Parkside PWSA 20-Li C3 Instrucțiuni de utilizare

CORDLESS ANGLE GRINDER PWSA 20-Li C3

IAN 360196_2007

AKKU-WINKELSCHLEIFER

Originalbetriebsanleitung

CORDLESS ANGLE GRINDER

Translation of the original instructions

АКУМУЛАТОРЕН ЪГЛОШЛАЙФ

Превод на оригиналното ръководство за експлоатация

POLIZOR UNGHIULAR

Traducerea instrucţiunilor de utilizare original

ΕΠΑΝΑΦΟΡΤΙΖΟΜΕΝΟΣ

ΓΩΝΙΑΚΟΣ ΤΡΟΧΟΣ

Μετάφραση των αυθεντικών οδηγιών λειτουργίας

AKU KUTNA BRUSILICA

Prijevod originalnih uputa za uporabu

AKU UGAONA BRUSILICA

Prevod originalnog uputstva za upotrebu

GB / CY Translation of the original instructions Page 1

HR Prijevod originalnih uputa za uporabu Stranica 19

RS Prevod originalnog uputstva za upotrebu Strana 37

RO Traducerea instrucţiunilor de utilizare original Pagina 55

BG Превод на оригиналното ръководство за експлоатация Cтраница 73

GR / CY Μετάφραση των αυθεντικών οδηγιών λειτουργίας Σελίδα 95

DE / AT / CH Originalbetriebsanleitung Seite 115

Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the

device.

Rasklopite prije čitanja obije stranice sa slikama i nakon toga se upoznajte sa svim funkcijama uređaja.

Pre čitanja rasklopite obe strane sa slikama te se upoznajte sa svim funkcijama uređaja.

Înainte de a citi instrucţiunile, priviţi ambele pagini cu imagini şi familiarizaţi-vă cu toate funcţiile aparatului.

Преди да прочетете отворете двете страници с фигурите и след това се запознайте с всички

функции на уреда.

Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τις δυο σελίδες με τις εικόνες και εξοικειωθείτε με όλες τις

λειτουργίες της συσκευής.

Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie sich anschließend

mit allen Funktionen des Gerätes vertraut.

B

A

DC

E E

8a X

20V max.

18V

All Parkside tools and the chargers PLG 20 A1/PLG 20 A2/PLG 20 A3/ PLG 20 A4/

PDSLG 20 A1 of the X20V Team series are compatible with the PAP 20 A1/PAP 20 A2/

PAP 20 A3/ PAP 20 B1/ PAP 20 B3 battery pack.

Charging times

Charging currents

2 Ah

Battery pack

PAP 20 A1/B1

3 Ah

Battery pack

PAP 20 A2

4 Ah

Battery pack

PAP 20 A3/B3

max. 2.4 A

Charger PLG 20 A1/A4

60 min

2,4 A

90 min

2,4 A

120 min

2,4 A

max. 3.5 A

Charger PLG 20 A2

45 min

3,5 A

60 min

3,5 A

80 min

3,5 A

max. 4.5 A

Charger PLG 20 A3

35 min

3,8 A

45 min

4,5 A

60 min

4,5 A

max. 4.5 A

Charger PDSLG 20 A1

35 min

3,8 A

45 min

4,5 A

60 min

4,5 A

PWSA 20-Li C3 GB│CY │ 1 ■

Contents

Introduction ............................................................2

Intended use ........................................................................2

Features ...........................................................................2

Package contents ....................................................................3

Technical details .....................................................................3

General power tool safety warnings ....................................... 4

1. Work area safety ..................................................................4

2. Electrical safety ...................................................................4

3. Personal safety ....................................................................4

4. Power tool use and care ............................................................5

5. Use and handling of the cordless electrical power tool .....................................5

Safety instructions for all applications ....................................................6

Kickback and corresponding safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Special safety instructions for grinding and abrasive cutting ...................................8

Additional special safety instructions for abrasive cutting .....................................8

Safety guidelines for battery chargers ....................................................9

Permissible accessories ................................................................9

Storage and handling of the recommended accessory tools ..................................10

Working procedures .................................................................10

Before use ............................................................11

Charging the battery pack (seeﬁg.A) ...................................................11

Attaching/disconnecting the battery pack to/from the appliance ..............................11

Checking the battery charge level ......................................................11

Fitting the protective cover for cutting ....................................................11

Adjusting the blade guard ............................................................12

Fitting the additional handle ...........................................................12

