Samsung HW-S40T Manual de utilizare

HW-S40T / S41T

FULL MANUAL

Imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please register

your product at www.samsung.com/register

ENG - 2

SAFETY INFORMATION

SAFETY WARNINGS

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE THE COVER (OR BACK).

NO USER-SERVICEABLE PARTS ARE INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

Refer to the table below for an explanation of

symbols which may be on your Samsung product.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

This symbol indicates that high voltage

is present inside. It is dangerous to

make any kind of contact with any

internal part of this product.

This symbol indicates that this product

has included important literature

concerning operation and maintenance.

Class II product : This symbol indicates

that it does not require a safety

connection to electrical earth (ground).

If this symbol is not present on a

product with a power cord, the product

MUST have a reliable connection to

protective earth (ground).

AC voltage : This symbol indicates that

the rated voltage marked with the

symbol is AC voltage.

DC voltage : This symbol indicates that

the rated voltage marked with the

symbol is DC voltage.

Caution, Consult instructions for use :

This symbol instructs the user to

consult the user manual for further

safety related information.

WARNING

• To reduce the risk of re or electric shock, do

not expose this appliance to rain or moisture.

CAUTION

• TO PREVENT ELECTRIC SHOCK, MATCH WIDE

BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

• This apparatus shall always be connected to a

AC outlet with a protective grounding

connection.

• To disconnect the apparatus from the mains,

the plug must be pulled out from the mains

socket, therefore the mains plug shall be

readily operable.

• Do not expose this apparatus to dripping or

splashing. Do not put objects lled with

liquids, such as vases on the apparatus.

• To turn this apparatus off completely, you

must pull the power plug out of the wall

socket. Consequently, the power plug must

be easily and readily accessible at all times.

ENG - 3

PRECAUTIONS

1. Ensure that the AC power supply in your

house complies with the power

requirements listed on the identication

sticker located on the bottom of your

product. Install your product horizontally, on

a suitable base (furniture), with enough

space around it for ventilation (7~10 cm).

Make sure the ventilation slots are not

covered. Do not place the unit on ampliers

or other equipment which may become hot.

This unit is designed for continuous use. To

fully turn off the unit, disconnect the AC plug

from the wall outlet. Unplug the unit if you

intend to leave it unused for a long period of

time.

2. During thunderstorms, disconnect the AC

plug from the wall outlet. Voltage peaks due

to lightning could damage the unit.

3. Do not expose the unit to direct sunlight or

other heat sources. This could lead to

overheating and cause the unit to

malfunction.

4. Protect the product from moisture (i.e.

vases), and excess heat (e.g. a replace) or

equipment creating strong magnetic or

electric elds. Unplug the power cable from

the AC wall socket if the unit malfunctions.

Your product is not intended for industrial

use. It is for personal use only. Condensation

may occur if your product has been stored in

cold temperatures. If transporting the unit

during the winter, wait approximately

2 hours until the unit has reached room

temperature before using.

5. The battery used with this product contains

chemicals that are harmful to the

environment. Do not dispose of the battery

in the general household trash. Do not

expose the battery to excess heat, direct

sunlight, or re. Do not short circuit,

disassemble, or overheat the battery.

Danger of explosion if the battery is replaced

incorrectly. Replace only with the same or

equivalent type.

ENG - 4

Fabric cleaning

Remove any dirt or stain on the product surface

immediately.

Removing and cleaning can be less effective for

some substances or if left for a prolonged time.

CAUTION

• Use a vacuum cleaner or an adhesive lint

roller to remove dust, handprints, and the

likes.

– Some cleaning brushes may damage the

product, depending on the materials they

contain.

– Towels and cleaning clothes may leave

lint or dirt on the product.

• Do not use a nail or other tools to scratch the

dirt off. It may damage the fabric.

• To remove oil or liquid stains, use a clean

white cloth moist with water. If the stain

persists, wipe it with a mixture of water and

neutral detergent (such as dishwashing

soaps) and a cloth.

– A non-neutral detergent or cleaner may

cause discolouration or fabric damage.

– After cleaning, use a dry cloth or

hairdryer to dry the area.

– Do not use excessive force to avoid

discolouration or fabric damage.

