Makita LM001J Manual de utilizare

LM001J

LM002J

EN Cordless Lawn Mower INSTRUCTION MANUAL 9

PL Akumulatorowa kosiarka do

trawy INSTRUKCJA OBSŁUGI 21

HU Vezeték nélküli fűnyíró HASZNÁLATI KÉZIKÖNYV 34

SK Akumulátorová kosačka NÁVOD NA OBSLUHU 47

CS Akumulátorová sekačka na

trávu NÁVOD K OBSLUZE 59

UK Бездротова газонокосарка ІНСТРУКЦІЯ З

ЕКСПЛУАТАЦІЇ 71

RO Maşină de tuns iarba fără

cablu MANUAL DE INSTRUCŢIUNI 85

DE Akku Rasenmäher BETRIEBSANLEITUNG 98

1

23

4

Fig.1

1

Fig.2

1

Fig.3

1

Fig.4

1

Fig.5

1

Fig.6

Fig.7

2

Fig.8

1

Fig.9

1

Fig.10

3

2

1

Fig.11

1

2

Fig.12

1

2

Fig.13

3

1

2

Fig.14

1

2

Fig.15

Fig.16

1

Fig.17

1

2 3

Fig.18

12

Fig.19

4

1

2

3

4

5

Fig.20

1 2

Fig.21

1

Fig.22

1

2

Fig.23

1

Fig.24

1

Fig.25

2

1

Fig.26

5

1

Fig.27

1

2

Fig.28

Fig.29

Fig.30

12 3

Fig.31

Fig.32

Fig.33

6

1

3

2

Fig.34

1

2

Fig.35

1

Fig.36

1

Fig.37

2

1

Fig.38

1

Fig.39

7

1

Fig.40

2

1

3

Fig.41

3

2

4

1

Fig.42

8

9ENGLISH

ENGLISH (Original instructions)

SPECIFICATIONS

Model: LM001J LM002J

Mowing width (blade diameter) 480 mm 534 mm

No load speed Normal mode 3,200 min-1 2,800 min-1

Soft no-load mode 2,500 - 3,200 min-1 2,300 - 2,800 min-1

Noise reduction mode 2,500 min-1 2,300 min-1

Part number of replacement

mower blade

Straight mower blade 191V97-3 191V96-5

Mulching blade 191Y64-6 191Y65-4

Dimensions

(L x W x H)

during operation L: 1,610 mm to 1,690 mm

W: 530 mm

H: 930 mm to 1,050 mm

L: 1,710 mm to 1,800 mm

W: 585 mm

H: 950 mm to 1,090 mm

when stored

(without grass basket)

620 mm x 530 mm x 870 mm 620 mm x 585 mm x 930 mm

Rated voltage D.C. 57.6 V - 64 V max

Net weight 24.4 - 26.1 kg 25.5 - 27.3 kg

Protection degree IPX4

•

Due to our continuing program of research and development, the specications herein are subject to change without notice.

• Specications may dier from country to country.

• The weight may dier depending on the attachment(s), including the battery cartridge. The lightest and heavi-

est combination, according to EPTA-Procedure 01/2014, are shown in the table.

Applicable battery cartridge and charger

Battery cartridge BL6440

Charger DC64WA

•

Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.

WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges

and chargers may cause injury and/or re.

Symbols

The followings show the symbols which may be used for the equip-

ment. Be sure that you understand their meaning before use.

Do not expose to moisture.

Take particular care and attention.

Read instruction manual.

Danger; be aware of thrown objects.

The distance between the tool and

bystanders must be at least 15 m.

Never put your hands and feet near the

mower blade under the mower. Mower

blades continue to rotate after the motor is

switched o.

Warning; Disconnect battery before

maintenance.

Remove the lock key before inspecting,

adjusting, cleaning, servicing, leaving and

storing the mower.

Electrical hazard. Contact with water can

cause electric shock.

Do not pour water.

Ni-MH

Li-ion

Only for EU countries

Due to the presence of hazardous com-

ponents in the equipment, waste electrical

and electronic equipment, accumulators

and batteries may have a negative impact

on the environment and human health.

Do not dispose of electrical and electronic

appliances or batteries with household waste!

In accordance with the European Directive on

waste electrical and electronic equipment and on

accumulators and batteries and waste accumu-

lators and batteries, as well as their adaptation to

national law, waste electrical equipment, batteries

and accumulators should be stored separately

and delivered to a separate collection point for

municipal waste, operating in accordance with the

regulations on environmental protection.

This is indicated by the symbol of the crossed-

out wheeled bin placed on the equipment.

10 ENGLISH

Guaranteed sound power level according

to EU Outdoor Noise Directive.

Sound power level according to Australia

NSW Noise Control Regulation.

Intended use

The machine is intended for lawn mowing.

Noise

The typical A-weighted noise level determined accord-

ing to EN60335-2-77:

Model LM001J

Sound pressure level (LpA) : 84.9 dB(A)

Sound power level (LWA) : 92.5 dB (A)

Uncertainty (K) : 3 dB(A)

Model LM002J

Sound pressure level (LpA) : 82.1 dB(A)

Sound power level (LWA) : 91.6 dB (A)

Uncertainty (K) : 3 dB(A)

NOTE:

The declared noise emission value(s) has been

measured in accordance with a standard test method

and may be used for comparing one tool with another.

