Parkside PKGA 20-Li C2 Manual de utilizare

4-in-1 Cordless Combination Tool PKGA 20-Li C2

4 u 1 aku kombinirani uređaj

Prijevod originalnih uputa za uporabu

Mașină combi 4 în 1, cu acumulator

Traducerea instrucţiunilor de utilizare originale

4-in-1-Akku-Kombigerät

Originalbetriebsanleitung

Комбиниран уред 4 в 1

Превод на оригиналното ръководство за експлоатация

Aku kombinovani uređaj 4 u 1

Prevod originalnog uputstva za upotrebu

4-in-1 Cordless Combination Tool

Translation of the original instructions

Επαναφορτιζόενο πολυεργαλείο

4 σε 1

Μετάφραση των αυθεντικών οδηγιών λειτουργία

IAN 360557_ 2010

4-in-1 Cordless Combination Tool PKGA 20-Li C2

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of

the device.

Prije nego što pročitate tekst, otvorite stranicu sa slikama i upoznajte se na osnovu toga sa svim

funkcijama uređaja.

Pre čitanja rasklopite stranu sa uređajima i u sledećem koraku upoznajte se sa svim funkcijama uređaja.

Înainte de a citi instrucţiunile, priviţi imaginile şi familiarizaţi-vă cu toate funcţiile aparatului.

Преди да прочетете отворете страницата с фигурите и след това се запознайте с всички функции

на уреда.

Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα ε τι εικόνε και εξοικειωθείτε ε όλε τι λειτουργίε

τη συσκευή.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit

allen Funktionen des Gerätes vertraut.

GB / CY Translation of the original instructions Page 4

HR Prijevod originalnih uputa za uporabu Stranica 24

RS Prevod originalnog uputstva za upotrebu Strana 44

RO Traducerea instrucţiunilor de utilizare originale Pagina 65

BG Превод на оригиналното ръководство за експлоатация

Страница 87

GR / CY Μετάφραση των αυθεντικών οδηγιών λειτουργία Σελίδα 111

DE / AT / CH Originalbetriebsanleitung Seite 134

1 2 356

7

8

9

10

11 12

13

14

16 19

17

18

20 23 24

25

26 27 30 31 32 33

28 29

2221

15

4

9a

9b

4

GB CY

Content

Introduction .................................5

Intended Use ................................5

General Description ......................5

Scope of delivery .............................. 5

Overview ......................................... 6

Technical Data ..............................6

Notes on Safety ...........................7

Symbols ........................................... 7

General Safety Directions for

Power Tools ...................................... 8

Additional safety instructions ............ 11

Practical tips ..............................13

Operation ..................................13

Replacing the appliance attachment .. 13

 .......... 14

Switching on/off ............................. 14

 ..... 14

Recharging the battery ..................... 14

Motor unit with drill attachment

PKGA1 .......................................15

Changing the tool ........................... 15

Choice of gear ............................... 15

Set the direction of rotation .............. 15

Torque adjustment ........................... 15

Motor unit with multisander

attachment PKGA2 .....................16

Attaching/removing sanding sheet .... 16

Connecting dust extraction ............... 16

Sanding ......................................... 16

Selection of sanding sheet ................ 16

Translation of the original EC

declaration of conformity ......... 156

Exploded Drawings ...........163-165

Motor unit with sabre saw

attachment PKGA3 .....................17

Installing/changing the blade ........... 17

Operating the sabre saw ................. 17

Sawing .......................................... 17

Plunge cuts ..................................... 17

Selection of sawblade ..................... 18

Motor unit with multifunction

tool PKGA4 ................................ 18

Changing the tool ........................... 18

Attaching/removing sanding sheet .... 18

Sanding ......................................... 18

Selection of sanding sheet ................ 19

Scraping ........................................ 19

Cleaning/Maintenance ...............19

Cleaning ........................................ 19

Maintenance .................................. 19

Storage ......................................19

Waste Disposal/Environmental

Protection ..................................19

Guarantee .................................20

Repair Service ............................21

Service-Center ............................21

Importer .................................... 21

Spare Parts/Accessories ............. 22

Trouble Shooting ........................ 23

5

CYGB

Introduction

Congratulations on the purchase of your

new device. With it, you have chosen a

high quality product. During production,

this equipment has been checked for



The functionality of your equipment is

therefore guaranteed.

The operating instructions constitute

part of this product. They contain

important information on safety, use

and disposal.

