Yamaha R-N500 Silver Manual de utilizare

Printed in Malaysia ZH44740

Network Receiver

Réseau Ampli-Tuner

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

G

_R-N500_G_cv.fm Page 1 Tuesday, July 30, 2013 10:47 AM

Caution: Read this before operating your unit.

i En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean

place – away from direct sunlight, heat sources, vibration,

dust, moisture, and/or cold. For proper ventilation, allow the

following minimum clearances.

Top: 30 cm (11-3/4 in)

Rear: 20 cm (7-7/8 in)

Sides: 20 cm (7-7/8 in)

3 Locate this unit away from other electrical appliances, motors,

or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in an environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign objects may fall onto

this unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to

this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections

are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may

cause fire, damage to this unit, and/or personal injury. Yamaha

will not be held responsible for any damage resulting from use

of this unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power cord

disconnected from a wall outlet or the unit during a lightning

storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed. The

cabinet should never be opened for any reasons.

15

When not planning to use this unit for long periods of time (i.e.

vacation), disconnect the AC power plug from the wall outlet.

16 Be sure to read the “Troubleshooting” section in the owner’s

manual on common operating errors before concluding that

this unit is faulty.

17 Before moving this unit, press A downward to turn off this

unit and then disconnect the AC power plug from the AC wall

outlet.

18 Condensation will form when the surrounding temperature

changes suddenly. Disconnect the power cable from the

outlet, then leave this unit alone.

19 When using this unit for a long time, this unit may become

warm. Turn the system off, then leave this unit alone for

cooling.

20 Install this unit near the wall outlet and where the AC power

plug can be reached easily.

21 The batteries shall not be exposed to excessive heat such as

sunshine, fire or the like. When you dispose of batteries,

follow your regional regulations.

22 Excessive sound pressure from earphones and headphones

can cause hearing loss.

This label is required to be attached to a product of which the

temperature of the top cover may be hot during operation.

Caution: Read this before operating your unit.

As long as this unit is connected to the AC wall outlet, it is not

disconnected from the AC power source even if you set this unit to

standby mode by A. In this state, this unit is designed to consume a

very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

English

1 En

PREPARATIONINTRODUCTION

BASIC

OPERATION

ADDITIONAL

INFORMATION

ADVANCED

OPERATION

English

INTRODUCTION

Useful features ............................................................ 2

Supplied accessories ................................................... 3

Controls and functions ............................................... 4

Front panel ..................................................................... 4

Front display .................................................................. 6

Rear panel ...................................................................... 7

