Hilti SJT 6 Instrucțiuni de utilizare

SJT 6

English 1

Español 11

Português 21

Eesti 32

Latviešu 41

Lietuvių 52

Slovenščina 62

Hrvatski 72

Русский 82

Українська 93

Қазақ 105

Български 116

Română 127

Ελληνικά 138

Türkçe 149

ﻋﺮﺑﻲ 160

한국어 171

繁體中文 180

1

2

3

4

5

6

7

8

9

10

11

12

SJT 6

en Original operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

es Manual de instrucciones original . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

pt Manual de instruções original . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

et Originaalkasutusjuhend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

lv Oriģinālā lietošanas instrukcija . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

lt Originali naudojimo instrukcija . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

sl Originalna navodila za uporabo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

hr Originalne upute za uporabu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

ru Перевод оригинального руководства по эксплуатации . . . . . . . . . . . . . . . . . . . . 82

uk Оригінальна інструкція з експлуатації . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

kk Түпнұсқа пайдалану бойынша нұсқаулық . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

bg Оригинално Ръководство за експлоатация . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116

ro Manual de utilizare original . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

el Μετάφραση οδηγιών χρήσης από το πρωτότυπο . . . . . . . . . . . . . . . . . . . . . . . . . 138

tr Orijinal kullanım kılavuzu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149

ar ﺩﻟﻴﻞﺍﻻﺳﺘﻌﻤﺎﻝﺍﻷﺻﻠﻲ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160

ko 오리지널 사용 설명서 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171

zh 原始操作說明 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180

*2150300*

2150300 English 1

Original operating instructions

1 Information about the documentation

1.1 About this documentation

• Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free

handling and use of the product.

• Observe the safety instructions and warnings in this documentation and on the product.

• Always keep the operating instructions with the product and make sure that the operating instructions

are with the product when it is given to other persons.

1.2 Explanation of symbols used

1.2.1 Warnings

Warnings alert persons to hazards that occur when handling or using the product. The following signal words

are used:

DANGER

DANGER !

▶ Draws attention to imminent danger that will lead to serious personal injury or fatality.

WARNING

WARNING !

▶ Draws attention to a potential threat of danger that can lead to serious injury or fatality.

CAUTION

CAUTION !

▶ Draws attention to a potentially dangerous situation that could lead to slight personal injury or damage

to the equipment or other property.

1.2.2 Symbols in the documentation

The following symbols are used in this document:

Read the operating instructions before use.

Instructions for use and other useful information

Dealing with recyclable materials

Do not dispose of electric equipment and batteries as household waste

1.2.3 Symbols in the illustrations

The following symbols are used in illustrations:

These numbers refer to the corresponding illustrations found at the beginning of these operating

instructions

The numbering reflects the sequence of operations shown in the illustrations and may deviate

from the steps described in the text

Item reference numbers are used in the overview illustrations and refer to the numbers used in

the product overview section

This symbol is intended to draw special attention to certain points when handling the product.

2 English 2150300

*2150300*

1.3 Product-dependent symbols

1.3.1 Symbols on the product

The following symbols are used on the product:

Stroke rate under no load

Wireless data transfer

1.4 Product information

products are designed for professional users and only trained, authorized personnel are

permitted to operate, service and maintain the products. This personnel must be specifically informed

about the possible hazards. The product described and its ancillary equipment can present hazards if used

incorrectly by untrained personnel or if used not in accordance with the intended use.

The type designation and serial number are printed on the type identification plate.

▶ Write down the serial number in the table below. Always quote this information when you contact a Hilti

representative or Hilti Service to inquire about the product.

▶ Write down the serial number in the table below. Always quote this information when you contact a Hilti

representative or Hilti Service to inquire about the product.

Product information

Orbital-action jig saw SJT 6

Generation 01

Serial no.

1.5 Declaration of conformity

We declare, onour sole responsibility, that the product described here complies with the applicable directives

and standards. A copy of the declaration of conformity can be found at the end of this documentation.

The technical documentation is filed here:

Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916 Kaufering, Germany

2 Safety

2.1 General power tool safety warnings

WARNING Read all safety warnings, instructions, illustrations and specifications provided with this

power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

▶ Keep work area clean and well lit. Cluttered or dark areas invite accidents.

▶ Do not operate power tools in explosive atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

▶ Keep children and bystanders away while operating a power tool. Distractions can cause you to lose

control.

Electrical safety

▶ Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of

electric shock.

▶ Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

▶ Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the

risk of electric shock.

▶ Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the

risk of electric shock.

*2150300*

2150300 English 3

▶ When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric shock.

▶ If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of electric shock.