Before using the product, familiarise

yourself with all of the operating and

safety instructions. Use the product only

as described and for the applications



the event that the product is passed on,

hand over all documents to the third party.

Intended Use

The device is intended for tightening and

releasing screws and for drilling holes in

wood, metal or plastic.

The device is not suitable for commercial

use. Any other use that is not explicitly

approved in these instructions may result in

damage to the equipment and represent a

serious danger to the user.

The equipment is designed for use by

adults. Adolescents over the age of 16

may use the device only under supervision.

The manufacturer is not liable for damages



operation. Commercial use will invalidate

the guarantee.

The device is part of the Parkside





batteries.

The batteries may only be charged using



series.

General Description

The illustration of the principal

functioning parts can be found

on the front and back foldout

pages.

Scope of delivery

Carefully unpack the trimmer and check

that it is complete. Dispose of the packag-

ing material correctly.

• Motor unit with drill attachment

• Sabre saw attachment

• Multi-sander attachment

• Multifunction tool

• Accessories for drill attachment

- 6 drill bits (1,5/2/3/4/5/6 mm)

- 6 screwdriver bits, 50 mm

- Bit holder

• Accessories for sabre saw attachment

- Wood sawblade (HCS150/6TPI)

- Metal sawblade (HSS150/18TPI)

• Accessories for multi-sander attachment

- 5 sanding sheets

(2 x P* 60, 2 x P 120, 1 x P 240)

• Accessories for multifunction tool

- Plunge sawblade

- Scraper blade

- Delta sanding plate with 3 sanding

sheets (1 x P* 60, 1 x P 80, 1 x P 120)

• Dust extraction adaptor

• Reducer

• Storage case

• Instruction Manual

*P = Grain size

6

GB CY

Battery and charger are not

included.

Overview

  

2 Torque adjustment ring

3 Gear selection switch

  

5 Unlocking lever for appliance at-

tachment

6 Motor unit

7 Direction switch

8 Handle

9 Rechargeable battery

10 On/off switch

11 Bit holder

12 Screwdriver bits, 50 mm, 6 no.

13 Drill bits 6 no.

14 Charger

15 Storage case

  

17 Footplate

18 Lever for unlocking sawblade

19 Metal sawblade

20 Wood sawblade

21 Sanding plate

  

23 5 sanding sheets

24 Dust extraction adaptor

25 Reducer

  

27 Lever for unlocking tool

28 Arbor

29 Tool holder

30 Delta sanding plate

31 3 sanding sheets

32 Scraper blade

33 Plunge sawblade

Technical Data

4-in-1 Cordless

Combination Tool ................PKGA 20-Li C2

Motor voltage ............................. 

Idling speed (n0) ....................21000 min-1

Temperature...........................

Charging process ...................

Operation .......................... 

Storage .................................

Motor unit with drill attachment ..... PKGA1

Idling speed (n0) ........ 0-400/0-1350 min-1

Torque ................................max. 35 Nm

Spread drill chuck ................ max. 13 mm

Drill diameter

for wood .......................... max. 13 mm

for steel ............................. max. 8 mm

Weight ......................................1.23 kg

Sound pressure level

(LpA) ................... 83.7pA= 5 dB

Sound power level

(LWA) ................. WA= 5 dB

h)

drilling in metal .. 1.322 m/s22

idling ..............1.531 m/s22

Motor unit with multisander

attachment .................................... PKGA2

Oscillation rate (n0) ..............0-9000 min-1

Sanding sheet size .......138 x 97 mm

Weight ...........................................1 kg

Sound pressure level

(LpA) ................... 88.6pA= 3 dB

Sound power level

(LWA) ................. WA= 3 dB

h) ......4.572 m/s22

Motor unit with sabre saw

attachment .................................... PKGA3

Stroke rate (n0) .....................0-3200 min-1

Stroke length ...................... 22 mm

7

CYGB

Cutting capacity

Wood .................................... 100 mm

Metal ...................................... 50 mm

Weight ......................................1.44 kg

Sound pressure level

(LpA) ................... 89.3pA= 5 dB

Sound power level

(LWA) ............... WA= 5 dB

h), Sawing

boards ..........12.395 m/s2; 2

wood beams ..12.392 m/s22

Motor unit with multifunction tool ... PKGA4

Oscillation rate (n0) ............0-20000 min-1

Oscillation angle ..............................

