Parkside PLPRS 1.5 B3 Operating Instructions Manual

LAMINATE/PARQUET REPAIR KIT

PLPRS 1.5 B3

IAN 326890_1904

LAMINAT-/PARKETT-REPARATURSET

Bedienungsanleitung

LAMINATE/PARQUET REPAIR KIT

Operating instructions

КОМПЛЕКТ ЗА РЕМОНТ НА

ЛАМИНАТ/ПАРКЕТ

Ръководство за експлоатация

ΣΕΤ ΕΠΙΔΙΟΡΘΩΣΗΣ ΛΑΜΙΝΕΪΤ/ΠΑΡΚΕ

Οδηүίες χρήσης

SET ZA POPRAVAK LAMINATA/PARKETA

Upute za upotrebu

SET ZA POPRAVKU LAMINATA/PARKETA

Uputstvo za upotrebu

KIT PENTRU REPARAREA PARCHETULUI

Instrucţiuni de utilizare

GB / CY Operating instructions Page 1

HR Upute za upotrebu Stranica 15

RS Uputstvo za upotrebu Strana 29

RO Instrucţiuni de utilizare Pagina 43

BG Ръководство за експлоатация Cтраница 57

GR / CY Οδηүίες χρήσης Σελίδα 71

DE / AT / CH Bedienungsanleitung Seite 87

Before reading, unfold both pages containing illustrations

and familiarise yourself with all functions of the device.

Rasklopite prije čitanja obije stranice sa slikama i nakon toga

se upoznajte sa svim funkcijama uređaja.

Pre čitanja rasklopite obe strane sa slikama te se upoznajte sa

svim funkcijama uređaja.

Înainte de a citi instrucţiunile, priviţi imaginile şi familiarizaţi-vă

cu toate funcţiile aparatului.

Преди да прочетете отворете двете страници с фигурите

и след това се запознайте с всички функции на уреда.

Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τις δυο σελίδες με τις

εικόνες και εξοικειωθείτε με όλες τις λειτουργίες της συσκευής.

Klappen Sie vor dem Lesen die beiden Seiten mit den Ab-

bildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

A B

C D

E F

G H

I

3

J+H

1

J+F

6

I+F

8

H+D

10

F+D

12

E+B

14

E+G

17

C+B

4

J+G

2

J+I

5

J+E

7

H+F

9

G+E

11

F+C

13

E+A

15

E+F

16

D+C

18

C+A

GB

│

CY

│

1 ■PLPRS 1.5 B3

Table of contents

Introduction .....................2

Limited liability ........................2

Intended use ..........................2

Warnings used ........................3

Safety . . . . . . . . . . . . . . . . . . . . . . . . . .3

Handling batteries .....................4

Basic safety instructions .................5

First use.........................6

Items supplied and transport inspection . . . . . 6

Disposal of the packaging ...............6

Battery insertion/exchange ..............6

Operating elements ..............7

Colour mixing chart...............7

Handling and operation ...........8

Heat up the wax melter tip ............... 8

Application example....................8

Troubleshooting..................9

Malfunction causes and remedies .........9

Cleaning .......................10

Storage when not in use ..........10

Disposal .......................10

Disposal of the appliance...............10

Disposing of the batteries ...............10

Appendix ......................11

Technical data........................11

Kompernass Handels GmbH warranty.....11

Service .............................13

Importer ............................13

■ 2

│

GB

│

CY PLPRS 1.5 B3

Introduction

Congratulations on the purchase of your new

appliance.

You have clearly decided in favour of a high-

quality product. These operating instructions are

a part of this product. They contain important

information in regard to safety, use and disposal.

Before using the product, familiarise yourself

with all operating and safety instructions. Use

this appliance only as described and only for

the speciﬁed areas of application. Retain these

instructions for future reference. In addition, pass

these operating instructions on to whoever might

acquire the appliance at a future date.

Limited liability

All technical information, data and information for

installation, connection and operation contained

in these operating instructions correspond to the

latest at time of printing and, to the best of our

knowledge, take into account our previous experi-

ence and know-how. No claims can be derived

from the details, illustrations and descriptions in

these instructions. The manufacturer assumes no

responsibility for damage caused by failure to

observe these instructions, improper use, incompe-

tent repairs, making unauthorised modiﬁcations or

for using unapproved replacement parts.

