DNP DP-QW410 Manual de utilizare

Marca: DNP

Model: DP-QW410

Categorie: Imprimante de etichete

Tip: Manual de utilizare

User Guide

Version 1.0.0

DIGITAL PHOTO PRINTER

DP-QW410

2019120601

WARNING

To reduce the risk of re or electric shock, do not expose this apparatus to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer servicing to qualied personnel only.

This apparatus must be grounded.

For pluggable equipment, the socket-outlet be installed near the equipment and shall be

easily accessible.

To disconnect the main power, unplug the AC IN connector.

This unit has no power switch.

When installing the unit, incorporate a readily accessible disconnect device in the xed wiring,

or connect the power plug to an easily accessible socket-outlet near the unit. If a fault should

occur during operation of the unit, operate the disconnect device to switch the power supply

o, or disconnect the power plug.

Warning on power connection

Use a proper power cord for your local power supply.

1. Use the approved Power Cord (3-core mains lead) /Appliance Connector / Plug with

grounding-contacts that conforms to the safety regulations of each country if applicable.

2. Use the Power Cord (3-core mains lead) / Appliance Connector /Plug conforming to the

proper ratings (Voltage, Ampere).

If you have questions on the use of the above Power Cord/Appliance Connector/Plug, please

consult a qualied service personnel or the distributor.

For the Customers in Europe

This product shall not be used in the residential area.

This is a Class A product. In a domestic environment, this product may cause radio

interference in which case the user may be required to take adequate measures.

Hereby, [Dai Nippon Printing Co., Ltd.] declares that the radio equipment type [DP-QW410] is

in compliance with Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following internet address:

http://www.dnpphoto.eu/en/home

frequency band in which the radio equipment operates;

13.56 MHz±7 kHz

maximum radio-frequency power transmitted in the frequency band in which the radio

equipment operates;

32.69 dBuV/m at 3 m

If you want to dispose this product, do not mix with general household waste.

There is a separate collection system for used electronics products in accordance

with legislation under the WEEE Directive and is eective only within

European Union. For details, consult your dealer.

For kundene i Norge

Dette utstyret kan kobles til et IT-strømfordelingssystem.

italiano

Il fabbricante, [Dai Nippon Printing Co., Ltd.], dichiara che il tipo di apparecchiatura radio [DP-

QW410] è conforme alla direttiva 2014/53/UE.

Il testo completo della dichiarazione di conformità UE è disponibile al seguente indirizzo

Internet: http://www.dnpphoto.eu/en/home

български

С настоящото [Dai Nippon Printing Co., Ltd.] декларира, че този тип радиосъоръжение

[DP-QW410] е в съответствие с Директива 2014/53/ЕС.

Цялостният текст на ЕС декларацията за съответствие може да се намери на следния

интернет адрес: http://www.dnpphoto.eu/en/home

čeština

Tímto [Dai Nippon Printing Co., Ltd.] prohlašuje, že typ rádiového zařízení [DP-QW410] je v

souladu se směrnicí 2014/53/EU.

Úplné znění EU prohlášení o shodě je k dispozici na této internetové adrese:

http://www.dnpphoto.eu/en/home

dansk

Hermed erklærer [Dai Nippon Printing Co., Ltd.], at radioudstyrstypen [DP-QW410] er i

overensstemmelse med direktiv 2014/53/EU.

EU-overensstemmelseserklæringens fulde tekst kan ndes på følgende internetadresse:

http://www.dnpphoto.eu/en/home

magyar

[Dai Nippon Printing Co., Ltd.] igazolja, hogy a [DP-QW410] típusú rádióberendezés megfelel

a 2014/53/EU irányelvnek.

Az EU-megfelelőségi nyilatkozat teljes szövege elérhető a következő internetes címen:

http://www.dnpphoto.eu/en/home

Nederlands

Hierbij verklaar ik, [Dai Nippon Printing Co., Ltd.], dat het type radioapparatuur [DP-QW410]

conform is met Richtlijn 2014/53/EU.