Weight ...........................................1 kg

Sound pressure level

(LpA) ................... 84.8pA= 3 dB

Sound power level

(LWA) ................. WA= 3 dB

h) ......4.229m/s22

Attention! An up-to-date list

of battery compatibility can

be found at:

www.lidl.de/akku

The stated vibration emission value was

measured in accordance with a standard

testing procedure and may be used to com-

pare one power tool to another.

The stated vibration emission value may

also be used for a preliminary exposure

assessment.

Warning: The vibration emission

value may differ during actual use

of the power tool from the stated

value depending on the manner in

which the power tool is used.

Try to keep the exposure to vibra-



of measures to reduce vibration

exposure are the wearing of gloves

when using the tool (except: operat-

ing mode drilling) and limiting the

working hours. For this purpose all

parts of the operating cycle have to

be considered (for example, times

when the electric tool is switched

off and times when it is switched on

but running without any load).

Notes on Safety

This section details the basic safety instruc-

tions for working with the appliance.

Symbols

Symbols in the manual

Warning symbols with in-

formation on damage and

injury prevention.

Hazard symbol with infor-

mation on the prevention of

personal injury caused by

electric shock.

Instruction symbols with information

on preventing damage.

Wear safety gloves.

Wear ear protection.

Wear a protective mask.

Help symbols with information on

improving tool handling.

Symbols on the Equipment

Read through the instruction manual

carefully.

8

GB CY



disposed of with the domestic

waste.

Stop appliance before

changing gear.

Injury hazard caused by rotating



This device is part of the Park-



Graphic symbols on the saw

blades:

Wear eye protection.

Suitable for sawing wood

Suitable for sawing metal

General Safety Directions for

Power Tools

WARNING! Read all safety

notices, instructions, illustra-

tions and technical data that

have been provided with this

power tool. Omissions in the

compliance with safety directions

and instructions can cause electrical



Retain all safety directions and in-

structions for future use.

The term „power tool“ in the warnings

refers to your mains-operated (corded)

power tool or battery-operated (cordless)

power tool).

1) WORK AREA SAFETY

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in

explosive atmospheres, such as



Iiquids, gases or dust. Power tools

create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders

away while operating a power

tool. Distractions can cause you to

lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match

the outlet. Never modify the

plug in any way. Do not use

any adapter plugs with earthed

(grounded) power tools. Unmodi-



reduce risk of electric shock.

b) Avoid body contact with

earthed or grounded surfaces,

such as pipes, radiators, ranges

and refrigerators. There is an in-

creased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to

rain or wet conditions. Water

entering a power tool will increase the

risk of electric shock.

d) Do not abuse the cord. Never

use the cord for carrying, pulling

or unplugging the power tool.

Keep cord away from heat, oil,

sharp edges or moving parts.

Damaged or entangled cords increase

the risk of electric shock.

e) When operating a power tool

outdoors, use an extension cord

suitable for outdoor use. Use of a

9

CYGB

cord suitable for outdoor use reduces

the risk of electric shock.

f) If operating a power tool in a

damp location is unavoidable,

use a residual current device

(RCD) protected supply. Use of an

RCD reduces the risk of electric shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are

doing and use common sense

when operating a power tool.

Do not use a power tool while

-

ence of drugs, alcohol or medi-

cation. A moment of inattention white

operating power tools may result in

serious personal injury.

b) Use personal protective equip-

ment. Always wear eye protec-

tion. Protective equipment such as

dust mask, non-skid safety shoes, hard

hat, or hearing protection used for

appropriate conditions will reduce per-

sonal injuries.

c) Prevent unintentional starting.

Ensure the switch is in the off-

position before connecting to

power source and/or battery

pack, picking up or carrying

the tool. Carrying power tools with



power tools that have the switch on

invites accidents.

d) Remove any adjusting key or

wrench before turning the pow-

er tool on. A wrench or a key left at-

tached to a rotating part of the power

tool may result in personal injury.

e) Do not overreach. Keep proper

footing and balance at all times.

This enables better control of the pow-

er tool in unexpected situations.

f) Dress properly. Do not wear

loose clothing or jewellery.

