Ubiquiti airVision-C Ghid de inițiere rapidă

Marca: Ubiquiti

Model: airVision-C

Tip: Ghid de inițiere rapidă

Network Video Recorder

Model: airVision-C

Introduction

Thank you for purchasing the Ubiquiti Networks

™

airVision

™

NVR,

model airVision-C. This Quick Start Guide is designed to guide you

through the installation of the airVisionNVR and show you how

to configure airVision Controller using the airVision Setup Wizard.

This Quick Start Guide also includes the warranty terms.

Package Contents

airVision NVR Vertical Support Stand

Power Adapter

(19V, 3.42A)

Power Cord

Network Video Recorder

Model: airVision-C

Magnetic Rubber Feet

(Qty. 4)

Quick Start Guide

follow local country regulations, including operation within legal frequency channels, output power,

indoor cabling requirements, and Dynamic Frequency Selection (DFS) requirements.

airVision

™

NVR Quick Start Guide

Hardware Overview

Back Panel

10/100/1000

Ethernet

Not used

Power

Not used by airVision

Front Panel

Reset Button

Power Button

Not used by airVision

Interface Description

Power Button

Powers ON or OFF the airVision NVR

• Power ON Press the Power button to turn on the

airVision NVR and start all services.

• Soft Power OFF Briefly press the Power button

to stop all services and safely shut down the

airVision NVR.

• Hard Power OFF Press and hold the Power

button to immediately turn off the airVision NVR.

Reset Button

Resets the airVision NVR to factory defaults. The

airVision NVR must be fully booted and running.

Press and hold the Reset button for about 10

seconds. The airVision NVR will automatically reboot

with default settings.

WARNING: Resetting the airVision NVR erases all recordings and

configuration settings.

Hardware Overview

Hardware Installation

The small form factor of the airVision NVR allows it to be placed

vertically or horizontally on any flat surface.

Vertical Placement

Place the airVision NVR in the narrow opening of the Vertical

Support Stand.

airVision

™

NVR Quick Start Guide

Horizontal Placement

Place the four Magnetic Rubber Feet on the bottom of the

airVisionNVR case.

Connecting the airVision NVR

1. Connect an Ethernet cable from your LAN to the Ethernet port.

2. Connect the Power Adapter to the Power port.

airVision

™

NVR Quick Start Guide

3. Connect the Power Cord to the Power Adapter. Connect the

other end of the Power Cord to a power outlet.

Accessing the airVision Configuration Portal

The airVision Configuration Portal is accessed by using a web

browser. There are three different ways to access the portal:

• airVision Online Registration The simplest method for airVision

NVRs connected to a DHCP-enabled LAN with Internet access.

• Ubiquiti Device Discovery Tool For users with a DHCP-enabled

LAN that do not wish to register or do not have Internet access.

• Direct Connection to airVision NVR Allows you to configure

the airVision NVR by connecting it directly to your computer via

Ethernet.

airVision Online Registration

Note: The airVision NVR must be connected to a

DHCP-enabled LAN that has Internet access.

1. Press the Power button on the airVision NVR, and wait about

one minute for it to fully boot up and start all services.

2. Launch a web browser from a computer connected to the

same LAN. Type http://www.ubnt.com/airvision/register in

the address field. Press enter (PC) or return (Mac).

Accessing the airVision Configuration Portal

3. After registering the airVision NVR, the web browser will be

automatically redirected to the Configuration Portal.

4. Go to Configuring the airVision Controller on page 9.

Ubiquiti Device Discovery Tool

If it is not already installed, download the Ubiquiti Device

Discovery Tool (v2.3.1) at www.ubnt.com/download#app

1. Press the Power button on the airVision NVR, and wait about

one minute for it to fully boot up and start all services.

2. Launch the Ubiquiti Device Discovery Tool.

3. A list of Ubiquiti devices on the network will appear. Locate

airVision NVR under Product Name and double-click it.

4. Click Web UI on the right.

5. Go to Configuring the airVision Controller on page 9.

airVision

™

NVR Quick Start Guide

Direct Connection to airVision NVR

1. Connect the Ethernet cable from the airVision NVR directly to

your computer.

2. Press the Power button on the airVision NVR, and wait about

one minute for it to fully boot up and start all services.

3. Configure the Ethernet adapter on your computer with a static

IP address on the 192.168.1.x subnet.

4. Launch a web browser and type http:// 192.168.1.30 in the

address field. Press enter (PC) or return (Mac).

Accessing the airVision Configuration Portal

Configuring the airVision Controller

1. The airVision Configuration Portal will appear in your browser.

Click airVision Controller.

