Parkside 339124 1910 Translation Of The Original Instructions

CORDLESS HAMMER DRILL PABH 20-Li B2

AKKU-BOHRHAMMER

Originalbetriebsanleitung

IAN 339124_1910

CORDLESS HAMMER DRILL

Translation of the original instructions

АКУМУЛАТОРЕН ПЕРФОРАТОР

Превод на оригиналното ръководство за експлоатация

CIOCAN ROTOPERCUTOR

CU ACUMULATOR

Traducerea instrucţiunilor de utilizare original

ΕΠΑΝΑΦΟΡΤΙΖΟΜΕΝΟ

ΚΡΟΥΣΤΙΚΟ ΔΡΑΠΑΝΟ

Μετάφραση των αυθεντικών οδηγιών λειτουργίας

AKU UDARNA BUŠILICA

Prijevod originalnih uputa za uporabu

AKU UDARNA BUŠILICA

Prevod originalnog uputstva za upotrebu

GB / CY Translation of the original instructions Page 1

HR Prijevod originalnih uputa za uporabu Stranica 15

RS Prevod originalnog uputstva za upotrebu Strana 29

RO Traducerea instrucţiunilor de utilizare original Pagina 43

BG Превод на оригиналното ръководство за експлоатация Cтраница 57

GR / CY Μετάφραση των αυθεντικών οδηγιών λειτουργίας Σελίδα 73

DE / AT / CH Originalbetriebsanleitung Seite 87

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of

the device.

Prije nego što pročitate tekst, otvorite stranicu sa slikama i upoznajte se na osnovu toga sa svim funkcijama

uređaja.

Pre čitanja rasklopite obe strane sa slikama te se upoznajte sa svim funkcijama uređaja.

Înainte de a citi instrucţiunile, priviţi imaginile şi familiarizaţi-vă cu toate funcţiile aparatului.

Преди да прочетете отворете страницата с фигурите и след това се запознайте с всички функции

на уреда.

Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα με τις εικόνες και εξοικειωθείτε με όλες τις λειτουργίες

της συσκευής.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

A

R

20V max.

18V

All Parkside tools and the chargers PLG 20 A1/PLG 20 A2/PLG 20 A3/PDSLG 20 A1 of the

X20V Team series are compatible with the PAP 20 A1/PAP 20 A2/PAP 20 A3 battery pack.

Charging times

Charging currents

2 Ah

Battery pack

PAP 20 A1

3 Ah

Battery pack

PAP 20 A2

4 Ah

Battery pack

PAP 20 A3

max. 2.4 A

Charger PLG 20 A1

60 min

2,4 A

90 min

2,4 A

120 min

2,4 A

max. 3.5 A

Charger PLG 20 A2

60 min

2,4 A

60 min

3,5 A

80 min

3,5 A

max. 4.5 A

Charger PLG 20 A3

45 min

3,5 A

45 min

4,5 A

60 min

4,5 A

max. 4.5 A

Charger PDSLG 20 A1

35 min

3,5 A

45 min

4,5 A

60 min

4,5 A

PABH 20-Li B2

GB

│

CY

│

1 ■

Contents

Introduction .........................................................2

Intended use .................................................................... 2

Depicted components ............................................................. 2

Package contents ................................................................. 2

Technical data ................................................................... 2

General Power Tool Safety Warnings ....................................3

1. Work area safety .............................................................. 3

2. Electrical safety ................................................................ 4

3. Personal safety ................................................................ 4

4. Use and handling of the power tool ................................................ 5

Use and handling of the cordless electrical power tool .................................... 5

5. Service ....................................................................... 5

Safety guidelines for battery chargers ................................................. 6

Safety instructions for hammer drills .................................................. 6

Original accessories/auxiliary equipment .............................................. 6

Before use ...........................................................7

Charging the battery pack (see ﬁg. A) ...................................................7

Checking the battery charge level .................................................... 7

Attaching/disconnecting the battery pack to/from the appliance ........................... 7

Operation ...........................................................7

Selecting a tool .................................................................. 7

