Ubiquiti airGateway-LR Specificație

Marca: Ubiquiti

Model: airGateway-LR

Categorie: Antene de rețea

Tip: Specificație

Acest manual este potrivit și pentru

airGateway

Indoor Access Point with

External Antenna

Model: airGateway-LR

Introduction

Thank you for purchasing the Ubiquiti Networks

™

airGateway

™

This Quick Start Guide is designed to guide you through

the installation, and show you how to access the airOS

Configuration Interface. This Quick Start Guide also includes

the warranty terms and is for use with the airGateway LR.

Package Contents

POE LAN

airGateway LR External Antenna Wall Mount Bracket

Indoor Access Point with

External Antenna

Model: airGateway-LR

Screws

(M2.9x20, Qty. 2)

Screw Anchors

(M2.9x20, Qty. 2)

Quick Start Guide

Products may be different from pictures and are subject to change without notice.

responsibility to follow local country regulations, including operation within legal frequency

channels, output power, indoor cabling requirements, and Dynamic Frequency Selection

(DFS) requirements.

Hardware Overview

Top

POE LAN

RJ45 Connector

(Male)

LED

PoE

Port

LAN

Port

Antenna

Connector

LED

Steady White Indicates bootup/initializition/power-on.

Steady Blue Indicates the airGateway is working properly and

an active connection is detected.

Alternating Blue/White Indicates the device is busy; do not

move or unplug.

Bottom

Mounting

Tabs

Reset

Ext

Reset Resets the airGateway to factory defaults. To reset the

airGateway, press and hold the Reset button for more than five

seconds while the airGateway is powered on.

Reset Ext Resets the airMAX

CPE device connected to

the airGateway to factory defaults. To reset the airMAX

device,press and hold the Reset Ext button for more than five

seconds while the airMAX device is powered on.

Installation Requirements

The airGateway is powered by and integrates exclusively with

Ubiquiti Networks PoE adapters. A wall mount kit is included.

• Ubiquiti Networks PoE Adapter (24V, 0.5A)

• Ubiquiti Networks airMAX CPE device

• CAT5/6 cable

• 6 mm drill bit and drill

• Screwdriver

Hardware Installation

WARNING: Do not connect non-PoE devices (such as

laptops) to the POE port.

To install the airGateway, perform the following steps:

1. Disconnect the Ethernet cables from the Ethernet ports

on the PoE Adapter connected to your airMAX CPE device.

Ensure that you note which cable was connected to the

POE port and which cable was connected to the LAN port.

POE

LAN

*720-00066-01*

720-00066-01

2. Insert the male RJ45 Connector of the airGateway into the

Ethernet port labeled POE on the PoEAdapter. Push the

two units together until they connect.

POE

LAN

POE

LAN

3. Connect the Ethernet cable that was disconnected from the

POE port in step 1 to the POE port on the airGateway.

POE

LAN

POE

LAN

4. Connect the Ethernet cable that was disconnected from the

LAN port in step 1 to the LAN port on the airGateway.

POE

LAN

POE

LAN

5. Connect the External Antenna to the Antenna Connector on

the airGateway.

POE

LAN

POE

LAN

Wall Mounting

1. Position the Wall Mount Bracket at the desired location

on the wall with the bubble level at the bottom. Use the

bubble level to ensure the bracket is plumb.

2. Mark the two holes with a pencil.

3. Drill the holes in the wall using a 6 mm drill bit.

4. Insert a Screw Anchor into each hole. Secure the Wall Mount

Bracket to the wall by inserting a Screw into each Screw

Anchor.

5. Attach the airGateway and PoE Adapter assembly to the

Wall Mount Bracket:

a. Insert the two Mounting Tabs on the airGateway into

the slots located at the top of the Wall Mount Bracket.

b. Rotate the PoE Adapter into the Wall Mount Bracket

until it snaps in place.

POE

LAN

POE

LAN

Connecting via Wi-Fi

To configure the airGateway, you must access it via Wi-Fi from

a computer.

1. Connect to the wireless network (SSID) named

www.ubnt.com.

2. Launch your web browser and type https://192.168.1.1 in

the address field. Press enter (PC) or return (Mac).

Note: Your computer needs to be on the

192.168.1.x subnet. If you have DHCP enabled

on your Ethernet adapter, it should receive an

address automatically. If not, you will need to set a

static IP address in the 192.168.1.2 - 192.168.1.254

range.

3. The login screen will appear. Enter ubnt in the Username

and Password fields.

Upon initial login you must select your Country, Language,

and agree to the Terms of Use to use the product. Click

Note: U.S. product versions are locked to the U.S.

Country Code to ensure compliance with FCC

regulations.

