Brooks 0251 / 0254 Instrucțiuni de utilizare

Installation and Operation Manual

X-SE-0250-Series-eng

Part Number: 541B129AAG

October, 2017

0250 Series

5

Gas and Liquid Mass Flow

Secondary Electronics

Model 0254

Table Top Four Channel

Secondary Electronics

Model 0251

Single Channel

Secondary Electronics

Installation and Operation Manual

X-SE-0250-Series-eng

Part Number: 541B129AAG

October, 2017

0250 Series

ESD (Electrostatic Discharge)

CAUTION: This instrument contains electronic components that are susceptible to damage by static electricity. Proper handling procedures must be observed

during the removal, installation or other handling of internal circuit boards or devices.

Handling Procedure:

1. Power to unit must be removed.

2. Personnel must be grounded, via a wrist strap or other safe, suitable means before any printed circuit card or other internal device is installed,

removed or adjusted.

3. Printed circuit cards must be transported in a conductive container. Boards must not be removed from protective enclosure until immediately before

installation. Removed boards must immediately be placed in protective container for transport, storage or return to factory.

Comments

This instrument is not unique in its content of ESD (electrostatic discharge) sensitive components. Most modern electronic designs contain components

that utilize metal oxide technology (NMOS, SMOS, etc.). Experience has proven that even small amounts of static electricity can damage or destroy these

devices. Damaged components, even though they appear to function properly, exhibit early failure.

Brooks Instrument designs, manufactures and tests its products to meet many national and international standards. These products must be properly

installed, operated and maintained to ensure they continue to operate within their normal specifications. The following instructions must be adhered to

and integrated into your safety program when installing, operating and maintaining Brooks Instrument products.

• To ensure proper performance, use qualified personnel to install, operate, update, program and maintain the product.

• Read all instructions prior to installing, operating and servicing the product. If this instruction manual is not the correct manual, please see back cover

for local sales office contact information. Save this instruction manual for future reference.

WARNING: Do not operate this instrument in excess of the specifications listed in the Instruction and Operation Manual. Failure to heed

this warning can result in serious personal injury and / or damage to the equipment.

• If you do not understand any of the instructions, contact your Brooks Instrument representative for clarification.

• Follow all warnings, cautions and instructions marked on and supplied with the product.

WARNING: Prior to installation ensure this instrument has the required approval ratings to meet local and national codes. Failure to heed this warning can

result in serious personal injury and / or damage to the equipment.

• Install your equipment as specified in the installation instructions of the appropriate instruction manual and per applicable local and national codes.

Connect all products to the proper electrical and pressure sources.

• Operation: (1) Slowly initiate flow into the system. Open process valves slowly to avoid flow surges. (2) Check for leaks around the flow meter inlet

and outlet connections. If no leaks are present, bring the system up to the operating pressure.

• Please make sure that the process line pressure is removed prior to service. When replacement parts are required, ensure that qualified people use

replacement parts specified by Brooks Instrument. Unauthorized parts and procedures can affect the product's performance and place the safe

operation of your process at risk. Look-alike substitutions may result in fire, electrical hazards or improper operation.

• Ensure that all equipment doors are closed and protective covers are in place to prevent electrical shock and personal injury, except when

maintenance is being performed by qualified persons.

WARNING: For liquid flow devices, if the inlet and outlet valves adjacent to the devices are to be closed for any reason, the devices must be completely

drained. Failure to do so may result in thermal expansion of the liquid that can rupture the device and may cause personal injury.

All pressure equipment with an internal pressure greater than 0.5 bar (g) and a size larger than 25mm or 1" (inch) falls under the Pressure Equipment Directive (PED).

• The Specifications Section of this manual contains instructions related to the PED directive.

• Products described in this manual are in compliance with EN directive 2014/34/EU.

• All Brooks Instrument Flowmeters fall under fluid group 1.

• Products larger than 25mm or 1" (inch) are in compliance with PED category I, II or III.

