Parkside PABS 18-LI B2 Instrucțiuni de utilizare

Marca: Parkside

Model: PABS 18-LI B2

Categorie: Burghie combinate fără fir

Tip: Instrucțiuni de utilizare

Acest manual este potrivit și pentru

IAN 75636

IAN 75636

CORDLESS DRILL PABS 18-Li B2

AKKU-BOHRSCHRA UBER

Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung

AKU ODVIJAČ

Upute za posluživanje i za Vašu sigurnost

Prijevod originalnih uputa za uporabu

MAȘINĂ DE ÎNȘURUBAT CU

A CUMULATOR

Instrucţiuni de utilizare şi de siguranţă

Traducerea instrucţiunilor de utilizare originale

CORDLESS DRILL

Operation and Safety Notes

Translation of original operation manual

GB Operation and Safety Notes Page 5

HR Upute za posluživanje i za Vašu sigurnost Stranica 17

RO Instrucţiuni de utilizare şi de siguranţă Pagina 27

DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 39

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the

device.

Prije nego što pročitate tekst, otvorite stranicu sa slikama i upoznajte se na osnovu toga sa svim funkcijama

uređaja.

Înainte de a citi instrucţiunile, priviţi imaginile şi familiarizaţi-vă cu toate funcţiile aparatului.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

A B

1413

1617

5 GB

Table of contents

Introduction

Intended purpose ................................................................................................................................ Page 6

Equipment Components ......................................................................................................................Page 6

Scope of delivery ................................................................................................................................Page 7

Technical Data ....................................................................................................................................Page 7

General safety advice for electrical power tools

1. Workplace safety ...........................................................................................................................Page 8

2. Electrical safety ............................................................................................................................... Page 8

3. Personal safety ................................................................................................................................Page 8

4. Careful handling and use of electrical power tools .....................................................................Page 9

5. Use and handling of the cordless electrical power tool ..............................................................Page 9

6. Service .............................................................................................................................................Page 10

Safety advice relating to cordless drill drivers ..................................................................................Page 10

Attention - Service lines! ......................................................................................................................Page 10

Original ancillaries / accessories .......................................................................................................Page 10

Before first use

Charging the battery pack .................................................................................................................Page 10

Insertion / removal of a battery pack into the appliance ..................................................................Page 11

Checking battery status ......................................................................................................................Page 11

Changing tools .................................................................................................................................... Page 11

Torque pre-selection ............................................................................................................................Page 11

2 Gear Drive .......................................................................................................................................Page 12

Preparing the tool for use

Switching On / Off .............................................................................................................................. Page 12

Switching the LED light on and off .....................................................................................................Page 12

Adjusting the speed ............................................................................................................................Page 12

Switching direction of rotation ...........................................................................................................Page 12

Tips and Tricks ..................................................................................................................................... Page 12

Cleaning and Maintenance ..............................................................................................Page 13

Service ...............................................................................................................................................Page 13

Warranty .........................................................................................................................................Page 13

Disposal ............................................................................................................................................Page 14

Conformity Declaration / Manufacturer ................................................................Page 15

6 GB

Introduction

Introduction / General safety advice for electrical power tools

Cordless drill PABS 18-Li B2

Introduction

We congratulate you on the purchase of

your new device. You have chosen a

high

quality product. The instructions for use

are part of the product. They contain important in-

formation concerning safety, use and disposal. Be-

fore using the product, please familiarise yourself

with all of the safety information and instructions

for use. Only use the unit as described and for the

speciﬁed applications. If you pass the product on

to anyone else, please ensure that you also pass

on all the documentation with it.

Intended purpose

This appliance is designed for drilling and screwing

into wood, plastic and metal. Use the appliance only

as described and only for the purposes indicated.

Any other uses, and modiﬁcations to the appliance,

are deemed to be improper usage and may result

in serious physical injury. The manufacturer accepts

no responsibility for damage(s) resulting from

improper usage. The appliance is not intended for

commercial use.

Equipment Components

Gear selector switch

Direction of rotation switch / lock

ON / OFF Switch / R.P.M. regulator

Bit holder

Belt clip

The following pictograms are used in these operating instructions / on the device:

Read instruction manual! Safety class II

Observe caution and safety notes! Drill chuck, Made In Germany

Caution – electric shock!

Danger to life!

Spindle lock

Explosive material! Drill setting (torque preselect)

Watts (Eﬀective power) Wear ear protection.

Design no-load speed

Keep children away from electrical

power tools!

Voltage For indoor use only!

Amp (Battery capacity)

Check that the device, mains lead

and plug are in good condition!

Newton metre (torque)

Dispose packaging and appliance in

an environmentally-friendly way!

DC (current and voltage type)

Do not dispose of rechargeable

batteries with your household refuse!

