Yamaha RX-V565 Manualul proprietarului

RX-V565

AV Receiver

Ampli-tuner audio-vidéo

OWNER’S MANUAL

MODE D’EMPLOI

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

E

Caution-i En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean

place – away from direct sunlight, heat sources, vibration,

dust, moisture, and/or cold. Allow ventilation space of at least

30 cm on the top, 20 cm on the left and right, and 20 cm on

the back of this unit.

3 Locate this unit away from other electrical appliances, motors,

or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in an environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign objects may fall onto

this unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to

this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections

are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may

cause fire, damage to this unit, and/or personal injury. Yamaha

will not be held responsible for any damage resulting from use

of this unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power cord and

outdoor antennas disconnected from a wall outlet or the unit

during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed. The

cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the wall

outlet.

16 Install this unit near the AC outlet and where the AC power

plug can be reached easily.

17 Be sure to read the “Troubleshooting” section on common

operating errors before concluding that this unit is faulty.

18 Before moving this unit, press ASTANDBY/ON

to set this

unit in the standby mode, and disconnect the AC power plug

from the wall outlet.

19 VOLTAGE SELECTOR (Asia and General models only)

The VOLTAGE SELECTOR on the rear panel of this unit

must be set for your local main voltage BEFORE plugging

into the AC wall outlet. Voltages are:

...... AC 110/120/220/230–240 V, 50/60 Hz (General model)

..........................AC 220/230–240 V, 50/60 Hz (Asia model)

20 The batteries shall not be exposed to excessive heat such as

sunshine, fire or like.

21 Excessive sound pressure from earphones and headphones can

cause hearing loss.

22 When replacing the batteries, be sure to use batteries of the

same type. Danger of explosion may happen if batteries are

incorrectly replaced.

■ For U.K. customers

If the socket outlets in the home are not suitable for the

plug supplied with this appliance, it should be cut off and

an appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live

socket outlet.

■ Special Instructions for U.K. Model

Caution: Read this before operating your unit.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN

OR MOISTURE.

As long as this unit is connected to the AC wall outlet,

it is not disconnected from the AC power source even

if you turn off this unit by ASTANDBY/ON. In this

state, this unit is designed to consume a very small

quantity of power.

Note

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this apparatus

may not correspond with the coloured markings identifying

the terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured

BLACK. The wire which is coloured BROWN must be

connected to the terminal which is marked with the letter L or

coloured RED.

Making sure that neither core is connected to the earth

terminal of the three pin plug.

Caution-ii En

Caution: Read this before operating your unit.

Limited Guarantee for European Economic Area (EEA) and Switzerland

Thank you for having chosen a Yamaha product. In the unlikely event that your Yamaha product needs guarantee service, please contact the dealer from

whom it was purchased. If you experience any difficulty, please contact Yamaha representative office in your country. You can find full details on our

website (http://www.yamaha-hifi.com/ or http://www.yamaha-uk.com/ for U.K. resident).

The product is guaranteed to be free from defects in workmanship or materials for a period of two years from the date of the original purchase. Yamaha

undertakes, subject to the conditions listed below, to have the faulty product or any part(s) repaired, or replaced at Yamaha’s discretion, without any charge

for parts or labour. Yamaha reserves the right to replace a product with that of a similar kind and/or value and condition, where a model has been

discontinued or is considered uneconomic to repair.

Conditions

1. The original invoice or sales receipt (showing date of purchase, product code and dealer’s name) MUST accompany the defective product, along with a

statement detailing the fault. In the absence of this clear proof of purchase, Yamaha reserves the right to refuse to provide free of charge service and the

product may be returned at the customer’s expense.

2. The product MUST have been purchased from an AUTHORISED Yamaha dealer within the European Economic Area (EEA) or Switzerland.

3. The product must not have been the subject of any modifications or alterations, unless authorised in writing by Yamaha.

4. The following are excluded from this guarantee:

a. Periodic maintenance and repair or replacement of parts due to normal wear and tear.

b. Damage resulting from:

(1) Repairs performed by the customer himself or by an unauthorised third party.

(2) Inadequate packaging or mishandling, when the product is in transit from the customer. Please note that it is the customer’s responsibility to

ensure the product is adequately packaged when returning the product for repair.

(3) Misuse, including but not limited to (a) failure to use the product for its normal purpose or in accordance with Yamaha’s instructions on the proper

use, maintenance and storage, and (b) installation or use of the product in a manner inconsistent with the technical or safety standards in force in

the country where it is used.

(4) Accidents, lightning, water, fire, improper ventilation, battery leakage or any cause beyond Yamaha’s control.

(5) Defects of the system into which this product is incorporated and/or incompatibility with third party products.

(6) Use of a product imported into the EEA and/or Switzerland, not by Yamaha, where that product does not conform to the technical or safety

standards of the country of use and/or to the standard specification of a product sold by Yamaha in the EEA and/or Switzerland.

(7) Non AV (Audio Visual) related products.

(Products subject to “Yamaha AV Guarantee Statement” are defined in our website at http://www.yamaha-hifi.com/ or

http://www.yamaha-uk.com/ for U.K. resident.)

5. Where the guarantee differs between the country of purchase and the country of use of the product, the guarantee of the country of use shall apply.

6. Yamaha may not be held responsible for any losses or damages, whether direct, consequential or otherwise, save for the repair or replacement of the

product.

7. Please backup any custom settings or data, as Yamaha may not be held responsible for any alteration or loss to such settings or data.

