Parkside PEH 30 A1 ELECTRIC PLANER Operation and Safety Notes

ELECTRIC PLANER PEH 30 A1

ELECTRIC PLANER

Operation and Safety Notes

Translation of original operation manual

ELEkTRohobEL

Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung

ELEkTRIČNA bLANJALICA

Upute za posluživanje i za Vašu sigurnost

Prijevod originalnih uputa za uporabu

ΗΛΕΚΤΡΙΚΗ ΠΛΑΝΗ

Υποδείξεις χειρισμού και ασφαλείας

Μετάφραση των αυθεντικών οδηγιών λειτουργίας

RINDEA ELECTRICĂ

Instrucţiuni de utilizare şi de siguranţă

Traducerea instrucţiunilor de utilizare originale

ЕЛЕКТРИЧЕСКО РЕНДЕ

Инструкции за обслужване и безопасност

Превод на оригиналното ръководство за експлоатация

ELECTRIC PLANER PEH 30 A1

Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the

device.

Rasklopite prije čitanja obije stranice sa slikama i nakon toga se upoznajte sa svim funkcijama uređaja.

Înainte de a citi instrucţiunile, priviţi ambele pagini cu imagini şi familiarizaţi-vă cu toate funcţiile aparatului.

Преди да прочетете отворете двете страници с фигурите и след това се запознайте с всички

функции на уреда.

Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τις δυο σελίδες με τις εικόνες και εξοικειωθείτε με όλες τις

λειτουργίες της συσκευής.

Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie sich anschließend

mit allen Funktionen des Gerätes vertraut.

GB Operation and Safety Notes Page 5

HR Upute za posluživanje i za Vašu sigurnost Stranica 15

RO Instrucţiuni de utilizare şi de siguranţă Pagina 25

BG Инструкции за обслужване и безопасност Cтраница 35

GR Υποδείξεις χειρισμού και ασφαλείας Σελίδα 45

DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 55

111 12 313 14 2 3

5

7

89

B

9 16

4

A

15

10

5 5

6

5

C

H

J

6

D

9

26

17

E

9

221817 21

19

I

G

2324 25

F

5423

4 5°

20

5

5 GB

Table of contents

Introduction

Proper use ...................................................................................................................... Page 6

Features and equipment ...............................................................................................Page 6

Included items ...............................................................................................................Page 7

Technical data ...............................................................................................................Page 7

General safety advice for electrical power tools

1. Workplace safety .....................................................................................................Page 7

2.

Electrical safety .........................................................................................................Page 7

3. Personal safety .......................................................................................................... Page 8

4.

Careful handling and use of electrical power tools ...............................................Page 8

Safety advice relating specifically to power planers ..................................................Page 9

Original accessories / attachments ..............................................................................Page 10

Preparing for use

Switching On / Off ........................................................................................................Page 10

Setting the cutting depth ...............................................................................................Page 10

Vacuum extraction of dust / debris (see Fig. A) ..........................................................Page 10

Parking shoe (see Figs. B / C) .......................................................................................Page 10

The planing process ......................................................................................................Page 11

Chamfering edges (see Fig. H) ....................................................................................Page 11

Using the guide fence (see Fig. I) ................................................................................Page 11

Using the rebate depth stop (see Fig. J) ......................................................................Page 11

Removing and installing a planer blade (see Fig. D) .................................................Page 11

Replacing a drive belt (see Figs. F + G) ......................................................................Page 12

Maintenance and cleaning .........................................................................Page 12

Service centre .......................................................................................................Page 12

Warranty ................................................................................................................... Page 12

Disposal ......................................................................................................................Page 13

Declaration of Conformity / Manufacturer..................................Page 13

6 GB

Electric planer PEH 30 A1

Q

Introduction

Please make sure you familiarise your-

self fully with the way the device works

before you use it for the ﬁrst time and

that you understand how to handle electrical power

tools correctly. To help you do this please read the

accompanying operating instructions. Keep these

instructions in a safe place. If you pass the device

on to anyone else, please ensure that you also

pass on all the documentation.

Q

Proper use

The device is suitable for planing wood in the form

of beams or boards or the like if the workpiece is

held securely in a ﬁxed position. The device is also

suitable for chamfering edges and for rebating.

Any other use or modiﬁcation to the device shall be

considered as improper use and could give rise to

considerable risk of accident. The manufacturer will

not accept liability for loss or damage arising from

improper use. Not suitable for commercial use.

Q

Features and equipment

1

Safety lock-out

2

ON / OFF switch

3

Planing debris removal port (right / left selectable)

4

Belt cover

5

Belt cover screws

6

Guide fence

7

Guide fence ﬁxing screws

8

Fixing nut for setting rebate width

9

Sole

10

V-groove

11

Rebate depth stop ﬁxing screw

12

Rebate depth stop

13

Rotary control for setting planing depth

14

Cutting depth scale

15

Reducer piece

16

Parking shoe

17

Blade shaft

18

Cutting element

19

Plane blade ﬁxing screws

20

Plane blade

21

Side blade shaft guard

22

Allen key

23

Drive belt

24

Large belt wheel

25

Small belt wheel

26

Open spanner

Introduction Introduction / General safety advice for electrical power tools

The following pictograms are used in these operating instructions / on the device:

Read instruction manual!

n

0

Design no-load speed

Observe caution and safety notes! Safety class II

Caution – electric shock!

Danger to life!

Wear hearing protection, dust protec-

tion mask, protective glasses and

protective gloves.

Explosive material!

Keep children away from electrical

power tools!