• Products of 25mm or 1" (inch) or smaller are Sound Engineering Practice (SEP).

The Brooks Instrument (electric/electronic) equipment bearing the CE mark has been successfully tested to the regulations of the Electro Magnetic

Compatibility (EMC directive 2014/30/EU).

Special attention however is required when selecting the signal cable to be used with CE marked equipment.

Quality of the signal cable, cable glands and connectors:

Brooks Instrument supplies high quality cable(s) which meets the specifications for CE certification.

If you provide your own signal cable you should use a cable which is overall completely screened with a 100% shield.

“D” or “Circular” type connectors used should be shielded with a metal shield. If applicable, metal cable glands must be used providing cable screen clamping.

The cable screen should be connected to the metal shell or gland and shielded at both ends over 360 Degrees.

The shield should be terminated to an earth ground.

Card Edge Connectors are standard non-metallic. The cables used must be screened with 100% shield to comply with CE certification.

The shield should be terminated to an earth ground.

For pin configuration : Please refer to the enclosed Instruction Manual.

European Pressure Equipment Directive (PED)

European Electromagnetic Compatibility (EMC)

Essential Instructions

Read before proceeding!

Installation and Operation Manual

X-SE-0250-Series-eng

Part Number: 541B129AAG

October, 2017

0250 Series

Dear Customer,

We appreciate this opportunity to service your flow measurement and control requirements with a Brooks

Instrument device. Every day, flow customers all over the world turn to Brooks Instrument for solutions to their

gas and liquid low-flow applications. Brooks provides an array of flow measurement and control products for

various industries from biopharmaceuticals, oil and gas, fuel cell research and chemicals, to medical devices,

analytical instrumentation, semiconductor manufacturing, and more.

The Brooks product you have just received is of the highest quality available, offering superior performance,

reliability and value to the user. It is designed with the ever changing process conditions, accuracy requirements

and hostile process environments in mind to provide you with a lifetime of dependable service.

We recommend that you read this manual in its entirety. Should you require any additional information concerning

Brooks products and services, please contact your local Brooks Sales and Service Office listed on the back cover

of this manual or visit www.BrooksInstrument.com

Yours sincerely,

Brooks Instrument

Installation and Operation Manual

X-SE-0250-Series-eng

Part Number: 541B129AAG

October, 2017

0250 Series

THIS PAGE WAS

INTENTIONALLY

LEFT BLANK

i

Contents

Installation and Operation Manual

X-SE-0250-Series-eng

Part Number: 541B129AAG

October, 2017

0250 Series

Paragraph Page

Number Number

Section 1 Introduction

1-1 Description .................................................................................................................................1-1

1-1-1 Architecture................................................................................................................................1-1

1-1-2 Communication .......................................................................................................................... 1-1

1-1-3 Process Controls .......................................................................................................................1-1

1-1-4 Operator Controls and Indicators...............................................................................................1-2

1-1-5 Diagnostic Capabilities...............................................................................................................1-2

1-2 Specifications (Reference Table 1-1) ......................................................................................... 1-2

1-3 Signal Wiring (Reference Figures 1-1 and 1-2) .........................................................................1-4

1-4 Optional Equipment ...................................................................................................................1-4

1-4-1 Mounting Kit Options..................................................................................................................1-4

1-4-2 Power Supply Options................................................................................................................1-4

1-4-3 Input/Output Pin-Out Adapters ...................................................................................................1-4

Section 2 Installation

2-1 General ...................................................................................................................................... 2-1

2-2 Receipt of Equipment.................................................................................................................2-1

2-3 Recommended Storage Practice ............................................................................................... 2-1

2-4 Return Shipment ........................................................................................................................ 2-2

2-5 Transit Precautions .................................................................................................................... 2-2

2-6 Removal from Storage ...............................................................................................................2-2

2-7 Ventilation and Mounting Requirements .................................................................................... 2-2

