and matching sockets

reduce the risk of electric shock.

b) Avoid touching earthed surfaces such as pipes, radia-

tors, ovens and refrigerators with any part of your

body. There is an increased risk of electric shock if your body is

earthed

.

c) Keep the device away from rain or moisture. Water en-

tering an electrical device increases the risk of electric shock.

d)

Do not use the mains lead for any purpose for

which it was not intended, e.g. to carry the de-

vice, to hang up the device or to pull the mains

plug out of the mains socket. Keep the mains lead

away

from heat, oil, sharp edges or moving parts of the

device. Damaged or tangled mains leads increase the risk of

electric shock.

e) When working outdoors with an electrical power tool

always use extension cables that are also approved

66133_Mini-Graviergerät_content_LB7.indd 10 03.06.11 16:57

11 GB/CY

General safety advice for electrical power tools

for use outdoors. The use of an extension cable suitable for

outdoor use reduces the risk of electric shock.

f) Use a residual current device (RCD) for protection if

operating the electrical power tool in a moist environ-

ment is unavoidable. The use of an RCD reduces the risk of

electric shock.

3. Personal safety

a) Remain alert at all times, watch what you are doing

and always proceed with caution. Do not use the de-

vice if you are tired or under the influence of

drugs,

alcohol or medication. One mo

ment of carelessness when using

the device can lead to serious injury.

b)

Wear personal protective equipment and

always wear safety glasses. The wearing of per-

sonal protective equipment such as dust masks, non-slip

safety shoes, safety helmets or ear protectors, appropriate to the

type of electrical power tool used and work undertaken, reduces

the risk of injury.

c) Avoid unintentional operation of the device. Check

that the electrical power tool is switched off before y

ou

connect it to the mains, pick it up or carry it. Accidents

can happen if you carry the device with your ﬁnger on the ON /

OFF switch or with the device switched on.

d) Remove any setting tools or spanners before you

switch the device on. A tool or spanner left attached to a

rotating part of a device can lead to injury.

e) Avoid placing your body in an unnatural position.

Keep proper footing and balance at all times. By doing

66133_Mini-Graviergerät_content_LB7.indd 11 03.06.11 16:57

12 GB/CY

General safety advice for electrical power tools

this you will be in a better position to control the device in unfore-

seen circumstances.

f) Wear suitable clothing. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves clear of

moving parts. Loose clothing, jewellery or long hair can become

trapped in moving parts.

g) If vacuum dust extraction and collection devices are fit

ted

do not forget to check that they are properly con

nected

and correctly used. The use of these devices reduces the haz-

ard presented by dust.

4. Careful handling and use of

electrical power tools

a) Do not overload the device. Always use an electrical

power tool that is intended for the task you are un-

dertaking. By using the right electrical power tool for the job

you will work more safely and achieve a better result.

b) Do not use an electrical power tool if its switch is de-

fective. An electrical power tool that can no longer be switched

on and oﬀ is dangerous and must be repaired.

c) Pull the mains plug from the socket before you make

any adjustments to the device, change accessories or

when the device is put away. This precaution is intended to

prevent you from unintentionally starting the device.

d) When not in use always ensure that electrical power

tools are kept out of reach of children. Do not let any-

one use the device if he or she is not familiar with it

or has not read the instructions and advice. Electrical

power tools are dangerous when they are used by inexperienced

people.

66133_Mini-Graviergerät_content_LB7.indd 12 03.06.11 16:57

13 GB/CY

General safety advice for electrical power tools / Operation

e) Look after the device carefully. Check that moving

parts are working properly and move freely. Check

for any parts that are broken or damaged enough to

detrimentally affect the functioning of the device.

Have damaged parts repaired before you use the

device. Many accidents have their origins in poorly maintained

electrical power tools.

f) Keep cutting tools clean and sharp. Carefully maintained

cutting tools with sharp cutting edges are less likely to jam and

are easier to control.

g) Use the electrical power tool, accessories, inserted

tools etc. in accordance with these instructions and ad-

vice, and the stipulations drawn up for this particular

type of device. In doing this, take into account the

working conditions and the task in hand. The use of

electrical power tools for purposes other than those intended can

lead to dangerous situations.

Operation

Never use the device for a purpose for which it was not intended or

with non-original parts / accessories. The use of tools or accessories

other than those recommended in the operating instructions could lead

to you suﬀering an injury.

Switching on / oﬀ

Insert the mains plug into a mains socket.

66133_Mini-Graviergerät_content_LB7.indd 13 03.06.11 16:57

14 GB/CY

Operation

Switching on:

Press the ON / OFF switch

1

.

Switching off:

Release the ON / OFF switch

1

.

Setting the stroke rate

The stroke switch

2

is used to set the penetration depth of the engrav-

ing. A low setting is normally adequate for most engraving tasks.

Turn the switch for the number of strokes

2

in the + direction to

increase the penetration depth.

Turn the switch for the number of strokes

2

in the – direction to

decrease the penetration depth.

Note: Take care when increasing the penetration depth that you do

not turn the stroke switch

2

too far in the + direction. Otherwise the

switch could screw oﬀ the device.

Changing the engraving point

RISK OF INJURY! Switch the device oﬀ before

performing any tasks on the device and pull the mains plug out of the

mains socket.