Tool-changing ................................................................... 7

Fitting an SDS tool/Keyless chuck .................................................... 8

Removing an SDS tool ............................................................. 8

Operation ...........................................................8

Select operating mode ............................................................ 8

Setting the rotation direction ........................................................ 8

Switching on/oﬀ ................................................................. 9

Set drill/hammer speed ............................................................ 9

Maintenance and cleaning .............................................9

Disposal .............................................................9

Kompernass Handels GmbH warranty ..................................10

Service .............................................................11

Importer ...........................................................11

Translation of the original Conformity Declaration .........................12

Ordering a replacement battery ........................................13

Telephone ordering ..............................................................13

PABH 20-Li B2

■ 2

│

GB

│

CY

CORDLESS HAMMER DRILL

PABH 20-LI B2

Introduction

Congratulations on the purchase of your

new appliance. You have selected a high-

quality product. The operating instructions

are part of this product. They contain important

information about safety, usage and disposal.

Before using the product, please familiarise your-

self with all operating and safety instructions. Use

the product only as described and for the range of

applications speciﬁed. Please also pass these oper-

ating instructions on to any future owner.

Intended use

The cordless hammer drill PABH 20-Li B2

(hereinafter appliance) is suitable for:

▯ Hammer-drilling into brickwork, concrete and

stone

▯ Drilling into stone, wood and metal

▯ Screwing into wood and metal

Any other usage of or modiﬁcation to the appliance

is deemed to be improper and carries a signiﬁcant

risk of accidents.

The manufacturer accepts no responsibility for

damage(s) attributable to misuse.

The appliance is not intended for commercial use.

Depicted components

SDS-plus tool holder

Dust protection cap

Locking collar

“Drill/hammer drill” switch

Rotation direction switch

On/Oﬀ switch

Battery charge level button

Battery display LED

Battery pack*

Release button for the battery pack

LED work light

High-speed charger*

Red charge control LED

Green charge control LED

Drill with hexagonal shank

Drill with SDS-plus ﬁtting

Screwdriver bits

Keyless chuck

Universal bit holder

Grease

Package contents

1 cordless hammer drill PABH 20-Li B2

3 x 150 mm SDS-plus drills Ø 6/8/10 mm

3 x drill bits Ø 5/6/8 mm (HSS) with hexagonal

shanks

6 x 50 mm bits (S2):

5.5/PH1/PZ1/PZ2/PZ2/T20/T25

2 x Bit PH2 (50 mm)

1 x bit extension (hexagonal shank)

1 x 10 mm keyless chuck for round shank drill bits

(SDS-plus ﬁtting)

1 carrying case

50 g grease

1 set of operating instructions

Technical data

Cordless hammer drill PABH 20-Li B2

Nominal voltage 20 V (DC)

Idle speed n

0

0–900 rpm

Stroke rate 0–5000 spm

Stroke energy ≥ 1 joule

Max. drill diameter 8 mm for metal

10 mm for concrete

16 mm for wood

Battery pack PAP 20 A1*

Type LITHIUM ION

Rated voltage 20 V

(DC)

Capacity 2 Ah

Cells 5

High-speed charger PLG 20 A1*

INPUT

Rated voltage 230–240 V ∼, 50 Hz

(AC)

Rated power consumption 65 W

Fuse (internal) 3.15 A

T3.15A

PABH 20-Li B2

GB

│

CY

│

3 ■

OUTPUT

Rated voltage 21.5 V

(DC)

Rated current 2.4 A

Charging time approx. 60 min

Protection class II /

(double insulation)

* BATTERY AND CHARGER ARE NOT INCLUDED

Noise emission value

Noise measurement value determined in accord-

ance with EN 60745. The A-rated noise level of

the power tool is typically:

Hammer drilling

Sound pressure level L

pA

= 86.5 dB(A)

Uncertainty K

pA

= 3 dB(A)

Sound power level L

WA

= 97.5 dB(A)

Uncertainty K

WA

= 3 dB(A)

Wear hearing protection!

