Enterprise VoIP Phone with
7" Touchscreen, Bluetooth,
WiFi, and Built-In Camera
Model: UVP-Executive
Introduction
Thank you for purchasing the UniFi
®
VoIP Phone Executive,
model UVP-Executive. Designed to integrate easily into a
UniFi network, the interface is based on the popular Android
™
platform for ease of use. This Quick Start Guide is designed
to guide you through the installation, provide an overview of
the interface, important 911 emergency call information, and
includes the warrantyterms.
Package Contents
Enterprise VoIP Phone with
7" Touchscreen, Bluetooth,
WiFi, and Built-In Camera
Model: UVP-Executive
UniFi VoIP Phone
Executive
Micro Cloth Quick Start Guide
Installation Requirements
• UniFi Switch or PoE+ (802.3at-compliant) switch
• UniFi Controller
• Third-Party SIP/PBX Provider
TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above). It is the customer’s
responsibility to follow local country regulations and indoor cabling requirements.
Before You Begin
Remove the protective
covering from the handset.
Remove the protective film
from the touchscreen.
Hardware Overview
Front
Volume
Camera
LED
Touchscreen
Camera Built-in camera can be used for snapping photos for
avatars or videoconferencing applications.
Touchscreen The 7" (diagonal) touchscreen display is used for
all interface navigation and dialing.
Volume Use the volume arrows to adjust audio levels.
LED The LED will illuminate when the device is first connected
to a 48V power source. Once the phone has started up, the
LED will turn off.
IMPORTANT: The LED will flash when a firmware update
is occurring. Do not disconnect power/Ethernet from the
device during this time.
Back Ports
PC
PoE/LAN
PoE/LAN
PC
USB
USB The USB port can connect to an external speaker or a
mass storage device.
PoE/LAN The PoE/LAN Ethernet port is 802.3at-compliant
and is used to connect data and power to the phone. Connect
this port to the same network as the UniFi Security Gateway
VOIP port.
PC The Ethernet port labeled PC is used for bridging.
WARNING: Do not connect a powered Ethernet
connection to the port labeled PC.
Side Ports
Micro-USB Port The Micro-USB port is only
intended for advanced users connecting the phone
to a computer.
Headset Jack 3.5 mm jack for optional wired stereo
and microphone headsets.
Handset
Mute button
Mute Press the Mute button to mute the microphone on the
handset.
*640-00144-10*
640-00144-10
Hardware Installation
The UniFi VoIP Phone Executive is designed for desktop
placement. To connect the phone, perform the following steps:
1. Connect one end of an Ethernet cable to the wall jack that
is connected to your 48V, 802.3at-compliant switch.
2. Connect the other end of the Ethernet cable to the port
labeled PoE/LAN on the UniFi VoIP Phone Executive.
PC
PoE/LAN
Software Configuration
The UniFi VoIP Phone Executive is automatically detected by
the UniFi Controller (4.6.x or above).
Installing the UniFi Controller
If you haven’t already installed the UniFi Controller software,
you can download it at downloads.ubnt.com/unifi
Adopting the Phone in the UniFi Controller
1. Launch the UniFi Controller and go to the Devices tab.
2. Click Adopt.
Navigating the Interface
Google
™
Search Widget
Use the Google search widget to type or speak
voice commands. Touch the g logo to bring up
a virtual keyboard, or touch the microphone
icon to say a voice command.
Default Home Screen Icons
Icon Description
Settings Display and configure the network,
device, accounts, and system settings.
People Press to view a list of contacts.
Google Play
™
Store Press to open the Google
Play store. Download apps, music, movies,
books, games, and other media. A new or
existing account is required for access.
Phone Displays the keypad to make a call.
Recent calls, contacts, and voicemail are also
accessible from here.
Camera Press to access the camera.
Apps Press to access the Apps screen. This
default icon is the only one that cannot be
removed from the Home screen.
Google Apps Folder Contains the Google
suite of apps including Gmail
™
, YouTube
™
,
Chrome
™
, Hangouts
™
, Google Drive
™
,
GoogleMaps
™
, and more.
Action Bar Icons
Icon Description
Back Opens the previous screen you were
working in, even if it was in a different app.
Once you return to the Home screen, you can’t
go back any further.
Home Returns to the Home screen.
Recent Apps Displays a list of recently used
apps. Press an app to open it. To close an app
and remove it from the list, swipe it left or right.
Customizing the Home Screen
Widgets and shortcuts to favorite apps can be placed on the
Home screen. Multiple app shortcuts can also be grouped into
one folder.