Keep your hair, clothing and

gloves away from moving

parts. Loose clothes, jewellery or long

hair can be caught in moving parts.

g) If dust extraction and collection

devices can be installed, make

sure that these are connected

and used correctly. Use of dust col-

lection can reduce dust-related hazards.

h) Do not allow yourself to be lulled

into a false sense of security and

do not disregard the safety rules

for power tools, even if you are

familiar with the power tool after

using it many times. Careless action

can lead to serious injuries within a frac-

tion of a second.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use

the correct power tool for your

application. The correct power tool

will do the job better and safer at the

rate for which it was designed.

b) Do not use the power tool if the

switch does not turn it on and

off. Any power tool that cannot be

controlled with the switch is dangerous

and must be repaired.

c) Remove the plug from the wall

socket and/or remove the re-

chargeable battery before you

change the device’s settings,

change accessory parts or put

away the power tool. Such pre-

ventive safety measures reduce the risk

of starting the power tool accidentaIly.

d) Store idle power tools out of the

reach of children and do not al-

low persons unfamiliar with the

power tool or these instructions

10

GB CY

to operate the power tool. Power

tools are dangerous in the hands of

untrained users.

e) Look after the power tool and

application tool carefully. Check

for misalignment or binding

of moving parts, breakage of

parts and any other condition

that may affect the power tool’s

operation. If damaged, have

the power tool repaired before

use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and

clean. Properly maintained cutting

tools with sharp cutting edges are less

Iikely to bind and are easier to control.

g) Use the power tool, accessories

and tool bits etc. in accordance

with these instructions, taking

into account the working condi-

tions and the work to be per-

formed. Use of the power tool for op-

erations different from those intended

could result in a hazardous situation.

h) Keep handles and grip surfaces

dry, clean and free from oil and

grease. Slippery handles and grip

surfaces do not permit safe operation

and control over the power tool in un-

expected situations.

5) CAREFUL HANDLING AND USE

OF BATTERY DEVICES

a) Charge the batteries only in

chargers that are recommended

by the manufacturer. 



of battery is used with other batteries.

b) In the power tools, use only the

batteries designed for the pur-

pose. The use of other batteries may



c) Keep the unused battery away

from paper clips, coins, keys,

nails, screws and other small

metal objects, which could

cause bridging of the contacts.

A short circuit between the battery con-



d) If used incorrectly, liquid may

leak from the battery. Avoid

contact with this. In the event of

accidental contact, rinse off with

water. If the liquid gets into eyes, seek

medical assistance. Leaking battery



e) Do not use damaged or altered

batteries. Damaged or altered bat-

teries can be unpredictable and lead



 

or elevated temperatures. Fire or



an explosion.

g) Follow all instructions for charg-

ing and never charge the bat-

tery or the battery-powered

tool outside the temperature

range stated in the operating

instructions. Incorrect charging or

charging outside the permitted tem-

perature range may destroy the battery



6) SERVICE

a) Have your power tool serviced

-

ing only identical replacement

parts. This will ensure that the safety

of the power tool is maintained.

b) Never repair damaged batter-

ies. All battery repairs should be car-

ried out by the manufacturer or author-

ised customer service centres only.

11

CYGB

Additional safety instructions

Warning! The processing

of hazardous materials



material containing asbestos)

is hazardous to the user and

bystanders and is therefore

prohibited.

Warning! Sawing and san-

ding can result in dust. Al-

ways wear safety goggles,

safety gloves and respiratory

protection. If possible, attach

a dust extraction system.

1) SPECIAL SAFETY INFORMATION

FOR THE CORDLESS COMBINA-

TION TOOL

• Hold the electric tool by the in-

sulated handle surfaces when

performing work where the

screw may come into contact

with hidden wiring. Contact of the

screw with a live wire can also cause

a charge in metal parts of the appli-

ance and result in an electric shock.

• Use suitable detectors in order



ask the local utility company.

Contact with electrical cables can lead



a gas pipe can result in an explosion.

Damage to a water pipe can lead to

property damaged and electric shock.

• Secure the workpiece. A work-

piece that is retained with clamping

appliances or a vice is held more se-

curely than with your hand.

• Be very careful when handling

tools such as saws, scraper

blades and drills. These are sharp

and present an injury hazard.

• Wear safety gloves when

changing attachments. This ena-

bles you to avoid injuries if the appli-

ance attachment has heated up after

use.

2) SAFETY INFORMATION FOR

SAWING BACK AND FORTH

• Hold the electric tool by the in-

sulated gripping surfaces when

performing work in which the

cutting tool may come into con-

tact with hidden wiring. Contact

with a live wire can also cause a

charge in metal parts of the device and

result in an electric shock.

• Fasten and secure the workpie-

ce by means of clamps or with

another method on a stable un-

derground. If you hold the workpiece

only with your hand or against your

own body, it will stay instable and this

can lead to a loss of control.

