Parkside PABS 20-Li D5 Translation Of The Original Instructions

CORDLESS DRILL PABS 20-Li D5

AKKU-BOHRSCHRAUBER

Originalbetriebsanleitung

IAN 331803_1907

CORDLESS DRILL

Translation of the original instructions

АКУМУЛАТОРНА БОРМАШИНА

Превод на оригиналното ръководство за експлоатация

MAȘINĂ DE ÎNȘURUBAT ȘI GĂURIT,

CU ACUMULATOR

Traducerea instrucţiunilor de utilizare original

ΕΠΑΝΑΦΟΡΤΙΖΟΜΕΝΟ

ΔΡΑΠΑΝΟΚΑΤΣΑΒΙΔΟ

Μετάφραση των αυθεντικών οδηγιών λειτουργίας

AKU BUŠILICA-ODVIJAČ

Prijevod originalnih uputa za uporabu

AKU BUŠILICA-ODVIJAČ

Prevod originalnog uputstva za upotrebu

GB / CY Translation of the original instructions Page 1

HR Prijevod originalnih uputa za uporabu Stranica 15

RS Prevod originalnog uputstva za upotrebu Strana 29

RO Traducerea instrucţiunilor de utilizare original Pagina 43

BG Превод на оригиналното ръководство за експлоатация Cтраница 57

GR / CY Μετάφραση των αυθεντικών οδηγιών λειτουργίας Σελίδα 73

DE / AT / CH Originalbetriebsanleitung Seite 89

Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the

device.

Rasklopite prije čitanja obije stranice sa slikama i nakon toga se upoznajte sa svim funkcijama uređaja.

Pre čitanja rasklopite obe strane sa slikama te se upoznajte sa svim funkcijama uređaja.

Înainte de a citi instrucţiunile, priviţi ambele pagini cu imagini şi familiarizaţi-vă cu toate funcţiile aparatului.

Преди да прочетете отворете двете страници с фигурите и след това се запознайте с всички

функции на уреда.

Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τις δυο σελίδες με τις εικόνες και εξοικειωθείτε με όλες τις

λειτουργίες της συσκευής.

Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie sich anschließend

mit allen Funktionen des Gerätes vertraut.

A

20V max.

18V

All Parkside tools and the chargers PLG 20 A1/PLG 20 A2/PLG 20 A3 of the X20V Team series

are compatible with the PAP 20 A1/PAP 20 A2/PAP 20 A3 battery pack.

Charging times

Charging currents

2 Ah

Battery pack

PAP 20 A1

3 Ah

Battery pack

PAP 20 A2

4 Ah

Battery pack

PAP 20 A3

max. 2.4 A

Charger PLG 20 A1

60 min

2,4 A

90 min

2,4 A

120 min

2,4 A

max. 3.5 A

Charger PLG 20 A2

60 min

2,4 A

60 min

3,5 A

80 min

3,5 A

max. 4.5 A

Charger PLG 20 A3

45 min

3,5 A

45 min

4,5 A

60 min

4,5 A

B C

D E

F G

H I

J K

L

PABS 20-Li D5

GB

│

CY

│

1 ■

Contents

Introduction ......................................................2

Intended use ................................................................ 2

Features ................................................................... 2

Package contents ............................................................ 2

Technical data .............................................................. 2

General power tool safety warnings .................................3

1. Work area safety .......................................................... 3

2. Electrical safety ........................................................... 3

3. Personal safety ............................................................ 4

4. Power tool use and care .................................................... 4

5. Use and handling of the cordless electrical power tool ............................. 5

6. Service .................................................................. 5

Safety instructions for drills .........................................6

Original accessories/attachments ............................................... 6

Safety guidelines for battery chargers ............................................ 6

Before use .......................................................7

Charging the battery pack (see ﬁg. A) ............................................ 7

Inserting/removing the battery pack ............................................. 7

Checking the battery charge level ............................................... 7

Changing tools .............................................................. 7

Torque selection ring/drill setting ................................................ 7

2-speed gearbox ............................................................ 8

Use .............................................................8

Switching on/oﬀ ............................................................. 8

Setting the rotational speed .................................................... 8

Changing the direction of rotation ............................................... 8

Tips and tricks ............................................................... 8