Remote control............................................................... 8

Using the remote controls.............................................. 9

PREPARATION

Connections............................................................... 10

Connecting speakers and source components.............. 10

Connecting the speakers .............................................. 11

Connecting the FM and AM antennas ......................... 12

Connecting to a network.............................................. 13

Connecting power cable .............................................. 13

BASIC OPERATION

Playback .................................................................... 14

Playing a source........................................................... 14

Using the sleep timer ................................................... 16

Listening to FM/AM radio....................................... 17

FM/AM tuning............................................................. 17

Automatic preset tuning (FM stations only)................ 18

Manual tuning preset ................................................... 18

Recalling a preset station ............................................. 19

Clearing a preset station............................................... 19

Radio Data System tuning ........................................... 20

Playing back iPod music .......................................... 21

Connecting an iPod...................................................... 21

Playback of iPod content ............................................. 21

Playing back music stored

on a USB storage device....................................... 23

Connecting a USB storage device ............................... 23

Playback of USB storage device contents ................... 23

Playing back music stored

on media servers (PCs/NAS)................................ 25

Setting the media sharing of music files...................... 25

Playback of PC music contents.................................... 26

Listening to Internet radio....................................... 27

Playing back iTunes/iPod music

via a network (AirPlay)........................................ 28

Playback of iTunes/iPod music contents ..................... 28

Switching information on the front display ........... 29

ADVANCED OPERATION

Configuring playback settings for different

playback sources (OPTION menu)......................30

OPTION menu items ................................................... 30

Configuring various functions (SETUP menu) ......31

SETUP menu items ..................................................... 31

Network Setup ............................................................. 32

Max Volume ................................................................ 33

Initial Volume.............................................................. 33

AutoPowerStdby.......................................................... 33

ECO Mode................................................................... 33

DC OUT ...................................................................... 33

Configuring the system settings

(ADVANCED SETUP menu)...............................34

ADVANCED SETUP menu items .............................. 34

Changing the speaker impedance setting (SP IMP.) ... 34

Selecting the remote control ID (REMOTE ID).......... 34

Restoring the default settings (INIT)........................... 35

Updating the firmware (UPDATE) ............................. 35

Checking the firmware version (VERSION)............... 35

Controlling external devices

with the remote control.........................................36

Registering the remote control code for a TV ............. 36

Registering the remote control codes

for playback devices................................................ 37

Resetting remote control codes.................................... 38

Updating the unit’s firmware via the network.......39

ADDITIONAL INFORMATION

Troubleshooting.........................................................40

Error indications on the front display.....................45

Trademarks ...............................................................46

Specifications .............................................................47

Index...........................................................................48

(at the end of this manual)

Information about software ................................... i

LIST OF REMOTE CONTROL CODES .................. v

Contents

Useful features

2 En

This unit allows you to:

Easy operation and wireless music playback from iPhone or Android device.

By using the application for smartphone /tablet “NP Controller”, you can control the unit from an iPhone, iPad, iPod

touch or Android devices.

Features

• Basic operations such as turning the power on/off and adjusting the volume

• Switching the input source

• Displaying FM tuner information

• Selecting songs and starting/stopping playback

• Playing back music from the iPhone or Android device

• To download the application or see the latest information, access the App Store or Google Play and search for “NP Controller.”

For details, please visit Yamaha website.

Useful features

Play back music from your iPod and USB devices

➡

p.21, 23

Play back music from network sources (PC/NAS, AirPlay)

➡

p.25, 28

Listen to network streaming services

➡

p.27

Listen to FM and AM radio stations

➡

p.17

Boost bass sounds by connecting a subwoofer

➡

p.10

Configure speaker impedance

➡

p.11

Use this unit’s remote control to operate other components such

as a CD player, BD/DVD player or TV

➡

p.36

Use this unit to eco mode (power saving function)

➡

p.33

• y indicates a tip for your operation.

• This manual explains operations using the supplied remote control.

• This manual describes all the “iPod”, “iPhone” and “iPad” as the “iPod”. “iPod” refers to “iPod”, “iPhone” and “iPad”, unless

otherwise specified.

INTRODUCTION

Supplied accessories

3 En

INTRODUCTION

English

Check that the following accessories are supplied with the product.

■ Notes on remote controls and batteries

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following conditions:

– places of high humidity, such as near a bath

– places of high temperatures, such as near a heater or stove

– places of extremely low temperatures

– dusty places

• Insert batteries according to the polarity markings (+ and -).

• Change all batteries if you notice the operation range of the remote control narrows.

• If the batteries run out, immediately remove them from the remote control to prevent an explosion or acid leak.

• If you find leaking batteries, discard the batteries immediately, taking care not to touch the leaked material. If the leaked material

comes into contact with your skin or gets into your eyes or mouth, rinse it away immediately and consult a doctor. Clean the battery

compartment thoroughly before installing new batteries.

• Do not use old batteries together with new ones. This may shorten the life of the new batteries or cause old batteries to leak.

• Do not use different types of batteries (such as alkaline and manganese batteries) together. Read the packaging carefully as these

different types of batteries may have the same shape and color.

• Before inserting new batteries, wipe the battery compartment clean.

• Keep the batteries in a location out of reach of children. Batteries can be dangerous if a child were to put in his or her mouth.

• If the batteries grow old, the effective operation range of the remote control decreases considerably. If this happens, replace the

batteries with new one as soon as possible.

• If you plan not to use the unit for a long period of time, remove the batteries from the unit. Otherwise, the batteries will wear out,

possibly resulting in a leakage of battery liquid that may damage the unit.

• Do not throw away batteries with general house waste. Dispose of them correctly in accordance with your local regulations.