V

~

Volt (AC)

Check that the device, mains lead

and plug are in good condition!

W

Watts (Eﬀective power)

Dispose packaging and appliance in

an environmentally-friendly way!

7 GB

Q

Included items

1 Electric planer PEH 30 A1

1 Guide fence

1 Rebate depth stop

1 Allen key

1 Open spanner

1 Reducer piece

1 Operating instructions

Q

Technical data

Rated voltage: 230–240 V∼ 50 Hz

Rated power: 750 W

Design no-load speed: n

0

13000 rpm

Planing depth: 0–3.0 mm

Planing width: 82 mm

Protection class: II /

Noise and vibration data:

Measured values for noise are determined in accor-

dance with EN 60745. The A-weighted noise level

of the electrical power tool are typically:

Sound pressure level: 89 dB(A)

Sound power level: 100 dB(A)

Uncertainty K: 3 dB

Wear ear protection!

Evaluated acceleration, typical:

Hand / arm vibration a

h

= 5.644 m / s

2

Uncertainty K = 1.5 m / s

2

The vibration level given in these

instructions has been measured in accordance with

a standardised measurement procedure speciﬁed

in EN 60745 and can be used to compare devices.

Diﬀerent uses of the device give rise to diﬀerent vibra-

tion levels and in many cases they may exceed the

values given in these instructions. It is easy to under-

estimate the vibration load if the electrical power

tool is used regularly in particular circumstances.

Note: If you wish to make an accurate assessment

of the vibration loads experienced during a particular

period of working, you should also take into account

the intervening periods of time when the device is

switched oﬀ or is running but is not actually in use.

This can result in a much lower vibration load over

the whole of the period of working.

General safety advice for

electrical power tools

Read all the safety advice

and instructions! Failure to observe the safety

advice and instructions may result in electric shock,

ﬁre and / or serious injury.

Keep all the safety advice and instructions

in a safe place for future reference!

The term “electrical tool” used in the safety advice

refers to electrical tools powered by mains electricity

(by means of a mains lead) and electrical tools pow-

er

ed by rechargeable batteries (without a mains lead).

1.

Workplace safety

a) Keep your working area clean and

well lit. Untidy or poorly lit working areas

can lead to accidents.

b)

Do not work with the device

in potentially explosive envi-

ronments in which there are

inflammable liquids, gases or dusts.

Electrical power tools create sparks, which can

ignite dusts or fumes.

c)

Keep children and other

people away while you are

operating the electrical tool.

Distractions can cause you to lose control of

the device.

2.

Electrical safety

a)

The mains plug on the device must match

the mains socket. The plug must not

be modified in any way. Do not use

an adapter plug with devices fitted

with a protective earth. Unmodiﬁed

Introduction Introduction / General safety advice for electrical power tools

8 GB

plugs and matching sockets reduce the risk of

electric shock.

b) Avoid touching earthed surfaces such

as pipes, radiators, ovens and refrig-

erators with any part of your body.

There is an increased risk of electric shock if

your body is earthed.

c) Keep the device away from rain or

moisture. Water entering an electrical device

increases the risk of electric shock.

d)

Do not use the mains lead for

any purpose for which it was

not intended, e.g. to carry the

device, to hang up the device or to pull

the mains plug out of the mains socket.

Keep the mains lead away from heat,

oil, sharp edges or moving parts of

the device. Damaged or tangled mains

leads increase the risk of electric shock.

e) When working outdoors with an

electrical power tool always use ex-

tension cables that are also approved

for use outdoors. The use of an extension

cable suitable for outdoor use reduces the risk

of electric shock.

f) Use a residual current device (RCD)

for protection if operating the electri-

cal power tool in a moist environment

is unavoidable. The use of an RCD reduces

the risk of electric shock.

3. Personal safety

a) Remain alert at all times, watch what

you are doing and always proceed

with caution. Do not use the device if

you are tired or under the influence of

drugs, alcohol or medication. One mo

ment

of carelessness when using the device can lead

to serious injury.

b)

Wear personal protective

equipment and always wear

safety glasses. The wearing of

personal protective equipment such as dust

masks, non-slip safety shoes, safety helmets or

ear protectors, appropriate to the type of elec-

trical power tool used and work undertaken,

reduces the risk of injury.

c) Avoid unintentional operation of the

device. Check that the electrical power

tool is switched off before you connect

it to the mains, pick it up or carry it.

Accidents can happen if you carry the device

with your ﬁnger on the ON / OFF switch or with

the device switched on.

d) Remove any setting tools or spanners

before you switch the device on. A tool

or spanner left attached to a rotating part of a

device can lead to injury.

e) Avoid placing your body in an unnat-

ural position. Keep proper footing

and balance at all times. By doing this

you will be in a better position to control the

device in unforeseen circumstances.

f) Wear suitable clothing. Do not wear

loose clothing or jewellery. Keep your

hair, clothing and gloves clear of mov-

ing parts. Loose clothing, jewellery or long

hair can become trapped in moving parts.

g) If vacuum dust extraction and collection

devices are fitted do not forget to

check

that they are properly connected and

correctly used. The use of these devices

reduces the hazard presented by dust.

4.

