Tiger PIE-A50W Instruction manuals

TigTyra

Bình Thủy Điện

Sổ tay hướng dẫn sử dụng

Cám ơn bạn đã mua sản phẩm này.

Hãy đọc tất cả thông tin trong sổ tay hướng dẫn sử dụng này trước khi sử dụng

sản phẩm. Hãy lưu giữ sổ tay này ở nơi thuận tiện để tham khảo sau này.

Electric Water Heater /Warmer

User Manual

For household use

Thank you for purchasing this product.

Read all the information in this user manual before using the appliance.

Keep this manual in a handy location for future reference.

ℬ䛕嶡㞻–

椋⿥㋌巏㉕廚”㣙⌙▥䠱⁔♮的⣕㉕ℬ䛕Ὸ⏺的

嶤₁偳枲嶨ⴹ㣙嶡㞻–的〣⭒✱↊䵎的ₒⅬ格㞣╯枲҉

䛢䊚㷡䚣

PIE-A50W

1

English

Contents

中文

Tiếng Việt

Ni dung

1 Important Safeguards .......................................3

2 Part Names and Accessories .................................7

3 Boiling Water ..............................................8

4 Dispensing Hot Water ...................................... 11

5 How to use Energy Saving Mode .............................12

6 Using the Power-Saving Timer ...............................13

7 Using the Kitchen Timer ....................................14

8 After Finishing Using the Heater ..............................15

9 Cleaning ................................................16

10 Troubleshooting ........................................... 18

1 安全注意事项 21

2 各部件名称和附件 25

3 烧水 26

4 按出水键倒出开水 29

5 设定节能功能 30

6 设定省电计时 31

7 设定厨房定时 32

8 不使用时倒除开水 33

9 进行清洗 34

10 认为发生故障时 36

1 Chú ý an toàn quan trng .................................................39

2 Tên b phn và Ph kin ..................................................43

3 Cách Nu Nưc Sôi ........................................................44

4 Cách rót nưc nóng .......................................................47

5

Cách s dng Ch đ tit kim đin ...............................................48

6 S dng Hn gi tit kim đin ............................................49

7 S dng ch đ Hn gi đun sôi ...........................................50

8 Sau khi s dng bình đun nưc ............................................51

9 Cách V Sinh Bình Thy Đin ..............................................52

10 Khc phc s c ..........................................................54

2

IMPORTANT SAFEGUARDS

1. Read all instructions.

2. Do not touch hot surfaces. Use handles or knobs.

3. To protect against electrical shock, do not immerse cord or plug in water or other liquid.

4. Close supervision is necessary when the appliance is used by or near children.

5. Unplug from outlet when not in use and before cleaning. Allow to cool before putting on or

taking off parts.

6. Do not operate the appliance with a damaged cord or plug or after the appliance

malfunctions or has been damaged in any manner. Return appliance to the nearest

authorized service facility for examination, repair, or adjustment.

7.

8. Do not use outdoors.

9. Do not let cord hang over edge of table or counter, or touch hot surfaces.

10.

Do not place the appliance on or near a hot gas or electric burner, or in a heated oven.

11. Extreme caution must be used when moving the appliance containing hot oil or other hot

liquids.

12.

13.

SAVE THESE INSTRUCTIONS

Servicing should be performed by an authorized service representative.

This appliance is intended for household use.

The following instructions are applicable to 120V only:

This appliance has a polarized plug (one blade is wider than the other). To reduce the risk

of electric shock, this plug is intended to fit into a polarized outlet only one way. If the

plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified

electrician. Do not attempt to modify the plug in any way.

Do not use the appliance for other than intended use.

When using the appliance, basic safety precautions should always be followed including

the following:

Always attach plug to the appliance first, then plug cord into the wall outlet.

To disconnect, turn any control to "off", then remove plug from wall outlet.

The appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been

given supervision or instruction concerning use of the appliance by a person responsible for

their safety.

Children should be supervised to ensure that they do not play with the appliance.

The use of accessory attachments not recommended by the appliance manufacture may

result in fire , electric shock or injury to persons.

To reduce the risk of injury , do not drape cord over the counter top or table top where it

can be pulled on by children or tripped over unintentionally.

3

Do not let infants or

children lick the electric

sockets or fixtures.

Doing so may result in

electric shock.

Attach the lid tightly until a “clicking”

sound is heard.

If lid is not attached properly water may

boil over or spill if tipped, which may cause

scalds.

1 Important Safeguards

Read carefully before using and be sure to follow the instructions.

The WARNINGS and CAUTIONS described below are intended to protect the user and other

individuals from physical harm and household damage. To ensure safety, please follow carefully.

Do not remove the caution/warning seal attached to the appliance.