7 GB

Introduction

Rechargeable battery pack

Battery pack release button

LED light button

LED light

Rechargeable battery display LED

Rechargeable battery charge state button

LED working light

Drill chuck

Torque pre-selector

Fast charger

Red charge-control LED

Green charge-control LED

Scope of delivery

1 Cordless drill with rechargeable battery pack

1 Bit PH2 50 mm

1 Fast charger

1 Carry case

1 Directions for use

Technical Data

PABS 18-Li B2 Cordless drill:

Nominal voltage: 18 V

Idle-running speed: 1st gear: max. 400 min

-1

Idle-running speed: 2nd gear: max. 1400 min

-1

Drill chuck

clamping range: max. 10 mm

Maximum

drill diameter: Steel: 10 mm,

Wood: 30 mm

Max. torque: 35 Nm

PABS 18-Li B2-1 Battery Pack:

Type: LITHIUM-ION

Nominal voltage: 18 V

Capacity: 1.5 Ah

Energy content: 27 Wh

PABS 18-Li B2-2 Fast Charger:

INPUT

Nominal voltage: 230 V∼, 50 Hz

Power input: 55 W

OUTPUT

Nominal voltage: 18 V

Charging current 2 A

Charging time: approx. 60 min

Protection class: II /

Noise and vibration data:

Measured values for noise are determined in accor-

dance with EN 60745. The A-weighted noise level

of the electrical power tool are typically:

Sound pressure level: 76 dB(A)

Sound power level: 87 dB(A)

Uncertainty K: 3 dB

Total vibration (vector sum of three directions) is

calculated in accordance with EN 60745:

Screwing: Vibration emission value

h,D

= 0.865 m / s

uncertainty K = 1.5 m / s

Drilling: Vibration emission value

= 2.546 m / s

uncertainty K = 1.5 m / s

The vibration level speciﬁed in

these instructions was measured in accordance with

an EN 60745 standardised measurement process

and can be used to compare equipment. The vibra-

tion emission value speciﬁed can also serve as a

preliminary assessment of the exposure.

The vibration level will change according to the ap-

plication of the electrical tool an in some cases may

exceed the value speciﬁed in these instructions. Re-

gularly using the electric tool in such a way may

make it easy to underestimate the vibration.

Note: If you wish to make an accurate assessment

of the vibration loads experienced during a particular

period of working, you should also take into account

the intervening periods of time when the device is

switched oﬀ or is running but is not actually in use.

This can result in a much lower vibration load over

the whole of the period of working.

Introduction / General safety advice for electrical power tools

8 GB

General safety advice for

electrical power tools

Read all the safety advice

and instructions! Failure to observe the safety

advice and instructions may result in electric shock,

ﬁre and / or serious injury.

Keep all the safety advice and instructions

in a safe place for future reference!

The term “electrical tool” used in the safety advice

refers to electrical tools powered by mains electrici-

ty (by means of a mains lead) and electrical tools

mains lead).

Workplace safety

a) Keep your working area clean and

well lit. Untidy or poorly lit working areas

can lead to accidents.

Do not work with the device

in potentially explosive envi-

ronments in which there are

inflammable liquids, gases or dusts.

Electrical power tools create sparks, which can

ignite dusts or fumes.

Keep children and other

people away while you are

operating the electrical tool.

Distractions can cause you to lose control of

the device.

Electrical safety

The mains plug on the device must match

the mains socket. The plug must not

be modified in any way. Do not use

an adapter plug with devices fitted

with a protective earth. Unmodiﬁed

plugs and matching sockets reduce the risk of

electric shock.

b) Avoid touching earthed surfaces such

as pipes, radiators, ovens and refrig-

erators with any part of your body.

There is an increased risk of electric shock if

your body is earthed

c) Keep the device away from rain or

moisture. Water entering an electrical device

increases the risk of electric shock.

Do not use the mains lead for

any purpose for which it was

not intended, e.g. to carry the

device, to hang up the device or to pull

the mains plug out of the mains socket.

Keep the mains lead away from heat,

oil, sharp edges or moving parts of the

device. Damaged or tangled mains leads

increase the risk of electric shock.

e) When working outdoors with an

electrical power tool always use ex-

tension cables that are also approved

for use outdoors. The use of an extension

cable suitable for outdoor use reduces the risk

of electric shock.

f) Use a residual current device (RCD)

for protection if operating the electri-

cal power tool in a moist environment

is unavoidable. The use of an RCD reduces

the risk of electric shock.

3. Personal safety

a) Remain alert at all times, watch what

you are doing and always proceed

with caution. Do not use the device if

you are tired or under the influence of

drugs, alcohol or medication. One mo

ment

of carelessness when using the device can lead

to serious injury.

b) Wear personal protective equipment

and always wear safety glasses. The

wearing of personal protective equipment such

as dust masks, non-slip safety shoes, safety

helmets or ear protectors, appropriate to the

type of electrical power tool used and work

undertaken, reduces the risk of injury.

c) Avoid unintentional operation of the

device. Check that the electrical power

tool is switched off before you connect

it to the mains, pick it up or carry it.