Adding App Shortcuts to the Home Screen
To place an app on the Home screen, press the Apps icon on
the Home screen. The Apps screen will be displayed. Press and
hold the icon until it appears on the Home screen. Drag the
icon to the desired location and release it.
Creating Folders on the Home Screen
To create a folder containing multiple app shortcuts, drag an
app shortcut over another app shortcut on the Home screen.
Removing Items from the Home Screen
To remove a widget or app shortcut from the Home screen,
press and hold the item until the Remove text appears at the
top of the screen. Drag the item to the Remove text.
Apps Screen
Pressing the Apps icon brings up the Apps screen. Touch an
app icon to launch an app.
Making a Call
Lift the handset to make a call and the dialer screen will
appear. Use the touchscreen to enter the phone number. Use
the Delete button to correct any mistakes. Press the Call button
to make a call.
Delete
Contacts
Call
Call Manager
CALL OPTIONS
Volume
Slider
Connected
Number
Connection
Status
Connected Number Displays the extension or phone number
that is being dialed or that is currently connected.
Volume Slider Use the slider to increase or decrease the
volume level.
Connection Status Displays “Dialing” or the total elapsed
time of the currently connected call.
For more details on using the UniFi VoIP Phone Executive, refer
to the user guide at documentation.ubnt.com
Specifications
UVP-Executive
Dimensions 254.6 x 135 x 182.5 mm (10.02 x 5.31 x 7.19")
Weight 1.52 kg (3.35 lbs)
Display
7" (Diagonal), 1024 x 600, 170 ppi,
Multi-Touch, Full Color
Camera 1.0 MP (HD720p)
LED Power: White, Glowing
Handset
Dynamic Receiver 32 ohm/101 dB/30mW
Microphone Omnidirectional/-36dB/2.2Kohm
Echo Cancellation DSP Removing Ambient Noise
and Acoustic Echo
Power Input PoE+ 802.3.at (26W)
Hands-Free Speaker Stereo 4.0W
Hands-Free
Microphone
Omnidirectional/SNR 61 ± 5 dB/
Sensitivity -38 ± 3dB Analog Silicon Microphone
Connectivity (2) 10/100/1000 Ethernet Ports
(1) USB 2.0 Micro-USB Port
(1) USB 2.0 Type A USB Host Port
Bluetooth 4.0
Wi-Fi 802.11 a/b/g/n
Headset Support 3.5 mm Audio Jack
270mW CTIA (LRGM)
Accessory Detection Volume Up/Down and Media Detection
Processor Dual-Core Cortex A9, 1.2 GHz
Storage 4 GB (Shared with Other Applications)
RAM 1 GB
Software
OS Android 4.4, KitKat®
Voice Codec G.722/Speex/iLBC/PCMU/PCMA/GSM
Communication
Software
UniFi Phone App
Protocol SIP/SDP/RTP/RTCP/VLAN/DHCP
Important Warning Regarding Emergency Calls
NOTE THAT THE LIMITATIONS SET FORTH BELOW ARE APPLICABLE TO
ALL EMERGENCY CALLS, FUNCTIONS AND SERVICES, INCLUDING 911,
ENHANCED 911 AND 112 CALLS (COLLECTIVELY, “EMERGENCY SERVICES”).
1. You should be aware that:
a. Emergency Services may not connect to the Public Service
Answering Point (“PSAP”), or may ring to the administrative line
of the PSAP, which may not be staffed after hours, or by trained
emergency operators.
b. VoIP customers may need to provide location or other information
to their VoIP providers, and update this information if they change
locations, for their Emergency Services to function properly.
c. VoIP service may not work during a power outage, or when
the Internet connection fails or becomes overloaded. Consider
installing a backup power supply, maintaining a traditional phone
line or having a wireless phone as a backup.
d. VoIP service will not function if the telephone equipment or other
equipment necessary to place calls is not correctly configured.
e. Emergency Services may correctly connect to the PSAP, but may
not transmit the user’s phone number and/or location information.
f. VoIP calls may not be capable of being received and/or processed
by an emergency call center due to the center’s technical
limitations.
g. VoIP calls may be affected by other factors or force majeure events,
such as the quality of the broadband connection and network
congestion.
2. You should:
a. Provide your accurate physical address to your interconnected
VoIP service provider to ensure that emergency services can
quickly be dispatched to your location.
b. Be familiar with your VoIP service provider’s procedures for
updating your address, and promptly update address information
in the event of a change.
c. Have a clear understanding of any limitations of your Emergency
Services.
d. Inform children, babysitters and visitors about your VoIP service
and its Emergency Services limitations.