Safety instructions are classified and described

according to the level of harm and damage caused

by improper use, as shown below.

This symbol indicates there is a

possibility of death or serious injury*1

when the unit is improperly handled.

This symbol indicates there is a

possibility of injury*2 or damage*3 to

property when the unit is improperly

handled.

*1

"Seriously injury" is defined here as loss of sight, burns (high and low

temperature), electric shock, broken bones, poisoning, or other injuries severe

enough to require hospitalization or extended outpatient care.

*2

"Minor or moderate injury" is defined here as a physical injury, burn, or electric

shock which will not require hospital stay or extended outpatient care.

*3

"

Damage to property" is defined here as damage towards a building, furniture, or pets.

Warning

Caution

Description of Symbols

The symbol indicates a

warning or caution. The specific

details of the warning or caution are

indicated inside the symbol or in an

illustration or text near the symbol.

The symbol indicates a

prohibited action. The specific

details of the prohibited action are

indicated inside the symbol or in an

illustration or text near the symbol.

The symbol indicates an

action that must be taken or an

instruction that must be followed.

The specific details of the action

or instruction are indicated inside

the symbol or in an illustration or

text near the symbol.

Caution

Prohibited

Instructions

Extra attention must be paid when used in a household where infants or toddlers are present.

Warning

Caution

Do not allow children to use the

appliance by themselves and do not

put within reach of infants or toddlers.

Failing to do so may result in burns,

electric shock, or injury.

This appliance is not intended for

use by persons (including children)

with physical difficulties or lack of

experience and knowledge - unless

they have been given supervision or

instruction concerning to the use of the

appliance by a person responsible for

his/her safety.

Do not use on an unstable surface, or on

a table or rug that is vulnerable to heat.

If the kettle tips over, water may spill, which

may cause scalds. Fire or damage to the

table or surrounding materials may result.

English

4

Warning

Do not attempt to disassemble, repair,

or modify the product. Repairs should

only be performed by a qualified service

representative.

Doing so may result in fire, electric shock, or

injur y.

Use a 220V AC power source.

Use of any other power supply voltage may

result in fire or electric shock.

Use an electrical outlet rated 7A or higher

and do not plug in other devices at the

same time.

Connecting other devices in the same outlet

may cause the outlet to overheat or result in

fire.

Do not damage or use a damaged power

cord. Do not forcefully bend, twist, fold, or

modify the cord. Do not place near high

temperature surfaces or under/between

heavy objects.

A damaged power cord can cause fire or

electric shock.

Wipe the plug thoroughly in the case dust

or other foreign objects are collected.

This is to avoid fire.

Firmly insert the plug into the outlet to

avoid electric shock, shorting, smoke, or

fire.

Do not use the product if the power cord

or plug is damaged or the plug is loose in

the outlet. This is to avoid electric shock

shorting, or fire.

If the supply cord is damaged, it must be

replaced by a special cord or assembly

available from the manufacturer or its

service agent.

Do not plug in or unplug with wet hands.

This is to avoid electric shock or injury.

Do not exceed the max water level mark

level. If spillage or overflowing occurs, it

could cause scalds.

If the water is lower than the refill mark,

discoloration of the container or other

problems may occur.

Do not attach the lid forcefully.

If spillage or overflowing occurs, it could

cause scalds.

Do not insert or boil anything other than

water.

Do not pour tea, milk, alcoholic beverages,

tea bags, tea leaves, bincho charcoal, or

instant food into the electric water heater

/ warmer. Doing so may create bubbles

causing the contets to overflow. This may

cause scalds, corrosion, malfunction or

peeling of the fluoropolymer-coated surface.

Do not use as an ice cooler.

Cold water or ice may cause dew

condensation, electric shock, or other

problems.

Do not remove the lid while the water is

boiling.

Do not hold the main unit close to your

body, tilt or rock it, or shake vigorously.

Even if the dispense lock button is "locked,"

do not tilt or tip the product. This is to avoid

scalds caused by spillage.

Disassemble

is prohibited. Do not touch

the unit with

wet hands.

5

Do not tip over the product.

Even if the dispense lock button is "locked,"

do not tilt or tip the product. This is to avoid

scalds caused by spillage.

Do not immerse the appliance in water, or

pour water into the appliance;

this is to avoid short circuits, electric shocks,

and malfunctions.

Do not discard remaining hot water with

the lid closed, this is to avoid scalds due

to hot water spillage if the lid were to

come off.

(Refer to p. 6,15 on how to discard

remaining water)

If the lid gasket changes color or is

damaged, be sure to replace it. If not

replaced, water may spill if tipped over;

possibly causing scalds.

Never immerse

the unit in water

or other liquid.