De volledige tekst van de EU-conformiteitsverklaring kan worden geraadpleegd op het

volgende internetadres: http://www.dnpphoto.eu/en/home

polski

[Dai Nippon Printing Co., Ltd.] niniejszym oświadcza, że typ urządzenia radiowego [DP-

QW410] jest zgodny z dyrektywą 2014/53/UE.

Pełny tekst deklaracji zgodności UE jest dostępny pod następującym adresem internetowym:

http://www.dnpphoto.eu/en/home

português

O(a) abaixo assinado(a) [Dai Nippon Printing Co., Ltd.] declara que o presente tipo de

equipamento de rádio [DP-QW410] está em conformidade com a Diretiva 2014/53/UE.

O texto integral da declaração de conformidade está disponível no seguinte endereço de

Internet: http://www.dnpphoto.eu/en/home

Română

Prin prezenta, [Dai Nippon Printing Co., Ltd.] declară că tipul de echipamente radio [DP-

QW410]] este în conformitate cu Directiva 2014/53/UE.

Textul integral al declarației UE de conformitate este disponibil la următoarea adresă internet:

http://www.dnpphoto.eu/en/home

suomi

[Dai Nippon Printing Co., Ltd.] vakuuttaa, että radiolaitetyyppi [DP-QW410] on direktiivin

2014/53/EU mukainen.

EU-vaatimustenmukaisuusvakuutuksen täysimittainen teksti on saatavilla seuraavassa

internetosoitteessa: http://www.dnpphoto.eu/en/home

svenska

Härmed försäkrar [Dai Nippon Printing Co., Ltd.] att denna typ av radioutrustning [DP-QW410]

överensstämmer med direktiv 2014/53/EU.

Den fullständiga texten till EU-försäkran om överensstämmelse nns på följande webbadress:

http://www.dnpphoto.eu/en/home

For the Customer in USA

FCC CAUTION

Changes or modications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct

the interference at his own expense.

Caution: Use shielded cables to connect this computers. Any changes or modications not

expressly approved by the grantee of this device could void the user’s authority to operate the

equipment.

FCC statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

The identication, by name, address and telephone number, of a responsible party located

within the United States.

DNP Imagingcomm America Corporation

4524 Enterprise Drive NW

Concord, NC 28027

United States

Telephone (704) 784-8100

www.dnpimagingcomm.com

For the customers in Canada

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is

subject to the following two conditions: (1) this device may not cause interference, and (2)

this device must accept any interference, including interference that may cause undesired

operation of the device.

For the Customers in Oceania

This instrument is an EMC class A product. In a domestic environment this product may

cause radio interference in which case the user needs to take adequate measures.

Türkçe

AEEE Yönetmeliğine Uygundur

For the customers in Thai

This telecommunication equipment is in compliance with NTC requirements.

Safety precautions

Note that the contents of directions for use and safety precautions correspond to the safety

standards as of the time this manual has been created.

Remodeling

For safety, do not remodel this product after purchase.

Copyrights, trademarks or any other intellectual property rights whatsoever that pertain to

documents, programs or other items provided with this product, are ascribed to Dai Nippon

Printing Co., Ltd., or the respective other holders of rights. Except in cases permitted by

applicable laws, these may not be duplicated or used without consent from Dai Nippon

Printing Co., Ltd.