Careful handling and use

of electrical power tools

a) Do not overload the device. Always

use an electrical power tool that is

intended for the task you are under-

taking. By using the right electrical power

tool for the job you will work more safely and

achieve a better result.

b) Do not use an electrical power tool if

its switch is defective. An electrical power

tool that can no longer be switched on and oﬀ

is dangerous and must be repaired.

c) Pull the mains plug from the socket

before you make any adjustments to

the device, change accessories or when

the device is put away. This precaution is

General safety advice for electrical power tools General safety advice for electrical power tools

9 GB

intended to prevent you from unintentionally

starting the device.

d) When not in use always ensure that

electrical power tools are kept out of

reach of children. Do not let anyone use

the device if he or she is not familiar

with it or has not read the instructions

and advice. Electrical power tools are dan-

gerous when they are used by inexperienced

people.

e) Look after the device carefully. Check

that moving parts are working prop-

erly and move freely. Check for any

parts that are broken or damaged

enough to detrimentally affect the

functioning of the device. Have dam-

aged parts repaired before you use

the device. Many accidents have their origins

in poorly maintained electrical power tools.

f) Keep cutting tools clean and sharp.

Carefully maintained cutting tools with sharp

cutting edges are less likely to jam and are

easier to control.

g) Use the electrical power tool, accesso-

ries, inserted tools etc. in accordance

with these instructions and advice, and

the stipulations drawn up for this par-

ticular type of device. In doing this, take

into account the working conditions

and the task in hand. The use of electrical

power tools for purposes other than those in-

tended can lead to dangerous situations.

Safety advice relating

speciﬁcally to power

planers

Wait until the blade shaft

17

has com-

pletely stopped moving before you

put the device down. An exposed blade

shaft may catch on the surface and lead to loss

of control or serious injury.

Do not place your fingers in the planer

debris removal port

3

. Danger of injury

from rotating parts.

Always switch on the device before

placing it against the workpiece. Oth-

erwise the device could kick back if the planer

blade gets snagged in the workpiece.

When working always keep the sole

9

flat against the workpiece. Otherwise

you could be injured if the plane tilts.

Never plane over metal objects. Other-

wise the planer blade / blade shaft

17

could

be damaged.

Secure the workpiece. Use clamps or a

vice to grip the workpiece ﬁrmly. This is much

safer than holding it with your hand.

Do not plane materials containing

asbestos. Asbestos is a known carcinogen.

The dust generated while

planing could be hazardous

to health, inflammable or

explosive. Wear a dust mask and use a suit-

able dust / debris vacuum extraction device.

Some dusts are known carcinogens.

When planing wood for long periods

and in particular when working on

materials that give rise to dusts that

are hazardous to health, the planer

must be connected to a suitable exter-

nal dust extraction device.

Do not use the power planer if its

mains lead is damaged. Damaged mains

leads increase the risk of electric shock.

Never support yourself by placing

your hands near or in front of the

device or on the workpiece surface.

If you slip you could be injured.

If a dangerous situation arises, pull

the mains plug immediately out of the

mains socket.

When taking a break from your

work, before carrying out any tasks

on the device itself (e.g. changing the

plane blade) or when you are not us-

ing the device, always pull the mains

plug out of the mains socket.

Always work with the mains lead lead-

ing away from the rear of the device.

Use sharp planer blades only.

Do not soak the materials or the sur-

face you are about to work on with

liquids containing solvents.

Avoid contact with rotating parts.

General safety advice for electrical power tools General safety advice for electrical power tools

10 GB

Never use the device for a purpose

for which it was not intended or with

non-original parts / accessories.

Hold the device securely when work-

ing. Ensure that you are standing in a stable,

well-balanced position.

Always keep the device clean, dry

and free from oil or grease.

Q

O

riginal accessories / attachments

Use only the accessories and attach-

ments detailed in the operating instruc-

tions. The use of attachments or accessories

other than those recommended here could lead

to you suﬀering an injury.

Q

Preparing for use

Q

Switching On / Oﬀ

Switching on:

First press the safety lock-out

1

.

Then press and keep pressed the ON / OFF

switch

2

.

Switching off:

Release the ON / OFF switch

2

.

Note: For safety reasons the ON / OFF switch

2

cannot be locked in the ON position.

Q

Setting the cutting depth

The rotary control

13

can be used to set the cutting

depth in steps from 0–3.0 mm according to the cut-

ting depth scale

14

.

Q

Vacuum extraction of dust /

debris (see Fig. A)

DANGER OF INJURY!

Before you carry out any work on the device always

pull the mains plug out of the mains socket.

Planing debris removal port (right / left

selectable):

Release the planing debris removal port

3

by

turning it against the direction of the arrow (out

of the “Lock” position).

Pull the planing debris removal port

3

out of

the device.

The planing debris removal port

3

can be set

to face left or right in the planer.

Push the planing debris removal port

3

into

the device.

Lock the planing debris removal port

3

by

turning it into the “Lock” position.

External vacuum extraction:

If necessary ﬁt the reducer piece

15

when using

a dust extraction system, e.g. a workshop dust

extraction system.

The vacuum cleaner / dust extraction device used

must be suitable for the material being planed.

Connection:

Place the reducer piece

15

ﬁrmly on to the

planing debris removal port

3

.

Push the hose of a suitable dust extraction device

approved for that purpose (e.g. a workshop

vacuum cleaner) on to the planing debris remov-

al port

3

or the reducer piece

15

.

Removal:

Pull the hose of the dust extraction device oﬀ

the planing debris removal port

3

or oﬀ the

reducer piece

15

.

Pull oﬀ the reducer piece

15

, if ﬁtted.

Q

Parking shoe (see Figs. B / C)

The parking shoe

16

allows you to lay the device

down without the risk of damaging the workpiece.

When planing, the parking shoe

16

swings up and

exposes the rear part of the sole

9

.

General safety advice for electrical power tools / Preparing for use Preparing for use

11 GB

Q

The planing process

CAUTION! DANGER OF KICKBACK!