Intended use

This laminate/parquet repair kit is intended for

the repair of laminate, parquet, cork and wood

or plastic surfaces. The supplied wax melter is

intended exclusively for the melting of hard wax

suitable for these applications. The appliance is

intended exclusively for domestic use. Do not

use the appliance for commercial or industrial

applications. Use the appliance only in a dry

environment resp. in indoor areas. This appliance

is not intended for any other use or for uses

beyond those detailed. Claims of any kind for

damage resulting from unintended use will not

be accepted. The user alone bears the risk.

GB

│

CY

│

3 ■PLPRS 1.5 B3

Warnings used

In these extant operating instructions the following

warnings are used:

DANGER

A warning at this risk level indicates

a threateningly dangerous situation.

If the dangerous situation is not avoided, it could

lead to death or serious physical injury.

► Follow the instructions in this warning to avoid

the death of or serious physical injury to people.

WARNING

A warning at this risk level indicates

a potentially dangerous situation.

If the dangerous situation is not avoided, it could

lead to physical injuries.

► Follow the instructions in this warning to avoid

personal injuries.

CAUTION

A warning at this risk level indicates

potential property damage.

If the situation is not avoided it could lead to

property damage.

► Follow the directives in this warning to avoid

property damage.

NOTICE

► A notice indicates additional information

that could assist you in the handling of the

appliance.

Safety

In this chapter you will receive important safety

information regarding the handling of the appli-

ance. This appliance complies with the statutory

safety regulations. Incorrect usage can lead to

personal injury and property damage.

DANGER

► Do not use the appliance in

locations where there is a risk of

ﬁre or explosion, e.g. in the vicinity

of inﬂammable liquids or gases.

■ 4

│

GB

│

CY PLPRS 1.5 B3

Handling batteries

WARNING

Risks from uses other than

those intended! There is a risk

of explosions and leakage!

For the safe handling of batteries,

take note of the following safety

instructions:

► Do not throw batteries into a ﬁre.

► Never short-circuit batteries.

► Do not attempt to recharge

batteries.

► Regularly check the condition of

the batteries. Leaking battery acid

can cause permanent damage to

the appliance. Special caution

should be exercised when handling

damaged or leaking batteries.

There is a risk of receiving acid

burns! Wear protective gloves.

► Store batteries in a place

i naccessible to children. If a

battery should be swallowed,

seek medical attention

IMMEDIATELY.

► If you do not intend to use the

appliance for an extended period,

remove the batteries.

GB

│

CY

│

5 ■PLPRS 1.5 B3

Basic safety instructions

For safe handling of the appliance,

follow the safety information below:

■ Before use, check the appliance for

visible external damage. Do not take

into use a damaged appliance or one

that has been dropped.

■ Do not make any unauthorised

modiﬁcations or alterations to the

appliance.

■ This appliance may be used by children

aged 8 over and by persons with

reduced physical, sensory or mental

capabilities or lack of experience and

knowledge, provided that they are

under supervision or have been told

how to use of the appliance safely

and are aware of the potential risks.

Children must not play with the appli-

ance. Cleaning and user maintenance

tasks must not be carried out by

children unless they are supervised.

■ Protect the appliance against moisture

and liquid penetration.

■ Do not operate the appliance close to

open ﬂames (e.g. candles).

■ Avoid direct sunlight.

■ Avoid unintentional operation of the

wax melter.

■ Avoid skin contact with the wax

melter tip and protect yourself against

dripping wax. There is a risk of burns!

■ 6

│

GB

│

CY PLPRS 1.5 B3

First use

DANGER

During the commissioning of the appliance

personal injury and property damage

could occur!

► Packaging material should not be used as

a play thing. There is a risk of suﬀocation.

Items supplied and transport

inspection

This Laminate/Parquet Repair Set is supplied with

the following components as standard:

▯ Wax melter

▯ Cleaning scraper

▯ Scraper with planer function

▯ Scraper with curvature

▯ 11 x Hard wax sticks

▯ Sanding sponge

▯ Cleaning cloth

▯ 2 x Batteries 1.5 V Type AA/LR6/Mignon

▯ Storage case

▯ This operating manual

NOTICE

► Check the contents to ensure that everything

is available and for signs of visible damage.

► If the contents are not complete, or are dama-

ged due to defective packaging or through

transportation, contact the Service Hotline

(see chapter Service).

Disposal of the packaging

Dispose of the packaging in an

environmentally friendly manner.

Note the labelling on the packaging

and separate the packaging material

components for disposal if necessary. The packaging

material is labelled with abbreviations (a) and

numbers (b) with the following meanings:

1–7: Plastics, 20–22: Paper and cardboard,

80–98: Composites.