NOTE:

The declared noise emission value(s) may

also be used in a preliminary assessment of exposure.

WARNING: Wear ear protection.

WARNING:

The noise emission during actual

use of the power tool can dier from the declared

value(s) depending on the ways in which the tool is

used especially what kind of workpiece is processed.

WARNING:

Be sure to identify safety measures

to protect the operator that are based on an estima-

tion of exposure in the actual conditions of use (tak-

ing account of all parts of the operating cycle such

as the times when the tool is switched o and when

it is running idle in addition to the trigger time).

Vibration

The vibration total value (tri-axial vector sum) deter-

mined according to EN60335-2-77:

Model LM001J

Vibration emission (ah) : 2.5 m/s2 or less

Uncertainty (K) : 1.5 m/s2

Model LM002J

Vibration emission (ah) : 2.5 m/s2 or less

Uncertainty (K) : 1.5 m/s2

NOTE: The declared vibration total value(s) has been

measured in accordance with a standard test method

and may be used for comparing one tool with another.

NOTE: The declared vibration total value(s) may also

be used in a preliminary assessment of exposure.

WARNING:

The vibration emission during actual

use of the power tool can dier from the declared val-

ue(s) depending on the ways in which the tool is used

especially what kind of workpiece is processed.

WARNING:

Be sure to identify safety measures

to protect the operator that are based on an estima-

tion of exposure in the actual conditions of use (tak-

ing account of all parts of the operating cycle such

as the times when the tool is switched o and when

it is running idle in addition to the trigger time).

EC Declaration of Conformity

For European countries only

The EC declaration of conformity is included as Annex A

to this instruction manual.

SAFETY WARNINGS

General power tool safety warnings

WARNING: Read all safety warnings, instruc-

tions, illustrations and specications provided

with this power tool. Failure to follow all instructions

listed below may result in electric shock, re and/or

serious injury.

Save all warnings and instruc-

tions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Cordless Lawn Mower Safety Warnings

1. Do not use the lawnmower in bad weather

conditions, especially when there is a risk of

lightning. This decreases the risk of being struck

by lightning.

2. Thoroughly inspect the area for wildlife where

the lawnmower is to be used. Wildlife may be

injured by the lawnmower during operation.

3. Thoroughly inspect the area where the lawn-

mower is to be used and remove all stones,

sticks, wires, bones, and other foreign objects.

Thrown objects can cause personal injury.

4. Before using the lawnmower, always visually

inspect to see that the blade and the blade

assembly are not worn or damaged. Worn or

damaged parts increase the risk of injury.

5. Check the grass catcher frequently for wear or

deterioration. A worn or damaged grass catcher

may increase the risk of personal injury.

6. Keep guards in place. Guards must be in work-

ing order and be properly mounted. A guard

that is loose, damaged, or is not functioning cor-

rectly may result in personal injury.

7. Keep all cooling air inlets clear of debris.

Blocked air inlets and debris may result in over-

heating or risk of re.

11 ENGLISH

8.

While operating the lawnmower, always wear non-slip and

protective footwear. Do not operate the lawnmower when

barefoot or wearing open sandals. This reduces the chance

of injury to the feet from contact with the moving blade.

9. While operating the lawnmower, always wear

long trousers. Exposed skin increases the likeli-

hood of injury from thrown objects.

10. Do not operate the lawnmower in wet grass.

Walk, never run. This reduces the risk of slipping

and falling which may result in personal injury.

11.

Do not operate the lawnmower on excessively

steep slopes. This reduces the risk of loss of control,

slipping and falling which may result in personal injury.

12. When working on slopes, always be sure of

your footing, always work across the face

of slopes, never up or down and exercise

extreme caution when changing direction. This

reduces the risk of loss of control, slipping and

falling which may result in personal injury.

13. Use extreme caution when reversing or pulling

the lawnmower towards you. Always be aware

of your surroundings. This reduces the risk of

tripping during operation.

14. Do not touch blades and other hazardous

moving parts while they are still in motion. This

reduces the risk of injury from moving parts.

15.

When clearing jammed material or cleaning the lawn-

mower, make sure all power switches are o and the

battery pack is disconnected. Unexpected operation of

the lawnmower may result in serious personal injury.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity

with product (gained from repeated use) replace strict

adherence to safety rules for the subject product.

MISUSE or failure to follow the safety rules stated in this

instruction manual may cause serious personal injury.

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

Read all safety warnings and all

instructions. Failure to follow the warnings and instruc-

tions may result in electric shock, re and/or serious injury.

Save all warnings and instruc-

tions for future reference.

Training

1.

Read the instructions carefully. Be familiar with

the controls and the proper use of the mower.

2. Never allow children or people unfamiliar with

these instructions to use the mower. Local

regulations can restrict the age of the operator.

3. Never operate the mower while people, espe-

cially children, or pets are nearby.

4. Keep in mind that the operator or user is

responsible for accidents or hazards occurring

to other people or their property.

5. Children should be supervised to ensure that

they do not play with the mower.

6. Physical condition - Do not operate mower

while under the inuence of drugs, alcohol, or

any medication.

Preparation

1. While operating the mower, always wear sub-

stantial footwear and long trousers. Do not

operate the mower when barefoot or wearing

open sandals. Avoid wearing clothing or jew-

elry that is loose tting or that has hanging

cords or ties. They can be caught in moving

parts.

