Indesit FT M11 82Y EU Setup and user guide

Categorie
Uscătoare
Tip
Setup and user guide
You can download the Safety Instructions, User Manual, Product Fiche and Energy data by:
Visiting our website - docs.whirlpool.eu
Using QR Code
Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When
contacting our After-sales Service, please state the codes provided on your product’s identi cation plate.
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.
In order to receive a more complete assistance,
please register your product on
www.whirlpool.eu/register
EN
Quick guide
Before using the appliance carefully read the Safety Instructions.
xxxxxxxxxxxx
xxxx
Before using the appliance carefully read the Safety Instructions.
xxxxxxxxxxxx
xxxx
PROGRAMS
Eco Cotton kg Max*
Standard cotton programme, suitable to dry normally wet cotton
laundry. Most ecient programme in terms of energy consumption
for drying cotton laundry. The values on the Energy Label are based on
this programme.
Mixte kg 4
This programme is ideal for drying cotton and synthetic fabrics
together.
Bed Linen Kg Max*
This programme is intended for drying cotton sheets.
Shirts kg 3
This is a programme for Shirts made from cotton or cotton
blend/synthetics.
Sport kg 4
For drying sports garments made of synthetics or cotton.
Duvet
Programme intended to dry bulky garments, as single duvet.
Jeans kg 3
For drying cotton jeans-wear and garments made of robust
cotton, like denim, such as trousers and jackets.
Easy Ironing
This cycle allows to extend the bres of garments thus making
ironing and folding easier. Do not use in case of garments that are
still wet. Suitable for small loads of cotton textiles or cotton blends.
Refresh
A short programme suitable for refreshing bres and garments by
means of fresh air. Do not use with garments that are still wet. It can be
used on with any load size but is more eective with small loads. The
cycle duration is about 20 minutes.
FIRST TIME USE
Make sure that the water tank is correctly inserted. Make sure
that the drain hose on the back of the dryer is xed correctly,
either to the dryers water tank, or to your domestic sewage
system.
The dryer should be installed in environment in a room
temperature range of 20°to 23°C for optimum performance. But
will function if the room is between 14 and 30°C. Before you use
your dryer ensure that it has been in a upright position for at
least 6 hours.
DAILY USE
Doing this will keep your machine working at its BEST!
Remember to empty your water tank after each drying
cycle.Remember to clean your lters after each drying
cycle. (Refer to section Care & Maintanence).
1. Open the door and load garments. Always refer to instructions
on clothing labels and the max loads indicated in the programme
section. Empty pockets. Make sure garments do not get caught
between the door and/or the door lter.
2. Close the door.
3. Press the button On/O.
4. Select the programme according to the laundry type.
5. Select the options, if necessary.
6. To start the cycle, press the Start/Pause button.
7. At the end of the drying cycle, a buzzer will beep. An indicator on
the control panel signals the end of the cycle. Pull the load out
immediately to prevent the formation of creases on laundry
8. Turn the machine o by pressing the button On/O, open the
door and pull clothing out. If the machine is not switched o
manually, after about a quarter of an hour from the cycle end, the
appliance turns o automatically to save energy.
If this last stage is not carried out immediately, some machines
and/or some programmes/options are equipped with Crease Care
system. For some hours, after the end of drying, the drum rotates
at regular intervals to prevent the formation of creases. In case of
power failure, it is necessary to press the button Start/Pause to
restart the cycle.
OPENING OF THE DOOR DURING THE CYCLE
During operation, it is possible to open the door. After having
closed it, press the button Start/Pause again to restart the dryer.
*MAX LOAD 8 Kg (Dry load)
CARE LABEL
Always check the care labels, especially when placing garments in
the tumble dryer for the  rst time. Below are the most commonly
used symbols:
May be tumble dried.
Do not tumble dry.
Tumble dry – high heat.
Tumble dry – low heat.
CONTROL PANEL
1 ON/OFF button (Reset if long pressed)
2 Programme selection Knob
3 Start/Pause
Options Buttons*
4 Dryness Level
5 Start Delay
6 Timed Drying
7 Cycle End
8 Rapid (Key lock if long pressed)
9 Fresh Care+ (Mute if long pressed)
*Note: some models may have the wording in full instead of the icons
INDICATORS
Dryness Level: Iron Dry - Hanger Dry - Cupboard Dry - Extra Dry
Cycle phase: Drying - Cool Down - End of cycle.
Empty Water tank - Clean Door lter: primary, secondary Autoclean
Refer to Troubleshooting section: Failure: Call after sales service
DEMO
Demo Mode
1
3
2
9
7
8
4 56
3’’
3’’
1
3
2
9
7
8
4 56
3’’
3’’
h
h
OPTIONS BUTTONS
These buttons serves to personalise the selected programme
according to personal requirements. Not all options are available
for all programmes. Some options are incompatible with the
ones previously set. The buzzer and/or blinking indicators will
signal the incompatibility. If the option is available, the option
indicator will stay on. Some options may be kept in the memory
of the programme if selected in the previous drying.