Total vibration value

Total vibration values (vector total of three directions)

determined in accordance with EN 60745:

Hammer drilling in concrete a

h(HD)

= 4.724 m/s

2

K = 1.5 m/s

2

WARNING!

► The vibration level varies in accordance with

the use of the power tool and may be higher

than the value speciﬁed in these instructions

in some cases. Regular use of the electric tool

in such a way may cause the user to underes-

timate the vibration. Try to keep the vibration

loads as low as possible. Measures to reduce

the vibration load are, e.g. wearing gloves

and limiting the working time. All states of

operation must be taken into account (e.g.

times when the power tool is switched oﬀ and

times where the power tool is switched on but

running without load).

NOTE

► The vibration level speciﬁed in these instruc-

tions has been measured in accordance

with the standardised measuring procedure

speciﬁed in EN 60745 and can be used to

make equipment comparisons. The speciﬁed

vibration emission value can also be used to

make an initial exposure estimate.

General Power Tool

Safety Warnings

WARNING!

► Read all safety warnings and all

instructions. Failure to follow the

warnings and instructions may

result in electric shock, ﬁre and/or

serious injury.

Save all warnings and instructions for future

reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-

operated (cordless) power tool.

1. Work area safety

a) Keep work area clean and well lit. Cluttered

or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of ﬂam-

mable liquids, gases or dust. Power tools create

sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

PABH 20-Li B2

■ 4

│

GB

│

CY

2. Electrical safety

a) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiﬁed plugs and matching outlets

will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of elec-

tric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces

the risk of electric shock.

3. Personal safety

a) Stay alert, watch what you are doing and

use common sense when operating a power

tool. Do not use a power tool while you are

tired or under the inﬂuence of drugs, alcohol

or medication. A moment of inattention while

operating power tools may result in serious

personal injury.

b) Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat,

or hearing protection used for appropriate

conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools

with your ﬁnger on the switch or energising

power tools that have the switch on invites acci-

dents.

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool

may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use

of dust collection can reduce dust-related haz-

ards.

PABH 20-Li B2

GB

│

CY

│

5 ■

4. Use and handling of the power

tool

a) Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at

the rate for which it was designed.

b) Do not use the power tool if the switch does not

turn it on and oﬀ. Any power tool that cannot

be controlled with the switch is dangerous and

must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of

children. Do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools diligently. Check for

misalignment or binding of moving parts,

breakage of parts and any other condition

that may aﬀect the power tool’s operation.

If damaged, have the power tool repaired

before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits,

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed. Use of the

power tool for operations diﬀerent from those

intended could result in a hazardous situation.

Use and handling of the cordless

electrical power tool

a) Charge a rechargeable battery unit using only

the charger recommended by the manufactur-

er. Chargers are often designed for a particular

type of rechargeable battery unit. There is the

danger of ﬁre if other types of rechargeable

battery units are used.

b) Only the rechargeable battery units supplied

are to be used with an electrical power tool.

The use of other rechargeable battery units may

lead to the danger of injury or ﬁre.

c) When they are not being used, store re-

chargeable battery units away from paper-

clips, coins, keys, nails, screws or other small

metal objects that could cause the contacts

to be bridged. Short-circuiting the contacts of

a rechargeable battery unit may result in heat

damage or ﬁre.

d) Fluids may leak out of rechargeable battery

units if they are misused. If this happens,

avoid contact with the ﬂuid. If contact occurs,

ﬂush the aﬀected area with water. Seek addi-

tional medical help if any of the ﬂuid gets into

your eyes. Escaping battery ﬂuid may cause

skin irritation or burns.

CAUTION! RISK OF EXPLOSION!

Never charge non-rechargeable

batteries!

Protect the rechargeable battery

from heat, for example from

continuous exposure to sunlight,

ﬁre, water and moisture.

There is a risk of explosion.

5. Service

a) Have your power tool serviced by a qualiﬁed

repair person using only identical replace-

ment parts. This will ensure that the safety of

the power tool is maintained.