Battery insertion/exchange

This wax melter requires 2 x 1.5 V batteries,

type AA/LR6/Mignon, for operation.

♦ Open the battery compartment

on the

back of the wax melter

.

♦ Insert the batteries into the wax melter

as indicated in the battery compartment

(see ﬁg. 1).

♦ Close the battery compartment

.

GB

│

CY

│

7 ■PLPRS 1.5 B3

AA

Fig. 1

Operating elements

Wax melter

Wax melter tip

Activation button ON /OFF

Battery compartment

Red LED

Cleaning scraper

Scraper with planer function

Scraper with curvature

Sanding sponge

Cleaning cloth

Battery type AA/LR6/Mignon

Colour mixing chart

(see back fold-out page for colour samples)

The rear fold-out page shows a selection of types

of wood. The colour samples displayed there are

only intended as a guide and are non-binding.

Minor colour deviations are possible. Use the

following chart to determine your type of wood:

1

Maple

2

Pine

3 Birch 4 Pine Medium

5 Limba 6

Alder Medium -

Finish

7

Alder Dark -

Honey

8 Beech - Dark

9 Teak 10 Pear - Dark

11 Macoré - Dark 12 Walnut - Light

13 Oak - Dark 14 Oak - Rustic

15 Oak - Brownish 16 Mahogany - Light

17 Walnut - Medium 18 Mahogany - Dark

NOTE

► To achieve your desired colour, select a base

colour (ﬁrst letter, e. g. J+F) and mix it with

the second colour (second letter, e.g. J+F).

The colour selection is indicative. Several

other colours can be mixed.

■ 8

│

GB

│

CY PLPRS 1.5 B3

Handling and operation

In this chapter you will receive important infor-

mation for the handling and operation of the

appliance.

Heat up the wax melter tip

♦ Press and hold the activation button ON /

OFF

to heat up the wax melter tip .

The red LED

will remain lit as long as you

hold down the activation button ON /

OFF

.

Application example

Preparation (Fig. A)

♦ Clean the damaged area with the spatula

and remove all loose parts. Press the edges

of the damaged area round.

Colour selection (Fig. B)

♦ Select the matching colour tone.

Ensure that several colour tones, from light to

dark, are always used. With real wood, it is

recommended to additionally work with trans-

parent (K), so as to achieve a sense of depth.

Melting and ﬁlling (Figs. C + D)

♦ Press and hold the activation button ON /

OFF

to heat up the wax melter tip .

The appliance reaches operating temperature

after about 15 seconds.

♦ Now melt small portions of the hard wax and

place them into the damaged area, until it is

slightly overﬁlled. Start with the light colour

tones and progress step by step to the dark

colour tones.

NOTICE

► At pressure points it is often suﬃcient if you

use only the transparent hard wax (K).

Filling (Fig. E)

♦ For vertical surfaces it is recommended to mix

the colour tone beforehand, collect it on the

spatula

and then ﬁll the damaged area.

When working on curved areas the scraper

with curvature

should be used to ﬁll hard

wax into the damaged area.

CAUTION

► The wax melter tip

gets very hot! When

mixing the colour, use a work surface made

of a suitable heat-resistant material, such as

ceramic.

GB

│

CY

│

9 ■PLPRS 1.5 B3

Smoothing (Fig. F)

♦ Allow the hard wax to cool for a few seconds

(about 10 seconds).

♦ After cooling, smooth any protrusion with the

planing grooves of the scraper

. Use only

light pressure to smooth the protrusion.

Fine matching (Fig. G)

♦ For ﬁne matching, now imitate the grain struc-

ture with a darker colour tone.

♦ Subsequently, again smooth any protrusion

with the planing grooves of the scraper

.

Degreasing (Fig. H)

♦ To ﬁnish, remove the last hard wax residues

with the sanding sponge

. Thereby the

gloss level of the surface will also be simulta-

neously matched. Job done!

Cleaning the planer grooves (Fig. I)

♦ Place the cleaning scraper

on the plane

grooves of the scraper

and scrape the wax

residues from the plane grooves.

Troubleshooting

In this chapter you will receive important informa-

tion for malfunction localisation and malfunction

remedies.

Malfunction causes and remedies

The following table will help with localising and

remedying minor malfunctions:

Defect

Possible

cause

Solution

The wax melter

tip

does not

get hot.

The batteries

have been

inserted

incorrectly.

Insert the

batteries into

the wax melter

as indicated

in the battery

compartment

.

The batteries

are dischar-

ged.

Insert two new

batteries.