Always switch on the device before placing it

against the workpiece.

Set the required cutting depth.

Switch on the device.

Always place the front part of the sole

9

down

ﬁrst on to the workpiece.

Guide the device with even forward movement

over the surface being planed.

Move the device forward at a slow rate and

ensure that the contact pressure acts evenly on

the sole

9

. Moving forward at too great a rate

results in a poorer surface quality and can lead

to blocking of the planing debris removal port.

Q

Chamfering edges (see Fig. H)

The V-grooves

10

in the front sole

9

allow the de

vice

to be used for simple chamfering of workpiece edges.

Use the V-groove most appropriate to your

desired chamfer width.

Place the planer with the V-groove

10

on the

work-

piece edge and guide the planer along the edge.

Q

Using the guide fence (see Fig. I)

Attach the guide fence

6

to the device with

the ﬁxing screw

7

.

Release the ﬁxing nut

8

and set the guide at

the desired distance.

Retighten the ﬁxing nut

8

.

Exert some slight sideways pressure when guid-

ing the planer with the guide fence.

Q

Using the rebate depth stop

(see Fig. J)

Attach the rebate depth stop

12

to the device

with the ﬁxing screw

11

.

Set the desired rebate depth with the rebate

depth stop

12

.

Make the required number of passes with the

planer until desired rebate depth is achieved.

Q

Removing and installing a

planer blade

20

(see Fig. D)

DANGER OF INJURY!

Before you carry out any work on the device always

pull the mains plug out of the mains socket.

CAUTION! The sharp cutting edges of the plan-

er blade

20

present an injury hazard! Never

touch the cutting edges of the planer blade

20

.

The planer blade

20

has two cutting edges and it

can be ﬁtted either way around.

Replace the planer blade

20

when both cutting

edges are blunt.

Do not resharpen the planer blades

20

.

Reversing or replacing a planer blade

20

IMPORTANT INFORMATION:

Do not release the two Allen keys. They are used to

adjust the height of the blade shaft.

Adjustment is necessary only if you wish to use a

diﬀerent planer blade type e.g. a proﬁled blade.

Always replace both blades at the same time to

avoid out of balance forces.

NOTE: If you only release one blade ﬁrst then you

can use the factory-ﬁtted second blade for orientation

when you ﬁt the new blade.

1. Release the 3 bolts of the cutting element

18

using the supplied open spanner

26

.

Press the removable side guard

21

into the slot

in the housing.

2. Push the cutting element

18

sideways out from

the blade shaft

17

.

3. Push the planer blade

20

sideways out from

the cutting element

18

.

4. Reassembly is carried out in the reverse order

with a reversed or new planer blade.

5. Planer blades

20

can be obtained from the

service address indicated (see section about

warranty).

General safety advice for electrical power tools / Preparing for use Preparing for use

12 GB

Disposal / Declaration of Conformity / ManufacturerPreparing for use / Maintenance and cleaning / Service centre / Warranty

Q

Replacing a drive belt

(see Figs. F + G)

DANGER OF INJURY!

Before you carry out any work on the device always

pull the mains plug out of the mains socket.

Release the screws

5

and remove the belt

cover

4

.

Remove the worn drive belt

23

.

First place the new drive belt

23

on to the small

belt wheel

25

and then pull the drive belt

23

on to the large belt wheel

24

by rotating it.

Put the belt cover

4

back into position and

fasten it into place with the screws

5

.

Q

Maintenance and cleaning

DANGER OF INJURY!

Before you carry out any work on the device always

pull the mains plug out of the mains socket.

Always keep the device and the ventilation

slots clean. This way you will work more safely

and produce better results.

Clean out the planing debris removal port

3

regularly.

Clean out a blocked planing debris removal

port using suitable means (e.g. piece of wood,

air under pressure, etc.).

Use a dry cloth to clean the housing.

Remove any adhering planing dust with a

narrow paint brush.

In no circumstances use sharp objects, or petrol,

solvents or cleaning agents that might attack

plastic. Do not allow any liquids to enter the

inside of the device.

Q

Service centre

Have your device repaire

d

only by qualified specialist personnel

using original manufacturer parts only.

This will ensure that your device remains safe

to use.

If the plug or mains lead

needs to be replaced, always have

the replacement carried out by the

manufacturer or its service centre. This

will ensure that your device remains safe to use.

Q

Warranty

The warranty for this appliance is for 3 year

s

from the date of purchase. The appliance

has been manufactured with care and me-

ticu

lously examined before delivery. Pleas

e

retain your receipt as proof of purchase. In

t

he event of a warranty claim, please make

contact by telephone with our Service De-

partment. Only in this way can a post-free

despatch for your goods be assured.

The warranty covers only claims for material and

maufacturing defects, but not for transport damage,

for wearing parts or for damage to fragile components,

e.g. buttons or batteries. This product is for private use

only and is not intended for commercial use.

The warranty is void in the case of abusive and

improper handling, use of force and internal tam-

pering not carried out by our authorized service

branch. Your statutory rights are not restricted in

any way by this warranty.

The warranty period will not be extended by repairs

made unter warranty. This applies also to replaced

and repaired parts. Any damage and defects extant

on purchase must be reported immediately after

unpacking the appliance, at the latest, two days after

the purchase date. Repairs made after the expiration

of the warranty period are subject to payment.