ENG - 5

CONTENTS

01 Checking the Components 7

Inserting Batteries before using the Remote Control (AA batteries X 2) ------------------------- 7

02 Product Overview 8

Top Panel of the Soundbar ------------------------- 8

Bottom Panel of the Soundbar ------------------------- 9

03 Using the Remote Control 10

How to Use the Remote Control

-------------------------

10

Adjusting the Soundbar volume with a TV remote control ------------------------- 13

04 Connecting the Soundbar 14

Connecting Electrical Power

-------------------------

14

05 Using a wired connection to the TV 15

Connecting using an Optical Cable

-------------------------

15

06 Using a wireless connection to the TV 16

Connecting via Bluetooth

-------------------------

16

07 Connecting an External Device 18

Connecting using an Optical Cable

-------------------------

18

ENG - 6

08 Connecting a Mobile Device 19

Connecting via Bluetooth

-------------------------

19

Using the Tap Sound

-------------------------

23

09 Installing on a wall 24

10 Installing the Soundbar in front of TV 24

11 Software Update 25

Initialization

-------------------------

26

12 Troubleshooting 27

13 Licence 28

14 Open Source Licence Notice 29

15 Important Notes About Service 29

16 SpecicationsandGuide 30

Specications

-------------------------

30

ENG - 7

01 CHECKING THE COMPONENTS

VOL WOOFER

SOUNDBAR

SOUND

MODE

PAIR

Soundbar Main Unit Soundbar Remote Control

/ Batteries

AC/DC Adapter

(Soundbar)

Power Cord

(Soundbar)

Optical Cable

• For more information about the power supply and power consumption, refer to the label attached

to the product. (Label: Bottom of the Soundbar Main Unit)

• To purchase additional components or optional cables, contact a Samsung Service Centre or

Samsung Customer Care.

• There are two wall mount holes (M4 size) at the bottom of the Soundbar. Individually purchase a

compatible bracket and mount the Soundbar on a wall to suit your preferences.

• Design, specications are subject to change without prior notice.

• The appearance of the accessories may differ slightly from the illustrations above.

Inserting Batteries before using the Remote Control (AA batteries X 2)

Slide the back cover in the direction of the arrow

until it is completely removed. Insert 2 AA batteries

(1.5V) oriented so that their polarity is correct. Slide

the back cover back into position.

ENG - 8

02 PRODUCT OVERVIEW

Top Panel of the Soundbar

Top Panel

Position the product so that

the SAMSUNG logo is

located on the top.

󰟶󰟴 󰟵

󰟳

LED

indicator

The LED Indicator ashes, glows, or changes colour depending on the Soundbar's current

mode or status. The colour of the LED indicator and the number of lights indicate the active

mode as described below.

W

White LED

W

White LED

M

Multicolour LED

W

White LED

W

White LED

• The Multicolour LED changes to White, Cyan, Green, Red, Yellow, Orange, Purple and

Blue depending on the mode or status.

󰟴

Power Turns the power on and off.

󰟵

Volume Adjusts the volume.

󰟶

Source

• Press the (Source) button to change the mode. Each time you change the mode,

the LED lights in white and then turns off.

LED Indicator

White On -> Off White On -> Off

“Digital Audio In” “Bluetooth”

• When you plug in the AC cord, the power button will begin working in 4 to 6 seconds.

• When you turn on this unit, there will be a 4 to 5 second delay before it produces sound.

• If you hear sounds from both the TV and Soundbar, go to the Settings menu for the TV audio and

change the TV speaker to External Speaker.

ENG - 9

Bottom Panel of the Soundbar

SERVICE

DC 24V

DIGITAL AUDIO IN

(OPTICAL)

DC 24V

SERVICE

DIGITAL AUDIO IN

(OPTICAL)

DC 24V

SERVICE

DIGITAL AUDIO IN

(OPTICAL)

SERVICE

DC 24V

DIGITAL AUDIO IN

(OPTICAL)

DC 24V

SERVICE

DIGITAL AUDIO IN

(OPTICAL)

DC 24V

SERVICE

DIGITAL AUDIO IN

(OPTICAL)

SERVICE

DC 24V

DIGITAL AUDIO IN

(OPTICAL)

DC 24V

SERVICE

DIGITAL AUDIO IN

(OPTICAL)

DC 24V

SERVICE

DIGITAL AUDIO IN

(OPTICAL)

󰟳 󰟴 󰟵

󰟳

DC 24V (Power Supply In)

Connect the AC/DC power adapter.

󰟴

DIGITAL AUDIO IN (OPTICAL)

Connect to the digital (optical) output of an external device.

󰟵

SERVICE

Connect a USB storage device to upgrade the product's software.

• When disconnecting the power cable of the AC/DC power adaptor from a wall outlet, pull the plug.

