Kawasaki K-MS 1400 Original Instructions Manual

Marca: Kawasaki

Model: K-MS 1400

Tip: Original Instructions Manual

Translation of the original

instructions

Sliding mitre saw

K-MS 1400

Art.-Nr.: 603.010.530

Table of contents

1. Description of symbols

2. Machine components

3. Accessories

4. Machine components (A1/4)

5. Proper usage

6. General Safety instructions

7. Special safety instructions

8. Before starting

9. Transport

10. Assembly

11. Working with the crosscut and mitre saw

12. Maintenance and care

13. Technical data

14. Environmental protection

1. Safety instructions and warnings

The equipment complies with the safety

regulations required for electrical equipment.

Read through the instructions for use before

starting up the equipment.

Improper use can lead to personal injury and

property damage. Persons, who are not familiar

with the instructions, may not operate the

equipment.

Keep the instructions for use in safe custody.

Children and youths are not permitted to operate

the equipment.

2. Description of symbols

Pay attention to all the signs and symbols shown

in these instructions and on your tool. Make a

note of these signs and symbols. If you interpret

the signs and symbols correctly, your work with

the machine will be safer and better.

Important.

Do not look straight into the laser.

Laser class II

Important.

Read the instructions for use before

starting the machine.

Wear safety goggles.

Wear ear protection.

Wear good quality, strong gloves.

Always use breathing apparatus

when machining materials which

generate dust.

3. Accessories

This CROSSCUT AND MITRE SAW WITH DRAG

FUNCTION is supplied with the following

accessories:

• Saw blade with 36 teeth (tted)

• Chip bag

• Clamping device

• Side support (2x)

• Hexagonal wrench

4. Machine components (A1-4)

1. Laser

2. ON/OFF switch for the laser light

3. Laser cover

4. Laser adjustment

5. Sawing arm

6. Release knob

7. Control lever

8. Carry handle

6. General safety instructions

• Keep your work area clean and well lit to prevent

accidents.

• Don’t use electric devices close to ammable

liquids or gasses or in wet or damp environments.

If you fail to observe this, there is a danger

of re or explosion.

• Never leave the device running unattended.

• Never use the device when you are tired or lack

concentration or if your reactions are impaired

due to consumption of alcohol or medication.

Lack of attention can lead to serious injury.

• Keep the tools clean and in good working order

in order to be able to work better and safer.

• Don’t wear bulky clothing or jewellery.

• Make sure you can stand stably and have shoes

that won’t slip.

• Use a head cover if you have long hair.

• Loose clothing, jewellery, and long hair can

become entangled in moving parts.

• Always wear safety goggles.

• Wear a dust mask when working with materials

that produce dust.

• Wear ear protection if a lot of noise is produced.

• Persons using the machines must not be

distracted.

This could cause one to lose control

over the tool.

• Don’t use any device that has a faulty on/o

switch. An electric tool that can no longer be

switched on or o is dangerous and must be

repaired.

9. Top safety hood (xed)

10. Clamping device

11. Lock for clamping device

12. Moving safety hood

13. Safety hood control arm

14. Cover for saw blade screws

15. Chip bag

16. Vertical angle lock

17. Vertical angle scale

18 . Fence

19. Hexagonal wrench

20. Mitre bench

21. Mitre scale

22. Bench insert (slotted plate)

23. ON/OFF switch for machine

24. Mitre angle lock

25. Spindle locking button

26. Connection for dust extractor

27. Guide rails

28. Drag lock

29. Setting screw for cutting depth

30. Depth stop

31. Lock nut

32. Setting screw for sawing head angle

33. Stopper for 90° lock

34. Release lever for saw blade guard

35. Side supports (2x)

36. Positioning holes for side supports

(2 pairs)

5. Proper usage

This machine is designed for crosscutting wood

and plastic in sizes commensurate with the

machine size.

It is not suitable for cutting rewood.

Use only saw blades which are suitable for the

machine. Do not use cutting discs.

The manufacture assumes no liability whatsoever

for improper use or if the machine has been

tampered with.

Give equal attention to the safety instructions,

assembly and operating instructions as well as

prevailing accident preventions regulations.

• Always switch the device on before coming into

contact with the material.

• Remove keys and adjusting tools before

switching on the device.

• Never overload the machine. If the speed drops,

unload the machine or switch it o. You will

work safer and better with the appropriate

electric tool in a specic area of application.

• Stop the workpiece from turning, for example

with a clamping device or a vice. Don’t work

on any workpiece that is too small to clamp in

place. If you hold the workpiece with your hand,

then you can’t operate the tool safely.

• Keep electric tools out of the reach of children.

• Only use accessories recommended by the

manufacturer.

• The mains voltage must correspond to the

information on the machine’s type plate.

• Avoid body contact to grounded elements, e.g.

pipes, radiators, stoves, and refrigerators, to

prevent an electric shock.

• Never carry the device by the cable. Only pull

the cable from the receptacle with the plug.

Protect the cable from oil, heat, and sharp

edges. Damaged cables can cause an electric

shock.

• Check the device and power cable for damage

before starting work.

• When plugging in the power plug, make sure

that the operating switch is not located in

position.

• Only use approved extension cables when using

the device outside.

• When using a cable drum, unwind it entirely in

order to prevent the cable from heating up. The

minimum wire gauge is 1.5 mm

• When working outside, the receptacle must be

equipped with a residual current circuit-breaker.

• Pull the plug when you are not using the device

or making adjustments.

• Always guide the cable away from the back of

the tool.

7. Special safety instructions

• Never use the crosscut mitre saw for cutting

materials other than those specied by the

manufacturer.

• Only use the saw if the guards are in the correct

positions and if the saw is in good condition

and has been serviced correctly.

• Ensure that the equipment for swinging the arm

on mitre saws is securely fastened.

• The oor around the machine must be at, clean

and clear of loose particles such as chips and

o-cuts.

• Ensure that there is reasonable lighting in the

workplace or room.

• The operator must have received adequate

training in the use, setting and operation of the

machine.

• Ensure that you only use spacing discs and

spindle rings which are suitable for the purpose

specied by the manufacturer.

• The laser must not be replaced by a laser of a

dierent type. Repairs may only be carried out by

the manufacturer of the laser or an authorised

representative.

• Damaged or deformed saw blades must not be

used.

• Replace worn table inserts.

• Use only saw blades which are recommended by

the manufacturer and comply with EN 847-1.

• Do not use saw blades made of high speed steel.

• The crosscut mitre saw must be connected to a

dust extraction system for sawing wood.

• Always position the workpiece securely on the

machine surface to prevent the workpiece

moving.

• Use an additional support for long workpieces

(for example a table or saw stool) to prevent the

machine from tipping over. Do not ask other

people to hold the workpiece.

• Place the machine on a strong, at working area

before use.

• Check whether the moving parts of the machine

are in perfect working order and that no parts

are damaged.

• Check the direction of rotation of the motor and

saw blade.

• Replace defective saw blades immediately.

• Keep your hands, ngers and arms away from

the rotating saw blade.

