Hendi 225516 Manual de utilizare

Marca: Hendi

Model: 225516

Categorie: Plite

Tip: Manual de utilizare

CONVECTION BAKERY

OVEN WITH HUMIDIFIER

4X 600X400 MM

PIEC PIEKARNICZY KONWEKCYJNY

Z NAWILŻANIEM 4X 600X400 MM

Item: 225516

You should read this user manual carefully before

using the appliance

Bevor Sie das Gerät in Betrieb nehmen, sollten

Sie diese Gebrauchsanweisung aufmerksam lesen

Alvorens de apparatuur in gebruik te nemen dient

u deze gebruiksaanwijzing aandachtig te lezen

Przed uruchomieniem urządzenia należy koniecznie

dokładnie przeczytać niniejszą instrukcję obsługi

Lisez attentivement ce mode d’emploi avant d’utiliser

l’appareil .

Prima di utilizzare l’apparecchio in funzione leggere

attentamente le istruzioni per l’uso.

Citiţi cu atenţie prezentul manual de utilizare înainte

de folosirea aparatului

Внимательно прочитайте руководство пользователя

перед использованием прибора

User manual

Gebrauchsanweisung

Gebruiksaanwijzing

Instrukcja obsługi

Mode d’emploi

Istruzioni per l’utente

Instrucţiunile utilizatorului

Руководство по эксплуатации

Keep this manual with the appliance.

Diese Gebrauchsanweisung bitte beim Gerät aufbewahren.

Bewaar deze handleiding bij het apparaat.

Zachowaj instrukcję urządzenia.

Gardez ces instructions avec cet appareil.

Conservate le istruzioni insieme all’apparecchio.

Păstraţi manualul de utilizare alături de aparat.

Хранить руководство вместе с устройством.

For indoor use only.

Nur zur Verwendung im Innenbereich.

Alleen voor gebruik binnenshuis.

Do użytku wewnątrz pomieszczeń.

Pour l’usage à l’intérieur seulement.

Destinato solo all’uso domestico.

Numai pentru uz casnic.

Использовать только в помещениях.

INDEX

1. TECHNICAL SERVICE ....................................................... 3

2. IMPORTANT SAFETY REGULATIONS ............................... 3

3. GENERAL WARNINGS...................................................... 4

4. TECHNICAL SPECIFICATIONS ......................................... 5

5. INSTRUCTIONS FOR THE INSTALLER ............................. 6

6. USE INSTRUCTIONS (FOR THE USER) ............................. 8

7. RESIDUAL RISKS (FOR THE USER) ................................. 9

8. HOW TO USE THE CONTROL PANEL ................................ 10

9. OVEN COOKING ................................................................ 11

10. COOKING ADVICE ............................................................. 11

11. ROUTINE CLEANING AND MAINTENANCE ..................... 12

12. TECHNICAL ASSISTANCE ................................................ 12

13. WIRING LAYOUTS ............................................................ 13

14. WARRANTY ...................................................................... 13

15. DISCARDING & ENVIRONMENT ....................................... 14

Dear Customer,

Thank you for purchasing this Hendi appliance. Before using the appliance for the first time, please read

this manual carefully, paying particular attention to the safety regulations outlined below.

1. TECHNICAL SERVICE

A technical check-up once or twice a year helps

prolong the life of the appliance and guarantees

better operation.

Make sure that assistance is carried out solely and

exclusively by qualiﬁ ed personnel.

For any spare parts orders or for any information

about the appliance, always mention the serial

number and model (data indicated on the “techni-

cal data” plate at the rear of the oven).

2. IMPORTANT SAFETY REGULATIONS

• This appliance is intended for commercial use only and must not be used for

household use.

• The appliance must only be used for the purpose for which it was intended and

designed. The manufacturer is not liable for any damage caused by incorrect

operation and improper use.

• Keep the appliance and electrical plug away from water and any other liquids. In

the event that the appliance should fall into water, immediately remove plug from

the socket and do not use until the appliance has been checked by a certiﬁ ed

technician. Failure to follow these instructions could cause a risk to lives.

• Never attempt to open the casing of the appliance yourself.

• Do not insert any objects in the casing of the appliance.

• Do not touch the plug with wet or damp hands.

• Danger of electric shock! Do not attempt to repair the appliance yourself. In case

of malfunctions, repairs are to be conducted by qualiﬁ ed personnel only.

• Never use a damaged appliance! Disconnect the appliance from the electrical

outlet and contact the retailer if it is damaged.

• Warning! Do not immerse the electrical parts of the appliance in water or other

liquids. Never hold the appliance under running water.

• Regularly check the power plug and cord for any damage. If the power plug or

power cord is damaged, it must be replaced by a service agent or similarly quali-

ﬁ ed persons in order to avoid danger or injury.