2-8 Cleaning Instructions ................................................................................................................. 2-2

2-9 Cable Requirements .................................................................................................................. 2-3

2-10 Installation Instructions .............................................................................................................. 2-3

2-10-1 Panel Mount Installation Instructions .........................................................................................2-3

2-10-2 Table Top Stand Assembly Instructions......................................................................................2-5

2-10-3 Retrofit to Model 0152/0154 Table Top Housing (Model 0254 only)...........................................2-7

2-10-4 19-in. Rack Assembly and Installation Instructions (Model 0254 only) ...................................... 2-8

Section 3 Operation

3-1 Home Screen............................................................................................................................. 3-1

3-2 Operating Controls..........................................................................................................

........... 3-2

3-2-1 Primary Functions ......................................................................................................................3-2

3-2-2 Key Functions ............................................................................................................................3-3

3-3 Navigation ..................................................................................................................................3-4

3-3-1 Display or Instrument Configuration Screen Selection...............................................................3-4

3-3-2 User Interface Screen Map........................................................................................................3-5

3-4 Process Values (PV) and Setpoints (SP) ...................................................................................3-7

3-4-1 PV-SP Measures and Status......................................................................................................3-7

3-4-2 PV-SP Configuration ..................................................................................................................3-8

3-4-3 Value Programming ...................................................................................................................3-9

3-5 Global Settings.......................................................................................................................... 3-12

3-5-1 Global Information.....................................................................................................................3-12

3-5-2 Global System Power................................................................................................................3-13

3-5-3 Global Control Services ............................................................................................................ 3-14

3-5-4 Global Communication.............................................................................................................. 3-15

3-6 Instrument Configuration and Control ....................................................................................... 3-15

3-6-1 Rate (Setpoint) Control .............................................................................................................3-15

0250 Series

ii

Contents

Installation and Operation Manual

X-SE-0250-Series-eng

Part Number: 541B129AAG

October, 2017

Paragraph Page

Number Number

3-6-2 PV Configuration....................................................................................................................... 3-17

3-6-3 Batch Control ............................................................................................................................3-18

3-6-4 Blend Control (Model 0254 only)............................................................................................... 3-19

3-6-4-1 Blend Control Setup .................................................................................................................. 3-20

3-6-4-2 Start Blend ................................................................................................................................ 3-21

3-6-4-3 Terminate Blend In-Process...................................................................................................... 3-22

3-6-5 SP VOR (Valve Override) Function ...........................................................................................3-22

3-6-6 Totalization ................................................................................................................................ 3-23

3-6-7 Emergency Off.......................................................................................................................... 3-24

Appendix A Engineering Units

Available Engineering Units .......................................................................................................A-1

Appendix B Blending Examples

Examples 1 through 6 ................................................................................................................B-1

Appendix C Serial Communications Protocol

C-1 Overview ....................................................................................................................................C-1

C-2 Communication Settings ............................................................................................................C-1

C-2-1 RS232 Port Settings ..................................................................................................................C-1

C-2-2 Hyperterminal Set-Up ................................................................................................................C-2

C-3 Serial Command Organization...................................................................................................C-3

C-3-1 Command Structures .................................................................................................................C-3

C-3-2 Command Addressing................................................................................................................C-6

C-4 Command Operation..................................................................................................................C-7

C-4-1 General Commands...................................................................................................................C-7

C-4-1-1 Command Syncronize................................................................................................................C-7

C-4-1-2 Menu Command ........................................................................................................................C-7

C-4-1-3 View Programmed Channel Port Values ....................................................................................C-8

C-4-1-4 Identify Command......................................................................................................................C-8

C-4-1-5 Message Serial Character Pacing Controls ...............................................................................C-9

C-4-1-6 Serial Message Error Control....................................................................................................C-10

C-4-2 Channel Input Port Commands.................................................................................................C-11

C-4-2-1 Measure Channel Values Command ........................................................................................C-