• Do not reach behind the stop rail near the saw

blade, the distance between your hand and the

rotating saw blade is too small for this.

• Only saw one workpiece at a time. Workpieces

placed on top of each other or side by side cannot

be clamped correctly and they may jam the

saw blade or move relative to each other.

• Keep the cutting track free of obstacles both at

the top and bottom.

• Do not saw workpieces which contain nails or

similar foreign bodies.

• Always work to the side of the saw blade.

• Ensure that the o-cuts can be removed to

the side of the saw blade so that they do not

become caught in the saw blade.

• Always switch o the machine and pull the plug

to rectify problems or remove jammed pieces of

wood. Only then can you remove the jammed

workpiece.

• Do not overload the machine so that it comes to

a standstill.

• Protect the saw blade from impacts and shocks.

Do not exert any lateral pressure on it.

• Caution. The saw blade will continue to turn

after the machine has been switched o.

• The saw blade will become very hot during use.

Do not touch it until it has cooled down.

• Select the appropriate saw blade for the material

that you wish to saw.

8. Before starting

• Assemble the machine in a stable position, in

other works on a workbench, a sub-frame or the

like. Secure it if you wish to use the machine on

a stationary basis.

• Before starting the machine, check that all

covers and safety equipment are correctly tted.

• The saw blade must be able to run freely.

• Check all the moving parts to ensure that they

move easily.

• Before you connect the machine, check the

information on the rating plate against the

mains data.

9. Transport

Only lift the mitre saw if the sawing arm is locked

in its lowered position, the saw is switched o

and the mains plus has been pulled.

The saw may only be lifted using the carry handle

(8) or the external cast parts. Do not hold the saw

by the safety hood or control lever (7) to lift it. (B1)

10. Assembly

ASSEMBLY ON THE WORKBENCH

There are holes on the foot of the saw to make it

easy to install it on a workbench.

Secure the saw on a straight, at workbench. (B2)

Insert suitable screws (not supplied) through the

installation holes in the foot of the saw for this

purpose.

NOTE: If necessary you can also secure the saw to

a piece of plywood with a minimum thickness of

13 mm. The plywood may be secured on a

working sarea using clamps or transported to

another workplace and secured there.

CAUTION. The fastening surface must be at. An

uneven surface may result in the saw blade

jamming or imprecise cutting.

FITTING THE SIDE SUPPORT (B3)

Place the two guide rods into the side supports

and secure them.

The chip bag (15) will t on the connect for the

extractor (26). To ensure ecient operation, you

should empty the chip bag when it is half full. (B4)

ADJUST BENCH PERPENDICULAR TO THE SAW

BLADE

Pull the mains cable out of the socket.

Press the sawing arm (5) into the lowered position

and press the release knob (6) to lock the sawing

arm in its transport position. (B5)

Release the mitre angle lock (24).

Turn the mitre bench (20) until the pointer points

to 0°. (B6)

Tighten the mitre angle lock (24).

Release the vertical angle lock (16) and set the

sawing arm (5) to a vertical angle of 0° (in other

words the saw blade is at an angle of 90° to the

mitre bench). Tighten the vertical angle lock (16).

(B7)

Hold an angle bracket against the bench (20) and

the at part of the saw blade. (B8)

NOTE: The angle bracket must touch the at part

of the saw blade, not its teeth.

Turn the saw blade by hand and check the correct

alignment between the saw blade and the bench

at several points.

The edge of the angle bracket should run parallel

to the saw blade.

If the saw blade is not parallel to the angle

bracket, make the adjustment as follows:

• Undo the lock nuts on the sawing head vertical

angle (32) using a wrench or an adjustable

wrench. (B9)

• Undo the lock nut which is secured by the 0°

vertical angle setting screw (33) using a wrench

or an adjustable wrench. Release the

vertical angle lock (16). (B10)

• Adjust the screw on the sawing head vertical

angle (32) with a screwdriver by turning it

clockwise and anti-clockwise so that the saw

blade is on the 90° angle bracket.

• Undo the screw which holds the pointer on the

vertical angle scale (17) and set the pointer so

that it points to zero. Tighten the screw again.

• Tighten the vertical angle lock (16) and the lock

nut to secure the sawing head vertical angle (32).

NOTE: The above procedure can also be used to

check the angle of the saw blade relative to the

bench for a vertical angle of 45°. The 45° vertical

angle setting screw (32) is on the other side of the

sawing arm.

SWITCHING ON THE LASER LINE

Switch on the ON/OFF switch for the laser light (2).

(B11)

ADJUSTING THE CUTTING DEPTH

Release the swing head lock (6) by pulling it. The

sawing head will swing upwards. (B12)

Set the required cutting depth using the setting

screw (29). (B13)

Secure the stop screw using the lock nut (31).

(B14)

SIDE SUPPORTS

Long pieces of wood can be supported using the

side supports (35). (B16)

There are two positioning holes (36) on each side

of the bench for the side supports.

The side supports must be completely locked in

position before a workpiece is placed on them.

11. Working with the crosscut and mitre

saw

WARNINGS

- Do not look directly into the laser beam. Never

direct the laser beam at people or objects other

than the workpiece.

- Do not deliberately point the laser beam at

people.

- Only point the laser beam at insensitive

workpieces with a dull surface. Wood or rough

surfaces are ideal for this. Shiny, reective

surfaces are not suitable for using a laser since the

laser beam could be directed at the user by the

reective surfaces.

- Always switch o the laser when you have

nished work at the ON/OFF switch for the laser

light (2). Only switch on the laser beam if there is

a workpiece on the mitre saw bench.

- Mark the cutting line on the workpiece.

- Adjust the mitre and vertical angle for the cut as

required.

NOTE: To make a cut to the left of the saw blade,

direct the left laser line along the pencil mark. To

make a cut to the right of the saw blade, direct

the right laser line along the pencil mark. (B17)

1. NORMAL SAWING

1) Insert the mains plug into the socket. Switch on

the ON/OFF switch for the laser light (2). (B11)

2) Clamp the workpiece and align the saw blade

along the mark on the workpiece using the laser

line and then switch on the motor.

3) Press the release switch (34). (B18)

4) Lower the sawing arm.

5) Press the ON/OFF switch (23). (B19)

6) When the saw blade has reached its maximum

speed (after around 2 seconds), lower it slowly

through the workpiece. (B20)

Press the sawing head backwards away from you

as far as possible. (B21)

Switch o the ON/OFF switch for the laser light

(2) after you have completed the cut.

7) Raise the sawing arm (5) and remove the saw

dust on the laser using a soft brush.

NOTE: Wear safety goggles and breathing

apparatus to remove the saw dust.

2. CROSS CUTS (WITHOUT DRAG FUNCTION)

(B22)

The drag function is not required for sawing

narrow pieces of wood. Always make sure in

these cases that the drag lock (28) is secure so

that the sawing arm cannot slide backwards and

forwards.

1) A cross cut is made across the grain of the

workpiece.

A 90° cross cut is carried out by setting the

mitre bench to 0°. For mitre cross cuts the bench

must be set to an angle other than zero.

