Panasonic SCHC300EG Instrucțiuni de utilizare

Marca: Panasonic

Model: SCHC300EG

Tip: Instrucțiuni de utilizare

Acest manual este potrivit și pentru

TQBJ2071

Operating Instructions

Compact Stereo System

Model No. SC-HC302

SC-HC300

“EB” indicates the United Kingdom model.

Thank you for purchasing this product.

For optimum performance and safety, please read these instructions carefully.

Please keep this manual for future reference.

Included installation instructions. (~3, 16 and 17)

Please read these instructions carefully before installing.

This illustration shows SC-HC302.

SC-HC302.300 EB.EG TQBJ2071 En.fm Page 1 Monday, January 8, 2018 11:27 AM

TQBJ2071

These operating instructions are applicable for models

SC-HC302 and SC-HC300.

Unless otherwise indicated, illustrations in these operating

instructions are of SC-HC302. Your system and the

illustrations can look differently.

Bottom of product

Table of contents

Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Caution for AC mains lead . . . . . . . . . . . . . . . . . . . . . . . 3

Supplied accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Making the connections . . . . . . . . . . . . . . . . . . . . . . . . . 4

Preparing the remote control . . . . . . . . . . . . . . . . . . . . . 4

Overview of controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Preparing the media . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Media playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Radio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

DAB/DAB+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Clock and timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Sound effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

External music device . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Others . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Attaching the unit to a wall (optional) . . . . . . . . . . . . . . 16

References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Sales and Support Information . . . . . . . . . . . . . . . . . . . 17

Safety precautions

WARNING!

Unit

• To reduce the risk of fire, electric shock or product

damage,

– Do not expose this unit to rain, moisture, dripping or

splashing.

– Do not place objects filled with liquids, such as vases,

on this unit.

– Use the recommended accessories.

– Do not remove covers.

– Do not repair this unit by yourself. Refer servicing to

qualified service personnel.

– Do not let metal objects fall inside this unit.

• To prevent injury, this apparatus must be securely

attached to the wall in accordance with the installation

instructions.

CAUTION!

Unit

• To reduce the risk of fire, electric shock or product

damage,

– Do not install or place this unit in a bookcase, built-in

cabinet or in another confined space. Ensure this unit

is well ventilated.

– Do not obstruct this unit’s ventilation openings with

newspapers, tablecloths, curtains, and similar items.

– Do not place sources of naked flames, such as

lighted candles, on this unit.

• This unit is intended for use in moderate climates.

• This unit may receive radio interference caused by

mobile telephones during use. If such interference

occurs, please increase separation between this unit

and the mobile telephone.

• This unit utilizes a laser. Use of controls or adjustments

or performance of procedures other than those

specified herein may result in hazardous radiation

exposure.

AC mains lead

• The mains plug is the disconnecting device. Install this

unit so that the mains plug can be unplugged from the

socket outlet immediately.

Battery

• Danger of explosion if battery is incorrectly replaced.

Replace only with the type recommended by the

manufacturer.

• When disposing of the batteries, please contact your

local authorities or dealer and ask for the correct

method of disposal.

• Do not heat or expose to flame.

• Do not leave the battery(ies) in a car exposed to direct

sunlight for a long period of time with doors and

windows closed.

• Do not break open or short-circuit the battery.

• Do not charge the alkaline or manganese battery.

• Do not use the battery if the cover has peeled off.

• Remove the battery if you do not use the remote control

for a long period of time. Keep in a cool, dark area.

[HC302]:

[HC300]:

Indicate features applicable to SC-HC302.

Indicate features applicable to SC-HC300.

Product Identification Marking is located on the bottom

of the unit.

SC-HC302.300 EB.EG TQBJ2071 En.fm Page 2 Monday, January 8, 2018 11:27 AM

TQBJ2071

Caution for AC mains lead

(For the AC mains plug of three pins)

For your safety, please read the following text carefully.

This appliance is supplied with a moulded three pin mains

plug for your safety and convenience.

A 5-ampere fuse is fitted in this plug.

Should the fuse need to be replaced please ensure that

the replacement fuse has a rating of 5-ampere and that it

is approved by ASTA or BSI to BS1362.

Check for the ASTA mark or the BSI mark on the

body of the fuse.

If the plug contains a removable fuse cover you must

ensure that it is refitted when the fuse is replaced.

If you lose the fuse cover the plug must not be used until a

replacement cover is obtained.

A replacement fuse cover can be purchased from your

local dealer.

Before use

Remove the connector cover.

How to replace the fuse

The location of the fuse differ according to the type of AC

mains plug (figures A and B). Confirm the AC mains plug

fitted and follow the instructions below.

Illustrations may differ from actual AC mains plug.

1. Open the fuse cover with a screwdriver.

2. Replace the fuse and close or attach the fuse cover.

Supplied accessories

Check and identify the supplied accessories.

Use numbers indicated in parentheses when asking for

replacement parts. (Product numbers correct as of

December 2017. These may be subject to change.)

 1 AC mains lead

For the United Kingdom and Ireland

(K2CT2YY00089)

For others

(K2CQ2YY00107)

 [HC302]

1 DAB indoor antenna

(N1CYYYY00022)

 [HC300]

1 FM indoor antenna

(RSAX0002)

 1 Remote control

(N2QAYB000944)

 1 Remote control battery

Figure A Figure B

Fuse cover

Fuse (5 ampere)

Wall mount kit

 2 Wall mount brackets

(RSC1262-1)

 1 Screw

(XTB3+8JFJK-J)

 1 Safety holder

(RSC1266)

The symbols on this product (including the

accessories) represent the following:

Class II equipment (The construction of the

product is double-insulated.)

! ON

` Standby

SC-HC302.300 EB.EG TQBJ2071 En.fm Page 3 Monday, January 8, 2018 11:27 AM

TQBJ2071

Making the connections

Connect the AC mains lead only after all the other

connections have been made.

1 [HC302]

Connect the DAB indoor antenna.

Rotate the antenna at to improve reception.

Note:

• Do not use any other DAB antenna except the supplied one.

• Do not mount the DAB antenna on metal objects such as

water pipes or any metal parts of the building.

[HC300]

Connect the FM indoor antenna.

2 Connect the AC mains lead.

Do not use any other AC mains lead except the

supplied one.

Conserving power

The system consumes a small amount of power

(~15) even when it is in standby mode. Disconnect

the power supply if you do not use the system.

Some settings will be lost after you disconnect the

system. You have to set them again.

Note:

• These speakers do not have magnetic shielding. Do not put

them near TVs, PCs or other equipment easily influenced by

magnetism.

• Tape the antenna to a wall with the least amount of

interference.

• Use an outdoor antenna (not supplied) if reception is poor.

Preparing the remote control

Use alkaline or manganese battery.

Install the battery so that the poles (+ and –) align with

those in the remote control.

Adhesive tape

(not supplied)

Be sure to

tighten the nut

fully.

Adhesive tape

(not supplied)

(For the AC mains plug of three pins)

READ THE “Caution for AC mains lead” BEFORE

CONNECTION.