Fitting/changing the roughing/ cutting disc ...............................................12

Operation ............................................................13

Switching on and oﬀ ................................................................13

Adjusting the rotational speed .........................................................13

Maintenance and cleaning ...............................................14

Disposal ..............................................................14

Kompernass Handels GmbH warranty ....................................15

Service ...............................................................16

Importer .............................................................16

Translation of the original Conformity Declaration ...........................17

Ordering a replacement battery ..........................................18

Telephone ordering .................................................................18

PWSA 20-Li C3

■ 2 │ GB│CY

CORDLESS ANGLE GRINDER

PWSA 20-Li C3

Introduction

Congratulations on the purchase of your new

appliance. You have chosen a high-quality product.

The operating instructions are part of this product.

They contain important information about safety,

usage and disposal. Before using the product,

please familiarise yourself with all operating and

safety instructions. Use the product only as

described and for the range of applications speci-

ﬁed. Please also pass these operating instructions

on to any future owner.

Intended use

The appliance is intended for cutting, rough cutting

and brushing metal, concrete or tiles without the

use of water. Any other usage or modiﬁcation of

the appliance is deemed to be improper and carries

a signiﬁcant risk of accidents. The manufacturer

accepts no responsibility for damage(s) resulting

from improper usage. The appliance is not intended

for commercial use.

Explanation of the symbols used

Before using the appliance for the ﬁrst

time, read the original operating

instructions and safety instructions.

The use of damaged cutting or

polishing discs is dangerous and can

lead to serious injuries!

 Diameter of the disc

Cordless angle grinder

Wear protective goggles!

Wear ear muﬀs!

Wear safety shoes!

Wear protective gloves!

Wear a dust mask!

Not approved for wet grinding

Not approved for side grinding

Suitable for grinding metal

Features

ON/OFF switch

Release button for the battery pack

Battery pack*

Battery charge level button

Battery display LED

Adjusting wheel for speed pre-selection

Additional handle

Blade guard

Spindle locking button

Screw thread (3 x) for the additional handle

Mounting ring

Screws

Blade guard ﬁxture

High-speed charger (see ﬁg. A)*

Red charge control LED (see ﬁg. A)

Green charge control LED (see ﬁg. A)

Attachment spindle (see ﬁg. C)

Attachment ﬂange (see ﬁg. C)

Clamping nut (see ﬁg. C)

Two-hole mounting spanner (see ﬁg. D)

Bulges

PWSA 20-Li C3 GB│CY │ 3 ■

Package contents

1 cordless angle grinder

1 additional handle

1 blade guard (pre-assembled)

1 two-hole mounting spanner

1 cutting disc (pre-assembled)

1 set of operating instructions

Technical details

Cordless angle grinder PWSA 20-Li C3

Rated voltage 20 V (DC)

Rated idle speed n 2500–10000 rpm

Disc width Ø 125 mm

Thread size M14

Battery PAP 20 A3*

Type LITHIUM ION

Rated voltage 20 V (DC)

Capacity 4 Ah

Cells 10

High-speed battery charger PLG 20 A3*

INPUT

Rated voltage 230–240 V ~,

50 Hz (AC)

Rated power consumption 120 W

Fuse (internal) 3.15 A T3.15A

OUTPUT

Rated voltage 21.5 V (DC)

Rated current 4.5 A

Charging time approx. 60 min

Protection class II / (double insulation)

* BATTERY AND CHARGER ARE NOT INCLUDED

Noise and vibration data

Noise measurement value determined in accord-

ance with EN 60745. The A-rated noise level of

the power tool is typically:

Noise emission value

Sound pressure level LPA = 83 dB(A)

Uncertainty K = 3 dB

Sound power level LWA = 94 dB(A)

Uncertainty K = 3 dB

Wear ear muﬀs!

Total vibration value

Surface grinding

main handle ah, AG = 2.698 m/s2

Uncertainty K = 1.5 m/s2

Surface grinding

Additional handle ah, AG = 3.284 m/s2

Uncertainty K = 1.5 m/s2

NOTE

► The vibration level speciﬁed in these instruc-

tions has been measured in accordance with

a standardised measuring procedure and can

be used for equipment comparisons. The

speciﬁed vibration emission value can also

be used to make an initial exposure estimate.

WARNING!