8. This guarantee does not affect the consumer’s statutory rights under applicable national laws in force or the consumer’s rights against the dealer arising

from their sales/purchase contract.

Information for Users on Collection and Disposal of Old Equipment and used Batteries

These symbols on the products, packaging, and/or accompanying documents mean that used electrical

and electronic products and batteries should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products and used batteries, please take them to

applicable collection points, in accordance with your national legislation and the Directives 2002/96/

EC and 2006/66/EC.

By disposing of these products and batteries correctly, you will help to save valuable resources and

prevent any potential negative effects on human health and the environment which could otherwise

arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries, please contact your

local municipality, your waste disposal service or the point of sale where you purchased the items.

[Information on Disposal in other Countries outside the European Union]

These symbols are only valid in the European Union. If you wish to discard these items, please contact

your local authorities or dealer and ask for the correct method of disposal.

Note for the battery symbol (bottom two symbol examples):

This symbol might be used in combination with a chemical symbol. In this case it complies with the

requirement set by the Directive for the chemical involved.

1 En

English

INTRODUCTION

APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

Features.................................................................... 2

About this manual................................................... 3

Supplied accessories................................................ 3

Part names and functions....................................... 4

Front panel ................................................................. 4

Rear panel .................................................................. 5

Front panel display..................................................... 6

Remote control........................................................... 7

Quick start guide..................................................... 8

L

Preparing remote control ....................................... 9

Installing batteries in the remote control ................... 9

Using the remote control............................................ 9

Connections ...........................................................10

Placing speakers....................................................... 10

Connecting speakers ................................................ 11

Information on jacks and cable plugs ...................... 13

Connecting a TV monitor or projector .................... 14

Connecting other components ................................. 15

Connecting a Yamaha iPod universal dock or

Bluetooth™ wireless audio receiver.................... 16

Using the VIDEO AUX jacks on the front panel .... 16

Connecting the FM and AM antennas ..................... 17

Connecting the power cable..................................... 17

Turning this unit on and off ..................................... 17

Optimizing the speaker setting for your

listening room (YPAO) ..................................... 18

Using Auto Setup..................................................... 18

When an error message is displayed during

measurement ........................................................ 20

When a warning message is displayed after

measurement ........................................................ 20

Playback................................................................. 21

Basic procedure........................................................ 21

Using the SCENE function ...................................... 21

Muting audio output temporarily (MUTE).............. 22

Adjusting high/low frequency sound

(tone control) ....................................................... 22

Enjoying pure hi-fi sound ........................................ 22

Using the sleep timer ............................................... 22

Using your headphones............................................ 22

Displaying input signal information ........................ 23

Changing information on the front panel display .... 23

Enjoy the sound field programs .......................... 24

Selecting sound field programs................................ 24

Enjoying unprocessed input sources

(Straight decoding mode) .................................... 27

Enjoying sound field programs without surround

speakers (Virtual CINEMA DSP) ....................... 27

Enjoy sound field programs with headphones

(SILENT CINEMA™) ........................................ 27

FM/AM tuning ......................................................28

Tuning in to the desired FM/AM station

(Frequency tuning) .............................................. 28

Registering FM/AM stations and tuning in

(Preset tuning)...................................................... 28

Radio Data System tuning

(Europe and Russia models only).................... 30

Displaying the Radio Data System information ...... 30

Selecting the Radio Data System program type

(PTY Seek mode) ................................................ 30

Using the enhanced other networks (EON) data

service.................................................................. 31

Using iPod™.......................................................... 32

Controlling iPod™................................................... 32

Using Bluetooth™ components ........................... 34

Pairing the Bluetooth™ wireless audio receiver

and your Bluetooth™ component........................ 34

Playback of the Bluetooth™ component ................. 34

Setting the option menu for each input source

(OPTION menu) ............................................... 35

OPTION menu items ............................................... 35

Editing surround decoders/sound field

programs ........................................................... 38

Selecting a decoder used with a sound field

program................................................................ 38

Setting sound field parameters................................. 38

Sound field parameters ............................................ 38

Operating various settings for this unit

(Setup menu) ..................................................... 40

Basic operation of the setup menu ........................... 41

Speaker Setup .......................................................... 41

Sound Setup ............................................................. 43

Function Setup ......................................................... 44

DSP Parameter ......................................................... 45

Memory Guard......................................................... 45

Controlling other components with the remote

control................................................................ 46

Setting remote control codes.................................... 46

Resetting all remote control codes........................... 46

Advanced setup..................................................... 47

Troubleshooting.................................................... 48

General..................................................................... 48

HDMI™................................................................... 51

Tuner (FM/AM) ....................................................... 51

Remote control......................................................... 52

iPod™ ...................................................................... 52

Bluetooth™.............................................................. 53

Auto Setup (YPAO)................................................. 53

Glossary ................................................................. 55

Sound field program information ....................... 57

Information on HDMI™...................................... 57

Additional information ........................................ 58

About the HDMI™ control function ....................... 58

Using the HDMI™ control function........................ 58

Specifications......................................................... 59

Index ...................................................................... 60

(at the end of this manual)

Contents

INTRODUCTION

PREPARATION

BASIC OPERATION

ADVANCED OPERATION

APPENDIX

List of remote control codes...................................i

2 En

INTRODUCTION

■ Built-in 7-channel power amplifier

• Minimum RMS Output Power (1 kHz, 0.9% THD, 6 Ω)

