Parkside PFBS 9.6 A1 Operation and Safety Notes

IAN 90550

CORDLESS MULTIGRINDER PFBS 9.6 A1

AKKU-FEINBOHRSCHLEIFER

Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung

MAȘINĂ FINĂ DE GĂURIT ȘI

ȘLEFUIT CU ACUMULATOR

Instrucţiuni de utilizare şi de siguranţă

Traducerea instrucţiunilor de utilizare originale

АКУМУЛАТОРНА ФИНА БОРМАШИНА

Инструкции за обслужване и безопасност

Превод на оригиналното ръководство за експлоатация

CORDLESS MUL TIGRINDER

Operation and Safety Notes

Translation of original operation manual

GB Operation and Safety Notes Page 5

RO Instrucţiuni de utilizare şi de siguranţă Pagina 19

BG Инструкции за обслужване и безопасност Страница 33

DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 47

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the

device.

Înainte de a citi instrucţiunile, priviţi imaginile şi familiarizaţi-vă cu toate funcţiile aparatului.

Преди да прочетете отворете страницата с фигурите и след това се запознайте с всички функции

на уреда.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

6

4

8

3

7

D

E

F

G H

18

4 a

3 a

1 2

5

A

11

9

10

CB

16

14

15

19

22

20

21

12

23

13

18

17

5 GB

Table of contents

Introduction

Proper use ............................................................................................................................................Page 6

Features and equipment .....................................................................................................................Page 6

Included items .....................................................................................................................................Page 6

Technical information .......................................................................................................................... Page 6

General safety advice for electrical power tools

1. Workplace safety ...........................................................................................................................Page 7

2. Electrical safety ............................................................................................................................... Page 7

3. Personal safety ................................................................................................................................Page 8

4. Careful handling and use of electrical power tools .....................................................................Page 8

5. Use and handling of the cordless electrical power tool ..............................................................Page 9

6. Service .............................................................................................................................................Page 9

Safety advice for all uses ....................................................................................................................Page 9

Safety advice relating to kickback .....................................................................................................Page 10

Special safety advice relating to grinding and disc-cutting ..............................................................Page 11

Further special safety advice for disc-cutting ..................................................................................... Page 11

Special safety advice for abrading using sandpaper ......................................................................Page 12

Special safety advice for polishing ....................................................................................................Page 12

Special safety advice for working with wire brushes ........................................................................Page 12

Safety advice applicable specifically to cordless multigrinders .......................................................Page 12

Operation

Charging the battery pack .................................................................................................................Page 13

Inserting / removing the battery pack into / out of the drill / grinder ................................................Page 13

Reading off the battery status .............................................................................................................Page 13

Inserting or replacing a tool / collet ................................................................................................... Page 14

Switching on and off / Setting the speed range ................................................................................Page 14

Advice on working with materials / Tools / Speed ranges ...............................................................Page 14

Tips and tricks ...................................................................................................................................... Page 15

Maintenance and cleaning

Maintenance .......................................................................................................................................Page 15

Cleaning ..............................................................................................................................................Page 15

Service ...............................................................................................................................................Page 15

Warranty .........................................................................................................................................Page 15

Disposal ............................................................................................................................................Page 16

Declaration of conformity / Manufacturer ..........................................................Page 17

6 GB

Introduction

Introduction / General safety advice for electrical power tools

Cordless multigrinder PFBS 9.6 A1

Q

Introduction

We congratulate you on the purchase of your new

device. You have chosen a high quality product. The

instructions for use are part of the product. They

contain important information concerning safety,

use and disposal. Before using the product, please

familiarise yourself with all of the safety information

and instructions for use. Only use the unit as de

scribed

and for the speciﬁed applications. If you pass the

product on to anyone else, please ensure that you

also pass on all the documentation with it.

Q

Proper use

The rechargeable precision rotary tool with the cor-

responding accessory (as supplied) is intended to

be used for drilling, milling, engraving, polishing,

cleaning, grinding, cutting and sawing materials

such as wood, metal, plastic, ceramics or stone in

dry environments. Any other use or modiﬁcation to

the drill / grinder shall be considered as improper

use and could give rise to considerable dangers.

The manufacturer will not accept liability for loss or

damage arising from improper use. Not intended

for commercial use.

Q

Features and equipment

Cordless multigrinder:

1

Rotational speed control

2

Battery-operated LED

3

Battery pack release button

3 a

Battery pack

4

Metal stirrup hanger

4 a

Wrist strap

5

ON / OFF switch

6

Clamping nut

7

Spigot nut

8

Spindle lock

Battery charger (see Fig. A):

9

Charging cradle

10

Mains adapter

11

LED

Accessories (see Fig. B):

12

6 HSS drills

13

2 Mandrels for mounting tools

14

3 Polishing wheels

15

4 Grinding wheels

16

1 Metal brush

17

16 Cutting wheels

18

5 Collets

19

2 Plastic brushes

20

3 Engraving bits

21

2 Milling bits

22

5 Grinding bits

23

Combination tool

Q

Included items

1 Cordless multigrinder with rechargeable

battery pack

1 Charging cradle

1 Mains adapter

1 Accessory kit (50-piece)

1 Operating instructions

Q

Technical information

Model PFBS 9.6 A1:

Rated voltage: 9.6 V

Rated speed: n 5000–25000 min

-1

Max. disc ø: 25 mm

Collet capacity: max. ø 3.2 mm

Rechargeable battery pack PFBS 9.6 A1-1:

Rated voltage: 9.6 V

Capacity: 1000 mAh NiMH

Battery charger PFBS 9.6 A1-2:

Primary:

Rated voltage: 230–240 V∼, 50 Hz

Rated input: 13 W

7 GB

Introduction

Introduction / General safety advice for electrical power tools

Secondary:

Rated voltage: 12 V

Charging current: 400 mA

Charging duration: approx. 3 hours

Protection class: II /

Noise and vibration data:

Measured values for noise are determined in accor-

dance with EN 60745. The A-weighted noise level

of the electrical power tool are typically:

Sound pressure level: 70.4 dB(A)

Sound power level: 81.4 dB(A)

Uncertainty K: 3 dB

Wear ear protection!

Evaluated acceleration, typical:

Hand / arm vibration: 0.759 m / s

2

Uncertainty K = 1.5 m / s

2

The vibration level speciﬁed in

these instructions was measured in accordance with

an EN 60745 standardised measurement process

and can be used to compare equipment. The vibra-

tion emission value speciﬁed can also serve as a

preliminary assessment of the exposure.

The vibration level will change according to the ap-

plication of the electrical tool an in some cases may

exceed the value speciﬁed in these instructions. Re-

gularly using the electric tool in such a way may

make it easy to underestimate the vibration.

Note: If you wish to make an accurate assessment

of the vibration loads experienced during a particular

period of working, you should also take into account

the intervening periods of time when the device is

switched oﬀ or is running but is not actually in use.

This can result in a much lower vibration load over

the whole of the period of working.

Q

General safety advice for

electrical power tools

Read all the

safety advice and instructions!

Failure to observe the safety advice

and instructions may result in electric shock, ﬁre

and / or serious injury.

Keep all the safety advice and instructions

in a safe place for future reference!

The term “electrical tool” used in the safety advice

refers to electrical tools powered by mains electricity

(by means of a mains lead) and electrical tools pow-

ered by rechargeable batteries (without a mains lead).

1. Workplace safety

a) K

eep your working area clean and wel

l

lit. Untidy or poorly lit working areas can lead

to accidents.

b) Do not work with the device in poten-

tially explosive environments in which

there are inflammable liquids, gases o

r

dusts. Electrical power tools create sparks,

which can ignite dusts or fumes.

c) Keep children and other people away

while you are operating the electrical

tool. Distractions can cause you to lose con-

trol of the device.

2. Electrical safety

a) The mains plug on the power tool (or

on the power supply) must ﬁt the

mains

socket. Never modify the plug in any

way. Never use adapter plugs with

earthed power tools. Unmodiﬁed plugs

and the correct sockets reduce the risk of elec-

tric shock.

b) Avoid touching earthed surfaces such

as pipes, radiators, ovens and refrig-

erators with any part of your body.

There is an increased risk of electric shock if

your body is earthed.

8 GB

General safety advice for electrical power tools

c) Keep the device away from rain or

moisture. Water entering an electrical device

increases the risk of electric shock.

d) Do not use the mains lead for any pur-

pose for which it was not intended, e.

g.

to carry the device, to hang up the de-

vice or to pull the mains plug out of

the mains socket. Keep the mains lead

away from heat, oil, sharp edges or

moving parts of the device. Damaged or

tangled mains leads increase the risk of elec-

tric shock.

e) When working outdoors with an elec-

trical power tool always use extension

cables that are also approved for use

outdoors. The use of an extension cable suit-

able for outdoor use reduces the risk of elec-

tric shock.

f) Use a residual current device (RCD) for

protection if operating the electrical

power tool in a moist environment is

unavoidable. The use of an RCD reduces

the risk of electric shock.

3. Personal safety

a) Remain alert at all times, watch what

you are doing and always proceed

with caution. Do not use the device if

you are tired or under the influence of

drugs, alcohol or medication. One mo

ment

of carelessness when using the device can lead

to serious injury.

b) Wear personal protective equipment

and always wear safety glasses. The

wearing of personal protective equipment such

as dust masks, non-slip safety shoes, safety hel-

mets or ear protectors, appropriate to the type

of electrical power tool used and work under-

taken, reduces the risk of injury.

c) Avoid accidental starting. Verify the po-

wer tool is switched oﬀ before connec-

ting it to the mains and / or connecting

the battery, picking it up, or carrying it.