► The vibration level varies depending on the

use of the power tool and may be higher

than the value speciﬁed in these instructions

in some cases. Regular use of the power tool

in this way may cause the user to underesti-

mate the vibration. Try to keep the vibration

loads as low as possible. Measures to reduce

the vibration load are, e.g. wearing gloves

and limiting the working time. Wherein all

states of operation must be included (e.g.

times when the power tool is switched oﬀ and

times where the power tool is switched on but

running without load).

PWSA 20-Li C3

■ 4 │ GB│CY

General power tool

safety warnings

WARNING!

► Read all safety warnings and all instructions.

Failure to follow the warnings and instructions

may result in electric shock, ﬁre and/or serious

injury.

Save all warnings and instructions for future

reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-

operated (cordless) power tool.

1. Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of ﬂam-

mable liquids, gases or dust. Power tools create

sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

2. Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools. Unmodiﬁed plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of elec-

tric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d)

Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

e)

When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces

the risk of electric shock.

3. Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the inﬂuence of drugs, alcohol or

medication. A moment of inattention while

operating power tools may result in serious

personal injury.

b)

Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate condi-

tions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools

with your ﬁnger on the switch or energising

power tools that have the switch on invites

accidents.

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool

may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

PWSA 20-Li C3 GB│CY │ 5 ■

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use

of dust collection can reduce dust-related

hazards.

4. Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at

the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and oﬀ. Any power tool that

cannot be controlled with the switch is

dangerous and must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalign-

ment or binding of moving parts, breakage of

parts and any other condition that may aﬀect

the power tool’s operation. If damaged, have

the power tool repaired before use. Many

accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed.

Use of the power tool for operations diﬀerent

from those intended could result in a hazardous

situation.

5. Use and handling of the cordless

electrical power tool

a) Charge a rechargeable battery unit using

only the charger recommended by the manu-

facturer. Chargers are often designed for a

particular type of rechargeable battery unit.

There is the danger of ﬁre if other types of

rechargeable battery units are used.

b) Only the rechargeable battery units supplied

are to be used with an electrical power tool.

The use of other rechargeable batteries may

lead to a risk of injury or ﬁre.

c) When they are not being used, store

rechargeable battery units away from paper-

clips, coins, keys, nails, screws or other small

metal objects that could cause the contacts to

be bridged. Short-circuiting the contacts of a

rechargeable battery unit may result in heat

damage or ﬁre.

d) Fluids may leak out of rechargeable battery

units if they are misused. If this happens,

avoid contact with the ﬂuid. If contact occurs,

ﬂush the aﬀected area with water. Seek addi-

tional medical help if any of the ﬂuid gets into

your eyes. Escaping battery ﬂuid may cause

skin irritation or burns.

CAUTION! RISK OF EXPLOSION!

Never charge non-rechargeable

batteries.

Protect the recharge-

able battery from heat (for example, from

continuous exposure to sunlight), ﬁre, water

and moisture. There is a risk of explosion.

PWSA 20-Li C3

■ 6 │ GB│CY

Safety instructions for all

applications

Special safety instructions for grinding and

abrasive cutting

a) This power tool is to be used as a grinder and

abrasive cutting appliance. Please follow all

safety instructions, instructions, diagrams and

data that you receive with the appliance.

If you do not observe the following instructions,

this can lead to an electrical shock, ﬁre and/or

serious injuries.

b) This power tool is not suitable for sandpaper

sanding, working with a steel brush or

burnishing. Using the power tool for applica-

tions for which it is not designed can lead to

hazards and injuries.

c) Do not use any accessories that have not been

speciﬁcally provided or recommended by the

manufacturer for this power tool. Just because

you can attach the accessories to your power

tool does not guarantee they are safe to use.

d) The maximum speed of the accessory tool

used must be at least as high as the maximum

speed speciﬁed for the power tool. Accessories

that rotate faster than the permissible rate can

break and throw pieces into the air.

e) The external diameter and thickness of the

accessory tool used must comply with the

dimensions of the power tool. Incorrectly

dimensioned accessory tools cannot be suﬃ-

ciently shielded or controlled.

f) Attachment tools with a thread insert must

match the thread of the grinding spindle

exactly. For attachment tools that are

mounted using a ﬂange, the diameter of the

hole on the attachment tool must correspond

to the width of the ﬁtment on the ﬂange.