Supplied accessories

SOURCE

ID

RECEIVER

CODE SET

SLEEP

DIMMER

SPEAKERS

A B

TV INPUT

TV VOL TV CH

TV MUTE

TV

COAX1

COAX2

OPT1

OPT2

LINE1 LINE2 LINE3

SHUFFLE

REPEAT

MODE

PHONO

TUNER

CD

FM AM

DISC SKIP

PRESET TUNING

MEMORY

SETUP

OPTION

RETURN

TOP

MENU

1

2 3 4

5

6 7 8

9

0

10

ENT

POP-UP

MENU

MUTE

ENTER

VOLUME

HOME

NOW

PLAYING

USB

NET

DISPLAY

+

Remote control

FM antennaAM antenna

Batteries (x2)

(AAA, R03, UM-4)

Controls and functions

4 En

1 A (power)

Turns on/off (standby) the unit.

In standby mode, this unit consumes a small amount of power to

receive infrared signals from the remote control.

2 Power indicator

Lights up as follows:

Brightly lit: Power is on

Dimly lit: Standby mode

3 Remote control sensor

Receives infrared signals from the remote control.

Switch the remote control ID between ID1 and ID2 when using

multiple Yamaha receivers or amplifiers (p.34).

4 DIMMER

Changes the brightness level of the front display. Choose

brightness from 5 levels by pressing this button

repeatedly.

y

This setting is retained even if you turn off this unit.

5 DISPLAY

Selects the information displayed on the front display

(p.29).

6 MEMORY

Stores the current FM/AM station as a preset when

TUNER is selected as the input source (p.18).

7 CLEAR

Clears a FM/AM preset station when TUNER is selected

as the input source (p.19).

8 Front display

Shows information about the operational status of this

unit.

9 PRESET j / i

Selects a preset FM/AM station when TUNER is selected

as the input source (p.19).

0 FM and AM keys

Switch between FM and AM (p.17).

A TUNING jj / ii

Selects the tuning frequency when TUNER is selected as

the input source (p.17).

B PURE DIRECT and indicator

Allows you to listen to a source in the purest possible

sound (p.14). The indicator above it lights up and the front

display turns off when this function is turned on.

C PHONES jack

Outputs audio to your headphones for private listening.

D SPEAKERS A/B

Turns on or off the speaker set connected to the

SPEAKERS A and/or SPEAKERS B terminals on the rear

panel each time the corresponding button is pressed.

E USB jack

For connecting a USB storage device (p.23) or an iPod

(p.21).

Controls and functions

Front panel

MDFEGH JIKLC

12 3 4 5 6 7 8 9 : A B

Note

Controls and functions

5 En

INTRODUCTION

English

F INPUT selector

Selects the input source you want to listen to.

G BASS control

Increases or decreases the low frequency response. The

center position produces a flat response (p.15).

H TREBLE control

Increases or decreases the high frequency response. The

center position produces a flat response (p.15).

I BALANCE control

Adjusts the sound output balance of the left and right

speakers to compensate for sound imbalances caused by

speaker locations or listening room conditions (p.15).

J LOUDNESS control

Retains a full tonal range at any volume level to

compensate for the human ears’ loss of sensitivity to high

and low-frequency ranges at a low volume level (p.15).

K SELECT/ENTER (jog dial)

Turn the dial to select a numeric value or setting, and press

the dial to confirm.

L RETURN

Returns to the previous indication of the front display.

M VOLUME control

Increases or decreases the sound output level.

Controls and functions

6 En

1 Information display

Displays the current status (such as input name sound

mode name).

You can switch the information that is displayed when you

press DISPLAY (p.29).

2 STEREO

Lights up when the unit is receiving a stereo FM radio

signal.

3 TUNED

Lights up when the unit is receiving an FM/AM radio

station signal.

4 Speaker indicators

“SP A” lights up when the SPEAKERS A output is

enabled and “SP B” lights up when the SPEAKERS B

output is enabled.

5 SLEEP

Lights up when the sleep timer is on.

6 MUTE

Blinks when audio is muted.

7 Volume indicator

Indicates the current volume.

8 Cursor indicators

Indicate the remote control cursor keys currently

operational.

y

You can change the brightness level of the front display by

pressing DIMMER on the remote control (p.8).

Front display

VOL.

MUTE

STEREO

TUNED

SLEEP

SP A

SP B

1

42 3567

8 8

Controls and functions

7 En

INTRODUCTION

Controls and functions

English

1 PHONO jacks

For connecting to a turntable (p.10).

2 OPTICAL 1-2 jacks

For connecting to audio components equipped with

optical digital output (p.10).

3 ANTENNA terminals

For connecting to FM and AM antennas (p.12).