Replace the engraving point

5

as soon as it becomes too worn

and no longer provides the desired engraving performance. Turn

the engraving point holder

6

anticlockwise until the engraving

point

5

is released.

66133_Mini-Graviergerät_content_LB7.indd 14 03.06.11 16:57

15 GB/CY

Operation / Cleaning

Remove the spring and the plain washer.

Push the plain washer and spring on to a new engraving point

5

.

Then insert this and turn the engraving point holder

6

clockwise

to lock the engraving point in position.

Ensure that the engraving point

5

is properly ﬁxed in position.

Advice on use

You can use the mini-engraver to produce creative, individual engravings.

For example, you can use it to place identifying marks on your valuables.

You can place numbers and letters on metal, glass, plastic, wood and

ceramic. This is done with the help of the supplied engraving stencils

7

,

see Figs. A and B.

Hold the device at an angle, as you would a pencil.

Your arm should rest on the table.

Using very light pressure, guide the engraving point

5

over the

workpiece. Find the ideal speed of movement by trial and error on

a piece of waste material.

Note: The engraving point

5

supplied with the product is made

from tungsten steel. Therefore it is not suitable for engraving electronic

media such as CDs, DVDs etc. It could damage these materials and

render them illegible.

Cleaning

Before performing any cleaning or maintenance

work, always remove the mains plug from the socket.

Clean all the dirt oﬀ the device. Use a dry cloth for cleaning.

66133_Mini-Graviergerät_content_LB7.indd 15 03.06.11 16:57

16 GB/CY

Service / Warranty

Service

Have your device repaired at the ser-

vice centre or by qualified specialist personnel using

original manufacturer parts only. This will ensure that your

device remains safe to use.

If the plug or lead needs to be re-

placed, always have the replacement carried out by

the manufacturer or its service centre. This will ensure that

your device remains safe to use.

Warranty

The warranty for this appliance is for 3 years from the

date of purchase. The appliance has been manufactured

with care and meticulously examined before delivery.

Please retain your receipt as proof of purchase. In the

event of a warranty claim, please make contact by tele-

phone with our Service Department. Only in this way

can a post-free despatch for your goods be assured.

The warranty covers only claims for material and maufacturing defects,

but not for transport damage, for wearing parts or for damage to frag-

ile components, e.g. buttons or batteries. This product is for private use

only and is not intended for commercial use.

The warranty is void in the case of abusive and improper handling,

use of force and internal tampering not carried out by our authorized

service branch. Your statutory rights are not restricted in any way by

this warranty.

66133_Mini-Graviergerät_content_LB7.indd 16 03.06.11 16:57

17 GB/CY

Warranty / Disposal

The warranty period will not be extended by repairs made unter war

ranty.

This applies also to replaced and repaired parts. Any damage and de-

fects extant on purchase must be reported immediately after unpacking

the appliance, at the latest, two days after the purchase date. Repairs

made after the expiration of the warranty period are subject to payment.

GB

Service Great Britain

Tel.: 0871 5000 720

(0,10 GBP/Min.)

e-mail: kom[email protected]

IAN 66133

CY

Service Cyprus

Tel.: 8009 4409

e-mail: kom[email protected]

IAN 66133

Disposal

The packaging is wholly composed of environmentally-

friendly materials that can be disposed of at a local

recycling centre.

Do not dispose of electric tools in

the household waste!

66133_Mini-Graviergerät_content_LB7.indd 17 03.06.11 16:57

18 GB/CY

Disposal / Declaration of conformity / Producer

In accordance with European Directive 2002 / 96 / EC about waste

electrical and electronic equipment and its transposition into national

legislation, worn out electric tools must be collected separately and

taken for environmentally compatible recycling.

Contact your local refuse disposal authority for more details of how to

dispose of your worn out electrical devices.

Manufacturer’s Declaration of

Conformity / Manufacturer

We, Kompernaß GmbH, the person responsible for documents:

Mr Semi Uguzlu, Burgstr. 21, D-44867 Bochum, Germany, hereby

declare that this product complies with the following standards, norma-

tive documents and EU directives:

Machinery Directive

(2006 / 42 / EC)

EU Low Voltage Directive

(2006 / 95 / EC)

Electromagnetic compatibility

(2004 / 108 / EC)

66133_Mini-Graviergerät_content_LB7.indd 18 03.06.11 16:57

19 GB/CY

Declaration of conformity / Producer

Applicable harmonized standards

EN 60745-1:2009

EN ISO 12100-2/A1:2009

EN 55014-1:2006

EN 55014-2/A2:2008

EN 61000-3-2:2006

EN 61000-3-3:2008

Type / Device description:

Power engraving tool PGG 15 A1

Date of manufacture (DOM): 06 - 2011

Serial number: IAN 66133

Bochum, 30.06.2011

Semi Uguzlu

- Quality Manager -

We reserve the right to make technical modiﬁcations in the course of

further development.

66133_Mini-Graviergerät_content_LB7.indd 19 03.06.11 16:57

Popis sadržaja

20

66133_Mini-Graviergerät_content_LB7.indd 20 03.06.11 16:57

Pagina se încarcă ...

Parkside PGG 15 A1 Operation and Safety Notes

Parkside PGG 15 A1 Operation and Safety Notes

Lucrări conexe

Alte documente