GB

Service Great Britain

Tel.: 0871 5000 720

(0,10 GBP/Min.)

e-mail: k[email protected]

IAN 68728

13 GB

Disposal / Declaration of Conformity / ManufacturerPreparing for use / Maintenance and cleaning / Service centre / Warranty

Q

Disposal

The packaging is wholly composed of

environmentally-friendly materials that can

be disposed of at a local recycling centre.

Do not dispose of electrical power

tools with the household rubbish!

In

accordance with European Directive 2002 / 96 / E

C

(covering waste electrical and electronic equipment)

and its transposition into national legislation, worn

out electrical power tools must be collected sepa

rately

and taken for environmentally compatible recycling.

Contact your local refuse disposal authority for

more details of how to dispose of your worn out

electrical devices.

Q

Declaration of Conformity /

Manufacturer

We, Kompernaß GmbH, the person responsible for

documents: Mr Semi Uguzlu, Burgstr. 21, D-44867

Bochum, Germany, hereby declare that this product

complies with the following standards, normative

documents and EU directives:

Machinery Directive

(2006 / 42 / EC)

EU Low Voltage Directive

(2006 / 95 / EC)

Electromagnetic Compatibility

(2004 / 108 / EC)

Applicable harmonized standards

EN 60745-1:2009

EN 60745-2-14:2009

EN 55014-1/A1:2009

EN 55014-2/A2:2008

EN 61000-3-2/A2:2009

EN 61000-3-3:2008

Type / Device description:

Electric planer PEH 30 A1

Date of manufacture (DOM): 11–2011

Serial number: IAN 68728

Bochum, 30.11.2011

Semi Uguzlu

- Quality Manager -

We reserve the right to make technical modiﬁca-

tions in the course of further development.

Sicherheit / Bedienung

14

Popis sadržaja

Sicherheit / Bedienung

15 HR

Uvod

Namjenska uporaba ..................................................................................................Stranica 16

Oprema ......................................................................................................................Stranica 16

Opseg pošiljke ...........................................................................................................Stranica 17

Tehnički podatci .........................................................................................................Stranica 17

Opće sigurnosne upute za električni alat

1. Sigurnost na radnom mjestu ..................................................................................Stranica 17

2.

Električna sigurnost ................................................................................................Stranica 17

3. Sigurnost osoba ..................................................................................................... Stranica 18

4.

Pažljivo postupanje s električnim uređajima i njihovo korištenje ........................Stranica 18

Karakteristične sigurnosne upute za električne blanjalice ....................................... Stranica 19

Originalni pribor / originalni dodatni uređaji ........................................................... Stranica 20

Stavljanje u pogon

Uključivanje/ Isključivanje .........................................................................................Stranica 20

Namještanje dubine strugotine .................................................................................Stranica 20

Usisavanje prašine / strugotina (prikaz A) ...............................................................Stranica 20

Postolje za odlaganje blanjalice (vidite prikaz B / C) .............................................Stranica 20

Blanjanje ..................................................................................................................... Stranica 20

Sječenje rubova (vidite prikaz H) .............................................................................Stranica 21

Uporaba paralelnog udara (vidite prikaz I) ............................................................Stranica 21

Uporaba dubine udara žlijeba (vidite prikaz J).......................................................Stranica 21

Vađenje / ugrađivanje noža blanjalice (vidite prikaz D) ........................................Stranica 21

Zamijena pogonskog remena (vidite prikaz F + G) ................................................Stranica 21

Redovito održavanje i čišćenje ............................................................ Stranica 22

Servis .........................................................................................................................Stranica 22

Jamstveni list.......................................................................................................Stranica 22

Zbrinjavanje ........................................................................................................Stranica 22

Objašnjenje konformnosti / Proizvođač ......................................Stranica 23

Popis sadržaja

16 HR

Uvod

Električna blanjalica PEH 30 A1

Q

Uvod

Prije prvog korištenja upoznajte se sa

svim funkcijama uređaja i informirajte se

o pravilnom rukovanju s električnim

uređajem. K tome pročitajte slijedeće upute za kori-

štenje. Dobro čuvajte ove upute. U slučaju prodaje

uređaja proslijedite sve dokumente na treću osobu.

Q

Namjenska uporaba

Uređaj je namijenjen za blanjanje drvenih materija-

la, kao npr. greda ili dasaka, s tim da je potrebno

čvrsto postaviti izradak . Nadalje, uređaj je namije-

njen za koso rezanje rubova i za izradu ureza.

Svako drugo korištenje ili izmjena na uređaju tretira

se kao nepropisano i krije znatne opasnosti od

nesreća. Za oštećenja nastala zbog nepropisane

upotrebe, proizvođač ne preuzima nikakvu odgovor-

nost. Nije namijenjeno za korištenje u obrtne svrhe.

Q

Oprema

1

uklopni zapor

2

sklopka za UKLJUČIVANJE / ISKLJUČIVANJE

3

izbačaj strugotina (prema izboru desno / lijevo)

4

poklopac remena

5

vijci za poklopac remena

6

paralelni udar

7

vijak za pričvršćivanje paralelnog udara

8

sigurnosna matica za namještanje širine žlijeba

9

dno blanjalice

10

v-utori

11

pričvrsni vijak za dubinu udara žlijeba

12

dubina udara žlijeba

13

zakretni regulator za namještanje dubine

strugotine

14

ljestvica dubine strugotine

15

redukcijski komad

16

postolje za odlaganje blanjalice

17

rotirajući pojas noža

18

zatezni dio

19

pričvrsni vijci za nož blanjalice

20

nož blanjalice

21

bočna zaštita rotirajućeg pojasa noža

22

unutarnji šesterobridni ključ

23

pogonski remen

24

veliki kotač remena

25

mali kotač remena

26

čeljusni ključ

U ovim uputama za uporabu / na uređaju rabi se slijedeće prikaze:

Čitati upute za rukovanje!

n

0

Određivanje broja praznohodne

brzine vrtnje

Obratiti pažnju na upozoravajuće i

sigurnosne upute!