2. Before use, always visually inspect the mower

for damaged, missing or misplaced guards or

shields.

3. Be sure the area is clear of other people before

mowing. Stop mower if anyone enters the area.

4. Do not insert the lock key into mower until it is

ready to be used.

5. Always wear protective goggles to protect

your eyes from injury when using power tools.

The goggles must comply with ANSI Z87.1 in

the USA, EN 166 in Europe, or AS/NZS 1336

in Australia/New Zealand. In Australia/New

Zealand, it is legally required to wear a face

shield to protect your face, too.

It is an employer's responsibility to enforce

the use of appropriate safety protective equip-

ments by the tool operators and by other per-

sons in the immediate working area.

6. Check the blades or blade bolts carefully for

cracks or damage before operation. Replace

cracked or damaged blades or blade bolts

immediately.

7. Remove foreign matters such as rocks, wire,

bottles, bones and large sticks from the work

area before mowing to prevent personal injury

or damage to the mower.

8. Objects struck by the mower blade can cause

severe injuries to persons. The lawn should

always be carefully examined and cleared of

all objects prior to each mowing.

9. Watch for holes, ruts, bumps, rocks, or other

hidden objects. Uneven terrain could cause a slip

and fall accident. Tall grass can hide obstacles.

10. Use personal protective equipment. Always

wear eye protection. Protective equipment such

as a dust mask, non-skid safety shoes, hard hat or

hearing protection used for appropriate conditions

will reduce personal injuries.

Operation

1. Do not overreach. Keep the balance at all

times. Always be sure of the footing on slopes.

Walk, never run.

12 ENGLISH

2. Stop the mower and remove the lock key, and

make sure that all moving parts have come to

a complete stop:

- whenever you leave the mower,

- before clearing blockages or unclogging chute,

- before checking, cleaning or working on the

mower,

- after striking a foreign object. Inspect the

mower for damage and make repairs before

restarting and operating the mower,

- whenever the mower starts vibrating

abnormally.

3. Never operate the mower with defective

guards or shields, or without safety devices,

for example deectors and/or grass basket, in

place.

4. Avoid using the mower in bad weather con-

ditions especially when there is a risk of

lightning.

5. Wear eye protection and stout shoes at all

times while operating the mower.

6. Operate the mower only in daylight or in good

articial light.

7. Switch on the mower carefully according to

instructions and with feet well away from the

blade(s).

8. Take care against injury to feet and hands from

the mower blades.

9. Always ensure that the ventilation openings

are kept clear of debris.

10. Mow across the face of slopes, never up and

down. Exercise extreme caution when chang-

ing direction on slopes. Do not mow exces-

sively steep slopes.

11. Use extreme caution when reversing or pulling

the mower towards you.

12. Stop the blade(s) if the mower has to be tilted

for transportation when crossing surfaces

other than grass, and when transporting the

mower to and from the area to be used.

13. Do not tilt the mower when switching on the

motor, except if the mower has to be tilted

for starting. In this case, do not tilt it more

than absolutely necessary and lift only the

part, which is away from the operator. Always

ensure that both hands are in the operating

position before returning the mower to the

ground.

14. Do not put hands or feet near or under rotating

parts. Keep clear of the discharge opening at

all times.

15. Do not transport the mower while the mower is

turned on.

16. Avoid operating the mower in wet grass.

17. Always keep a rm hold on the handle.

18. Don't grasp the exposed cutting blades or

cutting edges when picking up or holding the

mower.

19. Keep hands and feet away from rotating

blades. Caution - Blades coast after the mower

is switched o.

20. Stop operation immediately if you notice

anything unusual. Switch o the mower and

remove the lock key. Then inspect the mower.

21. Never attempt to make cutting height adjust-

ments while mower is running if the mower

has cutting height adjustment feature.

22. Release switch lever and wait for blade rota-

tion to stop before crossing driveways, walks,

roads, and any gravel-covered areas. Also

remove the lock key if you leave the mower,

reach to pick up or remove something out of

your way, or for any other reason that may

distract you from what you are doing.

23. If the mower strikes a foreign object, follow

these steps:

- Stop the mower, release the switch lever and

wait until the blade comes to a complete stop.

- Remove the lock key and the battery cartridge.

- Thoroughly inspect the mower for any

damage.

- Replace the blade if it is damaged in any way.

Repair any damage before restarting and con-

tinuing to operate the mower.

24. Do not start the mower when standing in front

of the discharge opening.

25. If the mower starts to vibrate abnormally

(check immediately)

- inspect for damage,

- replace or repair any damaged parts,

- check for and tighten any loose parts.

26. Never direct discharged material toward

anyone. Avoid discharging material against a

wall or obstruction. Material may ricochet back

toward the operator. Stop the blade when crossing

gravel surfaces.

27. Do not pull the mower backwards unless

absolutely necessary. When you are compelled

to back the mower from a fence or other similar

obstruction, look down and behind before and

while moving backwards.

28. Shut the motor o and wait until the blade

comes to a complete stop before removing the

grass catcher. Beware that the blades coast after

turn o.

29. When you use the machine on muddy ground,

wet slope, or slippery place, pay attention to

your footing.

30. Do not submerge the machine into a puddle.

31. When operating the machine, pay attention to

piping and wiring.