Accidents can happen if you carry the device

with your ﬁnger on the ON / OFF switch or with

the device switched on.

d) Remove any setting tools or spanners

before you switch the device on. A tool

or spanner left attached to a rotating part of a

device can lead to injury.

e) Avoid placing your body in an unnat-

ural position. Keep proper footing and

balance at all times. By doing this you will

be in a better position to control the device in

unforeseen circumstances.

f) Wear suitable clothing. Do not wear

loose clothing or jewellery. Keep your

hair, clothing and gloves clear of mov-

ing parts. Loose clothing, jewellery or long

hair can become trapped in moving parts.

g) If vacuum dust extraction and collection

devices are fitted do not forget to

check

that they are properly connected and

correctly used. The use of these devices

reduces the hazard presented by dust.

4. Careful handling and use

of electrical power tools

a) Do not overload the device. Always

use an electrical power tool that is

intended for the task you are under-

taking. By using the right electrical power

tool for the job you will work more safely and

achieve a better result.

b) Do not use an electrical power tool if

its switch is defective. An electrical power

tool that can no longer be switched on and oﬀ

is dangerous and must be repaired.

c) Pull the mains plug out of the socket

and / or remove the rechargeable bat-

tery before you make any adjustments

to the device, change accessories or

when the device is put away. This pre-

caution is intended to prevent the device from

unintentionally starting.

d) When not in use always ensure that

electrical power tools are kept out of

reach of children. Do not let anyone

use

the device if he or she is not familiar

with it or has not read the instructions

and advice. Electrical power tools are dan-

9 GB

General safety advice for electrical power tools

gerous when they are used by inexperienced

people.

e) Look after the device carefully. Check

that moving parts are working prop-

erly and move freely. Check for any

parts that are broken or damaged

enough to detrimentally affect the

functioning of the device. Have dam-

aged parts repaired before you use

the device. Many accidents have their origins

in poorly maintained electrical power tools.

f) Keep cutting tools clean and sharp.

Carefully maintained cutting tools with sharp

cutting edges are less likely to jam and are

easier to control.

g) Use the electrical power tool, accesso-

ries, inserted tools etc. in accordance

with these instructions and advice, and

the stipulations drawn up for this par-

ticular type of device. In doing this, take

into account the working conditions

and the task in hand. The use of electrical

power tools for purposes other than those in-

tended can lead to dangerous situations.

5. Use and handling of the cord-

less electrical power tool

a) Charge a rechargeable battery unit

using only the charger recommended

by the manufacturer. Chargers are often

designed for a particular type of rechargeable

battery unit. There is the danger of ﬁre if other

types of rechargeable battery units are used.

b) Only the rechargeable battery units

supplied are to be used with an elec-

trical power tool. The use of other recharge-

able battery units may lead to the danger of

injury or ﬁre.

c) When they are not being used, store

rechargeable battery units away from

paperclips, coins, keys. nails, screws

or other small metal objects that could

cause the contacts to be bridged. Short-

circuiting the contacts of a rechargeable battery

unit may result in heat damage or ﬁre.

d) Fluids may leak out of rechargeable

battery units if they are misused. If this

happens, avoid contact with the ﬂuid.

If contact occurs, ﬂush the aﬀected area

with water. Seek additional medical

help if any of the ﬂuid gets into your

eyes. Escaping battery ﬂuid may cause skin

irritation or burns.

CAUTION! DANGER OF EXPLOSION!

The batteries must never be recharged!

6. Service

a) Have your device repaired at the ser-

vice centre or by qualified specialist

personnel using original manufacturer

parts only. This will ensure that your device

remains safe to use.

Safety advice for all uses

General safety advice for grinding,

sanding (with sandpaper), wire brushing,

polishing and disc-cutting:

a) This electrical power tool is intended

for use as a grinding, sanding, wire-

brushing, and disc-cutting machine.

Observe all the safety advice, instruc-

tions, information in figures and all

other information you received with

this device. If you do not observe the follow-

ing advice it could lead to electric shock, ﬁre

and / or serious injury.

b) Normative statement / advice for this tool is not

applicable.

c) Do not use any accessory not specifi-

cally intended by the manufacturer

for this electrical power tool. Although

an accessory may ﬁt on your electrical power

tool, this does not on its own guarantee that it

can be safely used.

d) The maximum permitted speed of an

attachment must be at least as high as

the maximum speed indicated for the

electrical power tool. An accessory rotating

10 GB

General safety advice for electrical power tools

faster than its permitted speed could disintegrate

or ﬂy oﬀ.

e) The external diameter and the thickness

of the attachment must be compatible

with the dimensions of your electrical

power tool. Attachments that are not dimen-

sionally compatible cannot be adequately

guarded or controlled.

f)

Grinding discs, flanges, grinding wheels

or other accessories must fit exactly on

to the spindle of your electrical power

tool. Attachments that do not exactly ﬁt on the

spindle turn unevenly, vibrate severely and could

lead to loss of control.

g) Do not use damaged attachments.