PABH 20-Li B2

■ 6

│

GB

│

CY

Safety guidelines for battery

chargers

■ This appliance may be used by

children aged 8 years and above

and by persons with limited physical,

sensory or mental capabilities or

lack of experience and know ledge,

provided that they are under super-

vision or have been told how to use

the appliance safely and are aware

of the potential risks. Children must

not play with the appliance. Clean-

ing and user maintenance tasks

may not be carried out by children

unless they are supervised.

■ To avoid potential risks, damaged

mains cables should be replaced

by the manufacturer, their customer

service department or a similarly

qualiﬁed person.

The charger is suitable for

indoor use only.

ATTENTION!

♦ This charger can only charge the following

batteries: PAP 20 A1/PAP 20 A2/PAP 20 A3

.

♦ A current list of battery compatibility can be

found at www.lidl.de/Akku.

Safety instructions for hammer drills

■ Wear hearing protection. Exposure

to loud noise can lead to hearing loss.

■ Use the additional handles supplied with the

appliance. Loss of control can lead to injuries.

■ Hold the appliance using the insulated handle

areas if you are carry out any work during

which the attached tool could contact hidden

power cables. Contact with a live wire may

electrify exposed metal parts of the power tool

and could give the operator an electric shock.

■

Wear a dust mask.

WARNING! TOXIC DUST!

► Working with the tool can produce harmful/

toxic dusts which represent a health hazard

for the person operating the appliance and

for anyone else in the vicinity.

■ CAUTION, POWER CABLES! DANGER!

Ensure that you are not likely to hit power, gas

or water supply lines when you are working

with the power tool. If necessary, check with a

service line detector before you start to cut or

drill into a surface.

Original accessories/auxiliary

equipment

■ Only use the accessories and additional

equipment that are speciﬁed in the operating

instructions and compatible with the appli-

ance.

WARNING!

■ Do not use any accessories which are not

recommended by PARKSIDE. This can lead to

an electric shock and ﬁre.

PABH 20-Li B2

GB

│

CY

│

7 ■

Before use

Charging the battery pack (see ﬁg. A)

CAUTION!

► Always pull out the plug before you remove

the battery pack

from or connect the

battery pack to the charger.

► Never charge the battery pack

when

the ambient temperature is below 10°C or

above 40°C.

♦ Connect the battery pack

to the high-speed

battery charger (see Fig. A).

♦ Insert the power plug into the socket. The con-

trol LED

lights up red.

♦ The green LED

indicates that the charging

process is complete and the battery pack is

ready.

♦ Switch oﬀ the charger for at least 15 minutes

between successive charging sessions. Also

disconnect the power plug from the mains

power socket.

Checking the battery charge level

♦ Press the battery charge level button to

check the status of the battery (see also main

diagram). The status/remaining charge will be

shown on the battery display LED as follows:

RED/ORANGE/GREEN = maximum charge

RED/ORANGE = medium charge

RED = low charge – charge the battery

Attaching/disconnecting the battery

pack to/from the appliance

Inserting the battery pack

♦ Push the rotation direction switch

into the

middle position (lock). Allow the battery pack

to click into the handle.

Removing the battery pack

♦ Press the release button

and remove the

battery pack

.

Operation

NOTE

► Push the rotation direction switch

into

the middle position before carrying out

any work on the power tool (e.g. mainten-

ance, tool-changing, etc.) as well as during

carriage and storage of the power tool.

Unintentional activation of the On/Oﬀ

switch

can result in injury.

Selecting a tool

■ For hammer drilling, you will need an SDS-plus

drilling tool.

■ For standard drilling in wood, metal, ceramics

and plastic, you can use an appropriate SDS-

plus drilling tool or a tool with a hexagonal

shank.

■ For screwing, use the screwdriver bits

that

you can attach using the SDS bit adapter .

Tool-changing

■ You can use the SDS-plus tool holder to

change tools quickly and easily without the

need for any additional tools.

■ The SDS-plus drilling tool moves freely (depend-

ing on the system). This leads to a radial run-out

deviation while idling. This has no eﬀect on the

accuracy of the drill hole as the drill centres

itself during drilling.