• FRONT L/R: 90 W + 90 W

• CENTER: 90 W

• SURROUND L/R: 90 W + 90 W

• SURROUND BACK L/R: 90 W + 90 W

■ Speaker/Preout outputs

• Speaker jacks (7-channel), preout output jacks

(subwoofer)

■ Input/Output terminals

Input terminals

• HDMI input x 4

• Audio/Visual input

[Audio] Digital input (coaxial) x 2, digital input

(optical) x 2, analog input x 2

[Video] Component video x 2, S Video x 1,

composite video x 4

• Audio input (analog) x 2

• Dock input x 1

• V-AUX input

[Audio] Analog x 1, stereo mini jack x 1

[Video] Composite video x 1

Output terminals

• Monitor output

[Audio/Video] HDMI x 1

[Video] Component video x 1, Composite video x 1

• Audio/Visual output

[Audio] Analog x 1

[Video] Composite video x 1

• Audio output

Analog x 1

■ Proprietary Yamaha technology for the

creation of sound fields

• CINEMA DSP

• Compressed Music Enhancer mode

• Virtual CINEMA DSP

• SILENT CINEMA

■ Digital audio decoders

• Dolby TrueHD, Dolby Digital Plus

• DTS-HD Master Audio, DTS-HD High Resolution

Audio, DTS Express

• Dolby Digital, Dolby Digital EX

• DTS, DTS 96/24, DTS-ES Matrix 6.1,

DTS-ES Discrete 6.1

• Dolby Pro Logic, Dolby Pro Logic II,

Dolby Pro Logic IIx

• DTS NEO:6

• DSD

■ Sophisticated FM/AM tuner

• 40-station random and direct preset tuning

• Automatic preset tuning

• Radio Data System tuning

■ HDMI™

(High-Definition Multimedia Interface)

• HDMI interface for standard, enhanced or high-

definition video as well as multi-channel digital audio

– Automatic audio and video synchronization (lip sync)

information capability

– Deep Color video signal (30/36 bit) transmission

capability

– “x.v.Color” video signal transmission capability

– High refresh rate and high resolution video signals

capability

– High definition digital audio format signals capability

• Analog video to HDMI digital video up-conversion

(composite video → HDMI, component video →

HDMI) capability for monitor out

• Analog video input up-scaling for HDMI digital video

output 576i or 576p → 720p, 1080i or 1080p

■ DOCK terminal

• DOCK terminal to connect a Yamaha iPod universal

dock (such as YDS-11, sold separately) or Bluetooth

wireless audio receiver (such as YBA-10, sold

separately)

■ Automatic speaker setup features

• “YPAO” (Yamaha Parametric Room Acoustic

Optimizer) for automatically optimizing speaker

outputs suitable for listening environments

■ Other features

• 192-kHz/24-bit D/A converter

• OSD (on-screen display) menus that allow you to

optimize this unit to suit your individual audiovisual

system

• Direct mode for pure hi-fi sound for all sources

• Adaptive dynamic range controlling capability

• Scene function that allows you to change input sources

and sound field programs with one key

• Sleep timer

Features

3 En

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

Manufactured under license from Dolby Laboratories.

Dolby, Pro Logic and the double-D symbol are trademarks of Dolby

Laboratories.

Manufactured under license under U.S. Patent No’s:

5,451,942;5,956,674;5,974,380;5,978,762;6,226,616;6,487,535 &

other U.S. and worldwide patents issued & pending. DTS is a

registered trademark and the DTS logos, Symbol, DTS-HD and DTS-

iPod™

“iPod” is a trademark of Apple Inc., registered in the U.S. and other

countries.

Bluetooth™

Bluetooth is a registered trademark of Bluetooth SIG and is used by

Yamaha in accordance with a license agreement.

“HDMI,” the “HDMI” logo and “High-Definition Multimedia

Interface” are trademarks, or registered trademarks of HDMI

Licensing LLC.

x.v.Color™

“x.v.Color” is a trademark of Sony Corporation.

“SILENT CINEMA” is a trademark of Yamaha Corporation.

Check that you received all of the following parts.

• Remote control

• Batteries (2) (AAA, R03, UM-4)

• Optimizer microphone

• AM loop antenna

• Indoor FM antenna

About this manual

• y indicates a tip for your operation.

• Some operations can be performed by using either the keys on the front panel or the ones on the remote control. In case the key names differ between

the front panel and the remote control, the key name on the remote control is given in parentheses.

• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In case of

differences between the manual and product, the product has priority.

• “ASTANDBY/ON” or “gHDMI 1” (example) indicates the name of the parts on the front panel or the remote control. Refer to the attached sheet

or “Part names and functions” on page 4 for the information about each position of the parts.

• ☞ indicates the page describing the related information.

Supplied accessories

4 En

A STANDBY/ON

Switches this unit between standby and on (see page 17).

B PHONES jack

For plugging headphones (see page 22).

C INFO

Changes information display screens on the front panel display

(see page 23).

D MEMORY

Registers FM/AM stations as preset stations (see page 29).

E PRESET l / h

Selects an FM/AM preset station (see page 29).

F FM

Sets the FM/AM tuner band to FM (see page 28).

G AM

Sets the FM/AM tuner band to AM (see page 28).

H TUNING l / h

Changes FM/AM tuner frequencies (see page 28).

I SCENE

Switches between linked sets of input sources and sound field

programs (see page 21).