• Make sure the cord does not come in contact with sharp or hot objects and keep

it away from open ﬁ re. To pull the plug out of the socket, always pull on the plug

and not on the cord.

• Ensure that the cord (or extension cord) is positioned so that it will not cause a trip

hazard.

• Always keep an eye on the appliance when in use.

• Warning! As long as the plug is in the socket the appliance is connected to the

power source.

• Turn off the appliance before pulling the plug out of the socket.

• Never carry the appliance by the cord.

• Do not use any extra devices that are not supplied along with the appliance.

• Only connect the appliance to an electrical outlet with the voltage and frequency

mentioned on the appliance label.

• Connect the power plug to an easily accessible electrical outlet so that in case of

emergency the appliance can be unplugged immediately. To completely switch off

the appliance pull the power plug out of the electrical outlet.

• Always turn the appliance off before disconnecting the plug.

• Never use accessories other than those recommended by the manufacturer. Fail-

ure to do so could pose a safety risk to the user and could damage the appliance.

Only use original parts and accessories.

• This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge.

• This appliance must not be used by children under any circumstances.

• Keep the appliance and its cord out of reach of children.

• Always disconnect the appliance from the mains if it is left unattended or is not in

use, and before assembly, disassembly or cleaning.

• Never leave the appliance unattended during use.

3. GENERAL WARNINGS

Very important!: keep this instruction book together with the appliance for future

consultation.

These warnings were drafted for your safety and for that of others. Please read

them carefully before installing or using the appliance:

• If, on receipt of the goods, the packaging is damaged, write the following on the

delivery note: “I REVERSE THE RIGHT TO CONTROL THE GOODS”, specify the

damage and get the driver to sign in acceptance; send a claim in writing to the

seller within 4 calendar days from the date of receipt. No claim shall be accepted

after such period.

• The warehouse inside temperature must not be lower than -9°C; otherwise, the

thermostat (regulation and safety thermostat) control devices of the machine will

be damaged. Failure to observe this prohibition invalidates any responsibility of

the manufacturer of the machine.

• The appliance is intended for professional use and must be utilised by qualiﬁ ed

personnel trained to use it.

• Any modiﬁ cation which may be necessary on the electrical system to enable in-

stallation of the appliance, must be carried out solely by competent personnel.

• It is dangerous to modify or attempt to modify the characteristics of this appliance.

• Never clean the appliance with direct water jets, because, if any water enters, it

could limit the machine’s safety.

• Before doing any maintenance or cleaning jobs, disconnect the appliance from

the electrical mains and allow it to cool.

• When the tilting door is wide open, do not put anything

on the surface, be-

cause the door hinges could be irreparably damaged.

• Do not attempt to carry out the periodic controls or any repairs by yourself. Con-

tact the nearest Service Centre and use only original spare parts.

N.B.: Improper or incorrect use and failure to observe the installation instructions

shall release the manufacture from all responsibility. In this connection, the direc-

tives in the “POSITIONING” paragraph must be strictly observed.

4. TECHNICAL SPECIFICATIONS

Dimensions of appliance LxDxH (mm) 790x750x635

Weight (Kg) 50,4

Convection heating element (kW) 3,0

Max. absorbed power (kW) 3,4

Power supply voltage (V) 230V ~50/60Hz

Power cable diameter 3x1,5 mm

Type of cable H07RN-F

Connecting electric cable Type Y

Class I

Degree of protection against humidity IPX3

Water pressure (kPa) 100-200

The noise level of the appliance in operation is below 70 dB (A).

The II technical data II plate is positioned on the rear panel of the appliance.

The manufacturer and dealer is not liable for any

inaccuracies due to printing errors or transcrip-

tion, in this manual. In line with our policy of con-

tinuous improvement products, we reserve the

right to make modification of the product, pack-

aging and specifications contained in the Docu-

mentation without prior notice.

5. INSTRUCTIONS FOR THE INSTALLER

The following instructions are aimed at the quali-

ﬁ ed installer, to ensure that he carries out the in-

stallation, adjustment and maintenance operations

as correctly as possible and according to current

legal regulations. Any operation must be per-

formed with electrical power cut to the appliance.

Before using the appliance, carefully remove the

special adhesive ﬁ lm protecting the parts in stain-

less steel. Do not leave any glue residues on the

surfaces. If necessary, remove them at once, with

an appropriate solvent.

5.1 POSITIONING

Position the appliance perfectly horizontally on a ta-

ble

or similar support (the table or support must

be at least 85 cm above the ﬂ oor). Position it at a

distance of not less than 10 cm from the side and

rear walls, to enable natural ventilating air to cir-

culate freely around it. The appliance is ventilated

through speciﬁ c openings on the metal walls of the

outer housing, and ensures efﬁ ciency and long-life.