4 COAXIAL 1-2 jacks

For connecting to audio components equipped with a

coaxial digital output (p.10).

5 SPEAKERS terminals

Used to connect speakers (p.11).

6 NETWORK jack

For connecting to a network (p.13).

7 DC OUT jack

For supplying power to a Yamaha AVaccessory. For

details on connections, refer to the instruction manual of

the AV accessory.

8 Power cable

For connecting to an AC wall outlet (p.13).

9 LINE 1-3 jacks

For connecting to analog audio components (p.10).

0 CD jacks

For connecting to a CD player (p.10).

A SUBWOOFER PRE OUT jack

For connecting to a subwoofer with built-in amplifier

(p.10).

B REMOTE IN/OUT jacks

When you have another Yamaha component supporting

remote connection, as this unit does, an infrared

transmitter is not necessary. You can transmit remote

signals by connecting an infrared receiver and the

REMOTE IN jack of the other component to the

REMOTE IN/OUT jacks of this unit, using cables with

monaural miniplugs.

Up to six Yamaha components (including this unit) can be

connected.

Rear panel

:BA9

123 4 6

5 78

REMOTE

IN OUT

Yamaha component

(up to six components

including this unit)

Infrared receiver

Remote control

Rear panel of R-N500

Controls and functions

8 En

This section describes the function of each key on the

remote control used to control this unit or other

components made by Yamaha or other manufacturers.

1

Infrared signal transmitter

Sends infrared signals.

2 SLEEP

Sets the sleep timer (p.16).

3 SOURCE A

Turns on/off an external device.

4 RECEIVER A

Turns on/off (standby) the unit.

5 DIMMER

Changes the brightness level of the front display.

Choose

brightness from 5 levels by pressing this key repeatedly.

6 ID

Changes the remote control ID (p.34).

7 Input selection keys

Select an input source for playback.

COAX 1-2 COAXIAL 1-2 jacks

OPT 1-2 OPTICAL 1-2 jacks

LINE 1-3 LINE 1-3 jacks

PHONO PHONO jacks

TUNER FM/AM tuner

CD CD jacks

USB USB jack

NET NETWORK jack (press repeatedly to select a

desired network source)

8 Radio keys

Operate the FM/AM radio (p.17).

FM Switches to FM radio.

AM Switches to AM radio.

MEMORY Registers FM/AM radio stations as presets.

PRESET Select a preset station.

TUNING Select the radio frequency.

9 Contents operation keys

SHUFFLE Switches shuffle modes.

REPEAT Switches repeat modes.

HOME Shows top-level menu in the front display.

NOW PLAYING

Shows the playback information in the front display.

0 SETUP

Displays the “SETUP” menu (p.31).

A Menu operation keys

Cursor keys Select a menu or a parameter.

ENTER Confirms a selected item.

RETURN Returns to the previous state.

DISPLAY Switches information shown in the front display.

B External device operation keys

Let you play back and select menus and perform other operations

for external devices (p.37).

C Numeric keys

Let you enter numerical values, such as radio frequencies.

D TV operation keys

Let you select TV input and volume, and perform other TV

operations (p.36).

E CODE SET

Registers remote control codes of external devices on the remote

control (p.36).

F SPEAKERS A/B

Turns on and off the set of speakers connected to the SPEAKERS

A and/or SPEAKERS B terminals on the rear panel of this unit

when the corresponding key is pressed.

G MODE

Switches between “Stereo” and “Mono” for FM radio reception (p.17).

Switches the iPod operation modes (p.22).

H OPTION

Displays the “OPTION” menu (p.30).

I VOLUME keys

Adjust the volume.

J MUTE

Mutes the audio output.

y

To operate external devices with the remote control, register a

remote control code for each device before using (p.36

).

Remote control

SOURCE

ID

RECEIVER

CODE SET

SLEEP

DIMMER

SPEAKERS

A B

TV INPUT

TV VOL TV CH

TV MUTE

TV

COAX1

COAX2

OPT1

OPT2

LINE1 LINE2 LINE3

SHUFFLE

REPEAT

MODE

PHONO

TUNER

CD

FM AM

DISC SKIP

PRESET TUNING

MEMORY

SETUP

OPTION

RETURN

TOP

MENU

1

2 3 4

5

6 7 8

9

0

10

ENT

POP-UP

MENU

MUTE

ENTER

VOLUME

HOME

NOW

PLAYING

USB

NET

DISPLAY

+

1

2

E

F

H

I

J

G

3

4

5

6

7

8

9

:

A

B

C

D

Controls and functions

9 En

INTRODUCTION

English

■ Installing batteries

■ Operation range

The remote controls transmit a directional infrared beam.