Do not place any foreign objects in the

steam vent.

Hot water may spray out causing a burn.

Stop using the appliance immediately if

you incur any malfunction or trouble. Not

doing so may result in fire, electric shock,

or injury.

Examples of trouble:

• The power cord and/or plug become

abnormally hot.

• The power goes in and out when the power

cord is moved.

• When the appliance becomes abnormally

hot or there is a smell of something burning.

• Water leaks from the main unit.

• There are other problems or abnormalities.

Immediately unplug the power cord from

the outlet and contact your local dealer for

servicing.

Unplug power cord when not in use. This

is to avoid injury, scalds, electric shock,

or fire caused by a short-circuit.

Be sure to firmly hold the plug when

removing from an outlet; this is to avoid

electric shock, shorting, or fire.

Use only the power cord which is included

with this product.

Do not use the included power cord with any

other appliance.

Do not use multiple

outlet receptacles,

this is to avoid fire.

Do not use or place in areas prone to

getting wet and do not allow the bottom

of the main unit to get wet. This is to avoid

shorting, electric shock, or malfunction.

Do not fill the water directly from the

faucet or wet the bottom of the product.

Water may get into the product and cause

shorting, electric shock, or malfunction.

Do not place any glasses or vases

containing water on top of the appliance.

This could cause the appliance to deform

or deteriorate which could cause fire. Also,

spilled water could cause electric shocks, fire,

or malfunctions.

Do not expose the plug to steam.

Doing so may result in

electric shock or fire.

When using the product

on a sliding table, be

careful not to expose

the product to steam.

Unplug the

power cord.

1 Important Safeguards

Warning

Caution

・天面に、エアー給湯のための押し板無し。

・5Ｌサイズの高さのあるフォルム

ＰＩＥ-Ａ50＿向け　注意イラスト

English

6

Do not touch

Caution

Do not come in contact with steam or

condensation when opening or removing

the lid, this is to avoid scalds.

Do not dispense hot water or do not move

the main unit while the water is being boiled.

Hot water may splash or spill out, or steam

may cause scalds.

Do not turn on the heater while dispensing

hot water.

Hot water may splash or spill out, or steam

may cause scalds.

Do not touch hot surfaces or the glass

window during use or immediately after.

This is to avoid burns.

When carrying the main unit, do not touch

the close/open lever or the lid.

The lid may come off, and cause injuries or

scalds.

Wait until the appliance has cooled down

before performing maintenance;

this is to avoid burns from hot surfaces.

Before cleaning, be sure to remove the

plug from the outlet, then remove from

the appliance. When cleaning is complete,

be sure to check that both ends of the

power cord are dry before plugging in. Do

not move the appliance when plugged in.

Doing so may result in shorting, electric

shock, or fire.

When discarding remaining water, be sure

to discard in the direction shown in the

following illustration.

If discarded from another location, water may

get inside the main unit and cause scalds or

malfunction.

Be sure that hot

water does not

splash onto the

operation panel.

Do not splash

hot water over

the hinge area.

Location for

discarding hot water.

Hold by the

hande

The spout must

face upward.

Do not wash the entire appliance. Do

not pour water into the appliance or into

the base of the appliance; this is to avoid

short circuits and electric shocks.

Do not place the main unit upside down.

This is to avoid malfunction.

Moisture or water drop leak into the unit

caused a malfunction.

This appliance is intended to be used in

household and similar applications such as:

• staff kitchen areas in shops, offices and

other working environments;

• farm houses;

• by clients in hotels, motels and other

residential type environments;

• bed and breakfast typeenvironments.

Position the lid so that steam is directed

away from the handle.

Do not touch

• Do not use near an open flame. This is to avoid

deformation or malfunction.

• Do not use in areas exposed to direct sunlight for a

prolonged period.

The product may become hot and malfunction.

• Do not turn on the electric water heater / warmer

without water inside.

Turning the heater on with out water may cause the

inner container to discolor or malfunction.

Following these safety instructions will allow the appliance to be used for many years.

• Do not put charcoal such as Bincho charcoal into

the container, this is to avoid malfunction or peeling

of the fluoropolymer-coated surface.

• When unplugging the appliance and storing it for

an extended period of time in a location subject

to freezing temperatures, make sure there is

absolutely no water in the inner container.



7

2 Part Names and Accessories

Spout

Mesh filter

Prevents entry of

foreign objects into

the pump.

Steam vent

Receptacle

Handle

Bottom

Turns 3 60°.

Water volume indicator

Open /

close lever

Lid

Inside container

Lid gasket

Hinge

Be sure the power cord is

attached when you turn the swivel

bottom.

Caution

The numbers such as 98, 90, 80indicated

in this instruction manual are only

approximate temperatures.