Table of Contents

Introduction ..................................................................................................... 7

For Safe Operation .......................................................................................... 7

Caution for installation ................................................................................. 10

Printer Installation ........................................................................................ 11

Checking the contents .............................................................................. 11

Name of components ................................................................................12

Connecting the power cord and a computer ............................................. 13

Media (ribbon, paper) ...............................................................................14

Setting the media (ribbon, paper) ............................................................. 15

Paper tray installation ...............................................................................20

Assembling the paper tray ........................................................................ 21

Disposing of paper scrap .......................................................................... 22

Troubleshooting ............................................................................................ 23

Error display ............................................................................................. 23

Solving errors ...........................................................................................24

The printer is jammed with paper ....................................................... 24

The paper cannot be pulled out toward you (paper holder side) ......... 26

The ribbon is caught in the printer ...................................................... 26

Work was continued while the printer unit’s ON/OFF switch is OFF ... 27

The printer stopped with the paper partially cut ..................................27

The power has been cut during printing .............................................27

Cleaning ......................................................................................................... 28

Platen roller .............................................................................................. 28

Thermal print head ................................................................................... 29

Repacking ...................................................................................................... 30

Specications................................................................................................ 31

Thank you for purchasing this product.

This document explains how to handle and operate this product.

Please read this document carefully before use.

Be sure to read “For Safe Operation” (P.7-9), and operate the product correctly.

Be sure to read this document before using the product. After reading, keep it in a safe

place where it can be easily accessed as needed.

The warnings listed here are to ensure proper use of the close up, to prevent physical

injury to the customer or other persons, and to prevent property damage. Please follow

these warnings.

Warnings and Cautions

The possible levels of injury or damage due to misuse are categorized below as Warnings

and Cautions, according to the degree of danger involved.

Warning

Accidents caused by failure to heed the warnings

accompanying this symbol may lead to serious or fatal injury.

Caution

Accidents caused by failure to heed the cautions

accompanying this symbol may lead to physical injury or

property damage.

Symbols

The symbols shown have the following meanings:

This symbol indicates warning and caution messages.

The warning content is indicated in or near the symbol.

This symbol indicates prohibited actions.

The prohibited action is indicated in or near the symbol.

This symbol indicates necessary actions or instructions.

The action is indicated in the symbol.

Introduction

For Safe Operation

Warning

• Use the product only with the designated voltage and frequency. Improper

connection may cause electric shock or re.

• Avoid connecting too many devices to the outlet used for this product and

using extension cords. The outlet may overheat and cause a re.

• Do not damage, cut, bundle, or alter the power cord. Also, the cord may be

damaged if heavy objects are placed on it, or if pulled or bent with excessive

force, and it may cause a re.

• Do not install the product in places with salinity or corrosive gases in the air.

This may cause a re.

• Do not block the vents of the product. Heat may build up in the product and

cause a malfunction or re.

• Do not stand on or place heavy objects on the product. Also, do not apply

excessive force on the buttons, switches, terminals, etc. This may damage

the product and cause injury to the user or other people.

• Store the bag of the product out of the reach of children. It may cause

suocation if placed over the head.

• Be careful not to injure yourself or damage other things on the edges of the

product.

• Do not use this product for applications involving human life (such as

medical, space, aeronautic, or other applications that require extreme

reliability).

• The DP-QW410 weight 5.8 kg (12.76 lbs.). When moving it, lift it in a way that

avoids excessive physical stress. Lifting recklessly or dropping the product

may cause physical injury.

• Place the product as close to an outlet as possible to be able to easily unplug

the power cord in case of problem.

• If there is dust on the plug, clean it o thoroughly. It may cause an electric

shock or a short circuit.

• If metal objects or liquids have fallen into the product, or if there is smoke, a

strange odor, or any other abnormality, immediately unplug the power cord,

and then contact a service representative. Do not continue using the product

if it is damaged or not operating properly. This may cause an electrical shock,

a short circuit, a re, or damage the product.

• For the AC input, use a sine wave input within the range of 100 to 240 V

AC. Using a square wave input or pseudo-sine wave input will damage the

internal circuit and result in signicant shortening of the product life.

• Be sure to ground the product. Otherwise, a short circuit may occur, causing

an electric shock or re.

• Do not plug or unplug the cord with wet hands. This may cause an electric

shock.

• Do not open the product, disassemble internal parts, or modify the product.

It may cause an electric shock, fire, or injury, or a product malfunction.