Maintenance and storage

1. Replace worn or damaged parts for safety.

Use only genuine replacement parts and

accessories.

2. Inspect and maintain the mower regularly.

3. When not in use, store the mower out of the

reach of children.

4. Keep all nuts, bolts, and screws tight to

be sure the equipment is in safe working

condition.

5. Check the grass basket frequently for wear or

deterioration. For storage, always make sure

the grass basket is empty. Replace a worn

grass basket with a new factory replacement

for safety.

6. Use only the manufacturer genuine blades

specied in this manual.

13 ENGLISH

7. Be careful during adjustment of the mower

to prevent entrapment of the ngers between

moving blades and xed parts of the mower.

8. Check the blade mounting bolt at frequent

intervals for proper tightness.

9.

Always allow the mower to cool down before storing.

10. When servicing the blades be aware that, even

though the power source is switched o, the

blades can still be moved.

11. Never remove or tamper with safety devices.

Check their proper operation regularly. Never

do anything to interfere with the intended

function of a safety device or to reduce the

protection provided by a safety device.

12. Do not leave the machine unattended outdoors

in the rain.

13. When storing the machine, avoid direct sun-

light and rain, and store it in a place where it

does not get hot or humid.

Battery tool use and care

1. Recharge only with the charger specied by

the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of re

when used with another battery pack.

2. Use power tools only with specically desig-

nated battery packs. Use of any other battery

packs may create a risk of injury and re.

3. When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another. Shorting the battery termi-

nals together may cause burns or a re.

4. Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If con-

tact accidentally occurs, ush with water. If

liquid contacts eyes, additionally seek medical

help. Liquid ejected from the battery may cause

irritation or burns.

5. Do not use a battery pack or tool that is dam-

aged or modied. Damaged or modied batteries

may exhibit unpredictable behaviour resulting in

re, explosion or risk of injury.

6. Do not expose a battery pack or tool to re or

excessive temperature. Exposure to re or tem-

perature above 130 °C may cause explosion.

7. Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range specied in the instruc-

tions. Charging improperly or at temperatures

outside the specied range may damage the

battery and increase the risk of re.

Electrical and battery safety

1. Do not dispose of the battery(ies) in a re.

The cell may explode. Check with local codes for

possible special disposal instructions.

2.

Do not open or mutilate the battery(ies). Released

electrolyte is corrosive and may cause damage to the

eyes or skin. It may be toxic if swallowed.

3.

Do not charge battery in rain, or in wet locations.

4. Do not charge the battery outdoors.

5. Do not handle charger, including charger plug,

and charger terminals with wet hands.

6. Do not replace the battery in the rain.

7. Do not wet the terminal of battery with liquid

such as water, or submerge the battery. Do not

leave the battery in the rain, nor charge, use,

or store the battery in a damp or wet place. If

the terminal gets wet or liquid enters inside of bat-

tery, the battery may be short circuited and there is

a risk of overheat, re, or explosion.

8. After removing the battery from the machine or

charger, be sure to attach the battery cover to

the battery and store it in a dry place.

9. Do not replace the battery with wet hands.

10. Avoid dangerous environment. Don't use the

machine in dump or wet locations or expose it

to rain. Water entering the machine will increase

the risk of electric shock.

11. If the battery cartridge gets wet, drain the

water inside and then wipe it with a dry cloth.

Dry the battery cartridge completely in a dry

place before use.

Service

1. Have your power tool serviced by a qualied

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

2. Never service damaged battery packs. Service

of battery packs should only be performed by the

manufacturer or authorized service providers.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product.

MISUSE or failure to follow the safety rules stated

in this instruction manual may cause serious

personal injury.

Important safety instructions for

battery cartridge

1.

Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using battery.

2. Do not disassemble or tamper the battery

cartridge. It may result in a re, excessive heat,

or explosion.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them

out with clear water and seek medical atten-

tion right away. It may result in loss of your

eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

ductive material.

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

14 ENGLISH

A battery short can cause a large current

ow, overheating, possible burns and even a

breakdown.

6. Do not store and use the tool and battery car-

tridge in locations where the temperature may

reach or exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a re.

8. Do not nail, cut, crush, throw, drop the battery

cartridge, or hit against a hard object to the

battery cartridge. Such conduct may result in a

re, excessive heat, or explosion.

9. Do not use a damaged battery.

10. The contained lithium-ion batteries are subject

to the Dangerous Goods Legislation require-

ments.

For commercial transports e.g. by third parties,

forwarding agents, special requirement on pack-

aging and labeling must be observed.

For preparation of the item being shipped, consult-

ing an expert for hazardous material is required.

Please also observe possibly more detailed

national regulations.

Tape or mask o open contacts and pack up the

battery in such a manner that it cannot move

around in the packaging.

11. When disposing the battery cartridge, remove

it from the tool and dispose of it in a safe

place. Follow your local regulations relating to

disposal of battery.

12. Use the batteries only with the products

specied by Makita. Installing the batteries to

non-compliant products may result in a re, exces-

sive heat, explosion, or leak of electrolyte.

13. If the tool is not used for a long period of time,

the battery must be removed from the tool.

14. During and after use, the battery cartridge may

take on heat which can cause burns or low

temperature burns. Pay attention to the han-

dling of hot battery cartridges.

15. Do not touch the terminal of the tool imme-

diately after use as it may get hot enough to

cause burns.