NOTICE

► If you cannot solve the problem with the

aforementioned solutions, please contact the

Service Hotline (see chapter Service) .

■ 10

│

GB

│

CY PLPRS 1.5 B3

Cleaning

CAUTION

Damage to the appliance!

► Ensure that, when cleaning it, no moisture can

penetrate into the appliance, so as to avoid

irreparable damage to it.

► Do not use chemical or abrasive cleaning

agents. These could damage the housing.

♦ Clean the wax melter

and the wax melter

tip

with the cleaning cloth only when

they have cooled down.

♦ Scrape the wax residue oﬀ the wax melter tip

using the scraper with curvature

.

Storage when not in use

If you do not intend to use the appliance for an

extended period of time, remove the batteries.

Store all parts of the Laminate/Parquet Repair Kit

in the storage case and at a clean, dry location

out of direct sunlight.

Disposal

Disposal of the appliance

Do not dispose of the appliance in

your normal domestic waste. This

product is subject to the provisions of

European Directive 2012/19/EU

WEEE (Waste Electrical and Electronic

Equipment).

Dispose of the appliance through an ap-

proved disposal centre or at your community

waste facility. Please pay heed to the currently

applicable regulations. In case of doubt,

please contact your waste disposal centre.

Your local community or municipal authorities

can provide information on how to dispose of

the worn-out product.

Disposing of the batteries

Do not dispose of the batteries with domestic

waste. Every consumer is statutorily obliged to

dispose of batteries/rechargeable batteries

at a collection point in their community/district

or to a dealer.

This obligation is intended to ensure that

batteries are disposed of in an environmentally

responsible manner. Dispose of batteries only

when they are fully discharged.

GB

│

CY

│

11 ■PLPRS 1.5 B3

Appendix

Technical data

Voltage supply

batteries

2 x 1.5 V

(direct current)

type AA/LR6/Mignon

Dimensions approx. 14.7 x 3.5 x 2.2 cm

Weight

(including batteries) approx. 90 g

Kompernass Handels GmbH

warranty

Dear Customer,

This appliance has a 3-year warranty valid from

the date of purchase. If this product has any

faults, you, the buyer, have certain statutory

rights. Your statutory rights are not restricted in

any way by the warranty described below.

Warranty conditions

The warranty period starts on the date of pur-

chase. Please keep your receipt in a safe place.

This will be required as proof of purchase.

If any material or manufacturing fault occurs

within three years of the date of purchase of

the product, we will either repair or replace the

product for you or refund the purchase price (at

our discretion). This warranty service requires

that you present the defective appliance and the

proof of purchase (receipt) within the three-year

warranty period, along with a brief written de-

scription of the fault and of when it occurred.

If the defect is covered by the warranty, your

product will either be repaired or replaced by us.

The repair or replacement of a product does not

signify the beginning of a new warranty period.

Warranty period and statutory

claims for defects

The warranty period is not prolonged by repairs

eﬀected under the warranty. This also applies to

replaced and repaired components. Any dam-

age and defects present at the time of purchase

must be reported immediately after unpacking.

Repairs carried out after expiry of the warranty

period shall be subject to a fee.

■ 12

│

GB

│

CY PLPRS 1.5 B3

Scope of the warranty

This appliance has been manufactured in accord-

ance with strict quality guidelines and inspected

meticulously prior to delivery.

The warranty covers material faults or produc-

tion faults. The warranty does not extend to

product parts subject to normal wear and tear

or to fragile parts which could be considered as

consumable parts such as switches, batteries or

parts made of glass.

The warranty does not apply if the product has

been damaged, improperly used or improperly

maintained. The directions in the operating

instructions for the product regarding proper use

of the product are to be strictly followed. Uses

and actions that are discouraged in the operating

instructions or which are warned against must be

avoided.

This product is intended solely for private use and

not for commercial purposes. The warranty shall

be deemed void in cases of misuse or improper

handling, use of force and modiﬁcations / repairs

which have not been carried out by one of our

authorised Service centres.

Warranty claim procedure

To ensure quick processing of your case, please

observe the following instructions:

■ Please have the till receipt and the item num-

ber (e.g. IAN12345) available as proof of

purchase.

■ You will ﬁnd the item number on the type

plate on the product, an engraving on the

product, on the front page of the operating

instructions (below left) or on the sticker on

the rear or bottom of the product.

■ If functional or other defects occur, please

contact the service department listed either by

telephone or by e-mail.

■ You can return a defective product to us free

of charge to the service address that will be

provided to you. Ensure that you enclose the

proof of purchase (till receipt) and informa-

tion about what the defect is and when it

occurred.