■ The dust protection cap

largely prevents the

entry of drilling dust into tool holder during

operation. Ensure that the dust protection cap

does not get damaged when ﬁtting tools.

NOTE

► A damaged dust protection cap

must

be replaced immediately. We recommend

having this done by a customer service

workshop.

PABH 20-Li B2

■ 8

│

GB

│

CY

Fitting an SDS tool/Keyless chuck

WARNING!

►

Do not use the quick-action drill

chuck

in hammer drilling or chiselling

operation!

♦ Grease the tool holder

slightly before

inserting the tool.

♦ Insert the tool rotatingly into the tool holder

until it clicks into place.

♦ Check that the tool is properly locked by pulling

it. The system has radial play because of the

design.

Removing an SDS tool

♦ Pull the locking sleeve backwards and

remove the tool.

Operation

Select operating mode

■ Use the “Drill/hammer drill” switch to select

the operating mode of the power tool.

NOTE

► Change the mode only when power tool is

switched oﬀ. Otherwise, the tool could be

damaged.

♦ To change the operating mode, turn the “Drill/

hammer drill” switch

to the desired position.

Hammer drilling = Hammer ON

Drilling/screwing = Hammer OFF

Setting the rotation direction

NOTE

► Operate the rotation direction switch

only

when the appliance is at a standstill.

■ You can use the rotation direction switch

to

change the direction of rotation of the power

tool. This is not possible, however, while the on/

oﬀ switch is pressed in.

Clockwise

♦ For drilling and screwing in screws, turn the

rotation direction switch

to the left as far

as the stop.

♦ Anti-clockwise

♦ For undoing and removing screws and nuts, turn

the rotation direction switch

to the right as

far as the stop.

PABH 20-Li B2

GB

│

CY

│

9 ■

Switching on/oﬀ

Switching on

♦ To start the power tool, press the on/oﬀ switch

and keep it pressed in.

■ The lamp

lights up when the on/oﬀ switch

is pushed in slightly or fully and illuminates the

working area in low light conditions.

Switching oﬀ

♦ To switch oﬀ the power tool, let go of the on/

oﬀ switch

.

■ At low temperatures, the power tool will only

reach its full hammer performance/strike power

after a certain time.

■ To save energy, do not switch the power tool

on unless you plan to use it.

Set drill/hammer speed

■ You can inﬁnitely adjust the drill/hammer speed

of the switched on power tool, depending on

how far the on/oﬀ switch is pressed in.

Pressing the on/oﬀ switch lightly yields a

low drill/hammer speed. Increasing pressure

increases the speed.

Run-on brake

■ When you release the on/oﬀ switch

, the

brake stops the chuck and prevents run-on of

the tool.

Maintenance and cleaning

WARNING! RISK OF INJURY! Always

switch the appliance oﬀ and remove

the battery before carrying out any

work on the appliance.

■ The cordless hammer drill is maintenance-free.

■ Use a soft, dry cloth to clean the housing.

■ If a lithium-ion battery is to be stored for an

extended period, the charge level should be

checked regularly. The optimum charge level is

between 50% and 80%. The optimum storage

environment is cool and dry.

NOTE

► Replacement parts not listed (such as carbon

brushes, switch) can be ordered via our

service hotline.

Disposal

The packaging protects the device

from damage during transport. The

packaging materials have been selected

for their environmental friendliness and

disposal attributes, and are therefore

recyclable.

Returning the packaging into the material cycle

conserves raw materials and reduces the amount of

waste generated. Dispose of packaging materials

that are no longer needed in accordance with

applicable local regulations.

NOTE

► If possible, keep the original packaging of the

device for the entire duration of the warranty

period so that the device can be packed

properly for return shipment in the event of a

warranty claim.

PABH 20-Li B2

■ 10

│

GB

│

CY

Do not dispose of power tools

in your normal domestic waste!

European Directive 2012/19/EU

requires that worn-out power tools be

collected separately and recycled in an environ-

mentally compatible manner.

WARNING!