Note: Advanced configuration options, such as network

settings, may be accessed in Device Configuration.

2. The airVision Setup Wizard will appear:

a. Enter a system name for the NVR.

b. Select your preferred language.

c. Specify your time zone.

d. Click Next.

airVision

™

NVR Quick Start Guide

3. Enter an administrator email address, name, and password to

use when accessing the airVision Controller Interface. Confirm

your password. Click Next.

4. Choose one of the following:

• To set up this

airVision NVR as a new airVision Controller,

select Create a new Controller. Click Next.

• To link this

airVision NVR to an existing airVision Controller,

click Detect Controllers and select the Controller from the

drop-down list. Click Next.

Accessing the airVision Configuration Portal

5. Select your desired management settings. To enable automatic

airCam management, enter the airCam login username and

password. Click Next.

6. Review your settings. Click Finish to save your settings, or click

Back to make changes. When finished, the airVision Controller

Interface will launch.

airVision

™

NVR Quick Start Guide

7. A login screen will appear for the airVision Controller Interface.

Enter the email address and password that you created, and

click Login.

For detailed information on using airVision software, download

the airVision User Guide at documentation.ubnt.com/airvision

Specifications

airVision NVR

Dimensions 135 x 190 x 25 mm

Weight 483 g

Processor Intel D2550

Memory 4 GB

Hard Drive Capacity 500 GB

Networking Interface (1) 10/100/1000 Ethernet Port

Power Supply 65W, 19V, 3.42A

Certications CE, IC

Safety Notices

1. Read, follow, and keep these instructions.

2. Heed all warnings.

3. Only use attachments/accessories specified by the manufacturer.

WARNING: Do not use this product in location that can be

submerged by water.

WARNING: Avoid using this product during an electrical storm.

There may be a remote risk of electric shock from lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current

requirements indicated on the manufacturer’s label. Connection to a

different power source than those specified may result in improper

operation, damage to the equipment or pose a fire hazard if the limitations

are not followed.

2. There are no operator serviceable parts inside this equipment. Service

should be provided only by a qualified service technician.

3. This equipment is provided with a detachable power cord which has an

integral safety ground wire intended for connection to a grounded safety

outlet.

a. Do not substitute the power cord with one that is not the provided

approved type. Never use an adapter plug to connect to a 2-wire

outlet as this will defeat the continuity of the grounding wire.

b. The equipment requires the use of the ground wire as a part of the

safety certification, modification or misuse can provide a shock

hazard that can result in serious injury or death.

c. Contact a qualified electrician or the manufacturer if there are

questions about the installation prior to connecting the equipment.

d. Protective earthing is provided by Listed AC adapter. Building

installation shall provide appropriate short-circuit backup

protection.

e. Protective bonding must be installed in accordance with local

national wiring rules and regulations.

airVision

™

NVR Quick Start Guide

Limited Warranty

UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the product(s)

furnished hereunder (the “Product(s)”) shall be free from defects in material

and workmanship for a period of one (1) year from the date of shipment by

UBIQUITI NETWORKS under normal use and operation. UBIQUITI NETWORKS’

sole and exclusive obligation and liability under the foregoing warranty shall

be for UBIQUITI NETWORKS, at its discretion, to repair or replace any Product

that fails to conform to the above warranty during the above warranty period.

The expense of removal and reinstallation of any Product is not included in this

warranty. The warranty period of any repaired or replaced Product shall not

extend beyond its original term.

Warranty Conditions

The above warranty does not apply if the Product:

(I) has been modified and/or altered, or an addition made thereto, except by

Ubiquiti Networks, or Ubiquiti Networks’ authorized representatives, or as

approved by Ubiquiti Networks in writing;

(II) has been painted, rebranded or physically modified in any way;

(III) has been damaged due to errors or defects in cabling;

(IV) has been subjected to misuse, abuse, negligence, abnormal physical,

electromagnetic or electrical stress, including lightning strikes, or

accident;

(V) has been damaged or impaired as a result of using third party firmware; or

(VI) has no original Ubiquiti MAC label, or is missing any other original Ubiquiti

label(s).

In addition, the above warranty shall apply only if: the product has been

properly installed and used at all times in accordance, and in all material

respects, with the applicable Product documentation; all Ethernet cabling runs

use CAT5 (or above), and for outdoor installations, shielded Ethernet cabling is

used, and for indoor installations, indoor cabling requirements are followed.

Returns

No Products will be accepted for replacement or repair without obtaining a

Return Materials Authorization (RMA) number from UBIQUITI NETWORKS during

the warranty period, and the Products being received at UBIQUITI NETWORKS’

facility freight prepaid in accordance with the RMA process of UBIQUITI

NETWORKS. Products returned without an RMA number will not be processed

and will be returned freight collect or subject to disposal. Information on the

RMA process and obtaining an RMA number can be found at:

www.ubnt.com/support/warranty.