For this reason it is strictly forbidden to obstruct

these ventilation openings, even partially or for

short periods. Failure to observe this speciﬁ c pro-

hibition releases the manufacturer of the appliance

from all responsibility and immediately voids any

guarantee rights for the said appliance, because its

constructive conformity has been voluntarily com-

promised. Furthermore, the appliance is not suita-

ble for embedding and for grouped positioning with

other identical appliances.

5.2 ELECTRICAL CONNECTION

The appliance must be connected to the electri-

cal mains according to current legal regulations.

Before making the connection, make sure of the

following:

• the voltage and frequency values of the power

supply system match the values on the “technical

data” plate afﬁ xed on the appliance;

• the limiting valve and the system are able to

support the appliance’s load (see the “technical

data” plate);

• the power supply system has an adequate

earth connection according to current legal

regulations;

• a omnipolar switch with minimum between-con-

tacts aperture of the overvoltage category III

(4000 V), sized to the load and conforming to

current legal regulations, is ﬁ tted between the

appliance and the mains in the direct connection

to the mains;

• the omnipolar switch used for connection is easy

to reach when the appliance is installed;

• the yellow/green earth wire is not interrupted by

the switch;

• the power supply, when the appliance is operat-

ing, must not deviate from the rated voltage value

by ±10%;

• make sure that after inserting the power supply

cord into the terminal block it does not come into

contact with any of the cooking range’s hot parts.

• if the supply cable is damaged then it must be re-

placed by the manufacturer or by your technical

support or by a qualiﬁ ed person to avoid any risk.

1 Water inlet 4 Caution! Hot surface

2 Steam outlet 5 Radial motoventilators

3 Electric cable ﬁ xer

5.3 CONNECTION TO THE WATER MAINS

The appliance must be fed with softened drinking

water, with hardness from 0.5° F to 3° F (it is oblig-

atory to use a softener to reduce the formation of

lime inside the cooking chamber) and pressure in

the range from 100 to 200 kPa (1.0 - 2.0 bar).

Connection to the water mains should be made

through the threaded 3/4” solenoid-valve on the

rear (on the bottom) of the appliance, ﬁ tting in be-

tween a mechanical ﬁ lter and an on/off tap (before

you connect the ﬁ lter, allow a certain quantity of

water to ﬂ ow out in order to drain any waste from

the pipe).

5.4 CONNECTING THE POWER CABLE

To access the terminal board, just remove the ap-

pliance’s rear sidepanel. Loosen the cable gripper

and allow the cable to pass through it. Arrange the

conductors so that the earth conductor is the last

to detach from its terminal if the cable goes into

a state of faulty traction. Connect the phase con-

ductors to the terminals marked “L1” and “L2”,

connecting the neutral conductor to the terminal

marked “N” and the earth conductor to the ter-

minal marked with the symbol according to the

following lay-out:

230V

L2 L1 N

400V / 2N

L2 L1

(this electrical connection lay-out is located near

the power supply terminal board ). Tighten the

cable gripper and re-ﬁ t the rear side-panel of the

appliance.

The appliance must be connected to an equipoten-

tial system whose efﬁ ciency must ﬁ rst be checked

according to current legal regulations.

This connection must be made between different ap-

pliances by using the appropriate terminal marked

with the symbol . The equipotential conductor

must have a minimum diameter of 2,5 mm². The

equipotential terminal is at the rear of the appliance.

5.5 SAFETY THERMAL BREAKER

The appliance has a manually reset safety thermal

breaker. It protects against excessive dangerous

over-temperatures which could be accidentally

generated inside the appliance. This device is lo-

cated on the back of the oven.

6. USE INSTRUCTIONS (FOR THE USER)

This appliance is not intended for use by persons

(including children) with reduced phycal, sensory

or mental capabilities, or lack of experience and

knowledge. Unless they have beengiven supervi-

sion or instruction concerning use of appliance by

a person responsible for their safety.

Children should be supervised to ensure that they

do not play with the appliance.

For ﬁ rst use, we advise you to let the appliance to

run load-free at maximum temperature for about

one hour. In this way, any unpleasant smells due

to thermal insulation and residual work grease are

eliminated.

This appliance must be used solely for the purpose

for which it was expressly designed, i.e. cooking

foods in the oven. Any other use is considered

unsuitable.

The appliance can be used: for all oven cooking of

deserts, pizzas, meat, ﬁ sh, vegetables, as well as

for gratinating, and for re-conditioning cooled and

frozen foods.

When placing food in the cooking compartment,

leave a space of at least 40 mm between pans in

order not to over-obstruct air circulation.

Do not use pans with higher than necessary edges:

edges are barriers which prevent the circulation of

hot air.

Warm up the oven before every cooking operation

to obtain maximum uniformity.