Accidents can happen if you carry the device

General safety advice for electrical power tools

9 GB

with your ﬁnger on the ON / OFF switch or with

the device switched on.

d) Remove any setting tools or spanners

before you switch the device on. A tool

or spanner left attached to a rotating part of a

device can lead to injury.

e) Avoid placing your body in an unnat-

ural position. Keep proper footing

and balance at all times. By doing this

you will be in a better position to control the

device in unforeseen circumstances.

f) Wear suitable clothing. Do not wear

loose clothing or jewellery. Keep your

hair, clothing and gloves clear of mov-

ing parts. Loose clothing, jewellery or long

hair can become trapped in moving parts.

g) If vacuum dust extraction and collection

devices are fitted do not forget to

check

that they are properly connected and

correctly used. The use of these devices

reduces the hazard presented by dust.

Careful handling and use

of electrical power tools

a) Do not overload the device. Always

use an electrical power tool that is

intended for the task you are under-

taking. By using the right electrical power

tool for the job you will work more safely and

achieve a better result.

b) Do not use an electrical power tool if

its switch is defective. An electrical power

tool that can no longer be switched on and oﬀ

is dangerous and must be repaired.

c) Pull the mains plug out of the socket

and / or remove the rechargeable bat-

tery before you make any adjustments

to the device, change accessories or

when the device is put away. This pre-

caution is intended to prevent the device from

unintentionally starting.

d) When not in use always ensure that

electrical power tools are kept out of

reach of children. Do not let anyone use

the device if he or she is not familiar

with it or has not read the instructions

and advice. Electrical power tools are dan-

gerous when they are used by inexperienced

people.

e) Look after the device carefully. Check

that moving parts are working prop-

erly and move freely. Check for any

parts that are broken or damaged

enough to detrimentally affect the

functioning of the device. Have dam-

aged parts repaired before you use

the device. Many accidents have their origins

in poorly maintained electrical power tools.

f) Keep cutting tools clean and sharp.

Carefully maintained cutting tools with sharp

cutting edges are less likely to jam and are

easier to control.

g) Use the electrical power tool, accesso-

ries, inserted tools etc. in accordance

with these instructions and advice, and

the stipulations drawn up for this par-

ticular type of device. In doing this, take

into account the working conditions

and the task in hand. The use of electrical

power tools for purposes other than those in-

tended can lead to dangerous situations.

5. Use and handling of the cord-

less electrical power tool

a) Charge a rechargeable battery unit

using only the charger recommended

by the manufacturer. Chargers are often

designed for a particular type of rechargeable

battery unit. There is the danger of ﬁre if other

types of rechargeable battery units are used.

Only the rechargeable battery units su

plied are to be used with an electrical

power tool. The use of other rechargeable bat-

ery units may lead to the danger of injury or ﬁre.

c) When they are not being used, store

rechargeable battery units away from

paperclips, coins, keys. nails, screws

or other small metal objects that could

cause the contacts to be bridged. Short-

circuiting the contacts of a rechargeable battery

unit may result in heat damage or ﬁre.

General safety advice for electrical power tools

10 GB

Fluids may leak out of rechargeable

battery units if they are misused. If

this happens, avoid contact with the

ﬂuid. If contact occurs, ﬂush the aﬀect-

ed area with water. Seek additional

medical help if any of the ﬂuid gets

into your eyes. Escaping battery ﬂuid may

cause skin irritation or burns.

CAUTION! DANGER OF EX-

PLOSION! The batteries must

never be recharged!

6. Service

a) Have your device repaired at the ser-

vice centre or by qualified specialist

personnel using original manufacturer

parts only. This will ensure that your device

remains safe to use.

Safety advice relating

to cordless drill drivers

Hold the device by the

insulated handle surfaces when you

are undertaking work where there is

the danger of the screw striking hidden

electricity cables or the device’s mains

lead. Contact of the screw with a live wire could

cause metal parts of the device to become live

and lead to electric shock.

Children or persons who lack the knowledge or

experience to use the device or whose physical,

sensory or intellectual capacities are limited

must never be allowed to use the device without

supervision or instruction by a person responsi-

ble for their safety. Children must never be

allowed to play with the device.

Securely support the workpiece. A workpiece

held in a clamp or vice is kept more securely in

place than one held by your hand.

POISONOUS DUSTS!

Harmful / noxious dusts generated from your

work represent a risk to the health of the person

operating the device and to anyone near the

work area. Wear safety glasses and a dust mask!

Do not drill any material containing

asbestos. Asbestos is a known carcinogen.

Hold the electrical power tool ﬁrmly.

High reaction torques may occur momentarily

during tightening or loosening of screws.