J TONE CONTROL

Adjusts high-frequency/low-frequency output of speakers/

headphones (see page 22).

K PROGRAM l / h

Changes sound field programs (see page 24).

L STRAIGHT

Changes a sound field program to straight decoding mode (see

page 27).

M DIRECT

Changes a sound field program to direct mode (see page 22).

N INPUT l / h

Selects an input source (see page 21).

O OPTIMIZER MIC jack

For connecting the supplied optimizer microphone and adjusting

output characteristics of speakers (see page 18).

P VOLUME control

Controls the volume of this unit (see page 21).

Q VIDEO (VIDEO AUX) jack

For connecting the video output cable of a camcorder or game

console (see page 16).

R AUDIO L/R (VIDEO AUX) jack

For connecting the audio output cable of a camcorder or game

console (see page 16).

S PORTABLE (VIDEO AUX) jack

For connecting the audio output cable of a portable music player

(see page 16).

T Front panel display

Displays information on this unit (see page 6).

U HDMI THROUGH

Lights up during pass-through output of an HDMI signal input

to this unit while this unit is on standby (see page 44).

Part names and functions

Front panel

PHONES

SILENT

CINEMA

TONE

CONTROL

PROGRAM

STRAIGHT

INPUT

OPTIMIZER

MIC

VIDEO

AUDIO

PORTABLE

THROUGH

VIDEO

AUX

VOLUME

HDMI

EFFECT

l

h

l

h

BD/DVD

TV

CD

RADIO

SCENE

INFO

MEMORY

PRESET

l

h

l

h

TUNING

FM

AM

STANDBY

/ON

DIRECT

A

T D G

J MC OK N

U PFE H

I RBLQS

5 En

Part names and functions

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

a DOCK terminal

For connecting an optional Yamaha iPod universal dock (YDS-

11) or Bluetooth wireless audio receiver (YBA-10) (see

page 16).

b HDMI OUT/HDMI 1-4

For connecting an HDMI-compatible video monitor or external

components for HDMI inputs 1-4 (see page 15).

c ANTENNA jack

For connecting supplied FM and AM antennas (see page 17).

d SPEAKERS terminal

For connecting front right and left, center, surround and

surround back speakers (see page 11).

e AV 1-6

For connecting external components for audio/visual inputs 1-6

(see page 15).

f AV OUT

Outputs audio/visual signals from a selected analog input source

to an external component (see page 16).

g AUDIO 1/2

For connecting external components for audio inputs 1-2 (see

page 16).

h MONITOR OUT

Outputs visual signals from this unit to a video monitor, such as

a TV (see page 14).

i AUDIO OUT

Outputs audio signals from a selected analog input source to an

external component (see page 16).

j PRE OUT

For connecting a subwoofer with a built-in amplifier (see

page 11).

k Power Cable

For connecting this cable to an AC wall outlet (see page 17).

Rear panel

S VIDEO

UNBAL.

FM

GND

AM

ANTENNA

PR

PB

Y

COMPONENT

VIDEO

SPEAKERS

DOCK

VIDEO

PR

PB

Y

OPTICAL

(

TV

)

A

V

1

AV 2

COAXIAL

AV 3

(

CD

)

COAXIAL

OPTICAL

AV 4

AV 5

AV

OUT

AUDI O1

AUDIO2

VIDEO

HDMI

HDMI 1

(

BD/DVD

)

HDMI 2 HDMI 3

HDMI 4

OUT

AV 6

VIDEO

MONITOR OUT

AUDIO

OUT

FRONT

CENTER

SURROUND

PRE OUT

SUBWOOFER

BACK/

BI-AMP

SURROUND

COMPONENT

abc

efhgi j

kd

6 En

Part names and functions

a HDMI indicator

Lights up during normal communication when HDMI is

selected as an input source.

b CINEMA DSP indicator

Lights up when a sound field program that uses CINEMA DSP

is selected.

c Tuner indicator

Lights up while receiving a radio broadcast signal from an FM/

AM station (see page 28).

d SLEEP indicator

Lights up when the sleep timer is activated (see page 22).

e VOLUME indicator

Displays volume levels.

f MUTE indicator

Flashes when audio is muted.

g Cursor indicators

Light up if corresponding cursors on the remote control are

available for operations.

h Multi information display

Displays menu items and settings for the current operation.

i Speaker indicators

Indicate speaker terminals from which signals are currently

output.

Front panel display

STEREO

SLEEP

VOL.

TUNED

SW

C

LR

SL SR

SBL SB SBR

MUTE

abcdef

gh ig

SW

C

LR

SL SR

SBL SB SBR

Subwoofer

Front L

Surround L

Surround back L

Center

Front R

Surround R

Surround back R

Surround back

7 En

Part names and functions

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

a Remote control signal transmitter

Transmits infrared signals.

b TRANSMIT

Lights up when a signal is output from the remote control.

c CODE SET

Sets remote control codes for external component operations

(see page 46).

d SOURCE POWER

Switches an external component on and off.

e SLEEP

Switches the sleep timer operations (see page 22).

f POWER

Switches this unit on and standby.

g Input selection keys

h Tuner keys

i INFO

Changes the information shown on the front panel display (see

page 23).

j Sound selection keys

Selects sound field programs (see page 24).

k SCENE

Switches between linked sets of input sources and sound field

programs (see page 21).

l SETUP

Displays the setup menu (see page 41).

m OPTION

Displays the option menu (see page 35).

n Cursors k / n / l / h/ENTER/RETURN

o VOLUME +/–

Adjust the volume of this unit (see page 21).

p DISPLAY

Changes the operation mode of the iPod connected to the

Yamaha iPod universal dock (see page 32).

q MUTE

Turns the mute function of the sound output on and off (see

page 22).

r External component operation keys

Operate recording, playback etc. of external components (see

page 46).

s Numeric keys

Enter numbers.

t TV control keys

Operate a monitor such as a TV or projector.