Be sure to aim the remote controls directly at the remote

control sensor on the front panel of this unit.

Using the remote controls

AAA, R03, UM-4 batteries

30° 30°

Remote control

Approximately

6 m (20 ft)

Connections

10 En

• Do not connect this unit or other components to the main power until all connections between components are complete.

• All connections must be correct: L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. If the connections are faulty,

no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be

unnatural and lack bass. Refer to the owner’s manual for each of your components.

• Do not let bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or the speakers.

y

• The PHONO jacks are designed for connecting a turntable with an MM cartridge.

• Connect your turntable to the GND terminal to reduce noise in the signal. However, for some turntables, you may hear less noise

without the GND connection.

Connections

Connecting speakers and source components

CAUTION

Connecting recording devices

You can connect audio recording devices to the LINE 2-3 (REC) jacks. This jack output analog audio signals selected as the input.

• Be sure to use the LINE 2-3 (REC) jacks only for connecting recording devices.

• If you select LINE2 as the input source, the audio output of the LINE 2 (REC) jacks will be muted. If you select LINE3 as the

input source, the audio output of the LINE 3 (REC) jacks will be muted.

O C

Turntable

Audio

output

CD player

DVD player, etc.

GND

Speakers A

Subwoofer

Audio output

(digital coaxial)

Audio

input

Audio

output

Audio

output

Speakers B

CD recorder, etc.

Audio output

(digital optical)

CD player, etc.

Notes

PREPARATION

11 En

Connections

PREPARATION

English

■ Setting the speaker impedance

Under its default settings, the unit is configured for 8-ohm

speakers. When connecting 4 to 6-ohm speakers, set the

speaker impedance to “4  MIN”.

1 Before connecting speakers, connect the

power cable to an AC wall outlet.

2 While holding down RETURN on the front

panel, press A (power).

3 Check that “SP IMP.” is displayed on the

front display.

4 Press SELECT/ENTER to select “4  MIN”.

5

Press

A

(power) to set the unit to turn off and

remove the power cable from the AC wall outlet.

You are now ready to connect the speakers.

■ Connecting speaker cables

Speaker cables have two wires. One is for connecting the

negative (-) terminal of the unit and the speaker, and the

other is for the positive (+) terminal. If the wires are

colored to prevent confusion, connect the black wire to the

negative and the other wire to the positive terminal.

a

Remove approximately 10 mm (3/8”) of insulation from the ends of

the speaker cable and twist the bare wires of the cable firmly together.

b Loosen the speaker terminal.

c Insert the bare wires of the cable into the gap on the side (upper

right or bottom left) of the terminal.

d Tighten the terminal.

■ Bi-wire connection

Bi-wire connection separates the woofer from the

combined midrange and tweeter section. A bi-wire

compatible speaker has four binding post terminals. These

two sets of terminals allow the speaker to be split into two

independent sections. With these connections, the mid and

high frequency drivers are connected to one set of terminals

and the low frequency driver to another set of terminals.

Connect the other speaker to the other set of terminals in

the same way.

When making bi-wire connections, remove the shorting bridges

or cables on the speaker.

y

To use the bi-wire connections, press SPEAKERS A and

SPEAKERS B on the front panel or on the remote control so that

both SP A and B light up on the front display.

Connecting the speakers

A (power)

SELECT/ENTER

RETURN

SPIMP.8MIN

10 mm

(3/8")

aa

b

d

c

Note

This unit

Speaker

SPEAKERS A/B

SPEAKERS

A/B

SOURCE

ID

RECEIVER

CODE SET

SLEEP

DIMMER

SPEAKERS

A B

COAX1

COAX2

OPT1

OPT2

12 En

Connections

The antennas for receiving FM and AM broadcasts are included with this unit. In general, these antennas should provide

sufficient signal strength. Connect each antenna correctly to the designated terminals.

If you experience poor reception quality, install an outdoor antenna. Consult the nearest authorized Yamaha dealer or service center

about outdoor antennas.