If the inserted tool jams, switch oﬀ the

electrical power tool immediately. Be

prepared for high reaction torques as they may

cause kickback. The inserted tool may jam if

the electrical power tool is overloaded or is

held at an angle to the workpiece.

Before you carry out any tasks on the

device, transport or store it, make sure

that the direction of rotation switch is

in the middle position (lock). To prevent

the device from starting up unintentionally.

Attention - Service lines!

DANGER! Take steps to ensure that

you do not hit upon any service lines

(electricity, gas, water) when work-

ing with electrical appliances. Check, if

need be with a service line detector, before

you start to cut or bore into a surface.

Original ancillaries /

accessories

Use only the ancillaries and accessories

that are detailed in the operating

instructions. The use of ancillaries and ac-

cessories other than those recommended in the

operating instructions could lead to an increased

risk of personal injury for you.

Before ﬁrst use

Charging the battery pack

DANGER OF ELECTRIC

SHOCK! Before cleaning or servicing the

charging station or the battery pack always

ensure that the plug is not in the mains socket.

Before first use

General safety advice for electrical power tools / Before first use

11 GB

Note! A new battery pack, or one that has not

been in use for an extended period, must be charged

up before the ﬁrst / renewed usage.

The battery pack attains its full capacity after ca.

3–5 charging cycles.

CAUTION! Always ensure the plug is removed

from the mains socket before inserting a battery pack

into, or removing one from, the charging station.

Never charge the battery pack if the ambient

temperature is less than 10 °C or greater than

40 °C.

1. Insert the battery pack

into the quick-

charger

(see Fig. C).

2. Insert the mains plug into the mains socket. The

ﬂashing green charge indicator LED

shows

that charging is in progress.

3. The charging process is completed when the

green charge indicator LED

light up and the

accumulator pack

is ready for operation.

4. If the red charge indicator LED

lights up, the

quick battery charger

is in standby mode;

the accumulator pack

is not connected.

5. If the red charge indicator LED

starts ﬂas-

hing, this means that the accumulator pack

has become too hot; no charging process.

Never charge the battery pack for a second time

immediately after a fast charging process has

been completed. This can give rise to the battery

pack becoming overcharged and to a reduced

service life of the battery and charging station.

Switch the charger oﬀ for at least 15 minutes

between two successive charging procedures.

Remove the power plug from the wall socket.

Insertion / removal of a battery

pack into the appliance

Ensure that the appliance is switched oﬀ before in-

serting the battery. The insertion of a battery into an

electrical appliance that is switched on can lead to

accidents.

Inserting the rechargeable battery pack:

Move the rotation switch

into the middle

position (lock) and push the rechargeable bat-

tery pack

into the handle until it engages.

Removing the rechargeable battery pack:

Press the release button

and remove the

rechargeable battery pack

Checking battery status

To check the battery status, press the battery

LED button

(refer to main diagram). The

status or residual capacity will be indicated in

the battery LED

as follows:

GREEN / RED / ORANGE = maximum charge /

capacity

RED / ORANGE = medium charge / capacity

RED = weak charge – recharge battery

Changing tools

Your cordless electric drill / screwdriver has a fully

automatic spindle lock

and is ﬁtted with an

enclosed keyless chuck incorporating the latest

technology from

”Made in Germany”.

Once the motor has come to a halt, the drive shaft

is automatically locked, so that the chuck

can

be opened simply by turning it

After you have inserted the required bit and ﬁxed it

in place by turning the chuck

, you can immedi-

ately continue working. The spindle lock releases

itself automatically when the motor is started (by

operation of the ON / OFF switch

Torque pre-selection

You can adjust the torque by using

torque pre-

selection. The torque levels regulate a range of up

to ca. 35 Nm.

Select a low setting for small screws, soft work

material.

Before first use

General safety advice for electrical power tools / Before first use

12 GB

Select a high setting for large screws, hard

work materials and for the extraction of screws.

For drilling, push the selector to the setting for

drilling, in that you adjust the torque pre-selector

to the position

For drilling tasks, also push the gear selector

switch

to the front (Position: 2).

2 Gear Drive

CAUTION! Move the gear selector switch

only after the device has come to a standstill.

Failure to observe this advice may result in damage

to the device.

In the ﬁrst gear (Gear selector switch

in Position: 1)

A speed of up to approx. 400 rpm can be achieved

and a high torque. This setting is intended for use w

ith

all screwing tasks and for accessories (see example

Fig. B).

In the second gear (Gear selector switch

in Position: 2)

It achieves a speed of up to approx. 1400 rpm, for

the carrying out of drilling tasks (see example Fig. A).

Preparing the tool for use

Switching ON /OFF

Switching on:

To start the appliance squeeze on the ON /

OFF switch

and then keep it pressed down.

The LED working light

comes on with a slightly

or fully pressed ON /OFF switch

and illumi-

nates the working area in poor lighting conditio

ns.