• Keep hands away from the

sawing area. Do not reach

underneath the workpiece. Al-

ways stand to the side of the

saw when working. Upon contact

with the blade there is a risk of injury.

• Only when the electric tool is

turned on should the sawing

blade be moved against the

workpiece. There is a risk of kickback

if the tool insert jams in the workpiece.

• Make sure that the footplate

is securely placed against the

workpiece during sawing. The

sawblade can tilt and lead to loss of

control over the power tool.

• 

the power tool off and do not

12

GB CY

pull the sawblade out of the cut

until it has come to a standstill.

In this way you will avoid any kickback

and can safely put down the power tool.

• Use only undamaged saw-

blades in perfect condition. Bent

or blunt blades can break, adversely

affect the cut or cause kickback.

• Do not brake the sawblade af-

ter switching the appliance off

by applying side pressure. The

sawblade may be damaged, break or

cause a kickback.

• 

not support the workpiece by

hand or foot. Do not touch any

objects or the ground with the saw run-

ning. There is a risk of kickback.

• Hold the power tool tightly with

both hands while working and

ensure a secure footing. The

power tool is guided more securely

with both hands.

• Wait until the power tool has

stopped before placing it down.

The tool insert can tilt and lead to loss

of control over the power tool.

• Switch the appliance off im-

mediately if the sawing blade

jams. Spread the saw cut out and pull

the blade out carefully. This can lead

to loss of control over the power tool.

3) SPECIAL SAFETY INFORMATION

DURING SANDING AND

SCRAPING

• Only use the power tool for dry

sanding. Do not scrape moist

materials. Penetration of water into

the power tool increases the risk of

electric shock.

• Avoid overheating the sanded

object and the sander itself. Pos-



• The workpiece gets hot dur-

ing grinding. Do not touch the

machined area, allow it to cool

down. There is a risk of burning. Do

not use coolants or the like.

• Always empty the dust con-

tainer before work breaks.

Sanding dust in the dust sack, micro





under unfavourable conditions such



metals. Particular hazards are caused

if the sanding dust is mixed with paint,

polyurethane residues or other chemi-

cal substances, or if the sanded object

is hot after long working periods.

4) SAFETY INFORMATION FOR

USING LONG DRILLS

a) Do not work at a speed higher

than the maximum permissible

speed for the drill. Higher speeds

can cause the drill to bend slightly

when rotating freely without contact

with the workpiece and can also cause

injury.

b) Always begin drilling at a low

speed and when the drill is in

contact with the workpiece. Hig-

her speeds can cause the drill to bend

slightly when rotating freely without

contact with the workpiece and can

also cause injury.

c) Do not apply excessive pressu-

re to the drill. Drills can bend and

break or cause a loss in control, thus

resulting in injuries.

13

CYGB

5) RESIDUAL RISKS



electric tool, some residual risks will remain.

Due to its construction and build, this elec-

tric tool may present the following hazards:

a) Lung damage, if suitable respiratory

protection is not worn;

b) Cuts

 

protection.

 

is not worn.

e) Damage to your health caused by

swinging your hands and arms when

operating the appliance for longer pe-

riods of time or if the unit is not held or

maintained properly.

Warning! During operation, this

electric tool generates an electro-



circumstances, may impair the func-

tionality of active or passive medical

implants. To reduce the risk of seri-

ous or lethal injuries, we recommend

that persons with medical implants

consult their doctor and the manu-

facturer of their medical implant

before operating the machine.

Observe the safety informati-

on and notes on charging and

proper use as shown in the

instruction manual for your

battery and charger from the



A detailed description of the

charging process and further

information can be found in

the separate operating inst-

ructions.

Do not use any accessories that are not

recommended by PARKSIDE. This can result



Practical tips

When working with the ap-

pliance, always wear suita-

ble clothing and appropriate

protective equipment.

Prior to each use it must be

ensured that the appliance is

working correctly.

Personal protective equip-

ment and a fully functional

appliance reduce the risk of

injuries and accidents.

Ensure that the ambient tem-

perature does not exceed



during work.

Wear ear protection.

Operation

Replacing the appliance at-

tachment

Secure the appliance against

switching on (see “Switch-

ing on/off”) or remove the

rechargeable battery from

the appliance. There is an

injury hazard if the device is

switched on accidentally.

Wear safety gloves. The appliance

attachment might have heated up

after use.

14

GB CY

Removing appliance attachment

1. Push the unlocking lever (5) into posi-

tion as far as the stop and then

hold it in this position.