Display area

Keep warm lamp

Boil

lamp

〈 Operation Panel 〉

VE Mode key

Unlock key

Kitchen Timer key

Re-boil/Timer key

Unlock

lamp

〈 Power Cord 〉

Plug

( Plug into an outlet. )

Appliance plug

( Plug into the insert

slot of the unit. )

When the water is being boiled, bubbling

sounds can be heard from inside the

container. This is normal and does not

indicate a malfunction.

Sounds

Steam sensor

You can dispense

water by pressing

the right or left

lever.

Dispense

lever

Maximum water level

Water level line

Refill water

mark

Keep water above

this level.

Energy Saving key

Temp.Set key

Be sure to clean the unit before use.

There may be a smell of plastic when

first used. This is normal and will

diminish with use.

1. Add water to max water level and then bring up to boil. (See below)

2. After water is boiled, use electric dispenser button to discard half of hot

water. (See p. 11)

3. Unplug the power cord, open the lid and then discard the rest of hot

water. (See p. 18)

English

8

1 Open the lid.

2 Pour water into the unit

with a separate container.

Fill water to level between "Max water level" and "Refill

water mark".

Do not splash water

onto the operation

panel.

Rell water

mark

T

he highest level to which

water can be poured

Max water level

Pour slowly.

• Do not fill water directly from a faucet.

Do not place the unit on wet surface.

• Automatic Boil cycle may not work when

refilling hot water above 50°C, be sure

to add lukewarm water or cold water or

press

Re-Boil/Timer

key. (See p. 9)

• Do not exceed "Max water level". Do

not boil water if the water level is lower

than refill mark.

Caution

3 Boiling Water

3 Close the lid.

Click

Hold both side of lid

and close it securely

If the lid is not closed securely, hot water

may spill and cause scaling.

Caution

4 Connect the power cord.

Receptacle

Plug in

Appliance

plug

Plug in

Outlet

Plug Beeping

sound

5 Boiling starts.

Flashing

Light

illuminates

Refer to p. 9 when selecting the temperature for

Warmer. ( If no selection is made, a temperature of

90°C will be automatically set. )

Refer to p. 13 for setting the power-saving timer.

The lid contains a built-in steam guard. This prevents

steam from venting from the product while boiling.

Before ﬁrst use / When not used for a while

99

6 Select [Keep Warm]

Press Temp.Set or VE Mode key.

■Keep Warm temperature

98(approx.98°C). 90(approx.90°C). 80(approx.80°C).

Each press of Temp.Set key changes different

temperature setting as shown.

Light

illuminates

Flashing

Beeping

sound

■ When using VE mode

Press the VE Mode key.

Press again to return to the selected keep warm

temperature.

Light

illuminates

Beeping

sound Flashing

• 4 temperatures settings are available.

(80, 90, 98 and VE Mode)

• When using VE Mode, the heater automatically turns off

after boiling is complete.

• You can change temperature setting during Boiling

cycle or Keep Warm.

• If the power cord comes off during the

temperature setting, the setting is not

completed. It will go back to default

setting. (90)

• When using VE Mode, the unit does

not turn on automatically. Press the

Re-Boil/Timer

key

to boil.

Caution

■During the boiling cycle

Flashing

Current water temperature Remaining time until boiling

Timing to start displaying remaining time will vary depending on

the amount of water and the water temperature.

Water temperature will be displayed by every 5°C. (If it is

approximately 98°C, it will display "98".)

7 Automatically set to warmer

■When boiling

Beeping sound

(repeats 5 times)

Light

illuminates

Light

turns o

Light

illuminates

■

When water temperature reaches setting temperature

...

Beeping

sound

• Do not come in contact with the steam to

avoid being scalded.

• Do not open or close the lid with excessive

force and do not dispense hot water during

the boiling cycle or immediately after boiling.

Failure to do so may cause scalds due to hot

water splashing or steam being emitted.

Caution

3 Boiling Water

English

1010

3 Boiling Water

Time table for Boiling and Cooling

Boiling from cold water Approx.35minutes

From boiling to reach 90

warmer temperature Approx.4 hour and 45 minutes

From boiling to reach 80

warmer temperature Approx.9 hour and 5 minutes

Under these conditions: full water volume, the water temperature

/ room temperature is 23°C, and voltage is normal rated voltage.

Guidelines for the time required to reach the 98 warmer temperature

are almost the same as those for boiling from cold water.

Guideline for Keeping Warm After Boiling

(When Using VE Mode)

The temperature falls over time. The less water

there is, the quicker it will cool down.

After 2 hours Approx. 94°C or hotter

The data above indicates the full water amount and room

temperature at 23°C.