Maintenance and cleaning ..........................................9

Kompernass Handels GmbH warranty ...............................9

Service .........................................................11

Importer .......................................................11

Disposal ........................................................11

Translation of the original Conformity Declaration .....................12

Ordering a replacement battery ....................................13

Telephone ordering ......................................................... 13

IB_331803_PABS20-LiD5_LB7.indb 1 25.02.20 15:16

PABS 20-Li D5

■ 2

│

GB

│

CY

CORDLESS DRILL PABS 20-Li D5

Introduction

Congratulations on the purchase of your new appli-

ance. You have chosen a high-quality product. The

operating instructions are part of this product. They

contain important information about safety, usage

and disposal. Before using the product, please

familiarise yourself with all the operating and safety

instructions. Use the product only as described and

for the range of applications speciﬁed. Please also

pass these operating instructions on to any future

owner.

Intended use

This appliance is designed for screwing and drilling

into wood, plastic and metal. The appliance may

only be used as described and for the speciﬁed ap-

plication areas. Any other usage of or modiﬁcation

to the appliance is deemed to be improper and

carries a signiﬁcant risk of accidents. The manufac-

turer accepts no responsibility for damage caused

by incorrect use of the appliance. This appliance is

not intended for commercial use.

Features

Speed selector

Bit holder (magnetic)

Rotational direction switch/lock

ON/OFF switch/speed control

Belt clip

Battery charge level button

Battery display LED

Battery pack*

Release button for the battery pack

LED work light

Chuck

Torque selection ring

High-speed charger*

Red charge control LED

Green charge control LED

Package contents

1 cordless drill PABS 20-Li D5

1 bit PH2 50 mm

1 bit PH1 50 mm

1 carrying case

1 set of operating instructions

Technical data

Cordless drill: PABS 20-Li D5

Rated voltage 20 V (DC)

Rated idle speed 1st gear: n

0

0–400 rpm

2nd gear: n

0

0–1400 rpm

Chuck clamping

range

max. Ø 13 mm

Max. drill diameter Steel: 13 mm

Wood: 30 mm

Battery: PAP 20 A1*

Type: LITHIUM-ION

Rated voltage 20 V

(DC)

Capacity 2 Ah

Cells 5

High-speed battery charger: PLG 20 A1*

INPUT:

Rated voltage 230–240 V ∼, 50 Hz

(AC)

Rated power

consumption 65 W

Fuse (internal) 3.15 A

T3.15A

OUTPUT:

Rated voltage 21.5 V

(DC)

Rated current 2.4 A

Charging time approx. 60min

Protection class II /

(double insulation)

* BATTERY AND CHARGER ARE NOT SUPPLIED

IB_331803_PABS20-LiD5_LB7.indb 2 25.02.20 15:16

PABS 20-Li D5

GB

│

CY

│

3 ■

Noise emission value:

Noise measurement value determined in accordance

with EN62841. The A-rated noise level of the

power tool is typically:

Sound pressure level: L

pA

= 68.5 dB (A)

Uncertainty K: K

PA

= 3 dB

Sound power level: L

WA

= 79.5 dB (A)

Uncertainty K: K

WA

= 3 dB

Vibration emission value:

Total vibration values (vector total of three directions)

determined in accordance with EN 62841:

Screws: Vibration emission value

a

h

: 0.601 m/s

2

Uncertainty K = 1.5 m/s

2

Drilling in metal: Vibration emission value

a

h,D

: 1.070 m/s

2

Uncertainty K = 1.5 m/s

2

NOTE

► The vibration emission values and the noise

emission values given in these instructions

have been measured in accordance with

a standardised test procedure and can be

used for comparison of the power tool with

another tool.

► The speciﬁed total vibration values and the

noise emission values can also be used to

make a provisional load estimate.

WARNING!

► Depending on the manner in which the power

tool is being used, and in particular the kind

of workpiece being worked, the vibration and

noise emission values can deviate from the

values given in these instructions during actual

use of the power tool.

WARNING!

► Try to keep the vibration loads as low as

possible. Measures to reduce the vibration

load are, e.g. wearing gloves and limiting the

working time. Wherein all states of operation

must be included (e.g. times when the power

tool is switched oﬀ and times where the power

tool is switched on but running without load).

