Furuno GP-320B Manualul proprietarului

Marca: Furuno

Model: GP-320B

Tip: Manualul proprietarului

GPS RECEIVER

GP-320B

OPERATOR'S MANUAL

www.furuno.com

Model

Ni-Cd Pb

IMPORTANT NOTICES

General

• This manual has been authored with simplified grammar, to meet the needs of

international users.

• The operator of this equipment must read and follow the instructions in this manual.

Wrong operation or maintenance can void the warranty or cause injury.

• Do not copy any part of this manual without written permission from FURUNO.

• If this manual is lost or worn, contact your dealer about replacement.

• The contents of this manual and the equipment specifications can change without

notice.

• The example screens (or illustrations) shown in this manual can be different from the

screens you see on your display. The screens you see depend on your system

configuration and equipment settings.

• Save this manual for future reference.

• Any modification of the equipment (including software) by persons not authorized by

FURUNO will void the warranty.

• The following concern acts as our importer in Europe, as defined in DECISION No

768/2008/EC.

- Name: FURUNO EUROPE B.V.

- Address: Ridderhaven 19B, 2984 BT Ridderkerk, The Netherlands

• All brand, product names, trademarks, registered trademarks, and service marks belong

to their respective holders.

How to discard this product

Discard this product according to local regulations for the disposal of industrial waste. For

disposal in the USA, see the homepage of the Electronics Industries Alliance

(http://www.eiae.org/) for the correct method of disposal.

How to discard a used battery

Some FURUNO products have a battery(ies). To see if your product has a battery, see the

chapter on Maintenance. Follow the instructions below if a battery is used. Tape the + and -

terminals of battery before disposal to prevent fire, heat generation caused by short circuit.

In the European Union

The crossed-out trash can symbol indicates that all types of

batteries must not be discarded in standard trash, or at a trash

site. Take the used batteries to a battery collection site

according to your national legislation and the Batteries Directive

2006/66/EU.

In the USA

The Mobius loop symbol (three chasing arrows) indicates that

Ni-Cd and lead-acid rechargeable batteries must be recycled.

Take the used batteries to a battery collection site according to

local laws.

In the other countries

There are no international standards for the battery recycle symbol. The number of symbols

can increase when the other countries make their own recycling symbols in the future.

SAFETY INSTRUCTIONS

Confirm that the power supply voltage

is compatible with the voltage rating

of the equipment.

Connection to the wrong power supply can

cause fire or damage the equipment.

CAUTION NOTICE

No one navigation device should ever

be solely relied upon for the navigation

of a vessel.

Always confirm position against all

available aids to navigation, for safety of

vessel and crew.

iii

TABLE OF CONTENTS

SYSTEM OVERVIEW........................................................................................... iv

EQUIPMENT LISTS ............................................................................................. vi

1. MOUNTING ....................................................................................................... 1

2. WIRING ............................................................................................................. 2

3. DEFAULT SETTINGS ....................................................................................... 6

4. TROUBLESHOOTING, BATTERY.................................................................... 7

SPECIFICATIONS........................................................................................... SP-1

PACKING LIST.................................................................................................. A-1

OUTLINE DRAWING ........................................................................................ D-1

SYSTEM OVERVIEW

The GP-320B is a GPS receiver with WAAS (Wide Area Augmentation System) capability.

WAAS, available in North America, is a provider in the worldwide SBAS (Satellite Based

Augmentation System) navigation system. This system provides GPS signal corrections to

SBAS users, for even better position accuracy, typically better than three meters. There are

three more SBAS providers, MSAS (Multi-Functional Satellite Augmentation System) for Japan,

EGNOS (Euro Geostationary Navigation Overlay Service) for Europe and GAGAN (GPS And

GEO Augmented Navigation) for India. The illustration below shows the coverage area.

(Accuracy may be affected when using a GEO satellite not within your current location.) This

manual uses “WAAS” for these three providers generically.

WAAS

MSAS

EGNOS

GAGAN

Provider Satellite type Longitude Satellite No.