11

C-4-2-2 Send Channel Input Port Programmed Values .........................................................................C-12

C-4-2-3 Program Channel Input Port Values..........................................................................................C-13

C-4-2-4 Clear Accumulated Values ........................................................................................................C-13

C-4-3 Channel Output Port Control Commands .................................................................................C-13

C-4-3-1 Channel Control Output Port Values .........................................................................................C-13

C-4-3-2 Batch and Blend Control Commands........................................................................................C-14

C-4-4 Global Settings Services...........................................................................................................C-16

C-4-4-1 Global Setting Values................................................................................................................C-16

C-4-4-2 Set Global Settings Values........................................................................................................C-16

C-4-5 Communication Message Basics..............................................................................................C-16

C-4-5-1 Message Structure ....................................................................................................................C-17

C-4-5-2 Message Format.......................................................................................................................C-17

iii

Contents

Installation and Operation Manual

X-SE-0250-Series-eng

Part Number: 541B129AAG

October, 2017

0250 Series

Paragraph Page

Number Number

C-5 Serial Value Programming ........................................................................................................C-18

C-5-1 Read a Programmed Value.......................................................................................................C-18

C-5-2 Program a New Value ...............................................................................................................C-19

C-5-3 Channel Input Port Values ........................................................................................................C-20

C-5-4 Channel Output Port Values......................................................................................................C-22

C-5-5 Global Setting Values................................................................................................................C-23

Appendix D CE Essential Instructions

Essential Instructions .................................................................................................................D-1

Warranty, Local Sales/Service Contact Information....................................................................... Back Cover

Figures

Figure Page

Number Number

1-1 Model 0251 Signal Wiring ..........................................................................................................1-5

1-2 Model 0254 Signal Wiring ..........................................................................................................1-5

2-1 Panel Mount Cut-Out Dimensions ............................................................................................. 2-4

2-2 Table Top Stand Mount Installation ............................................................................................ 2-6

2-3 Power Supply Bracket and Bezel...............................................................................................2-9

2-4 Rack Installation.........................................................................................................................2-9

3-1 Home Screen............................................................................................................................. 3-1

3-2 Model 0251 - User Interface Screen Map ..................................................................................3-5

3-3 Model 0254 - User Interface Screen Map ..................................................................................3-6

Tables

Table Page

Number Number

1-1 Specifications - 0250 Series.......................................................................................................1-3

3-1 Display Home Screen Fields...................................................................................................... 3-1

0250 Series

iv

Contents

Installation and Operation Manual

X-SE-0250-Series-eng

Part Number: 541B129AAG

October, 2017

THIS PAGE WAS

INTENTIONALLY

LEFT BLANK

1-1

0250 Series

Section 1 Introduction

Installation and Operation Manual

X-SE-0250-Series-eng

Part Number: 541B129AAG

October, 2017

1-1 Description

The Brooks Model 0250 Series is a versatile full-featured measurement

and control process instrument, available with single or multiple channel

capabilities. The architecture supports a wide range of operating

capabilities organized to meet the requirements of nearly any high-

accuracy measurement and control application.

This system suits applications requiring advanced single & multiple

channel operation. It provides control services including rate, batch, and

proportional blending.

The system is all digital, based on microcomputer technology. There is no

power switch to be left off, no feature selection switches or jumpers, and

no analog trimming potentiometers.

It employs surface mount technology and incorporates floating-point digital

signal processing arithmetic. Built-in test capabilities enable simple

installation, and extensive self-tests ensures long-term operating reliability.

The rugged package is modular, providing an ideal solution for use in

demanding applications and tough environments. Options are available for

panel mount, desktop & rack mount (0254 only).

1-1-1 Architecture

The system is built on the basics of a multiple-port based architecture,

modularly organized, which are combined as channels, able to meet

present and future instrumentation requirements.