Zaštitna klasa II

Čuvajte se strujnog udara!

Opasnost po život!

Nosite zaštitne naočale, zaštitu za

uši, zaštitnu masku i zaštitne rukavice.

Opasnost od eksplozije!

Držite djecu podalje od

električnog alata!

V

~

V (Naizmjenični napon)

Vodite računa o tome, da se ne ošteti

uređaj, mrežni kabel i utikač!

W

W (Efektivna snaga)

Materijal ambalaže i uređaj zbrinite

na način neškodljiv za okoliš!

17 HR

Q

Opseg pošiljke

1 električna blanjalica PEH 30 A1

1 paralelni udar

1 dubina udara žlijeba

1 unutarnji šesterobridni ključ

1 čeljusni ključ

1 redukcijski komad

1 upute za uporabu

Q

Tehnički podatci

Nazivni napon: 230–240 V∼ 50 Hz

Nazivna snaga: 750 W

Broj okretaja dimenzioniranja

u praznom hodu: n

0

13000 min

-1

Dubina blanjalice: 0–3,0 mm

Širina blanjalice: 82 mm

Klasa zaštite: II /

Informacija o buci i vibraciji:

Mjerna vrijednost za buku utvrđena sukladno

EN 60745. A-ocjenjena razina buke električnog

alata iznosi tipično:

Razina zvučnog tlaka: 89 dB(A)

Razina snage zvuka: 100 dB(A)

Nesigurnost K: 3 dB

Potrebno je nositi štitnike za uši!

Ocjenjeno ubrzavanje, karakteristično:

Vibracija ruke a

h

= 5,644 m / s

2

Nesigurnost K = 1,5 m / s

2

Razina titranja, navedena u

ovim uputama, je istražena i određena sukladno

normiranom postupku mjerenja, koji je naveden u

EN 60745 i koji je prikladan za uspoređivanje stroja.

Razina titranja je promijenljiva, ovisno o korištenju

električnog alata, te može u pojedinim slučajevima

ležati iznad vrijednosti, navedene u ovim uputama.

Razina opterećenja titranja može biti podcjenjena,

ako se električni alat redovito koristi na takav način.

Uputa: Za precizno ocjenjivanje titrajnog otpere-

ćenja tijekom određenog radnog vremena, potrebno

je također uzeti u obzir vremena kad je stroj isključen,

ili je uključen ali se zapravo ne rabi. To može znatno

smanjiti titrajno opterećenje, tijekom cijelog radnog

vremena.

Opće sigurnosne upute

za električni alat

Pročitajte sigurnosne

upute kao i sve ostale upute! U slučaju ne

pridržavanja sigurnosnih uputa kao i ostalih uputa,

prijeti opasnost od strujnog udara, požara i / ili teš-

kih ozljeda.

Sačuvajte sve sigurnosne upute kao i sve

ostale upute za ubuduće!

U sigurnosnim uputa rabljeni izraz “električni alat“

odnosi se na električne uređaje sa mrežnim pogo-

nom (sa mrežnim kabelom) i na električni alat sa

akumula

torskim pogonom (bez mrežnog kabela).

1.

Sigurnost na radnom mjestu

a) Vodite uvijek računa o tome, da Vaše

radno mjesto bude čisto i dobro os-

vjetljeno. Nered i ne osvjetljeno područje

rada, može uzrokovati nezgode.

b)

Ne rabite stroj u području gdje

prijeti opasnost od eksplozije,

gdje se nalaze zapaljive teku-

ćine, plinovi ili prašine. Električni alati proiz-

vode iskre, koje mogu zapaliti prašinu ili pare.

c)

Za

vrijeme uporabe elek

trič-

nog alata, držite djecu i druge

osobe izvan dohvata istoga.

U slučaju nepažnje, možete izgubiti kontrolu

nad strojem.

2.

Električna sigurnost

a) Mrežni utikač uređaja mora odgova-

rati utičnici. Utikač se ni na kakav

način ne smije mijenjati. Ne koristite

adapterske utičnice zajedno s zaštitno

Uvod Uvod / Opće sigurnosne upute za električni alat

18 HR

uzemljenim uređajima. Neizmijenjeni

utikači i odgovarajuće utičnice smanjuju rizik

električnog udara.

b) Izbjegavajte dodir tijela s uzemljenim

površinama kao što su cijevi, radijato-

ri, pećnice i hladnjaci. Postoji povećana

opasnost od električnog udara ukoliko je vaše

tijelo uzemljeno.

c) Uređaj držite podalje od kiše i vlage.

Prodiranje vode u unutrašnjost uređaja pove-

ćava opasnost električnog udara.

d)

Ne koristite kabel u neke

druge svrhe, npr. za nošenje

uređaja, vješanje uređaja ili

za izvlačenje utikača iz utičnice. Kabel

držite podalje od topline, ulja, oštrih

rubova i pokretnih dijelova uređaja.

Oštećeni ili spetljani kabel ili utikač povećava

rizik električnog udara.

e) Kod rada na otvorenome koristite

samo produžni kabel koji je dozvoljen

za korištenje na otvorenome. Upotreba

produžnog kabla namijenjenog za korištenje

na otvorenome smanjuje rizik električnog udara.

f) Ako je korištenje električnog alata u

vlažnim prostorima neizbježno, rabite

zaštitnu strujnu sklopku. Korištenje zaštit-

ne strujne sklopke, smanjuje rizik strujnog udara.