Do not salt foods in the cooking compartment.

6.1 PLACING TRAYS AND CONTAINERS IN THE OVEN CHAMBER

✔

Never stack food items on top of each other. Divide them evenly on the tray or GN container.

6.2 KEEP VERTICAL SPACE BETWEEN TRAYS AND/OR GN CONTAINERS

In order to ensure optimum circulation of hot air in the oven chamber, a minimum vartical distance of 40 mm

between the trays or GN containers is required.

✔

6.3 POSITIONING OF TRAYS AND/OR GN CONTAINERS IN THE OVEN CHAMBER

To ensure optimum hot air circulation:

• Don’t position the tray or GN container against the fan

• Position them evenly and in the middle in the oven chamber

✔

7. RESIDUAL RISKS (FOR THE USER)

After a cooking operation, open the door cautiously,

to avoid a violent outﬂ ow of heat which could cause

burns.

While the oven is in operation, pay attention to the

hot zones (marked on the appliance) of its external

surfaces.

Place the machine on a bench or similar support,

at a height of at least 85 cm from the ﬂ oor.

The bench or support must be able to support the

weight of the machine and house it correctly.

The appliance contains electrical parts and must

never be washed with a jet of water or steam.

The appliance is electrically connected: before at-

tempting any cleaning operation, cut power to the

appliance.

To prevent incorrect connection of the appliance,

the relevant electrical and water connections are

marked by identiﬁ cation plates.

Do not use the door handle to move the appliance

(the glass panel may break).

When the tilting door is wide open, do not use the

internal surface to place objects to avoid damaging

permanently the door hinges.

8. HOW TO USE THE CONTROL PANEL

Fig. 1 Fig. 2

Programmer indicator light

Temperature indicator light

Humidiﬁer switch

Programming cooking time

To run the oven, turn the programmer knob (Fig.

1) in line with symbol (continuous operation) or

in line with the selected cooking time (up to 120

minutes). In the second case, end of cooking is sig-

nalled by the oven switching OFF automatically.

Programming cooking temperature

Turn the knob of the adjustment thermostat (Fig. 2)

in line with the temperature selected for cooking.

Humidifier key

To produce vapour inside the oven while the oven

is operating and the chamber is hot, press the key

(commanding the humidiﬁ er) for a few seconds.

Control thermostat indicator light

The control thermostat orange indicator light goes

OFF whenever the programmed temperature is

reached inside the cooking compartment. It lights

up again when the thermostat is tripped to re-es-

tablish this temperature.

“End of cooking” programmer indicator light

The programmer green indicator light indicate that

the oven is operating and that cooking time is active.

Oven internal light

The light is always on when the oven is operating.

To switch off the oven

Turn OFF the knobs of the “end of cooking” pro-

grammer and of the thermostat. When you have

ﬁ nished using the oven, shut off the water ON/OFF

tap upstream of the appliance and cut out electric

power.

9. OVEN COOKING

For cooking, before putting food in, warm up the

oven to the required temperature. When the oven

reaches the temperature, put the food in and check

cooking time. Switch off the oven 5 minutes before

the theoretical time in order to recover stored heat.

Convection cooking

Water is ﬁ lled in a drip box behind the air conveyor

grid.

Sort of activation: with button or with knob.

Ideal for recipes that need humidity (for example

roast meat).

Activate the oven and turn the thermostat knob in

line with the required temperature.

Defreezing

Activate the oven and turn the thermostat knob to

the OFF position.

Humidification

While the oven is functioning press the humidiﬁ ca-

tion botton to generate steam in the already heated

cooking chamber.

10. COOKING ADVICE

Convection cooking

Heat is transferred to the foods by pre-heated air,

forced to circulate by in the cooking chamber. The

heat quickly and uniformly reaches all parts of the

chamber, enabling simultaneous cooking of dif-

ferent types of food (providing they have the same

cooking temperature), placed on the shelves with-

out mixing tastes and smells. Convection cooking

is particularly convenient for rapid defreezing, and

for sterilising preserves and drying mushrooms

and fruit.

Cooking desserts

Desserts require a very high temperature (usually

from 150 to 200°C) and a pre-heated oven (about

ten minutes). The oven door must not be opened

until at least 3/4 of the cooking time has elapsed.

Whipped dough must be difﬁ cult to detach from

a spoon because excessive ﬂ uidity would prolong

cooking time to no avail.