Accessory tools that cannot be ﬁtted precisely

onto the power tool will rotate unevenly, vibrate

severely and can lead to a loss of control.

g) Never use damaged attachment parts. Check

accessory tools such as grinding discs before

each use for chips or cracks, grinding plates

for cracks, wearing or excessive wear and

tear and wire brushes for loose or broken

wires. If the power tool or the accessory tool

in use is dropped, check to see if it is

damaged or use an undamaged accessory

tool. When you have checked and inserted

the accessory tool, ensure that you and any

other people in the vicinity remain outside of

the level of the rotating accessory tool and

allow the tool to rotate at maximum speed for

one minute. Damaged accessories usually

break during the test period.

h) Wear personal protective equipment.

Depending on the application, ensure that

you use full face protection, eye protection or

goggles. Use a dust mask, hearing protec-

tion, protective gloves or special apron to

protect yourself from grindings and material

particles as required. Protect your eyes from

ﬂying debris that may be created during certain

applications. Dust or ﬁlter masks must be used

to ﬁlter any dust created by the application. If

you are exposed to loud noise for any length

of time, you may suﬀer hearing loss.

i) Ensure that other people remain at a safe

distance from your workspace. Anyone who

enters the workspace must wear personal

protective equipment.

Fragments of the workpiece or broken acces-

sory tools can ﬂy oﬀ and cause injury – even

outside the immediate working area.

j) Hold the power tool only by the insulated

handles when you are carrying out work in

which the accessory tool may come into

contact with concealed power cables. Contact

with a live cable can also make metal parts of

the appliance live and could result in an electric

shock.

k) Keep the power cord away from any rotating

accessories. If you lose control of the appli-

ance, the cord may get caught or cut and your

hand or arm could get caught in the rotating

accessory tool.

PWSA 20-Li C3 GB│CY │ 7 ■

l) Never put the power tool down until the

accessory tool being used has come to a

complete standstill. The rotating accessory tool

can come into contact with the surface and

cause you to lose control of the power tool.

m) Do not leave the power tool running whilst

carrying it. Accidental contact between your

clothing and the rotating accessory tool could

lead to physical injury.

n) Clean the ventilation slits of your power tool

regularly. The engine fan draws dust into the

housing and a strong accumulation of metal

dust can cause electrical hazards.

o) Never use the power tool in the vicinity of

inﬂammable materials. Sparks can ignite these

materials.

p) Do not use any accessory tools which require

liquid coolant. The use of water or other liquid

coolants may lead to electric shock.

Kickback and corresponding safety

instructions

Kickback is a sudden reaction caused when a

rotating accessory tool, e.g. grinding disc, grinding

plate, wire brush, etc., catches or jams. Catching or

jamming leads to an abrupt stop of the rotating

accessory tool. If this happens, an uncontrolled

power tool turns rapidly against the direction of

rotation of the accessory tool caught in the

blockage.

If, for example, a grinding disc catches or jams in a

workpiece, the edge of the grinding disc projecting

into the workpiece can get caught and break oﬀ

the grinding disc or cause a kickback. The grinding

disc can then ﬂy in the direction of the operator or

away from him, depending on the direction of

rotation of the disc at the blockage. This can also

break grinding discs.

A kickback is caused by improper or incorrect use

of the power tool. This can be avoided by taking

proper precautions as described below.

a) Hold the power tool ﬁrmly in both hands and

position your body and arms so they can

absorb the force of a kickback. Always use

the additional handle, if available, so that

you have the maximum possible control over

the kickback force or reaction forces at full

speed. By taking adequate precautions, the

operator can stay in control of the kickback

and reaction torques.

b) Never hold your hand close to a rotating

accessory tool. The accessory tool could hit

your hand in the event of a kickback.

c) Avoid having any part of your body in the

region in which the power tool is likely to

move in event of a kickback. The kickback will

force the power tool in the opposite direction to

the direction of rotation of the grinding disc at

the blockage.

d) Take special care when working near corners,

sharp edges, etc. Avoid allowing the acces-

sory tool to bounce back from the workpiece

or jam. The rotating accessory tool is more

likely to jam in corners or sharp edges or if it

rebounds oﬀ them. This can cause a loss of

control or kickback.

e) Do not use chains or toothed saw blades.

Such accessories often cause a kickback or

loss of control over the power tool.