Intelsat Galaxy XV 133°W 135

TeleSat Anik F1R 107.3° 138

WAAS

Inmarsat-4-F3 98°W 133

Inmarsat-3-F2/AOR-E 15.5°W 120

Artemis 21.5°E 124

EGNOS

Inmarsat-4-F2 25°E 126

MTSAT-1R 140°E 129

MSAS MTSAT-2 145°E 137

GAGAN Inmarsat-4-F1 64°E 127

Other Equipment*

JUNCTION BOX

GD-XXXX

GR-80

Ship's Mains (12-24 VDC)

Multi Display RD-30*

Echo Sounder LS-6100

NavNet Series

Model 1722C Model 1833C

Model 1722 Model 1933C

Model 1732C Model 1943C

Model 1732 Model 1833

Model 1742C Model 1933

Model 1742 Model 1943

Model 1752C Model 1953C

Model 1752 GD-1900C

Model 1762C GD-1700C

Model 1762 GD-1700

* = WAAS is inoperative.

This GPS receiver complies with Canadian standard RSS-210 (Low Power

License-Exempt Radio communication Devices).

Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may

cause undesired operation of the device.

Program No.

4850264***

** denotes minor modifications.

CE declaration

With regards to CE declarations, please refer to our website (www.furuno.com), for further

information about RoHS conformity declarations.

EQUIPMENT LISTS

Standard supply

Name Type Code No. Qty Remarks

GPS Receiver GP-320B ⎯ 1 With 10 m cable

Optional equipment

Name Type Code No. Qty Remarks

Cable Assembly MJ-A7SPF/SRMD-100 000-144-534 1 7P-7P, straight,

10 m

Mast Mounting Kit CP20-01111 004-365-780 1

Right Angle

Antenna Base NO.13-QA330 000-803-239 1

L-angle Antenna

Base NO.13-QA310 000-803-240 1

Handrail-mount

Antenna Base NO.13-RC5160 000-806-114 1

1. MOUNTING

NOTICE

Do not apply paint, anti-corrosive

sealant or contact spray to coating or

plastic parts of the equipment.

Those items contain organic solvents that

can damage coating and plastic parts,

especially plastic connectors.

Mounting considerations

Follow the guidelines below to choose a suitable mounting location for the antenna unit.

• The antenna may be mounted three ways: screwed into a pipe (local supply), fixed to a

post with the optional mast mounting kit, or screwed into an optional mounting base. For

fixing by the post or pipe, it is recommended to use stays to prevent damage to the GPS

receiver.

• Select a location out of the radar beam. The radar beam will obstruct or prevent

reception of the GPS signal.

• The location should be well away from a VHF antenna. A GPS receiver is interfered by a

harmonic wave of a VHF antenna.

• The location should be well away from an Inmarsat antenna. Inmarsat transmission will

obstruct or prevent reception of the GPS signal.

• There should be no interfering object within the line-of-sight to the satellites. Objects

within line-of-sight to a satellite, for example, a mast, may block reception or prolong

acquisition time.

• Mount the antenna unit as high as possible to keep it free of interfering objects and

water spray, which can obstruct reception of the GPS signal if the water freezes.

• Observe the following minimum separation distances from other antenna units.

1.5 m

MAIN MAST

TX ANTENNA(MF/HF)

NOT WITHIN RADAR BEAM

* = DISTANCE DEPENDS ON MAST DIAMETER OF ’a’.

4 m

1 m1 m

3 m

INMARSAT ANTENNA

LOOP ANTENNA

RX WHIP ANTENNA

5 m

NOT WITHIN INMARSAT BEAM

0.5 m

WHIP ANTENNA(VHF/UHF) WHIP ANTENNA(MF/HF)

GPS ANTENNA

DIA. OF ’a’ DISTANCE (MIN.)

3 m

1.5 m

10 cm

30 cm

Mounting procedure

Install the antenna unit by referring to the installation diagram on page D-1.

2. WIRING

This unit outputs position and speed to external equipment. NavNet equipment, Multi

Display RD-30 and Echo Sounder LS-6100 can be connected directly. For connection to

other equipment, use a junction box (local supply) which has seven terminals.

The antenna cable is 10 meters long. If the distance between the antenna unit and the

display monitor is more than 10 meters, use the optional cable assy. (10 m). Up to four

extension cables can be connected serially.

Connecting to FURUNO NavNet equipment

Connect the antenna cable to the DATA1 port on NavNet equipment.

Total length: Max. 50 m

Cable assy. (option)

MJ-A7SPF/SRMD-100

10 m (max. 4)

Antenna Cable

10 m

DATA 1 port

NavNet

Waterproofing connectors

If you use the cable assy.(s), waterproof their connectors by wrapping them with vulcanizing

tape and then vinyl tape. Bind tape ends with suitable cable-ties.

Connecting to Multi Display RD-30

WAAS is not operative in this installation.