Personal safety

▶ Stay alert, watch what you are doing and use common sense when operating a power tool. Do

not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools may result in serious personal injury.

▶ Use personal protective equipment. Always wear eye protection. Protective equipment such as a

dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will

reduce personal injuries.

▶ Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power

source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on

the switch or energising power tools that have the switch on invites accidents.

▶ Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in personal injury.

▶ Do not overreach. Keep proper footing and balance at all times. This enables better control of the

power tool in unexpected situations.

▶ Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from

moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

▶ If devices are provided for the connection of dust extraction and collection facilities, ensure these

are connected and properly used. Use of dust collection can reduce dust-related hazards.

▶ Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore

tool safety principles. A careless action can cause severe injury within a fraction of a second.

Power tool use and care

▶ Do not force the power tool. Use the correct power tool for your application. The correct power tool

will do the job better and safer at the rate for which it was designed.

▶ Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

▶ Disconnect the plug from the power source and/or remove the battery pack, if detachable, from

the power tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

▶ Store idle power tools out of the reach of children and do not allow persons unfamiliar with the

power tool or these instructions to operate the power tool. Power tools are dangerous in the hands

of untrained users.

▶ Maintain power tools and accessories. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s operation. If damaged,

have the power tool repaired before use. Many accidents are caused by poorly maintained power

tools.

▶ Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

▶ Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking

into account the working conditions and the work to be performed. Use of the power tool for

operations different from those intended could result in a hazardous situation.

▶ Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

Service

▶ Have your power tool serviced by a qualified repair person using only identical replacement parts.

This will ensure that the safety of the power tool is maintained.

2.2 Safety instructions for reciprocating saws

▶ Hold the power tool by insulated gripping surfaces, when performing an operation where the

cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a "live"

wire may make exposed metal parts of the power tool "live" and could give the operator an electric

shock.

▶ Use clamps or another practical way to secure and support the workpiece to a stable platform.

Holding the workpiece by hand or against your body leaves it unstable and may lead to loss of control.

4 English 2150300

*2150300*

2.3 Additional safety instructions

Personal safety

▶ Use the tool only when it is in technically faultless condition.

▶ Never tamper with or modify the tool in any way.

▶ Always hold the power tool with both hands on the grips provided. Keep the grips clean and dry.

▶ Suitable protective glasses, ear protection and protective gloves must be worn while the tool is in use.

▶ Wear protective gloves when changing the accessory tool. Touching the accessory tool presents a risk

of injury (cuts or burns).

▶ Wear eye protection. Flying fragments present a risk of injury to the body and eyes.

▶ Before beginning the work, check the hazard classification of the dust that will be produced. Use an

industrial vacuum cleaner with an officially approved protection classification in compliance with locally

applicable dust protection regulations.

▶ Make sure that the workplace is well ventilated and, where necessary, wear a respirator appropriate for

the type of dust generated. Contact with or inhalation of the dust may cause allergic reactions and/or

respiratory or other diseases to the operator or bystanders. Certain kinds of dust are classified as

carcinogenic such as oak and beech dust, especially in conjunction with additives for wood conditioning

(chromate, wood preservative). Material containing asbestos may be handled only by specialists.

▶ Take breaks between working and do physical exercises to improve the blood circulation in your fingers.

Exposure to vibration during long periods of work can lead to disorders of the blood vessels and nervous

system in the fingers, hands and wrists.

Electrical safety

▶ Before beginning work, check the working area for concealed electric cables or gas and water pipes.

External metal parts of the power tool may give you an electric shock if you damage an electric cable

accidentally.

Careful handling and use of electric tools

▶ Secure the workpiece. A workpiece clamped in a vice or secured by some other clamping device is more

secure than when held only by hand.

Special safety instructions for jig saws

▶ Always guide the product away from your body when working with it.

▶ Never position your hands ahead of or on the saw blade.

▶ Never cut into unknown materials and keep the line of cut above and below the workpiece free of

obstacles.

▶ Never reach or grip below the workpiece while cutting.

3 Description

3.1 Product overview 1

@

On/off switch

;

Grip

=

Stroke rate regulator thumbwheel

%

Air vents

&

Suction adapter

(

Catches

)

Base plate

+

Lever for orbital action

§

Anti-splinter insert

/

Saw blade

:

Contact guard

∙

Guard

$

Blade holder

£

Saw blade release lever

3.2 Intended use

The product described is a hand-held, electrically powered orbital-action jig saw. It is designed for cutting

plastic, wood and metal materials, drywall board and gypsum fiberboard.

*2150300*

2150300 English 5

The product is equipped with a removable connector for an optional vacuum cleaner / dust removal hose.