Before every use check attachments

such as grinding discs for loose frag-

ments and cracks, grinding wheels for

cracks, deterioration or excessive

wear

and wire brushes for loose or broken

wires. If the electrical power tool or

attachment is dropped, inspect for

damage or change the attachment for

an undamaged one. When you have

inspected and inserted the attachment,

position yourself and bystanders away

from the plane of the rotating attach-

ment and run the device at maximum

speed for one minute. Damaged attach-

ments will usually break apart during this test.

h) Wear personal protective equipment.

Use a full face visor, safety goggles or

safety glasses, depending on the ap-

plication. Wear a dust mask, hearing

protectors, safety gloves or special

apron capable of stopping particles of

the grinding medium or workpiece,

as appropriate for the task. Eyes must

be protected from the ﬂying debris which can

arise from some operations. Dust or breathing

masks must be capable of ﬁltering out the dust

generated by the application. Prolonged expo-

sure to loud noise can lead to hearing loss.

i) Keep bystanders at a safe distance

from your work area. Anyone entering

the work area must wear personal

protective equipment. Fragments of the

workpiece or of a broken attachment could ﬂy

oﬀ and cause injury beyond the immediate

working area.

j) Hold the device by the insulated han-

dle surfaces when you are undertak-

ing work where there is the danger of

the attachment striking hidden electric-

ity cables or the device’s mains lead.

Contact with a live wire could cause metal parts

of the device to become live and lead to elec-

tric shock.

k) Keep the mains lead away from rotat-

ing attachments. If you lose control of the

device the mains lead may become severed or

trapped and your hand or arm may be pulled

into the rotating attachment.

l) Never lay the electrical power tool

down until after the attachment has

come to a complete standstill. The rotat-

ing attachment may snag when it comes into

contact with the surface and cause you to lose

control of the device.

m) Do not have the electrical power tool

running while you are carrying it. Your

clothing could become trapped by unintention-

al contact with the rotating attachment and the

tool could be pulled into your body.

n) Clean the ventilation slots on your

electrical power tool regularly. The mo-

tor’s fan draws dust into the housing. A build-up

of metal dust could give rise to an electrical

hazard.

o)

Never use the electrical power tool near

inflammable materials. Sparks could ignite

these materials.

p) Do not use attachments that require the

use of coolants. The use of water or other

liquid coolants could result in electric shock.

Safety advice

relating to kickback

Kickback is the sudden reaction to a pinched or

snagged rotating attachment, such as a grinding disc

,

grinding pad, wire brush etc. Pinching or snagging

results in the rotating attachment coming to an abrupt

stop. This causes the electrical power tool (if not

controlled) to move in the opposite direction to the

11 GB

General safety advice for electrical power tools

direction of rotation of the attachment at the point

of constraint.

If, for example, a grinding disc is pinched or snags

in a workpiece, this can cause the edge of the

grinding disc to penetrate the workpiece, become

trapped there and either free itself or kickback. The

grinding disc moves towards or away from the op-

erator, depending on the direction of movement of

the disc at the point of constraint. The grinding disc

could also break.

Kickback occurs as a result of incorrect use or mis-

use of the electrical power tool. It can be prevented

by taking the appropriate precautions as described

below.

a) Maintain a firm grip on the electrical

power tool and position your body

and arms to allow you to resist kick-

back forces. Always use the auxiliary

handle, if provided, to exercise the

greatest possible control over kick-

back forces or reaction torques as the

device builds up to full speed. By taking

suitable precautions the operator can control

kickback and reaction forces.

b) Do not place your hands near a rotat-

ing attachment. If kickback occurs the at-

tachment could move over your hand.

c) Avoid positioning your body in the

area into which the electrical power

tool would move in the event of a kick-

back. A kickback moves the electrical power

tool in the opposite direction to the direction of

movement of the grinding disc at the point of

constraint.

d) Work particularly carefully in the area

of corners, sharp edges etc. to avoid

the attachment bouncing or snagging

on the workpiece. Corners, sharp edges or

bouncing have a tendency to snag the rotating

attachment. This causes loss of control or kick-

back.

e) Do not use saw-chain woodcarving

discs or toothed discs. Such attachments

create frequent kickback and loss of control of

the electrical power tool.

Special safety advice relating

to grinding and disc-cutting

a) Always use the guard designed for the

type of abrasive consumable you are

using. Always use abrasive consuma-

bles approved for use with your elec-

trical power tool. Abrasive consumables not

approved for use with your electrical power tool

cannot be adequately guarded and are unsafe.

b) To ensure the highest level of opera-

tional safety, the disc guard cover must

be attached to the electrical power tool

and set in such a way that the smallest

possible area of the abrasive consum-

able is exposed to the operator. The disc

guard cover is there to protect the operator from

pieces breaking oﬀ and accidental contact with

the abrasive consumable.

c) Abrasive consumables must be used

only for their recommended purposes,

For example: never grind with the side

face of a cutting disc. Cutting discs are in-

tended for removing material using the edge

of the disc. Sideways forces on these abrasive

consumables can cause them to break.

d) Always use an undamaged mounting

flange of the correct size and shape

for your selected grinding disc. Suitable

ﬂanges support the grinding disc and reduce

the chance of it breaking. Flanges for cutting

discs are diﬀerent from the ﬂanges for other

abrasive discs.

e) Never use worn down abrasive con-

sumables intended for larger electrical

power tools. Abrasive consumables intended

for larger electrical power tools are not designed

for the faster rotational speeds of these smaller

electrical power tools and could break.