Switching off:

To stop the appliance, release the ON / OFF

switch

Switching the LED light on and oﬀ

Switching on:

Press the LED light button

to switch on the

LED light

Switching off:

Press the LED light button

again to switch

oﬀ the LED light

Adjusting the speed

The ON / OFF switch

has a variable speed con-

trol device. Slight pressure on the ON / OFF switch

will cause the rotation speed to slow down. With

increased pressure, the rotational speed will increase.

Note: The integrated engine brake means that the

device will come to a fast standstill.

Switching direction of rotation

To switch the direction of rotation, push the

direction of rotation switch

to either the

right or to the left.

Tips and Tricks

Before you use the appliance, check to see

that the screw or drill bit is properly ﬁtted, i.e.

located centrally in the chuck.

Screw bits are designated with their dimensions

and their shape. If you are unsure, always try

the particular screw bit out to see whether it sits

in the screw head without any free play.

Torque:

Smaller screws and bits in particular can be

easily damaged if you adjust the appliance

with too high a torque and/or rotation speed.

Hard screwdriving conditions (into metal):

Particularly high torques can occur, for example

with metal screws tightened by socket tool bits.

Select a lower rotation speed.

Before first use / Preparing the tool for use

13 GB

Preparing the tool for use / Cleaning and Maintenance / Service / Warranty

Soft screwdriving conditions (e.g. into

soft wood):

You should also select a low speed in order not to

damage the wood workpiece surface through con-

tact with the metal screw head. Use a countersinker.

When drilling into wood, metal and other

materials, take note of the following advice:

With small diameter drill bits use a high drill

speed. For large diameter drill bits, use a low

drill speed.

For hard materials, select a low drill speed.

For soft materials, select a high drill speed.

Secure or ﬁx down the workpiece (if possible)

in a clamp or vice.

Mark the intended position of the hole with a

centre punch or a nail and select a low drill speed

for drilling.

Take the rotating drill bit out of the hole frequently

so that swarf or drill dust can be re-moved and

the hole and tool is ventilated.

Drilling in metal:

Use a metal drill bit (HSS). For the best results,

you should cool the bit with oil. Metal drill bits

can also be used to drill into plastic.

Drilling in stone:

Use a circular shafted masonry drill bit with a

hardened metal tip.

Drilling in wood:

Normally you should use a wood drill with a

centring point. For deep holes, use an auger type

bit. For large diameter holes, use a forstner bit.

You can screw small screws into soft wood

without the need for pre-drilling.

Cleaning and Maintenance

CAUTION! Place the direction of rotation

switch

into the middle position before carry-

ing out any tasks on the device, e.g. changing

tools or maintenance, or before transporting or

storing the device. Inadvertent operation of the

ON / OFF switch

may result in injury.

Pull the mains lead out of the mains socket eve-

ry time and remove the battery before you clean

or maintain the device.

The Cordless drill is maintenance-free.

Always keep the device clean, dry and free of

oil or grease.

Clean the device immediately after you have

ﬁnished using it.

Do not allow any liquids to enter the device.

Use a cloth to clean the housing. Never use

petrol, solvents or cleaning agents that might

attack plastic.

Service

Have your device repaired

at the service centre or by qualified

specialist personnel using original

manufacturer parts only. This will ensure

that your device remains safe to use.

If the plug or lead needs

to be replaced, always have the

replacement carried out by the manu-

facturer or its service centre. This will

ensure that your device remains safe to use.

Warranty

The warranty for this appliance is for 3

years from the date of purchase. The ap-

pliance has been manufactured with care

and meticulously examined before deliv-

ery. Please retain your receipt as proof

of purchase. In the event of a warranty

claim, please make contact by telephone

with our Service Department. Only in this

way can a post-free despatch for your

goods be assured.

The warranty covers only claims for material and

maufacturing defects, but not for transport damage,

for wearing parts or for damage to fragile compo-

nents, e.g. buttons or batteries. This product is for pri-

vate use only and is not intended for commercial use.

Before first use / Preparing the tool for use

14 GB

Warranty / Disposal

The warranty is void in the case of abusive and im-

proper handling, use of force and internal tamper-

ing not carried out by our authorized service branch.

Your statutory rights are not restricted in any way

by this warranty.

The warranty period will not be extended by repairs

made unter warranty. This applies also to replaced

and repaired parts. Any damage and defects extant

on purchase must be reported immediately after

unpacking the appliance, at the latest, two days after

the purchase date. Repairs made after the expiration

of the warranty period are subject to payment.

Service Great Britain

Tel.: 0871 5000 720

(0,10 GBP/Min.)

e-mail: k[email protected]

IAN 75636

Disposal

The packaging comprises exclusively en-

vironmentally-friendly material. Dispose

of it in your local recycling containers.

Do not dispose of electrical

appliances with your domestic

waste!