Cooking meat

Meat to be cooked should weight at least 1 Kg to

prevent it drying too much. Very tender red meats

to be cooked rare, which must be cooked on the

outside to keep all their gravy, require short cook-

ing time at high temperature (200-250°C). The

gravy ingredients must be placed immediately in

the pan only if the cooking temperature is brief,

otherwise they should be added during the last

half-hour. You can check the degree of cooking by

squashing the meat with a spoon: if the meat does

not yield, it is correctly cooked. For roast beef and

ﬁ llet, which must remain pink inside, cooking time

must be very brief. Meats may be placed on a plate

suitable for oven cooking or directly on the grill,

under which you should place a tray to collect the

gravy. When cooking has ﬁ nished, we advise you to

wait for 15 minutes before cutting the meat so that

the gravy does not come out. Before being served,

the dishes may be kept hot in the oven at minimum

temperature.

11. ROUTINE CLEANING AND MAINTENANCE

(WARNING: Cut power to the appliance before every operation)

General cleaning

Clean the oven when it is cold. Wash enamelled

parts with lukewarm water and soap, do not use

abrasive products, steel wool, or acids, which could

ruin them. To clean the steel parts, do not use

products containing chlorine (sodium hypochlorite,

hydrochloric acid, etc) even if diluted. Use speciﬁ c

off-the-shelf products or a little hot vinegar. Rinse

thoroughly with water and dry with a soft cloth.

Clean the glass door of the oven with hot water only,

and do not use rough cloths. Do not allow foods (es-

pecially acid foods such as salt, vinegar, lemon, etc)

to stagnate on the stainless steel parts, because

they could deteriorate. Do not wash the appliance

with direct jets of water, because if water enters,

this could limit the appliance’s safety. Do not use

corrosive substances (e.g. hydrochloric acid) to

clean the oven’ s support bench.

Cleaning the oven

It is good practice to clean the oven interior at the

end of every day of duty. In this way it will be easier

to remove cooking residues, preventing them from

burning when the oven is next used. Clean it accu-

rately with hot water and soap or with the appropri-

ate off-theshelf products.

Cleaning the oven door

To clean the oven door thoroughly, proceed as

follows:

• fully open the door;

• insert the equipped plugs in the “A” holes on the

hinges (Fig. 4);

• lift the door gently and withdraw it (Fig. 5);

• put back the door in the initial position by operat-

ing

inverserly.

Replacing oven lamp

Electrically switch off the appliance; unscrew the

protective glass cap; unscrew the lamp and replace

it with another lamp suitable for high temperatures

(300°C), with the following characteristics:

• Voltage 230/240 V

• Power 15 W

• Fitting E 14

Reﬁ t the glass cap and power up the appliance.

Fig. 4 Fig. 5

12. TECHNICAL ASSISTANCE

Before leaving the factory, the appliance was com-

pletely regulated and tested by expert specialised

personnel to guarantee the best operating results.

All repairs and settings must be performed with ut-

most care and attention, respecting national safety

regulations in force. Always contact your retailer

or our nearest Service Centre, giving details of the

problem, the appliance model and the serial num-

ber (on the rating plate on the rear panel).

For any maintenance the user can contact Tecnoe-

ka by calling the telephone numbers on the cover

or going to www.tecnoeka.com.

13. WIRING LAYOUTS

M Power terminal board

Pr “End of cooking” programmer

MI Door microswitch

I Umidiﬁ er switch

T1 Safety thermostat

T2 Control thermostat

L1-L2 Lighting lamps

R1-R2 Circular heating elements

V1-V2 Radial motoventilators

V3 Motoventilatore tangenziale

E Water solenoid-valve

B1-B2 Contactor coils

S1 Programmer indicator light

S2 Thermostat indicator light

14. WARRANTY

Any defect affecting the functionality of the appli-

ance which becomes apparent within one year after

purchase will be repaired by free repair or replace-

ment provided the appliance has been used and

maintained in accordance with the instructions and

has not been abused or misused in any way. Your

statutory rights are not affected. If the appliance is

claimed under warranty, state where and when it

was purchased and include proof of purchase (e.g.

receipt). In line with our policy of continuous prod-

uct development we reserve the right to change the

product, packaging and documentation speciﬁ ca-

tions without notice.

Apart from the case when the customer cannot

produce the invoice or receipt proving the purchase

or when the above-mentioned terms are not com-

plied with, the warranty is expressly excluded in the

following cases:

• faults or breakage caused by the transport;

• wrong or incorrect installation of the product (for

instance because of insufﬁ cient draught of the

ﬂ ue or exhausts) in light of the instructions given

in the user’s handbook supplied with the product;

• inadequate or abnormal electrical, hydraulic

and/or gas supplies;

• carelessness, negligence or incompetence in us-

ing the product in light of the instructions given

in the user’s handbook supplied with the product;

• use of the product for uses different from the one

for which it was built or anyway in a manner not

compliant with the instructions given in the us-

er’s handbook supplied with the product;

• tampering with the product;

• adjustments and/or maintenance and/or repairs

carried out by unauthorised personnel and/or

with non original spare parts;

• inadequate or careless maintenance of the prod-

uct in contrast with the user’s handbook supplied

with the product;

• damages caused by ﬁ re, natural disasters and

accident as well as by any cause not attributable

to company HENDI.