To household

mains socket

[HC300][HC302]

SC-HC302.300 EB.EG TQBJ2071 En.fm Page 4 Monday, January 8, 2018 11:27 AM

TQBJ2071

Overview of controls

Do the procedures with the remote control. You can also use the buttons on the main unit if they are the same.

A Standby/on switch [`], [1]

Press to switch the unit from on to standby mode or

vice versa. In standby mode, the unit is still consuming

a small amount of power.

B Select the audio source

On the remote control:

Press the corresponding button to select the source.

[ ]: BLUETOOTH

[USB/CD]: USB CD

[RADIO/AUX]:

On the main unit:

Select “BLUETOOTH” as the audio source

To start Bluetooth

pairing or disconnect a Bluetooth

device, press and hold the corresponding button.

C Basic playback control

D View the setup menu

E View the content information

F Select or confirm the option

G Open or close the sliding door

H Decrease the brightness of the display panel

To cancel, press the button again.

I Adjust the volume level

J Mute the sound

To cancel, press the button again.

“MUTE” is also cancelled when you adjust the volume

or when you switch off the system.

K View the play menu

L Select the sound effects

M AUX IN terminal (~12)

N USB port ( ) (~12)

O Sliding door

P Display panel

Q Remote control sensor

Distance: Within approximately 7 m

Angle: Approximately 20° up and down, 30° left

and right

Top view

[HC302]

SC-HC302.300 EB.EG TQBJ2071 En.fm Page 5 Monday, January 8, 2018 11:27 AM

TQBJ2071

Preparing the media

Disc

1 Press [USB/CD] to select “CD”.

2 Press [CD x] (main unit: [x]) to open the sliding

door.

Put in a disc with the label facing towards you.

3 Press [CD x] (main unit: [x]) again to close the

sliding door.

Keep fingers away from the sliding door when it is

closing.

USB

Press [USB/CD] to select “USB”.

Note:

Do not use a USB extension cable. The system cannot

recognise USB device connected through a cable.

Bluetooth

You can connect and play an audio device wirelessly

through Bluetooth

Preparation

• Switch on the Bluetooth

feature of the device and put

the device near the system.

• Read the operating instructions of the device for details.

█

Pairing a device

Preparation

If this system is connected to a Bluetooth

device,

disconnect it. (~7)

1 Press [ ] to select “BLUETOOTH”.

If “PAIRING” is shown, continue with step 3.

2 Press [PLAY MENU] to select “PAIRING”.

Or press and hold [SELECTOR/ – PAIRING] on the

main unit until “PAIRING” is shown.

3 Select “SC-HC302” or “SC-HC300” from the

Bluetooth

menu of the device.

If prompted for a passkey, input “0000”.

The device connects with this system automatically

after pairing is complete.

The MAC address (example: 6C:5A:B5:B3:1D:0F)

may be shown before “SC-HC302” or “SC-HC300” is

shown.

The name of the connected device is shown for a few

seconds.

Note:

You can pair up to 8 devices with this system. If a 9th device is

paired, the device that has not been used for the longest time

will be replaced.

█

Connecting a device

Preparation

If this system is connected to a Bluetooth

device,

disconnect it. (~7)

1 Press [ ] to select “BLUETOOTH”.

“BLUETOOTH READY” is shown.

2 Select “SC-HC302” or “SC-HC300” from the

Bluetooth

menu of the device.

The name of the connected device is shown for a few

seconds.

3 Start playback on the device.

Note:

• A device must be paired to connect.

• This system can only connect to one device at a time.

•

When “BLUETOOTH” is selected as the source, this system

will automatically try to connect to the last connected device.

(“LINKING” is shown during this process.)

USB device

(not supplied)

SC-HC302.300 EB.EG TQBJ2071 En.fm Page 6 Monday, January 8, 2018 11:27 AM

TQBJ2071

█

Disconnecting a device

1 Press [ ] to select “BLUETOOTH”.

2 Press [PLAY MENU] repeatedly to select

“DISCONNECT?”.

3 Press [R, T] to select “OK? YES” and then press

[OK].

Note:

A device is disconnected when you:

• Select a different source.

• Move the device out of the maximum range.

• Disable the Bluetooth

transmission of the device.

• Switch off the system or the device.

Link mode

You can change the link mode to suit the connection type.

Preparation

If this system is connected to a Bluetooth

device,

disconnect it. (~above)

1 Press [PLAY MENU] repeatedly to select

“LINK MODE”.

2 Press [R, T] to select the mode and then press

[OK].

Note:

• Depending on the device, the playback image and sound

may not be synchronised. In this case, select “MODE 1”.

• Select “MODE 1” if the sound is interrupted.

Input level

You can change the input level setting if the sound input

level of the Bluetooth

transmission is too low.

1 Press [PLAY MENU] repeatedly to select

“INPUT LEVEL”.

2 Press [R, T] to select the level and then press

[OK].

Note:

• The default setting is “LEVEL 0”.

• Select “LEVEL 0” if the sound is distorted.

Media playback

The following marks indicate the availability of the feature.

Basic playback

CD USB BLUETOOTH

Note:

Depending on the Bluetooth

device, some operations may

not work.

Viewing available information

CD USB BLUETOOTH

You can view the available information on the display

panel.

Press [DISPLAY].

Note:

• Maximum characters that can be shown: Approximately 32

• This system supports ver. 1.0, 1.1 and 2.3 ID3 tags.

• Text data that the system does not support can show

differently.

• Example: MP3 album and track number display.

MODE 1 Emphasis on connectivity.

MODE 2 (default) Emphasis on sound quality.

CD :

USB :

BLUETOOTH :

CD-R/RW in CD-DA format or with MP3 files.

USB device with MP3 files.

Bluetooth

device.

Play Press [4/9].

Stop Press [8].

USB

The position is memorised.

“RESUME” is shown.

Press again to stop fully.

Pause Press [4/9].

Press again to continue playback.

Skip Press [2/3] or [5/6] to skip track.

CD USB

Press [R, T] to skip MP3 album.

Search Press and hold [2/3] or [5/6].

Album

number

Track

number

SC-HC302.300 EB.EG TQBJ2071 En.fm Page 7 Monday, January 8, 2018 11:27 AM

TQBJ2071

Play menu

CD USB

1 Press [PLAY MENU] repeatedly to select

“PLAYMODE” or “REPEAT”.

2 Press [R, T] to select the setting and then press

[OK].

Note:

• During random playback, you cannot skip to tracks which

have been played.

• The setting is cancelled when you open the sliding door or

disconnect the USB device.

█

Note on disc

• This system can play CD-R/RW with CD-DA or MP3

format content.

• This system can access up to:

– CD-DA: 99 tracks

• Before playback, finalise the disc on the device it was

recorded on.

• Some CD-R/RW cannot be played because of the

condition of the recording.

█

Note on USB device

• This system does not guarantee connection with all

USB devices.

• This system supports USB 2.0 full speed.

• This system can support USB devices of up to 32 GB.

• Only FAT 12/16/32 file system is supported.

█

Note on MP3 file

• Files are defined as tracks and folders are defined as

albums.

• Tracks must have the extension “.mp3” or “.MP3”.

• Tracks will not necessarily be played in the order you

recorded them.

• Some files can fail to work because of the sector size.