Temperature displays 5°C interval on the panel. Display

temperature and actual temperature may not be match.

To re-boil during the Keep Warm cy-

cle. Press

Re-Boil/Timer

key once.

Be sure the water level is above Refill water mark.

Flashing

Light

illuminates

Beeping

sound

The lid contains a built-in steam guard. This prevents steam from

venting from the product while boiling.

Guidelines for the time required for re-boiling

when the water is at the full water level

Warmer temperature at 98, 90

Approx.5-10 minutes

Warmer temperature at 80

Approx.12-14 minutes

Adding water or reattaching the power cord during Boiling cycle,

boiling time may extend.

Boiling time may changes when using VE Mode.

11

4 Dispensing Hot Water

• Do not dispense when water level is

at "Refill water mark". Hot water may

splash when you dispense.

• Pay close attention when dispensing

hot water so as to not spin the entire

unit around.

• Always remember that water is

dispensed if you press the dispense

levers while the lock is released. This

could cause burns.

• When dispense hot water by pressing

the center of the dispense levers, be

careful as the vented steam could

cause burns.

• Make sure the unlock lamp has turned

off before turning or moving the product.

Caution

3 Press the Unlock key once.

The Dispense lever will be locked, and hot water cannot be

dispensed even if the key is pressed.

Light

turns o

Beeping

sound

■Reﬁll water when level becomes low.

Be sure to refill water before it reaches [Refill water mark],

and close the lid securely. (Caution for hot steam when

refilling water. See p. 8)

• Do not leave the unit without any water

inside, this is to avoid malfunction due

to boiling without water.

• When using VE Mode (when the plug

is connected), the water is not boiled

even when dispensing hot water.

Caution

■Function to Prevent Heating Without

Water

If there is no water, if boiling with only a little water, or if

water is added with too much force, the buzzer sounds,

the boil lamp and the keep warm lamp flash alternately,

and boiling stops.

1 Press the Unlock key once.

Light

illuminates

Beeping

sound

2 Press the Dispense lever.

Place a container under the spout, and press the

Dispense lever.

Hot water continues to dispense while pressing the lever.

After checking that hot water has stopped dispensing, remove the

container from the spout

If the unit is unplugged, hot water cannot be dispensed.

When water is boiled, air pressures increases in the container so

that the water dispenser may not produce a smooth water flow

immediately after its boiled. Release the air pressure by opening

the lid and then dispense the water. Caution for hot steam.

Mineral deposits can build on the wall of the inner container, mesh

filter or pump unit, causing water to not dispense.

If the Dispense lever is not pressed for approx. 10 seconds after

dispensing hot water, the unlock lamp will be turned off and the

unit will lock automatically.

Dispense

lever

English

12

5 How to use Energy Saving Mode

■Water reaches setting temperature...

Beeping

sound

■If the unit is not in use for 2 hours, it

will automatically switch to Energy

Saving Mode.

( 5°C lower than regular setting temperature)

The heater is off during VE Mode cycle so water temperature

will decrease accordingly.

How to bring back to setting

temperature.

Press Temp.Set or Unlock key once. Bring back to

setting temperature about a minute.

How to cancel Energy Saving

Mode

Press Energy Saving key for a second. (It

automatically reheats when the temperature is low.)

You may hear a buzzing

sound when you are selecting

Energy Saving Mode, the unit

automatically reheats to setting

temperature.(See p. 18)

Energy Saving Mode applies to Boiling and Keep Warm

cycles.

• Energy Saving Mode Boiling: heater will shut off when

temperature reaches 98°C and reduce boiling steam.

(Depending on the room and water temperature, the

steam cut function may not work.)

• Energy Saving Mode cycle applies after 2 hours not in

use. It reduces approximately 5°C from regular setting

temperature e.g.: If you select 98, Energy Saving Mode is

95.

1 Select [Energy Saving Mode]

Press and hold Energy Saving key for a second.

Flashing

Beeping

sound

Light

illuminates

2 Select [Keep Warm]

(See p. 9)

3 Once water reaches boil-

ing point, it automatically

switches to Keep Warm

mode.

■When boiling cycle is done...

Light

illuminates

Light

illuminates

Beeping sound

(repeats 5 times)

Light

turns o

13

6 Using the Power-Saving Timer

Power-Saving timer can be set in 1 hour intervals from 6

to 10 hours. You can set the timer before going to sleep

or before going out. The power is turned off while using

the energy saving timer. When the time is up, the unit will

automatically reheat.

Press the

Re-Boil/Timer

key twice

and select energy saving hours

Be sure to check the status on the display.

Beeping

sound

Light

turns o

Light

turns o

Remaining time will be displayed on an hourly

basis until one hour before the Power-Saving Timer

completes the operation.