2. Pull the unlocked appliance attachment

off (4/16/22/26).

Fitting appliance attachment

3. Push the appliance attachment

(4/16/22/26) along the guide rail

into the motor unit (6).

4. Allow the unlocking lever (5) to slide

back into position .

5. Check that the appliance attachment is

secure by pulling on it.

Inserting/removing

thebattery

1. To remove the battery (9) from the de-

vice, press both release buttons (9b) on

the battery and pull the battery out.

2. To insert the battery (9), push the bat-

tery along the guide rail into the de-

vice. You will hear it click into place.

Only insert the rechargeable

battery once the device is

completely assembled. Risk

of injury!

Switching on/off

1. Switching on: Press the on/off switch

(10).

By using the on/off switch (10) you

can progressively control the speed.

Gentle pressure: low speed

Increase pressure: higher speed.

2. Switching off: Release the on/off

switch (10).

If you place the direction switch

(7) in the middle position, the device is

secured against being switched on.

Checking the battery

chargelevel

The battery’s (9) charge level is indicated

by the charge state indicator (9a).

• The charge level of the battery is

indicated by illumination of the corre-



in operation. Press and hold the power

button to view.

red-yellow-green => Battery fully charged

red and yellow => Battery half charged

red => Battery needs

to be charged

Charge the battery (9) when only



illuminated.

Recharging the battery

Allow a hot battery to cool before

charging.

Only charge the battery (9) when



indicator (9a) is on.

1. Remove the battery (9) from the appli-

ance, as necessary (see „Removing/

inserting the battery“).

2. Insert the battery (9) in the charging

compartment of the battery charger

(14).

3. Plug the battery charger (14) into a

mains outlet.

4. When the battery is fully recharged un-

plug the battery charger (14) from the

mains.

5. Remove the battery (9) from the charg-

er (14).

15

CYGB

Overview of the control display on

the charger (14):

Green LED lights up without battery in-

serted: Charger ready.

Green LED lights up: Battery such alleged

charged.

Red LED lights up: Battery charging.

Motor unit with drill

attachment PKGA1

Changing the tool

Secure the appliance against

switching on (see “Switch-

ing on/off”). If the appliance

is switched on accidentally,

there is a danger of injury.

1. Rotate the keyless chuck (1) towards

RELEASE

until the drill chuck aperture is

large enough to accommodate the tool.

2. Insert the tool as far as possible into

the keyless chuck (1).

3. Turn the keyless chuck towards

GRIP

in

order to clamp the tool.

4. To remove the tool again, rotate the

keyless chuck (1) towards

RELEASE

until

the drill chuck aperture is large enough

to remove the tool.

Choice of gear

Stop appliance before

changing gear.

1. Wait for the appliance to come to a

standstill.

2 Slide the gear selector (3) into the re-

quired position:

1: 0-400 min-1

2: 0-1350 min-1

Set the direction of rotation

The appliance’s direction of rotation can

be changed with the rotational direction

switch.

The arrow on the direction switch indicates

the working direction.

1. Wait for the appliance to come to a

standstill.

2. Push the rotational direction speed

(7) into the desired position:

To drill and screw in screws: Press the

direction switch with the arrow poin-

ting forwards

To unscrew screws: Press the direction

switch with the arrow pointing back-

wards

3. If you place the direction switch

(7) in the middle position, the device is

secured against being switched on.

The direction change may only be

actuated when at a standstill!

Torque adjustment

You can preselect the maximum torque.

The torque settings are labelled 1 - 19 +

1. Wait for the appliance to come to a

standstill.

2. Turn the torque adjusting ring (2) to

select the desired torque:

Screws: Steps 1 - 19

Drilling: Step

3. Start with a lower torque step and

increase as required.

The direction change may only be

actuated when the appliance is at a

standstill!

16

GB CY

The necessary torque is dependent on:

- the type and hardness of the ma-

terial to be treated;

- the type and length of the screws

used.

Motor unit with

multisander

attachment PKGA2

Secure the appliance against

switching on (see “Switch-

ing on/off”). If the appliance

is switched on accidentally,

there is a danger of injury.

Wear a protective mask during

grinding work.

Attaching/removing sanding

sheet



for

rapid attachment of the sanding sheet.

Attaching sanding sheet

1. Press the sanding sheet (23) evenly onto



holes in the sanding sheet are placed

above the openings in the sanding plate.

Removing sanding sheet

2. Simply pull the sanding sheet (23) off

the sanding plate (21).