This connector is designed to fit standard suction hoses. In order to connect the suction hose to the product,

use of a suitable adapter may be necessary.

The tool may be operated only when connected to a power source providing a voltage and frequency in

compliance with the information given on the type identification plate.

▶ Use this product only with saw blades equipped with a T-shank.

3.3 Possible misuse

• Use of the product to cut off tree branches or to cut the trunk of a tree is not permissible.

• Use of the product to cut hazardous materials is not permissible.

• Use of the product in a damp or wet environment is not permissible.

3.4 Dust blower

The dust blower directs a jet of air toward the saw blade in order to keep the cutting line free of dust.

3.5 Stroke rate

The stroke rate can be adjusted by turning the thumbwheel. Position 1 corresponds to 800 strokes per

minute and position 6 corresponds to 3000 strokes per minute.

3.6 4 orbital-action settings

The 4 orbital-action settings allow cutting performance and quality of cut to be adjusted to suit the material

to be cut. The orbital-action adjustment lever is used to set the power tool to one of the 4 settings.

The lower the orbital-action setting, the finer and cleaner the cut edges will be. The optimum setting can be

determined by carrying out practical tests.

Status Meaning

Position 0 No orbital action

Position 1 Low orbital action

Position 2 Medium orbital action

Position 3 High orbital action

3.7 Anti-splinter insert

The product can be equipped with an anti-splinter insert.

The anti-splinter insert helps prevent splintering on the surface of wood materials when cutting.

3.8 Items supplied

Orbital-action jig saw with saw blade, guard, dust removal adapter, anti-splinter insert, operating instructions,

hex key.

You can find other system products approved for your product at your local Hilti Center or online at:

www.hilti.com

4 Technical data

4.1 Orbital-action jig saw

When powered by a generator or transformer, the generator or transformer’s power output must be at

least twice the rated input power shown on the rating plate of the power tool. The operating voltage of

the transformer or generator must always be within +5% and -15% of the rated voltage of the power

tool.

The information given applies to a rated voltage of 230 V. The data may vary in the event of deviations

from the rated voltage and for country-specific versions. Please refer to the power tool’s type

identification plate for details of its voltage, frequency, current and input power ratings.

6 English 2150300

*2150300*

SJT 6

Rated power input

850 W

Weight in accordance with EPTA procedure 01

2.4 kg

Stroke rate under no load

800 /min … 3,000 /min

Stroke length

28 mm

Maximum cutting performance in wood

150 mm

Maximum cutting performance in aluminum

25 mm

Maximum cutting performance in unalloyed steel

10 mm

Cutting angle (left/right)

0°, 15°, 30°, 45°

Suction adapter outside diameter

27.5 mm

4.2 Noise information and vibration values in accordance with EN 62841

The sound pressure and vibration values given in these instructions were measured in accordance with a

standardized test and can be used to compare one power tool with another. They can also be used for a

preliminary assessment of exposure.

The data given represent the main applications of the power tool. However, if the power tool is used for

different applications, with different accessory tools, or is poorly maintained, the data can vary. This can

significantly increase exposure over the total working period.

An accurate estimation of exposure should also take into account the times when the tool is switched off, or

when it is running but not actually being used for a job. This can significantly reduce exposure over the total

working period.

Identify additional safety measures to protect the operator from the effects of noise and/or vibration, for

example: maintaining the power tool and accessory tools, keeping the hands warm, organization of work

patterns.

Noise emission values

SJT 6

Sound power level (L

WA

)

98 dB(A)

Uncertainty for the sound power level (K

WA

)

5 dB(A)

Sound pressure level (L

pA

)

87 dB(A)

Uncertainty for the sound pressure level (K

pA

)

5 dB(A)

Total vibration

SJT 6

Vibration emission value for sawing wood sheets (a

h,B

)

12.1 m/s²

Vibration emission value for sawing sheet metal (a

h,M

)

10.7 m/s²

Uncertainty (K)

1.5 m/s²

5 Using extension cords

WARNING

A damaged supply cord presents a hazard! Do not touch the supply cord or extension cord if damaged

while working. Disconnect the supply cord plug from the power outlet.

▶ Check the appliance’s supply cord at regular intervals and have it replaced by a qualified specialist if

found to be damaged.

• Use only extension cords of a type approved for the application and with conductors of adequate gauge

(cross section). The power tool may otherwise suffer a drop in performance and the extension cord may

overheat.

• Check the extension cord for damage at regular intervals.

• Replace damaged extension cords.

• When working outdoors, use only extension cords that are approved and correspondingly marked for

this application.