PWSA 20-Li C3

■ 8 │ GB│CY

Special safety instructions for

grinding and abrasive cutting

a)

Use only the grinding accessories approved for

your power tool and the appropriate blade

guard for these grinding tools. Grinding tools

which are not designed for the power tool

cannot be suﬃciently shielded and are unsafe.

b)

Oﬀset grinding discs must be ﬁtted so that the

grinding surface does not protrude over the

level of the blade guard edge. An improperly

ﬁtted grinding disc which protrudes over the

level of the blade guard edge cannot be prop-

erly guarded.

c) The blade guard must be securely mounted

on the power tool and adjusted to ensure

maximum safety so that the smallest possible

amount of the grinding tool is exposed to the

operator. The blade guard is designed to

protect the operator from fragments, accidental

contact with the grinding tool and sparks that

could ignite clothing.

d) Grinding tools should only be used for the

recommended applications. For example:

Never grind with the side surface of a cutting

disc. Cutting discs are designed to remove

material with the edge of the disc. Any lateral

application of force on these grinding tools can

lead to breakage.

e) Always use an undamaged clamping ﬂange

of the correct size and shape for the selected

grinding disc. Suitable ﬂanges support the

grinding disc and reduce the risk of disc

breakage. Flanges for cutting discs can be

diﬀerent to ﬂanges for other grinding discs.

f) Do not use worn grinding discs from larger

power tools. Grinding discs for larger power

tools are not designed for the higher rotational

speeds of smaller power tools and can break.

Additional special safety instructions

for abrasive cutting

a) Avoid any blockage to the cutting disc or

high contact pressure. Do not make any

excessively deep cuts. Overloading the cutting

disc increases the stress and likelihood of tilting

or jamming and thus the possibility of kickback

or breakage of the grinding tool.

b) Avoid the area in front of and behind the

rotating cutting disc. When you move the cutting

disc away from yourself in the workpiece, it is

possible, in the event of a kickback, that the

power tool along with the rotating disc might be

thrown out directly towards you.

b) If the cutting disc jams or you stop working,

switch the tool oﬀ and hold it steadily in the

workpiece until the disc has completely

stopped turning. Never attempt to pull a

rotating cutting disc out of a cut. This could

lead to kickback. Identify and remove the

cause of the jam.

d) Do not switch the power tool back on while it

is located in the workpiece. Allow the cutting

disc to reach its full speed before you care-

fully continue the cut. Otherwise, the disc can

jam, jump out of the workpiece or cause kick-

back.

e) Support boards or large workpieces to reduce

the risk of the cutting disc jamming and

causing a kickback. Large workpieces can bend

under their own weight. The workpiece must be

supported on both sides of the disc: both in the

vicinity of the cutting disc and also at the edge.

f)

Be particularly careful when making pocket

cuts into existing walls or other obscured

areas. The inserted cutting disc may cut into gas

or water pipes, electrical wiring or other objects

that can cause kickback.

PWSA 20-Li C3 GB│CY │ 9 ■

Safety guidelines for battery

chargers

■ This appliance may be used by

children aged 8 years and above

and by persons with limited phys-

ical, sensory or mental capabilities

or lack of experience and knowl-

edge, provided that they are under

supervision or have been told how

to use the appliance safely and are

aware of the potential risks. Do not

allow children to use the appliance

as a toy. Cleaning and user mainte-

nance tasks may not be carried out

by children unless they are super-

vised.

■ To avoid potential risks, damaged

mains cables should be replaced

by the manufacturer, their customer

service department or a similarly

qualiﬁed person.

The charger is suitable

for indoor use only.

WARNING!

■ To avoid potential risks, damaged mains

cables should be replaced by the manufac-

turer, their customer service department or a

similarly qualiﬁed person.

ATTENTION!

♦ This charger can only charge the following

batteries: PAP 20 A1/PAP 20 A2/PAP 20 A3

.

♦ A current list of battery compatibility can be

found at www.lidl.de/Akku.

Permissible accessories

Max. diameter Ø (mm)

Max. thickness (mm)

Thread size (mm)

Max speed (rpm)

Max. circumferential

speed (m/s)

Tool

Blade guard

Cutting disc 125 3 M14 12250 80 Two-hole mounting

spanner Yes

Roughing disc 125 6 M14 12250 80 Two-hole mounting

spanner Yes

PWSA 20-Li C3

■ 10 │ GB│CY

Storage and handling of the

recommended accessory tools

■ Grinding tools must be treated with care and

transported carefully.

■ Grinding tools should be stored in such a

way that they are not exposed to mechanical

damage or environmental inﬂuences (e.g.

damp).

Working procedures

NOTE

► Grinding tools should only be used for the

recommended applications. Otherwise, they

can break, be damaged or cause injuries.

Rough grinding

Never use cutting discs

for rough grinding!

■Move the angle grinder with moderate

pressure back and forth over the workpiece.