3. Sigurnost osoba

a) Budite uvijek pozorni, vodite računa

o tome što radite i razumno pristupite

radu s električnim alatom. Ne rabite

stroj, ako ste umorni ili pod utjecajem

droga, alkohola ili lijekova. Jedan trenu

tak

nepažnje za vrijeme korištenja stroja, može

uzrokovati teške ozljede.

b)

Nosite osobnu zaštitnu opre-

mu i uvijek zaštitne očale.

Korištenje osobne zaštitne opreme,

kao maske za prašinu, protuklizne zaštitne

cipele, zaštitnu kacigu ili štitnik za uši, ovisno o

vrsti i uporabi električnog alata, smanjuje rizik

od ozljeda.

c) Spriječite slučajno uključenje. Uvjerite

se u to, da je električni alat isključen,

prije uključenja na struju, podizanja

ili nošenja. Ako pri nošenju uređaja držite

prst na sklopki za UKLJUČENJE / ISKLJUČENJE

ili ako je uređaj uključen, prijeti opasnost od

nezgode.

d) Prije uključenja stroja, uklonite alat

za podešavanje ili vijčani ključ. Alat ili

ključ, koji se nalazi u rotirajućem dijelu stroja,

može prouzročiti ozljede.

e) Izbjegavajte nenaravan polažaj tijela.

Vodite računa o tome da sigurno

stojite na tlu i održavate vlastitu rav-

notežu. Na taj način bolje možete kontrolira-

ti uređaj, posebno u neočekivanim situacijama.

f) Nosite prikladnu odjeću. Ne nosite

široku odjeću ili nakit. Držite kosu,

odjeću i rukavice dalje od pomičnih

dijelova. Opuštena odjeća, nakit ili duga kosa

mogu biti zahvaćeni od pomičnih dijelova.

g) Ako se montira uređaje za usisavanje

i prihvaćanje prašine, uvjerite se u

to da su priključeni i da se pravilno

koriste. Uporaba tih uređaja, smanjuje

ugrožavanje od prašine.

4.

Pažljivo postupanje s

električnim uređajima i

njihovo korištenje

a) Nemojte uređaj preopterećivati.

Koristite onaj električni uređaj koji

odgovara za Vaš rad. S odgovarajućim

električnim uređajem bolje i sigurnije ćete radi-

ti u navedenom području rada.

b) Ne koristite električni uređaj s neisprav-

nim prekidačem. Električni uređaj koji se više

ne može uključiti i isključiti opasan je i treba

ga dati popraviti.

c) Izvucite utikač iz utičnice, prije namje-

štanja uređaja, zamjene dijelova

opreme ili odlaganja uređaja. Ova

sigurnosna mjera spriječava slučajno

pokretanje električnog alata. Ova mje-

ra opreza spriječava nenamjerno pokretanje

uređaja.

d) Čuvajte ne korišteni električni uređaj

tako da nije na dohvatu djeci. Ne

Opće sigurnosne upute za električni alat Opće sigurnosne upute za električni alat

19 HR

dopustite da uređaj koriste osobe

koje s njim nisu upoznate ili koje nisu

pročitale upute. Električni alati su opasni

kada ih korite osobe bez iskustva.

e) Pažljivo održavajte uređaj. Kontroli-

rajte da li pokretni dijelovi uređaja

besprijekorno funkcioniraju i da ne

zapinju, da dijelovi nisu slomljeni ili

tako oštećeni da je funkcija uređaja

upitna. Molimo da oštećene dijelove

dadete popraviti prije korištenja ure-

đaja. Brojne nesreće imaju uzrok zbog loše

održavanih električnih alata.

f) Alat za rezanje treba biti oštar i čist.

Brižljivo njegovani alat za rezanje sa oštrim

reznim rubovima, manje zaglavi i jednostavniji

je za rukovanje.

g) Rabite električni alat, opremu i ugrad-

ni alat, itd. sukladno ovim uputama i

na način kako je propisano za ovaj

posebni tip uređaja. Pri tome uzmite

u obzir radne uvjete i rad koji se izvodi.

Uporaba električnog alata za drugu osim

predviđene primjene, može uzrokovati opasne

situacije.

Karakteristične sigurno-

sne upute za električne

blanjalice

Prije odlaganja uređaja, pričekajte

zastoj rotirajućeg pojasa noža

17

.

Nezaštićeni pojas noža može se zakvačiti za

površinu i prouzročiti gubitak kontrole kao i

teške ozljede.

Ne zahvaćajte prstima u izbačaj stru-

gotina

3

. Opasnost od ozljeda na rotirajuć

im

dijelovima.

Vodite uređaj isključivo u uključenom

stanju prema izradku. Inače prijeti opa-

snost od protuudarca, ako se nož blanjalice

zakvači za izradak.

Dno blanjalice

9

treba plosnato prili-

jegati na izradak tijekom rada. Inače

prijeti opasnost od ozljeda ako se blanjalica

zakači.

Ne blanjajte nikad preko metalnih

predmeta. Nož blanjalice / rotirajući pojas

noža

17

bi se inače mogao oštetiti.

Osigurajte izradak. Rabite zatezne napra

ve /

škripac kako bi učvrstili izradak. Izradak je na

taj način bolje učvršćen nego rukom.

Zabranjena je obrada materijala koji

sadrži azbest. Azbest se smatra kancerogenim.