For internal check-ups, adjustments, or repair, please contact a service

representative.

For Safe Operation

Caution

• Do not install the product in dusty or humid places. This may cause re or an

electric shock, or damage the product.

• Do not install the product on an unstable surface. It may fall and cause injury

to the user or other people.

• Do not allow foreign objects to enter into the product. They may cause an

electric shock, a short circuit, a re, or damage the product. If something falls

into the product, immediately unplug the power cord, and then call a service

representative.

• Do not open the top door or remove the trash box during printing. This may

damage the product.

• Do not spill or spray liquids or chemicals onto the product.

• When cleaning the cover, do not use thinner, trichloroethane, benzene,

ketone-based cleaners, or chemically treated cloths. They could discolor or

deteriorate the cover.

• Take care to not cut, scratch, or hurt your hands the edges of the paper or on

any sharp edges within the printer.

• When putting your hands into the printer for removing the jammed paper or

cleaning, use safety lint-free gloves or other proper protective clothing to

prevent injury.

• At least once a year, unplug the power cord, and clean the prongs and the

plug. If dust accumulates, it may cause a re.

• When printing continuously for long periods in a small room, be sure to

ventilate the room properly.

• If you intend to use the product on a transportation vehicle (train, truck, ship,

etc.), please talk to a representative in advance.

• When disposing of the product, accessories, packaging materials, or media

(paper, ribbon), please abide by local waste removal ordinances. For details,

contact your local government oces.

• When unplugging the cord, always grip the plug. Do not pull on the cord as it

may damage the cord and cause an electric shock or re.

• When moving the product, be sure to unplug the power cord. Otherwise, the

cord may be damaged, which may cause re or an electric shock.

• For safety, when not using the product for an extended period of time, be

sure to unplug the power cord. Otherwise, it may cause an electric shock,

re, or a malfunction.

• Parts with this warning get extremely hot. Do not touch these parts after

printing. There is a danger of burns.

• Do not touch the gear mechanisms. There is a danger of injury if ngers get

caught in spinning gears.

• There is a cutter inside the paper output port. Do not insert hands inside the

paper output port regardless of whether or not the printer is operating.

• Do not look into the paper output port during printing. The edge of the paper

may poke your eye and cause injury.

• Do not touch the paper during printing. The edge of the paper may cause

injury.

For Safe Operation

Caution for installation

• Before using the product, read “For Safe Operation” carefully and observe the

instructions therein.

• Do not use or store the product near a fire, humid places, in direct sunlight, near an

air conditioner or heater, or any other location with unusually high or low temperature,

strong humidity, or excessive dust.

• Do not place the product where chemical reactions occur, such as in a laboratory.

• Do not install the product where there is salinity or corrosive gas in the air.

• The product must be installed on a rm, level surface where there is ample ventilation.

• Do not put anything on top of the product.

• Do not use the product near a radio or television, and do not use the same wall outlet

for the product and a radio or television. Otherwise radio or television reception may be

adversely aected.

• Do not use a power voltage or a frequency other than those specied.

• Do not put anything on the power cord or step on it.

• Do not drag or carry the product by the power cord or the USB cable.

• Avoid plugging the power cord into an outlet with many other cables connected.

• Do not bundle the power cord.

• Always grip the plug housing, not the cord, to plug or unplug the power cord.

• Always unplug the power cord before connecting or disconnecting the USB cable.

• Avoid using a long USB cable or connecting it to any noise-producing device. If it is

unavoidable, use a shielded cable or twisted pair for each signal.

• Use a shielded USB cable compatible with the USB 2.0 specications.

• Place the product near the outlet where the power cord can be unplugged easily to shut

the power o.

• Use an AC outlet that accepts a three-pronged plug. Otherwise, there may be a danger

of electric shock.

• For regions where the power cord is supplied with the product, use this included power

cord set for the product. Do not use the power cord set with other devices.