■For soft material, move the roughing disc

at a ﬂat angle over the workpiece; for hard

material at a slightly steeper angle.

Abrasive cutting

Never use roughing discs

for cutting!

■Use only tested ﬁbre-reinforced cutting or

grinding discs that are approved for a

peripheral speed of not less than 80 m/s.

CAUTION!

► The grinder continues running after being

turned oﬀ. Do not try to brake it by applying

lateral counterpressure.

■Secure the workpiece. Use clamps/a vice to

hold the workpiece ﬁrmly in place. This is much

safer than simply holding it in your hand.

■Always switch oﬀ the appliance before

putting it down and wait for the appliance to

come to a complete standstill.

■Use the appliance only for dry cutting or

sanding.

■The additional handle must be mounted

on the appliance for all work.

■Materials containing asbestos may not be

processed. Asbestos is a known carcinogen.

Tip! This symbol indicates

proper behaviour.

DANGER! ALWAYS GUIDE THE

APPLIANCE THROUGH THE WORK-

PIECE IN REVERSE ROTATION.

► In the opposite direction there is a risk of

a kickback. The appliance can be pushed

out of the cut.

■Always switch the appliance on before

applying it to the workpiece. After completing

the task, lift the appliance from the workpiece

and then switch it oﬀ.

■Always hold the appliance ﬁrmly with two

hands while working. Ensure that your stance

is secure and stable.

■ For an optimum grinding eﬀect, move the appli-

ance evenly at an angle of 15° to 30°

(between the grinding disc and workpiece)

backwards and forwards.

■When working on angled surfaces, do not

exert great force on the workpiece. If the

rotational speed drops signiﬁcantly, you must

reduce the pressure exerted to allow safe and

eﬀective working. If the appliance suddenly

brakes completely or jams, it must be switched

oﬀ immediately.

■Cutting: Work at a moderate feed rate and

do not tilt the cutting disc.

■Roughing and cutting discs become very hot

– let them cool down completely before

touching them.

■Never use the appliance for purposes other

than the ones for which it was designed.

■Always make sure that the appliance is

turned oﬀ before inserting the battery into it.

■In the event of danger, turn oﬀ the appliance

and remove the battery. Ensure that the appli-

ance is easily and quickly accessible in the

event of an emergency.

PWSA 20-Li C3 GB│CY │ 11 ■

■Always remove the battery during work

breaks, when adjusting the appliance and

when it is not in use. The appliance must be

kept clean, dry and free of oil and grease at

all times.

■Remain alert at all times! Always pay atten-

tion to what you are doing and act with

common sense. Do not use the appliance if

you are distracted or feeling unwell.

WARNING!

Always wear safety goggles.

WARNING!

Always wear a dust mask!

Before use

Charging the battery pack

(seeﬁg.A)

CAUTION!

► Always unplug the appliance before you

remove the battery pack from or connect

the battery pack to the charger.

NOTE

► Never charge the battery pack if the ambient

temperature is below 10°C or above 40°C.

If a lithium-ion battery is to be stored for an

extended period, the charge level should

be checked regularly. The optimum charge

level is between 50% and 80%. The storage

climate should be cool and dry and the

ambient temperature should be between 0°C

and 50°C.

♦ Connect the battery pack to the high-speed

charger (see ﬁg. A).

♦ Insert the power plug into the socket. The

control LED lights up red.

♦ The green LED indicates that the charging

process is complete and the battery pack is

ready.

ATTENTION!

♦ If the red control LED ﬂashes, this means

that the battery pack has overheated and

cannot be charged.

♦ If the red and green control LEDs both

ﬂash, this means that the battery pack is

defective.

♦ Switch oﬀ the charger for at least 15 minutes

between successive charging sessions. Also

disconnect the power plug from the mains

power socket.

Attaching/disconnecting the battery

pack to/from the appliance

Attaching the battery pack

♦ Allow the battery pack to click into the

handle.

Removing the battery pack

♦ Press the release button and remove the

battery pack .

Checking the battery charge level

♦ Press the battery charge level button to

check the status of the battery (see also main

diagram).

The status/remaining charge will be shown on

the battery display LED as follows:

RED/ORANGE/GREEN = maximum charge

RED/ORANGE = medium charge

RED = low charge – charge the battery

Fitting the protective cover for cutting

When cutting with bonded abrasives, always use

the protective cover 8a for cutting.

♦ Slide the protective cover 8a onto the blade

guard (see ﬁg. E) until the plastic clip “X”

snaps into place at the end.