MP3 file on disc

• This system can access up to:

– 255 albums (including root folder)

– 999 tracks

– 20 sessions

• Disc must conform to ISO9660 level 1 or 2 (except for

extended formats).

MP3 file on USB device

• This system can access up to:

– 800 albums (including root folder)

– 8000 tracks

– 999 tracks in one album

PLAYMODE

OFF

PLAYMODE

Cancel the setting.

1-TRACK

Play one selected track.

Press [2/3] or [5/6] to

select the track.

1-ALBUM

Play one selected MP3 album.

Press [R, T] to select the MP3 album.

RANDOM

RND

Play all tracks randomly.

1-ALBUM

RANDOM

1 RND

Play all tracks in one selected MP3

album randomly.

Press [R, T] to select the MP3 album.

REPEAT

OFF REPEAT Cancel the setting.

ON REPEAT Repeat playback.

SC-HC302.300 EB.EG TQBJ2071 En.fm Page 8 Monday, January 8, 2018 11:27 AM

TQBJ2071

Radio

Preparation

Press [RADIO/AUX] to select “FM”.

Manual tuning

1 Press [PLAY MENU] repeatedly to select

“TUNE MODE”.

2 Press [R, T] to select “MANUAL” and then press

[OK].

3 Press [2/3] or [5/6] to tune in to the

station.

To tune automatically, press and hold the button until

the frequency starts changing quickly.

“STEREO” is shown when a stereo broadcast is being

received.

Memory presetting

You can preset up to 30 FM stations.

█

Automatic presetting

1 Press [PLAY MENU] to select “A.PRESET”.

2 Press [R, T] to select “LOWEST” or “CURRENT”

and then press [OK].

The tuner presets all the stations it can receive into the

channels in ascending order.

To cancel, press [8].

█

Manual presetting

1 Press [PLAY MENU] repeatedly to select

“TUNE MODE”.

2 Press [R, T] to select “MANUAL” and then press

[OK].

3 Press [2/3] or [5/6] to tune in to the

station.

4 Press [OK].

5 Press [R, T] to select a preset number and then

press [OK].

Repeat steps 3 to 5 to preset more stations.

The new station replaces any station that occupies the

same preset number.

█

Selecting a preset station

1 Press [PLAY MENU] repeatedly to select

“TUNE MODE”.

2 Press [R, T] to select “PRESET” and then press

[OK].

3 Press [2/3] or [5/6] to select the preset

station.

Improving the sound quality

1 Press [PLAY MENU] repeatedly to select

“FM MODE”.

2 Press [R, T] to select “MONO” and then press

[OK].

To cancel, select “STEREO”.

“MONO” is also cancelled when you change the

frequency.

To memorise the setting

Continue with step 4 of “Manual presetting”. (~left)

Checking the signal status

For Continental Europe

Press [DISPLAY] repeatedly to select “FM STATUS”.

For others

Press [DISPLAY].

RDS broadcasting

For Continental Europe

This system can show the text data transmitted by the

radio data system (RDS) available in some areas.

Press [DISPLAY] repeatedly.

Note:

RDS may not be available if reception is poor.

LOWEST Tuning begins from the lowest frequency.

CURRENT Tuning begins from the current frequency.

FM - - - - The FM signal is in monaural.

The system is not tuned in to a station.

FM ST The FM signal is in stereo.

FM MONO “MONO” is selected as the “FM MODE”.

PS Programme service

PTY Programme type

FREQ Frequency

SC-HC302.300 EB.EG TQBJ2071 En.fm Page 9 Monday, January 8, 2018 11:27 AM

TQBJ2071

DAB/DAB+

[HC302]

Preparation

Press [RADIO/AUX] to select “DAB+”.

Note:

If you select “DAB+” for the first time, the system will tune

automatically.

Manual tuning

1 Press [PLAY MENU] repeatedly to select

“MANUAL SCAN”.

2 Press [R, T] to select the frequency block and

then press [OK].

If no station is detected, “SCAN FAILED” is shown.

Adjust the antenna and try again.

To tune automatically

1 Press [PLAY MENU] to select “AUTOSCAN” and

then press [OK].

“START?” is shown.

2 Press [OK] to start tuning.

“DAB AUTO SCAN” is shown.

If no station is detected, “SCAN FAILED” is shown.

Do manual tuning.

Note:

Preset frequencies are erased after you do automatic tuning.

Memory presetting

You can preset up to 20 stations.

1 Press [PLAY MENU] repeatedly to select

“TUNE MODE”.

2 Press [R, T] to select “STATION” and then press

[OK].

3 Press [2/3] or [5/6] to tune in to the

station.

4 Press [OK].

5 Press [R, T] to select a preset number and then

press [OK].

Repeat steps 3 to 5 to preset more stations.

The new station replaces any station that occupies the

same preset number.

Note:

You cannot preset a station when the station is not

broadcasting or when you have selected a secondary service.

█

Selecting a preset station

1 Press [PLAY MENU] repeatedly to select

“TUNE MODE”.

2 Press [R, T] to select “PRESET” and then press

[OK].

3 Press [2/3] or [5/6] to select the preset

station.

Secondary service

You can listen to secondary services when “ ” is shown.

1 Press [PLAY MENU] repeatedly to select

“DAB SECONDARY”.

2 Press [R, T] to select the secondary service and

then press [OK].

To cancel, select “PRIMARY”.

Note:

The setting is cancelled when you select other stations.

Viewing available information

You can view the following information on the display

panel:

Press [DISPLAY].

Checking the signal quality

You can check the signal quality when adjusting the

antenna.

1 Press [PLAY MENU] repeatedly to select

“SIGNAL QUALITY”.

2 Press [OK].

The frequency block followed by the reception quality

is shown.

To select other frequency blocks, press [R, T].

3 Press [OK] again to exit.

Automatic clock adjustment

You can set the clock to update automatically.

1 Press [PLAY MENU] repeatedly to select

“AUTO CLOCK ADJ”.

2 Press [R, T] to select “ON ADJUST” and then

press [OK].

To cancel, select “OFF ADJUST”.

Dynamic label Information about the DAB

broadcast

PTY display Programme type

Ensemble label The name of the ensemble

Frequency display The frequency block and

frequency is shown

Time display Current time

Frequency

block

Frequency Reception quality

0 (poor) to 8 (excellent)

SC-HC302.300 EB.EG TQBJ2071 En.fm Page 10 Monday, January 8, 2018 11:27 AM

TQBJ2071

Clock and timers

Setting the clock

This is a 24-hour clock.

1 Press [SETUP] repeatedly to select “CLOCK”.

2 Press [R, T] to set the time and then press [OK].

To check the time

Press [SETUP] repeatedly to select “CLOCK” and

then press [OK].

In standby mode, press [DISPLAY].

Note:

Reset the clock regularly to maintain accuracy.

Sleep timer

The sleep timer switches off the system after the set time.

1 Press [SETUP] repeatedly to select “SLEEP”.

2 Press [R, T] to select the setting (in minutes) and

then press [OK].

To cancel, select “OFF”.

Note:

• The remaining time is shown at every minute except when

other operations are being performed.

“SLEEP 1” will always be shown when only 1 minute

remains.