Channel(s) provide for value measurements and quantity accumulation,

rate measurements, scalar measurements, supported by value scaling for

process voltage and current process signals. Signal acquisition uses digital

signal processing rejecting ambient noise and interference.

1-1-2 Communication

The communication facilities provide for data acquisition, command, and

control functions, supporting configuration programming and information

gathering.

Communication is initiated by command (solicited), alarms (unsolicited) &

real time scheduled reporting using its internal date-time clock.

1-1-3 Process Controls

Totalizer, batch, and proportional blending (0254 only) are readily achieved

using the front panel key controls or serial commands.

1-2

0250 Series

Section 1 Introduction

Installation and Operation Manual

X-SE-0250-Series-eng

Part Number: 541B129AAG

October, 2017

1-1-4 Operator Controls and Indicators

The instrument has no power switch to be accidently turned off. Operation

may be completely controlled from its integral eight-key pad used to view

operation and programmed operating values. Key activations are single

touch with hold-and-repeat capability. The front panel key pad provides

splash proofing and environment protection.

The 0250 Series primary indicator is its large back lit liquid crystal graphic

display - visible at a distance even in low light conditions - to view values,

support programming operations, and indicate process state information. A

user-selectable audio indicator annunciates key activations.

1-1-5 Diagnostic Capabilities

Powerful automatic diagnostics support easy installation and ensure a

trouble-free operating life. Tests include memory facility scans, channel

input-output status, and communication status.

1-2 Specifications (Reference Table 1-1)

1-3

0250 Series

Section 1 Introduction

Installation and Operation Manual

X-SE-0250-Series-eng

Part Number: 541B129AAG

October, 2017

Table 1-1 Specifications - 0250 Series

PerformancePerformance

Performance

DisplayDisplay

Display 0251: 8 line x 20 character back-lit LCD display.

0254: 8 line x 40 character back-lit LCD display.

ControlsControls

Controls Keypad: 8-Key metal dome tactile push buttons with selectable audio beep for setpoint (rate, batch, blend),

VOR, emergency stop, full operation and programming.

Date RetentionDate Retention

Date Retention Non-volatile ram/rom, 100 year retention.

Power InputPower Input

Power Input Voltage: 12-24 Vdc required, -15 Vdc permitted.

Current: 400 mA max. current draw per channel.

Instrument power draw: 0.8 Watts.

Optional power module: 100-240 Vac, 47-63Hz.

Power OutputPower Output

Power Output +15 V/2.0 A, -15 V/1.0 A or 12-24 Vdc/2.0 A.

Signal InputSignal Input

Signal Input 0(1)-5 Volts, 0(2)-10 Volts, 0(4)-20 mA.

Signal OutputSignal Output

Signal Output 0(1)-5 Volts, 0(2)-10 Volts, 0(4)-20 mA.

CommunicationsCommunications

Communications Full communications capability for remote readout, setpoint, control, programming and data acquisition via RS232.

EnclosureEnclosure

Enclosure ABS cycolac resin.

Mounting OptionsMounting Options

Mounting Options Panel mount kit, table top kit, rack mount kit, rack mount kit with 19” sub-rack. (Rack mount available for 0254 only)

DimensionsDimensions

Dimensions See product dimensions on pages 4 - 6.

Temperature/HumidityTemperature/Humidity

Temperature/Humidity Operating: 32-122°F (0-50°C), 0-95% non-condensing.

Ship/Storage: (-)40-185°F (-)40-85°C, 0-95% non-condensing.

CertificationsCertifications

Certifications CE Mark

EMC Directive 2014/30/EU EN:61326-1:2013

Low Voltage Directive 2014/35/EU EN:61010-1-2010

Machinery Directive 2006/42/EC EN/ISO:13849-1:2009, EN:60204-1:2009

RoHS Directive 2011/65/EU

FCC Part 15 Class A, part 68

UL-USA & Canada 0254: UL 61010 Electrical Safety for General Purpose Indoor Use.