*2150300*

2150300 English 7

Information on recommended minimum conductor cross-sections and cable lengths is accessible via

a link, in the form of a QR code, at the end of this document.

6 Preparations at the workplace

CAUTION

Risk of injury! Inadvertent starting of the product.

▶ Unplug the supply cord before making adjustments to the power tool or before changing accessories.

Observe the safety instructions and warnings in this documentation and on the product.

6.1 Fitting the saw blade 2

1. Disconnect the supply cord plug from the power outlet.

2. Push the saw blade (teeth facing the cutting direction) into the blade holder until it engages.

3. Grip and pull the saw blade to check that it is held securely.

6.2 Fitting the guard 3

▶ Push the guard onto the product from the front until it clicks into place.

6.3 Fitting the suction adapter 4

1. Push the suction adapter onto the base plate horizontally from the rear until both catches engage at the

side.

2. Connect the vacuum cleaner hose to the suction adapter.

6.4 Setting the orbital action 5

1. Determine the correct orbital-action setting for the task to be performed with the applicable saw blade.

2. Set the orbital-action adjusting lever to one of the four settings → page 5.

6.5 Adjusting the stroke rate 6

Determine the correct setting for the task to be performed with the applicable saw blade.

▶ Set the stroke rate regulator thumbwheel to a setting between 1 (low) and 6 (high).

6.6 Setting the cutting angle 7

1. Remove the suction adapter. → page 8

2. Pivot the clamping lever 90° back (toward the rear of the tool).

3. Set the desired cutting angle (0°, 15°, 30° or 45°).

4. Pivot the clamping lever 90° forward (toward the front of the tool).

▶ The base plate is clamped securely.

5. Fit the suction adapter. → page 7

6.7 Fitting the anti-splinter insert 8

The anti-splinter insert can be used only with the saw blades for which it is designed.

1. Disconnect the supply cord plug from the power outlet.

2. Press the anti-splinter insert into the base plate from below.

8 English 2150300

*2150300*

7 Types of work

WARNING

Damaged power cords are a safety hazard! If the supply cord or extension cord is damaged while work

is in progress, immediately disconnect the device and the cord from the electricity supply. Do not touch the

damaged part of the cord.

▶ Regularly check all supply cords. Replace defective extension cords. Have damaged power cords

replaced by a qualified specialist.

Use of a ground fault circuit interrupter (residual current device, RCD) with a maximum tripping current of

30 mA is recommended.

7.1 Dust removal system

The dust extractor reduces dust emissions, increases working safety by providing better visibility of

the cutting line and reduces exposure to dust and wood chips at the workplace.

1. Fit the guard. → page 7

2. Connect the dust removal adapter and the extractor when you intend working for a long period on wood

or other materials, because high concentrations of dust can be produced in these operations.

7.2 Switching on 9

▶ Use the sliding switch to switch the product on.

7.3 Plunge cutting

1. Set the orbital-action adjusting lever to position 0.

2. Bring the front edge of the base plate into contact with the workpiece.

3. Hold the product securely and press the on/off switch.

4. Press the product firmly against the workpiece and begin the plunge cut by slowly reducing the angle of

attack.

5. Once the blade has penetrated right through the workpiece, bring the product into its normal working

position.

▶

The base plate then lies flat on the working surface.

6. Continue to saw along the cutting line.

7.4 Switching off

▶ Use the sliding switch to switch the product off.

8 Removal

CAUTION

Risk of injury! Inadvertent starting of the product.

▶ Unplug the supply cord before making adjustments to the power tool or before changing accessories.

Observe the safety instructions and warnings in this documentation and on the product.

8.1 Removing the suction adapter 10

1. Press the two retaining catches inwards.

2. Pull the suction adapter to the rear to remove it from the base plate.

3. Disconnect the vacuum cleaner hose from the suction adapter.

8.2 Removing the guard 11

▶ Tilt the guard slightly and pull it off toward the front.

*2150300*

2150300 English 9

8.3 Ejecting the saw blade 12

WARNING

Risk of injury. Uncontrolled ejection of the saw blade can lead to injury.

▶ When ejecting the saw blade, hold the product in such a way that it presents no risk of injury to persons

or animals.

1. Disconnect the supply cord plug from the power outlet.

2. Push the saw blade ejection lever to the side as far as it will go.

▶ The saw blade will be released and ejected.

9 Care and maintenance

WARNING

Electric shock hazard! Attempting care and maintenance with the supply cord connected to a power outlet

can lead to severe injury and burns.

▶ Always unplug the supply cord before carrying out care and maintenance tasks.

Care

• Carefully remove any dirt that may be adhering to parts.