16. Do not allow chips, dust, or soil stuck into the

terminals, holes, and grooves of the battery

cartridge. It may cause heating, catching re,

burst and malfunction of the tool or battery car-

tridge, resulting in burns or personal injury.

17. Unless the tool supports the use near

high-voltage electrical power lines, do not use

the battery cartridge near a high-voltage elec-

trical power lines. It may result in a malfunction

or breakdown of the tool or battery cartridge.

18. Keep the battery away from children.

SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that

have been altered, may result in the battery bursting

causing res, personal injury and damage. It will

also void the Makita warranty for the Makita tool and

charger.

Tips for maintaining maximum

battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice

less tool power.

2. Never recharge a fully charged battery car-

tridge. Overcharging shortens the battery

service life.

3. Charge the battery cartridge with room tem-

perature at 10 °C - 40 °C (50 °F - 104 °F). Let

a hot battery cartridge cool down before

charging it.

4. When not using the battery cartridge, remove

it from the tool or the charger.

5. Charge the battery cartridge if you do not use

it for a long period (more than six months).

ASSEMBLY

WARNING: Always be sure that the lock key

and battery cartridge are removed before carrying

out any work on the mower. Failure to remove the

lock key and the battery cartridge may result in seri-

ous personal injury from accidental start-up.

WARNING: Never start the mower unless it is

completely assembled. Operation of the machine

in a partially assembled state may result in serious

personal injury from accidental start-up.

Installing the handle

NOTICE: When installing the handles, be careful

not to pinch the cord between the handles. If the

cord is damaged, the mower switch may not work.

1. Align the hole in the lower handle with the hole

in the upper handle, then insert the bolt from outside,

and then tighten the thumb nut from inside. Perform the

same procedure on the other side.

► Fig.1: 1. Lower handle 2. Thumb nut 3. Bolt

4. Upper handle

2. Turn the knob 90° while pulling the knob on the

lower handle to release the locking pin. Perform the

same procedure on the other side. Raise the handle,

and then turn the knob on both sides 90°. Make sure

that the knobs are securely xed.

► Fig.2: 1. Knob

NOTE: Supporting the handle makes it easier to

release the locking pin when pulling the knob.

Removing the mulching plug

1. Open the rear cover.

► Fig.3: 1. Rear cover

2. Lift up the mulching plug slightly, and then remove

it.

► Fig.4: 1. Mulching plug

15 ENGLISH

Assembling the grass basket

1. Pick up the upper clip of the grass basket.

► Fig.5: 1. Upper clip

2. Insert the frame into the grass basket as far as it

will go while holding the handle of the frame.

► Fig.6: 1. Handle

NOTICE: Do not insert the handle into the grass

basket. Be sure to insert the frame along the stitch of

the grass basket.

3. Make sure that there is no sagging on the corners

of the grass basket.

► Fig.7

4. Open the upper clip, and attach it to the frame.

► Fig.8

5. Attach all the other clips as shown in the gure.

Make sure that all the clips are securely attached to the

frame.

► Fig.9: 1. Clip

Installing or removing the grass

basket

To install the grass basket, follow the steps below.

1. Open the rear cover.

► Fig.10: 1. Rear cover

2. Hold the handle of the grass basket, and then

hook the grass basket on the rod of the mower body as

shown in the gure.

► Fig.11: 1. Grass basket 2. Handle 3. Rod

To remove the grass basket, open the rear cover, and

then remove the grass basket by holding the handle.

Attaching the mulching plug

1. Open the rear cover, and then remove the grass

basket.

► Fig.12: 1. Rear cover 2. Grass basket

2. Attach the mulching plug by pushing it as far as it

will go so that the protrusions on the mulching plug t

into the holes on the machine.

► Fig.13: 1. Mulching plug 2. Protrusion

FUNCTIONAL

DESCRIPTION

Installing or removing battery

cartridge

CAUTION: Always switch o the machine

before installing or removing of the battery

cartridge.

CAUTION: Hold the machine and the battery

cartridge rmly when installing or removing bat-

tery cartridge. Failure to hold the machine and the

battery cartridge rmly may cause them to slip o

your hands and result in damage to the machine and

battery cartridge and a personal injury.

CAUTION: Make sure that you lock the battery

cover before use. Otherwise, mud, dirt, or water may

cause damage to the product or the battery cartridge.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

not being inserted correctly.

CAUTION: Hold the battery cover rmly when

installing or removing the battery cartridge.

To install the battery cartridge;

1. Pull up the locking lever, and then open the battery

cover.

► Fig.14: 1. Battery cover 2. Locking lever

2. Hold the battery cartridge in the upright position

with the indicator lamps facing forward. Insert the bat-

tery cartridge into the machine until it is latched with the

battery lock lever.

► Fig.15: 1. Indicator lamps 2. Battery lock lever

NOTE: Pushing the battery vertically from above

makes the machine harder to move and makes it

easier to install the battery.

► Fig.16

3. Insert the lock key in the place shown in the gure

as far as it will go.

► Fig.17: 1. Lock key

4. Close the battery cover and push it until it is

latched with the locking lever.

To remove the battery cartridge;

1. Pull up the locking lever and open the battery

cover.

2. Push the battery lock lever, and then pull out the

battery cartridge from the machine.