♦ When removing the protective cover 8a,

press the plastic clip “X” in slightly to release

the protective cover 8a.

PWSA 20-Li C3

■ 12 │ GB│CY

Adjusting the blade guard

WARNING! RISK OF INJURY!

► Always switch the appliance oﬀ and remove

the battery before carrying out any work on

the appliance.

RISK OF INJURY!

► Always use the angle grinder with the blade

guard . The blade guard should be

installed securely. Set it so that the highest

possible degree of safety is achieved, i.e.

the smallest possible part of the grinding

disc is exposed to the operator. The blade

guard is designed to protect the operator

from fragments and accidental contact with

the grinding tool.

RISK OF INJURY!

► Make sure that the blade guard is ﬁtted

at at least the same angle as the additional

handle (see ﬁg. B). Otherwise, you could

injure yourself on the roughing disc or cutting

disc.

♦ Turn the blade guard to the required position

(working position). Make sure that the blade

guard is positioned in such a way that the

blade guard ﬁxture lies over one of the

5 bulges on the blade guard (see Fig. E

(fold-out page).

♦ Ensure that the blade guard ﬁxture is ﬁrmly

seated in the respective bulge .

Fitting the additional handle

CAUTION!

► For safety reasons, this appliance may only

be used with the additional handle .

Failure to do so can lead to serious injury.

The additional handle can be screwed

onto the left, the right or the top, depending

on the job at hand.

Fitting/changing the roughing/

cutting disc

Always wear protective gloves when

changing cutting/rough grinding discs.

Pay attention to the dimensions of the roughing/

cutting disc. The diameter of the hole must ﬁt the

attachment ﬂange without any play. Do not use

a reducer or adapter.

NOTE

► Use only discs which are free of dirt.

■ Use only grinding discs whose permissible

speed rating is at least as high as that on the

type plate on the power tool.

■RISK OF INJURY! Press the spindle locking

button only when the attachment spindle

is at a complete standstill.

♦ Press the spindle locking button to lock the

motor.

♦ Undo the clamping nut using the two-hole

mounting spanner (see ﬁg D).

♦ Place the rough grinding or cutting disc with the

label side towards the appliance on the attach-

ment ﬂange .

♦ Then replace the clamping nut on the attach-

ment spindle with the raised side facing up.

PWSA 20-Li C3 GB│CY │ 13 ■

With thin grinding discs (see ﬁg. 1)

♦ The collar of the clamping nut faces upwards

so that a thin grinding disc can be ﬁtted safely.

12

≤ 3,2 mm

Fig. 1

♦ Press the spindle locking button to lock the

motor.

♦ Tighten the clamping nut using the two-hole

mounting spanner .

With thick grinding discs (see ﬁg. 2)

> 3,2 mm

Fig. 2

The collar of the clamping nut faces downwards

so that the grinding disk can be ﬁtted securely onto

the attachment spindle .

♦ Lock the attachment spindle .

♦ Tighten the clamping nut in a clockwise

direction using the two-hole mounting

spanner .

NOTE

► If the disc does not turn smoothly or vibrates

after the change, the disc must be replaced

immediately.

♦ For safety's sake, run the appliance at maximum

speed for 60 seconds after every disc change.

Be aware of unusual noises and sparks.

♦ Check whether all the fastening elements are

correctly ﬁtted.

♦ Make sure that the arrow showing the direction

of rotation (if any) on the cutting or rough

grinding discs (including diamond cutting discs)

and the direction of rotation of the appliance

(arrow showing the direction of rotation on the

head) match.

Operation

Switching on and oﬀ

Check the attached tool before use to ensure that

all fastening elements are correctly ﬁtted.

NOTE

► Always switch on the angle grinder before

making contact with the material, then apply

it to the workpiece.

Switching on:

♦ First, press the ON/OFF switch to the right

so that you can then press it forwards.

Switching oﬀ:

♦ Let go of the ON/OFF switch .

Switching to continuous operation:

♦ First, press the ON/OFF switch to the right

so that you can then press it forwards. Then

press the ON/OFF switch forwards and

down until it engages.

Switching oﬀ continuous operation

♦ Press the ON/OFF switch to the rear and

downwards and release it.

Adjusting the rotational speed

You can use the adjusting wheel for speed pre-

selection to preselect the rotational speed:

(1 = slower speed, 6 = faster speed).

We recommend you carry out practice tests to

determine the correct speed.

The speed can also be changed during operation.