■ The unit will start to boil 1 hour before

The unit will start to boil 1 hour before the completion of

the timer; the display will show 59 minutes counting down

to 1 minute.

■ After boiling, keep warm at setting

temperature.

Light

illuminates

• Electric Dispenser does not work while

Power-Saving Timer is on.

• Do not set this while using VE Mode.

Since the heater is not set to ON, the

hot water cools down slowly.

Caution

How to Cancel the Timer

Press the Re-Boil / Timer key to turn the Boil lamp on.

Flashing

Beeping

sound

Light

illuminates

English

14

7 Using the Kitchen Timer

1 Press the Kitchen Timer key,

and then set the time.

Press to increase in one minute intervals from 1 to 30

minutes. (Hold down to increase quickly.)

Beeping

sound

■Available times

Set in one minute intervals from 1 to 30 minutes.

cancellation

min min min min



The time to the end is displayed

in minutes

Beeping

sound

Flashing

Minutes display

One minute from the end, the

display changes to seconds

and displays 59 to 1

Flashing

One minute from end,

display changes to seconds

When the set time is reached,

the buzzer sounds 10 times.

Returns to the display before setting

■Canceling the kitchen timer

Press the Kitchen Timer key while the kitchen timer is

operating.

Returns to the display before setting

Beeping

sound

Beeping

sound

■Kitchen Timer is available while

boiling or keeping warm.

15

8 After Finishing Using the Heater

1 Unplug

Unplug

Beeping

sound

Unplug

2 Remove the lid

While pressing down on the attach / remove lever for the

lid, open and remove the lid by pulling the lid toward the

spout.

Attach /

remove

lever for li

d

3 Discard remaining hot water

(Refer to p. 6)

• Do not turn the spout downward with

the lid on, or discard hot water from the

hinge area, this is to avoid scalds from

splashing hot water or malfunction.

• Move the unit to the kitchen sink and

then discard water slowly. Caution

for hot water may splash during this

operation.

• Watch out for hot water dripping from

the spout immediately after discarding

the hot water.

• Be sure to clean the inner container

and mesh filter. (Refer to p. 16)

Caution

4 Attach the lid

While pressing down on the attach/remove lever for the

lid, insert the hook-on part of the lid.

Attach /

remove

lever for lid

• Do not leave hot water remaining

inside the container, this is to avoid

discoloration of the inside container or

foul odors from forming.

• Pay extra attention when discarding the

remaining hot water, as the mesh filter

may fall if it is not properly attached.

Caution

English

16

9 Cleaning

Any other servicing should be performed by an authorized service representative.

Unplug, discard remaining hot water, and wait until the unit cools down before cleaning can be started.

Only use clean soft materials such as cloth, sponge, or paper towel.

Parts Cleaning

Inner

container

❶Simply rinse thoroughly with water and wipe the inside liner with a clean

sponge or paper towel.

• To prevent damage to the water heater do not use alkaline cleaning agents

when cleaning, use a soft cloth and a mild detergent.

• Do not use any material such as a cleanser or scrubber for tough stains

or mineral deposit; this is to avoid damage to the non-stick (flouropolymer)

coating surface.

• All water that contains minerals will leave mineral residue on the inside

liner when boiled. If not cleaned for a prolonged period, mineral build up or

stains may become tough or louder noises can be heard while boiling water.

Frequent cleaning is recommended.

• Mineral deposit will eventually block the pipes and/or the steam vent if not

removed. This blockage will cause the motor unit to burn when the "Dispense"

key is pressed persistently.

• Do not scrub and/or do not use a knife to remove the mineral deposit.

• Discoloration caused by a dry boil is not removable.

Caution

❷

For mineral build up, use citric acid cleaner every 2-3 months

(refer to p. 17)

■Uneven colors or discoloration of the inner container and

ﬂoating white material in the water

Red spots such as rust, milky white discoloration, black spots, iridescence that appear in the

inner container, and floating white material are caused by a reaction of the minerals (calcium,

magnesium, iron, etc.) contained in the water. This is not discoloration, rust, or peeling of the

fluoropolymer-coated surface of the inner container itself. Although there are no sanitary /

health concerns, frequent cleaning is recommended when the heater starts to show stains.

Wipe off stains with a damp cloth or paper towel.

Power cord Wipe off with dry cloth.

Remove the mesh filter from inner container. Wash with soft brush e.g.: tooth brush.

• Do not soak the unit in water and do not pour water on the unit, this is to avoid shorting or electric shock.

• Never wash the entire unit, this is to avoid water getting inside the unit to cause malfunction.

• Do not use harmful materials such as detergent, thinner, cleanser, bleach, metal scrubber, nylon scrubber,

and chemically-treated wiping cloths.