General power

tool safety warnings

WARNING!

► Read all safety warnings, instructions,

illustrations and speciﬁcations provided

with this power tool. Failure to follow all

instructions listed below may result in electric

shock, ﬁre and/or serious injury.

Save all warnings and instructions for future

reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-

operated (cordless) power tool.

1. Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmo-

spheres, such as in the presence of ﬂammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

2. Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools. Unmodiﬁed plugs

and matching outlets will reduce risk of electric

shock.

IB_331803_PABS20-LiD5_LB7.indb 3 25.02.20 15:16

PABS 20-Li D5

■ 4

│

GB

│

CY

b) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

e) When working outdoors with an electrical

power tool, always use extension cords that

are also suitable for use outdoors. Use of a

cord suitable for outdoor use reduces the risk

of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD re-

duces the risk of electric shock.

3. Personal safety

a) Stay alert, watch what you are doing and

use common sense when operating a power

tool. Do not use a power tool while you are

tired or under the inﬂuence of drugs, alcohol

or medication. A moment of inattention while

operating a power tool may result in serious

personal injury.

b) Use

personal protective equipment. Always

wear eye protection. Protective equipment such

as a dust mask, non-skid safety shoes, hard hat

or hearing protection used for appropriate condi-

tions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools

with your ﬁnger on the switch or energising

power tools that have the switch on invites

accidents.

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool

may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away

from moving parts. Loose clothes, jewellery or

long hair can be caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used.

Use of dust collection can reduce dust-related

hazards.

h) Do not allow yourself to get lulled into a false

sense of security and do not ignore the safety

rules for power tools, even if you are familiar

with the power tool after repeated use.

A careless action can cause severe injury within

a fraction of a second.

4. Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at

the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and oﬀ. Any power tool that can-

not be controlled with the switch is dangerous

and must be repaired.

c) Disconnect the plug from the power source

and/or remove the battery pack, if detachable,

from the power tool before making any adjust-

ments, changing accessories, or storing power

tools. Such preventive safety measures reduce

the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are

dangerous in the hands of untrained users.

IB_331803_PABS20-LiD5_LB7.indb 4 25.02.20 15:16

PABS 20-Li D5

GB

│

CY

│

5 ■

e) Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition

that may aﬀect the power tool’s operation.

If damaged, have the power tool repaired

before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

g) Use the power tool, accessories and tool bits,

etc., in accordance with these instructions,

taking into account the working conditions

and the work to be performed. Use of the

power tool for operations diﬀerent from those

intended could result in a hazardous situation.

h) Keep handles and grasping surfaces dry,

clean and free from oil and grease. Slippery

handles and grasping surfaces do not allow

for safe handling and control of the tool in un-

expected situations.

5. Use and handling of the cordless

electrical power tool

a) Charge a rechargeable battery using only

the charger recommended by the manufac-

turer. There is a risk of ﬁre if a battery charger

designed for a particular type of battery is used

with other batteries.

b) Only the rechargeable battery units supplied

are to be used with an electrical power tool.

The use of other rechargeable battery units may

lead to the danger of injury or ﬁre.

c) When they are not being used, store re-

chargeable battery units away from paper-

clips, coins, keys, nails, screws or other small

metal objects that could cause the contacts

to be bridged. Short-circuiting the contacts of

a rechargeable battery unit may result in heat

damage or ﬁre.

d) Fluids may leak out of rechargeable battery

units if they are misused. If this happens,

avoid contact with the ﬂuid. If contact occurs,

ﬂush the aﬀected area with water. Seek addi-

tional medical help if any of the ﬂuid gets into

your eyes. Escaping battery ﬂuid may cause

skin irritation or burns.

e) Do not use damaged or modiﬁed batteries.

Damaged or modiﬁed batteries may behave

unexpectedly and cause ﬁres, explosions or

pose a risk of injury.

f) Do not expose a battery to ﬁre or excessively

high temperatures. Fire or temperatures in

excess of 130°C (265°F) can cause an

explosion.

g) Follow all instructions regarding charging

and never charge the battery or the cordless

tool outside of the temperature range given in

the operating instructions. Incorrect charging

or charging outside of the permissible tempera-

ture range can destroy the battery and increase

the risk of ﬁre.