Antenna Cable

10 m

MULTI DISPLAY

RD-30

AUX port

IN/OUT port

12-24 VDC

AUX

IN/OUT

12-24

VDC

Rear Panel

Connecting to Echo Sounder LS-6100

Antenna Cable

10 m ECHO SOUNDER

LS-6100

REAR

NMEA

XDR

POWER

12VDC

POWER

12 VDC

NMEA

Connecting to other equipment

Remove the connector from the antenna cable and attach crimp-on lugs or similar terminals

to the cable’s cores. Connect the cores to the junction box as below.

Antenna Cable

10 m non-NavNet equipment

RS-422*

input for radar/plotter

Correction data from GR-80

output in RS-422 format

12-24 VDC*

(Input current: 105-55 mA)

NMEA 0183 Ver. 2.0

*1: RS-422 signal can

be received by using

current loop.

WHITE

BLACK

YELLOW

JUNCTION BOX

GREEN

RED

BLUE

Drain Wire

Fuse 0.5 A

RD-A

RD-B

TD-A

TD-B

Switchboard breaker

*2: Supply from breaker on switchboard

Note 1: When connecting FURUNO DGPS beacon receiver GR-80 to this unit, set it as

follows:

Byte Format, 8-6; First Bit, LSB; Parity Bit, None; Stop Bit, 1; Bit Rate, 8.

Note 2: The signal ground and frame ground are separated, however the power line is not

isolated. Therefore, do not connect the signal ground to the frame ground when

other equipment is connected to a positive ground battery.

Note 3: WAAS function is inoperative when wiring as shown above.

Output/Input data sentences

Priority Input Data Output Data

Settable

Output

Cycle

Default

Output

GPDTM Geometric datum Yes Yes

XXGGA GPS position

status (time of fix,

latitude, longitude,

receive status,

satellite used)

GPGGA GPS fix data Yes Yes

XXZDA UTC date (time in

minutes and

seconds, day,

month, year, time)

GPZDA UTC time and date Yes Yes

XXGLL Position (latitude,

longitude)

GPGLL Geographic

position, latitude

and longitude

Yes Yes

GPVTG Course over

ground and ground

speed

Yes Yes

High

↑

↓

Low

XXRMC Navigation data

(UTC time and

latitude, longitude,

ground speed,

true course, year,

month, day)

GPRMC Recommended

minimum specific

GPS/TRANSIT

data

Yes Yes

Note 1: Data output from high to low priority.

Note 2: GPDTM data is attached in front of GPGGA, GPGLL and GPRMC when those

sentences are output.

Note 3: “XX” means talker ID.

3. DEFAULT SETTINGS

Setting Default setting Backup

Initial Latitude/Longitude North=34°44.0000, East=135°21.0000 Yes

Date, Time 2001/1/1, 00:00:13 Yes

Antenna Height 0 m Yes

Almanac Data ⎯ Yes

Ephemeris Data ⎯ Yes

Local Zone Time +0 Yes

PDOP 6 Yes

Geometric Datum WGS84 Yes

Mask Elevation 5° Yes

Disable Satellite None No

Smoothing Coefficient 2 (Standard) No

Dynamic Coefficient 2 (Standard) No

Data Output (Cycle) DTM, GGA, ZDA, GLL, VTG, RMC (1 s) Yes

DGPS Setting Parameter 1 (LSB first) Yes

GEO Satellite, Provider ID Auto: from 120, in sequential order No

WAAS Availability OFF No

Type 0 Message 0: Correct data not output for 60 s Yes

4. TROUBLESHOOTING, BATTERY

Troubleshooting

If the message “No position data” appears on the display of NavNet equipment, there may

be a problem with the GPS receiver. Turn off the power and then check the following points:

1) Check for objects around the antenna which may interfere with reception.

2) Check that the antenna cable is firmly fastened.

3) If extension cable(s) are used, check for water leakage at junction point(s).

4) Check the antenna cable for damage.

5) Check the antenna for damage.

If the problem seems to be with the antenna cable or antenna, contact your dealer.

Battery

The antenna unit contains a lithium battery which preserves data when the power is turned

off, and its life is approximately 20 years (operating rate 70%) for large vessels and 10

years (operating rate 20%) for small vessels. The equipment can be used when the voltage

of the battery is low, however data is not backed up and the unit starts up in the “cold start”

condition.