2) Release the mitre angle lock (24).

Turn the mitre bench (21) until the pointer points

to the required angle.

Tighten the mitre angle lock (24) again.

WARNING. The mitre angle lock must be

tightened before the cut is carried out. Otherwise

the bench can move during sawing which can

result in serious injuries.

Place the workpiece at on the bench with one

edge securely against the guide rail (18). If the

board is curved place the side curving outwards

against the guide rail (18). If the side which curves

inwards is placed against the guide rail, the board

may snap and jam the saw blade.

3) When sawing long boards, support the end of

the board level with the saw bench using the side

supports (35), a roller frame or a worktop.

4) If possible use the clamping device (10) to

clamp the workpiece securely.

The clamping device (10) can be removed after

the lock (11) has been undone and then tted

on the other side of the bench. When using the

clamping device ensure that its lock is secure.

Before you switch on the saw carry out a dry run

of the sawing process to ensure that no problems

occur. (B23)

5) Hold the control lever (7) securely and press

the release switch (23). Wait until the saw blade

has reached maximum speed.

Press the release switch (34) and slowly lower the

saw blade into the workpiece and through the

workpiece.

Let go of the release switch (23), wait until the

saw blade has reached a standstill and only raise

the saw blade again at this point. Do not remove

the workpiece until the saw blade has reached a

standstill.

3. CROSS CUTS (WITH DRAG FUNCTION) (B24)

For sawing wide workpieces the drag lock (28)

must rst be released.

Pull out the locking knob (6), raise the sawing arm

(5) to its highest point and slide it towards you.

Press the release switch (34) and slowly lower the

saw blade on to the workpiece. Move the sawing

head away from you as far as possible as you do

so.

Press the release switch (34) and slowly lower the

saw blade on to the workpiece.

Slide the saw away from you as you do so.

Let go of the release switch (23), wait until the

saw blade has reached a standstill and only

raise the saw blade again at this point. Do not

remove the workpiece until the saw has reached

a complete standstill.

4. VERTICAL ANGLE CUTS (B25)

A vertical angle cut is carried out across the grain

of the workpiece with the saw blade at a certain

angle to the guide rail and the mitre bench. The

mitre bench must be set to 0° and the saw blade

must be set to an angle between 0° and 45°.

Use the drag function for sawing wide

workpieces.

Repeat steps 28 and 29 in point 3 Cross cuts (with

drag function).

Release the vertical angle lock (16) and move the

sawing arm (5) to the left to the required vertical

angle (between 0° and 45°). Tighten the vertical

angle lock (16).

Repeat steps 30 and 31 from point 15 Adjusting

the cutting depth.

5. COMBINED MITRE CUTS

The mitre angle and the vertical angle must both

be set for combined mitre cuts.

This process is used, for example, to make picture

frames, for cutting strips and for making crates

using angled side walls and also for roof trusses.

Always test the cut rst using a piece of waste

wood before you cut the actual material.

Use the drag function for sawing wide

workpieces.

12. Maintenance and care

CAUTION.

- Never attempt to use a saw blade which exceeds

the maximum specied size for the saw. The saw

blade could come into contact with the safety

hood.

- Never use saw blades which are excessively thick

which will prevent contact between the external

saw blade washer and the attened parts of the

spindle. This means that the saw blade cannot

be secured correctly to the spindle with the saw

blade screw.

- Do not use the saw to cut metal or masonry.

- Please note that the spacers and spindle rings

which may be required are suitable for the spindle

and the saw blade you wish to use.

- The mains cable must be disconnected from the

mains supply.

1. CHANGE SAW BLADES

1) Press the control lever (7) downwards and pull

the release knob (6) to release the sawing arm (5).

The release knob can be locked in the released

position by turning it. Move the sawing arm (5)

into its highest position.

2) Remove the Philips screw which secures the

saw blade screw cover (14). (B26)

3) Pull the moving safety hood (12) downwards

and then swing it upwards together with the saw

blade screw cover (14).

4) If the moving safety hood (12) is above the top,

xed safety hood (9), the saw blade screw is

accessible.

5) Hold the moving safety hood (12) in its top

position and press the spindle locking button (25).

Turn the saw blade until the spindle locks.

6) Remove the saw blade screw using the

hexagonal wrench (19). (Turn the wrench

clockwise since the saw blade screw has a left-

handed thread).(B27)

7) Remove the external washer and the saw

blade.

Apply a drop of oil to the internal and external

washers at the places in which it is in contact

with the saw blade.

Secure the new saw blade on the spindle. Ensure

that the internal washer is located behind the

saw blade.

machine.

3. GENERAL INSPECTION

Check at regular intervals that all the securing

screws a rmly tightened. Pay special attention to

the external ange. The screws may come loose

over time due to vibration.

Check the machine’s mains cable and all the

extension cables you use for signs of damage at

regular intervals. Have the mains cable replaced

by an authorised outlet.

Replace damaged extension cables.

4. LUBRICATION

After extended use the oil in the machine’s

gearbox must be changed. Contact an authorised

outlet for this purpose.

13. Technical data

This machine has double insulation. It has two

independent insulations to protect you from

electric shocks.

Voltage: 230 V ~/50 Hz

Rating: 1400 W

Idling speed: 5500 rpm

Saw blade: Ø 255 mm x Ø 30 mm

Angle of mitre bench: -45°/0°/+45°

0° x 0° : 120 mm x 55 mm

0° x 45°: 120 mm x 30 mm

45° x 0°: 83 mm x 55 mm

45°x 45°(L): 83 mm x 30 mm

min: 100 mm x 10 mm

DETAILS OF NOISE AND VIBRATION

DEVELOPMENT

A-rated noise level L

: 97,5 dB(A)

A-rated noise rating L

: 106,8 dB(A)

K= 3 dB(A)

Vibrations 2.5 m/s

K=1.5 m/s

CAUTION. Always t the saw blade so that the

teeth and the arrows printed on the side of the

saw blade point downwards so that the saw

blade will rotate in the correct direction. There is

also an arrow on the top safety hood to show the

direction of rotation of the saw blade. (B28)

8) Fit the external saw blade washer again.

Press the spindle locking button (25) and t the

saw blade screw again.

9) Tighten the screw with the hexagonal wrench

(19) (turn it anti-clockwise).

Move the moving bottom safety hood (12) and

the saw blade screw cover (14) into the correct

position and tighten the securing screws.

Check whether the safety hood functions

correctly and covers the saw blade when the

sawing arm is lowered.

Connect the saw to the power supply and start

the saw blade to check whether it functions

correctly.

2. MAINTENANCE

- Keep the ventilation openings on the machine

clean and free of blockages at all times.

- Check regularly whether dust or foreign particles

have got into the ventilation grille next to the

motor and in the area around the release switch.

Remove the accumulated dust with a soft brush.

Wear safety goggles when cleaning these areas.

- Grease all moving parts at regular intervals.

- Clean the machine’s housing, if necessary, using

a soft damp cloth. A mild detergent may be used

but never use alcohol, petrol or other aggressive

cleaning product.