1-4

0250 Series

Section 1 Introduction

Installation and Operation Manual

X-SE-0250-Series-eng

Part Number: 541B129AAG

October, 2017

1-3 Signal Wiring (Reference Figures 1-1 and 1-2)

1-4 Optional Equipment

1-4-1 Mounting Kit Options

The 0250 Series can be mounted using the following kits:

Panel Mount Kit: Brackets accept panel thickness up to 0.25 in. (6.35 mm).

Table Top Kit: Weighted base with fixed tilt for easy viewing.

Rack Mount Kit: Hardware for mounting the Model 0254 and optional

power supply into 19-in. sub-rack.

Rack Mount Kit with 19-in. sub-rack: 19-in. sub-rack included with Rack

Mount Kit (Model 0254 only).

Retrofit Applications, Model 0152/0154: Rack Mount Kit will adapt the

Model 0254 and power supply to the table top enclosure used for the

Model 0152/0154.

1-4-2 Power Supply Options

The 0250 Series supports the following power supply options:

• Factory supplied: +15 Vdc/2 A, –15 Vdc/1 A, 100–240 Vac, 47–63 Hz

• Factory supplied: +24 Vdc/2.5 A, 100–240 Vac, 47–63 Hz

• User supplied: 12–24 Vdc into 9-pin D connector, 5 A rated

1-4-3 Input/Output Pin-Out Adapters

The Model 0251 has one 15-pin female D-channel connector.

The Model 0254 has four 15-pin female D-channel connectors. The pin

configuration is compatible with standard Brooks 0(4)-20 mA cables.

An optional pin-out adapter kit with four adapters is available for use with

Brooks 0(1)-5 Vdc cables.

1-5

0250 Series

Section 1 Introduction

Installation and Operation Manual

X-SE-0250-Series-eng

Part Number: 541B129AAG

October, 2017

Figure 1-1 Model 0251 Signal Wiring

Figure 1-2 Model 0254 Signal Wiring

1-6

0250 Series

Section 1 Introduction

Installation and Operation Manual

X-SE-0250-Series-eng

Part Number: 541B129AAG

October, 2017

THIS PAGE WAS

INTENTIONALLY

LEFT BLANK

2-1

0250 Series

Section 2 InstallationInstallation and Operation Manual

X-SE-0250-Series-eng

Part Number: 541B129AAG

October, 2017

2-1 General

This section provides installation instructions for the 0250 Series Gas and

Liquid Mass Flow Secondary Electronics device.

2-2 Receipt of Equipment

When the equipment is received, the outside packing case should be

checked for damage incurred during shipment. If the packing case is

damaged, the local carrier should be notified at once regarding his liability.

A report should be submitted to the nearest Brooks Instrument location

listed on the Global Service Network page on our website:

BrooksInstrument.com/GlobalSupportCenters

2-3 Recommended Storage Practice

If intermediate or long-term storage of equipment is required, it is

recommended that the equipment be stored in accordance with the

following:

• Within the original shipping container.

• Stored in a sheltered area, preferably a warm, dry, heated warehouse.

• –40 to 185°F (–40 to 85°C); 0 to 95% non-condensing.

• Upon removal from storage, a visual inspection should be conducted to

verify the condition of equipment is "as received".

2-2

0250 Series

Section 2 Installation Installation and Operation Manual

X-SE-0250-Series-eng

Part Number: 541B129AAG

October, 2017

2-4 Return Shipment

Prior to returning any instrument to the factory for any reason, visit our

website for instructions on how to obtain a Return Materials Authorization

Number (RMA #) and complete a Decontamination Statement to

accompany it: BrooksInstrument.com/Service. All instruments returned to

Brooks also require a Material Safety Data Sheet (MSDS) for the fluid(s)

used in the instrument. Failure to provide this information will delay

processing of the instrument.

2-5 Transit Precautions

To safeguard against damage during transit, transport the instrument to the

installation site in the same container used for transportation from the

factory if circumstances permit.