► Fig.18: 1. Battery lock lever 2. Battery cartridge

3. Lock key

3. Pull out the lock key.

4. Close the battery cover.

16 ENGLISH

Machine / battery protection system

The machine is equipped with a machine/battery

protection system. This system automatically cuts o

power to the motor to extend machine and battery life.

The machine will automatically stop during operation if

the machine or battery is placed under one of the fol-

lowing conditions:

Overload protection

When the machine or battery is operated in a manner

that causes it to draw an abnormally high current,

the machine automatically stops and the main power

lamp blinks in green. In this situation, turn the machine

o and stop the application that caused the machine

to become overloaded. Then turn the machine on to

restart.

Overheat protection

If the machine or battery cartridge is overheated, the

machine stops automatically. When the machine is

overheated, the main power lamp lights up in red. When

the battery cartridge is overheated, the main power

lamp blinks in red. Let the machine and/or battery cool

down before turning the machine on again.

Overdischarge protection

When the battery capacity is not enough, the machine

stops automatically and the main power lamp blinks in

red.

In this case, remove the battery from the machine and

charge the battery cartridge or change the battery car-

tridge to fully charged one.

Protections against other causes

Protection system is also designed for other causes that

could damage the machine and allows the machine to

stop automatically. Take all the following steps to clear

the causes, when the machine has been brought to a

temporary halt or stop in operation.

1. Turn the machine o, and then turn it on again to

restart.

2. Charge the battery(ies) or replace it/them with

recharged battery(ies).

3. Let the machine and battery(ies) cool down.

If no improvement can be found by restoring protection

system, then contact your local Makita Service Center.

Indicating the remaining battery

capacity

Press the check button on the battery cartridge to indi-

cate the remaining battery capacity. The indicator lamps

light up for a few seconds.

► Fig.19: 1. Indicator lamps 2. Check button

Indicator lamps Remaining

capacity

Lighted O Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

The battery

may have

malfunctioned.

NOTE:

Depending on the conditions of use and the ambient tem-

perature, the indication may dier slightly from the actual capacity.

NOTE: The rst (far left) indicator lamp will blink when

the battery protection system works.

Control panel

The control panel has the main power switch and the

mode switching button.

► Fig.20: 1. Soft no-load mode lamp 2. Noise reduc-

tion mode lamp 3. Mode switching button

4. Main power lamp 5. Main power switch

Main power switch

WARNING: Always turn o the main power

switch when not in use.

To turn on the machine, press the main power switch.

The main power lamp lights up in green. To turn o the

machine, press the main power switch again.

NOTE: If the main power lamp lights up in red or

blinks in red or green, refer to the instructions for

machine/battery protection system.

NOTE:

This machine employs the auto power-o func-

tion. To avoid unintentional start up, the main power

switch will automatically shut down when the switch

lever and drive lever (if equipped) are not pulled for a

certain period after the main power switch is turned on.

Mode switching button

You can switch the operating mode by pressing the

mode switching button. When the machine is turned on,

the machine starts up in the normal mode.

When you press the mode switching button, the machine shifts to

the soft no-load mode and the soft no-load mode lamp lights up in

green. In the soft no-load mode, you can minimizes start-up shock.

When you press the mode switching button again, the

machine shifts to the noise reduction mode and the noise

reduction mode lamp lights up in green. In the noise

reduction mode, you can decrease the noise at mowing.

When you press the mode switching button again, the

machine returns to the normal mode.

17 ENGLISH

Switch action

WARNING: Before installing the battery car-

tridge, always check to see that the switch lever

actuates properly and returns to the original posi-

tion when released. Operating the machine with a

switch that does not actuate properly can lead to loss

of control and serious personal injury.

NOTE: The mower does not start without pressing the

switch button even the switch lever is pulled.

NOTE: Mower may not start due to the overload

when you try to mow long or dense grass at a time.

Increase the mowing height in this case.

This mower is equipped with the lock key and handle switch.

If you notice anything unusual with either of the lock key

or switch, stop the operation immediately and have them

checked by your nearest Makita Authorized Service Center.

1. Install the battery cartridge. Insert the lock key,

and then close the battery cover.

2. Press the main power switch.

3. Pull the switch lever toward you while holding

down the switch button. Release the switch button as

soon as the motor starts running.

► Fig.21: 1. Switch button 2. Switch lever

NOTE: If the lock key is not inserted, the power lamp

blinks in green when you pull the switch lever.

4. Release the switch lever to stop the motor.

Adjusting the mowing height

WARNING: Never put your hand or leg under

the mower body when adjusting the mowing

height.

WARNING: Always make sure that the lever

ts in the groove properly before operation.

The mowing height can be adjusted in the range of

between 20 mm and 100 mm.

Remove the lock key, and then pull the mowing height

adjusting lever outward of the mower body and move it

to your desired mowing height.

► Fig.22: 1. Mowing height adjusting lever

The table below shows the relationship between the

number on the mower body and the approximate mow-

ing height.

Number Mowing height

120 mm

226 mm

332 mm

440 mm

549 mm

659 mm

770 mm

881 mm

992 mm

10 100 mm

Hold the lower handle with one hand, and then move

the mowing height adjusting lever with the other hand.

► Fig.23: 1. Mowing height adjusting lever 2. Lower

handle

NOTE: The mowing height gures should be used

just as a guideline. Depending on the conditions of

the lawn or the ground, the actual lawn height may

become slightly dierent from the set height.