FURUNO

GP-320B

SP - 1 E4422S01C

201105

SPECIFICATIONS OF GPS RECEIVER

GP-320B

1 GENERAL

1.1 Receiving channels

GPS 12 channels parallel, 12 satellites tracking

WAAS 1 channel

1.2 Rx frequency 1575.42 MHz

1.3 Rx code C/A code, WAAS

1.4 Position accuracy

GPS 10 m (95% of the time, HDOP 4)

DGPS 5 m (95% of the time, external data required)

WAAS 3 m (95% of the time)

1.5 Tracking velocity 999 kt

1.6 Position-fixing time Warm start: 12 s approx., Cold start: 90 s approx.

1.7 Position update interval 1 s

2 INTERFACE

2.1 Data format IEC 61162-1 (NMEA 0183 Ver 2.30)

2.2 Data sentences

Input DGPS: RTCM SC-104, Control command

Output DTM, GGA, GLL, RMC, VTG, ZDA (default setting)

3 POWER SUPPLY

12-24 VDC (10.8-31.2 V): 105-55 mA

4 ENVIRONMENTAL CONDITION

4.1 Ambient temperature -25°C to +70°C

4.2 Relative humidity 95% at 40°C

4.3 Degree of protection IPX6

4.4 Vibration IEC 60945

5 UNIT COLOR

N9.5

ＰＡＣＫＩＮＧ　ＬＩＳＴ

20AW-X-9852 -1

GP-320B（E)

N A M E O U T L I N E DESCRIPTION/CODE № Q'TY

1/1

ユニット UNIT

GPS受信機

GPS RECEIVER

GP-320B(E)

004-367-500-00

図書 DOCUMENT

取扱説明書

OPERATOR'S MANUAL

OME-44220-*

000-809-291-1*

（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

型式/ｺｰﾄﾞ番号が２段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。　なお、品質は変わりません。

TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER

PRODUCT. QUALITY IS THE SAME.

A-1

D-1

Sep.20 '02

FURUNO Worldwide Warranty for Pleasure Boats (Except North America)

This warranty is valid for products manufactured by Furuno

Electric Co. (hereafter FURUNO) and installed on a pleasure

boat. Any web based purchases that are imported into other

countries by anyone other than a FURUNO certified dealer may

not comply with local standards. FURUNO strongly recommends

against importing these products from international websites as

the imported product may not work correctly and may interfere

with other electronic devices. The imported product may also be

in breach of the local laws and mandated technical requirements.

Products imported into other countries as described previously

shall not be eligible for local warranty service.

For products purchased outside of your country please contact

the national distributor of Furuno products in the country where

purchased.

This warranty is in addition to the customer´s statutory legal

rights.

1. Terms and Conditions of Warranty

FURUNO guarantees that each new FURUNO product is the

result of quality materials and workmanship. The warranty is

valid for a period of 2 years (24 months) from the date of the

invoice, or the date of commissioning of the product by the

installing certified dealer.

2. FURUNO Standard Warranty

The FURUNO standard warranty covers spare parts and labour

costs associated with a warranty claim, provided that the product

is returned to a FURUNO national distributor by prepaid carrier.

The FURUNO standard warranty includes:

 Repair at a FURUNO national distributor

 All spare parts for the repair

 Cost for economical shipment to customer

3. FURUNO Onboard Warranty

If the product was installed/commissioned and registered by a

certified FURUNO dealer, the customer has the right to the

onboard warranty.

The FURUNO onboard warranty includes

• Free shipping of the necessary parts

• Labour: Normal working hours only

• Travel time: Up to a maximum of two (2) hours

• Travel distance: Up to a maximum of one hundred

and sixty (160) KM by car for the complete journey

4. Warranty Registration

For the Standard Warranty - presentation of product with serial

number (8 digits serial number, 1234-5678) is sufficient.

Otherwise, the invoice with serial number, name and stamp of

the dealer and date of purchase is shown.

For the Onboard Warranty your FURUNO certified dealer will

take care of all registrations.

5. Warranty Claims

For the Standard Warranty - simply send the defective product

together with the invoice to a FURUNO national distributor.

For the Onboard Warranty – contact a FURUNO national

distributor or a certified dealer. Give the product´s serial number

and describe the problem as accurately as possible.

Warranty repairs carried out by companies/persons other than a

FURUNO national distributor or a certified dealer is not covered

by this warranty.

6. Warranty Limitations

When a claim is made, FURUNO has a right to choose whether

to repair the product or replace it.

The FURUNO warranty is only valid if the product was correctly

installed and used. Therefore, it is necessary for the customer to

comply with the instructions in the handbook. Problems which

result from not complying with the instruction manual are not

covered by the warranty.