• When using a portable power source, be sure to read the user guide of the portable

power source, and be sure to ground the portable power source. Otherwise, there may

be a danger of electric shock.

• This product is not intended for use in the immediate/direct visual field of the display

work place. To avoid disturbing reections on the display work place, this product shall

not be placed in the immediate/direct eld of vision.

• Use as a network printer is not anticipated. Any use in conjunction with a network will be

the customer’s sole responsibility.

• This device is not appropriate to be used where a child may be present. Install, store, or

use the device where it cannot be reached by a child.

Printer Installation

Check that the printer and all the following accessories are included in the package.

Caution

• Pay particular attention when removing the product from its package, carrying it, or

moving it. Dropping the printer may result in personal injury or property damage.

• Do not lift the printer by grasping the wrapping materials. The materials may break and

cause the printer to fall.

• Do not put your ngers between the paper holders and spacers. Otherwise, you may get

injured.

Checking the contents

Printer unit Paper tray for (4 x 6") Paper holder

* Set in the printer.

4-inch spacer

* Set in the paper holder.

Explanation booklet

For Safe Operation

Start up guide

Power cord

* Whether a power cord is

included depends

on the country or region.

Paper

output

Trash box

Top door

Opening lever

LEDs

Vent

Fan

USB

5.0 V DC, 2.0 A

Power

inlet

OFF

Front of the unit

Printer Installation

Caution

• Be careful not to hurt yourself or damage anything on the edges of the printer.

Name of components

USB

5.0 V DC, 2.0 A

Power

inlet

OFF

Make sure that the ON/OFF switch of the printer unit is set to OFF.

Make sure that the power switch of the computer is set to OFF.

Plug the connector of the power cord (supplied) into the printer power inlet.

Plug the power cord into an outlet.

Connect the printer unit’s USB connector and the computer with a USB cable.

Set the ON/OFF switch of the printer unit and the power switch of the computer

to ON.

Printer Installation

Caution

• Use a shielded USB cable compatible with the USB 2.0 specications. Otherwise

unexpected troubles may arise.

Connecting the power cord and a computer

Prepare the media (paper, ribbon) with the following widths.

Printer Installation

Caution

• Set the paper and ribbon without putting them directly on the work surface. If dust or dirt

adheres to the media when setting it inside the printer unit, it may adversely aect the print

quality.

Media (ribbon, paper)

When using 4.5-inch paper, remove the spacers attached to the paper holder.

Removing the spacers

1 2 3

Spacer

Size Paper Ribbon

4-inch Width : 102 mm Width : 109 mm

4.5-inch Width : 114 mm Width : 121 mm

Caution

• Do not put your ngers between the paper holders and spacers. Otherwise, you may get

injured.

Printer Installation

Setting the media (ribbon, paper)

Top door

Opening lever

Ribbon

Pull the opening lever toward you to open the printer unit’s top door.

Remove the ribbon.

Caution

• When setting the media, make sure to use the plastic bag or sheet covering the

media. Never put it directly on the table, oor or work spaces.

Caution

• When the top door is opened, take care

that a hand does not get caught in the

gap between the back of the top door and

the printer (see the figure on the right).

Otherwise, you may get injured.

• The thermal head will be hot for some time

after printing. Do not touch the thermal head

as there is a danger of burns.

• When setting or removing the ribbon, be

careful not to let the thermal print head

come into contact with your wristwatch,

accessories, etc. This may damage the

thermal print head.

Take-up side

Supply side

Rotate in the direction of the arrow

to take up the slack.

Set the new ribbon.

Top door

Printer Installation

Install the ribbon to the printer unit.

Align left side (1) of the ribbon shaft with the groove and then lower right side (2) of the

ribbon shaft.

New ribbon

Align with the groove

and then set in place

Trash box

Remove the printer unit’s trash box.

Caution

• When the trash box has been removed, do not touch the cutter on the upper part or

you may be cut.