The warranty explicitly excludes: varnished or

enamelled parts, knobs, handles, movable or re-

movable plastic parts, bulbs, glass parts, refracto-

ries and any accessories.

Company HENDI cannot be held responsible for

any damages, either direct or indirect, caused by

the product breaking down or following its non-use.

Any repairs carried out during the warranty do not

cause said warranty to be extended or renewed.

Nobody is authorised to modify the terms and con-

ditions of the warranty or to issue new verbal or

written warranties.

The warranty is valid only for appliances installed in

the European Union.

Warning for the Buyer:

The cooking appliance is designed only for cooking

purposes while the heating appliance is desi-

gned only for heating domestic environments;

2. Company HENDI

does not install the appliances;

the seller

shall be responsible for any installa-

tion carried out;

3. Company HENDI cannot be held responsible for

any damages, either direct or indirect, to people,

pets or property caused by the appliance bre-

aking down or following its non-use.

Company HENDI cannot be held responsible for any

inaccuracies due to misprints or mistakes in cop-

ying in this handbook. The Manufacturer reserves

the right to modify the products as he deems ﬁ t,

also in the interest of the user, without affecting the

vital characteristics of functionality and safety.

15. DISCARDING & ENVIRONMENT

At the end of the life of the appliance, please dis-

pose of the appliance according to the regula-

tions and guidelines applicable at the time. Throw

packing materials like plastic and boxes in the ap-

propriate containers.

INHALTSVERZEICHNIS

1. TECHNISCHER SERVICE ........................................................17

2. SICHERHEITSREGELN ...........................................................17

3. ALLGEMEINE HINWEISE ........................................................19

4. TECHNISCHE MERKMALE .....................................................20

5. ANWEISUNGEN FÜR DEN INSTALLATEUR ............................20

6. BEDIENUNGSANWEISUNGEN (FÜR DEN BENUTZER) ..........23

7. RESTRISIKEN (FÜR DEN BENUTZER)....................................24

8. GEBRAUCH DER BEDIEN BLENDE ........................................24

9. BACKEN ..................................................................................25

10. HINWEISE ZUM BACKEN .......................................................26

11. REINIGUNG UND GEWÖHNLICHE WARTUNG ........................26

12. TECHNISCHER KUNDENDIENST ...........................................27

13. SCHALTPLÄNE .......................................................................28

14. GARANTIE ...............................................................................28

15. ENTSORGUNG UND UMWELTSCHUTZ ...................................29

Sehr geehrte Kundin, sehr geehrter Kunde,

wir danken Ihnen für den Kauf des Gerätes Hendi. Machen Sie sich bitte mit dieser Anleitung noch vor der

Inbetriebnahme des Gerätes vertraut, um Schäden durch die unsachgemäße Bedienung zu vermeiden. Den

Sicherheitsregeln ist besondere Aufmerksamkeit zu widmen.

1. TECHNISCHER SERVICE

Eine technische Kontrolle ein oder zwei Mal pro

Jahr trägt zur Verlängerung der Lebensdauer

des Geräts bei und gewährleistet seinen optima-

len Betrieb. Sicher stellen, dass der Service aus-

schließlich von Fachpersonal ausgeführt wird. Bei

eventuellen Ersatzteilbestellungen oder für Aus-

künfte über das Gerät immer die Seriennummer

und das Modell angeben (diese Daten beﬁ nden

sich auf dem Schild „Technische Daten” an der

Ofenrückseite).

2. SICHERHEITSREGELN

• Die unsachgemäße Bedienung des Geräts kann zur schweren Beschädigung des

Geräts sowie zu Verletzungen führen.

• Das vorliegende Gerät ist ausschließlich für den gewerblichen Gebrauch be-

stimmt und darf nicht im Haushalt verwendet werden.

• Das Gerät ist ausschließlich zu dem Zweck zu benutzen, zu dem es hergestellt

wurde. Der Hersteller haftet nicht für Schäden, die auf unsachgemäße Bedie-

nung des Geräts zurückzuführen sind.

• Den Kontakt des Gerätes und des Steckers mit Wasser oder einer anderen Flüs-

sigkeit vermeiden. Den Stecker unverzüglich aus dem Stecker ziehen und das

Gerät von einem anerkannten Fachmann prüfen lassen, wenn das Gerät unbeab-

sichtigterweise ins Wasser fällt. Bei Nichteinhaltung dieser Sicherheitsvorschrif-

ten besteht Lebensgefahr.

• Nie eigenständig das Gehäuse des Gerätes zu öffnen versuchen.