Do not pull the cable.

• Do not connect this unit or other components to an AC outlet until all connections between

components are complete.

ENG - 10

03 USING THE REMOTE CONTROL

How to Use the Remote Control

VOL WOOFER

SOUNDBAR

SOUND

MODE

PAIR

󰟳

󰟴

󰟵

󰟶

󰟷

󰟹

󰟸

󰟺

󰟼

󰟻

󰟳

Power

Turns the Soundbar on and off.

LED

Indicator

Cyan Blinks X1

On

Off

Red Blinks X3

• Auto Power Down Function

The unit turns off automatically in the following

situations:

– In “Digital Audio In” / “Bluetooth” mode if there is no

audio signal for 20 minutes.

󰟴

(Source)

Press to select a source connected to the Soundbar.

󰟵

(Mute)

Press the (Mute) button to mute the sound.

Press it again to unmute the sound.

LED

Indicator

Blinks X Repeatly

ENG - 11

󰟶

SOUND MODE

By pressing the button, you can select the desired audio mode. Each time the mode changes, the

Multicolour LED blinks in white.

LED

Indicator

White Blinks X1

“Standard”  “Smart”  “Music”

• Standard

Outputs the original sound.

• Smart

Analyzes the content in real time and automatically provides the optimal sound eld based on the

characteristics of the content.

• Music

Provides more natural and room lling sound for music content.

󰟷

Bluetooth PAIR

Switch the Soundbar to Bluetooth pairing mode.

When you press the button, the LED display changes as shown below.

• Until pairing is complete, the Multicolour LED changes as Red → Green → Blue in turn.

LED

Indicator

Red → Green → Blue Blinks

Pairing

Connection is complete

Cyan Blinks X3

󰟸

p (Play / Pause)

You can also play or pause music by pressing the button.

󰟹

Up/Down/Left/Right

Press Up/Down/Left/Right on the button to select or set functions.

• Music Skip

Press the Right button to select the next music le. Press the Left button to select the previous

music le.

ENG - 12

󰟺

(Sound Control)

By pressing the button, you can select the desired audio mode. The desired item can be adjusted using

the Up/Down buttons. Each time the mode changes, the Multicolour LED blinks in white.

LED

Indicator

White Blinks X1

“Treble”  “Bass”  “Sync”

󰟻

WOOFER (BASS) LEVEL

Push the button up or down to adjust the woofer (bass) between -6 to +6. To set the woofer (bass)

volume level to 0 (Default), press the button.

󰟼

VOLUME

Push the button up or down to adjust the volume.

LED

Indicator

White moves to right X1

Volume Up

White moves to left X1

Volume Down

ENG - 13

Adjusting the Soundbar volume with a TV remote control

Adjust the Soundbar volume using the TV’s remote control.

• This function can be used with IR remote controls only. Bluetooth remote controls (remote

controls that require pairing) are not supported.

• Set the TV speaker to External Speaker to use this function.

• Manufacturers supporting this function:

VIZIO, LG, Sony, Sharp, PHILIPS, PANASONIC, TOSHIBA, Hisense, RCA

1. Turn Off the Soundbar.

2. Push up and hold the WOOFER button for 5 seconds.

Each time you push the WOOFER button up and hold it for 5 seconds, the mode switches in the

following order: “Samsung-TV Remote” (Default mode), “Off-TV Remote”, “All-TV Remote”.

The LED indicator status changes each time the mode is changed, as shown below.

Remote Control Button LED Indicator Status

SOUND

MODE

VOL

WOOFER

SOUNDBAR

5 Sec

"Samsung-TV Remote"

(Default mode)

Blue Blinks X1

Enable a Samsung TV’s IR remote

control.

SOUND

MODE

VOL

WOOFER

SOUNDBAR

5 Sec

"Off-TV Remote"

Red Blinks X1

Disable the TV remote control.

SOUND

MODE

VOL

WOOFER

SOUNDBAR

5 Sec

"All-TV Remote"

Green Blinks X1

Enable a third-party TV’s IR remote

control.

ENG - 14

04 CONNECTING THE SOUNDBAR

Connecting Electrical Power

Use the power components to connect the Soundbar to an electrical outlet in the following order:

• For more information about the required electrical power and power consumption, refer to the

label attached to the product. (Label: Bottom of the Soundbar Main Unit)

1. First connect the power cable to the AC/DC adapter.

Connect the AC/DC adapter (with the power cable) to the Soundbar.