■ Remove the battery before disposal.

Do not dispose of batteries in

your normal household waste!

Defective or worn-out rechargeable

batteries must be recycled according

to Directive 2006/66/EC. Take the battery pack

and/or appliance to a nearby collection facility.

Please consult your local authorities regarding

suitable disposal of worn out power tools/battery

packs.

Dispose of the packaging in an

environmentally friendly manner.

Note the labelling on the packaging

and separate the packaging material

components for disposal if necessary. The packag-

ing material is labelled with abbreviations (a) and

numbers (b) with the following meanings:

1–7: plastics, 20–22: paper and cardboard,

80–98: composites.

Your local community or municipal

authorities can provide information

on how to dispose of the worn-out

product.

Kompernass Handels GmbH

warranty

Dear Customer,

This appliance has a 3-year warranty valid from

the date of purchase. If this product has any faults,

you, the buyer, have certain statutory rights. Your

statutory rights are not restricted in any way by the

warranty described below.

Warranty conditions

The warranty period starts on the date of purchase.

Please keep your receipt in a safe place. This will

be required as proof of purchase.

If any material or manufacturing fault occurs within

three years of the date of purchase of the product,

we will either repair or replace the product for you

or refund the purchase price (at our discretion).

This warranty service requires that you present the

defective appliance and the proof of purchase

(receipt) within the three-year warranty period,

along with a brief written description of the fault

and of when it occurred.

If the defect is covered by the warranty, your

product will either be repaired or replaced by us.

The repair or replacement of a product does not

signify the beginning of a new warranty period.

Warranty period and statutory claims for

defects

The warranty period is not prolonged by repairs

eﬀected under the warranty. This also applies to

replaced and repaired components. Any damage

and defects present at the time of purchase must

be reported immediately after unpacking. Repairs

carried out after expiry of the warranty period shall

be subject to a fee.

Scope of the warranty

This appliance has been manufactured in accord-

ance with strict quality guidelines and inspected

meticulously prior to delivery.

The warranty covers material faults or production

faults. The warranty does not extend to product

parts subject to normal wear and tear or to fragile

parts which could be considered as consumable

parts such as switches, batteries or parts made of

glass.

PABH 20-Li B2

GB

│

CY

│

11 ■

The warranty does not apply if the product has

been damaged, improperly used or improperly

maintained. The directions in the operating

instructions for the product regarding proper use of

the product are to be strictly followed. Uses and

actions that are discouraged in the operating

instructions or which are warned against must be

avoided.

This product is intended solely for private use and

not for commercial purposes. The warranty shall

be deemed void in cases of misuse or improper

handling, use of force and modiﬁcations/repairs

which have not been carried out by one of our

authorised Service centres.

The warranty period does not apply to

■ Normal reduction of the battery capacity

overtime

■ Commercial use of the product

■ Damage to or alteration of the product by the

customer

■ Non-compliance with safety and maintenance

instructions, operating errors

■ Damage caused by natural hazards

Warranty claim procedure

To ensure quick processing of your case, please

observe the following instructions:

■ Please have the till receipt and the item number

(e.g.IAN12345) available as proof of purchase.

■ You will ﬁnd the item number on the type plate

on the product, an engraving on the product,

on the front page of the operating instructions

(below left) or on the sticker on the rear or

bottom of the product.

■ If functional or other defects occur, please

contact the service department listed either by

telephone or by e-mail.

■ You can return a defective product to us free of

charge to the service address that will be pro-

vided to you. Ensure that you enclose the proof

of purchase (till receipt) and information about

what the defect is and when it occurred.

You can download these instructions

along with many other manuals,

product videos and installation

software at www.lidl-service.com.

This QR code will take you directly

to the Lidl service page (www.lidl-service.com)

where you can open your operating instructions by

entering the item number (IAN) 123456.

Service

Service Great Britain

Tel.: 0800 404 7657

E-Mail: [email protected]

CY

Service Cyprus

Tel.: 8009 4409

E-Mail: [email protected]

IAN 339124_1910

Importer

Please note that the following address is not the

service address. Please use the service address

provided in the operating instructions.