• In das Gehäuse des Gerätes keine Gegenstände einführen.

• Den Stecker nicht mit nassen oder feuchten Händen berühren.

• Gefahr eines Stromschlags! Das Gerät darf nicht selbstständig repariert wer-

den. Sämtliche Mängel und Unzulänglichkeiten sind ausschließlich durch quali-

ﬁ ziertes Personal zu beseitigen.

• Niemals ein beschädigtes Gerät benutzen! Das beschädigte Gerät vom Netz

trennen und sich mit dem Verkäufer in Verbindung setzen.

• Warnung: Die Elektroteile des Gerätes dürfen weder in Wasser noch in andere

Flüssigkeiten getaucht werden. Ebenso ist das Gerät nicht unter ﬂ ießendes Was-

ser zu halten.

• Der Stecker und die Stromversorgungsleitung sind regelmäßig auf Beschädigun-

gen zu prüfen. Der beschädigte Stecker oder Leitung sind an eine Servicestelle

oder einer anderen qualiﬁ zierten Person zur Reparatur zu übergeben, um even-

tuellen Gefahren und Verletzungen des Körpers vorzubeugen.

• Man muss sich davon überzeugen, ob die Stromversorgungsleitung weder mit

scharfkantigen noch mit heißen Gegenständen in Berührung kommt; halten Sie

die Leitung weit entfernt von einer offenen Flamme. Um den Stecker aus der

Netzsteckdose zu nehmen, muss man immer am Stecker und nicht an der Lei-

tung ziehen.

• Die Stromversorgungsleitung (oder Verlängerungsleitung) ist vor dem zufälli-

gen Herausziehen aus der Steckdose zu schützen. Die Stromversorgungsleitung

muss so geführt werden, dass niemand zufällig darüber stolpern kann.

• Das Gerät muss während seiner Anwendung ständig kontrolliert werden.

• Warnung! Wenn der Stecker in der Netzsteckdose ist, muss man das Gerät als

an die Stromversorgung angeschlossen betrachten.

• Bevor der Stecker aus der Netzsteckdose genommen wird, ist das Gerät

auszuschalten.

• Das Gerät darf beim Tragen nicht an der Leitung gehalten werden.

• Benutzen Sie kein Zubehör, das nicht mit diesem Gerät mitgeliefert wurde.

• Das Gerät muss man ausschließlich an die Steckdose mit solch einer Spannung

und Frequenz anschließen, wie auf dem Typenschild angegeben wird.

• Stecken Sie den Stecker in die Steckdose, die an einem leicht und bequem zu-

gänglichen Ort angeordnet ist, und zwar so, dass das Gerät bei einer Störung

sofort abgeschaltet werden kann. Um das Gerät vollständig auszuschalten, muss

man es von der Stromquelle trennen. Zu diesem Zweck muss man den Stecker,

der sich am Ende der vom Gerät getrennten Leitung beﬁ ndet, aus der Netzsteck-

dose ziehen.

• Vor dem Abtrennen des Steckers ist das Gerät auszuschalten!

• Benutzen Sie kein Zubehör, das nicht vom Hersteller empfohlen wird. Die Anwen-

dung vom nicht empfohlenen Zubehör stellt eine Gefahr für den Nutzer dar und

kann zur Beschädigung des Gerätes führen. Benutzen Sie ausschließlich Ersatz-

teile und Zubehör im Original.

• Dieses Gerät eignet sich nicht für den Gebrauch durch Personen (gilt auch für

Kinder) mit geringerer Motorik, Sensorik oder geistiger Fähigkeit oder mangel-

hafter Erfahrung und Wissen.

• Auf keinen Fall darf das Bedienen des Gerätes durch Kinder zugelassen werden.

• Das Gerät mit Stromversorgungsleitung ist außerhalb der Reichweite von Kin-

dern zu lagern.

• Ebenso muss dafür gesorgt werden, dass die Kinder das Gerät nicht zum Spielen

benutzen.

• Das Gerät ist immer dann von der Stromversorgung zu trennen, wenn es ohne

Aufsicht bleiben soll bzw. auch vor der Montage, Demontage und Reinigung.

• Während der Nutzung darf das Gerät nicht ohne Aufsicht gelassen werden.

3. ALLGEMEINE HINWEISE

Sehr wichtig: diese Anweisungen müssen für ein zukünftiges Nachschlagen zu-

sammen mit dem Gerät aufbewahrt werden.

Diese Hinweise wurden für Ihre Sicherheit und von Dritten verfasst. Wir bitten

Sie daher, sie vor Installation und Benutzung des Geräts aufmerksam zu lesen.