• Do not put in the dishwasher or dish dryer, this is to avoid deformation.

Caution

Lid

Exterior

of the unit

Mesh

lter

• Frequent washing is recommended, this is to avoid clogging that may cause

improper dispensing of hot water.

• After washing, be sure to attach the filter firmly to the inner container.

• If not attached, foreign objects may enter, causing the pump to stop dispensing.

Caution

17

9 Cleaning

How to remove mineral deposit with citric acid

When washing the inner container with

citric acid, be sure to follow the directions

below, this is to avoid hot water spills or

scalds.

• Do not fill with hot water. Be sure to wash

with cold water.

• Do not fill with water above the full water

level.

• Do not open the lid during cleaning cycle.

Caution

Other functions are not available during cleaning cycle.

Citric acid can be purchased by contacting the Tiger

product retailer where the heater was purchased,

specifying product number PKS-0120 "citric acid (approx.

30g x 4 packs) for cleaning the inner container of the

electric heater".

Citric Acid is used as natural food preservative. It is not

harmful to your health.

■< 90 minutes citric acid cleaning using

QUICK function > For soft water

(The guideline is once every 2-3 months)

❶

Be sure that the mesh filter is set in the inner container.

❷Fill with cold water into the water heater up to the full

water level capacity mark.

❸Add 1 package of PKS-0120 ( 30g / 2-3 tablespoons)

citric acid powder into the water heater and mix a little.

❹Close the lid and plug in and keep pressing the

Temp.Set key and the Re-Boil / Timer key at the

same time for about 3 seconds.

At the same time for about 3 seconds.

Beeping

sound

Washing will start. While the unit is being washed, the

boiling lamp and the warmer lamp will alternately flash,

notifying that washing is underway with the display panel

changing as shown below. It will then switch to display

the remaining washing time.

(Cleaning Time: 1 hour and 30 min)

cleaning hour may vary depending in the water temperature.

Alternately

Flashing

❺When washing is finished, the boiling lamp and the

warmer lamp will illuminate.

The display panel will indicate as follows:

Recurring

beeping sound

(repeats 10 times)

Light

illuminates

Light

illuminates

❻Discardallofthehotwater(citricacidwater)using

Dispenseleverthroughthespout.

❼Unplug and discard the hot water. If stains remain,

scrub with a sponge and rinse well with water.

If mineral deposit is still attached on the wall of inner

container, repeat the cleaning process.

❽To rinse remaining citric acid, refill with clean water

and bring up to boil. Then discard half of water using

Dispense lever, open the lid discard rest of water.

If you like to stop cleaning cycle, unplug

the power cord. Be sure to discard citric

acid water before using it again.

Caution

■

< 8 hours citric acid cleaning using 98

temperature setting > For hard water

Do not use the Quick cleaning function.

(The guideline is once every 15-30 days)

❶

Be sure that the mesh filter is set in the inner container.

❷Fill with cold water into the water heater up to the full

water level capacity mark.

❸Add 1 package of PKS-0120 (30g / 2-3 tablespoons)

citric acid powder into the water heater and mix a little.

❹

Close the lid and plug in and select 98 temperature setting.

❺Leave it at least 8 hours or overnight.

❻Press the Dispense lever and have 1 / 3 of the water

be discarded from the spout.

❼Unplug the water heater and remove the top lid to toss

the remainder of the water. (See p. 6 diagram for

the discarding location of hot water)

Note: Please use necessary caution when disposing hot water, it

might cause burns or to scald.

❽Rinse off the inner container then wipe off any residue

by using a soft sponge / cloth / paper towel. Assert

caution when wiping the inner container as it is hot;

allow it to cool down a little.

Note: If mineral build up persists, repeat the process.

❾

To remove the smell of citric acid, boil only water as

usual and dispense approximately half of the hot water

through the spout and discard the rest of the water.

If not using for a prolonged period

❶Clean each part in accordance with the directions on

p. 16, and wipe with a dry cloth.

❷Dry each part. (The inside container must particularly

be thoroughly dried.)

❸Place in a plastic bag, etc., and store sealed.

If storing, be sure to tightly seal in a plastic

bag, etc., so that no bugs or dust can get in.

Caution

English

18

10

Troubleshooting

Check the following before asking for a repair.

Symptom Check Action

Reference

page

Water does not boil.

(All the lamps are off and

blank on display panel.)

Is the plug connected? Connect the plug. 8

Does not start to boil after

refilling the water.

(Boil light does not lit)

Has the container been filled with hot water

hotter than approx. 50°C?

Refill with either cooled water or cold water. 8

Bring the water to a boil by pressing the

Re-Boil / Timer key. 9

Hot water comes out on its own.