NOTE: Try a test mowing of grass in a less conspicu-

ous place to get your desired height.

Grass level indicator

Grass level indicator shows the volume of mowed

grass. When the grass basket is not full, the indicator

oats while the blades are running.

► Fig.24: 1. Grass level indicator

When the grass basket is almost full, the indicator does

not oat while the blades are running. In this case, stop

the operation immediately and empty the basket.

► Fig.25: 1. Grass level indicator

NOTE: This indicator is a rough guide. Depending on

the conditions of inside of the basket, this indicator

may not work properly.

Adjusting the handle height

The handle height can be adjusted in two levels.

1. Hold the lower handle, and then turn the knob 90°

while pulling the knob on the lower handle to release

the locking pin. Perform the same procedure on the

other side.

► Fig.26: 1. Lower handle 2. Knob

NOTE: Supporting the handle makes it easier to

release the locking pin when pulling the knob.

2. Adjust the handle height, and then turn the

knob on both sides 90°. Make sure that the knobs are

securely xed.

► Fig.27: 1. Knob

Using mulching plug

The mulching plug allows you to return the cut grass to

the ground without gathering the cut grass in the grass

basket. When you operate the machine with the mulch-

ing plug, be sure to remove the grass basket.

NOTICE: When using the machine with the

mulching plug, make sure that the total length of

grass after cutting is 30 mm or more, and the cut

length is 15 mm or less.

► Fig.28: (1) 30 mm or more (2) 15 mm or less

Using the rear discharge

Using the rear discharge allows you to discharge the cut

grass to the ground from the rear side of the machine

without gathering the cut grass in the grass basket.

When you operate the machine using the rear dis-

charge, be sure to remove the grass basket and mulch-

ing plug, and close the rear cover.

18 ENGLISH

Electronic function

The machine is equipped with the electronic functions

for easy operation.

• Constant speed control of blade rotation

Electronic speed control for obtaining constant

speed. Possible to get ne nish, because the

rotating speed is kept constant even under load

condition.

• Electric brake

This machine is equipped with an electric brake.

If the machine consistently fails to quickly stop

the mower blades after releasing the switch lever,

have the machine serviced at Makita Authorized

Service Center.

OPERATION

Mowing

WARNING: Before mowing, clear away sticks

and stones from mowing area. Furthermore, clear

away any weeds from mowing area in advance.

WARNING: Always wear the safety goggles or

safety glasses with side shields when operating

the mower.

CAUTION: If the cut grass or foreign object

blocks up inside of the mower body, be sure to

remove the lock key and battery cartridge and

wear gloves before removing the grass or foreign

object.

NOTICE: Use this machine for mowing lawn only.

Do not mow weeds with this machine.

► Fig.29

Firmly hold the handle with both hands when mowing.

The mowing speed guideline is approximately 7 to 14

meters per 10 seconds.

► Fig.30

The center lines of the front wheels are guidelines to

mowing width. Using the center lines as guidelines,

mow in strips. Overlap by one half to one third the previ-

ous strip to mow the lawn evenly.

► Fig.31: 1. Mowing width 2. Overlapping area

3. Center line

Change the mowing direction each time to prevent the

grass grain pattern from forming in just one direction.

► Fig.32

Periodically check the grass basket for mowed grass.

Empty the grass before it becomes full. Before every

periodical check, be sure to stop the mower then

remove the lock key and the battery cartridge.

NOTICE: Using the mower with the grass basket

full prevents smooth blade rotation and places

an extra load on the motor, which may cause

breakdown.

Mowing a long-grass lawn

Do not try to cut long grass all at once. Instead, mow

the lawn in steps. Leave a day or two between mowings

until the lawn becomes evenly short.

► Fig.33

NOTE: Mowing long grass to a short length all at

once may cause the grass to die. The cut grass may

also block up inside of the mower body.

NOTE: If the unevenness in the length of lawn or poor

nish is found after mowing, or decrease of the motor

speed is found during mowing, decrease the mowing

speed, or raise the mowing height.

Emptying the grass basket

WARNING: To reduce a risk of accident, reg-

ularly check the grass basket for any damage or

weakened strength. Replace the grass basket if

necessary.

1. Release the switch lever.

2. Remove the lock key.

3. Open the rear cover and take out the grass basket

by holding the handle.

► Fig.34: 1. Rear cover 2. Handle 3. Grass basket

4. Empty the grass basket.

MAINTENANCE

WARNING: Always be sure that the lock

key and battery cartridge are removed from the

mower before storing or carrying the mower or

attempting to perform inspection or maintenance.

WARNING: Always remove the lock key when

the mower is not in use. Store the lock key in a

safe place out of reach of children.

WARNING: Wear gloves when performing

inspection or maintenance.

WARNING: Always wear the safety goggles or

safety glasses with side shields when performing

inspection or maintenance.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

To maintain product SAFETY and RELIABILITY,

repairs, any other maintenance or adjustment should

be performed by Makita Authorized or Factory Service

Centers, always using Makita replacement parts.

Maintenance

1. Remove the lock key and battery cartridge, and

then close the battery cover.

2. Put the mower on its side. Clean grass clippings

accumulated on the underside of mower deck.

19 ENGLISH

3. Pour water toward the bottom of the machine to

which the blade is attached.