CAUTION! RISK OF EXPLOSION!

Never charge non-rechargeable

batteries.

Protect the rechargeable battery

from heat (for example, from

continuous exposure to sunlight),

ﬁre, water and moisture. There is a

risk of explosion.

6. Service

a) Have your power tool serviced by a qualiﬁed

repair person using only identical replace-

ment parts. This will ensure that the safety of

the power tool is maintained.

b) Never try to repair damaged batteries.

Batteries should only be maintained by the

manufacturer or an approved customer service

centre.

IB_331803_PABS20-LiD5_LB7.indb 5 25.02.20 15:16

PABS 20-Li D5

■ 6

│

GB

│

CY

Safety instructions for drills

Safety instructions for all work.

■ Hold the appliance by the insulated gripping

surfaces when performing work where the

screws or insert tool may hit hidden power

lines. If the accessory tool or a screw comes

into contact with a live wire, this may make

exposed metal parts of the power tool live and

could give the operator an electric shock.

■ Collect any dust that is produced; for example,

using a vacuum cleaner.

Safety information for using long drill bits

■ Do not use a higher rotational speed than

the maximum permissible speed. At higher

speeds, the drill bit can bend slightly if allowed

to turn freely without being in contact with the

workpiece and this can lead to injuries.

■ Always start drilling at a low speed and with

the drill bit in contact with the workpiece. At

higher speeds, the drill bit can bend slightly if

allowed to turn freely without being in contact

with the workpiece and this can lead to injuries.

■ Do not exert excessive pressure and only

apply pressure along the length of the drill bit

(no lateral pressure). Drill bits can bend and

break which can lead to a loss of control and

injuries.

Original accessories/attachments

■ Only use the accessories and additional equip-

ment that are speciﬁed in the operating instruc-

tions and are compatible with the appliance.

WARNING!

■ Do not use any accessories that are not

recommended by PARKSIDE. This can lead to

electric shock and ﬁre.

Safety guidelines for battery

chargers

■ This appliance may be used by

children aged 8 years and above

and by persons with limited physical,

sensory or mental capabilities or

lack of experience and knowledge,

provided that they are under super-

vision or have been told how to use

the appliance safely and are aware

of the potential risks. Do not allow

children to use the appliance as a

toy. Cleaning and user maintenance

tasks may not be carried out by

children unless they are supervised.

The charger is suitable for

indoor use only.

WARNING!

■ To avoid potential risks, damaged mains

cables should be replaced by the manufac-

turer, their customer service department or

a similarly qualiﬁed person.

CAUTION!

♦ This charger can only charge the following

batteries: PAP 20 A1/PAP 20 A2/PAP20

A3.

♦ An up-to-date battery compatibility list can

be found at www.Lidl.de/Akku.

IB_331803_PABS20-LiD5_LB7.indb 6 25.02.20 15:16

PABS 20-Li D5

GB

│

CY

│

7 ■

Before use

Charging the battery pack (see ﬁg. A)

CAUTION!

► Always unplug the appliance before you

remove the battery pack

from or connect it

to the charger.

NOTE

► Never charge the battery pack at an ambient

temperature of below 10°C or above 40°C.

If a lithium-ion battery is to be stored for an

extended period, the charge level should be

checked regularly. The optimum charge level

is between 50% and 80%. The storage climate

should be cool and dry and the ambient tem-

perature should be between 0°C and 50°C.

♦ Connect the battery pack to the high-speed

battery charger (see ﬁg. A).

♦ Insert the power plug into the socket. The control

LED

lights up red to indicate that the appli-

ance is charging.

♦ The green control LED

indicates that the

charging process is complete and the battery

pack is ready for use.

♦ Push the battery pack

into the appliance

(see ﬁg. B).

Inserting/removing the battery pack

Attaching the battery pack

♦ Move the rotation direction switch

to the mid-

dle position (lock, see ﬁg. C). Slide the battery

pack

into the handle until it clicks into place

(see ﬁg. B).

Removing the battery pack

♦ Press the release button

and remove the

battery pack (see ﬁg.D).

Checking the battery charge level

♦ To check the battery status, press the battery

charge level button (see ﬁg. E).