2-6 Removal from Storage

Upon removal from storage, a visual inspection should be conducted to

verify the condition of the equipment is “as received.”

2-7 Ventilation and Mounting Requirements

Because of their low power consumption, the 0250 Series devices do not

have ventilation requirements. However, the ambient temperature

surrounding the 0251 Series devices should not exeed 122°F (50°C). The

optional power supply modules are also ventilation-free and limited to an

ambient temperature of 122°F (50°C).

2-8 Cleaning Instructions

Do not use cleaning agents other than water because this might affect

color and marking of the equipment.

Use a clean, soft and damp cloth for cleaning.

2-3

0250 Series

Section 2 InstallationInstallation and Operation Manual

X-SE-0250-Series-eng

Part Number: 541B129AAG

October, 2017

2-9 Cable Requirements

For compliance with the EMC directive 89/336/EEC, the equipment has to

be installed with shielded signal cables which are overall completely

screened with a shield of at least 80%. Sub-D connectors used must be

shielded with a metal shield. The cable screen should be connected to the

metal shell and shielded at both ends over 360°. The shield should be

terminated to earth ground.

The optional power supplies available from Brooks are always supplied

with a power cord that meets all agency certifications and has a protective

conductor for grounding purposes. Any replacement cords must have

similar construction and be certified by a recognized nartional test

laboratory.

2-10 Installation Instructions

Do not use cleaning agents other than water because this might affect

color and marking of the equipment.

2-10-1 Panel Mount Installation Instructions

1. Cut a hole according to the cut-out dimensions shown in Figure 2-1 .

2. Pass the 0250 Series device enclosure through the cut-out.

3. Position one of the two brackets included in the Panel Mount kit on the

side of the enclosure, while aligning the two holes at the top and bottom

of the bracket flange with the holes at the corners of the back of the

enclosure. Secure the bracket to the enclosure with two of the screws

provided in the kit.

Do not over-tighten these attachment screws.

CAUTION

!

4. Secure the second bracket to the other side of the enclosure.

5. Tighten the panel mounting screws in the middle of both brackets to

secure the enclosure to the panel.

Do not over-tighten these attachment screws.

CAUTION

!

6. Connect the power supply cable with the D-connector to the power

connector on the back of the enclosure.

7. Connect the power supply AC cord to a power outlet.

8. Connect the cables to the RS232 and Channel connectors, as

approprate for the application.

2-4

0250 Series

Section 2 Installation Installation and Operation Manual

X-SE-0250-Series-eng

Part Number: 541B129AAG

October, 2017

Figure 2-1 Panel Mount Cut-Out Dimensions

Model 0251

Model 0254

2-5

0250 Series

Section 2 InstallationInstallation and Operation Manual

X-SE-0250-Series-eng

Part Number: 541B129AAG

October, 2017

2-10-2 Table Top Stand Assembly Instructions

1. Attach the four rubber mounting feet to the base, as shown in

Figure 2-2.

2. Use four of the provided screws to attach the two brackets to the base.

3. Slide the 0250 Series device enclosure into the brackets.

4. Use four screws to secure the enclosure to the brackets.

Do not over-tighten these attachment screws.

CAUTION

!

5. Connect the power supply cable with the D-connector to the power

connector on the back of the enclosure.

6. Connect the power supply AC cord to a power outlet.

7. Connect the cables to the RS232 and Channel connectors, as

approprate for the application.

2-6

0250 Series

Section 2 Installation Installation and Operation Manual

X-SE-0250-Series-eng

Part Number: 541B129AAG

October, 2017

Figure 2-2 Table Top Stand Mount Installation

Model 0251

Model 0254

Pagina se încarcă ...

Brooks 0251 / 0254 Instrucțiuni de utilizare

Brooks 0251 / 0254 Instrucțiuni de utilizare

în alte limbi

Lucrări conexe

Alte documente