■ Assembling the supplied AM antenna ■ Connecting the wires of the AM antenna

Connecting the FM and AM antennas

Note

FM antenna

(included)

Outdoor AM antenna

Use 5 to 10 m of vinyl-covered wire

extended outdoors from a window.

Outdoor FM antenna

• The AM antenna should

always be connected, even if

an outdoor AM antenna is

connected to this unit.

• The AM antenna should be

placed away from this unit.

AM antenna

(included)

13 En

Connections

PREPARATION

English

You can enjoy Internet radio or music files stored on media servers, such as PCs and Network Attached Storage (NAS),

on the unit.

Connect the unit to your router with a commercially-available STP network cable (CAT-5 or higher straight cable).

y

• If you are using a router that supports DHCP, you do not need to

configure any network settings for the unit, as the network

parameters (such as the IP address) will be assigned

automatically to it. You only need to configure the network

settings if your router does not support DHCP or if you want to

configure the network parameters manually (p.32).

• You can check whether the network parameters (such as IP

address) are properly assigned to the unit in “Information”

(p.32) in the “SETUP” menu.

• Some security software installed on your PC or the firewall

settings of network devices (such as a router) may block the

access of the unit to the network devices or the Internet. In these

cases, configure the security software or firewall settings

appropriately.

• Each server must be connected to the same subnet as the unit.

• To use the service via the Internet, broadband connection is

strongly recommended.

After all the connections are complete, plug in the power

cable.

Connecting to a network

LAN

WAN

Network Attached Storage

(NAS)

Internet

Modem

Router

Network cable

PC

The unit (rear)

Mobile device

(such as iPhone)

Notes

Connecting power cable

To an AC wall outlet

PLAYBACK

14 En

Extreme caution should be exercised when you play back CDs encoded in DTS.

If you play back a CD encoded in DTS on a CD player that does not support DTS, only noise will be heard, and this noise

may damage your speakers. Check whether your CD player supports CDs encoded in DTS. Also, check the sound output

level of your CD player before you play back a CD encoded in DTS.

1 Press A (power) on the front panel (or

RECEIVER A on the remote control) to turn

on this unit.

2 Rotate the INPUT selector on the front panel

(or press one of the input selection keys on

the remote control) to select the input source

you want to listen to.

3 Press SPEAKERS A and/or SPEAKERS B on

the front panel or on the remote control to

select speakers A and/or speakers B.

When speaker set A or speaker set B are turned on,

SP A or SP B is displayed on the front display

accordingly (p.6).

• When one set of speakers is connected using bi-wire connections,

or when using two sets of speakers simultaneously (A and B),

make sure SP A and SP B are displayed on the front display.

• When listening with headphones, turn off the speakers.

4 Play the source.

5 Rotate the VOLUME control on the front

panel (or press VOLUME +/– on the remote

control) to adjust the sound output level.

y

You can adjust the tonal quality by using the BASS, TREBLE,

BALANCE and LOUDNESS controls or the PURE DIRECT

switch on the front panel.

6 Press A (power) on the front panel again (or

RECEIVER A on the remote control) to finish

using this unit and set it to standby mode.

■ Using the PURE DIRECT switch

Routes input signals from your audio sources so that the

input signals bypass the BASS, TREBLE, BALANCE and

LOUDNESS controls, thus eliminating any alterations to

the audio signals and creating the purest possible sound.

The PURE DIRECT indicator lights up and the front

display turns off after a few seconds.

• The BASS, TREBLE, BALANCE, and LOUDNESS controls

do not function while the PURE DIRECT feature is turned on.

• This setting is retained even if you turn off this unit.

Playback

CAUTION

Playing a source

Notes

A (power)

SPEAKERS A/B INPUT selector VOLUME

RECEIVER A

VOLUME

SPEAKERS

A/B

SETUP

OPTION

RETURN

ENTER

VOLUME

HOME

PLAYING

DISPLAY

SOURCE

ID

RECEIVER

CODE SET

SLEEP

DIMMER

SPEAKERS

A B

COAX1

COAX2

OPT1

OPT2

LINE1 LINE2 LINE3

PHONO

TUNER

CD

FM AM

USB

NET

Input selection

keys

Notes

PURE DIRECT switch

BASIC OPERATION

15 En

Playback

BASIC

OPERATION

English

■ Adjusting the BASS and TREBLE

controls

The BASS and TREBLE controls adjust high and low

frequency response.