Remote control

POWER

1234

1256

1234

7856

90

10

1234

POWER

SOURCE

V-AUX

[ A ] [ B ] DOCK

TUNER

FM

MOVIE

BD

DVD

TOP

MENU

MUSIC

SCENE

TV

CD

OPTIONSETUP

RETURN

REC

ENT

POWER

TV

TV VOL

INPUT

MUTE

TV CH

ENTER

VOLUME

DISPLAY

MUTE

MENU

RADIO

STEREO

ENHANCER SUR. DECODE

DIRECTSTRAIGHT

INFO

MEMORY

AM

PRESET

SLEEP

HDMI

AV

AUDIO

TRANSMIT

CODE SET

TUNING

a

d

e

f

g

h

j

k

l

m

o

p

q

r

s

t

b

c

n

i

HDMI 1-4

Selects HDMI inputs 1 through 4.

AV 1-6

Selects AV inputs 1 through 6.

AUDIO 1/2

Selects AUDIO inputs 1 and 2.

V-AUX

Selects the V-AUX jack on the front

panel of this unit.

[A]/[B]

To control external components using

the rExternal component

operation keys separately from

operations of this unit (see page 46).

DOCK

Selects a Yamaha iPod universal dock/

Bluetooth wireless audio receiver

connected to the DOCK terminal.

TUNER

Selects the FM/AM tuner.

FM

Switches a band between FM and AM.

AM

MEMORY

Presets radio stations.

PRESET k / n

Selects a preset station.

TUNING k / n

Changes tuning frequencies.

Cursors k / n / l / h

Select menu items displayed on the

front panel display or on a video

monitor, or change settings.

ENTER

Confirms a selected item.

RETURN

Returns to the previous screen or

ends the menu display.

8 En

When you use this product for the first time, perform setup following the steps below. See the related pages for details on

operations and settings.

Prepare speakers, DVD player, cables, and other items

necessary for setup.

For example, prepare the following items for setting up a

5.1-channel sound system.

y

• Prepare two speakers (for front). The priority of the requirement of other

speakers is as follows:

1 Two surround speakers

2 One center speaker

3 One (or two) surround back speaker(s)

• If your video monitor is a CRT, we recommend that you use magnetically

shielded speakers.

Place your speakers in the room and connect them to this

unit.

y

• This unit has a YPAO (Yamaha Parametric Room Acoustic Optimizer)

that automatically optimizes this unit based on room acoustic

characteristics (audio characteristics of the speakers, speaker positions,

and room acoustics, etc.).

You can enjoy good balanced sound without special knowledge by using

the YPAO technology (see page 18).

Connect your TV, DVD player, or other components.

Connect the power cable and turn on this unit.

Select the component connected in the step 3 as an input

source and start playback.

y

• This unit supports the SCENE function that changes the input source and

sound field program at one time. Four scenes are preset for different

purposes for Blu-ray disc, DVD and CD, and you can select from a scene

from those just by pressing a remote control key. See page 21 for details.

Quick start guide

Step 1: Prepare items for setup

Requirements qty.

Speakers Front speaker 2

Center speaker 1

Surround speaker 2

Active subwoofer 1

Speaker cable 5

Subwoofer cable 1

Reproduction component such as DVD player 1

Video monitor such as TV 1

Video cable or HDMI cable 2

Audio cable 2

Front right speaker

Subwoofer

Surround left speaker

Surround right speaker

Front left speaker

Video monitor

Center speaker

Components

(such as DVD player)

Step 2: Set up your speakers

• Placing speakers ☞P. 10

• Connecting speakers ☞P. 11

Step 3: Connect your components

• Connecting a TV monitor or projector ☞P. 14

• Connecting other components ☞P. 15

• Connecting a Yamaha iPod universal dock or

Bluetooth wireless audio receiver ☞P. 16

• Connecting the FM and AM antennas ☞P. 17

Step 4: Turn on the power

• Connecting the power cable ☞P. 17

• Turning this unit on and off ☞P. 17

Step 5: Select the input source and start

playback

• Basic procedure ☞P. 21

• Selecting sound field programs ☞P. 24

9 En

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

PREPARATION

1 Take off the battery compartment cover.

2 Insert the two supplied batteries (AAA, R03,

UM-4) according to the polarity markings (+

and –) on the inside of the battery

compartment.

3 Snap the battery compartment cover back

into place.

Notes

• Change all batteries if you notice the following conditions:

– the operation range of the remote control narrows

– the transmit indicator does not flash or is dim

• Do not use old batteries together with new ones.

This may shorten the life of the new batteries or cause old batteries

to leak.

• Do not use different types of batteries (such as alkaline and

manganese batteries) together. Specification of batteries may be

different even though they look the same.

• If you find leaking batteries, discard the batteries immediately,

taking care not to touch the leaked material. If the leaked material

comes into contact with your skin or gets into your eyes or mouth,

rinse it away immediately and consult a doctor. Clean the battery

compartment thoroughly before installing new batteries.