- Never use discharging agent to clean plastic

parts.

CAUTION. Ensure that no water gets into the

Use only the accessories and spare parts

recommended by the manufacturer. If the device

suers a failure despite our quality controls and

your care, have repair work carried out only by an

authorised electrician.

14. Environmental protection

End of life electrical equipment must

not be placed in household waste.

Please take it to a return point. Find out

about your nearest return point from

your council or sales outlet.

Original Konformitätserklärung

Matrix GmbH

Postauer Str. 26

D-84109 Wörth/Isar

Germany

Fax: +49 (0) 8702/45338 98

E-Mail: [email protected]

erklärt folgende Konformität gemäss

EU-Richtline und Normen für den Artikel

hereby declares the following

conformity under the EU Directive and

standards for the following article

déclare la conformité suivante selon la

directive UE et les normes pour l’article

prohlašuje následující shodu podle

smernice EU a norem pro výrobek

EN 55014-1; EN 55014-2; EN 61000-3-11; EN 61000-3-3; EN 61029-1; EN 61029-2-9; EN 60825-1

deklaruje, ze produkt jest zgodny

z nastepujacymi dyrektywami UE i

normami

Wörth/Isar, den 25.02.2015

Art.-Nr.: 603.010.530

Autorisierte Person zur Aufbewahrung der technischen Dokumente:

Matrix GmbH

Postauer Str. 26

D-84109 Wörth / Isar

Germany

dichiara la seguente conformità secondo

le direttive e le normative UE per

l‘articolo

prehlasuje nasledujúcu zhodu podla

smernice EU a noriem pre výrobok

az EU-irányelv és a vonatkozó

szabványok szerinti következo

megfeleloségi nyilatkozatot teszi a

termékre

SLO

izjavlja sledeco skladnost z

EU-direktivo in normami za artikel

ovime izjavljuje da postoji sukladnost

prema EU-smjernica i normama za

sljedece artikle

Zug-, Kapp - und Gehrungssäge / K-MS 1400

2006/42/EC

R&TTED 1999/5/EC

2000/14/EC

95/54/EC

73/23/EWG

2006/95/EC

93/68/EEC

2004/108/EC

2011/65/EU

2002/96/EC

verklaart hierbij dat het volgende artikel

voldoet aan de daarop betrekking

hebbende EG-richtlijnen en normen

declară următoarea conformitate

corespunzător directivelor şi normelor

UE pentru articolul

Joachim Lichtl (Geschäftsführer)

FIN

vakuuttaa täten, että seuraava tuote

täyttää ala esitetyt EU-direktiivit ja

standardit

deklareerib vastavuse järgnevatele EL

direktiividele ja normidele

GARANTIE

Dieses Gerät ist ein Qualitätserzeugnis. Es wurde unter Beachtung der

derzeitigen technischen Erkenntnisse konstruiert und unter Verwendung eines

üblichen guten Materials sorgfältig gebaut.

Die Garantiezeit beträgt 24 Monate und beginnt mit dem Zeitpunkt der

Übergabe, der durch Kassenbon, Rechnung oder Lieferschein nachzuweisen

ist. Innerhalb der Garantiezeit werden alle Funktionsfehler durch unseren

Kundendienst beseitigt, die nachweisbar, trotz vorsichtsmäßiger Behandlung

entsprechend unserer Bedienungsanleitung auf Materialfehler zurückzuführen

sind.

Die Garantie erfolgt in der Weise, dass mangelhafte Teile nach unserer Wahl

unentgeltlich instandgesetzt oder durch einwandfreie Teile ersetzt werden.

Ersetzte Teile gehen in unser Eigentum über. Durch die Instandsetzung oder

Ersatz einzelner Teile wird die Garantiezeit weder verlängert noch wird neue

Garantiezeit für das Gerät in Gang gesetzt. Für eingebaute Ersatzteile läuft keine

eigene Garantiefrist. Wir übernehmen keine Garantie für Schäden und Mängel an

Geräten oder deren Teile, die durch übermäßige Beanspruchung, unsachgemäße

Behandlung und Wartung auftreten. Das gilt auch bei Nichtbeachtung der

Bedienungsanleitung sowie Einbau von Ersatz- und Zubehörteile, die nicht in

unserem Programm aufgeführt sind. Beim Eingreifen oder Veränderungen an

dem Gerät durch Personen, die hierzu nicht von uns ermächtigt sind, erlischt der

Garantieanspruch.

Schäden, die auf unsachgemäße Handhabung, Überlastung oder auf

natürliche Abnutzung zurückzuführen sind, bleiben von der Garantie

ausgeschlossen.

Der Hersteller haftet nicht für Folgeschäden. Schäden, die durch

Herstelleroder Materialfehler entstanden sind, werden durch Reparatur- oder

Ersatzlieferung unentgeltlich behoben.

Vorrausetzung ist, dass das Gerät unzerlegt und vollständig mit Kauf- und

Garantienachweis übergeben wird.

Verwenden Sie im Garantiefall ausschließlich die Originalverpackung.

So garantieren wir Ihnen eine reibungslose und schnelle

Garantieabwicklung.

Bitte senden Sie die Geräte “frei Haus” ein oder fordern Sie einen Freeway-

Aufkleber an. Unfreie Einsendungen können wir leider nicht annehmen!

Die Garantie bezieht sich nicht auf die Teile, die durch eine natürliche

Abnutzung verschlissen werden.

Bei Garantieanspruch, Störungen, Ersatzteil- oder Zubehörbedarf wenden

Sie sich bitte an die hier aufgeführte Kundendienstzentrale:

Änderungen vorbehalten.

GARANTIE

Cet appareil est un produit de qualité. Il a été conçu selon les connaissances

techniques actuelles et construit soigneusement en utilisant une bonne

matière première courante.

La durée de garantie est de 24 mois et commence à courir au moment de

la remise qui doit être attestée en présentant le ticket de caisse, la facture

ou le bon de livraison. Pendant la période de garantie, toutes les anomalies

fonctionnelles sont éliminées par notre service après-vente résultant, malgré

une manipulation correcte conformément à notre notice d‘utilisation, d‘un

vice de matériel.

La garantie se déroule de façon à ce que les pièces défectueuses soient

réparées gratuitement ou remplacées par des pièces impeccables, selon

notre choix. Les pièces remplacées deviennent notre propriété. La réparation

ou le remplacement de certaines pièces n‘entraîne aucune prolongation de

la durée de garantie ni une nouvelle garantie pour l‘appareil. Les pièces de

rechange montées n‘ont pas de durée de garantie propre. Nous n‘accordons

aucune garantie pour des dommages et défauts sur les appareils ou leurs

pièces découlant d‘une trop forte sollicitation, d‘une manipulation non

conforme ou d‘un manque d‘entretien.

Cela vaut également en cas de non-respect de la notice d‘utilisation ainsi

que pour le montage de pièces de rechange et d‘accessoires qui ne gurent

pas dans notre gamme. En cas d‘interventions ou de modications de

l‘appareil eectuées par des personnes que nous n‘avons pas mandatées,

le droit à la garantie devient caduc.Les dommages résultant d‘une

manipulation non conforme, d‘une surcharge ou d‘une usure normale sont

exclus de la garantie.