According to the European Directive 2002 / 96 / EC,

concerning used electrical and electronic appliances

and its implementation in national law, superannu-

ated electrical appliances must be collected and

disposed of via an environmentally suitable recy-

cling facility.

Do not dispose of rechargeable

batteries with your household

refuse!

Defective or worn out rechargeable batteries must

be recycled according to Directive 2006 / 66 / EC.

Dispose of batteries and appliances over the existing

collection facilities.

Your local communal or municipal authorities can

provide information on how to dispose of the worn

out appliance.

15 GB

Conformity Declaration / Manufacturer

Conformity Declaration /

Manufacturer

We, Kompernaß GmbH, the person responsible for

documents: Mr Semi Uguzlu, Burgstr. 21, D-44867

Bochum, Germany, hereby declare that this product

complies with the following standards, normative

documents and EU directives:

Machinery Directive

(2006 / 42 / EC)

EC Low Voltage Directive

(2006 / 95 / EC)

Electromagnetic compatibility

(2004 / 108 / EC)

Applicable harmonized standards

EN 60745-1:2009+A11

EN 60745-2-1:2010, EN 60745-2-2:2010

EN 55014-1:2006+A1+A2

EN 55014-2:1997+A1+A2

EN 61000-3-2:2006+A1+A2

EN 61000-3-3:2008

EN 60335-1:2002+A1+A11+A12+A2+A13+A14

EN 60335-2-29:2004

EN 62233:2008

Type / Appliance Designation:

Cordless drill PABS 18-Li B2

Date of manufacture (DOM): 07–2012

Serial number: IAN 75636

Bochum, 31.07.2012

Semi Uguzlu

- Quality Manager -

We reserve the right to make technical modiﬁcations

in the course of further development.

Warranty / Disposal

17 HR

Popis sadržaja

Uvod

Uporaba u skladu sa namjenom .................................................................................................. Stranica 18

Oprema ......................................................................................................................................... Stranica 18

Opseg isporuke ............................................................................................................................. Stranica 19

Tehnički podaci ............................................................................................................................. Stranica 19

Opće sigurnosne upute za električni alat

1. Sigurnost na radnom mjestu .................................................................................................... Stranica 20

2. Električna sigurnost ................................................................................................................... Stranica 20

3. Sigurnost osoba ........................................................................................................................ Stranica 20

4. Pažljivo postupanje s električnim uređajima i njihovo korištenje ........................................... Stranica 21

5. Uporaba i rukovanje akumulatorskim alatom ........................................................................ Stranica 21

6. Servis ......................................................................................................................................... Stranica 22

Sigurnosne upute za akumulatorsku bušilicu ............................................................................... Stranica 22

Pažnja, vodovi! ............................................................................................................................. Stranica 22

Originalna oprema / dodatni uređaji .......................................................................................... Stranica 22

Prije stavljanja u rad

Punjenje paketa baterija ............................................................................................................... Stranica 22

Umetanje paketa baterija u uređaj / vađenje paketa baterija ................................................... Stranica 23

Provjeravanje aku-stanja ............................................................................................................... Stranica 23

Zamjena alata ............................................................................................................................... Stranica 23

Određivanje okretnog momenta unaprijed ................................................................................. Stranica 23

2-brzinski mjenjač ......................................................................................................................... Stranica 24

Stavljanje u rad

Uključivanje / Isključivanje ............................................................................................................ Stranica 24

Uključivanje / isključivanje LED-svjetiljke ...................................................................................... Stranica 24

Podešavanje brzine....................................................................................................................... Stranica 24

Promjena smjera okretanja ........................................................................................................... Stranica 24

Savjeti i trikovi ............................................................................................................................... Stranica 24

Održavanje i čišćenje ...................................................................................................... Stranica 25

Servis ............................................................................................................................................ Stranica 25

Jamstveni list.......................................................................................................................... Stranica 25

Zbrinjavanje ........................................................................................................................... Stranica 26

Izjava o sukladnosti / proizvođač ........................................................................ Stranica 27

18 HR

Uvod

Aku odvijač PABS 18-Li B2

Uvod

Čestitamo Vam na kupnji novog uređaja.

Ovom kupnjom odlučili ste se za visokok-

valitetan proizvod. Uputa za uporabu je

sastavni dio ovog proizvoda. Ona sadrži važne

upute o sigurnosti, uporabi i uklanjanju otpada. Prije

upotrebe proizvoda upoznajte se sa svim njegovim

uputama za korištenje i sigurnosnim uputama. Ko-

ristite ovaj proizvod u skladu s navedenim uputama

te u navedene svrhe. Ukoliko proizvod dajete nekoj

drugoj osobi, predajte toj osobi također i sve upute.

Uporaba u skladu sa namjenom

Ovaj uređaj je namijenjen za bušenje i odvijanje u

drvetu, plastici i metalu. Koristite uređaj isključivo

na opisani način i u navedenim područjima primjene.