• Sollte die Verpackung bei Warenerhalt nicht unversehrt bzw. beschädigt sein, den

folgenden

Vorbehalt: “WARENKONTROLLE VORBEHALTEN”

mit Scha-

densbeschreibung anbringen und vom Frachtführer unterzeichnen lassen; beim

Verkäufer innerhalb von 4 Kalendertagen (keine Arbeitstage) ab Lieferdatum

eine schriftlich beanstanden; nach dieser Zeit werden keine Beanstandungen

akzeptiert.

• Die Temperatur innerhalb des Lager (oder anderer Raum) muss niemals unter

-9° C sein; sonst können die Kontrolle-Geräte (Thermostat/Sicherungsthermostat)

geschädigt werden. Falls dieser Hinweis nicht respektiert wird, werden jegliche

Verantwortung vom Hersteller abgelehnt.

• Das Gerät dient für professionellen Gebrauch und muss von zur Bedienung ge-

schultem Personal benutzt werden.

• Eventuelle Änderungen an der elektrischen Anlage,

für die Installati-

on des Geräts notwendig, dürfen nur durch Fachpersonal ausgeführt

werden.

• Es ist gefährlich, die Merkmale dieses Geräts zu ändern oder deren Änderung zu

versuchen.

• Das Gerät darf niemals mit direktem Wasserstrahl gereinigt werden, da eventuell

eindringendes Wasser seine Sicherheit einschränken könnte.

• Das Gerät vor Wartung oder Reinigung vom elektrischen Versorgungsnetz ab-

trennen und abkühlen lassen.

• Die Innenﬂ äche der ganz geöffneten Tür (ganz aufgeklappt) darf nicht als Ablage

benutzt werden, da sich die Türscharniere unreparierbar beschädigen könnten.

• Periodische Kontrollen oder eventuelle Reparaturen nicht selbst ausfüh-

ren. Wenden Sie sich an die naheste Kundendienststelle und benutzen Sie nur

Originalersatzteile.

N.B.: Jegliche Haftung der Herstellerﬁ rma verfällt infolge von unsachgemäßem

oder unkorrektem Gebrauch sowie der Nichtbeachtung der Installationsvorschrif-

ten. Diesbezüglich sind auch die Anweisungen in Par. ,,AUFSTELLEN” genauestens

zu befolgen.

4. TECHNISCHE MERKMALE

Abmessungen LxTxH (mm) 790x750x635

Gewicht (Kg) 50,4

Umluft-wiederstand (kW) 3,0

Max. Leistungsaufnahme (kW) 3,4

Versorgungsspannung (V) 230V ~50/60Hz

Querschnitt des Versorgungskabels 3x1,5 mm

Kabeltyp H07RN-F

Anschluss des Versorgungskabels Typ Y

Klasse I

Verkleidungsschutzgrad: IPX3

Wasserdruck (kPa) 100-200

Der Geräuschpegel des funktionierenden Geräts ist unter 70 dB (A).

Das Schild „ Technische Daten” beﬁndet sich auf der Geräterückseite.

Der Hersteller und Verkäufer tragen keine Ver-

antwortung für irgendwelche Unstimmigkeiten,

die sich aus den in der vorliegenden Anleitung

auftretenden Druckfehlern und Transkriptionen

ergeben. Gemäß unserer Politik in Bezug auf die

Weiterentwicklung der Produkte behalten wir

uns das Recht vor, die Änderungen an dem Pro-

dukt, der Verpackung und den in der Dokumenta-

tion enthaltenen Spezifikationen ohne Vorankün-

digung vorzunehmen.

5. ANWEISUNGEN FÜR DEN INSTALLATEUR

Die nachfolgenden Anweisungen wenden sich an

den Fachinstallateur, damit dieser Arbeiten wie

Installation, Einstellung und Wartung auf die kor-

rekteste Weise und nach den gültigen Vorschriften

ausführen kann. Arbeiten dürfen nur mit elektrisch

abgeschaltetem Gerät ausgeführt werden.

Vor der Benutzung des Geräts muss der spezielle

Klebeﬁ lm, der die Edelstahlteile schützt, entfernt

werden. Klebestoffreste sollten nicht auf den Ober-

ﬂ ächen bleiben, ggf. sofort mit einem geeigneten

Lösemittel entfernen.

Pagina se încarcă ...

Hendi 225516 Manual de utilizare

Marca: Hendi

Model: 225516

Categorie: Plite

Tip: Manual de utilizare

Descărcați PDF

raport

în alte limbi

français: Hendi 225516 Manuel utilisateur
polski: Hendi 225516 Instrukcja obsługi
Deutsch: Hendi 225516 Benutzerhandbuch
italiano: Hendi 225516 Manuale utente
Nederlands: Hendi 225516 Handleiding

Hendi 225516 Manual de utilizare

Hendi 225516 Manual de utilizare

în alte limbi

Lucrări conexe

Alte documente