• Dispose of the old batteries correctly in accordance with your local

regulations.

• If the remote control is without batteries for more than 2 minutes,

or if exhausted batteries remain in the remote control, the contents

of the memory may be cleared. In such a case, install new batteries

and set the remote control code.

The remote control transmits a directional infrared ray. Be

sure to aim the remote control directly at the remote

control sensor on this unit during operation.

Notes

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following conditions:

– places of high humidity, such as near a bath

– places of high temperatures, such as near a heater or stove

– places of extremely low temperatures

– dusty places

y

• You can operate external components with this remote control by setting

the remote control code. See page 46 for details.

Preparing remote control

Installing batteries in the remote

control

1

3

2

Using the remote control

30 30

Remote control sensor window

within 6 m (20 ft)

10 En

This unit supports up to 7.1-channel surround. We recommend the following speaker layout in order to obtain the

optimum surround effect.

7.1-channel speaker layout

6.1-channel speaker layout

5.1-channel speaker layout

■ Front left and right speakers (FL and FR)

The front speakers are used for the front channel sounds

(stereo sound) and effect sounds. Place these speakers at

an equal distance from the ideal listening position. When

using a screen, the appropriate top positions of the

speakers are about 1/4 of the screen from the bottom.

■ Center speaker (C)

The center speaker is for the center channel sounds

(dialog, vocals, etc.). Place it halfway between the left and

right speakers. When using a TV, place the speaker just

above or just under the center of the TV with the front

surfaces of the TV and the speaker aligned. When using a

screen, place it just under the center of the screen.

■ Surround left and right speakers (SL and SR)

The surround speakers are used for effect and surround

sounds.

Place them at the rear left and rear right facing the

listening position.

To obtain a natural sound flow in the 5.1-channel speaker

layout, place them slightly further back than in the 7.1-

channel speaker layout.

■ Surround back left and right speakers (SBL

and SBR) / Surround back speaker (SB)

The surround back left and right speakers are used for rear

effect sounds. Place them at the rear of the room facing the

listening position at least 30 cm away from each other,

ideally at the same distance as that between the front left

and right speakers.

In the 6.1-channel speaker layout, surround back left and

right channel sound signals are mixed down and output

from the single surround back speaker.

In the 5.1-channel speaker layout, surround back left and

right channel sound signals are output from the surround

left and right speakers.

■ Subwoofer (SW)

The subwoofer speaker is used for bass sounds and low-

frequency effect (LFE) sounds included in Dolby Digital

and DTS signals. Use a subwoofer with a built-in

amplifier, such as the Yamaha Active Servo Processing

Subwoofer System. Place it exterior to the front left and

right speakers facing slightly inward to reduce reflections

from a wall.

Connections

Placing speakers

60˚

30˚

SBR

SBL

FL

FR

C

SL

SR

80˚

SL

SW

30 cm (12 in) or more

60˚

30˚

SB

FL

FR

C

SL

SR

80˚

SL

SW

60˚

30˚

FL

FR

C

SL

SR

80˚

SL

SW

Speaker channels

11 En

Connections

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

When you connect speakers, connect them to the respective terminals as follows, according to your speaker layout.

■ 7.1-channel

■ 6.1-channel

■ 5.1-channel

Connecting speakers

SPEAKERS

FRONT

CENTER

SURROUND

PRE OUT

SUBWOOFER

BACK/

BI-AMP

SURROUND

DMI

3

HDMI 4

AU

DI

O

OUT

e d

b

a

c

g f

h

Speakers Jacks on this unit

a Front speaker L FRONT (L)

b Front speaker R FRONT (R)

c Center speaker CENTER

d Surround speaker L SURROUND (L)

e Surround speaker R SURROUND (R)

f Surround back speaker L SURROUND

BACK/BI-AMP (L)

g Surround back speaker R SURROUND

BACK/BI-AMP (R)

h Subwoofer SUBWOOFER

Speakers Jacks on this unit

a Front speaker L FRONT (L)

b Front speaker R FRONT (R)

c Center speaker CENTER

d Surround speaker L SURROUND (L)

e Surround speaker R SURROUND (R)

f Surround back speaker SURROUND

BACK/BI-AMP (L)

h Subwoofer SUBWOOFER

Speakers Jacks on this unit

a Front speaker L FRONT (L)

b Front speaker R FRONT (R)

c Center speaker CENTER

d Surround speaker L SURROUND (L)

e Surround speaker R SURROUND (R)

h Subwoofer SUBWOOFER

12 En

Connections

■ Connecting to the FRONT terminals

1 Remove approximately 10 mm (0.4 in) of

insulation from the end of each speaker

cable and then twist bare wires of the cable

together so that they will not cause a short

circuits.

2 Loosen the knob, insert the twisted bare

wires into the hole, and then tighten the

knob.

■ Connecting to the CENTER, SURROUND,

SURROUND BACK/BI-AMP terminals

1 Press down the tab and insert the bare end of

the speaker cable into the hole in the

terminal.

2 Release the tab to secure the wire.

You can connect speakers that support bi-amplification

connections to this unit. Before connecting the speakers,

set this unit to enable bi-amplification connections in

“ADVANCED SETUP” (see page 47), and connect the

speakers to this unit as shown below.