• The sleep timer always comes first. Be sure not to set an

overlap of timers.

Play timer

You can set the timer to come on at a certain time to wake

you up.

Preparation

Set the clock.

1 Press [SETUP] repeatedly to select “TIMER ADJ”.

2 Press [R, T] to set the start time and then press

[OK].

3 Repeat step 2 to set the end time.

4 Press [R, T] to select the music source you want

to play and then press [OK].

To start the timer

1 Press [SETUP] repeatedly to select “TIMER SET”.

2 Press [R, T] to select “SET” and then press [OK].

“#” is shown.

To cancel, select “OFF”.

The system must be switched off for the timer to

operate.

To check the setting

Press [SETUP] repeatedly to select “TIMER ADJ” and

then press [OK].

In standby mode, press [DISPLAY] two times.

Note:

• The timer starts at a low volume and increases gradually to

the preset level.

• The timer comes on at the set time every day if the timer is

on.

• If you switch off the system and then switch on again while a

timer is in operation, the timer will not stop at the end time.

•“CD”, “USB”, “DAB+” (“SC-HC302”) and “FM” can be set as

the music source.

Sound effects

1 Press [SOUND] repeatedly to select the sound

effect.

2 Press [R, T] to select the setting and then press

[OK].

Note:

Changed settings will be kept until it is changed again, unless

otherwise indicated.

Saving the sound settings

You can save the current sound effects (up to

3 combinations).

Preparation

Select the sound effects.

1 Press [SETUP] to select “SAVE MY SOUND”.

2 Press [R, T] to select a sound setting number and

then press [OK].

“SAVED” is shown.

The new setting replaces the one existing in the same

sound setting number.

To recall the setting

1 Press [SOUND] to select “MY SOUND”.

2 Press [R, T] to select the sound setting number

and then press [OK].

MY SOUND “SOUND 1”, “SOUND 2” or

“SOUND 3” (~below)

PRESET EQ “HEAVY”, “SOFT”, “CLEAR”,

“VOCAL” or “FLAT”

BASS –4 to +4

TREBLE –4 to +4

D.BASS “ON D.BASS” or “OFF D.BASS”

SURROUND “ON SURROUND” or

“OFF SURROUND”

CLEAR-MODE

DIALOG

“ON CLEAR-MODE DIALOG” or

“OFF CLEAR-MODE DIALOG”

SC-HC302.300 EB.EG TQBJ2071 En.fm Page 11 Monday, January 8, 2018 11:27 AM

TQBJ2071

External music device

You can play music from an external music device.

Preparation

• Switch off the equaliser (if any) of the external music

device to prevent sound distortion.

• Decrease the volume of the system before you connect

or disconnect the external music device.

1 Connect the external music device using an audio

cable (not supplied).

Plug type: Ø 3.5 mm stereo

2 Press [RADIO/AUX] to select “AUX”.

3 Play the external music device.

To adjust the input level

1 Press

[SOUND]

repeatedly to select

“INPUT LEVEL”

2 Press [R, T] to select “LOW” or “HIGH” and then

press [OK].

Note:

• The default setting is “HIGH”.

• Select “LOW” if the sound is distorted during “HIGH” input

level.

• Read the operating instructions of the external music device

for details.

• Components and cables are sold separately.

AUX IN auto play

The system will automatically switch to AUX source when

it detects the signal from an external music device.

This function also works in standby mode.

1 Press [SETUP] repeatedly to select

“AUX-IN AUTO PLAY”.

2 Press [R, T] to select “ON” and then press [OK].

To cancel, select “OFF”.

Note:

• The default setting is “OFF”.

• When the function is switched off and every time you switch

to AUX source, “AUX-IN AUTO PLAY IS OFF” will be shown

once.

• This function does not work when the volume of the external

music device is low, increase its volume.

• Stop or pause the external music device before you change

to other music source or to standby mode so as to prevent

the automatic switch to AUX source.

Others

Auto off

This system automatically switches off when you do not

use it for approximately 20 minutes.

1 Press [SETUP] repeatedly to select “AUTO OFF”.

2 Press [R, T] to select “ON” and then press [OK].

To cancel, select “OFF”.

Note:

This function does not work when you are in radio source or

when a Bluetooth

device is connected.

Bluetooth

standby

This function automatically switches on the system when

you establish a Bluetooth

connection from a paired

device.

1 Press [SETUP] repeatedly to select

“BLUETOOTH STANDBY”.

2 Press [R, T] to select “ON” and then press [OK].

To cancel, select “OFF”.

Charging a device

This system can supply power to a device, such as a

smartphone, connected to the USB port.

Note:

• Use a cable compatible with the device.

• Use the charger supplied with the device if power is not

supplied to the device.

• Do not use a cable or connect a device that exceeds the

rated value of 5 V, 1.5 A.

• Examine the screen of the device to check if charging is

complete. Disconnect the device after charging.

• Once fully charged, remove the USB cable from the USB

port.

• After the device has started charging, you can switch the

unit to standby mode.

– When charging a depleted device, do not switch the unit

to standby mode until the device becomes operational.

• Depending on the device, power may not be supplied to it.

• Read the operating instructions of the device for details.

Software update

Occasionally, Panasonic may release updated software

for this unit that may add or improve the way a feature

operates. These updates are available free of charge.

For more details, refer to the following website.

http://panasonic.jp/support/global/cs/

(This site is in English only.)

█

Checking the software version

1 Press [SETUP] repeatedly to select “SW VER.”

and then press [OK].

The software version is shown.

2 Press [OK] again to exit.

Audio cable

(not supplied)

SC-HC302.300 EB.EG TQBJ2071 En.fm Page 12 Monday, January 8, 2018 11:27 AM

TQBJ2071

Troubleshooting

Before requesting service, make the following checks. If

you are in doubt about some of the check points, or if the

solutions indicated do not solve the problem, consult your

dealer for instructions.

█

Common problems

The unit cannot be switched on.

• Connect the AC mains lead and wait for a minimum of

10 seconds before switching on the unit.

The unit does not work.

• The safety device has been activated. Do the following:

1. Press [1] on the main unit to switch the unit to standby

mode. If the unit does not switch to standby mode,

disconnect the AC mains lead and connect it again.

2. Press [1] again to switch on the unit. If the problem

persists, consult your dealer.

No operations can be done with the remote control.

• Examine that the battery is installed correctly.

Sound is distorted or no sound.

• Adjust the volume of the system.

• Switch off the system, determine and correct the cause, and

then switch on again. It can be caused by straining of the

speakers through excessive volume or power, and when

using the system in a hot environment.

A humming sound can be heard during playback.

• An AC mains lead or fluorescent light is near the cables.

Keep other appliances and cords away from the cables of

this system.

Noise is heard.

• Depending on the device, noise may be heard if the device

is connected to the AUX IN terminal and USB port at the

same time. Disconnect the cable from the USB port.

█

Disc

Display not shown correctly.

Playback does not start.

• You have not put in the disc correctly. Put it in correctly.

• Disc is dirty. Clean the disc.

• Replace the disc if it is scratched, warped, or non-standard.

• There is condensation. Let the system dry for 1 to 2 hours.

The total number of tracks displayed is incorrect.