Further special safety

advice for disc-cutting

a) Avoid snagging the cutting disc and

do not use too much contact pressure.

Do not attempt to make excessively

deep cuts. Overloading the cutting disc in-

12 GB

General safety advice for electrical power tools / Operation

General safety advice for electrical power tools

creases the load and the tendency of the disc

to twist or snag in the cut, making kickback or

disc breakage more likely.

b) Avoid the area in front of or behind

the rotating cutting disc. If the cutting disc

is moving away from you at the point of con-

straint in the workpiece, then, in the event of

a kickback, the electrical power tool and the

rotating disc may be thrown towards you.

c) If the cutting disc jams or you stop

work for a while, switch the device

off and hold it until the disc comes to

a complete stop. Never attempt to

pull the still rotating cutting disc out of

the cut as this could cause kickback.

Determine and rectify the reason for the jamming.

d) Do not switch on the device if the cut-

ting disc is in the workpiece. Allow the

cutting disc to reach full speed before

carefully continuing with the cut. Oth-

erwise the disc could snag, jump out of the

workpiece or cause a kickback.

e) Support boards or workpieces whilst

cutting to reduce the risk of kickback

caused by a jammed cutting disc. Large

workpieces may bend under their own weight.

The workpiece must be supported to both sides

of the cutting disc and particularly near the

cutting disc and at the workpiece edge.

f) B

e particularly careful when pocket

cutting in existing walls or other areas

where you cannot see what you are cut

-

t

ing into. The cutting disc plunged into the surface

could cut through gas or water pipes, electricity

cables or other objects and cause kickback.

Special safety advice for

abrading using sandpaper

Do not use over-sized sanding sheets.

Follow the manufacturer’s recommen-

dations for sanding sheet size. Sanding

sheets that project beyond the backing pad

could cause injury in addition to jamming,

tearing of the sheet or kickback.

Special safety

advice for polishing

Do not use the polishing bonnet if it

has any loose parts, in particular the

fastening cords. Tuck the fastening cords

away or trim them. Loose fastening cords rotat-

ing with the attachment could catch your ﬁngers

or become trapped in the workpiece.

Special safety advice for

working with wire brushes

a) Bear in mind that wire brushes lose

pieces of wire during normal use. Do

not overload the wires by applying too

much pressure. Flying pieces of wire can very

easily penetrate thin clothing and / or skin.

b) Use a guard, if recommended, but

make sure that the wire brush does

not come into contact with the guard.

The diameters of disc brushes and cup brushes

can increase due to contact pressure and cen-

tripetal forces.

Q

Safety advice applicable specif-

ically to cordless multigrinders

When you use the drill / grinder wear the fol-

lowing protective equipment: safety glasses

and protective gloves.

CAUTION! RISK OF INJURY! The tool

continues to rotate after it has been switched

oﬀ! Avoid contact with rapidly rotating drill /

grinder components.

Securely support the work-

piece. Use clamps or a vice to grip the workpiece

ﬁrmly. This is much safer than holding it in your

hand.

RISK OF INJURY! Never

support yourself by placing your hands near or

in front of the device or the workpiece surface.

A slip can result in injury.

DANGER OF FIRE FROM FLYING

SPARKS!

Abrading metal creates ﬂying sparks. For this

reason, always make sure that nobody is placed

13 GB

General safety advice for electrical power tools / Operation

General safety advice for electrical power tools

in any danger and that there are no inﬂamma

ble

materials near the working area.

DUST HAZARD! Any

harmful / noxious dusts generated from machin-

ing represent a risk to the health of the person

operating the device and to anyone near the

work area.

Wear a dust mask!

NOXIOUS FUMES!

Ensure that there is adequate ventilation when

machining surfaces containing plastic or cov-

ered with paint, varnish etc.

Its use as a saw or the use of saw blades with

this device is prohibited.

Do not soak the materials or the surface you

are about to work on with liquids containing

solvents.

Avoid abrading paints containing lead or other

substances hazardous to health.

Do not machine materials containing asbestos.

Asbestos is a known carcinogen.

Avoid contact with moving sanding or grinding

tools.

Do not machine moist materials or damp sur-

faces.

NOTE! Do not allow the tool to come to a

standstill by overloading it!

RISK OF INJURY!

Switch the device oﬀ and allow it to come to a

standstill before you put it down.

Always keep the device

clean, dry and free of oil or grease.

Children or persons who lack the knowledge or

experience to use the device or whose physical,

sensory or intellectual capacities are limited

must never be allowed to use the device without

supervision or instruction by a person responsi-

ble for their safety. Children must never be

allowed to play with the device.