Connecting the speaker cable

Caution

• A speaker cable is a pair of insulated cables running side by side in general. One of the cables is colored differently

or striped to indicate a polarity. Connect one end of the colored/striped cable to the “+” (red) terminal of this unit

and the other end to that of your speaker, and connect one end of the other cable to the “–” (black) terminal of this

unit and the other end to that of your speaker.

• Before connecting the speakers, be sure to disconnect the power cable.

• Do not let the bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or

speakers. If the circuit shorts out, “CHECK SP WIRES!” appears on the front panel display when this unit is turned on.

• Use magnetically shielded speakers. If images on the monitor are still distorted even when you use the magnetically

shielded speakers, place the speakers away from the monitor.

• Use speakers with an impedance of 6-ohm or larger.

Connecting the banana plug (Except U.K.,

Europe, Asia and Korea models)

Tighten the knob, and then insert the banana plug into

the end of the terminal.

10 mm (0.4 in)

1

2

3

Red: positive (+)

Black: negative (–)

Banana plug

Using bi-amplification connections

Caution

Before making bi-amplification connections, remove

any or cables that connect a woofer with a tweeter.

Refer to the instruction manuals of speakers for details.

When not making bi-amplification connections, make

sure that the brackets or cables are connected before

connecting the speaker cables.

Red: positive (+)

Black: negative (–)

FRONT

BACK/

BI-AMP

SURROUND

Front speakers

Right Left

This unit

13 En

Connections

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

This unit has the following input and output jacks. Use jacks and cables appropriate for components that you are

connecting.

■ Audio jacks

■ Video jacks

■ Video/audio jacks

y

• We recommend that you use a commercially available 19-pin HDMI

cable no longer than 5 meters (16 feet) with the HDMI logo printed on it.

• You can check the potential problem about the HDMI connection (see

page 23).

• You can check error information on HDMI connections (see page 23).

Information on jacks and cable plugs

Jack and cables Description

AUDIO jacks To transmit conventional analog

left and right audio signals. Use

stereo pin cables. Connect red

plugs to red jacks (R) and white

plugs to white jacks (L).

COAXIAL jacks To transmit coaxial digital audio

signals. Use pin cables for digital

audio signals.

OPTICAL jacks To transmit optical digital audio

signals. Use optical fiber cables for

optical digital audio signals.

Jack and cables Description

VIDEO jacks To transmit conventional

composite video signals. Use video

pin cables.

S VIDEO jack To transmit S-video signals that

include luminance (Y) and

chrominance (C) components. Use

S-video cables.

COMPONENT VIDEO

jacks

To transmit component video

signals that include luminance (Y),

chrominance blue (PB) and

chrominance red (PR) components.

Use component video cables.

AUDIO

L

R

(white)

(red)

COAXIAL

C

(orange)

OPTICAL

O

VIDEO

V

(yellow)

S VIDEO

S

PR

PB

Y

COMPONENT

VIDEO

P

B

Y

P

R

(red)

(blue)

(green)

Jack and cables Description

HDMI jacks To transmit digital video and

digital audio signals. Use HDMI

cables.

A video signal input to this unit is output from the

output terminals in MONITOR OUT for the same kind

of signal as the input signal.

For example, if a VCR with a composite output signal

and a DVD player with a COMPONENT VIDEO

output signal are connected, connect both VIDEO jack

and COMPONENT VIDEO jack in MONITOR OUT

to the video monitor.

If an HDMI input compatible monitor is connected, this

unit automatically converts an analog signal that is

input from a video input terminal to a digital video

signal, and then output it from the HDMI OUT jack.

HDMI

VIDEO

COMPONENT

VIDEO

Y

PB

PR

HDMI

VIDEO

COMPONENT

VIDEO

Y

PB

PR

S VIDEO

Input Output

Repeat Converted

14 En

Connections

Connect a video monitor such as a TV or projector to an output terminal of this unit. You can select one of the following

three types according to the input signal format supported by the video monitor.

Note

• When you connect this unit to the video monitor, make sure that this unit is on standby.

■ To connect an HDMI video monitor

■ To connect component video monitor

Note

• Only video signals input from this unit via the component input terminal

are output from the component output terminal.

■ To connect composite video monitor

Note

• Only video signals input from this unit via the composite video input

terminal are output from the composite video output terminal.

To output sound of a TV from this unit, make connection

between the AV input 1-6 and an audio output terminal.

If the TV supports an optical digital output, we

recommend that you use the AV input 1. Connecting to the

AV input 1 allows you to switch an input source to the AV

input 1 with just a single key operation using the SCENE

function (see page 21).

Connecting a TV monitor or projector

Jacks on components Jacks on this unit

a HDMI input HDMI OUT

Jacks on components Jacks on this unit

b Component video output MONITOR OUT

(COMPONENT VIDEO)

Jacks on components Jacks on this unit

c Video input (composite) MONITOR OUT (VIDEO)

PR

PB

Y

COMPONENT

VIDEO

HDMI

OUT

VIDEO

MO

NIT

O

R

OUT

S VIDE

O

U

NBAL.

FM

G

ND

AM

ANTENNA

HDMI 1

(

B

D/DV

D

)

HDMI 2

HD

HDMI

V

a

c

b

P

B

YP

R

TV, or projector

Outputting sound of a TV from this unit

OPTICAL

(

TV

)

AV

1

S VIDEO

UNBAL.