GB

│

CY

│

13 ■PLPRS 1.5 B3

You can download these instruc-

tions along with many other

manuals, product videos and

installation software at

www.lidl-service.com.

This QR code will take you directly

to the Lidl service page (www.lidl-service.com)

where you can open your operating

instructions by entering the item number

(IAN) 123456.

Service

Service Great Britain

Tel.: 0800 404 7657

E-Mail: kom[email protected]

CY

Service Cyprus

Tel.: 8009 4409

E-Mail: kom[email protected]

IAN 326890_1904

Importer

Please note that the following address is not the

service address. Please use the service address

provided in the operating instructions.

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

GERMANY

www.kompernass.com

■ 14

│

GB

│

CY PLPRS 1.5 B3

HR

│

15 ■PLPRS 1.5 B3

Sadržaj

Uvod ..........................16

Ograničenje odgovornosti ..............16

Namjenska uporaba...................16

Korištena upozorenja ..................17

Sigurnost ......................17

Rukovanje baterijama ..................18

Opće sigurnosne napomene ............19

Puštanje u pogon................20

Opseg isporuke i provjera transporta......20

Zbrinjavanje ambalaže.................20

Umetanje/zamjena baterija .............20

Upravljački elementi .............21

Tablica za miješanje boja .........21

Rukovanje i rad .................22

Zagrijavanje vrha uređaja za topljenje voska 22

Primjer za primjenu ....................22

Otklanjanje smetnji ..............23

Uzroci pogrešaka i njihovo otklanjanje.....23

Čišćenje ........................24

Čuvanje za vrijeme nekorištenja ...24

Zbrinjavanje....................24

Zbrinjavanje uređaja ..................24

Zbrinjavanje baterija...................24

Prilog..........................25

Tehnički podaci.......................25

Jamstvo tvrtke Kompernass Handels GmbH . 25

Servis ..............................27

Uvoznik.............................27

■ 16

│

HR PLPRS 1.5 B3

Uvod

Srdačno čestitamo na kupnji Vašeg novog uređaja.

Time ste se odlučili za visokovrijedan proizvod.

Upute za rukovanje predstavljaju sastavni dio

ovog proizvoda. One sadrže važne napomene

za sigurnost, rukovanje i zbrinjavanje. Prije upo-

rabe uređaja upoznajte se sa svim pripadajućim

uputama za uporabu i svim sigurnosnim napo-

menama. Proizvod koristite isključivo na opisani

način i u navedenim područjima uporabe. Saču-

vajte ove upute za rukovanje. U slučaju predaje

proizvoda trećim osobama priložite i predajte i

svu dokumentaciju.

Ograničenje odgovornosti

Sve tehničke informacije, svi podaci i sve napo-

mene za priključivanje i posluživanje uređaja

sadržani u ovim uputama za rukovanje odgova-

raju najnovijem stanju tehnike u trenutku pripreme

za tisak i navedeni su uz uvažavanje naših dosa-

dašnjih iskustava i saznanja. Na osnovu navoda,

slika i opisa sadržanih u ovim uputama za ruko-

vanje ne mogu se izvoditi nikakva potraživanja.

Proizvođač ne preuzima odgovornost za štete

nastale uslijed nepridržavanja uputa za rukova-

nje, nenamjenske uporabe, nestručno izvedenih

popravaka, neovlašteno izvršenih izmjena ili

uporabe nedozvoljenih zamjenskih dijelova.

Namjenska uporaba

Set za popravak laminata/parketa predviđen je

za popravak laminata, parketa, plutenih, drvenih

i plastičnih površina. Uređaj za topljenje voska

sadržan u opsegu isporuke namijenjen je isključivo

za topljenje prikladnog tvrdog voska. Uređaj je

namijenjen isključivo za privatnu uporabu.

Uređaj ne koristite u gospodarske ili industrijske

svrhe. Uređaj koristite isključivo u suhom okruženju,

odn. u zatvorenim prostorima. Svaki drugi način

uporabe i svaka uporaba koja prelazi navedene

okvire smatra se nenamjenskom. Isključena su

sva potraživanja bilo koje vrste na temelju štete

nastale uslijed nenamjenske uporabe. Rizik snosi

isključivo sam korisnik.

Pagina se încarcă ...

Parkside PLPRS 1.5 B3 Operating Instructions Manual

Parkside PLPRS 1.5 B3 Operating Instructions Manual

Lucrări conexe

Alte documente