Rapid 30' kg 0,5
Ideal for drying cotton garments spun at high speed in the
washing machine.
Coloured kg Max*
Programme for gentle drying suitable for coloured garments.
Silk kg 0,5
Gentle drying of silk garments.
Wool kg 1
Programme for drying wool clothing. It is advisable to turn
the garments inside out before drying. Leave to dry naturally the
heaviest edges that are still damp.
Delicates kg 2
For drying delicate laundry which needs gentle treatment.
Synthetics kg 4
For drying laundry made of synthetic bres.
OPTIONS
After selecting the programme, the various options can be
set, if necessary.
Dryness Level
Press the related button several times to obtain a dierent
level of residual moisture on garments. An indicator signals the
level being selected.
Iron Dry: a very delicate ironing. Suitable for making ironing
of garments easier immediately after the end of the cycle.
Hanger Dry: a level intended for delicate garments ready to
be hanged.
Cupboard Dry: the garments are ready to be folded and put
away.
Extra Dry: used for garments to be worn at the end of the
cycle.
Timed drying
This option allows to set the drying time. Press the
corresponding button to set the required time for drying. After
having reached the max. settable time, a further pressure of the
button resets the option. An indicator on the control panel signals
the time being selected.
h
Start Delay
This option allows you to set the delay of the cycle start. Press
the corresponding button several times to obtain the required
delay. After having reached the max. settable time, the option is
reset by pressing the button again. An indicator on the control
panel signals the time being selected. After having pressed the
button Start/Pause, the machine signals the remaining time
for the cycle start. In case of door opening, after closing, it is
necessary to press the button Start/Pause.
Rapid
Enables quicker drying.
Fresh Care+
If garments are left inside the drum after the end of the
cycle, they are subject to bacterial proliferation. This option allows
to prevent this proliferation by controlling the temperature and
the rotation of the drum. This treatment has a max. duration of 6
hours after the end of the programme set. This option remains in
memory if selected in the previous drying.
If this option is used together with the Start Delay, a crease
treatment (a periodic rotation of the drum) is added in the Start
Delay phase.
Key Lock
This option makes all machine controls inaccesible, except the
button On/O. When the machine is on: to activate the option,
keep the button pressed until the indicator goes on. To disable the
option, keep the button pressed until the indicator goes o. This
option remains in memory if selected in the previous drying.
Cycle End
This option activates a prolonged buzzer at the end of the
cycle. Enable it if you are not sure to hear the normal sound at the
end of the cycle. This option remains in memory if selected in the
previous drying.
Mute
This option turns o all sounds of control panel. Only
warnings remain active.
to activate the option, keep the button pressed until the indicator
goes on.
to disable the option, keep the button pressed until the indicator
goes o.
Ciclul de uscare pentru produse din
lână al acestei mașini a fost aprobat de
The Woolmark Company pentru usca-
rea articolelor de îmbrăcăminte din lână
care au pe eticheta mențiunea „spălare
manuală, cu condiția ca acestea sa  e
uscate conform instrucțiunilor furni-
zate de producătorul acestei mașini.
Respectați mențiunile de îngrijire de pe etichetă pentru alte instrucțiuni
pentru rufele de spălat. . Simbolul Woolmark este o marcă
certi cată în multe țări.
M1768
The duration of these programs will depend on the size of the
load, types of textiles, the spin speed used in your washer and
any extra options selected. In machines equipped with display,
the duration of the cycles is shown on the control panel. The
remaining time is constantly checked and adjusted during the
drying cycle to show the best possible estimate.
You can download the Safety Instructions, User Manual, Product Fiche and Energy data by:
Visiting our website - docs.indesit.eu
Using QR Code
Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When
contacting our After-sales Service, please state the codes provided on your product’s identi cation plate.
THANK YOU FOR BUYING A INDESIT PRODUCT.
In order to receive a more complete assistance,
please register your product on
www.indesit.eu/register
EN
Quick guide
Before using the appliance carefully read the Safety Instructions.
xxxxxxxxxxxx
xxxx
Before using the appliance carefully read the Safety Instructions.
xxxxxxxxxxxx
xxxx
CARE AND MANTENANCE
Unplug the dryer during the cleaning and maintenance
procedures.
Emptying the water tank after each cycle (see Fig. A).
Pull the container out of the dryer and and empty it into a
sink or other suitable drain, then place it back. Do not use the dryer
without having inserted the container back in place.
Cleaning the primary door lter after each cycle (see Fig. B).
After each cycle, pull the primary door lter out and clean it by
removing the lint from the lter surface under running water or
using a vacuum cleaner.
Cleaning the secondary door filter when the relevant
indicator turns on (see Fig. C).
Pull the secondary door lter out and clean it in all its parts by
washing it under running water or using a vacuum cleaner.
Do not use the dryer without having inserted all lters back
in place properly rst.
The lters are essential parts for drying. They are intended
to collect the lint formed during drying process. In case
of clogged lters, the air ow inside the dryer would be
seriously aected: the drying times would be longer, the
energy consumption would increase and the dryer could be
damaged. If these procedures are not carried out properly,
the dryer may not start.