Il sera remédié sans frais aux dommages dus à un défaut de fabrication ou

à un défaut sur le matériau par une réparation ou par le remplacement de

l‘appareil.

A condition que l‘appareil soit rapporté non démonté et complet avec la

preuve d‘achat et le bon de garantie.

Pour faire fonctionner la garantie, utilisez exclusivement l‘emballage

original. Nous vous assurons ainsi un fonctionnement rapide et sans

problème de la garantie.

Veuillez envoyer les appareils „ franco usine „ ou demandez un autocollant

Freeway. Nous ne pouvons malheureusement pas accepter les expéditions

non aranchies !

La garantie ne s‘étend pas au pièces usées en raison d‘une usure naturelle.

En cas de demande de garantie, de pannes, de demande de pièces de

rechanges ou d‘accessoires, veuillez vous adresser à la centrale du service

après-vente ci-dessous :

Sous réserve de modications.

Matrix GmbH Service

Postauer Str. 26

D – 84109 Wörth/Isar

Tel.: +49 (0) 1806/841090

Fax: +49 (0) 8702/45338 98

e-mail: service@matrix-direct.net

WARRANTY

This appliance is a quality product. It was designed in compliance with

current technical standards and made carefully using normal, good quality

materials.

The warranty period is 24 months and commences on the date of purchase,

which can be veried by the receipt, invoice or delivery note. During this

warranty period all functional errors, which, despite the careful treatment

described in our operating manual, are veriably due to material aws, will

be rectied by our after-sales service sta.

The warranty takes the form that defective parts will be repaired or replaced

with perfect parts free of charge at our discretion. Replaced parts will

become our property. Repair work or the replacement of individual parts

will not extend the warranty period nor will it result in a new warranty period

being commenced for the appliance. No separate warranty period will

commence for spare parts that may be tted. We cannot oer a warranty for

damage and defects on appliances or their parts caused by the use of excessive

force, improper treatment and servicing.

This also applies for failures to comply with the operating manual and the

installation of spare and accessory parts that are not included in our range

of products. In the event of interference with or modications to the

appliance by unauthorised persons, the warranty will be rendered void.

Damages that are attributable to improper handling, over loading, or

natural wear and tear are excluded from the guarantee.

Damages caused by the manufacturer or by a material defect will be

corrected at no charge by repair or by providing spare parts.

The prerequisite is that the equipment is handed over assembled, and

complete with the proof of sale and guarantee.

For a guarantee claim, only use the original packaging.

That way, we can guarantee quick and smooth guarantee processing.

Please send us the appliances post-paid or request a Freeway sticker.

Unfortunately we will be unable to accept appliances that are not postpaid.

The warranty does not cover parts that are subject to natural wear and tear.

If you wish to make a warranty claim, report faults or order spare parts or

accessories, please contact the after-sales centre below:

Subject to change without prior notice.

ZÁRUKA

Tento prístroj je výrobok vynikajúcej kvality. Bol skonštruovaný s využitím

terajších technických poznatkov a bol pozorne zhotovený za použitia zvycajného

dobrého materiálu.

Zárucná lehota je 24 mesiacov a zacína casom odovzdania, ktorý je

preukázatelný pokladnicným blokom, faktúrou alebo dodacím listom. Pocas

zárucnej lehoty náš zárucný servis odstráni všetky chyby funkcnosti, ktoré

možno preukázatelne, napriek pozornému zaobchádzaniu v súlade s našim

návodom na obsluhu, vyvodit z chýb materiálu. Záruka sa vykoná tak, že chybné

casti budú podla našej volby bezplatne opravené alebo nahradené bezchybnými

castami. Nahradené casti sa stanú našim vlastníctvom. Opravou alebo výmenou

jednotlivých castí sa zárucná lehota nepredlži, ani nezacne bežat nová zárucná

lehota. Pre vstavané náhradné casti nebeží žiadna vlastná zárucná lehota.

Nepreberieme záruku za škody a chyby prístrojov alebo ich castí, ktoré vzniknú

nadmerným zatažením, neodborným zaobchádzaním a údržbou.

To platí aj pri nerešpektovaní návodu na obsluhu, ako aj pri vmontovaní

náhradných castí a príslušenstva, ktoré nie sú uvedené v našom programe. Pri

zásahoch alebo zmenách prístroja osobami, ktoré od nás nie sú na to oprávnené,

zanikne nárok na záruku.

Poškodbe nastale med transportom, neupoštevanje navodil za uporabo in

montažo, nepooblaščen poseg v stroj, preobremenitev stroja ali naravna

obraba materiala ne spadajo v garancijsko popravilo. Vse pomanjkljivosti

in okvare na izdelku, ki so nastale zaradi napake na materialu ali napake

proizvajalca, bomo brezplačno odpravili v roku 45 dni. Če izdelek ne bo

popravljen v 45 dneh, ga bomo zamenjali z novim. Garancijski rok bo

podaljšan za toliko dni, kolikor dni je trajalo popravilo izdelka. Garancija

velja ob predložitvi računa in potrjenega garancijskega lista z datumom

prodaje, žigom in podpisom prodajalca. Izdelek, ki je dan v popravilo mora

biti v originalni embalaži, opremljen z identikacijsko nalepko in nalepko s

serijsko številko, ki ne sme biti poškodovana. Servisiranje izdelka in rezervni

deli so zagotovljeni za dobo 6 let. Prosím pošlite prístroje „vyplatene

do domu“ alebo požiadajte o Freewaynálepku. Neofrankované zásielky

bohužial nemôžeme prijat!

Záruka sa nevztahuje na casti, ktoré nefungujú prirodzeným

opotrebovaním. Pri garancných nárokoch, poruchách, potrebe náhradných

dielov alebo príslušenstva sa prosím obrátte na tu uvedenú centrálu služieb

zákazníkom:

Salvo modicaciones.

GARANTIE

Dit apparaat is een kwaliteitsproduct. Het is ontworpen conform de actuele

technische kennis en zorgvuldig vervaardigd uit voor het doel geschikt

materialen.

De garantieperiode bedraagt 24 maanden en gaat in op het moment van de

aevering, die vermeld moet staan op de kassabon, rekening of het

aeveringsbewijs.

Binnen de garantieperiode lost de klantenservice alle storingen

op die, ondanks behandeling van het apparaat volgens de voorschriften

zoals die vermeld staan in de handleiding, worden veroorzaakt door

materiaalfouten.

In een dergelijk geval zullen defecte onderdelen kostenloos worden gerepareerd

of vervangen door correct functionerende onderdelen, e.e.a. ter beoordeling

van ons. Vervangen onderdelen worden ons eigendom. Door reparatie

of vervanging van onderdelen wordt de garantieperiode noch verlengd, noch

gaat een nieuwe garantieperiode voor het apparaat in. Ingebouwde

vervangingsonderdelen zijn niet onderhavig aan een eigen garantietermijn. Wij

kunnen geen garantie verstrekken voor schade en gebreken aan apparaten

of de onderdelen hiervan, ontstaan ten gevolge van overmatig gebruik, een

foutieve behandeling resp. verkeerd onderhoud.