• Clean the air vents carefully with a dry brush.

• Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as

these may attack the plastic parts.

Maintenance

WARNING

Danger of electric shock! Improper repairs to electrical components may lead to serious injuries including

burns.

▶ Repairs to the electrical section of the tool or appliance may be carried out only by trained electrical

specialists.

• Check all visible parts and controls for signs of damage at regular intervals and make sure that they all

function correctly.

• Do not operate the product if signs of damage are found or if parts malfunction. Have it repaired

immediately by Hilti Service.

• After cleaning and maintenance, fit all guards or protective devices and check that they function correctly.

To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare

parts, consumables and accessories approved by Hilti for use with the product can be found at your

local Hilti Store or online at: www.hilti.group.

9.1 Cleaning the suction adapter

1. Disconnect the supply cord plug from the power outlet.

2. Disconnect the vacuum cleaner hose from the suction adapter.

3. Remove the suction adapter. → page 8

4. Clean the suction adapter.

5. Check that the catches are undamaged.

6. Fit the suction adapter. → page 7

9.2 Cleaning the saw blade

1. Clean resin deposits from used saw blades at regular intervals.

2. Place the saw blades in a bath of kerosene (paraffin oil) or commercially-available resin remover for 24

hours.

10 Transport and storage

Transport

▶ Do not transport this product with an accessory tool installed.

10 English 2150300

*2150300*

▶ Make sure that the equipment is held securely throughout all transport operations.

▶ After transporting, always check all visible parts and controls for signs of damage and make sure that

they all function correctly.

Storage

▶ Always store this product with the electric supply cable unplugged from the electricity supply.

▶ Store this product in a dry place, where it cannot be accessed by children or unauthorized persons.

▶ After a long period of storage, always check all visible parts and controls for signs of damage and make

sure that they all function correctly.

11 Troubleshooting

If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by

yourself, please contact Hilti Service.

Trouble or fault Possible cause Action to be taken

The saw blade drops out. The saw blade is not correctly en-

gaged.

▶ Repeat the insertion procedure.

▶ Make sure that the blade holder

is fully open and that the saw

blade is pushed all the way in

against the spring resistance.

The clamping system is clogged

with foreign matter.

▶ Clean out the blade holder.

The saw blade cannot be

inserted.

The clamping system is clogged

with foreign matter.

▶ Clean out the blade holder.

The orbital action cannot be

adjusted.

Foreign matter in the orbital-action

adjusting lever groove.

▶ Clean out the orbital-action

adjusting lever groove.

The orbital action doesn’t

work.

The orbital-action mechanism is

clogged with foreign matter.

▶ Check whether foreign matter

is present in the area of the

orbital-action fork and clean it

out.

The orbital-action adjusting lever is

in position “0”.

▶ Adjust it to the desired setting.

The power tool gets very hot. Electrical fault. ▶ Switch off immediately and

unplug the power cord from the

electricity supply.

▶ Allow the power tool to cool

down and consult Hilti Service.

12 Disposal

Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The

materials must be correctly separated before they can be recycled. In many countries, your old tools,

machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative

for further information.

▶ Do not dispose of power tools, electronic equipment or batteries as household waste!

13 RoHS (Restriction of Hazardous Substances)

Click on the links to go to the table of hazardous substances: qr.hilti.com/r5212957.

There is a link to the RoHS table, in the form of a QR code, at the end of this document.

14 Manufacturer’s warranty

▶ Please contact your local Hilti representative if you have questions about the warranty conditions.

*2150300*

2150300 Español 11

Manual de instrucciones original

1 Información sobre la documentación

1.1 Acerca de esta documentación

• Lea detenidamente esta documentación antes de la puesta en servicio. Ello es imprescindible para un

trabajo seguro y un manejo sin problemas.

• Respete las indicaciones de seguridad y las advertencias presentes en esta documentación y en el

producto.

• Conserve este manual de instrucciones siempre junto con el producto y entregue el producto a otras

personas siempre acompañado del manual.

1.2 Explicación de símbolos

1.2.1 Avisos

Las advertencias de seguridad advierten de peligros derivados del manejo del producto. Se utilizan las

siguientes palabras de peligro:

PELIGRO

PELIGRO !

▶ Término utilizado para un peligro inminente que puede ocasionar lesiones graves o incluso la muerte.

ADVERTENCIA

ADVERTENCIA !

▶ Término utilizado para un posible peligro que puede ocasionar lesiones graves o incluso la muerte.

PRECAUCIÓN

PRECAUCIÓN !

▶

Término utilizado para una posible situación peligrosa que puede ocasionar lesiones leves o daños

materiales.

