Ubiquiti AirFiber X AF-5G34-S45 Ghid de inițiere rapidă

Marca: Ubiquiti

Model: AirFiber X AF-5G34-S45

Categorie: Antene de rețea

Tip: Ghid de inițiere rapidă

5 GHz, 34 dBi Slant 45

Antenna for airFiber

Model: AF-5G34-S45

Introduction

Thank you for purchasing the Ubiquiti Networks® 5GHz,

34dBi Slant 45 Polarity Antenna for airFiber®. This Quick Start

Guide is designed to guide you through the installation of the

antenna. This Quick Start Guide also includes the warranty

terms and is for use with the antenna modelAF‑5G34‑S45.

Package Contents

Dish Reflector Antenna Feed Mounting Bracket

Protective

Shroud

Pole Clamps

(Qty. 2)

Stabilizer Brackets

(Qty. 2)

RF Cables

(Qty. 2)

Elevation Rod M12x180 Carriage Bolts

(Qty. 4)

M10x100 Bolts

(Qty. 2)

5 GHz, 34 dBi Slant 45

Antenna for airFiber

Model: AF-5G34-S45

M10x25 Carriage Bolts

(Qty. 3)

M4 Bolts

(Qty. 6)

Quick Start

Guide

cable and earth grounding must be used as conditions of product warranty. TOUGHCable

™

is designed for outdoor installations. It is the customer’s responsibility to follow local country

regulations, including operation within legal frequency channels, output power, and Dynamic

Frequency Selection (DFS) requirements.

Installation Requirements

• airFiber AF‑5X radio (sold separately)

• Phillips #1 screwdriver

• 16 mm wrench

• 24 mm wrench

• Mounting point:

• At least 1 m below the highest point on the structure

• For tower installations, at least 3 m below the top of

the tower

• Shielded Category 6 (or above) cabling should be used for

all wired Ethernet connections and should be grounded

through the AC ground of the PoE.

Hardware Overview

Fully Assembled Back View

Elevation Rod

Mounting Bracket

Pole Clamp

Protective Shroud

Stabilizer Brackets

Installation

Important: Handle the Dish Reflector with care.

Deformations in its shape may reduce the antenna's

effectiveness.

1. Each M4 Bolt includes a lock washer. Remove these and use

them to secure the bolts when assembling.

2. The Dish Reflector and Antenna Feed are keyed so the

Antenna Feed can only be installed in a single orientation.

Attach the Antenna Feed to the Dish Reflector in the

following steps:

a. Line up the alignment pin on the Dish Reflector with the

hole on the Antenna Feed.

b. Insert the six M4 Bolts into the Antenna Feed and Dish

Reflector.

c. Tighten the six M4 Bolts.

Important: Do NOT handle the antenna by the Antenna

Feed once the feed is attached.

3. Attach the RF Cables to the connectors labeled Chain 0 and

Chain 1 on the airFiber radio.

4. Attach the airFiber radio to the Dish Reflector.

a. Align the mounting tabs on the back of the airFiber

radio with the airFiber radio mount located below the

Antenna Feed.

b. Slide the airFiber radio down to lock it into place.

5. Attach the other end of the RF Cables to the RF connectors

on the airFiber radio in this combination: +45° to Chain0

and -45° to Chain 1. Then slide the jackets over the RF

connectors to protect them.

6. Attach the external GPS antenna (included with the airFiber

radio) to the RF connector labeled GPS on the airFiber

radio. Slide the jacket over the RF connector to protect it.

Then place the magnetic external GPS antenna on the Dish

Reflector (this is temporary; you will mount the external

GPS antenna last).

*640-00171-02*

640-00171-02

7. Attach the Protective Shroud.

a. Align the arrow on the top of the shroud with the short

hash mark on the Dish Reflector.

b. Rotate the shroud clockwise until it aligns with the long

hash mark to lock into place.

8. The Elevation Rod includes washers and nuts. Remove one

flat washer, one spring lock washer, and one nut. Use them

to secure the Elevation Rod when assembling.

9. Attach the Elevation Rod to the Mounting Bracket.

a. Insert the Elevation Rod into the Mounting Bracket.

b. Secure the Elevation Rod with the flat washer, spring

lock washer, and nut.

10. Each M12x180 Carriage Bolt includes a flat washer, spring

lock washer, and nut. Remove these and use them to

secure the bolts when assembling in step 16.

11. Insert the four M12x180 Carriage Bolts into the Mounting

Bracket.

12. Each M10x25 Carriage Bolt includes a flat washer, spring

lock washer, and nut. Remove these and use them to

secure the bolts when assembling.