• In order to facilitate color adjustment, media type recognition, and print quantity

management, an IC chip is included in the ink ribbon. Note that a ribbon with an IC

chip that has not been evaluated and approved may not function properly. (If correct

data cannot be read from the IC chip, an alarm will sound. In such a case, ink

concentration levels will be lowered in order to protect the product.)

Close the printer unit’s top door.

Remove the old paper roll from the paper holder, and then set the new paper roll

ensuring there are no gaps.

If the paper protrudes, remove the roll from the paper holder and set the edge face of

paper at.

Set the roll so that

there are no gaps.

Set the paper so that

it does not protrude

from the roll.

Caution

• When setting the media, make sure to use the plastic bag or sheet covering the

media. Never put it directly on the table, oor or work spaces.

Printer Installation

Paper holder

Remove the paper holder from the printer.

Caution

• When removing the paper holders to change the paper roll etc., make sure to place

them on the clean surface. Never place them directly on the table or work spaces.

If dust or dirt adheres to the media when setting the paper holder inside the printer

unit, it may adversely aect the print quality.

Printer Installation

Caution

• The paper holders with a new paper roll set on it weigh approximately 1 kg. Do not

let them fall as they may cause physical injury or damage to the paper holders.

Set the paper holder into the printer.

Set the seal on the paper (→PULL) in the

same direction as shown on the right.

Remove the seal, place a hand on the

paper, and rotate the paper holder in the

direction of the arrow to insert the paper

leading edge until the buzzer beeps.

The ERROR LED changes from flashing red

and orange alternately to ashing red.

LEDs

Caution

• If the paper is slack, such as when the paper

holder is rotated without supporting the paper

with your hand, paper initialization may fail.

Printer Installation

Caution

• Make sure that the trash box is installed when printing. If not installed, your ngers

may get caught in the moving parts and be injured.

• If different width media, for example 4-inch and 4.5-inch, are used on the same

printer, problems with the print quality such as lines on the print could arise.

Therefore, do not mix the use of dierent width media on one printer.

• Make sure to perform paper initialization during paper replacement. If paper

initialization is not performed, problems with the print quality could arise.

• Do not touch the paper during printing. The edge of the paper may cause injury, and

problems with the print quality could arise.

Caution

• If the trash box is not closed, the ERROR LED ashes red.

Make sure to close the trash box, ensuring that there is no gap between it and the

printer unit.

A gap between the trash box and the printer unit can result in malfunctions.

It can also result in foreign objects or dust getting into the printer unit, adversely

aecting print quality.

Trash

box

LEDs

Printing is not possible with the trash box removed.

Attach the printer unit’s trash box.

Perform paper initialization. (Three blank sheets are output.)

Paper initialization cuts o the outer edges of the paper that may be dirty.

However, paper initialization will not be carried out if the printer unit's ON/OFF switch

is set to ON after the paper is replaced.

Insert the tray horizontally.

Printer Installation

You can use the paper tray when printing.

Up to 20 sheets can be stored, however it is recommended to remove the sheets regularly.

Insert the paper tray into the attachment

parts on the sides of the printer unit’s

paper output port.

Lower the paper tray to set it.

Paper tray installation

Caution

• Storing too many sheets in the paper tray may cause a malfunction.

• Do not apply too much strength on the paper tray. Otherwise, it may be damaged.

• The paper tray is specically for 4 x 6" paper. It cannot store paper of any other print

sizes.

• Make sure that printed paper does not get caught in the paper output port. This may

cause a paper jam.

Pagina se încarcă ...

DNP DP-QW410 Manual de utilizare

Marca: DNP

Model: DP-QW410

Categorie: Imprimante de etichete

Tip: Manual de utilizare

Descărcați PDF

raport

în alte limbi

English: DNP DP-QW410 User manual

DNP DP-QW410 Manual de utilizare

DNP DP-QW410 Manual de utilizare

în alte limbi

Alte documente