1.2.2 Símbolos en la documentación

En esta documentación se utilizan los siguientes símbolos:

Leer el manual de instrucciones antes del uso

Indicaciones de uso y demás información de interés

Manejo con materiales reutilizables

No tirar las herramientas eléctricas y las baterías junto con los desperdicios domésticos

1.2.3 Símbolos en las figuras

En las figuras se utilizan los siguientes símbolos:

Estos números hacen referencia a la figura correspondiente incluida al principio de este manual

La numeración describe el orden de los pasos de trabajo en la imagen y puede ser diferente de

los pasos descritos en el texto

Los números de posición se utilizan en la figura Vista general y los números de la leyenda están

explicados en el apartado Vista general del producto

Preste especial atención a este símbolo cuando utilice el producto.

12 Español 2150300

*2150300*

1.3 Símbolos dependientes del producto

1.3.1 Símbolos en el producto

En el producto se utilizan los siguientes símbolos:

Número de carreras en marcha en vacío

Transferencia de datos inalámbrica

1.4 Información del producto

Los productos han sido diseñados para usuarios profesionales y solo personal autorizado y

debidamente formado puede utilizarlos y llevar a cabo su mantenimiento y conservación. Este personal debe

estar especialmente instruido en lo referente a los riesgos de uso. La utilización del producto descrito y sus

dispositivos auxiliares puede conllevar riesgos para el usuario en caso de manejarse de forma inadecuada

por personal no cualificado o utilizarse para usos no previstos.

La denominación del modelo y el número de serie están indicados en la placa de identificación.

▶ Anote el número de serie en la siguiente tabla. Mencione estos datos siempre que realice alguna consulta

acerca del producto a nuestros representantes o al Departamento de Servicio Técnico.

▶ Anote el número de serie en la siguiente tabla. Mencione estos datos siempre que realice alguna consulta

acerca del producto a nuestros representantes o al Departamento de Servicio Técnico.

Datos del producto

Sierra de calar de carrera pendular SJT 6

Generación 01

N.º de serie

1.5 Declaración de conformidad

Bajo nuestra exclusiva responsabilidad, declaramos que el producto aquí descrito cumple con las directivas

y normas vigentes. Encontrará una reproducción de la declaración de conformidad al final de esta

documentación.

La documentación técnica se encuentra depositada aquí:

Hilti Entwicklungsgesellschaft mbH | Zulassung Geräte | Hiltistraße 6 | 86916 Kaufering, DE

2 Seguridad

2.1 Indicaciones generales de seguridad para herramientas eléctricas

ADVERTENCIA Lea con atención todas las indicaciones de seguridad, instrucciones, ilustraciones

y datos técnicos correspondientes a esta herramienta eléctrica. La negligencia en el cumplimiento

de las instrucciones que se describen a continuación podría provocar descargas eléctricas, incendios o

lesiones graves.

Conserve todas las instrucciones e indicaciones de seguridad para futuras consultas.

El término «herramienta eléctrica» empleado en las indicaciones de seguridad se refiere a herramientas

eléctricas portátiles, ya sea con cable de red o sin cable, en caso de ser accionadas por batería.

Seguridad en el puesto de trabajo

▶ Mantenga su área de trabajo limpia y bien iluminada. El desorden o una iluminación deficiente de las

zonas de trabajo pueden provocar accidentes.

▶

No utilice la herramienta eléctrica en un entorno con peligro de explosión en el que se encuentren

líquidos, gases o polvos inflamables. Las herramientas eléctricas producen chispas que pueden llegar

a inflamar los materiales en polvo o vapores.

▶ Mantenga alejados a los niños y otras personas de su puesto de trabajo al emplear la herramienta

eléctrica. Una distracción le puede hacer perder el control sobre la herramienta.

Seguridad eléctrica

▶ El enchufe de la herramienta eléctrica debe corresponder a la toma de corriente utilizada. No

se deberá modificar el enchufe en forma alguna. No utilice enchufes adaptadores para las

herramientas eléctricas con puesta a tierra. Los enchufes sin modificar adecuados a las respectivas

tomas de corriente reducen el riesgo de descarga eléctrica.

*2150300*

2150300 Español 13

▶ Evite el contacto corporal con superficies que tengan puesta a tierra, como pueden ser tubos,

calefacciones, cocinas y frigoríficos. El riesgo a quedar expuesto a una sacudida eléctrica es mayor

si su cuerpo tiene contacto con tierra.

▶ No exponga las herramientas eléctricas a la lluvia y evite que penetren líquidos en su interior. El

riesgo de recibir descargas eléctricas aumenta si penetra agua en la herramienta eléctrica.