Connecting dust extraction

You can reduce dust production during sand-

ing by attaching a dust extraction system.

1. Push the adaptor (24) into the opening

on the multi-sander attachment (22) as

far as the stop.

2. Connect a dust extractor suction hose

to the adaptor (24).

Make sure that the dust extraction sys-

tem is suitable for the material to be

cut. This information can be found in

the operating instructions of the exter-

nal device.

If necessary, you can connect the suc-

tion hose of a vacuum cleaner with-

out reducer (25) to the adapter (24).

Sanding

• Use a dust extraction system when sand-

ing with the multi-sander attachment.

• Move the appliance against the work-

piece once it is switched on.

• Clean the sanding plate before you at-

tach a sanding sheet.

• Only work with sanding sheets in per-

fect condition to achieve good sanding

results.

• Work using low and even pressure.

This protects the appliance and the

sanding sheet.

• Do not use the same sanding sheet to

sand different materials (e.g. metal

and then wood).

Selection of sanding sheet

Grain size P Application

P 60 for pre-sanding rough wood

surfaces

P 80 / 120 for plain sanding

P 240 

and painted surfaces

17

CYGB

Motor unit

with sabre saw

attachment PKGA3

Installing/changing the blade

Secure the appliance against

switching on (see “Switch-

ing on/off”). If the appliance

is switched on accidentally,

there is a danger of injury.

Wear gloves when handling the

sawblade. In this way, you avoid

injury from cuts.

Caution, risk of Injury!

- Do not use any blunt or bent

blades or blades which are

damaged in any other way.

- Always insert a suitable saw-

blade.

An overview of appropriate blades

can be found in “Spare Parts/Ac-

cessories”.

Installing the blade:

1. Push the lever (18) for sawblade un-

locking downwards as far as the stop

and keep it held down. Push the saw-

blade shaft (19/20) into the sawblade

mounting slot.

2. To unlock, release the lever (18), it will

return to the initial position.

3. Check that the sawblade is secure by

pulling on it.

Removing the sawblade:

4. Press the lever (18) for sawblade un-

locking downwards as far as the stop

and then pull the sawblade out of the

sawblade mounting.

For certain work, the sawblade

can also be inserted after turning



Operating the sabre saw

1. Before switching the appliance on, en-

sure it is not in contact with the work-

piece.

2. Turn the appliance on.

By using the on/off switch (10) you can

progressively control the stroke rate.

Gentle pressure: low stroke rate.

Greater pressure: higher stroke rate.

The on/off switch cannot be locked.

3. Place the footplate (17) on the work-

piece.

4. Cut with a uniform forward motion.

 

switch off the device and then remove

the blade from the saw cut.

Sawing

Wear eye protection.

• Use only undamaged sawblades in

perfect condition. Only use metal saw-

blades for metalworking.

 

the appliance tightly with both hands

and away from your body.

• Before sawing the workpiece, check

for hidden foreign objects such as

nails, screws. These must be removed.

• Plunge cuts may only be made in soft

material such as wood or plaster-

board.

Plunge cuts

Risk of kickback! Hold the



18

GB CY

1. Place the device with the bottom edge

of the footplate (17) on the workpiece.

2. Turn on the device.

3. Insert the saw blade (20) in the workpi-

ece by tipping the device forward until

the device is vertical.

4. Continue sawing along the desired cut-

ting line.

Selection of sawblade

Wood sawblade for wood, plastic, plaster-

board

Metal sawblade 

and tubes

Plunge sawblade for soft materials like

wood or plasterboard

Motor unit with

multifunction tool

PKGA4

Wear a protective mask during

grinding work.

Changing the tool

Secure the appliance against

switching on (see “Switch-

ing on/off”). If the appliance

is switched on accidentally,

there is a danger of injury.

 

tightly screwed in to ensure you can

safely mount and use all the sup-

plied tools (30/32/33).

1. Push the lever (27) for tool unlocking

upwards as far as the stop.

2. Place the desired tool (30/32/33) be-

low the tool holder (29) on the arbors

(28). You may need to rotate the un-

locked tool holder (29) as far as need-

ed to allow you to place the desired

tool (30/32/33) onto the arbors (28).

12 different positions are possible.

3. Rotate the tool holder as required until



4. Push the lever (27) for tool unlocking

forwards again. The tool holder is



Attaching/removing sanding

sheet





sheet.

Attaching sanding sheet

1. Press the sanding sheet (31) evenly

-

sure that the holes in the sanding sheet

are placed above the openings in the

sanding plate.