Dit is ook van toepassing wanneer de gebruikshandleiding niet wordt

opgevolgd, alsmede wanneer vervangingsonderdelen en accessoires worden

aangebracht die niet in ons leveringsprogramma vermeld staan. Bij

aanpassingen van of wijzigingen aan het apparaat door personen, die hiertoe

niet door ons gemachtigd zijn, vervalt het recht op garantie. Defecten die het

gevolg zijn van onoordeelkundig gebruik, overbelasting of normale slijtage,

vallen niet onder de garantie.

Defecten die het gevolg zijn van productie- of materiaalfouten, worden

kosteloos verholpen; indien vereist ontvangt u een soortgelijk apparaat.

Voorwaarde voor garantie is dat het apparaat in niet gedemonteerde

toestand en compleet tezamen met aankoopbewijs en de garantiekaart

wordt overhandigd.

Gebruik in geval van aanspraak op garantie uitsluitend de originele

verpakking.

Alleen dan kunnen wij u een probleemloze en snelle garantieafwikkeling

garanderen.

Stuur de apparaten franco op of informeer naar een Freeway-sticker. Niet

gefrankeerde zendingen kunnen wij helaas niet aannemen!

De garantie geldt niet voor onderdelen, die door gebruikelijke slijtage

versleten zijn.

Neem contact op met de klantenservice wanneer u een beroep doet op

garantie, bij storingen, wanneer u vervangingsonderdelen of accessoires

nodig heeft:

Artrace Int.

Tradepartner and aftersales oce:

Postadres: Berliozstraat 2 - 6815 HG Arnhem (NL)

Bezoekadres: Overmaat 36 - 6831 AH Arnhem (NL) ( Lieferadresse )

T: +31(0) 6 53 443 673 F: +31(0) 847 297 061

KvK nr (CoC nr) : 53143620 Btw nr (Vat nr) : NL117832303B02

ZARUKA

Zakoupený prístroj je velmi kvalitním produktem. Pri jeho konstrukci byly

zohledneny veškeré technické poznatky a pri výrobe byly použity bežné

kvalitní materiály.

Zárucní doba ciní 24 mesícu a zacíná okamžikem predání zakoupeného

prístroje, které musí být prokázáno predložením faktury, pokladního

dokladu nebo dodacího listu. Behem zárucní doby naše zákaznická služba

odstraní veškeré funkcní závady, které vznikly i pres opatrné zacházení

podle našich provozních pokynu jako dusledek materiální vady. Vadné

soucástky budou dle našeho uvážení bezplatne opraveny nebo vymeneny

za nové. Nahrazené cásti precházejí do našeho vlastnictví. Oprava nebo

výmena nejsou duvodem pro prodloužení ci obnovení zárucní doby

prístroje. Na vymenené soucástky neposkytujeme žádnou samostatnou

zárucní dobu. Neprebíráme záruku za škody a nedostatky zpusobené

pretežováním,neodborným zacházením ci chybnou údržbou prístroje.

Totéž platí pri nedodržování pokynu návodu k obsluze a instalaci náhradních

dílu i príslušenství neuvedených v našem programu. Pri zásahu nebo

zmene prístroje námi nepovolanými osobami nárok na záruku zaniká.

Škody vzniklé neodborným zacházením, přetížením nebo přirozeným

opotřebením jsou ze záruky vyloučeny.

Poškození, jejichž příčinou je materiálová nebo výrobní vada, budou

bezplatně opraveny nebo obdržíte náhradní přístroj.

Předpokladem k tomu je předání nerozloženého přístroje se záručním

listem a dokladem o zakoupení.

V případě uplatňování záruky použijte originální obal.

Jen tak bude vaše záruka bez problémů a rychle vyřízena.

Prístroj zašlete vyplacene nebo si vyžádejte nálepku Freeway.

Nevyplacené zásilky nebudeme moci prevzít!

Záruka se nevztahuje na prirozene opotrebené cásti.

Pri uplatnování záruky, poruchách, objednávání náhradních dílu nebo

príslušenství se obracejte na uvedené stredisko zákaznické služby:

EASY CZ s.r.o.

Výpadová 1335

153 00 Praha 5 – Radotín

Tel/fax: +420 257 910 204

GSM: +420 606 624 241 (Stanislav Mach)

E-Mail: [email protected]

SZAVATOSSÁG

Ez a készülék minõségi termék. Szerkesztése a jelenlegi mûszaki ismeretek

gyelembe vételével történt, és azt a szokásos jó minõségû anyagok

felhasználásával, gondos munkával készítettük.

A szavatossági idõtartam 24 hónap, mely az átadás idõpontjában kezdõdik,

s amit pénztárblokkal, számlával, vagy szállítólevéllel kell igazolni. A

szavatossági idõ alatt minden olyan mûködési hibát ügyfélszolgálatunk

szüntet meg, mely bizonyíthatóan, a használati utasításnak megfelelõ

óvatossággal történõ használat ellenére anyaghibára vezethetõ vissza.

A szavatosság érvényesítése úgy történik, hogy a hibás alkatrészt saját

döntésünk alapján vagy díjmentesen megjavítjuk, vagy pedig kifogástalan

alkatrésszel helyettesítjük. A kicserélt alkatrészek a tulajdonunkba kerülnek.

Az egyes alkatrészek javítása, vagy cseréje révén a szavatossági idõ

nem hosszabbodik meg és a készülékre vonatkozóan sem állapítunk meg

új szavatossági idõt. A beépített alkatrészekre nem vonatkozik saját szavatossági

határidõ. A készülékek és alkatrészeik olyan hibáiért és hiányosságaiért,

melyek túlzott igénybevétel, szakszerûtlen használat és karbantartás

miatt következnek be, nem vállalunk szavatosságot.

Ez érvényes a kezelési utasítás gyelmen kívül hagyására, valamint az

olyan alkatrészek és tartozékok beépítésének esetére is, melyek nem

szerepelnek programunkban. Ha olyan személyek nyúlnak bele a készülékbe,

vagy módosítják azt, akiket erre nem hatalmaztunk fel, a szavatossági

igény megszûnik. Az olyan károk esetében, melyek szakszerűtlen

használatra, túlterhelésre vagy természetes elhasználódásra vezethetők

vissza, a szavatosság nem érvényes.

A gyártási, vagy anyaghibára visszavezethető károkat javítással, vcagy

cserekészülék biztosításával térítésmentesen szüntetjük meg.

Ennek az a feltétele, hogy a teljes készüléket szétszedés nélkül a számlával

és a szavatossági jeggyel együtt szállítja be.

Garanciális esetben kizárólag az eredeti csomagolást használja.

A szavatossági eset problémamentes és gyors lebonyolítását így tudjuk

garantálni.

Kérjük, küldjék be a készüléket „frei Haus“ (bérmentesítve), vagy

igényeljenek hozzá egy Freeway-matricát (elõre megzetett postaköltség).