▶ No utilice el cable de conexión para transportar o colgar la herramienta eléctrica ni tire de él para

extraer el enchufe de la toma de corriente. Mantenga el cable de conexión alejado de fuentes de

calor, aceite, aristas afiladas o piezas móviles. Los cables de conexión dañados o enredados pueden

provocar descargas eléctricas.

▶ Cuando trabaje al aire libre con una herramienta eléctrica, utilice exclusivamente un alargador

adecuado para exteriores. La utilización de un alargador adecuado para su uso en exteriores evita el

riesgo de una descarga eléctrica.

▶ Cuando no pueda evitarse el uso de la herramienta eléctrica en un entorno húmedo, utilice un

interruptor de corriente de defecto. La utilización de un interruptor de corriente de defecto evita el

riesgo de una descarga eléctrica.

Seguridad de las personas

▶ Permanezca atento, preste atención durante el trabajo y utilice la herramienta eléctrica con

prudencia. No utilice una herramienta eléctrica si está cansado, ni tampoco después de haber

consumido alcohol, drogas o medicamentos. Un momento de descuido al utilizar la herramienta

eléctrica podría producir graves lesiones.

▶ Utilice el equipo de seguridad personal adecuado y lleve siempre gafas protectoras. El riesgo

de lesiones se reduce considerablemente si, según el tipo y la aplicación de la herramienta eléctrica

empleada, se utiliza un equipo de seguridad personal adecuado como una mascarilla antipolvo, zapatos

de seguridad con suela antideslizante, casco de protección o protección para los oídos.

▶ Evite una puesta en servicio fortuita de la herramienta. Asegúrese de que la herramienta eléctrica

está apagada antes de alzarla, transportarla, conectarla a la toma de corriente o insertar la

batería. Si transporta la herramienta eléctrica sujetándola por el interruptor de conexión/desconexión

o si introduce el enchufe en la toma de corriente con la herramienta conectada, podría producirse un

accidente.

▶ Retire las herramientas de ajuste o llaves fijas antes de conectar la herramienta eléctrica. Una

herramienta o llave colocada en una pieza giratoria puede producir lesiones al ponerse en funcionamiento.

▶ Evite adoptar posturas forzadas. Procure que la postura sea estable y manténgase siempre en

equilibrio. De esta forma podrá controlar mejor la herramienta eléctrica en caso de presentarse una

situación inesperada.

▶ Utilice ropa adecuada. No utilice vestimenta amplia ni joyas. Mantenga su pelo, vestimenta y

guantes alejados de las piezas móviles. La vestimenta suelta, las joyas y el pelo largo se pueden

enganchar con las piezas en movimiento.

▶ Siempre que sea posible montar equipos de aspiración o captación de polvo, asegúrese de que

están conectados y de que se utilizan correctamente. El uso de un sistema de aspiración de polvo

reduce los riesgos derivados del polvo.

▶ No se crea a salvo de cualquier riesgo ni pase por alto ninguna de las normas de seguridad

relativas a las herramientas eléctricas, aun cuando esté familiarizado con la herramienta eléctrica

y tenga larga experiencia en su uso. Una actuación negligente puede provocar lesiones graves en

cuestión de segundos.

Uso y manejo de la herramienta eléctrica

▶ No sobrecargue la herramienta. Utilice la herramienta eléctrica adecuada para el trabajo que se

dispone a realizar. Con la herramienta eléctrica apropiada podrá trabajar mejor y de modo más seguro

dentro del margen de potencia indicado.

▶ No utilice herramientas eléctricas con el interruptor defectuoso. Las herramientas eléctricas que no

se puedan conectar o desconectar son peligrosas y deben repararse.

▶ Extraiga el enchufe de la toma de corriente o retire la batería extraíble antes de efectuar cualquier

ajuste en la herramienta, cambiar accesorios o en caso de no utilizar la herramienta durante un

tiempo prolongado. Esta medida preventiva evita el riesgo de arranque accidental de la herramienta

eléctrica.

▶ Guarde las herramientas eléctricas que no utilice fuera del alcance de los niños. No permita

utilizar la herramienta a ninguna persona que no esté familiarizada con ella o que no haya leído

este manual de instrucciones. Las herramientas eléctricas utilizadas por personas inexpertas son

peligrosas.

▶ Cuide su herramienta eléctrica y los accesorios adecuadamente. Compruebe si las piezas móviles

de la herramienta funcionan correctamente y sin atascarse, y si existen piezas rotas o deterioradas

que pudieran afectar al funcionamiento de la herramienta eléctrica. Encargue la reparación de las

14 Español 2150300

*2150300*

piezas defectuosas antes de usar la herramienta eléctrica. Muchos accidentes son consecuencia de

un mantenimiento inadecuado de la herramienta eléctrica.