4. Change the default airGateway administrator password.

Enter a new password in the New Password and Verify

Password fields and click Next.

5. Enter a name for your wireless network (SSID) and a

password (passphrase) for your wireless network. Click

Next.

6. Verify your settings and click Finish or click Previous to

change the settings.

The airGateway is ready to use. Connect wireless clients as

described below:

Windows

1. Go to Connect to Network.

- Windows 8 Click the Network icon.

- Windows 7 Right-click the Network icon.

- Windows Vista Go to Start > Connect To.

- Windows XP Right-click the Wireless Network icon

in the System Tray (lower right corner of the screen).

Click View Available Wireless Networks.

2. Select the wireless network (SSID) that you defined in the

airGateway Setup Wizard and then click Connect.

Mac

1. Click the AirPort icon in the menu bar (top right side

of the screen).

2. Select the wireless network (SSID) that you defined in the

airGateway Setup Wizard. Once connected, the AirPort

icon will change from gray to solid black.

Specifications

airGateway-LR

Dimensions airGateway: 54 x 44 x 30 mm

Mount: 154 x 49 x 39 mm

Weight 83 g (with mount)

Networking Interface (2) 10/100 Ethernet Ports

Buttons (1) Reset airGateway

(1) Reset External airMAX Device

Enclosure Polycarbonate

Frequency 2.412 - 2.484 GHz

Antenna (1) External 5 dBi

Wi-Fi Standards 802.11 b/g/n (2.4 GHz)

Wireless Security WEP, WPA-PSK, WPA-TKIP,

WPA2 AES, 802.11i

Max. TX Power 18 dBm

Max. Power Consumption 4.0 W

Power Supply 24V, 0.5A PoE Adapter (Not Included)

Power Method Passive Power over Ethernet (24V)

Certications FCC, IC, CE

Mounting Wall Mount Kit (Included)

Operating Temperature -10 to 60° C

Operating Humidity 5 to 95% Non-Condensing

Safety Notices

1. Read, follow, and keep these instructions.

2. Heed all warnings.

3. Only use attachments/accessories specified by the manufacturer.

WARNING: Do not use this product in location that can

be submerged by water.

WARNING: Avoid using this product during an electrical

storm. There may be a remote risk of electric shock from

lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current

requirements indicated on the manufacturer’s label. Connection to a

different power source than those specified may result in improper

operation, damage to the equipment or pose a fire hazard if the

limitations are not followed.

2. There are no operator serviceable parts inside this equipment. Service

should be provided only by a qualified service technician.

Limited Warranty

UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the

product(s) furnished hereunder (the “Product(s)”) shall be free from defects

in material and workmanship for a period of one (1) year from the date

of shipment by UBIQUITI NETWORKS under normal use and operation.

UBIQUITI NETWORKS’ sole and exclusive obligation and liability under

the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion,

to repair or replace any Product that fails to conform to the above

warranty during the above warranty period. The expense of removal and

reinstallation of any Product is not included in this warranty. The warranty

period of any repaired or replaced Product shall not extend beyond its

original term.

Warranty Conditions

The above warranty does not apply if the Product:

(I) has been modified and/or altered, or an addition made thereto,

except by Ubiquiti Networks, or Ubiquiti Networks’ authorized

representatives, or as approved by Ubiquiti Networks in writing;

(II) has been painted, rebranded or physically modified in any way;

(III) has been damaged due to errors or defects in cabling;

(IV) has been subjected to misuse, abuse, negligence, abnormal

physical, electromagnetic or electrical stress, including lightning

strikes, or accident;

(V) has been damaged or impaired as a result of using third party

firmware; or

(VI) has no original Ubiquiti MAC label, or is missing any other original

Ubiquiti label(s).

(VII) has not been received by Ubiquiti within 30 days of issuance of

the RMA.

In addition, the above warranty shall apply only if: the product has been

properly installed and used at all times in accordance, and in all material

respects, with the applicable Product documentation; all Ethernet cabling

runs use CAT5 (or above), and for outdoor installations, shielded Ethernet

cabling is used, and for indoor installations, indoor cabling requirements

are followed.

Returns

No Products will be accepted for replacement or repair without obtaining

a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS

during the warranty period, and the Products being received at UBIQUITI

NETWORKS’ facility freight prepaid in accordance with the RMA process of

UBIQUITI NETWORKS. Products returned without an RMA number will not

be processed and will be returned freight collect or subject to disposal.

Information on the RMA process and obtaining an RMA number can be

found at: www.ubnt.com/support/warranty.

Disclaimer

EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI

NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA,

SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM

AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND,

EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO,

REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY,

ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY,

SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS

FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT AND ANY

WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR

TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES.

BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR

ITS THIRD PARTY PROVIDERS CONTROL BUYER’S EQUIPMENT OR THE

TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING

THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE

SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS

AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS

FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD

PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS,

DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT

CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY

OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant

that the operation of the Products will be error-free or that operation will

be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible

for damages or claims of any nature or description relating to system

performance, including coverage, buyer’s selection of products (including

the Products) for buyer’s application and/or failure of products (including

the Products) to meet government or regulatory requirements.

Limitation of Liability

EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL

UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR

DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES

(INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING

OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE

PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER

LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES.

Note

Some countries, states and provinces do not allow exclusions of implied

warranties or conditions, so the above exclusion may not apply to you.

You may have other rights that vary from country to country, state to

state, or province to province. Some countries, states and provinces do not

allow the exclusion or limitation of liability for incidental or consequential

damages, so the above limitation may not apply to you. EXCEPT TO

THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO

NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE

MANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY

SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations

Convention on Contracts for the International Sale of Goods shall not apply

to any transactions regarding the sale of the Products.

Compliance

FCC

Changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including

interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. Operations of this equipment in a residential area is likely

to cause harmful interference in which case the user will be required to

correct the interference at his own expense.

Industry Canada

This Class A digital apparatus complies with Canadian ICES-003.

To reduce potential radio interference to other users, the antenna

type and its gain should be so chosen that the equivalent isotropically

radiated power (e.i.r.p.) is not more than that permitted for successful

communication.

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference that

may cause undesired operation of the device.

Cet appareil numérique de la classe A est conforme à la norme NMB-003

Canada.

Pour réduire le risque d’interférence aux autres utilisateurs, le type

d’antenne et son gain doivent être choisies de façon que la puissance

isotrope rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessaire

pour une communication réussie.

Cet appareil est conforme à la norme RSS Industrie Canada exempts de

licence norme(s). Son fonctionnement est soumis aux deux conditions

suivantes:

1. Cet appareil ne peut pas provoquer d’interférences et

2. Cet appareil doit accepter toute interférence, y compris les

interférences qui peuvent causer un mauvais fonctionnement du

dispositif.

RF Exposure Warning

The antennas used for this transmitter must be installed to provide a

separation distance of at least 20 cm from all persons and must not be

located or operating in conjunction with any other antenna or transmitter.

Les antennes utilisées pour ce transmetteur doivent être installé en

considérant une distance de séparation de toute personnes d’au moins

20 cm et ne doivent pas être localisé ou utilisé en conflit avec tout autre

antenne ou transmetteur.

Australia and New Zealand

Warning: This is a Class A product. In a domestic environment this

product may cause radio interference in which case the user may

be required to take adequate measures.

CE Marking

CE marking on this product represents the product is in compliance

with all directives that are applicable to it.

RoHS/WEEE Compliance Statement

English

European Directive 2002/96/EC requires that the equipment bearing

this symbol on the product and/or its packaging must not be disposed

of with unsorted municipal waste. The symbol indicates that this

product should be disposed of separately from regular household waste

streams. It is your responsibility to dispose of this and other electric and

electronic equipment via designated collection facilities appointed by the

government or local authorities. Correct disposal and recycling will help

prevent potential negative consequences to the environment and human

health. For more detailed information about the disposal of your old

equipment, please contact your local authorities, waste disposal service, or

the shop where you purchased the product.

Deutsch

Die Europäische Richtlinie 2002/96/EC verlangt, dass technische

Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit diesem

Symbol versehen ist, nicht zusammen mit unsortiertem Gemeindeabfall

entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt

von regulärem Haushaltmüll getrennt entsorgt werden sollte. Es

liegt in Ihrer Verantwortung, dieses Gerät und andere elektrische

und elektronische Geräte über die dafür zuständigen und von der

Regierung oder örtlichen Behörden dazu bestimmten Sammelstellen zu

entsorgen. Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei,

potentielle negative Folgen für Umwelt und die menschliche Gesundheit

zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer

Altgeräte benötigen, wenden Sie sich bitte an die örtlichen Behörden oder

städtischen Entsorgungsdienste oder an den Händler, bei dem Sie das

Produkt erworben haben.

Pagina se încarcă ...

Ubiquiti airGateway-LR Specificație

Marca: Ubiquiti

Model: airGateway-LR

Categorie: Antene de rețea

Tip: Specificație

Acest manual este potrivit și pentru

airGateway

Descărcați PDF

raport

în alte limbi

English: Ubiquiti airGateway-LR Specification
italiano: Ubiquiti airGateway-LR specificazione

Ubiquiti airGateway-LR Specificație

Acest manual este potrivit și pentru

Ubiquiti airGateway-LR Specificație

în alte limbi

Lucrări conexe

Alte documente