13. Attach the antenna to the Mounting Bracket.

a. Insert one M10x25 Carriage Bolt into the antenna and

Elevation Rod.

b. Insert two M10x25 Carriage Bolts into the antenna and

lower section of the Mounting Bracket.

c. Secure each M10x25 Carriage Bolt with one flat washer,

one spring lock washer, and one nut.

14. Each M10x100 Bolt includes a flat washer, spring lock

washer, and nut. Remove these and use them to secure the

bolts when assembling.

15. Attach the Stabilizer Brackets to the pole just beneath the

area where the antenna will be attached.

Note: The mounting assembly can accommodate a

Ø 38 ‑ 101 mm pole.

a. Place one Stabilizer Bracket on each side of the pole.

b. Insert the two M10x100 Bolts into the Stabilizer Brackets.

c. Secure each M10x100 Bolt with one flat washer, one

spring lock washer, and one nut.

d. Tighten the nuts to approximately 50N‑m.

50 N-m

16. Attach the Mounting Bracket to the pole just above the

Stabilizer Brackets.

a. Slide a Pole Clamp over each pair of M12x180

CarriageBolts.

b. Secure each M12x180 Carriage Bolt with one flat washer,

one spring lock washer, and one nut.

17. Visually align the azimuth and elevation.

a. To adjust the azimuth, rotate the antenna while it is

supported by the Stabilizer Brackets.

b. To adjust the elevation angle, tighten or loosen the nuts

on the Elevation Rod so that the antenna is set to the

desired tilt.

c. Tighten all bolts and nuts to approximately 50N‑m or

less to avoid deforming the pole.

Nuts

Mounting the External GPS Antenna

Locate a mounting point that has a clear view to the sky, and is

above and as far away as possible from the antenna.

Note: All GPS items are included with the airFiber radio.

1. Attach the GPS antenna mount to the pole using the metal

strap, or attach it to a wall using the appropriate fasteners

(not included).

2. Place the external GPS antenna on the mount.

3. Secure the cable of the external GPS antenna to the mount

with a cable tie.

Specifications

AF‑5G34‑S45

Dimensions 1050 x 1050 x 421 mm (41.34 x 41.34 x 16.57")

Weight 13.5 kg (29.76 lb)

(Mount Included)

Frequency 5.1 ‑ 5.8 GHz

Gain 34 dBi

Max. VSWR 1.4:1

Wind Survivability 200 km/h (125 mph)

Wind Loading 1,779 N @ 200 km/h (400 lb @ 125 mph)

Polarization Dual Linear

F/B Ratio 42 dB

ETSI Specication EN 302 326 DN2

Mounting Universal Pole Mount, airFiber Radio Bracket,

and Weatherproof RF Jumpers Included

Safety Notices

1. Read, follow, and keep these instructions.

2. Heed all warnings.

3. Only use attachments/accessories specified by the manufacturer.

WARNING: Do not use this product in location that can

be submerged by water.

WARNING: Avoid using this product during an electrical

storm. There may be a remote risk of electric shock from

lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current

requirements indicated on the manufacturer’s label. Connection to a

different power source than those specified may result in improper

operation, damage to the equipment or pose a fire hazard if the

limitations are not followed.

2. There are no operator serviceable parts inside this equipment. Service

should be provided only by a qualified service technician.

Limited Warranty

UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the

product(s) furnished hereunder (the “Product(s)”) shall be free from defects

in material and workmanship for a period of one (1) year from the date

of shipment by UBIQUITI NETWORKS under normal use and operation.

UBIQUITI NETWORKS’ sole and exclusive obligation and liability under

the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion,

to repair or replace any Product that fails to conform to the above

warranty during the above warranty period. The expense of removal and

reinstallation of any Product is not included in this warranty. The warranty

period of any repaired or replaced Product shall not extend beyond its

original term.

Warranty Conditions

The above warranty does not apply if the Product:

(I) has been modified and/or altered, or an addition made thereto,

except by Ubiquiti Networks, or Ubiquiti Networks’ authorized

representatives, or as approved by Ubiquiti Networks in writing;

(II) has been painted, rebranded or physically modified in any way;

(III) has been damaged due to errors or defects in cabling;

(IV) has been subjected to misuse, abuse, negligence, abnormal

physical, electromagnetic or electrical stress, including lightning

strikes, or accident;

(V) has been damaged or impaired as a result of using third party

firmware;

(VI) has no original Ubiquiti MAC label, or is missing any other original

Ubiquiti label(s); or

(VII) has not been received by Ubiquiti within 30 days of issuance of

the RMA.