FM

GND

AM

P

R

P

B

Y

AV 1

AV 2

COAXIAL

AV 3

(

CD

)

COAXIAL

OPTICAL

AV 4

AV 5

AV

OUT

VIDEO

AV 6

O

Digital output

(optical)

TV, or projector

15 En

Connections

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

This unit has input and output terminals for respective input and output sources. You can reproduce sound and movies

from input sources selected with the front panel display or remote control.

Note

• When you connect this unit to the external components, make sure that this unit is on standby.

■ Audio and video player / Set-top box

y

• Input sources in parentheses are recommended to connect to the respective jacks. If your Yamaha component has the Remote in/out terminal, you can

switch the input source to that component with a single key operation using the SCENE function (see page 21).

• You can change the name of the input source displayed on the front panel display or the OSD on the video monitor as necessary (see page 45).

Connecting other components

Output jacks on the connected external component

Input sources/jacks of this unit

External

components

Signals Output jacks

External component

with HDMI output

Audio/Video HDMI output HDMI 1 (BD/DVD) HDMI 1

HDMI 2 HDMI 2

HDMI 3 HDMI 3

HDMI 4 HDMI 4

External component

with component video

output

Audio Optical digital output AV 1 (TV) OPTICAL

Video Component video output COMPONENT VIDEO

Audio Coaxial digital output AV 2 COAXIAL

Video Component video output COMPONENT VIDEO

External component

with S video output

Audio Analog audio output AV 5 AUDIO

Video S video output S VIDEO

External component

with composite video

output

Audio Coaxial digital output AV 3 (CD) COAXIAL

Video Composite output VIDEO

Audio Optical digital output AV 4 OPTICAL

Video Composite output VIDEO

Audio Analog audio output AV 5 AUDIO

Video Composite output VIDEO

Audio Analog audio output AV 6 AUDIO

Video Composite output VIDEO

S VIDEO

VIDEO

P

R

P

B

Y

OPTICAL

(

TV

)

A

V 1

AV 2

COAXIAL

AV 3

(

CD

)

COAXIAL OPTICAL

AV 4

AV 5

AV

OUT

AUDIO1

AUDIO2

VIDEO

HDMI 1

(

BD/DVD

)

H

DMI 2

H

DMI 3

HDMI

4

AV 6

AUDIO

OUT

COMPONENT

UNBAL.

F

M

G

N

D

A

M

ANTENNA

P

R

P

B

Y

CO

MP

O

NEN

T

V

IDE

O

DOCK

HDMI

OUT

V

IDE

O

M

ONITOR OUT

F

R

O

N

T

C

E

Audio / video input (AV 1-6) Audio / video output (AV OUT)

Audio input (AUDIO 1-2)

HDMI input

(HDMI 1-4)

Audio output

(AUDIO OUT)

16 En

Connections

■ Audio player

y

• We recommend connecting the coaxial digital output terminal of a CD player to the AV3 jack.

This unit has the DOCK terminal, to which you can

connect a Yamaha iPod universal dock (YDS-11, sold

separately) or a Bluetooth wireless audio receiver (YBA-

10, sold separately). You can play an iPod or a Bluetooth

component with this unit by connecting it to the DOCK

terminal.

Use a dedicated cable for connection between the dock/

receiver and this unit.

Use the VIDEO AUX jacks on the front panel to connect a

game console or a video camera to this unit. Be sure to

turn down the volume of this unit and other components

before making connections.

Note

• When external components are connected both the PORTABLE jack and

AUDIO jack, sound input from the PORTABLE jack is output.

Output jacks on the connected external component

Input sources/jacks of this unit

External components Output jacks

External component with optical digital

output

Optical digital output AV 1 (TV) OPTICAL

AV 4 OPTICAL

External component with coaxial digital

output

Coaxial digital output AV 2 COAXIAL

AV 3 (CD) COAXIAL

External component with analog audio

output

Analog audio output AV 5 AUDIO

AV 6 AUDIO

AUDIO 1 AUDIO

AUDIO 2 AUDIO

About audio/video output terminals

Among the analog audio and analog video signals input to this unit via input terminals, the audio/video signals of the

selected input sources are output from the AV OUT jack and AUDIO OUT jack. An HDMI input signal,

COMPONENT VIDEO input signal or digital audio input signal cannot be output.

When using the AV OUT jack: connect an external component to the composite or analog audio terminal.

When using the AUDIO OUT jack: connect an external component to the analog audio terminal.

Connecting a Yamaha iPod universal

dock or Bluetooth™ wireless audio

receiver

DOCK

S

VIDE

O

UNBAL

.

FM

G

N

D

ANTENNA

V

IDE

O

P

R

P

B

Y

V

IDE

O

HDMI

OUT

CO

MP

O

NENT

Yamaha iPod universal

dock/Bluetooth wireless

audio receiver

Using the VIDEO AUX jacks on the

front panel

VIDEO

AUDIO

PORTABLE

VIDEO

AUX

OG

RA

M

S

TRAI

G

HT

INPUT

O

PTIMIZE

R

MI

C

V

O

L

U

M

E

EFFE

CT

h

l

h

B

D/DV

D

TV

CD

RADI

O

SC

ENE

P

RE

S

ET

l

h

l

h

T

UNIN

G

FM

AM

DIRE

C

T

R

L

AUDIO

VIDEO

V

L

R

PORTABLE

Game console/Camcorder Music player

Analog audio

output

Analog audio

output

Video output

Pagina se încarcă ...

Yamaha RX-V565 Manualul proprietarului

Yamaha RX-V565 Manualul proprietarului

în alte limbi

Lucrări conexe

Alte documente