The disc cannot be read.

Distorted sound is heard.

• You put in a disc that the system cannot play. Change to a

playable disc.

• You put in a disc that has not been finalised.

█

USB

No response when you press [4/9].

• Disconnect the USB device and then connect it again.

Alternatively, switch the unit off and on again.

The USB device or the contents in it cannot be read.

• The format of the USB device or the contents in it are not

compatible with the system.

• USB devices with storage capacity of more than 32 GB

cannot work in some conditions.

Slow operation of the USB device.

• Large content size or large memory USB device takes

longer time to read.

The elapsed time shown is different from the actual play

time.

• Transfer the data to another USB device or backup the data

and reformat the USB device.

█

Bluetooth

Pairing cannot be done.

• Check the Bluetooth

device condition.

• The device is out of the 10 m communication range.

Move the device nearer to the system.

The device cannot be connected.

• The pairing of the device was unsuccessful. Do pairing

again.

• The pairing of the device has been replaced. Do pairing

again.

• This system might be connected to a different device.

Disconnect the other device and try connecting the device

again.

• The system may have a problem. Switch off the system and

then switch on again.

• If “MODE 2” is selected in “LINK MODE”, select “MODE 1”.

(

~7)

The device is connected but audio cannot be heard

through the system.

• For some built-in Bluetooth

devices, you have to set the

audio output to “SC-HC302” or “SC-HC300” manually. Read

the operating instructions of the device for details.

Sound from the device is interrupted.

• The device is out of the 10 m communication range.

Move the device nearer to the system.

• Remove any obstacle between the system and the device.

• Other devices that use the 2.4 GHz frequency band

(wireless router, microwaves, cordless phones, etc.) are

interfering. Move the device nearer to the system and

distance it from the other devices.

• Select “MODE 1” for stable communication. (~7)

█

Radio, DAB/DAB+

Sound is distorted or static is heard.

• Check that the antenna(s) is properly connected. (~ 4)

• Adjust the position of the antenna.

• Keep a certain amount of distance between the antenna

and the AC mains lead.

• Use an outdoor antenna if there are buildings or mountains

nearby.

• Switch off the TV or other audio players or separate it from

the system.

• Keep the system away from mobile phones if there is

interference.

If there is excessive noise during FM reception.

• Change the audio output to monaural. (~9)

DAB/DAB+ reception is poor.

• Keep the antenna away from computers, TV, other cables

and cords.

█

AUX IN

“AUX-IN Auto Play” does not work.

• You have not connected the external music device correctly.

• Increase the volume of the external music device.

• If “OFF” was selected during “AUX-IN AUTO PLAY”, select

“ON”.

Unintentional automatic switch to AUX source.

• Connect the audio cable to the system only after all the

other connections have been made.

Noise may be detected when connecting the external music

device and it will cause the set to automatically switch to

AUX source.

SC-HC302.300 EB.EG TQBJ2071 En.fm Page 13 Monday, January 8, 2018 11:27 AM

TQBJ2071

█

Main unit displays

“--:--”

• You connected the AC mains lead for the first time or there

was a power failure recently. Set the clock.

“ADJUST CLOCK”

• The clock is not set. Adjust the clock.

“ADJUST TIMER”

• The play timer is not set. Adjust the play timer.

“AUTO OFF”

• The system has not been used for 20 minutes and will

switch off within a minute. To cancel, press any button.

“ERROR”

• An incorrect operation was done. Read the instructions and

try again.

“F61”

“F77”

• Disconnect the AC mains lead and consult your dealer.

“F703”

• Examine the Bluetooth

connection.

• Disconnect the Bluetooth

device. Switch off the system

and then switch on again.

“F76”

• There is a problem with the power supply.

• Disconnect the AC mains lead and consult your dealer.

“ILLEGAL OPEN”

• The sliding door is not in a correct position. Switch off the

system and then switch on again.

“NO DEVICE”

• The USB device is not connected. Examine the connection.

“NO DISC”

• You have not put in a disc.

“NO PRESET”

• DAB memory presetting has not been done.

“NO PLAY”

• Examine the content. You can only play supported format.

• The files in the USB device may be corrupted. Format the

USB device and try again.

• The system may have a problem. Switch off the system and

then switch on again.

“NO SIGNAL”

• The station cannot be received. Adjust the antenna.

“PLAYERROR”

• You played an unsupported MP3 file. The system will skip

that track and play the next one.

“LINKING”

• This system is trying to connect to the last connected

Bluetooth

device when “BLUETOOTH” is selected.

“READING”

• The unit is checking the “CD/USB” information. After this

display has disappeared, start operating.

“REMOTE 1”

“REMOTE 2”

• The remote control and the main unit are using different

codes. Change the code of the remote control.

– When “REMOTE 1” is shown, press and hold [OK] and

[ ] for a minimum of 4 seconds.

– When “REMOTE 2” is shown, press and hold [OK] and

[USB/CD] for a minimum of 4 seconds.

“SCAN FAILED”

• Stations cannot be received. Adjust the antenna or perform

the “AUTO SCAN” tuning function. (

~10)

If “SCAN FAILED” is still shown, find the best signal

reception with the “MANUAL SCAN” tuning function.

(

~10)

“SOUND 1 NOT SET”

“SOUND 2 NOT SET”

“SOUND 3 NOT SET”

• You have not saved the sound effects into the sound setting

number.

“USB OVER CURRENT ERROR”

• The USB device is using too much power. Disconnect the

USB device, switch off the system and then switch on again.

“VBR”

• The system cannot show the remaining play time for

variable bit rate (VBR) tracks.

“NOT SUPPORTED”

• You have connected an unsupported USB device.

Remote control code

When other Panasonic equipment responds to the remote

control of this system, change the remote control code for

this system.

Preparation

Press [USB/CD] to select “CD”.

█

To set the code to “REMOTE 2”

1 Press and hold [8] on the main unit and [USB/CD]

on the remote control.

“REMOTE 2” is shown.

2 Press and hold [OK] and [USB/CD] for a minimum

of 4 seconds.

█

To set the code to “REMOTE 1”

1 Press and hold [8] on the main unit and [ ] on

the remote control.

“REMOTE 1” is shown.

2 Press and hold [OK] and [ ] for a minimum of

4 seconds.

System memory reset

Reset the memory when the following situations occur:

• There is no response when buttons are pressed.

• You want to clear and reset the memory contents.

1 Disconnect the AC mains lead.

2 While you press and hold [1] on the main unit,

connect the AC mains lead again.

Continue to press and hold the button until

“–––––––––” is shown.

3 Release [1].

All the settings are set back to the factory preset.

It is necessary to set the memory items again.

Maintenance

Disconnect the AC power supply cord before

maintenance. Clean this system with a soft, dry cloth.

• Never use alcohol, paint thinner or benzine to clean this

system.

• Before using chemically treated cloth, read the

instructions that came with the cloth carefully.