In addition, the above warranty shall apply only if: the product has been

properly installed and used at all times in accordance, and in all material

respects, with the applicable Product documentation; all Ethernet cabling

runs use CAT5 (or above), and for outdoor installations, shielded Ethernet

cabling is used, and for indoor installations, indoor cabling requirements

are followed.

Returns

No Products will be accepted for replacement or repair without obtaining

a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS

during the warranty period, and the Products being received at UBIQUITI

NETWORKS’ facility freight prepaid in accordance with the RMA process of

UBIQUITI NETWORKS. Products returned without an RMA number will not

be processed and will be returned freight collect or subject to disposal.

Information on the RMA process and obtaining an RMA number can be

found at: www.ubnt.com/support/warranty.

Disclaimer

EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI

NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA,

SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM

AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND,

EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO,

REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY,

ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY,

SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS

FOR A PARTICULAR PURPOSE AND NON‑INFRINGEMENT AND ANY

WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR

TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES.

BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR

ITS THIRD PARTY PROVIDERS CONTROL BUYER’S EQUIPMENT OR THE

TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING

THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE

SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS

AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS

FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD

PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS,

DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT

CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY

OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant

that the operation of the Products will be error‑free or that operation will

be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible

for damages or claims of any nature or description relating to system

performance, including coverage, buyer’s selection of products (including

the Products) for buyer’s application and/or failure of products (including

the Products) to meet government or regulatory requirements.

Limitation of Liability

EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL

UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR

DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES

(INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING

OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE

PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER

LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES.

Note

Some countries, states and provinces do not allow exclusions of implied

warranties or conditions, so the above exclusion may not apply to you.

You may have other rights that vary from country to country, state to

state, or province to province. Some countries, states and provinces do not

allow the exclusion or limitation of liability for incidental or consequential

damages, so the above limitation may not apply to you. EXCEPT TO

THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO

NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE

MANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY

SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations

Convention on Contracts for the International Sale of Goods shall not apply

to any transactions regarding the sale of the Products.

Compliance

RF Exposure Warning

The antenna and transmitter must be installed to provide a separation

distance from all persons and must not be located or operating in

conjunction with any other antenna or transmitter. For the specific

separation distance, refer to the Quick Start Guide for your airFiber radio

device (transmitter).

L’antenne et l’émetteur doit être installé pour fournir une distance de

séparation de toute les personnes et ne doit pas être situé ou opérant en

conjonction avec une autre antenne ou un autre émetteur. Pour la distance

spécifique de séparation, se référer au Guide de démarrage rapide pour

votre appareil airFiber radio (l’émetteur).

RoHS/WEEE Compliance Statement

English

European Directive 2002/96/EC requires that the equipment bearing

this symbol on the product and/or its packaging must not be disposed

of with unsorted municipal waste. The symbol indicates that this

product should be disposed of separately from regular household waste

streams. It is your responsibility to dispose of this and other electric and

electronic equipment via designated collection facilities appointed by the

government or local authorities. Correct disposal and recycling will help

prevent potential negative consequences to the environment and human

health. For more detailed information about the disposal of your old

equipment, please contact your local authorities, waste disposal service, or

the shop where you purchased the product.

Deutsch

Die Europäische Richtlinie 2002/96/EC verlangt, dass technische

Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit diesem

Symbol versehen ist, nicht zusammen mit unsortiertem Gemeindeabfall

entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt

von regulärem Haushaltmüll getrennt entsorgt werden sollte. Es

liegt in Ihrer Verantwortung, dieses Gerät und andere elektrische

und elektronische Geräte über die dafür zuständigen und von der

Regierung oder örtlichen Behörden dazu bestimmten Sammelstellen zu

entsorgen. Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei,

potentielle negative Folgen für Umwelt und die menschliche Gesundheit

zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer

Altgeräte benötigen, wenden Sie sich bitte an die örtlichen Behörden oder

städtischen Entsorgungsdienste oder an den Händler, bei dem Sie das

Produkt erworben haben.

Pagina se încarcă ...

Ubiquiti AirFiber X AF-5G34-S45 Ghid de inițiere rapidă

Marca: Ubiquiti

Model: AirFiber X AF-5G34-S45

Categorie: Antene de rețea

Tip: Ghid de inițiere rapidă

Descărcați PDF

raport

în alte limbi

English: Ubiquiti AirFiber X AF-5G34-S45 Quick start guide
italiano: Ubiquiti AirFiber X AF-5G34-S45 Guida Rapida

Ubiquiti AirFiber X AF-5G34-S45 Ghid de inițiere rapidă

Ubiquiti AirFiber X AF-5G34-S45 Ghid de inițiere rapidă

în alte limbi

Lucrări conexe