KYLAND Technology SICOM3000 Hardware Installation Manual

SICOM3000 Industrial Ethernet Switch

Hardware Installation Manual

Publication Data: Jun. 2013

Version: V1.0

No.: 1.12.02.-0

SICOM3000 Industrial Ethernet Switch

Hardware Installation Manual

Disclaimer:

Kyland Technology Co., Ltd. tries to keep the content

of this manual as accurate and as updated as possible. This

document is not guaranteed to be error-free, and we reserve the

right to amend it without notice to users.

No part of this documentation may be excerpted, reproduced,

translated, annotated or duplicated, in any form or by any means

without the prior written permission of KYLAND Corporation.

Notice for Safety Operation

The product performs reliably as long as it is used accord-

ing to the guidance. Artificial damage or destruction of the

device should be avoided. Before using the device, read

this notice carefully for personal and equipment safety.

Please keep the manual for further reference. Kyland is

not liable to any personal or equipment damage caused

by violation of this notice.

●

Do not place the device near water sources or damp areas. Keep

the ambient relative humidity within the range from 5% to 95%

(non-condensing).

●

Do not place the device in an environment with high magnetic field,

strong shock, or high temperature. Keep the working and storage

temperatures within the allowed range.

●

Install and place the device securely and firmly.

●

Please keep the device clean; if necessary, wipe it with a soft cotton

cloth.

●

Do not place any irrelevant materials on the device or cables. Ensure

adequate heat dissipation and tidy cable layout without knots.

●

Wear antistatic gloves or take other protective measures when

operating the device.

●

Avoid any exposed metal wires because they may be oxidized

or electrified.

●

Install the device in accordance with related national and local

regulations.

●

Before power-on, make sure the power supply is within the allowed

range of the device. High voltage may damage the device.

●

Power connectors and other connectors should be firmly interconnected.

●

Do not plug in or out the power supply with wet hands. When the device

is powered on, do not touch the device or any parts with wet hands.

●

Before operating a device connected to a power cable, remove all

jewelry (such as rings, bracelets, watches, and necklaces) or any

other metal objects, because they may cause electric shock or burns.

●

Do not operate the device or connect or disconnect cables during

an electrical storm.

●

Use compatible connectors and cables. If you are not sure, contact

our sales or technical support personnel for confirmation.

●

Do not disassemble the device by yourself. When an anomaly

occurs, contact our sales or technical support personnel.

●

If any part is lost, contact our sales or technical support personnel

to purchase the substitute. Do not purchase parts from other channels.

●

Dispose of the device in accordance with relevant national provisions,

preventing environmental pollution.

In the following cases, please immediately shut down

your power supply and contact your Kyland represen-

tative:

●

Water gets into the equipment.

●

Equipment damage or shell damage.

●

Equipment operation or performance has abnormally changed.

●

The equipment emits odor, smoke or abnormal noise.

1 Product OverviewĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂ Ă Ă 1

2 Structure and InterfaceĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂ 2

2.1 Front PanelĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂ 2

2.2 Top PanelĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂ 6

3 MountingĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂ 7

3.1 Dimension Drawing

ĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂ

7

3.2 Mounting Modes and Steps

ĂĂĂĂĂĂĂĂĂĂĂĂĂ

8

3.2.1 Mounting

ĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂ

8

3.2.2 Panel Mounting

ĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂ

10

4 Connection

ĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂ

12

4.1 10/100Base-T(X) Ethernet Port

ĂĂĂĂĂĂĂĂĂĂĂĂ

12

4.2 100Base-FX Ethernet Port

ĂĂĂĂĂĂĂĂĂĂĂĂĂĂ

14

4.3 1000Base-X, 10/100/1000Base-T(X) SFP Slot

ĂĂĂĂĂ

15

4.3.1 Gigabit SFP Optical ModuleĂĂĂĂĂĂĂĂĂĂĂ

16

4.3.2 Gigabit SFP Electrical ModuleĂĂĂĂĂĂĂĂĂĂ

18

4.4 Console Port

ĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂ

19

4.5 Grounding

ĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂ

20

4.6 Power Terminal Block

ĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂ

21

4.7 Alarm Terminal Block

ĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂ

24

5 LEDs

ĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂ

26

6 Switch Access

ĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂ

27

6.1 Access through Console Port

ĂĂĂĂĂĂĂĂĂĂĂĂĂ

27

6.2 Access through Telnet

ĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂ

30

6.3 Access through Web

ĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂ

30

7 Basic Features and Specifications

ĂĂĂĂĂĂĂĂĂĂĂĂĂ

31

Contents

1 Product Overview

SICOM3000 includes a series of industrial Ethernet switches applied

in the wind power, distribution network automation, subway PIS and AFC,

power SCADA, sewage treatment, highway, metallurgy, hydroelectric

power, photovoltaic generation, subway CBTC, plant automation,

intelligent transportation, and many other industries.SICOM3000 is

applicable to harsh and hazardous industrial environments due to its

high-performance switching engine, solid closed housing, fanless but heat

dissipation-capable single-rib shaped chassis, overcurrent, overvoltage,

and EMC protection for power input, and sound EMC protection of RJ45

ports. The redundant network and power input support guarantees the

reliable operation of the system.