The status/remaining charge will be shown

on the battery display LED as follows:

GREEN/RED/ORANGE = maximum charge/

performance

RED/ORANGE = medium charge/performance

RED = low charge – charge the battery

Changing tools

Your cordless screwdriver has a fully automatic

spindle lock .

When the motor is stopped, the power train locks

so that the chuck

can be opened by turning it

. After you have inserted the desired tool and

clamped it by turning the drill chuck , you can

resume working immediately (see ﬁg. F). The spin-

dle lock is released automatically when the motor

is started (by pressing the ON/OFF switch ).

Torque selection ring/drill setting

You can set the torque using the torque selection

ring (see ﬁg. G).

♦ Select a low level for small screws or soft

materials.

♦ Select a high level for large screws, hard

materials or removing screws.

♦ Select the drill setting for drilling work by ad-

justing the torque selection ring

to the

position

(see ﬁg. H).

IB_331803_PABS20-LiD5_LB7.indb 7 25.02.20 15:16

PABS 20-Li D5

■ 8

│

GB

│

CY

2-speed gearbox

CAUTION!

► Operate the speed selector switch

only

when the appliance is at a standstill. Other-

wise the appliance could be damaged.

In ﬁrst gear (speed selector switch

in posi-

tion 1) (see ﬁg. I)

you can reach a speed of approx. 400 rpm and a

high torque. This setting is suitable for all screwing

jobs.

In second gear (speed selector switch

in

position 2) (see ﬁg. J)

you can reach a speed of approx. 1400 rpm for

carrying out drilling work

Use

Switching on/oﬀ

Switching on

♦ Press and hold the ON/OFF switch

to start

up the appliance (see ﬁg. K).

The LED working light lights up when the

ON/OFF switch is pressed lightly or fully.

This provides illumination of the work area in

poor lighting conditions.

Switching oﬀ

♦ Release the ON/OFF switch

to switch oﬀ

the appliance.

Setting the rotational speed

The ON/OFF switch has a variable speed

control. Press the ON/OFF switch lightly for a

low speed. Increasing the pressure increases the

speed (see ﬁg. K).

NOTE

►

The integrated motor brake ensures that the

appliance stops quickly.

Changing the direction of rotation

♦ Change the direction of rotation by pressing

the rotation direction switch

towards the left

or right (see ﬁg. L).

Tips and tricks

Tip! How to do things correctly.

♦ Before operation, check whether the screw or

drill insert is correctly ﬁtted, i.e. centred in the

drill chuck.

♦ Screw bits are labelled according to their di-

mensions and their shape. If you are uncertain,

always check ﬁrst whether the bit ﬁts tightly in

the screw head without any play.

Torque

♦ Smaller screws/bits can be damaged if you

set too high a torque or too high a speed.

Hard screw joints (in metal)

♦ Particularly high torques occur, e.g. in metal

screw joints made using drive sockets.

Select a low rotational speed.

Soft screw joints (e.g. in soft wood)

♦ Here, too, use a low speed to avoid damaging

the wood surface when it comes into contact

with the metal screw head. Use a countersink.

When drilling in wood, metal and other

materials, observe the following

♦ Use a high speed for drill bits with a small

diameter and a low speed for drill bits with

a large diameter.

♦ Select a low speed for hard materials and

a high speed for soft materials.

♦ Secure or fasten the workpiece in a clamp

or vice (if possible).

♦ Mark the spot where you want to drill with a

punch or nail. Select a low rotational speed

when you start drilling.

♦ Pull the rotating drill bit out of the hole several

times to remove dust and chips and clear the

hole.

IB_331803_PABS20-LiD5_LB7.indb 8 25.02.20 15:16

PABS 20-Li D5

GB

│

CY

│

9 ■

Drilling in metal

♦ Use a metal drill (HSS). For optimum results,

cool the drill bit with cutting oil. Metal drill bits

can also be used to drill into plastics. Pre-drill

with a 3 mm diameter drill bit and then increase

the size until the desired hole diameter is

achieved.

Drilling in wood

♦ Use a wood drill with a lathe centre; for deep

holes, use an auger bit; for large-diameter

holes, use a Forstner bit. Small screws can be

screwed directly into soft wood without predrill-

ing.

Maintenance and cleaning

WARNING! RISK OF INJURY! Always

switch the appliance oﬀ and remove

the battery before carrying out any

work on the appliance.