SC-HC302.300 EB.EG TQBJ2071 En.fm Page 14 Monday, January 8, 2018 11:27 AM

TQBJ2071

Specifications

█

Amplifier section

RMS output power stereo mode

Front Ch (both ch driven)

10 W per channel (8 Ω), 1 kHz, 10% THD

Total RMS power 20 W

█

Tuner, terminals section

Preset memory FM 30 stations

Frequency modulation (FM)

Frequency range

87.50 MHz to 108.00 MHz (50 kHz step)

Antenna terminals 75 Ω (unbalanced)

AUX input

Terminal Stereo, 3.5 mm jack

█

DAB section

[HC302]

DAB memories 20 channels

Frequency band (wavelength)

Band III 5A to 13F

(174.928 MHz to 239.200 MHz)

Sensitivity *BER 4x10

-4

Minimum requirement –98 dBm

DAB external antenna

Terminal F - Connector (75 Ω)

█

Disc section

Disc played (8 cm or 12 cm)

CD, CD-R/RW (CD-DA, MP3

)

Pick up

Wavelength 790 nm (CD)

NORSK

Bølgelengde 790 nm (CD)

Laserstyrke Ingen farlig stråling sendes ut

█

USB section

USB port power WDC OUT 5 V 1.5 A

USB standard USB 2.0 full speed

Media file format support MP3 (*.mp3)

Audio support format MP3

Sampling frequency 32/44.1/48 kHz

Audio word size 16 bits

Channel count 2 ch

USB device file system FAT12, FAT16, FAT32

█

Bluetooth

section

Version Bluetooth

Ver. 2.1 + EDR

Class Class 2

Supported profiles A2DP, AVRCP

Frequency band 2.4 GHz band FH-SS

Operation distance 10 m line of sight

Supported codec SBC

█

Speaker section

Speaker unit(s)

Full range 8 cm cone type x 2

█

General

Power supply AC 220 V to 240 V, 50 Hz

Power consumption

14 21 W

Dimensions (W x H x D)

4 409 mm x 198 mm x 107 mm

Mass 2.5 kg

Operating temperature range 0°C to +40°C

Operating humidity range

35% to 80% RH (no condensation)

Note:

• Specifications are subject to change without notice.

Mass and dimensions are approximate.

• Total harmonic distortion is measured by the digital

spectrum analyser.

MPEG-1 Layer 3, MPEG-2 Layer 3

No device is connected to the USB port before switching to

standby mode.

Power consumption in standby mode

(With “BLUETOOTH STANDBY” set to “OFF”)

0.2 W (approximate)

Power consumption in standby mode

(With “BLUETOOTH STANDBY” set to “ON”)

0.3 W (approximate)

SC-HC302.300 EB.EG TQBJ2071 En.fm Page 15 Monday, January 8, 2018 11:27 AM

TQBJ2071

Attaching the unit to a wall (optional)

You can use the supplied wall mount brackets to attach

this unit to the wall.

Preparation

Disconnect the antenna(s) and the AC mains lead.

Installation accessories

█

Supplied accessories

 2 Wall mount brackets

 1 Safety holder

 1 Screw

█

Additional accessories

(commercially available)

 5 Screws

 1 Screw eye

 1 Cord (with a diameter of about 1.5 mm)

Installation instructions

1 Detach the pedestal of the unit.

Put a protection layer below the unit to prevent

scratches.

Remove the screw from the bottom of the unit.

2 Measure and mark the position of the wall mount

brackets on the wall.

Make sure the space on the wall is more than

60 cm (width) by 40 cm (height).

3 Fix the wall mount brackets to the wall.

Use a level to align the wall mount brackets.

4 Fix the safety holder to the unit with the supplied

screw.

5 Attach a cord to the unit to prevent the unit from

falling.

Bend the cord twice from the tip, each at 45° and

5 mm apart for it to go through the holes.

6 Connect the antenna(s) and the AC mains lead

(~4).

7 Hook the unit onto the wall mount brackets.

8 Fix the safety holder to the wall.

Panasonic cannot be held responsible for any property

damage and/or serious injury, including death resulting

from improper installation or incorrect handling.

CAUTION!

• The installation should be done by a competent

installation specialist.

• Keep the wall mount brackets, the safety holder and

the screws out of reach of children to prevent

swallowing.

• Make sure the screws, the cord and the wall can

support the weight of more than 36 kg.

Keep the removed screw and pedestal for future use.

• When using the unit in a non-wall-mounted position

again, be sure to reattach the pedestal to the unit and

secure it with its screw.

Screw

Protection layer

(not supplied)

Pedestal

Wall mount bracket

Screw

(not supplied)

At least 30 mm

Screw

Cord

(not supplied)

Wall

Screw

(not supplied)

SC-HC302.300 EB.EG TQBJ2071 En.fm Page 16 Monday, January 8, 2018 11:27 AM

TQBJ2071

9 Attach the cord to the wall.

References

About Bluetooth

Frequency band

• This system uses the 2.4 GHz frequency band.

Certification

• This system conforms to the frequency restrictions and

has received certification based on frequency laws.

Thus, a wireless permit is not necessary.

• The actions below are punishable by law in some

countries:

– Taking apart or modifying the unit.

– Removing specification indications.

Restrictions of use

• Wireless transmission and/or usage with all Bluetooth

equipped devices is not guaranteed.

• All devices must conform to standards set by the

Bluetooth SIG, Inc.

• Depending on the specifications and settings of a

device, it can fail to connect or some operations can be

different.

• This system supports Bluetooth

security features. But

depending on the operating environment and/or

settings, this security is possibly not sufficient. Transmit

data wirelessly to this system with caution.

• This system cannot transmit data to a Bluetooth

device.

Range of use

• Use this device at a maximum range of 10 m.

• The range can decrease depending on the

environment, obstacles or interference.

Interference from other devices

• This system may not function properly and troubles

such as noise and sound jumps may arise due to radio

wave interference if this unit is located too close to

other Bluetooth

devices or the devices that use the

2.4 GHz band.

• This system may not function properly if radio waves

from a nearby broadcasting station, etc. is too strong.

Intended usage

• This system is for normal, general use only.

• Do not use this system near an equipment or in an

environment that is sensitive to radio frequency

interference (example: airports, hospitals, laboratories,

etc.).

License

Sales and Support Information

For the United Kingdom and Ireland

Customer Communications Centre

• For customers within the UK: 0344 844 3899

• For customers within Ireland: 01 289 8333

• Monday – Friday 9:00am – 5:00pm

(Excluding public holidays).

• For further support on your product, please visit our

website: www.panasonic.co.uk

Direct Sales at Panasonic UK

• Order accessory and consumable items for your

product with ease and confidence by phoning our

Customer Communications Centre

Monday – Friday 9:00am – 5:00pm

(Excluding public holidays).

• Or go on line through our Internet Accessory ordering

application at www.pas-europe.com

• Most major credit and debit cards accepted.

• All enquiries transactions and distribution facilities are

provided directly by Panasonic UK.

• It couldn’t be simpler!

• Also available through our Internet is direct shopping for

a wide range of finished products. Take a browse on our

website for further details.

Panasonic cannot be held responsible for data and/or

information that is compromised during a wireless

transmission.

Cord (not supplied)

Screw eye (not supplied)

Wall

The Bluetooth

word mark and logos are registered

trademarks owned by the Bluetooth SIG, Inc. and any

use of such marks by Panasonic Corporation is under

license. Other trademarks and trade names are those of

their respective owners.