SICOM3000 provides powerful network management functions. The

device can be managed through CLI, Telnet, Web, SNMP-based and

OPC network management software.

The series switches support DIN rail and panel mounting.SICOM3000

provides up to two 1000Base-X, 10/100/1000Base-T(X) SFP slots

(gigabit SFP slots), two 100M cooper or fiber (optional) ports, and six

10/100Base-T(X) Ethernet ports. For details, see the following table.

Product Overview

1

Table 1 SICOM3000 Models

Note:

We reserve the right to amend the product information listed in this table without notice.

To obtain the latest information, contact our sales or technical support personnel.

Structure and Interface

2

2 Structure and Interface

Figure 1 Front Panel of SICOM3000-2GX-2S/M-6T

2.1 Front Panel

(1)(2)(3)(4)

(8)

(5)

G2

G1

Speed

Link/ACT

(7)

(6)

3

8

7

6

5

4

2

1

(9)

(10)

(11)

ƽ

Front Panel of SICOM3000-2GX-2S/M-6T

Caution:

It is recommended to purchase the port dustproof shield

(optional) to keep ports clean and ensure switch performance.

Structure and Interface

3

Table 2 Description of the Front Panel of SICOM3000-2GX-2S/M-6T

No. Identifie

r

Description

(1) PWR1 Power 1 LED

(2) PWR2 Power 2 LED

(3) Run Running LED

(4) Alarm Alarm LED

(5)

G2

Gigabit SFP slot (G2) and its connection

status LED

(6)

G1

Gigabit SFP slot (G1) and its connection

status LED

(7)

7

100Base-FX Ethernet port 7 and its

connection status LED

(8)

8

100Base-FX Ethernet port 8 and its

connection status LED

(9) 1-6 Six 10/100Base-T(X) Ethernet ports

(10)

Speed

10/100Base-T(X) Ethernet port speed

LED (yellow)

(11)

Link/ACT

10/100Base-T(X) Ethernet port connection

status LED (green)

Note:

The appearance of SICOM3000-MA-C-2GX-2S/M-6T is

identical with that of SICOM3000-2GX-2S/M-6T.

Structure and Interface

4

Figure 2 Front Panel of SICOM3000-2GX-8T

(1)(2)(3)(4)

(8)

(5)

G2

G1

Speed

Link/ACT

(7)

(6)

3

8

7

6

5

4

2

1

(9)

ƽ

Front Panel of SICOM3000-2GX-8T

Structure and Interface

5

Table 3 Description of the Front Panel of SICOM3000-2GX-8T

No. Identifie

r

Description

(1) PWR1 Power 1 LED

(2) PWR2 Power 2 LED

(3) Run Running LED

(4) Alarm Alarm LED

(5)

G2

Gigabit SFP slot (G2) and its connection

status LED

(6)

G1

Gigabit SFP slot (G1) and its connection

status LED

(7) 1-8 Eight 10/100Base-T(X) Ethernet ports

(8)

Speed

10/100Base-T(X) Ethernet port speed

LED (yellow)

(9)

Link/ACT

10/100Base-T(X) Ethernet port

connection status LED (green)

Structure and Interface

6

Figure 3 Top Panel

Table 4 Description of the Top Panel

2.2 Top Panel

PWR1 PWR2

+/L -/N -/N +/L

FAULT

Console

(1) (2) (3)

(4)

FAULT

+/L -/N -/N +/L

PWR1 PWR2

No. Identifie

r

Description

(1) Power terminal block

(2) Alarm terminal block

(3) Console Console port

wercs gnidnuorG -- )4(

Mounting

7

Figure 5 Dimensions for Panel Mounting (unit:mm)

Figure 4 Dimensions for DIN-Rail Mounting (unit:mm)

3 Mounting

3.1 Dimension Drawing

70

123

56

4

6.5

75

140

178

195

12375 75

6

35

140

Caution:

ƽ

As part of the heat dissipation system, the switch housing

becomes hot during operation. Please use caution when

coming in contact and avoid covering the switch housing

when the switch is running.

ƽ

The figures in this manual are only for reference.

Mounting

8

3.2 Mounting Modes and Steps

The series switches support DIN-rail and panel mounting. Before

installation, make sure that the following requirements are met.

1) Environment:temperature (-40ć to 85ć), ambient relative humidity

(5% to 95%, non-condensing)

2) Power requirement:The power input is within the voltage range of

the switch.

3) Grounding resistance:<5

Ω

4) No direct sunlight, distant from heat source and areas with strong

electromagnetic interference.

Step 1:Select the mounting position for the device and guarantee adequate

space and heat dissipation (dimensions:75mm×140mm×123mm).

Step 2:Insert the connecting seat onto the top of the DIN rail, and push

the bottom of the device inward and upward to ensure the DIN

rail fits in the connecting seat. Make sure the device is firmly

installed on the DIN rail, as shown in the following figure.