Svaki drugi način uporabe i svaka promjena uređaja

smatra se nenamjenskom i krije znatnu opasnost od

nastanka nezgode. Proizvođač ne preuzima odgo-

vornost od štete nastale uslijed korištenja uređaja

protivnog njegovoj namjeni. Uređaj nije namjenjen

za komercijalnu uporabu.

Oprema

Prekidač za odabir stupnja brzine

Prekidač za odabir smjera okretanja / blokada

Prekidač Uklj.-Isklj. / Regulator broja okretaja

U ovim uputama za uporabu / na uređaju rabi se slijedeće prikaze:

Čitati upute za rukovanje! Zaštitna klasa II

Obratiti pažnju na upozoravajuće

i sigurnosne upute!

Zaglavnik za svrdlo, Made In Germany

Čuvajte se strujnog udara!

Opasnost po život!

Aretiranje osovine

Opasnost od eksplozije!

Stupanj bušenja

(odabir okretnog momenta)

W (Efektivna snaga) Nosite zaštitu za sluh.

Određivanje broja praznohodne

brzine vrtnje

Držite djecu podalje od

električnog alata!

V (Naizmjenični napon)

Isključivo namijenjeno za uporabu

u unutarnjim prostorijama!

Amper-sati (Kapacitet akumulatora)

Vodite računa o tome, da se ne ošteti

uređaj, mrežni kabel i utikač!

Newton metar (okretni moment)

Materijal ambalaže i uređaj zbrinite

na način neškodljiv za okoliš!

Istosmjerna struja (struja i vrsta napona) Akumulator ne bacajte u kućni otpad!

19 HR

Držač bita

Pričvršćenje pojasa

Komplet akumulatora

Tipka za deblokiranje kompleta akumulatora

Tipka LED-svjetiljke

LED-svjetiljka

LED pokazivača akumutalora

Tipka stanje akumulatora

Radna LED-svjetiljka

Zaglavnik za svrdlo

Regulator za odabir okretnog momenta unaprijed

Uređaj za brzo punjenje

Crvena LED-signalizacija za kontrolu punjenja

Zelena LED-signalizacija za kontrolu punjenja

Opseg isporuke

1 aku bušilica / odvijač s u aku-pakovanjem

1 bit PH2 50 mm

1 uređaj za brzo punjenje

1 kovčeg za nošenje

1 uputstvo za uporabu

Tehnički podaci

PABS 18-Li B2 aku-bušilica/odvijač:

nazivni napon: 18 V

broj okretaja u

praznom hodu: 1. hod: maksimalno

400 min

-1

broj okretaja u

praznom hodu: 2. hod: maksimalno

1400 min

-1

raspon zaglavnika

za svrdlo: maksimalno 10 mm

maksimalan

promjer bušotine: čelik: 10 mm,

drvo: 30 mm

maksimalan

okretni moment: 35 Nm

PABS 18-Li B2-1 aku-pakovanje:

tip: LITHIUM-ION

nazivni napon: 18 V

kapacitet: 1,5 Ah

sadržaj energije: 27 Wh

PABS 18-Li B2-2 uređaj za brzo punjenje:

ULAZ / Input:

nazivni napon: 230 V∼, 50 Hz

potrošnja: 55 W

IZLAZ / Output:

nazivni napon: 18 V

struja punjenja: 2 A

trajanje punjenja: oko 60 min

zaštitna klasa: II /

Informacija o buci i vibraciji:

Mjerna vrijednost za buku utvrđena sukladno

EN 60745. A-ocjenjena razina buke električnog

alata iznosi tipično:

Razina zvučnog tlaka: 76 dB(A)

Razina snage zvuka: 87 dB(A)

Nesigurnost K: 3 dB

Ukupne vrijednosti titranja (vektorski zbroj triju

smjerova) su istražene sukladno EN 60745:

Vijak: Vrijednost emisije titranja

h,D

= 0,865 m / s

Nesigurnost K= 1,5 m / s

Bušenje: Vrijednost emisije titranja

= 2,546 m / s

Nesigurnost K= 1,5 m / s

Razina titranja, navedena u

ovim uputama, je istražena i određena sukladno

normiranom postupku mjerenja, koji je naveden u

EN 60745 i koji je prikladan za uspoređivanje stroja.

Navedena vrijednost emisije titranja se može koristiti

i za uvodnu procjenu izloženosti.

Razina titranja je promijenljiva, ovisno o korištenju

električnog alata, te može u pojedinim slučajevima

ležati iznad vrijednosti, navedene u ovim uputama.

Razina opterećenja titranja može biti podcjenjena,

ako se električni alat redovito koristi na takav način.

Uputa: Za precizno ocjenjivanje titrajnog otpere-

ćenja tijekom određenog radnog vremena, potrebno

je također uzeti u obzir vremena kad je stroj isključen,

ili je uključen ali se zapravo ne rabi. To može znatno

smanjiti titrajno opterećenje, tijekom cijelog radnog

vremena.