SC-HC302.300 EB.EG TQBJ2071 En.fm Page 17 Monday, January 8, 2018 11:27 AM

TQBJ2071

English

Declaration of Conformity (DoC)

Hereby, “Panasonic Corporation” declares that this

product is in compliance with the essential requirements

and other relevant provisions of Directive 2014/53/EU.

Customers can download a copy of the original DoC to

our RE products from our DoC Server:

http://www.ptc.panasonic.eu

Contact to Authorised Representative:

Panasonic Marketing Europe GmbH, Panasonic Testing

Centre, Winsbergring 15, 22525 Hamburg, Germany

Ελληνικά

∆ήλωση συμμόρφωσης (DoC)

Η “Panasonic Corporation” δηλώνει ότι το προϊόν αυτό

είναι συμμορφωμένο προς τις βασικές απαιτήσεις και

άλλες σχετικές διατάξεις της Οδηγίας 2014/53/EΕ.

Οι πελάτες μπορούν να κατεβάσουν ένα αντίγραφο του

πρωτοτύπου DoC για τα RE προϊόντα μας από τον DoC

server μας:

http://www.ptc.panasonic.eu

Επικοινωνήστε με τον Εξουσιοδοτημένο Αντιπροσωπό

μας

Panasonic Marketing Europe GmbH, Panasonic Testing

Centre, Winsbergring 15, 22525 Hamburg, Γερμανία

Português

Declaração de Conformidade (DoC)

Com o presente documento, a “Panasonic Corporation”

declara que este produto se encontra em conformidade

com os requisitos específicos e demais especificações

referentes à Diretiva 2014/53/UE.

Os clientes podem baixar uma cópia da declaração de

conformidade (DoC) para nossos produtos RE do Server

DoC:

http://www.ptc.panasonic.eu

Contacto com um Representante Autorizado:

Panasonic Marketing Europe GmbH, Panasonic Testing

Centre, Winsbergring 15, 22525 Hamburg, Alemanha

Lietuviškai

Atitikties deklaracija (AD)

Bendrovė “Panasonic Corporation” patvirtina, kad šis

gaminys atitinka direktyvos 2014/53/ES esminius

reikalavimus ir kitas taikytinas nuostatas.

Mūsų RE gaminių originalios atitikties deklaracijos kopiją

klientai gali atsisiųsti iš mūsų AD serverio:

http://www.ptc.panasonic.eu

Įgaliotojo atstovo adresas:

Panasonic Marketing Europe GmbH, Panasonic Testing

Centre, Winsbergring 15, 22525 Hamburg, Vokietija

Slovensko

Izjava o skladnosti (DoC)

“Panasonic Corporation” v tem dokumentu izjavlja, da je

izdelek v skladu z bistvenimi zahtevami in drugimi

pomembnimi določbami Direktive 2014/53/EU.

Stranka lahko naloži izvod izvirnega DoC o naših izdelkih

RE s strežnika DoC:

http://www.ptc.panasonic.eu

Naslov pooblaščenega predstavnika:

Panasonic Marketing Europe GmbH, Panasonic Testing

Centre, Winsbergring 15, 22525 Hamburg, Nemčija

Slovensky

Vyhlásenie o zhode (DoC)

“Panasonic Corporation” týmto vyhlasuje, že tento

výrobok je v súlade so základnými požiadavkami a

ďalšími príslušnými ustanoveniami smernice 2014/53/EÚ.

Zákazníci si môžu stiahnuť kópiu pôvodného DoC na

naše RE výrobky z nášho servera DoC:

http://www.ptc.panasonic.eu

Kontakt na splnomocneného zástupcu:

Panasonic Marketing Europe GmbH, Panasonic Testing

Centre, Winsbergring 15, 22525 Hamburg, Nemecko

Norsk

Samsvarserklæring (DoC)

“Panasonic Corporation” erklærer herved at dette

produktet samsvarer med de grunnleggende kravene og

andre relevante bestemmelser i direktivet 2014/53/EU.

Kundene kan laste ned en kopi av den originale

samsvarserklæringen (DoC) for vårt RE utstyr fra vår DoC

server:

http://www.ptc.panasonic.eu

Kontaktinformasjon autorisert representant:

Panasonic Marketing Europe GmbH, Panasonic Testing

Centre, Winsbergring 15, 22525 Hamburg, Tyskland

Type of wireless

Frequency band

Maximum power

(dBm E.I.R.P.)

Bluetooth

2402 – 2480 MHz 4 dBm

Τύπο ασύρματης

Ζώνη

συχνοτήτων

Μέγιστη ισχύς

(dBm e.i.r.p.)

Bluetooth

2402 – 2480 MHz 4 dBm

Tipo de ligação

sem fios

Banda de

frequência

Potência máxima

(dBm e.i.r.p.)

Bluetooth

2402 – 2480 MHz 4 dBm

Bevielio ryšio

tinklas

Dažnių

diapazonas

Maksimali siuntimo

galia (dBm e.i.r.p.)

Bluetooth

2402 – 2480 MHz 4 dBm

Vrsta brezžiène

povezave

Frekvenčni pas

Največja moč

(dBm EIRP)

Bluetooth

2402 – 2480 MHz 4 dBm

Typ bezdrôtového

pripojenia

Frekvenčné

pásmo

Maximálny výkon

(dBm e.i.r.p.)

Bluetooth

2402 – 2480 MHz 4 dBm

Type trådløs Frekvensbånd

Maks. effekt

(dBm e.i.r.p.)

Bluetooth

2402 – 2480 MHz 4 dBm

SC-HC302.300 EB.EG TQBJ2071 En.fm Page 18 Monday, January 8, 2018 11:27 AM

TQBJ2071

Eesti keel

Vastavusdeklaratsioon (DoC)

Käesolevaga kinnitab “Panasonic Corporation”, et see

toode vastab direktiivi 2014/53/EL olulistele nõuetele ja

teistele asjakohastele sätetele.

Kliendid saavad koopia meie RE toodetele kehtiva

originaalvastavusdeklaratsiooni koopia alla laadida meie

DoC-serveristt:

http://www.ptc.panasonic.eu

Võtke ühendust volitatud esindajaga:

Panasonic Marketing Europe GmbH, Panasonic Testing

Centre, Winsbergring 15, 22525 Hamburg, Saksamaa

Latviski

Atbilstības deklarācija (DoC)

Ar šo “Panasonic Corporation” paziņo, ka šis izstrādājums

atbilst pamatprasībām un pārējiem Direktīvas 2014/53/ES

noteikumiem.

Pircēji var lejupielādēt oriģinālo DoC kopiju mūsu RE

izstrādājumos no mūsu DoC servera:

http://www.ptc.panasonic.eu

Lūdzam sazināties ar pilnvaroto parstāvi:

Panasonic Marketing Europe GmbH, Panasonic Testing

Centre, Winsbergring 15, 22525 Hamburg, Vācijā

Български

Декларация за съответствие (DoC)

С настоящото “Panasonic Corporation” декларира, че

този продукт е в съответствие с

основните изисквания

и други съответни разпоредби на Директива

2014/53/EС.