A nem bérmentesített küldeményeket sajnos nem tudjuk elfogadni!

A szavatosság nem vonatkozik olyan alkatrészekre, melyek a természetes

elhasználódás következtében vannak kitéve kopásnak.

Szavatossági igény, hibák, valamint alkatrészek és tartozékok iránti

igény esetén forduljanak az alább feltüntetett ügyfélszolgálati központhoz.

A változtatások jogát fenntartjuk.

GARANŢIE

Acest aparat este rezultatul unui proces de asigurare a calităţii. A fost

construit cu grijă, prin respectarea cunoştinţelor tehnice din acel moment şi

prin utilizarea unor materiale bune.

Perioada de garanţie este de 24 de luni şi începe din momentul preluării

aparatului, fapt dovedit prin bonul de casă, chitanţă sau factură. Pe durata

perioadei de garanţie, atelierul nostru de service autorizat va remedia toate

defectele de funcţionare a căror cauză este materialul defectuos, în cazul

unei utilizări conform acestor instrucţiuni de utilizare.

Garanţia constă în repararea pieselor defecte sau înlocuirea acestora cu altele

noi, la alegerea noastră. Piesele înlocuite vor deveni proprietatea noastră.

Prin repunerea în funcţiune sau înlocuirea unor componente individuale,

perioada de garanţie nu se prelungeşte şi nici nu va începe o nouă perioadă

de garanţie pentru întregul aparat. Pentru piesele de schimb montate nu

există o perioadă de garanţie proprie. Noi nu oferim garanţie pentru defecte

sau probleme la aparat sau componente apărute din cauza suprasolicitării,

deservirii şi întreţinerii necorespunzătoare. Acest lucru este valabil şi pentru

nerespectarea acestor instrucţiuni de utilizare, cât şi pentru montarea de

piese de schimb şi accesorii care nu sunt prezente în programul nostru. În

cazul lucrărilor sau modicărilor efectuate de către persoane care nu sunt

autorizate să efectueze aşa ceva, se pierde dreptul de garanţie. Defecţiunile

a căror cauză este o utilizare necorespunzătoare, suprasarcină sau uzură

naturală, nu sunt acoperite de garanţie.

Fabricantul nu este responsabil pentru daunele care apar în acest fel.

Defecţiunile care apar din vina fabricantului sau a materialelor, vor 

remediate prin reparare sau înlocuire.

Premisa pentru acest lucru este ca aparatul să e asamblat şi să e predat

complet cu chitanţă şi certicat de garanţie.

În cazul solicitării garanţiei, utilizaţi numai ambalajul original.

În acest fel, vă asigurăm de o desfăşurare a garanţiei rapidă şi fără

probleme.

Vă rugăm să ne trimiteţi aparatul pe cheltuiala dvs. Acceptăm numai

expedierile pentru care nu trebuie să plătim.

Garanţia se referă numai la componentele care nu se uzează în mod natural

prin folosire.

Pentru cereri de garanţie, defecţiuni, necesar de piese de schimb sau

accesorii, adresaţi-vă centrului de relaţii cu clienţii prezentat mai jos:

Ne rezervăm dreptul asupra modicărilor.

GARANCIJA

SLO

Aparat je visoko kakovosten izdelek. Konstruiran je ob upoštevanju sedanjih

tehnicnih spoznanj in skrbno narejen z uporabo obicajnih dobrih materialov.

Garancijska doba znaša 24 mesecev in zacne teci z dnem prodaje, velja pa ob

predložitvi racuna in potrjenega garancijskega lista z datumom prodaje, žigom

in podpisom prodajalca. V garancijski dobi bomo preko naše servisne službe

odpravili vse pomanjkljivosti in okvare, ki bodo nastale na izdelku pri normalni

rabi izdelka in ob upoštevanju navodil za uporabo.

Garancija velja v primeru pomanjkljive izvedbe, napake na materialu

ali v delovanju in v tem primeru bomo izdelek brezplacno popravili ali

zamenjali. Zamenjani deli ostanejo v naši lasti. V casu popravila ali zamenjave

posameznega dela se garancijska doba podaljša za cas, ko je izdelek v popravilu.

Za vgrajene nadomestne dele ne velja poseben garancijski rok. Za poškodbe

in okvare na izdelku ali delih, ki nastanejo zaradi prekomerne obremenitve,

nestrokovnega posega in vzdrževanja ne priznamo garancije.

Garancija ne velja tudi za neupoštevanje navodil za montažo in uporabo kot

tudi za vgradnjo nadomestnih delov in pribora, ki niso dobavljivi v našem

prodajnem programu. Pravica iz garancije preneha, ce v izdelek posegajo ali

ga spreminjajo osebe, ki jih proizvajalec ni pooblastil za odpravo okvar in

pomanjkljivosti.

Poškodbe nastale med transportom, neupoštevanje navodil za uporabo in

montažo, nepooblaščen poseg v stroj, preobremenitev stroja ali naravna

obraba materiala ne spadajo v garancijsko popravilo. Vse pomanjkljivosti

in okvare na izdelku, ki so nastale zaradi napake na materialu ali napake

proizvajalca, bomo brezplačno odpravili v roku 45 dni. Če izdelek ne bo

popravljen v 45 dneh, ga bomo zamenjali z novim.

Garancijski rok bo podaljšan za toliko dni, kolikor dni je trajalo popravilo

izdelka.

Garancija velja ob predložitvi računa in potrjenega garancijskega lista

z datumom prodaje, žigom in podpisom prodajalca. Izdelek, ki je dan v

popravilo mora biti v originalni embalaži, opremljen z identikacijsko

nalepko in nalepko s serijsko številko, ki ne sme biti poškodovana.

Servisiranje izdelka in rezervni deli so zagotovljeni za dobo 6 let.

Garancijsko popravilo ne velja za naravno obrabo materiala.

Za pravico iz garancije, motnje, potrebo po rezervnih delih ali opremi se

obrnite na našo servisno službo:

Spremembe pridržane.

Takuu

FIN

Tämä laite on laatutuote. Se on suunniteltu voimassa olevien teknisten

standardien mukaisesti ja valmistettu huolellisesti käyttämällä tavallisia,

hyvälaatuisia materiaaleja.

Takuuaika on 24 kuukautta, ja se alkaa ostopäivästä, joka voidaan todistaa

kuitilla, laskulla tai luovutustodistuksella. Takuuaikana huoltotakuupalvelumme

korjaa kaikki toiminnalliset viat, jotka ovat todistettavasti aiheutuneet

materiaalivioista ja siitä huolimatta, että käyttöohjeissa annettuja käsittelyohjeita

on noudatettu huolellisesti.