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

GERMANY

www.kompernass.com

PABH 20-Li B2

■ 12

│

GB

│

CY

Translation of the original Conformity Declaration

We, KOMPERNASS HANDELS GMBH, documents oﬃcer: Mr. Semi Uguzlu, BURGSTR. 21,

44867 BOCHUM, Deutschland, hereby declare that this product complies with the following standards,

normative documents and the EC directives:

Machinery Directive

(2006/42/EC)

EC Low Voltage Directive

(2014/35/EU, charger only)

EMC (Electromagnetic Compatibility)

(2014/30/EU)

RoHS Directive

(2011/65/EU)*

* The manufacturer bears the full responsibility for compliance with this conformity declaration. The object of the

declaration described above complies with the requirements of the Directive 2011/65/EU of the European Parliament

and Council of 8 June 2011 on the limitations of use of certain dangerous substances in electrical and electronic

appliances.

Applied harmonised standards:

EN 60745-1:2009/A11:2010

EN 60745-2-6:2010

EN 60335-1:2012/A13:2017

EN 60335-2-29:2004/A2:2010

EN 62233:2008

EN 55014-1:2017

EN 55014-2:2015

EN 61000-3-2:2014

EN 61000-3-3:2013

EN 50581:2012

Type designation of machine: Cordless hammer drill PABH 20-Li B2

Year of manufacture: 11 - 2019

Serial number: IAN 339124_1910

Bochum, 23/01/2020

Semi Uguzlu

- Quality Manager -

The right to eﬀect technical changes in the context of further development is reserved.

PABH 20-Li B2

GB

│

CY

│

13 ■

Ordering a replacement battery

If you want to order a replacement battery for your appliance, you can do so easily via the internet on

www.kompernass.com or by telephone.

Due to limited stocks, this item may sell out in a relatively short time.

NOTE

► Online ordering of replacement parts might not be possible in some countries. In this is the case,

please contact the Service hotline.

Telephone ordering

Service Great Britain Tel.: 0800 404 7657

CY

Service Cyprus Tel.: 8009 4409

To ensure fast processing of your order, have the article number of your appliance to hand

(e.g. IAN 339124) in case of questions. The article number can be found on the type plate

or the title page of these instructions.

PABH 20-Li B2

■ 14

│

GB

│

CY

PABH 20-Li B2

HR

│

15 ■

Sadržaj

Uvod ..............................................................16

Namjenska uporaba .............................................................16

Prikazane komponente ...........................................................16

Opseg isporuke .................................................................16

Tehnički podaci .................................................................16

Opće sigurnosne napomene za uporabu električnog alata ..................17

1. Sigurnost na radnom mjestu .....................................................17

2. Električna sigurnost ............................................................18

3. Sigurnost osoba. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

4. Korištenje i rukovanje električnim alatom ............................................19

Korištenje i rukovanje alatom na baterije ..............................................19

5. Servis .......................................................................19

Sigurnosne napomene za punjače ..................................................20

Sigurnosne napomene za čekiće ....................................................20

Originalni pribor/dodatni uređaji ...................................................20

Prije uključivanja uređaja .............................................21

Punjenje paketa baterije (vidi sliku A) ...................................................21

Provjera stanja baterije ...........................................................21

Umetanje paketa baterija u uređaj/vađenje ...........................................21

Puštanje u pogon ....................................................21

Odabir alata za rad .............................................................21

Zamjena alata ..................................................................21

Umetanje SDS-alata/brzozatezni zaglavnik ...........................................22

Vađenje SDS-alata ...............................................................22

Rukovanje ..........................................................22

Odaberite način rada ............................................................22

Podesite smjer okretanja ..........................................................22

Uključivanje/isključivanje ..........................................................23

Podešavanje broja okretaja/udara ..................................................23

Održavanje i čišćenje .................................................23

Zbrinjavanje ........................................................23

Jamstvo tvrtke Kompernass Handels GmbH ..............................24

Servis ..............................................................25

Uvoznik ............................................................25

Prijevod originalne izjave o sukladnosti .................................26

Narudžba zamjenske baterije .........................................27

Telefonska narudžba .............................................................27