Is the water level above the "Max water level?"

Keep water below the "Max water level." 8

There is a rasping sound

when water is being boiled.

It is the sound of bubbles bursting which are generated by the water being boiled, and it

does not indicate a problem. 7

Did you select Energy Saving Mode cycle? Selecting other cycle during Energy Saving

Mode, re-boil starts automatically. You may hear a boiling sound. 12

The sound of boiling seems

louder than usual. Is the inner container dirty? Wash the inner container with citric acid. 17

Does not boil. Did you select Energy Saving Mode?

Boiling will stop when temperature reaches

approx.98°C to reduce the boiling steam.

Press the Re-Boil / Timer key to start

boiling. 8

•

9

No steam is vented. The lid contains a built-in steam guard. This prevents steam from venting from the product

while boiling.

-

Steam vents from the gap

between the lid and the

product

Water may have entered the casing of the water heater while adding water to the water

heater or washing it, and the water heater is malfunctioning. Contact the store where you

purchased the product to request repairs.

-

The hot water smells. Depending on the amount of disinfectant

chlorine in the tap water, the chlorine smell

may remain.

Select boiling cycle with dechlorinate. 8

•

9

Do you select Energy Saving Mode?

Boiling will stop when temperature reaches

approx.98°C to reduce the steam.

Although there may be a smell of plastic or other materials for the first several times, they

become less noticeable with use.

-

Did you place the unit on plastic tray or vinyl sheet? Water may absorb the resin smell.

The exterior of the unit is

hot.

If the unit is kept warm in a room with a high temperature, the exterior of the unit may

become hot. This is not unusual.

-

The inner container is dirty.

White material is floating in

the hot water.

This is caused by a reaction of the minerals

contained in the water, and it is not discoloration,

rust, or the peeling of the fluoropolymer surface

on the inner container itself.

Clean the unit with Citric Acid. 17

The water is not hot

enough. Did you select Energy Saving Mode? Press Temp.Set or Unlock key. Bring up to

setting temperature in a minute. 12

Is it set to VE Mode?

The water cools gradually over time.

Select another keep warm temperature, or

press the Re-Boil / Timer key to boil. 9

If there is only a small amount of water in the water heater, it will cool down quickly when

using VE Mode. 9

The first cup of hot water may not be very hot, because the water stored in the water pipe of

the water volume indicator comes out first.

-

19

10

Troubleshooting

Symptom Check Action

Reference

page

Water does not dispense

using electric dispense key.

Was hot water dispensed while the unit was tilted?

Place the unit completely upright.

-

Is the plug connected? Connect the plug. 8

Is it set to lock automatically? Press the Unlock key once to dispense hot

water. 9

Is it immediately after the water has boiled?

Open the lid once while watching out for steam.

Water does not dispense

using electric dispense key. Are the mesh filter or the inside pump dirty? Clean the unit with Citric Acid. 17

Display panels are fogged

up.

Was the unit placed in an area prone to become

wet or an area where the bottom can get wet?

Discard water, unplug, and leave until the

panels are clear.

If you still have cloud in the water scale,

please contact customer service.

-

Has the unit been placed upside down?

When refilling with water, was water

splashed onto the operation panel?

Display Messages

Symptom Check Action

Reference

page

The unit is equipped with Dry-Boil Protection.

Boil lamp and Keep Warm lamp flash alternately

and signs (as shown) appear on the display.

Is there no water or very little

water in the container? Unplug, and refill to above the

refill level of the water volume

indicator. Leave as is for a while,

then plug in. 8

Has the unit been left for a

prolonged period after all of the hot

water was dispensed, or has lid been

left open while refilling with water?

When refilling, is water being

poured with excessive force?

Unplug, leave for a while, then

plug in.

The unit will notify you by beeping. Boiling Lamp

and Keep Warm Lamp flash alternately will appear

on the display as shown on right.

Flashing

-

When refilling or cleaning the

heater, water may get inside

the unit and cause problems.

Request repair work from the

Tiger product retailer where the

appliance was purchased.

-

Specifications

Capacity 5.0L

Power source AC220V (50/60Hz)

Power consumption Electric power for boiling water 928 W

Electric power for the warmer 65 W

Exterior size (approximate)

(with the handle pushed down)

Width 23.4cm

Depth 30.2cm

Height 39.3cm

Weight (approximate) (including power cord) 4.0kg

 Specified functions cannot be guaranteed in some areas (high altitude, extremely cold regions, etc.) Avoid using the unit in such locations.

Flashing

Pagina se încarcă ...

Tiger PIE-A50W Instruction manuals

Tiger PIE-A50W Instruction manuals

în alte limbi

Lucrări conexe

Alte documente