Uvod

20 HR

Opće sigurnosne upute za električni alat

Opće sigurnosne upute

za električni alat

Pročitajte sigurnosne

upute kao i sve ostale upute! U slučaju ne

pridržavanja sigurnosnih uputa kao i ostalih uputa,

prijeti opasnost od strujnog udara, požara i / ili teš-

kih ozljeda.

Sačuvajte sve sigurnosne upute kao i sve

ostale upute za ubuduće!

U sigurnosnim uputa rabljeni izraz „električni alat“

odnosi se na električne uređaje sa mrežnim pogo-

nom (sa mrežnim kabelom) i na električni alat sa

akumula

torskim pogonom (bez mrežnog kabela).

Sigurnost na radnom mjestu

a) Vodite uvijek računa o tome, da Vaše

radno mjesto bude čisto i dobro os-

vjetljeno. Nered i ne osvjetljeno područje

rada, može uzrokovati nezgode.

Ne rabite stroj u području gdje

prijeti opasnost od eksplozije,

gdje se nalaze zapaljive teku-

ćine, plinovi ili prašine. Električni alati proiz-

vode iskre, koje mogu zapaliti prašinu ili pare.

vrijeme uporabe elek

trič-

nog alata, držite djecu i druge

osobe izvan dohvata istoga.

U slučaju nepažnje, možete izgubiti kontrolu

nad strojem.

Električna sigurnost

a) Mrežni utikač uređaja mora odgova-

rati utičnici. Utikač se ni na kakav

način ne smije mijenjati. Ne koristite

adapterske utičnice zajedno s zaštitno

uzemljenim uređajima. Neizmijenjeni

utikači i odgovarajuće utičnice smanjuju rizik

električnog udara.

b) Izbjegavajte dodir tijela s uzemljenim

površinama kao što su cijevi, radijato-

ri, pećnice i hladnjaci. Postoji povećana

opasnost od električnog udara ukoliko je vaše

tijelo uzemljeno.

c) Uređaj držite podalje od kiše i vlage.

Prodiranje vode u unutrašnjost uređaja pove-

ćava opasnost električnog udara.

Ne koristite kabel u neke

druge svrhe, npr. za nošenje

uređaja, vješanje uređaja ili

za izvlačenje utikača iz utičnice. Kabel

držite podalje od topline, ulja, oštrih

rubova i pokretnih dijelova uređaja.

Oštećeni ili spetljani kabel ili utikač povećava

rizik električnog udara.

e) Kod rada na otvorenome koristite

samo produžni kabel koji je dozvoljen

za korištenje na otvorenome. Upotreba

produžnog kabla namijenjenog za korištenje

na otvorenome smanjuje rizik električnog udara.

f) Ako je korištenje električnog alata u

vlažnim prostorima neizbježno, rabite

zaštitnu strujnu sklopku. Korištenje zaštit-

ne strujne sklopke, smanjuje rizik strujnog udara.

3. Sigurnost osoba

a) Budite uvijek pozorni, vodite računa

o tome što radite i razumno pristupite

radu s električnim alatom. Ne rabite

stroj, ako ste umorni ili pod utjecajem

droga, alkohola ili lijekova. Jedan trenu

tak

nepažnje za vrijeme korištenja stroja, može

uzrokovati teške ozljede.

b) Nosite osobnu zaštitnu opremu i uvijek

zaštitne očale. Korištenje osobne zaštitne

opreme, kao maske za prašinu, protuklizne

zaštitne cipele, zaštitnu kacigu ili štitnik za uši,

ovisno o vrsti i uporabi električnog alata,

smanjuje rizik od ozljeda.

c) Spriječite slučajno uključenje. Uvjerite

se u to, da je električni alat isključen,

prije uključenja na struju, podizanja

ili nošenja. Ako pri nošenju uređaja držite

prst na sklopki za UKLJUČENJE / ISKLJUČENJE

ili ako je uređaj uključen, prijeti opasnost od

nezgode.

Opće sigurnosne upute za električni alat

Pagina se încarcă ...

Parkside PABS 18-LI B2 Instrucțiuni de utilizare

Marca: Parkside

Model: PABS 18-LI B2

Categorie: Burghie combinate fără fir

Tip: Instrucțiuni de utilizare

Acest manual este potrivit și pentru

IAN 75636

Descărcați PDF

raport

în alte limbi

English: Parkside PABS 18-LI B2 Operating instructions
Deutsch: Parkside PABS 18-LI B2 Bedienungsanleitung

Parkside PABS 18-LI B2 Instrucțiuni de utilizare

Acest manual este potrivit și pentru

Parkside PABS 18-LI B2 Instrucțiuni de utilizare

în alte limbi

Lucrări conexe

Alte documente