The cordless screwdriver is maintenance-free.

■ The appliance must always be kept clean,

dry and free from oil or grease.

■ Never allow liquids to get into the tool.

■ Use a dry cloth to clean the housing. Never use

petrol, solvents or cleansers which can damage

plastic.

■ If a lithium-ion battery is to be stored for an

extended period, the charge level should be

checked regularly. The optimum charge level is

between 50% and 80%. The optimum storage

environment is cool and dry.

NOTE

► Replacement parts that are not listed (such as

batteries, switches) can be ordered via our

Service Hotline.

Kompernass Handels GmbH

warranty

Dear Customer,

This appliance has a 3-year warranty valid from

the date of purchase. If this product has any faults,

you, the buyer, have certain statutory rights. Your

statutory rights are not restricted in any way by the

warranty described below.

Warranty conditions

The warranty period starts on the date of purchase.

Please keep your receipt in a safe place. This will

be required as proof of purchase.

If any material or manufacturing fault occurs within

three years of the date of purchase of the product,

we will either repair or replace the product for you

or refund the purchase price (at our discretion).

This warranty service requires that you present the

defective appliance and the proof of purchase (re-

ceipt) within the three-year warranty period, along

with a brief written description of the fault and of

when it occurred.

If the defect is covered by the warranty, your prod-

uct will either be repaired or replaced by us. The

repair or replacement of a product does not signify

the beginning of a new warranty period.

Warranty period and statutory claims for

defects

The warranty period is not prolonged by repairs

eﬀected under the warranty. This also applies to

replaced and repaired components. Any damage

and defects present at the time of purchase must

be reported immediately after unpacking. Repairs

carried out after expiry of the warranty period shall

be subject to a fee.

IB_331803_PABS20-LiD5_LB7.indb 9 25.02.20 15:16

PABS 20-Li D5

■ 10

│

GB

│

CY

Scope of the warranty

This appliance has been manufactured in accord-

ance with strict quality guidelines and inspected

meticulously prior to delivery.

The warranty covers material faults or production

faults. The warranty does not extend to product

parts subject to normal wear and tear or to fragile

parts which could be considered as consumable

parts such as switches or parts made of glass.

The warranty does not apply if the product has

been damaged, improperly used or improper-

ly maintained. The directions in the operating

instructions for the product regarding proper use

of the product are to be strictly followed. Uses

and actions that are discouraged in the operating

instructions or which are warned against must be

avoided.

This product is intended solely for private use and

not for commercial purposes. The warranty shall

be deemed void in cases of misuse or improper

handling, use of force and modiﬁcations / repairs

which have not been carried out by one of our

authorised Service centres.

The warranty period does

not apply to

■ Normal reduction of the battery capacity

overtime

■ Commercial use of the product

■ Damage to or alteration of the product by the

customer

■ Non-compliance with safety and maintenance

instructions, operating errors

■ Damage caused by natural hazards

Warranty claim procedure

To ensure quick processing of your case, please

observe the following instructions:

■ Please have the till receipt and the item number

(e.g.IAN12345) available as proof of purchase.

■ You will ﬁnd the item number on the type plate

on the product, an engraving on the product,

on the front page of the operating instructions

(below left) or on the sticker on the rear or

bottom of the product.

■ If functional or other defects occur, please

contact the service department listed either by

telephone or by e-mail.

■ You can return a defective product to us free of

charge to the service address that will be pro-

vided to you. Ensure that you enclose the proof

of purchase (till receipt) and information about

what the defect is and when it occurred.

You can download these instructions

along with many other manuals,

product videos and installation

software at www.lidl-service.com.

This QR code will take you directly

to the Lidl service page (www.lidl-service.com)

where you can open your operating instructions by

entering the item number (IAN) 123456.

IB_331803_PABS20-LiD5_LB7.indb 10 25.02.20 15:16

PABS 20-Li D5

GB

│

CY

│

11 ■

Service

WARNING!

► Have your appliances repaired by the

Service Centre or a trained electrician,

and use only original spare parts. This will

ensure that the safety of the appliance is

maintained.

► Always ensure that the power plug or

the mains cable is replaced only by the

manufacturer of the appliance or by an

approved customer service provider. This

will ensure that the safety of the appliance is

maintained.