FURUNO is not liable for any damage caused to the vessel by

using a FURUNO product.

The following are excluded from this warranty:

a. Second-hand product

b. Underwater unit such as transducer and hull unit

c. Routine maintenance, alignment and calibration

services.

d. Replacement of consumable parts such as fuses,

lamps, recording papers, drive belts, cables, protective

covers and batteries.

e. Magnetron and MIC with more than 1000 transmitting

hours or older than 12 months, whichever comes first.

f. Costs associated with the replacement of a transducer

(e.g. Crane, docking or diver etc.).

g. Sea trial, test and evaluation or other demonstrations.

h. Products repaired or altered by anyone other than the

FURUNO national distributor or an authorized dealer.

i. Products on which the serial number is altered,

defaced or removed.

j. Problems resulting from an accident, negligence,

misuse, improper installation, vandalism or water

penetration.

k. Damage resulting from a force majeure or other natural

catastrophe or calamity.

l. Damage from shipping or transit.

m. Software updates, except when deemed necessary

and warrantable by FURUNO.

n. Overtime, extra labour outside of normal hours such as

weekend/holiday, and travel costs above the 160 KM

allowance

o. Operator familiarization and orientation.

FURUNO Electric Company, March 1, 2011

FURUNO Warranty for North America

FURUNO U.S.A., Limited Warranty provides a twenty-four (24) months LABOR and twenty-four (24) months PARTS

warranty on products from the date of installation or purchase by the original owner. Products or components that are

represented as being waterproof are guaranteed to be waterproof only for, and within the limits, of the warranty

period stated above. The warranty start date may not exceed eighteen (18) months from the original date of purchase

by dealer from Furuno USA and applies to new equipment installed and operated in accordance with Furuno USA’s

published instructions.

Magnetrons and Microwave devices will be warranted for a period of 12 months from date of original equipment

installation.

Furuno U.S.A., Inc. warrants each new product to be of sound material and workmanship and through its authorized

dealer will exchange any parts proven to be defective in material or workmanship under normal use at no charge for a

period of 24 months from the date of installation or purchase.

Furuno U.S.A., Inc., through an authorized Furuno dealer will provide labor at no cost to replace defective parts,

exclusive of routine maintenance or normal adjustments, for a period of 24 months from installation date provided the

work is done by Furuno U.S.A., Inc. or an AUTHORIZED Furuno dealer during normal shop hours and within a radius

of 50 miles of the shop location.

A suitable proof of purchase showing date of purchase, or installation certification must be available to Furuno U.S.A.,

Inc., or its authorized dealer at the time of request for warranty service.

This warranty is valid for installation of products manufactured by Furuno Electric Co. (hereafter FURUNO). Any

purchases from brick and mortar or web-based resellers that are imported into other countries by anyone other than a

FURUNO certified dealer, agent or subsidiary may not comply with local standards. FURUNO strongly recommends

against importing these products from international websites or other resellers, as the imported product may not work

correctly and may interfere with other electronic devices. The imported product may also be in breach of the local

laws and mandated technical requirements. Products imported into other countries, as described previously, shall not

be eligible for local warranty service.

For products purchased outside of your country please contact the national distributor of Furuno products in the

country where purchased.

WARRANTY REGISTRATION AND INFORMATION

To register your product for warranty, as well as see the complete warranty guidelines and limitations, please visit

www.furunousa.com and click on “Support”. In order to expedite repairs, warranty service on Furuno equipment is

provided through its authorized dealer network. If this is not possible or practical, please contact Furuno U.S.A., Inc.

to arrange warranty service.

FURUNO U.S.A., INC.

Attention: Service Coordinator

4400 N.W. Pacific Rim Boulevard

Camas, WA 98607-9408

Telephone: (360) 834-9300

FAX: (360) 834-9400

Furuno U.S.A., Inc. is proud to supply you with the highest quality in Marine Electronics. We know you had several

choices when making your selection of equipment, and from everyone at Furuno we thank you. Furuno takes great

pride in customer service.

Pagina se încarcă ...

Furuno GP-320B Manualul proprietarului

Marca: Furuno

Model: GP-320B

Tip: Manualul proprietarului

Descărcați PDF

raport

în alte limbi

English: Furuno GP-320B Owner's manual
italiano: Furuno GP-320B Manuale del proprietario

Lucrări conexe

Furuno GP330B Manual de utilizare

Furuno GP-320B Manualul proprietarului

Furuno GP-320B Manualul proprietarului

în alte limbi

Lucrări conexe

Alte documente