Limited Warranty

Disclaimer

EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI

NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA, SERVICE,

SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM AND MAKE NO

OTHER REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESS, IMPLIED

OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, REPRESENTATIONS,

GUARANTEES, OR WARRANTIES OF MERCHANTABILITY, ACCURACY, QUALITY

OF SERVICE OR RESULTS, AVAILABILITY, SATISFACTORY QUALITY, LACK OF

VIRUSES, QUIET ENJOYMENT, FITNESS FOR A PARTICULAR PURPOSE AND

NON-INFRINGEMENT AND ANY WARRANTIES ARISING FROM ANY COURSE

OF DEALING, USAGE OR TRADE PRACTICE IN CONNECTION WITH SUCH

PRODUCTS AND SERVICES. BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI

NETWORKS NOR ITS THIRD PARTY PROVIDERS CONTROL BUYER’S EQUIPMENT

OR THE TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING

THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE SUBJECT

TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS AND OTHER

PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS FACILITIES. UBIQUITI

NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD PARTY PROVIDERS

ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS, DELAYS, CANCELLATIONS,

DELIVERY FAILURES, DATA LOSS, CONTENT CORRUPTION, PACKET LOSS, OR

OTHER DAMAGE RESULTING FROM ANY OF THE FOREGOING. In addition,

UBIQUITI NETWORKS does not warrant that the operation of the Products

will be error-free or that operation will be uninterrupted. In no event shall

UBIQUITI NETWORKS be responsible for damages or claims of any nature

or description relating to system performance, including coverage, buyer’s

selection of products (including the Products) for buyer’s application and/or

failure of products (including the Products) to meet government or regulatory

requirements.

Limitation of Liability

EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL

UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR DIRECT,

SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES (INCLUDING

LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING OUT OF THE USE,

INABILITY TO USE, OR THE RESULTS OF USE OF THE PRODUCT, WHETHER BASED

IN WARRANTY, CONTRACT, TORT OR OTHER LEGAL THEORY, AND WHETHER OR

NOT ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Note

Some countries, states and provinces do not allow exclusions of implied

warranties or conditions, so the above exclusion may not apply to you. You may

have other rights that vary from country to country, state to state, or province

to province. Some countries, states and provinces do not allow the exclusion

or limitation of liability for incidental or consequential damages, so the above

limitation may not apply to you. EXCEPT TO THE EXTENT ALLOWED BY LOCAL

LAW, THESE WARRANTY TERMS DO NOT EXCLUDE, RESTRICT OR MODIFY, AND

ARE IN ADDITION TO, THE MANDATORY STATUTORY RIGHTS APPLICABLE TO THE

LICENSE OF ANY SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United

Nations Convention on Contracts for the International Sale of Goods shall not

apply to any transactions regarding the sale of the Products.

airVision

™

NVR Quick Start Guide

Compliance

FCC

Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference

that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits

for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operations of this equipment in a

residential area is likely to cause harmful interference in which case the user will

be required to correct the interference at his own expense.

For MPE and antenna usage details, please visit our website at

www.ubnt.com/products

Industry Canada

This Class A digital apparatus complies with Canadian ICES-003.

To reduce potential radio interference to other users, the antenna type and

its gain should be so chosen that the equivalent isotropically radiated power

(e.i.r.p.) is not more than that permitted for successful communication.

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference that may

cause undesired operation of the device.

Cet appareil numérique de la classe A est conforme à la norme NMB-003

Canada.

Pour réduire le risque d’interférence aux autres utilisateurs, le type d’antenne

et son gain doivent être choisies de façon que la puissance isotrope

rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessaire pour une

communication réussie.

Cet appareil est conforme à la norme RSS Industrie Canada exempts de licence

norme(s). Son fonctionnement est soumis aux deux conditions suivantes:

1. Cet appareil ne peut pas provoquer d’interférences et

2. Cet appareil doit accepter toute interférence, y compris les interférences

qui peuvent causer un mauvais fonctionnement du dispositif.

Compliance

CE Marking

CE marking on this product represents the product is in compliance with all

directives that are applicable to it.

RoHS/WEEE Compliance Statement

English

European Directive 2002/96/EC requires that the equipment bearing this

symbol on the product and/or its packaging must not be disposed of with

unsorted municipal waste. The symbol indicates that this product should

be disposed of separately from regular household waste streams. It is your

responsibility to dispose of this and other electric and electronic equipment

via designated collection facilities appointed by the government or local

authorities. Correct disposal and recycling will help prevent potential negative

consequences to the environment and human health. For more detailed

information about the disposal of your old equipment, please contact your

local authorities, waste disposal service, or the shop where you purchased the

product.