Service Great Britain

Tel.: 0800 404 7657

E-Mail: [email protected]

CY

Service Cyprus

Tel.: 8009 4409

E-Mail: [email protected]

IAN 331803_1907

Importer

Please note that the following address is not the

service address. Please use the service address

provided in the operating instructions.

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

GERMANY

www.kompernass.com

Disposal

The packaging is made from environ-

mentally friendly material which can be

disposed of at your local recycling

plant.

Do not dispose of power tools in

your normal domestic waste!

European Directive 2012/19/EU requires that

worn-out power tools be collected separately and

recycled in an environmentally compatible manner.

Do not dispose of batteries in your

normal household waste!

Defective or worn-out rechargeable batteries must

be recycled according to Directive 2006/66/

EC. Take the battery pack and/or tool to a nearby

collection facility.

Please consult your local authorities regarding

suitable disposal of worn-out power tools/battery

packs.

Dispose of the packaging in an

environmentally friendly manner.

Note the labelling on the packaging

and separate the packaging material

components for disposal if necessary. The packag-

ing material is labelled with abbreviations (a) and

numbers (b) with the following meanings:

1–7: plastics, 20–22: paper and cardboard,

80–98: composites.

Your local community or municipal

authorities can provide information on

how to dispose of the worn-out product.

IB_331803_PABS20-LiD5_LB7.indb 11 25.02.20 15:16

PABS 20-Li D5

■ 12

│

GB

│

CY

Translation of the original Conformity Declaration

We, KOMPERNASS HANDELS GMBH, document oﬃcer: Mr Semi Uguzlu, BURGSTR. 21,

44867 BOCHUM, GERMANY, hereby declare that this product complies with the following standards,

normative documents and EC directives:

Machinery Directive

(2006/42/EC)

EC Low Voltage Directive

(2014/35/EU) (charger only)

EMC (Electromagnetic Compatibility)

(2014/30/EU)

RoHS Directive

(2011/65/EU)*

* The manufacturer bears the full responsibility for compliance with this conformity declaration.

The object of the declaration described above complies with the requirements of the Directive 2011/65/

EU of the European Parliament and Council of 8 June 2011 on the limitations of use of certain danger-

ous substances in electrical and electronic appliances.

Applied harmonised standards:

EN 62841-1:2015

EN 62841-2-1:2018

EN 55014-1:2017

EN 55014-2:2015

EN 60335-2-29:2004/A2:2010

EN 60335-1:2012/A13:2017

EN 62233:2008

EN 61000-3-2:2014

EN 61000-3-3:2013

EN 50581:2012

Type/appliance designation: Cordless drill PABS 20-Li D5

Year of manufacture: 11 - 2019

Serial number: IAN 331803_1907

Bochum, 13/11/2019

Semi Uguzlu

- Quality Manager -

We reserve the right to make technical changes in the sense of further product development.

IB_331803_PABS20-LiD5_LB7.indb 12 25.02.20 15:16

PABS 20-Li D5

GB

│

CY

│

13 ■

Ordering a replacement battery

If you want to order a replacement battery for your appliance, you can do so easily via the Internet on

www.kompernass.com or by telephone.

Due to limited stocks, this item may sell out in a relatively short time.

NOTE

► Online ordering of replacement parts might not be possible in some countries. In this case, please

contact the Service hotline.

Telephone ordering

Service Great Britain

Tel.: 0800 404 7657

E-Mail: [email protected]

CY

Service Cyprus

Tel.: 8009 4409

E-Mail: [email protected]

To ensure fast processing of your order, have the article number of your appliance to hand (e.g. IAN

331803) in case of questions. The article number can be found on the type plate or the title page of

these instructions.

IB_331803_PABS20-LiD5_LB7.indb 13 25.02.20 15:16

PABS 20-Li D5

■ 14

│

GB

│

CY

IB_331803_PABS20-LiD5_LB7.indb 14 25.02.20 15:16

Pagina se încarcă ...

Parkside PABS 20-Li D5 Translation Of The Original Instructions

Acest manual este potrivit și pentru

Parkside PABS 20-Li D5 Translation Of The Original Instructions

Lucrări conexe

Alte documente