NOTICE: Do not wash the machine with high

pressure water.

4. Check all nuts, bolts, screws, etc. for tightness.

5. Inspect moving parts for damage, breakage, and

wear. Damaged or missing parts should be repaired or

replaced.

6. Store the mower in a safe place out of the reach of

children.

Carrying the mower

CAUTION: Before carrying the mower, make

sure that the battery cartridge and lock key are

removed.

When carrying the mower, hold the rear grip and the

lower holding part at the front of the machine with two

people as shown in the gure.

► Fig.35: 1. Lower holding part 2. Rear grip

Storing

CAUTION: When putting the machine in the

upright position, place the machine on a at and

stable surface. If the machine is placed on an unsta-

ble surface, the machine may fall over and cause an

injury.

Store mower indoors in a cool, dry and locked place.

Don't store the mower and charger in locations where

the temperature may reach or exceed 40 °C.

1. Remove the battery cartridge and lock key.

2. Turn the knob 90° while pulling the knob on the

lower handle to release the locking pin. Perform the

same procedure on the other side, and then fold the

handle.

► Fig.36: 1. Knob

NOTE: Supporting the handle makes it easier to

release the locking pin when pulling the knob.

3. Turn the knob on both sides 90°. Make sure that

the knobs are securely xed.

► Fig.37: 1. Knob

NOTICE: Be careful not to pinch the cord when

folding the handle.

4. Loosen the thumb nuts on both sides, and then

fold the upper handle as shown in the gure.

► Fig.38: 1. Thumb nut 2. Upper handle

5. Place the machine in the upright position.

NOTE: When putting the mower in the upright posi-

tion, do not hold the handle only, but hold the mower

body and handle.

6. Store the grass basket as shown in the gure.

► Fig.39: 1. Grass basket

► Fig.40: 1. Grass basket

Removing or installing the mower

blade

WARNING: The blade coasts for a few sec-

onds after releasing the switch. Do not start any

operation until the blade comes to a complete

stop.

WARNING: Always remove the lock key and

battery cartridge when removing or installing the

blade. Failure to remove the lock key and battery

cartridge may cause a serious injury.

WARNING: Always wear gloves when han-

dling the blade.

Removing the mower blade

1. Put the mower on its side so that the mowing

height adjusting lever comes to the lower side.

2. To lock the blade, insert the pin into the hole on

the mower body as far as it will go.

3. Turn the bolt counterclockwise with box wrench

17.

► Fig.41: 1. Mower blade 2. Pin 3. Box wrench

4. Remove the bolt, and then mower blade.

► Fig.42: 1. Blade support 2. Mower blade 3. Bolt

4. Protrusion

NOTICE: When installing the mower blade, make

sure that the protrusions on the blade support t

in the holes in the mower blade.

Installing the mower blade

WARNING: Install the mower blade carefully.

It has a top/bottom facing.

WARNING: Tighten the bolt clockwise rmly

to secure the blade.

WARNING: Make sure that the mower blade

and all the xing parts are installed correctly and

tightened securely.

WARNING: When you replace the blades,

always follow the instructions provided in this

manual.

NOTICE: After installing the mower blades,

remove the pin from the mower body.

To install the mower blades, perform the removal proce-

dure in reverse.

20 ENGLISH

TROUBLESHOOTING

Before asking for repairs, conduct your own inspection rst. If you nd a problem that is not explained in the manual,

do not attempt to disassemble the machine. Instead, ask Makita Authorized Service Centers, always using Makita

replacement parts for repairs.

State of abnormality Probable cause (malfunction) Remedy

Mower does not start. Battery cartridge is not installed. Install charged battery cartridge.

Battery problem (under voltage) Recharge the battery cartridge. If recharging is not

eective, replace battery cartridge.

The lock key is not inserted. Insert the lock key.

Motor stops running after a little use. Battery's charge level is low. Recharge the battery cartridge. If recharging is not

eective, replace battery cartridge.

Cutting height is too low. Increase the cutting height.

Cut grass is clogged in the mower. Remove the clogged grass from the mower.

Motor does not reach maximum

RPM. Battery cartridge is installed improperly. Install the battery cartridge as described in this

manual.

Battery power is dropping. Recharge the battery cartridge. If recharging is not

eective, replace battery cartridge.

The drive system does not work

correctly. Ask your local authorized service center for repair.

Mower blade does not rotate:

stop the mower immediately!

Foreign object such as a branch is

jammed near the blade. Remove the foreign object.

The drive system does not work

correctly. Ask your local authorized service center for repair.

Abnormal vibration:

stop the mower immediately!

Blade is imbalanced, excessively or

unevenly worn.

Replace the blade.

OPTIONAL

ACCESSORIES

CAUTION: These accessories or attachments

are recommended for use with your Makita

machine specied in this manual. The use of any

other accessories or attachments might present a risk

of injury to persons. Only use accessory or attach-

ment for its stated purpose.

If you need any assistance for more details regard-

ing these accessories, ask your local Makita Service

Center.

• Mower blade

• Makita genuine battery and charger

NOTE: Some items in the list may be included in the

product package as standard accessories. They may

dier from country to country.

Pagina se încarcă ...

Makita LM001J Manual de utilizare

Makita LM001J Manual de utilizare

în alte limbi

Lucrări conexe

Alte documente