PABH 20-Li B2

■ 16

│

HR

AKU UDARNA BUŠILICA

PABH 20-LI B2

Uvod

Čestitamo na kupnji Vašeg novog uređa-

ja. Time ste se odlučili za vrlo kvalitetan

proizvod. Upute za uporabu sastavni su

dio ovog proizvoda. One sadrže važne napomene

za sigurnost, rukovanje i zbrinjavanje. Prije uporabe

proizvoda upoznajte se sa svim napomenama za

rukovanje i sa svim sigurnosnim napomenama.

Proizvod koristite isključivo na opisani način i u

navedenim područjima uporabe. U slučaju predaje

proizvoda trećim osobama, priložite i također pre-

dajte i svu dokumentaciju.

Namjenska uporaba

Aku udarna bušilica PABH 20-Li B2 (u nastavku

teksta „uređaj“) je prikladna za:

▯ Udarno bušenje u cigli, betonu i kamenu

▯ Bušenje u kamenu, drvetu i metalu

▯ Odvijanje u drvetu i metalu

Svaki drugi način uporabe i svaka izmjena uređaja

smatra se nenamjenskom i krije znatnu opasnost od

nezgode.

Proizvođač ne preuzima odgovornost za štete

nastale uslijed nenamjenskog korištenja uređaja.

Uređaj nije namijenjen za komercijalnu uporabu.

Prikazane komponente

Prihvatnik za SDS-Plus alate

Kapa za zaštitu od prašine

Čahura za blokadu

Prekidač „Bušenje/Udarno bušenje“

Prekidač za odabir smjera okretanja

Prekidač za uključivanje/isključivanje

Tipka za stanje baterije

LED indikator baterije

Paket baterija*

Tipka za deblokadu paketa baterija

LED radna svjetiljka

Brzi punjač*

Crvena LED svjetiljka za kontrolu punjenja

Zelena LED svjetiljka za kontrolu punjenja

Svrdlo sa šestokutnim umetkom

Svrdlo sa SDS-Plus prihvatom

Bitovi za zavrtanje

Brzozatezni zaglavnik

Univerzalni držač bitova

Mast

Opseg isporuke

1 Aku udarna bušilica PABH 20-Li B2

3 x 150 mm SDS-Plus svrdlo Ø 6/8/10 mm

3 x bitovi svrdla Ø 5/6/8 mm (HSS) sa šestokut-

nim prihvatom

6 x 50 mm bitovi (S2): 5.5/PH1/PZ1/PZ2/PZ2/

T20/T25

2 x bitovi PH2 (50 mm)

1 x Produživač bitova (šestokutni prihvat)

1 x 10 mm brzozatezni zaglavnik za svrdlo

s okruglim nastavkom (SDS-Plus prihvat)

1 Kofer za nošenje

50 g mast

1 Upute za uporabu

Tehnički podaci

Aku udarna bušilica PABH 20-Li B2

Nazivni napon 20 V

(istosmjerna struja)

Broj okretaja u praznom

hodu n

0

0–900 min

-1

Broj udara 0–5000 min

-1

Snaga udara ≥ 1 Joule

Maks. promjer bušenja 8 mm za metal

10 mm za beton

16 mm za drvo

Paket baterija PAP 20 A1*

Tip LITIJ-IONSKA

Nazivni napon 20 V

(istosmjerna struja)

Kapacitet 2 Ah

Broj ćelija 5

Brzi punjač baterija PLG 20 A1*

ULAZ/Input

Nazivni napon 230–240 V ∼, 50 Hz

(izmjenična struja)

Nazivna snaga 65 W

Osigurač (unutarnji) 3,15 A

T3.15A

Pagina se încarcă ...

Parkside 339124 1910 Translation Of The Original Instructions

Acest manual este potrivit și pentru

Parkside 339124 1910 Translation Of The Original Instructions

Lucrări conexe

Alte documente