Prašine koje nastaju tijekom

rada, mogu biti štetne za

zdravlje, zapaljive ili eksplo-

zivne. Stoga nosite zaštitnu masku protiv pra-

šine i rabite prikladan usis prašine / strugotina,

jer poneke prašine smatra se kancerogenim.

Tijekom duljeg obrađivanja drva i

posebno materijala od kojih nastaju

prašine škodljive zdravlju, potrebno

je uređaj priključiti na vanjsku napra-

vu za usis prašine.

Ne rabite električnu blanjalicu ako je

oštećen kabel. Oštećeni kablovi povećava-

ju rizik od strujnog udara.

Ne naslanjajte ruke ni u kojem slučaju

pored ili ispred uređaja i površine

koju obrađujete. Inače prijeti opasnost od

iskliznuća što bi moglo prouzročiti ozljede.

U slučaju opasnosti smjesta izvucite

utikač iz utičnice.

U slučaju opasnosti, za vrijeme radnih

stanki, prije izvođenja bilo kakvih ra-

dova na uređaju (npr. zamijena noža

blanjalice), uvijek prethodno izvucite

utikač iz utičnice.

Mrežni kabel treba uvijek biti iza

uređaja.

Rabite isključivo oštre noževe blanjalice

.

Ne natapajte materijale ili površine

koje ćete obrađivati sa tekućinama

koje sadrže otapala.

Izbjegavajte dodir s rotirajućim dijelo-

vima.

Ne rabite uređaj nikad protunamjenski

i isključivo sa originalnim dijelovima /

originalnom opremom.

Pridržavajte uređaj tijekom rada.

Vodite računa da sigurno stojite na tlu.

Uređaj treba uvijek biti čist, suh i oslo-

bođen od ulja ili maziva.

Opće sigurnosne upute za električni alat Opće sigurnosne upute za električni alat

20 HR

Q

Originalni pribor / originalni

dodatni uređaji

Rabite isključivo pribor i dodatne ure-

đaje, koji nisu navedeni u uputama

za uporabu. Korištenje drugih osim ovdje

navedenih dijelova ili drugog pribora može

prouzročiti opasnost od ozljeda.

Q

Stavljanje u pogon

Q

Uključivanje/ Isključivanje

Uključivanje:

Prvo pritisnite uklopni zapor

1

.

Nakon toga pritisnite sklopku za UKLJUČIVANJE/

ISKLJUČIVANJE

2

.

Isključivanje:

Otpustite sklopku za UKLJUČVANJE/ISKLJUČI-

VANJE

2

.

Uputa: Iz sigurnosnih razloga, nije moguće areti-

rati sklopku za UKLJUČIVANJE/ISKLJUČIVANJE

2

.

Q

Namještanje dubine strugotine

Pomoću zakretnog regulatora

13

može se od

0–3,0 mm pomoću ljestvica dubine strugotina

14

stupnasto namjestiti dubinu strugotine.

Q

Usisavanje prašine / strugotina

(prikaz A)

OPASNOST OD

OZLJEDA! Prije izvođenja bilo kakvih radova na

uređaju, uvijek prethodno izvucite utikač iz utičnice.

Izbačaj strugotina (prema izboru desno /

lijevo):

Deblokirajte izbačaj strugotina

3

, tako da ga

vrtite u suprotnom smjeru strijelice (iz pozicije

„LOCK“).

Izvucite izbačaj strugotina

3

iz uređaja.

Izbačaj strugotina

3

može se umetnuti desno

ili lijevo u blanjalicu.

Gurnite izbačaj strugotina

3

u uređaj.

Aretirajte izbačaj strugotina

3

pomoću vrtnje

na poziciju „LOCK“.

Odsis pomoću vanjskih uređaja:

U slučaju korištenja sustava za usis prašine, npr.

radionički usisavač, potrebno je rabiti redukcijski

komad

15

.

Usisavač treba biti prikladan za materijal koji se

obrađuje.

Priključivanje:

Nataknite redukcijski komad

15

čvrsto na izba-

čaj strugotina

3

.

Gurnite cijev dozvoljene usisne naprave, npr.

radioničkog usisavača, na izbačaj strugotine

3

,

ili na redukcijski komad

15

.

Izvlačenje:

Odvucite cijev usisne naprave sa izbačaja stru-

gotine

3

ili sa redukcijskog komada

15

.

Odvucite redukcijski komad

15

.

Q

Postolje za odlaganje blanjalice

(vidite prikaz B / C)

Postolje za odlaganje blanjalice

16

omogućuje

odlaganje uređaja bez opasnosti od oštećenja

izradka. Tijekom radnog postupka zaokrene se

postolje za odlaganje blanjalice

16

prema gore i

oslobodi se stražnji dio dna blanjalice

9

.

Q

Blanjanje

OPREZ! OPASNOST OD PROTUUDARCA

!

Vodite uređaj isključivo u uključenom stanju

prema izradku.

Namjestite željenu dubinu strugotine.

Uključite uređaj.

Postavite uređaj sa prednjim dijelom dna bla-

njalice

9

na izradak.

Vodite uređaj sa ravnomjernim pomakom preko

površine koju obrađujete.

Stavljanje u pogonOpće sigurnosne upute za električni alat / Stavljanje u pogon

Pagina se încarcă ...

Parkside PEH 30 A1 ELECTRIC PLANER Operation and Safety Notes

Parkside PEH 30 A1 ELECTRIC PLANER Operation and Safety Notes

în alte limbi

Lucrări conexe

Alte documente