The center position produces a flat response.

BASS

When you feel there is not enough bass (low frequency

sound), rotate clockwise to boost. When you feel there is

too much bass, rotate counterclockwise to suppress.

Control range: –10 dB to +10 dB (20 Hz)

TREBLE

When you feel there is not enough treble (high frequency

sound), rotate clockwise to boost. When you feel there is

too much treble, rotate counterclockwise to suppress.

Control range: –10 dB to +10 dB (20 kHz)

■ Adjusting the BALANCE control

The BALANCE control adjusts the sound output balance

of the left and right speakers to compensate for sound

imbalance caused by speaker locations or listening room

conditions.

■ Adjusting the LOUDNESS control

Retain a full tonal range at any volume level, thus

compensating for the human ears’ loss of sensitivity to

high and low-frequency ranges at low volume.

If the PURE DIRECT switch is turned on with the

LOUDNESS control set at a certain level, the input signals

bypass the LOUDNESS control, resulting in a sudden

increase in the sound output level. To prevent your ears or

the speakers from being damaged, be sure to press the

PURE DIRECT switch after lowering the sound output

level or after checking that the LOUDNESS control is

properly set.

1 Set the LOUDNESS control to the FLAT

position.

2 Rotate the VOLUME control on the front

panel (or press VOLUME +/– on the remote

control) to set the sound output level to the

loudest listening level that you would listen

to.

3 Rotate the LOUDNESS control until the

desired volume is obtained.

y

After setting the LOUDNESS control, enjoy listening to music at

your preferred volume level. If the effect of the LOUDNESS

control setting is too strong or weak, readjust the LOUDNESS

control.

BASS

TREBLE

BALANCE

CAUTION

LOUDNESS VOLUME

SETUP

OPTION

RETURN

TOP

MENU

POP-UP

MENU

MUTE

ENTER

VOLUME

HOME

NOW

PLAYING

DISPLAY

VOLUME +/–

16 En

Playback

Use this feature to automatically set this unit to standby

mode after a certain amount of time. The sleep timer is

useful when you are going to sleep while this unit is

playing or recording a source.

The sleep timer can only be set with the remote control.

1 Press SLEEP repeatedly to set the amount of

time before this unit is set to standby mode.

Each time you press SLEEP, the front display

changes as shown below.

The SLEEP indicator blinks while setting the amount

of time for the sleep timer.

If the sleep timer is set, the SLEEP indicator on the

front display lights up.

y

• To disable the sleep timer, select “Sleep Off”.

• The sleep timer setting can also be canceled by pressing

RECEIVER A on the remote control to set this unit to standby

mode.

Using the sleep timer

Note

SOURCE

ID

RECEIVER

CODE SET

SLEEP

DIMMER

SPEAKERS

A B

COAX1

COAX2

OPT1

OPT2

LINE1 LINE2 LINE3

PHONO

TUNER

CD

USB

NET

RECEIVER A

SLEEP

S

LEE

P

SLEEP

VOL.

SW

L

R

SP A

Sleep120min.

LISTENING TO FM/AM RADIO

17 En

BASIC

OPERATION

English

1 Press TUNER to select TUNER as the input

source.

2 Press FM or AM to select the reception band

(FM or AM).

3 Press and hold TUNING H / I for more than

1 second to begin tuning.

Press H to tune in to a higher frequency.

Press I to tune in to a lower frequency.

The frequency of the received station is shown in the

front display.

If a broadcast is being received, “TUNED” indicator

on the front display will be lit. If a stereo broadcast is

being received, the “STEREO” indicator will also lit.

If the tuning search does not stop at the desired

station because the station signals are weak, use the

following keys to set a frequency.

TUNING H / I:

Increase/decrease the frequency.

Numeric keys:

Enter a frequency directly. For example, to select

98.50 MHz, press “9”, “8”, “5” and “0” (or ENT).

• When you press the numeric keys on the remote control during

preset tuning, a preset number is selected. Set the tuning mode

to frequency tuning mode using TUNING H / I before

pressing the numeric keys.

• “Wrong Station!” is displayed on the front display if you enter a

frequency that is out of receivable range. Make sure that the

entered frequency is correct.

y

When the signal reception for an FM radio station is unstable,

switching to monaural may improve it.