3. By installing the phone, you are affirmatively acknowledging that (i) you
have read and understood this Warning, (ii) you understand that you
may not be able to contact emergency services by dialing or using any
Emergency Service, and (iii) you understand that you must inform users
of the phone that they may not be able to contact emergency services
by dialing or using any Emergency Service.
4. IN NO EVENT SHALL UBIQUITI NETWORKS, ITS AFFILIATES,
OFFICERS, DIRECTORS, EMPLOYEES, REPRESENTATIVES, AGENTS
OR ANY OTHER THIRD-PARTY PROVIDER OR VENDOR WHO MAY
FURNISH SERVICES OR PRODUCTS TO YOU IN CONNECTION WITH
THE VOIP SERVICES OR THE EQUIPMENT BE HELD LIABLE FOR
ANY CLAIM, DAMAGE, OR LOSS WHATSOEVER ARISING FROM OR
RELATING TO EMERGENCY SERVICES, AND YOU HEREBY WAIVE ANY
AND ALL SUCH CLAIMS OR CAUSES OF ACTION ARISING THEREFROM
OR RELATING THERETO.
Safety Notices
1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories specified by the manufacturer.
WARNING: Do not use this product in location that can
be submerged by water.
Electrical Safety Information
1. Compliance is required with respect to voltage, frequency, and current
requirements indicated on the manufacturer’s label. Connection to a
different power source than those specified may result in improper
operation, damage to the equipment or pose a fire hazard if the
limitations are not followed.
2. There are no operator serviceable parts inside this equipment. Service
should be provided only by a qualified service technician.
3. This equipment is provided with a detachable power cord which has
an integral safety ground wire intended for connection to a grounded
safety outlet.
a. The equipment requires the use of the ground wire as a part of the
safety certification, modification or misuse can provide a shock
hazard that can result in serious injury or death.
b. Contact a qualified electrician or the manufacturer if there
are questions about the installation prior to connecting the
equipment.
c. Protective earthing is provided by Listed AC adapter. Building
installation shall provide appropriate short-circuit backup
protection.
d. Protective bonding must be installed in accordance with local
national wiring rules and regulations.
Limited Warranty
UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the
product(s) furnished hereunder (the “Product(s)”) shall be free from defects
in material and workmanship for a period of one (1) year from the date
of shipment by UBIQUITI NETWORKS under normal use and operation.
UBIQUITI NETWORKS’ sole and exclusive obligation and liability under
the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion,
to repair or replace any Product that fails to conform to the above
warranty during the above warranty period. The expense of removal and
reinstallation of any Product is not included in this warranty. The warranty
period of any repaired or replaced Product shall not extend beyond its
original term.
Warranty Conditions
The above warranty does not apply if the Product:
(I) has been modified and/or altered, or an addition made thereto,
except by Ubiquiti Networks, or Ubiquiti Networks’ authorized
representatives, or as approved by Ubiquiti Networks in writing;
(II) has been painted, rebranded or physically modified in any way;
(III) has been damaged due to errors or defects in cabling;
(IV) has been subjected to misuse, abuse, negligence, abnormal physical,
electromagnetic or electrical stress, including lightning strikes, or
accident;
(V) has been damaged or impaired as a result of using third party
firmware;
(VI) has no original Ubiquiti MAC label, or is missing any other original
Ubiquiti label(s); or
(VII) has not been received by Ubiquiti within 30 days of issuance of
the RMA.
In addition, the above warranty shall apply only if: the product has been
properly installed and used at all times in accordance, and in all material
respects, with the applicable Product documentation; all Ethernet cabling
runs use CAT5 (or above), and for outdoor installations, shielded Ethernet
cabling is used, and for indoor installations, indoor cabling requirements
are followed.
Returns
No Products will be accepted for replacement or repair without obtaining
a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS
during the warranty period, and the Products being received at UBIQUITI
NETWORKS’ facility freight prepaid in accordance with the RMA process of
UBIQUITI NETWORKS. Products returned without an RMA number will not
be processed and will be returned freight collect or subject to disposal.
Information on the RMA process and obtaining an RMA number can be
found at: www.ubnt.com/support/warranty.
Disclaimer
EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI
NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA,
SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM
AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND,
EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO,
REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY,
ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY,
SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS
FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT AND ANY
WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR
TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES.
BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR
ITS THIRD PARTY PROVIDERS CONTROL BUYER’S EQUIPMENT OR THE
TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING
THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE
SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS
AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS
FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD
PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS,
DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT
CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY
OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant
that the operation of the Products will be error-free or that operation will
be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible
for damages or claims of any nature or description relating to system
performance, including coverage, buyer’s selection of products (including
the Products) for buyer’s application and/or failure of products (including
the Products) to meet government or regulatory requirements.
Limitation of Liability
EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL
UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR
DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES
(INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING
OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE
PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER
LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES.
Note
Some countries, states and provinces do not allow exclusions of implied
warranties or conditions, so the above exclusion may not apply to you.
You may have other rights that vary from country to country, state to
state, or province to province. Some countries, states and provinces do not
allow the exclusion or limitation of liability for incidental or consequential
damages, so the above limitation may not apply to you. EXCEPT TO
THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO
NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE
MANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY
SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations
Convention on Contracts for the International Sale of Goods shall not apply
to any transactions regarding the sale of the Products.
Compliance
FCC
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions.
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Operations of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the
interference at his own expense.
This radio transmitter FCC ID: SWX-UVPEXT has been approved by FCC
to operate with the antenna types listed below with the maximum
permissible gain and required antenna impedance for each antenna type
indicated. Antenna types not included in this list, having a gain greater
than the maximum gain indicated for that type, are strictly prohibited for
use with this device.
Antenna Information
Antenna type: Chip Antenna
Antenna gain: 5.18 dBi
Industry Canada
CAN ICES-3(B)/NMB-3(B)
To reduce potential radio interference to other users, the antenna
type and its gain should be so chosen that the equivalent isotropically
radiated power (e.i.r.p.) is not more than that permitted for successful
communication.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that
may cause undesired operation of the device.
This radio transmitter (IC: 6545A-UVPEXT) has been approved by Industry
Canada to operate with the antenna types listed below with the maximum
permissible gain and required antenna impedance for each antenna type
indicated. Antenna types not included in this list, having a gain greater
than the maximum gain indicated for that type, are strictly prohibited for
use with this device.
Antenna Information
Antenna Information: Chip Antenna
Antenna gain: 5.18 dBi
CAN ICES-3(B)/NMB-3(B)
Pour réduire le risque d’interférence aux autres utilisateurs, le type
d’antenne et son gain doivent être choisies de façon que la puissance
isotrope rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessaire
pour une communication réussie.
Cet appareil est conforme à la norme RSS Industrie Canada exempts de
licence norme(s). Son fonctionnement est soumis aux deux conditions
suivantes:
1. Cet appareil ne peut pas provoquer d’interférences et
2. Cet appareil doit accepter toute interférence, y compris les interférences
qui peuvent causer un mauvais fonctionnement du dispositif.
Cet émetteur radio (IC: 6545A-UVPEXT) a été approuvée par Industrie
Canada pour l'exploitation avec l'antenne types énumérés ci-dessous
avec le gain maximal admissible et requis l'impédance de l'antenne pour
chaque type de l'antenne indiqué. Types d'antenne non inclus dans cette
liste, ayant un gain supérieur au gain maximal indiqué pour ce type, sont
strictement interdits pour une utilisation avec cet appareil.
Informations Antenne
Informations antenne: Chip Antenna
Gain de l'antenne: 5.18 dBi
RF Exposure Warning
The antennas used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be
located or operating in conjunction with any other antenna or transmitter.
Les antennes utilisées pour ce transmetteur doivent être installé en
considérant une distance de séparation de toute personnes d'au moins
20 cm et ne doivent pas être localisé ou utilisé en conflit avec tout autre
antenne ou transmetteur.
CE Marking
CE marking on this product represents the product is in compliance with all
directives that are applicable to it.
Alert Sign (!) Follows CE Marking
Alert sign must be indicated if a restriction on use applied to the product
and it must follow the CE marking.
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
Ubiquiti UVP-EXECUTIVE Ghid de inițiere rapidă
- Tip
- Ghid de inițiere rapidă
- Acest manual este potrivit și pentru
în alte limbi
- English: Ubiquiti UVP-EXECUTIVE Quick start guide
- italiano: Ubiquiti UVP-EXECUTIVE Guida Rapida
Lucrări conexe
-
Ubiquiti UniFi UVP Ghid de inițiere rapidă
-
-
-
Ubiquiti Networks XR5 Manual de utilizare
-
Ubiquiti UAP-PRO Ghid de inițiere rapidă
-
-
-
-
Ubiquiti UniFi Ghid de inițiere rapidă
-