2. Connect the power cord to a wall socket.

DC 19V

Power Cord

AC/DC Adapter

SERVICE

DC 24V

DIGITAL AUDIO IN

(OPTICAL)

DC 24V

SERVICE

DIGITAL AUDIO IN

(OPTICAL)

DC 24V

SERVICE

DIGITAL AUDIO IN

(OPTICAL)

SERVICE

DC 24V

DIGITAL AUDIO IN

(OPTICAL)

DC 24V

SERVICE

DIGITAL AUDIO IN

(OPTICAL)

DC 24V

SERVICE

DIGITAL AUDIO IN

(OPTICAL)

DC 19V

Bottom of the Soundbar Main Unit

NOTES

• If you unplug and reconnect the power cord when the product is turned on, the Soundbar turns on

automatically.

• Make sure to rest the AC/DC Adapter at on a table or the oor. If you place the AC/DC Adapter so

that it is hanging with the AC cord input facing upwards, water or other foreign substances could

enter the Adapter and cause the Adapter to malfunction.

ENG - 15

05 USING A WIRED CONNECTION TO THE TV

Connecting using an Optical Cable

When the audio in a broadcast is encoded in Dolby Digital and the “Digital Output Audio Format” on

your TV is set to PCM, we recommend that you change the setting to Dolby Digital. When the setting on

the TV is changed, you will experience better sound quality. (The TV menu may use different words for

Dolby Digital and PCM depending on the TV manufacturer.)

Pre-connection Checklist

• When you use an optical cable and the terminals have covers, be sure to remove the covers.

LED

Indicator

White On -> Off

“Digital Audio In”

DC 24V

SERVICE

DIGITAL AUDIO IN

(OPTICAL)

OPTICAL OUT

Bottom of the Soundbar

Optical Cable

Top of the Soundbar

1. With the TV and Soundbar turned off, connect the DIGITAL AUDIO IN (OPTICAL) port on the

Soundbar and the OPTICAL output port on the TV with the optical cable, as shown in the gure.

2. Turn on the Soundbar and TV.

3. Press the (Source) button on the top panel or remote control, and then select the “Digital

Audio In” mode.

4. The TV sound is output from the Soundbar.

ENG - 16

06 USING A WIRELESS CONNECTION TO THE TV

Connecting via Bluetooth

When a Samsung TV is connected using Bluetooth, you can hear stereo sound

without the hassle of cables.

• Only one Samsung TV can be connected at a time.

• Samsung TV that supports Bluetooth can be connected.

Check the specications of your TV.

The initial connection

1.

Bluetooth Pairing button LED Indicator

SOUND

MODE

PAIR

OR

Red → Green → Blue Blinks

Pairing

Connection is complete

Cyan Blinks X3

When in “Bluetooth” mode

5 Sec

• Until pairing is complete, the Multicolor LED changes as Red → Green

→ Blue in turn.

“Ready to connect via

Bluetooth.”

“Ding” Short Sound.

2. Select Bluetooth mode on the Samsung TV.

(e.g. Home ( )  Settings ( )  Sound  Sound Output  Bluetooth Speaker List 

[AV] Samsung Soundbar S4T-Series (Bluetooth))

3. Select “[AV] Samsung Soundbar S4T-Series” from the list on TV’s screen.

An available Soundbar is indicated with “Need Pairing” or “Paired” on the TV’s Bluetooth device

list. To connect the Samsung TV to the Soundbar, select the message, and then establish a

connection.

4. You can now hear Samsung TV sound from the Soundbar.

• If there is a connection log between the Soundbar and Samsung TV, the Soundbar is

automatically connected by changing its mode to “Bluetooth”.

ENG - 17

If the device fails to connect

• If you have an existing Soundbar (e.g., [AV] Samsung Soundbar S4T-Series) on the list of

speakers on the Samsung TV, delete it.

• Then repeat steps 1 through 3.

Disconnecting the Soundbar from the Samsung TV

Press the (Source)

button on the top panel or on the remote control to select the mode other than

“Bluetooth”.

• Disconnecting takes time because the Samsung TV must receive a response from the Soundbar.

(The time required may differ, depending on the Samsung TV model.)

Notes on Bluetooth connection

• Locate a new device within 1 m to connect via Bluetooth communication.

• If asked for a PIN code when connecting a Bluetooth device, enter <0000>.

• The Soundbar automatically turns off after 20 minutes in the Ready state.