Потребителите могат да свалят копие от оригиналните

DoC към нашите продуктите от типа RE от сървъра, на

който се съхраняват DoC:

http://www.ptc.panasonic.eu

Свържете се с нашия упълномощен представител:

Panasonic Marketing Europe GmbH, Panasonic Testing

Centre, Winsbergring 15, 22525 Hamburg, Германия

Român

Declaraţie de Conformitate (DoC)

“Panasonic Corporation” declară prin prezenta că acest

produs este conform cu cerinţele esenţiale şi alte

prevederi relevante ale Directivei 2014/53/UE.

Clienţii pot descărca o copie a DoC-ului original al

produselor noastre RE de la adressa noastră DoC din

Internet:

http://www.ptc.panasonic.eu

Contactaţi Reprezentantul Autorizat:

Panasonic Marketing Europe GmbH, Panasonic Testing

Centre, Winsbergring 15, 22525 Hamburg, Germania

Magyar

Megfelelőségi Nyilatkozat (DoC)

Ezennel a, “Panasonic Corporation” kijelenti, hogy a jelen

termék kielégíti az 2014/53/EU Irányelv létfontosságú

követelményeit és más vonatkozó rendelkezéseit.

A vásárlók letölthetik az RE termékek eredeti DoC

másolatát a DoC szerverünkről:

http://www.ptc.panasonic.eu

A hivatalos képviselő elérhetősége:

Panasonic Marketing Europe GmbH, Panasonic Testing

Centre, Winsbergring 15, 22525 Hamburg, Németország

Hrvatski

Deklaracija o podobnosti (DoC)

Ovime, “Panasonic Corporation” izjavljuje da ovaj

proizvod udovoljava osnovnim zahtjevima i ostalim

relevantnim odredbama Direktive 2014/53/EU.

Kupci mogu preuzeti kopiju originalne DoC za naše RE

proizvode s našeg DoC poslužitelja:

http://www.ptc.panasonic.eu

Adresa ovlaštenog predstavništva:

Panasonic Marketing Europe GmbH, Panasonic Testing

Centre, Winsbergring 15, 22525 Hamburg, Njemačka

Türkçe

Uygunluk Beyanı (DoC)

“Panasonic Corporation” bu belge ile bu ürünün

2014/53/EU Direkti’nin temel gerekliliklerine ve diğer ilgili

hükümlerine uygun olduğunu beyan eder.

Müşterilerimiz RE ürünlerimizle ilgili orijinal DoC

belgesinin bir kopyasını DoC sunucumuzdan indirebilir:

http://www.ptc.panasonic.eu

Yetkili Temsilci ile temasa geçin:

Panasonic Marketing Europe GmbH, Panasonic Testing

Centre, Winsbergring 15, 22525 Hamburg, Almanya

Juhtmevaba

seadme

tüüp

Sagedusriba

Maksimaalne

võimsus

(dBm EIRP)

Bluetooth

2402 – 2480 MHz 4 dBm

Bezvadu tips Frekvenču josla

Maksimālā jauda

(dBm EIRP)

Bluetooth

2402 – 2480 MHz 4 dBm

Вид безжична

връзка

Честотна лента

Максимална

мощност

(dBm e.i.r.p.)

Bluetooth

2402 – 2480 MHz 4 dBm

Tip de wireless

Interval de

frecvenţă

Putere maximă

(dBm e.i.r.p.)

Bluetooth

2402 – 2480 MHz 4 dBm

Wireless

típus

Frekvenciasáv

Maximális teljesítmény

(dBm e.i.r.p.)

Bluetooth

2402 – 2480 MHz 4 dBm

Vrsta bežične

mreže

Frekvencijski

pojas

Maksimalna snaga

(dBm e.i.r.p.)

Bluetooth

2402 – 2480 MHz 4 dBm

Kablosuz türü Frekans bandı

Maksimum güç

(dBm e.i.r.p.)

Bluetooth

2402 – 2480 MHz 4 dBm

SC-HC302.300 EB.EG TQBJ2071 En.fm Page 19 Monday, January 8, 2018 11:27 AM

Panasonic Corporation

Web Site: http://www.panasonic.com

█

NORSK

ADVARSEL!

Produkt

• For å redusere faren for brann, elektrisk støt eller

skade på apparatet:

– Dette apparatet må ikke utsettes for regn, fuktighet,

drypp eller sprut.

– Ikke plasser objekter som er fylt med væske, som

vaser, på apparatet.

– Bruk kun anbefalt tilbehør.

– Fjern ikke deksler.

– Dette apparatet må ikke repareres på egen hånd.

Overlat servicearbeider til kvalifisert

servicepersonell.

FORSIKTIG!

Produkt

• For å redusere faren for brann, elektrisk støt eller

skade på apparatet:

– Ikke plasser apparatet i en bokhylle, et innebygget

kabinett eller et annet lukket sted. Pass på at

apparatet er godt ventilert.

– Apparatets ventilasjonsåpninger må ikke dekkes til

med aviser, duker, gardiner eller lignende.

– Plasser ikke åpen ild, slik som levende lys, oppå

apparatet.

• Dette apparatet er beregnet til bruk under moderate

klimaforhold.

• Dette apparatet anvender en laser. Betjening av

kontroller, justeringer eller andre inngrep enn de som

er beskrevet i denne bruksanvisning, kan føre til farlig

bestråling.

Vekselstrømnett

• Støpselet er frakoblende enhet. Strømuttaket må

befinne seg i nærheten slik at støpselet lett kan kobles

ut fra uttaket umiddelbart.

Disposal of Old Equipment and Batteries

Only for European Union and countries with

recycling systems

These symbols on the products, packaging,

and/or accompanying documents mean that

used electrical and electronic products and

batteries must not be mixed with general

household waste.

For proper treatment, recovery and recycling

of old products and used batteries, please

take them to applicable collection points in

accordance with your national legislation.

By disposing of them correctly, you will help

to save valuable resources and prevent any

potential negative effects on human health

and the environment.

For more information about collection and

recycling, please contact your local

municipality.

Penalties may be applicable for incorrect

disposal of this waste, in accordance with

national legislation.

Note for the battery symbol (bottom symbol):

This symbol might be used in combination

with a chemical symbol. In this case it

complies with the requirement set by the

Directive for the chemical involved.

TQBJ2071

L0218KE1028

Manufactured by:

Importer for Europe:

Panasonic Corporation

Kadoma, Osaka, Japan

Panasonic Marketing Europe GmbH

Panasonic Testing Centre

Winsbergring 15, 22525 Hamburg, Germany

SC-HC302.300 EB.EG TQBJ2071 En.fm Page 20 Monday, January 8, 2018 11:27 AM

Panasonic SCHC300EG Instrucțiuni de utilizare

Marca: Panasonic

Model: SCHC300EG

Tip: Instrucțiuni de utilizare

Acest manual este potrivit și pentru

Descărcați PDF

raport

în alte limbi

English: Panasonic SCHC300EG Operating instructions

Panasonic SCHC300EG Instrucțiuni de utilizare

Acest manual este potrivit și pentru

Panasonic SCHC300EG Instrucțiuni de utilizare

în alte limbi

Lucrări conexe

Alte documente