Figure 6 DIN-Rail Mounting

ƽ

DIN-Rail Mounting

3.2.1 Mounting

1

2

DIN rail

connecting seat

DIN rail

Mounting

9

Step 1: Insert the head of a screwdriver into the opening of the spring

locking piece at the bottom from the left. Lift the handle of the

screwdriver to open the spring locking piece of the connecting

seat, as shown on the left of the following figure.

Step 2: Move the device in direction 2 until the bottom of the device

is detached from the DIN rail. Then move the device in

direction 3 and uplift the device until the top of the connecting

seat is detached from the DIN rail.

Figure 7 DIN-Rail Dismounting

ƽ

DIN-Rail Dismounting

1

2

3

Screwdriver

DIN rail

connecting seat

DIN rail

Mounting

10

Figure 8 Panel Mounting

ƽ

Panel Mounting

3.2.2 Panel Mounting

Screw

2

1

Ф6.5

Ф4

Note:

Purchase the plate (optional) for panel mounting.

Step 1:Use screws to secure the plate for panel mounting to the rear

panel of the device.

Step 2:Select the mounting position (on a wall or inner wall of a

cabinet) for the device and guarantee adequate space and heat

dissipation (dimensions:75mm×140mm×123mm).

Step 3:Punch four holes in the selected position according to the

dimensions for panel mounting. Insert four screws into the four holes

respectively, and turn the screws with a screwdriver until about

a 5mm distance is left between each screw head and the wall.

Step 4:Align the four mounting holes on the plate for panel mounting

with the four screws. Insert the screws through the Ф6.5 positions

in the following figure. Move the device in direction 1 until the

screws are in the Ф4 positions. Then tighten the screws.

Mounting

11

Figure 9 Panel Dismounting

ƽ

Panel Dismounting

Screw

2

1

Ф6.5

Ф4

Step 1:Loosen the four screws with a screwdriver. Pull the device

upward until the four screws are in the Ф6.5 positions in the

following figure. Then remove the plate for panel mounting

from the four screws to detach the device from the wall or

inner wall of the cabinet.

Step 2:Loosen the screws completely with a screwdriver. Remove

them from the wall or inner wall of the cabinet. Then remove

the plate for panel mounting from the rear panel to complete

dismounting the device.

Connection

12

10/100Base-T(X) Ethernet port is equipped with RJ45 connector.

The port is self-adaptive. It can automatically configure itself to work

in 10M or 100M state, full or half duplex mode. The port can also

adapt to MDI or MDI-X connection automatically. You can connect

the port to a terminal or network device with a straight-through or

cross-over cable.

The following figure shows the pin numbers of the RJ45 port.

The following table lists the pin definitions of the 10/100Base-T(X)

RJ45 port.

4 Connection

4.1 10/100Base-T(X) Ethernet Port

Figure 10 RJ45 Port

Table 5 Pin Definitions of 10/100Base-T(X) RJ45 Port

ƽ

Pin Definition

Note:

"+" and "-" indicate level polarities.

Pin MDI-X Signal MDI Signal

1 Receive Data+ (RD+) Transmit Data+ (TD+)

2 Receive Data- (RD-) Transmit Data- (TD-)

3 Transmit Data+ (TD+) Receive Data+ (RD+)

6 Transmit Data- (TD-) Receive Data- (RD-)

4, 5, 7, 8 Unused Unused

Connection

13

ƽ

Wiring Sequence

Figure 11 Connection Using Straight-through/Cross-over Cable

RJ45 connector

Straight-through cable

Wiring sequence

Cross-over cable

Wiring sequence

RJ45 connector

8

1

2

3

6

1

2

3

6

1

2

3

6

3

6

1

2

Note:

The color of the cable for RJ45 connector meets the 568B

standard:1-orange and white, 2-orange, 3-green and white,

4-blue, 5-blue and white, 6-green, 7-brown and white, and 8-brown.

Connection

14

4.2 100Base-FX Ethernet Port

Figure 12 Connection of 100Base-FX Ethernet Port

Caution:

The device uses laser to transmit signals in fibers. The laser

meets the requirements of level 1 laser products. Routine

operation is not harmful to your eyes, but do not look directly

at the fiber port when the device is powered on.

Device A

SC-port

Device B

SC-port

SC-SC cable

Wiring sequence

TX

RX

TX

RX

TX

RX

TX

RX

100Base-FX Ethernet port is equipped with FC/ST/SC connector,

and each port consists of TX (transmit) port and RX (receive) port. To

enable data transmission between Device A and Device B, connect

the TX port of Device A to the RX port of Device B, and the RX port

of Device A to the TX port of Device B. The following uses an SC port

as an example. The wiring sequence of an ST/FC port is the same

with that of the SC port.

Pagina se încarcă...

KYLAND Technology SICOM3000 Hardware Installation Manual

KYLAND Technology SICOM3000 Hardware Installation Manual

în alte limbi

Alte documente