• The Soundbar may not perform Bluetooth search or connection correctly under the following

circumstances:

– If there is a strong electrical eld around the Soundbar.

– If several Bluetooth devices are simultaneously paired with the Soundbar.

– If the Bluetooth device is turned off, not in place, or malfunctions.

• Electronic devices may cause radio interference. Devices that generate electromagnetic waves

must be kept away from the Soundbar main unit - e.g., microwaves, wireless LAN devices, etc.

ENG - 18

07 CONNECTING AN EXTERNAL DEVICE

Connecting using an Optical Cable

LED

Indicator

White On -> Off

“Digital Audio In”

DC 24V

SERVICE

DIGITAL AUDIO IN

(OPTICAL)

- AUDIO -

R L

OPTICAL OUT

Bottom of the Soundbar

Optical Cable

Top of the Soundbar

BD / DVD player / Set-top

box / Game console

1. With the external device and Soundbar turned off, connect the DIGITAL AUDIO IN (OPTICAL) port

on the Soundbar and the OPTICAL output port on the external device with the optical cable, as

shown in the gure.

2. Turn on the Soundbar and external device.

3. Press the (Source) button on the top panel or remote control, and then select the “Digital

Audio In” mode.

4. The external device sound is output from the Soundbar.

ENG - 19

08 CONNECTING A MOBILE DEVICE

Connecting via Bluetooth

When a mobile device is connected using Bluetooth, you can hear stereo sound

without the hassle of cables.

• When you connect a paired Bluetooth device with the Soundbar off, the

Soundbar automatically turns on.

The initial connection

• When connecting to a new Bluetooth device, make sure the device is within 1 m distance.

1.

Bluetooth Pairing button LED Indicator

SOUND

MODE

PAIR

OR

Red → Green → Blue Blinks

Pairing

Connection is complete

Cyan Blinks X3

When in “Bluetooth” mode

5 Sec

• Until pairing is complete, the Multicolor LED changes as Red → Green

→ Blue in turn.

“Ready to connect via

Bluetooth.”

“Ding” Short Sound.

2. On your device, select “[AV] Samsung Soundbar S4T-Series” from the list that appears.

3. Play music les from the device connected via Bluetooth through the Soundbar.

If the device fails to connect

• If you have an existing Soundbar (e.g., [AV] Samsung Soundbar S4T-Series) on the list of

speakers on the Mobile device, delete it.

• Then repeat steps 1 and 2.

mobile device

ENG - 20

Notes on Bluetooth connection

• Locate a new device within 1 m to connect via Bluetooth communication.

• If asked for a PIN code when connecting a Bluetooth device, enter <0000>.

• The Soundbar automatically turns off after 20 minutes in the Ready state.

• The Soundbar may not perform Bluetooth search or connection correctly under the following

circumstances:

– If there is a strong electrical eld around the Soundbar.

– If several Bluetooth devices are simultaneously paired with the Soundbar.

– If the Bluetooth device is turned off, not in place, or malfunctions.

• Electronic devices may cause radio interference. Devices that generate electromagnetic waves

must be kept away from the Soundbar main unit - e.g., microwaves, wireless LAN devices, etc.

• The Soundbar supports SBC data (44.1kHz, 48kHz).

• Connect only to a Bluetooth device that supports the A2DP (AV) function.

• You cannot connect the Soundbar to a Bluetooth device that supports only the HF (Hands Free)

function.

• When connecting the Soundbar to a Bluetooth device, place them as close to each other as possible.

• The farther the Soundbar and Bluetooth device are from each other, the lower the sound quality

will become.

The Bluetooth connection may break when the devices are out of the effective range.

• The Bluetooth connection may not function as intended in areas with poor reception.

• A Bluetooth device may experience noise or malfunction under in the following conditions:

– When the body is in contact with the signal transceiver on the Bluetooth device or Soundbar

– In corners or when there is an obstacle in proximity, such as a wall or partition, where electrical

changes may occur.

– When exposed to radio interferences by other products operating on the same frequency

ranges, such as medical equipment, microwave ovens, and wireless LAN devices.

– Obstacles such as doors and walls may still impact the sound quality even when the devices

are within the effective range.

• Note that your Soundbar cannot be paired with other Bluetooth devices while using the Bluetooth

option.

• This wireless device may cause electrical interference during operation.

Pagina se încarcă ...

Samsung HW-S40T Manual de utilizare

Acest manual este potrivit și pentru

Samsung HW-S40T Manual de utilizare

în alte limbi

Lucrări conexe

Alte documente