Takuuhuollossa vialliset osat korjataan tai vaihdetaan veloituksetta uusiin

virheettömiin osiin harkintamme mukaan. Vaihdetut osat siirtyvät meidän

omaisuudeksemme. Korjaustoimenpiteet tai yksittäisten osien vaihtaminen eivät

pidennä takuuaikaa, eivätkä ne aloita uutta takuuaikaa laitteelle. Vaihdetuille

varaosille ei ala erillistä takuuaikaa. Takuu ei kata sellaisia laitteille tai niiden

osille aiheutuneita vahinkoja ja vikoja, joiden syynä on liiallinen voimankäyttö,

väärinkäyttö tai vääränlainen huolto.

Takuu ei kata myöskään vikoja, jotka ovat aiheutuneet käyttöohjeiden

noudattamatta jättämisestä, eikä vikoja, jotka ovat aiheutuneet sellaisten

vara- tai lisäosien asentamisesta, jotka eivät kuulu tuotevalikoimaamme. Jos

valtuuttamaton henkilö tekee laitteeseen muutoksia, takuu mitätöityy.

Takuun ulkopuolelle jäävät sellaiset vahingot, jotka ovat seurausta

vääränlaisesta käsittelystä, ylikuormituksesta tai luonnollisesta kulumisesta.

Valmistajasta tai materiaalivioista johtuvat vahingot korjataan veloituksetta

tai tarjoamalla vaihto-osat.

Edellytyksenä on, että laite luovutetaan kokonaisena ja sen mukana

toimitetaan myynti- ja takuutodistukset.

Käytä takuuvaateissa aina alkuperäistä pakkausta.

Näin voimme taata nopean ja sujuvan takuukäsittelyn.

Lähetä laitteet postimaksu suoritettuna tai pyydä Freeway-tarraa.

Emme valitettavasti voi ottaa vastaan laitteita, joiden postimaksua ei ole

maksettu.

Takuu ei kata normaaleja käytössä kuluvia osia.

Jos haluat tehdä takuuvaateen tai vikailmoituksen tai tilata varaosia

tai lisävarusteita, ota yhteyttä alla mainittuun myynninjälkeiseen

asiakaspalveluun.

Muutokset mahdollisia ilman ennakkoilmoitusta.

GARANTII

Käesolev seade on kvaliteettoode. See on kavandatud kooskõlas kehtivate

tehniliste standarditega ja selle valmistamiseks on kasutatud standardseid

kvaliteetseid materjale.

Garantiiaeg on 24 kuud ja jõustub alates ostukuupäevast, mida tõendatakse

ostukviitungi, arve või üleandmisaktiga. Garantiiperioodi ajal kõrvaldab meie

müügijärgne teenindus seadme mis tahes funktsionaalse rikke, mis on tekkinud

materjalivigade tõttu, vaatamata seadme nõuetekohasele käsitlemisele, nagu

kirjeldatud meie kasutusjuhendis.

Garantii raames parandame defektsed osad või asendame need töökorras

osadega tasuta oma äranägemise järgi. Väljavahetatud osad jäävad meie

omandisse.

Remonditööd või üksikosade vahetamine ei pikenda garantiiperioodi ja selle

tulemusena ei anta seadmele uut garantiid. Sisseehitatud varuosadele ei kehti

eraldi garantiid. Me ei saa anda garantiid seadmete või osade kahjustustele või

defektidele, mis on põhjustatud ülemäärase jõu rakendamisest seadme kallal ja

seadme ebaõigest kasutamisest või hooldamisest.

See kehtib ka kasutusjuhendi mittejärgimise korral ning varuosade ja

lisatarvikute paigaldamisel, mis ei pärine meie tootevalikust. Seadme omavolilise

muutmise korral volitamata isikute poolt kaotab garantii kehtivuse. Garantii

ei kehti kahjustuste korral, mis on tingitud seadme ebaõigest käsitlemisest,

ülekoormamisest või loomulikust kulumisest.

Tootja põhjustatud või materjalivigadest tingitud kahjustused parandatakse

või asendatakse uute varuosadega ilma selle eest tasu nõudmata.

Eelduseks on, et seade antakse üle kokkumonteeritult ja tervikuna ning

ostu- ja garantiitõendiga.

Garantiinõude esitamisel kasutage ainult originaalpakendit.

Sellisel juhul saame me tagada kiire ja sujuva garantiimenetluse. Palun

saatke meile seade, tasudes ise saatekulud või nõudke Freeway-kleebist.

Kahjuks ei saa me aktsepteerida seadmeid, mille saatmise eest ei ole tasutud.

Garantii ei laiene osadele, mis on purunenud loomuliku kulumise tõttu.

Kui te soovite esitada garantiinõude, teatada riketest või tellida varuosi

või lisatarvikuid, siis palun võtke ühendust alltoodud müügijärgse

teeninduskeskusega:

Käesolevat teavet võidakse muuta ilma ette teatamata.

ZARUKA

Zakoupeno u:

V (místo, ulice):

Jméno prodejce:

Ulice, císlo domu:

PSC, místo :

Telefon:

Datum, Podpis:

Popis závady:

GARANTIE

gekauft bei:

in (Ort, Straße):

Name d. Käufers:

Straße, Haus-Nr.:

PLZ, Ort :

Telefon:

Datum, Unterschrift:

Fehlerbeschreibung:

WARRANTY

Purchased at:

in (city, street):

Name of customer:

Street address:

Postal code, city:

Telephone:

Date, signature:

Fault description:

GARANTIE

Gekocht bij:

In (plaats, straat):

Naam v/d koper:

Straat, huisnr.:

Postcode, plaats :

Telefoon:

Datum, handtekening:

Beschrijving van de fout:

JÓTÁLLÁS

Vásárlás helye:

Cím (település, utca):

A vásárló neve:

Utca, házszám:

IRSZ, település:

Telefon:

Dátum, aláírás:

A hiba leírása:

GARANTIE

Acheté chez :

à (ville, rue) :

Nom de l’acheteur :

Rue, N° :

CP, ville :

Téléphone :

Date, signature :

Description du défaut :

GARANTIE

Gekocht bij:

In (plaats, straat):

Naam v/d koper:

Straat, huisnr.:

Postcode, plaats :

Telefoon:

Datum, handtekening:

Beschrijving van de fout:

Zug-, Kapp - und Gehrungssäge / K-MS 1400

SLO

GARANCIJA

kupljeno pri:

v (kraj, ulica):

Ime kupca:

Ulica, hišna št.:

Poštna št., kraj:

Telefon:

Datum, podpis:

Opis napake:

GARANIE

Cumpărat la data de:

Locaţia (oraş, strada):

Numele cumpărătorului:

Strada, nr.:

Cod poştal, localitatea:

Telefon:

Data, semnătura:

Descrierea defecţiunii:

FIN

TAKUU

Ostopaikka:

Kaupunki, katuosoite:

Asiakkaan nimi:

Katuosoite:

Postinumero ja kaupunki:

Puhelin:

Päivämäärä ja allekirjoitus:

Vian kuvaus:

Kawasaki K-MS 1400 Original Instructions Manual

Marca: Kawasaki

Model: K-MS 1400

Tip: Original Instructions Manual

Descărcați PDF

raport

Kawasaki K-MS 1400 Original Instructions Manual

Kawasaki K-MS 1400 Original Instructions Manual

în alte limbi

Alte documente