Q

Operation

Never use the device for a purpose for which it was

not intended or with non-original parts / accessories.

The use of tools or accessories other than those rec-

ommended in the operating instructions could lead

to you suﬀering an injury.

Q

Charging the battery pack

NOTE! A battery pack that has been unused for a

while or never been charged must be charged before

reuse or ﬁrst use. The battery pack requires about

3–5 cycles before it can reach its full charge. The

charging process takes about 180 minutes.

CAUTION! RISK OF INJURY!

Always pull

out the mains plug (

mains adapter

10

) before

you

insert the battery pack into or take it out of

the charger.

Connect the adapter

10

to a mains socket.

Insert the battery pack

3 a

into the charging

cradle

9

. This can only be inserted with the

correct polarity.

The LED

11

lights up green whenever the bat-

tery pack

3 a

is in the charging cradle

9

and

the adapter

10

is connected to a mains socket.

CAUTION! Do not charge a battery pack for

a second time in close succession. There is a

danger of overcharging the battery pack.

Q

Inserting / removing the

battery pack into / out of the

drill / grinder

Inserting the battery pack:

Set the ON / OFF switch

5

to position “0”.

Insert the battery pack

3 a

into the drill / grinder

until it engages.

Removing the battery pack:

Pressing the battery pack buttons

3

at the

sides at the same time allows you to remove

the battery pack

3 a

.

Q

Reading oﬀ the battery status

The status or residual power is indicated as follows

in the battery-operated LED

2

whenever the appli-

ance is switched on:

RED / ORANGE / GREEN = maximum charge / power

RED / ORANGE = medium-level charge / power

RED = weak charge – recharge battery

14 GB

Operation / Maintenance and cleaning / Service / Warranty

Operation

Q

Inserting or replacing

a tool / collet

Press the spindle lock

8

and keep it pressed.

Rotate the clamping nut

6

until the lock

engages.

Loosen the clamping nut

6

with the combina-

tion key

23

.

If a tool is already inserted, remove it.

First insert the tool you wish to use through the

clamping nut

6

before you insert it into the

collet

18

suitable for the tool shaft.

Press the spindle lock

8

and keep it pressed.

Insert the collet

18

into the threaded insert and

tighten the clamping nut

6

on the thread using

the combination key

23

.

NOTE: Use the screwdriver end of the combi-

nation key

23

to release or tighten the screw of

the mandrels

13

.

Q

Switching on and oﬀ / Setting

the speed range

Switching on / Setting the speed range:

Set the ON / OFF switch

5

to position “I”.

Set the rotational speed control

1

to a position

between „1“ and „MAX.“.

Switching oﬀ:

Set the ON / OFF switch

5

to position “0”.

Q

Advice on working with

materials / Tools / Speed ranges

Use the highest speed when working on steel

or iron with the milling bits.

Use a short trial on a test piece to determine the

optimum rotational speed range for working on

zinc, zinc alloy, aluminium, copper and lead.

Use the low speed range for working on plastics

and low-melting point materials.

Use high speeds on wood.

Use the medium speed range for cleaning,

polishing and buﬃng.

The following information shall be considered as

recommendatory only. Learn by practical experience

which tools and settings are the best for the materi-

als you work with.

Setting the appropriate speed

Symbols

Rotational

speed

control

1

Material

1–3

Plastics and low melting

point materials

6–7

Hardwood

4–5

Stone, Ceramics

Max

Steel

5

Softwood, metal

Examples of appropriate tool selection Function

Function Accessory Application

Drilling

HSS drill

12

Drilling wood (see Fig. C)

Milling

Milling bits

21

Various tasks, e.g. hollowing out, gouging,

shaping, grooving or slotting

Engraving

Engraving bits

20

Markings (see Fig. D)

15 GB

Function Accessory Application

Polishing,

derusting

CAUTION!

Use only the lightest

contact pressure of

the tool on the work

-

piece.

Metal brush

16

Derusting (see Fig. E)

Polishing wheel

14

Working on various metals and plastics, in

particular noble metals like gold or silver

(see Fig. F)

Cleaning

Plastic brush

19

E.g. cleaning complex plastic housings or the

area around a door lock

Metal brush

16

e.g. derusting (see Fig. E)

(The metal brush is softer than steel)

Grinding

Grinding wheels

15

,

grinding bits

22

Grinding of stone, precise tasks on hard materials,

such as ceramics or alloy steel (see Fig. G)

Cutting

Cutting discs

17

Cutting metal, plastic (see Fig. H)

Operation / Maintenance and cleaning / Service / Warranty

Operation

Q

Tips and tricks

If you use press too hard you run the risk of break-

ing the tool or damaging the workpiece. You will

achieve the best results by operating the tool at a

constant rotational speed and using a low contact

pressure on the workpiece.

Q

Maintenance and cleaning

Q

Maintenance

Before and after a prolonged period of

non-use fully charge the battery pack

3 a

.

Q

Cleaning

Clean all the dirt oﬀ the drill / grinder. Use a

dry cloth for cleaning.