Removing sanding sheet

2. Simply pull the sanding sheet (31) off

the delta sanding plate (30).

Sanding

• Move the appliance against the work-

piece once it is switched on.

• Clean the sanding plate before you at-

tach a sanding sheet.

• Only work with sanding sheets in per-

fect condition to achieve good sanding

results.

• Work using low and even pressure.

This protects the appliance and the

sanding sheet.

• Do not use the same sanding sheet to

sand different materials (e.g. metal

and then wood).

19

CYGB

Selection of sanding sheet

Grain size P Application

P 60 for pre-sanding rough wood

surfaces

P 80 / 120 for plain sanding

P 240 

and painted surfaces

Scraping

• Use a high oscillation rate when scrap-

ing.

• Work using low pressure and at a low

angle in order not to damage the sub-

strate material.

Cleaning/Maintenance

Repair and servicing work not

described in this manual should

always be carried by our Service

Centre. Use only original parts.

Switch off the device and remove

the battery from the device before

working with or transporting it.

The following cleaning and servicing

should be done regularly. This will ensure

a long and reliable service life.

Cleaning

Do not spray the appliance

with water and do not im-

merse it in water. Electric

shock hazard!

 

housing and handles of the appliance.

Use a damp cloth or a brush.

Do not use cleaning agents or solvents.

You may otherwise irreparably dam-

age the appliance.

Maintenance

• The equipment is maintenance free.

Storage

• Store the device in a dry place well out

of reach of children.

 



cold or heat so the battery does not

lose power.

• Remove the battery before storing the

unit for longer periods of time.

• Store the battery only in a partially

charged state. The state of charge

should be 40 – 60 % over a longer



charge status display ( 9a) illumi-

nate).

• During a longer storage period, check

the state of charge of the battery and

recharge if necessary roughly every



Waste Disposal/Envi-

ronmental Protection

Remove the battery from the device and

take the device, battery, accessories and

packaging for environmentally friendly

recycling. Instructions on how to dispose

of the rechargeable battery can be found

in the separate instruction manual for your

battery and charger.

 

domestic waste.

20

GB CY

• Remove the rechargeable battery be-

fore disposing of the appliance.

• Return the unit and the recharger to a

recycling centre. The plastic and metal

parts employed can be separated out

and thus recycled use can be imple-

mented. Ask our Service-Center for

details.

• Defective units returned to us will be

disposed of for free.

Guarantee

Dear Customer,

This equipment is provided with a 3-year

guarantee from the date of purchase.

In case of defects, you have statutory rights

against the seller of the product. These

statutory rights are not restricted by our

guarantee presented below.

Terms of Guarantee

The term of the guarantee begins on the

date of purchase. Please retain the original

receipt. This document is required as proof

of purchase.

If a material or manufacturing defect

occurs within three years of the date of

purchase of this product, we will repair or

replace – at our choice – the product for

you free of charge. This guarantee requires

the defective equipment and proof of pur-

chase to be presented within the three-year

period with a brief written description of

what constitutes the defect and when it oc-

curred.

If the defect is covered by our guarantee,

you will receive either the repaired product

or a new product. No new guarantee pe-

riod begins on repair or replacement of the

product.

Guarantee Period and Statutory

Claims for Defects

The guarantee period is not extended by

the guarantee service. This also applies for

replaced or repaired parts. Any damages

and defects already present at the time of

purchase must be reported immediately af-

ter unpacking. Repairs arising after expiry

of the guarantee period are chargeable.

Guarantee Cover

The equipment has been carefully pro-

duced in accordance with strict quality

guidelines and conscientiously checked

prior to delivery.

The guarantee applies for all material and

manufacturing defects. This guarantee

does not extend to cover product parts that

are subject to normal wear and may there-

fore be considered as wearing parts (e.g.

tools) or to cover damage to breakable

parts (e.g. switches).

This guarantee shall be invalid if the prod-

uct has been damaged, used incorrectly or

not maintained. Precise adherence to all of



manual is required for proper use of the

product. Intended uses and actions against

which the operating manual advises or

warns must be categorically avoided.

The product is designed only for private

and not commercial use. The guarantee

will be invalidated in case of misuse or

improper handling, use of force, or inter-

ventions not undertaken by our authorised

service branch.

Pagina se încarcă ...

Parkside PKGA 20-Li C2 Manual de utilizare

Parkside PKGA 20-Li C2 Manual de utilizare

Lucrări conexe

Alte documente