■ Improving FM reception

If the signal from the station is weak and the sound quality

is not good, set the FM band reception mode to monaural

mode to improve reception.

1 Press MODE repeatedly to select “Stereo”

(automatic stereo mode) or “Mono”

(monaural mode) when this unit is tuned in to

an FM radio station.

When Mono is selected, FM broadcasts will be heard

in monaural sound.

The STEREO indicator on the front panel lights up while

listening to a station in stereo.

Listening to FM/AM radio

FM/AM tuning

Notes

TUNING H / I

FM

AM

TUNER

MODE

TV INPUT

TV VOL TV CH

TV

1

2 3 4

5

6 7 8

9

0

10

ENT

+

LINE1 LINE2 LINE3

SHUFFLE

REPEAT

MODE

PHONO

TUNER

CD

FM AM

PRESET TUNING

MEMORY

HOME

NOW

PLAYING

USB

NET

Numeric keys

STEREO

TUNED

SW

C

L

SL SR

R

VOL .

SP A

FM98.50MHz

Frequency

Note

18 En

Listening to FM/AM radio

You can use the automatic preset tuning function to

automatically register FM stations as presets. This

function enables this unit to automatically tune in to FM

stations that have a strong signal and store up to 40 of

those stations in order. You can then easily recall any

preset station by selecting its preset number.

• If a station is registered to a preset number that already has a

station registered to it, the previously registered station is

overwritten.

• If the station you want to store is weak in signal strength, try

using the manual preset tuning method.

y

• FM stations registered as presets using the automatic preset

registration feature will be heard in stereo.

• Only Radio Data System broadcasting stations are stored

automatically by the Auto Preset function.

1 Press TUNER to select TUNER as the input

source.

2 Press OPTION on the remote control.

The “OPTION” menu is displayed (p.30).

3 Press B / C to select “Auto Preset”, and then

press ENTER.

This unit starts scanning the FM band about 5

seconds later from the lowest frequency upwards.

To begin scanning immediately, hold down the

ENTER key.

y

• Before scanning begins, you can specify the first preset number

to be used by pressing PRESET F/G or cursor key (B/C) on

the remote control.

• To cancel scanning, press FM, AM or RETURN.

When scanning is complete, “FINISH” is displayed

and then the display returns to original state.

You can manually register up to 40 FM/AM stations

(40 total). You can then easily recall any preset station by

selecting its preset number.

■ Registering a radio station manually

Select a radio station manually and register it to a preset

number.

1 Follow “FM/AM tuning” (p.17) to tune into the

desired radio station.

2 Hold down MEMORY for more than 2

seconds.

The first time that you do register a station, the

selected radio station will be registered to the preset

number “01”. Thereafter, each radio station you

select will be registered to the next empty (unused)

preset number after the most recently registered

number.

y

To select a preset number for registering, press MEMORY once

after tuning into the desired radio station, press PRESET F / G

to select a preset number, and then press MEMORY again.

Automatic preset tuning

(FM stations only)

Notes

TUNER

CD

FM AM

PRESET TUNING

MEMORY

USB

NET

SETUP

OPTION

RETURN

TOP

MENU

POP-UP

MENU

MUTE

ENTER

VOLUME

HOME

NOW

PLAYING

DISPLAY

PRESET F / G

RETURN

OPTION

TUNER

ENTER

FM

AM

Cursor keys

B

/

C

VOL.

SP A

AutoPreset

Manual tuning preset

VOL.

SP A

01:FM87.50MHz

Preset number Frequency

COAX1

COAX2

OPT1

OPT2

LINE1 LINE2 LINE3

SHUFFLE

REPEAT

MODE

PHONO

TUNER

CD

FM AM

PRESET TUNING

MEMORY

USB

NET

PRESET F / G

MEMORY

STEREO

TUNED

SW

C

L

SL SR

R

VOL .

01:FM98.50MHz

Preset number

SW

C

L

SL SR

R

STEREO

TUNED

VOL .

02:Empty

“Empty” (not in use) or the frequency currently registered

Pagina se încarcă ...

Yamaha R-N500 Silver Manual de utilizare

Acest manual este potrivit și pentru

Yamaha R-N500 Silver Manual de utilizare

în alte limbi

Lucrări conexe

Alte documente