Q

Service

Have your device

repaired at the service centre or by

qualified specialist personnel using

original manufacturer parts only. This

will ensure that your device remains safe to use.

If the plug or lead

needs to be replaced, always have

the replacement carried out by the

manufacturer or its service centre. This

will ensure that your device remains safe to use.

Q

Warranty

The warranty for this appliance is for 3

years from the date of purchase. The ap-

pliance has been manufactured with care

and meticulously examined before deliv-

ery. Please retain your receipt as proof

of purchase. In the event of a warranty

claim, please make contact by telephone

with our Service Department. Only in this

way can a post-free despatch for your

goods be assured.

The warranty covers only claims for material and

maufacturing defects, but not for transport damage,

for wearing parts or for damage to fragile compo-

nents, e.g. buttons or batteries. This product is for pri-

vate use only and is not intended for commercial use.

16 GB

Warranty / Disposal

The warranty is void in the case of abusive and im-

proper handling, use of force and internal tampering

not carried out by our authorized service branch. Your

statutory rights are not restricted in any way by this

warranty.

The warranty period will not be extended by repairs

made unter warranty. This applies also to replaced

and repaired parts. Any damage and defects extant

on purchase must be reported immediately after

unpacking the appliance, at the latest, two days after

the purchase date. Repairs made after the expiration

of the warranty period are subject to payment.

GB

Service Great Britain

Tel.: 0871 5000 720

(0,10 GBP/Min.)

e-mail: kom[email protected]

IAN 90550

Q

Disposal

The packaging comprises exclusively en-

vironmentally-friendly material. Dispose

of it in your local recycling containers.

Do not dispose of electrical

appliances with your domestic

waste!

According to the European Directive 2002 / 96 / EC,

concerning used electrical and electronic appliances

and its implementation in national law, superannu-

ated electrical appliances must be collected and

disposed of via an environmentally suitable recy-

cling facility.

Do not dispose of rechargeable

batteries with your household

refuse!

Defective or worn out rechargeable batteries must

be recycled according to Directive 2006 / 66 / EC.

Dispose of batteries and appliances over the existing

collection facilities.

Your local communal or municipal authorities can

provide information on how to dispose of the worn

out appliance.

Declaration of conformity / Manufacturer

17 GB

Declaration of conformity /

Manufacturer

We, KOMPERNASS HANDELS GMBH, the person

responsible for documents: Mr Semi Uguzlu, BURG-

STRASSE 21, 44867 BOCHUM, GERMANY, hereby

declare that this product complies with the following

standards, normative documents and EU directives:

Machinery Directive

(2006 / 42 / EC)

EU Low Voltage Directive

(2006 / 95 / EC)

Electromagnetic Compatibility

(2004 / 108 / EC)

RoHS Directive

(2011 / 65 / EU)

Applicable harmonized standards

EN 60745-1/A11:2010

EN 60745-2-1:2010

EN 60745-2-3:2011

EN 55014-1/A1:2009

EN 55014-2/A2:2008

EN 60335-2-29:2004+A2:10

EN 62233:2008

EN 60335-1:2002+A11, A1:04+A12,

A2:06+A13:08+A14:10+A15:11

EN 61000-3-2:2006/A2:2009

EN 61000-3-3:2008

Type / Appliance Designation:

Cordless multigrinder PFBS 9.6 A1

Date of manufacture (DOM): 06–2013

Serial number: IAN 90550

Bochum, 30.06.2013

Semi Uguzlu

- Quality Manager -

We reserve the right to make technical modiﬁcat

ions

in the course of further development.

Warranty / Disposal

Declaration of conformity / Manufacturer

18

Cuprins

19 RO

Cuprins

Introducere

Utilizare conform scopului .............................................................................................................. Pagina 20

Dotare .............................................................................................................................................. Pagina 20

Pachet de livrare ............................................................................................................................. Pagina 20

Specificaţii tehnice .......................................................................................................................... Pagina 20

Indicaţii generale de siguranţă pentru uneltele electrice

1. Siguranţa la locul de muncă ...................................................................................................... Pagina 21

2. Siguranţă electrică ...................................................................................................................... Pagina 21

3. Siguranţa persoanelor ................................................................................................................ Pagina 22

4. Utilizarea şi deservirea uneltei electrice .................................................................................... Pagina 22

5. Utilizarea şi deservirea uneltei cu acumulator .......................................................................... Pagina 23

6. Service ......................................................................................................................................... Pagina 23

Instrucţiuni de siguranţă pentru toate aplicaţiile ............................................................................ Pagina 23

Recul şi instrucţiuni de siguranţă corespunzătoare ....................................................................... Pagina 25

Instrucţiuni de siguranţă speciale pentru şlefuire şi tăiere ............................................................. Pagina 25

Alte instrucţiuni de siguranţă speciale pentru tăiere ..................................................................... Pagina 26

Instrucţiuni de siguranţă speciale pentru şlefuirea cu hârtie abrazivă ......................................... Pagina 26