PWSA 20-Li C3

■ 14 │ GB│CY

Maintenance and cleaning

WARNING! RISK OF INJURY! Always

switch the appliance oﬀ and remove

the battery before carrying out any

work on the appliance.

The battery angle grinder is maintenance-free.

■Do not use any sharp objects for cleaning the

appliance. Never permit liquids to penetrate

inside the appliance. Otherwise the appliance

could be damaged.

■ Clean the appliance regularly, preferably imme-

diately after completion of the work.

■ Clean the housing with a dry cloth – do not use

petrol, solvents or cleaners which can attack the

plastic.

■ A vacuum cleaner is required for thorough

cleaning of the appliance.

■ Ventilation openings must never be obstructed.

■ Remove any sanding dust stuck to the appliance

with a brush.

NOTE

► Replacement parts not listed (such as carbon

brushes, switch) can be ordered via our

service hotline.

WARNING!

► Do not use any accessories not recom-

mended by PARKSIDE. This can lead to

electric shock and ﬁre.

Disposal

The packaging consists of environ-

mentally friendly material. It can be

disposed of in the local recycling

containers.

Do not dispose of power tools in

your normal domestic waste!

European Directive 2012/19/EU

requires that worn-out power tools be

collected separately and recycled in an environ-

mentally compatible manner.

Do not dispose of batteries in

your normal household waste!

Remove the batteries from the appli-

ance before disposal. Defective or

worn-out rechargeable batteries must

be recycled according to Directive 2006/66/EC.

Take the battery pack and/or appliance to a

nearby collection facility.

Please consult your local authorities regarding

suitable disposal of worn out power tools/battery

packs.

Dispose of the packaging in an envi-

ronmentally friendly manner.

Note the labelling on the packaging

and separate the packaging material

components for disposal if necessary. The pack-

aging material is labelled with abbreviations (b)

and numbers (a) with the following meanings:

1–7: plastics, 20–22: paper and cardboard,

80–98: composites

Your local community or municipal

authorities can provide information

on how to dispose of the worn-out

product.

PWSA 20-Li C3 GB│CY │ 15 ■

Kompernass Handels GmbH

warranty

Dear Customer,

This appliance has a 3-year warranty valid from

the date of purchase. If this product has any faults,

you, the buyer, have certain statutory rights. Your

statutory rights are not restricted in any way by the

warranty described below.

Warranty conditions

The warranty period starts on the date of purchase.

Please keep your receipt in a safe place. This will

be required as proof of purchase.

If any material or manufacturing fault occurs within

three years of the date of purchase of the product,

we will either repair or replace the product for you

or refund the purchase price (at our discretion).

This warranty service requires that you present the

defective appliance and the proof of purchase

(receipt) within the three-year warranty period,

along with a brief written description of the fault

and of when it occurred.

If the defect is covered by the warranty, your

product will either be repaired or replaced by us.

The repair or replacement of a product does not

signify the beginning of a new warranty period.

Warranty period and statutory claims for

defects

The warranty period is not prolonged by repairs

eﬀected under the warranty. This also applies to

replaced and repaired components. Any damage

and defects present at the time of purchase must

be reported immediately after unpacking. Repairs

carried out after expiry of the warranty period shall

be subject to a fee.

Scope of the warranty

This appliance has been manufactured in accord-

ance with strict quality guidelines and inspected

meticulously prior to delivery.

The warranty covers material faults or production

faults. The warranty does not extend to product

parts subject to normal wear and tear or to fragile

parts which could be considered as consumable

parts such as switches or parts made of glass.

The warranty does not apply if the product has

been damaged, improperly used or improperly

maintained. The directions in the operating instruc-

tions for the product regarding proper use of the

product are to be strictly followed. Uses and

actions that are discouraged in the operating

instructions or which are warned against must be

avoided.

This product is intended solely for private use and

not for commercial purposes. The warranty shall

be deemed void in cases of misuse or improper

handling, use of force and modiﬁcations / repairs

which have not been carried out by one of our

authorised Service centres.

The warranty period does not apply to

■ Normal reduction of the battery capacity

over time

■ Commercial use of the product

■ Damage to or alteration of the product by the

customer

■ Non-compliance with safety and maintenance

instructions, operating errors

■ Damage caused by natural hazards

Pagina se încarcă ...

Parkside PWSA 20-Li C3 Instrucțiuni de utilizare

Parkside PWSA 20-Li C3 Instrucțiuni de utilizare

Lucrări conexe

Alte documente