Autoclean
The maintenance of the bottom lter of this model is
automatic. The dryer carries out cleaning when the sensors signal
the need to do so. In this case, the machine goes on working even
when the drying cycle is completed. An indicator on the control
panel will signal the maintenance. Do not switch the machine o
during this phase.
PRODUCT DESCRIPTION
1. Water Tank
2. Air Intake
3. Door lter
B primary
C secondary
TRANSPORT AND HANDLING
Never lift the dryer by holding it at the worktop.
1. Unplug the dryer.
2. Make sure that door and water tank are properly closed.
3. If the drain hose is connected to your sewage system, x the
drain hose on the rear of the dryer again (see Installation Guide).
Heat Pump System
The heat pump contains uorinated greenhouse gases,
contained in a hermetically sealed unit. This sealed unit contains
0,18 kg of the F gas R134a. GWP = 1430 (1 t CO2).
Power consumption
o-mode (Po) - Watts 0.50
left-on mode (Pl) - Watts 1.00
Programs Kg kWh Minutes
Eco Cotton *
8 1.86 194
Eco Cotton
4 1.09 126
Synthetics 4 0.83 109
*This is the reference programme for the energy label and suitable to
dry normal wet cotton laundry. This is the most ecient programme
in terms of energy consumption for drying wet cotton laundry.
(Standard/Default starting conguration)
1
3
2
AB
C
You can download the Safety Instructions, User Manual, Product Fiche and Energy data by:
Visiting our website - docs.whirlpool.eu
Using QR Code
Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When
contacting our After-sales Service, please state the codes provided on your product’s identi cation plate.
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.
In order to receive a more complete assistance,
please register your product on
www.whirlpool.eu/register
EN
Quick guide
Before using the appliance carefully read the Safety Instructions.
xxxxxxxxxxxx
xxxx
Before using the appliance carefully read the Safety Instructions.
xxxxxxxxxxxx
xxxx
TROUBLESHOOTING
Before contacting the Service Centre, refer to the table below. Often the malfunctions are minor and can be solved in few minutes
Possible cause
Solution
The tumble
dryer does not
turn on.
The plug is not inserted into the socket.
Insert the plug into the socket.
The plug is faulty.
Try to plug another appliance in the same socket. Do not use
connecting electrical devices to the socket, as adapters or extensions
A power failure occurred. Await the reactivation of the power supply.
The tumble
dryer does not
start
The door is open.
Close the door.
A time delay for the cycle start was set.
For machines equipped with this function: await the end of the delay
set or switch the machine o to reset it. Refer to the section Options.
The button Start/Pause was not pressed to start
the program.
Press the button Start/Pause.
The function Key Lock was enabled (in case of
machines equipped with this option).
Refer to the option section and, if the Key Lock is present, disable it.
Switching the machine o is not enough to disable this option.
The drying
times are very
long
An appropriate maintenance was not carried
out.
Refer to the section Care & Maintenance and perform the operations
described.
The programme, the time and/or the drying
level set are not suitable for the type and the
amount of load inserted into the dryer.
Refer to the section programmes and options to  nd the programme
and the options most suitable for the type of load.
The garments are too wet.
Carry out a washing cycle with higher spin speed to remove as much
water as possible.
The dryer may be overloaded.
Refer to the programme section to check the max. load for each
programme.
The programme
A power failure occurred might have occurred.
In case of power failure, it is necessary to press the button Start/Pause
to restart the cycle.
Lights on or  ashing
Water tank The water tank is full. Emtpy the water tank. Refer to the section Care & Maintenance.
and/or bottom
Failure of the air  ow necessary for machine
operation.
Clean the door  lter and the bottom one and check whether air
intake is free. Carrying out these operations improperly may cause
damages.
Bottom  lter* The bottom  lter requires cleaning. Clean the bottom  lter. Refer to section Care & Maintanence.
DEMO
The cycle lasts
few minutes.
The dryer is in DEMO mode. The DEMO
indicator is on.
Disable the DEMO mode. The following actions must be carried out
in sequence, without breaks. Switch the machine on and then switch
it o again. Press the Start/Pause button until the buzzer is heard.
Switch the machine on again. The “DEMO indicator  ashes and then
turns o .
The presence
of wrench
symbol signals a
malfunction.
The machine sensors detected a failure.
Switch the dryer o and unplug it. Open the door immediately and
pull laundry out, to allow the heat to dissipate. Wait for about 15
minutes. Reconnect the dryer to the power supply, load the laundry
and restart the drying cycle. If the problem still occurs, contact
the After-Sales Service Centre and communicate the letters and
digits  ashing on the display.
For instance: F3 and E2
*Note: some models are self-cleaning and not equipped with bottom  lter. Please refer to the section Care & Maintenance.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Indesit FT M11 82Y EU Setup and user guide

Categorie
Uscătoare
Tip
Setup and user guide

în alte limbi