Deutsch

Die Europäische Richtlinie 2002/96/EC verlangt, dass technische Ausrüstung,

die direkt am Gerät und/oder an der Verpackung mit diesem Symbol

versehen ist, nicht zusammen mit unsortiertem Gemeindeabfall entsorgt

werden darf. Das Symbol weist darauf hin, dass das Produkt von regulärem

Haushaltmüll getrennt entsorgt werden sollte. Es liegt in Ihrer Verantwortung,

dieses Gerät und andere elektrische und elektronische Geräte über die dafür

zuständigen und von der Regierung oder örtlichen Behörden dazu bestimmten

Sammelstellen zu entsorgen. Ordnungsgemäßes Entsorgen und Recyceln

trägt dazu bei, potentielle negative Folgen für Umwelt und die menschliche

Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung

Ihrer Altgeräte benötigen, wenden Sie sich bitte an die örtlichen Behörden oder

städtischen Entsorgungsdienste oder an den Händler, bei dem Sie das Produkt

erworben haben.

airVision

™

NVR Quick Start Guide

Español

La Directiva 2002/96/CE de la UE exige que los equipos que lleven este símbolo

en el propio aparato y/o en su embalaje no deben eliminarse junto con otros

residuos urbanos no seleccionados. El símbolo indica que el producto en

cuestión debe separarse de los residuos domésticos convencionales con

vistas a su eliminación. Es responsabilidad suya desechar este y cualesquiera

otros aparatos eléctricos y electrónicos a través de los puntos de recogida que

ponen a su disposición el gobierno y las autoridades locales. Al desechar y

reciclar correctamente estos aparatos estará contribuyendo a evitar posibles

consecuencias negativas para el medio ambiente y la salud de las personas.

Si desea obtener información más detallada sobre la eliminación segura de

su aparato usado, consulte a las autoridades locales, al servicio de recogida y

eliminación de residuos de su zona o pregunte en la tienda donde adquirió el

producto.

Français

La directive européenne 2002/96/CE exige que l’équipement sur lequel est

apposé ce symbole sur le produit et/ou son emballage ne soit pas jeté avec les

autres ordures ménagères. Ce symbole indique que le produit doit être éliminé

dans un circuit distinct de celui pour les déchets des ménages. Il est de votre

responsabilité de jeter ce matériel ainsi que tout autre matériel électrique ou

électronique par les moyens de collecte indiqués par le gouvernement et les

pouvoirs publics des collectivités territoriales. L’élimination et le recyclage en

bonne et due forme ont pour but de lutter contre l’impact néfaste potentiel

de ce type de produits sur l’environnement et la santé publique. Pour plus

d’informations sur le mode d’élimination de votre ancien équipement, veuillez

prendre contact avec les pouvoirs publics locaux, le service de traitement des

déchets, ou l’endroit où vous avez acheté le produit.

Italiano

La direttiva europea 2002/96/EC richiede che le apparecchiature contrassegnate

con questo simbolo sul prodotto e/o sull’imballaggio non siano smaltite

insieme ai rifiuti urbani non differenziati. Il simbolo indica che questo prodotto

non deve essere smaltito insieme ai normali rifiuti domestici. È responsabilità

del proprietario smaltire sia questi prodotti sia le altre apparecchiature

elettriche ed elettroniche mediante le specifiche strutture di raccolta indicate

dal governo o dagli enti pubblici locali. Il corretto smaltimento ed il riciclaggio

aiuteranno a prevenire conseguenze potenzialmente negative per l’ambiente

e per la salute dell’essere umano. Per ricevere informazioni più dettagliate circa

lo smaltimento delle vecchie apparecchiature in Vostro possesso, Vi invitiamo

a contattare gli enti pubblici di competenza, il servizio di smaltimento rifiuti o il

negozio nel quale avete acquistato il prodotto.

Pagina se încarcă ...

Ubiquiti airVision-C Ghid de inițiere rapidă

Marca: Ubiquiti

Model: airVision-C

Tip: Ghid de inițiere rapidă

Descărcați PDF

raport

în alte limbi

English: Ubiquiti airVision-C Quick start guide
italiano: Ubiquiti airVision-C Guida Rapida

Ubiquiti airVision-C Ghid de inițiere rapidă

Ubiquiti airVision-C Ghid de inițiere rapidă

în alte limbi

Lucrări conexe

Alte documente