Instrucţiuni de siguranţă speciale pentru polizare......................................................................... Pagina 26

Instrucţiuni de siguranţă speciale pentru lucrul cu periile de sârmă ............................................ Pagina 26

Indicaţii de siguranţă specifice maşinilor de şlefuit multifuncţionale cu acumulator ................... Pagina 27

Utilizare

Încărcare pachet acumulator ......................................................................................................... Pagina 27

Introducerea / scoaterea pachetului de acumulatoare din aparat .............................................. Pagina 28

Citire stare acumulator .................................................................................................................... Pagina 28

Utilizare / schimbare sculă / cleşte de prindere ............................................................................ Pagina 28

Pornire - şi oprire / reglare domeniu de turaţie .............................................................................. Pagina 28

Indicaţii referitoare la prelucrarea materialului / sculelor / domeniului de turaţie ...................... Pagina 28

Indicii şi trucuri ................................................................................................................................. Pagina 29

Curăţare şi întreţinere

Întreţinere ......................................................................................................................................... Pagina 29

Curăţare ........................................................................................................................................... Pagina 30

Service ........................................................................................................................................... Pagina 30

Garanţie ....................................................................................................................................... Pagina 30

Înlăturare .................................................................................................................................... Pagina 30

Declaraţie de conformitate / Producător .......................................................... Pagina 31

20 RO

Introducere / Indicaţii generale de siguranţă pentru uneltele electrice

Introducere

Mașină ﬁnă de găurit și șlefuit cu

acumulator PFBS 9.6 A1

Q

Introducere

V

ă felicităm pentru achiziţia aparatului dumneavoastră.

Aţi ales un produs de înaltă calitate. Manualul de

utilizare reprezintă o parte integrantă a acestui pro-

dus. Acesta conţine informaţii importante referitoare

la siguranţă, la utilizare şi la eliminarea ca deşeu.

Înainte de utilizarea acestui produs, familiarizaţi-vă

mai întâi cu instrucţiunile de utilizare şi de siguranţă.

Folosiţi produsul numai în modul descris şi numai în

domeniile de utilizare indicate. Predaţi toate docu-

mentele aferente în cazul în care înstrăinaţi produsul.

Q

Utilizare conform scopului

Maşina de şlefuit multifuncţională cu acumulatori,

cu accesoriile aferente, (aşa cum se livrează), se

foloseşte la găuritul, frezatul, gravatul, polizatul,

curăţatul, şlefuitul, debitatul şi tăiatul lemnului, me-

talului, plasticului, ceramicii sau pietrei în încăperi

uscate. Orice altă utilizare sau modiﬁcare a apara-

tului este considerată necorespunzătoare scopului

şi reprezintă pericole de accidente grave. Pentru

daunele cauzate de o utilizare necorespunzătoare

scopului, producătorul nu preia nicio responsabili-

tate. Nu este prevăzută pentru uzul comercial.

Q

Dotare

Mașină fină de găurit și șlefuit cu

acumulator:

1

Reglare turaţie

2

LED acumulator

3

Tastă de deblocare acumulator

3 a

Pachet acumulator

4

Mâner de metal

4 a

Buclă de mână

5

Întrerupător PORNIT- / OPRIT

6

Mandrină de strângere rapidă

7

Piuliţă olandeză

8

Blocare pivot

Aparat de încărcat acumulator (vezi fig. A):

9

Suport de încărcat

10

Bloc de alimentare de la reţea

11

LED

Accesorii (vezi fig. B):

12

6 Burghiu HSS

13

2 Dornuri de prindere pentru ﬁxarea sculelor

14

3 Discuri abrazive

15

4 Discuri de şlefuit

16

1 Perie de metal

17

16 Discuri de debitat

18

5 Cleşti de prindere

19

2 Perii din plastic

20

3 Bituri de gravat

21

2 Bituri de frezat

22

5 Bituri de şlefuit

23

Cheie universală

Q

Pachet de livrare

1 Mașină ﬁnă de găurit și șlefuit cu acumulator cu

pachet de acumulator

1 Suport de încărcat

1 Bloc de alimentare de la reţea

1 Set de accesorii (50 de piese)

1 Manual de utilizare

Q

Speciﬁcaţii tehnice

Model PFBS 9.6 A1:

Tensiune nominală: 9.6 V

Turaţia: n 5000–25000 min

-1

Diametru max. discuri ø: 25 mm

Zonă de strângere

mandrină de găurire: max. ø 3,2 mm

Pachet acumulator PFBS 9.6 A1-1:

Tensiune nominală: 9.6 V

Capacitate: 1000 mAh NiMH

Aparat de încărcat acumulator

PFBS 9.6 A1-2:

Primar:

Tensiune nominală: 230–240 V∼, 50 Hz

Încărcarea nominală: 13 W

Pagina se încarcă ...

Parkside PFBS 9.6 A1 Operation and Safety Notes

Parkside PFBS 9.6 A1 Operation and Safety Notes

în alte limbi

Lucrări conexe

Alte documente