▶ Mantenga los útiles limpios y afilados. Las herramientas de corte bien cuidadas y con aristas afiladas

se atascan menos y se guían con más facilidad.

▶ Utilice la herramienta eléctrica, los accesorios, útiles de inserción, etc., de acuerdo con estas

instrucciones. Para ello, tenga en cuenta las condiciones de trabajo y la tarea que se va a realizar.

El uso de herramientas eléctricas para trabajos diferentes de aquellos para los que han sido concebidas

puede resultar peligroso.

▶ Mantenga las empuñaduras y las superficies de contacto secas, limpias y sin residuos de aceite

o grasa. Las empuñaduras y superficies de contacto resbaladizas impiden manejar y controlar la

herramienta eléctrica con seguridad en situaciones imprevistas.

Servicio Técnico

▶ Solicite que un profesional lleve a cabo la reparación de su herramienta eléctrica y que utilice

exclusivamente piezas de repuesto originales. Solamente así se garantiza la seguridad de la

herramienta eléctrica.

2.2 Indicaciones de seguridad para sierras con hojas de sierra de vaivén

▶ Sujete la herramienta eléctrica por las empuñaduras aisladas cuando realice trabajos en los que

el útil de inserción pueda entrar en contacto con cables eléctricos ocultos o con el propio cable de

conexión de la herramienta. El contacto con los cables conductores puede traspasar la conductividad

a las partes metálicas y producir descargas eléctricas.

▶ Fije y asegure la herramienta a una superficie estable con abrazaderas o mediante otro sistema.

Si solo utiliza la mano para sujetar la pieza de trabajo o se la apoya contra el cuerpo, la pieza estará

inestable, lo que puede provocar una pérdida de control.

2.3 Indicaciones de seguridad adicionales

Seguridad de las personas

▶ Utilice la herramienta únicamente si tiene la certeza de que se encuentra en perfecto estado técnico.

▶ No efectúe nunca manipulaciones o modificaciones en la herramienta.

▶ Sujete siempre la herramienta con ambas manos por las empuñaduras previstas. Mantenga las

empuñaduras secas y limpias.

▶ Cuando utilice la herramienta, lleve siempre gafas protectoras apropiadas, protección para los oídos y

guantes de protección.

▶ Utilice guantes de protección para cambiar el útil de inserción. El contacto con el útil de inserción puede

producir cortes y quemaduras.

▶ Utilice protección para los ojos. El material que sale disparado puede ocasionar lesiones en los ojos y en

el cuerpo.

▶ Antes de iniciar el trabajo, consulte la clase de peligros derivados del polvo resultante del trabajo. Utilice

un aspirador de obra con una clasificación de protección homologada conforme a las normas locales

sobre la protección contra el polvo.

▶ Procure una buena ventilación en el lugar de trabajo y utilice en caso necesario una mascarilla adecuada

para cada clase de polvo. El contacto con el polvo o su inhalación puede provocar reacciones alérgicas

o asfixia al usuario o a personas que se encuentren en su entorno. Existen determinados tipos de

polvo, como puede ser el de roble o el de haya, catalogados como cancerígenos, especialmente si se

encuentran mezclados con aditivos usados en el tratamiento de la madera (cromato, agente protector

para la madera). Únicamente expertos cualificados están autorizados a manipular materiales que

contengan asbesto.

▶ Efectúe pausas durante el trabajo, así como ejercicios de los dedos para mejorar la circulación. En el

caso de trabajos de larga duración, las vibraciones pueden causar alteraciones en el sistema nervioso o

en los vasos sanguíneos de los dedos, las manos u otras articulaciones de las manos.

Seguridad eléctrica

▶ Antes de empezar a trabajar, compruebe si la zona de trabajo oculta cables eléctricos, tuberías de gas

o cañerías de agua. Las partes metálicas exteriores de la herramienta pueden provocar una descarga

eléctrica si se daña por error un cable eléctrico.

Manipulación y utilización segura de las herramientas eléctricas

▶ Fije la pieza de trabajo. Las piezas de trabajo se sujetan de forma más segura mediante un dispositivo

de sujeción o un tornillo de banco que sujetándolas solo con la mano.

Pagina se încarcă ...

Hilti SJT 6 Instrucțiuni de utilizare

Acest manual este potrivit și pentru

Hilti SJT 6 Instrucțiuni de utilizare

în alte limbi

Lucrări conexe

Alte documente