Yamaha HTR-5990 Manualul proprietarului

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Printed in Malaysia V958320-2

OWNER’S MANUAL

IMPORTANT

Please record the serial number of this unit in the

space below.

MODEL:

Serial No.:

The serial number is located on the rear of the unit.

Retain this Owner’s Manual in a safe place for future

reference.

U

AV Receiver

HTR-5590

I CAUTION

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to alert

you to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may

be of sufficient magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert you to the presence of

important operating and maintenance (servicing)

instructions in the literature accompanying the

appliance.

1 Read Instructions – All the safety and operating instructions

should be read before the product is operated.

2 Retain Instructions – The safety and operating instructions

should be retained for future reference.

3 Heed Warnings – All warnings on the product and in the

operating instructions should be adhered to.

4 Follow Instructions – All operating and use instructions

should be followed.

5 Cleaning – Unplug this product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol cleaners.

Use a damp cloth for cleaning.

6 Attachments – Do not use attachments not recommended

by the product manufacturer as they may cause hazards.

7 Water and Moisture – Do not use this product near water –

for example, near a bath tub, wash bowl, kitchen sink, or

laundry tub; in a wet basement; or near a swimming pool;

and the like.

8 Accessories – Do not place this product on an unstable cart,

stand, tripod, bracket, or table. The product may fall,

causing serious injury to a child or adult, and serious

damage to the product. Use only with a cart, stand, tripod,

bracket, or table recommended by the manufacturer, or sold

with the product. Any mounting of the product should

follow the manufacturer’s instructions, and should use a

mounting accessory recommended by the manufacturer.

9 A product and cart combination should be

moved with care. Quick stops, excessive

force, and uneven surfaces may cause the

product and cart combination to overturn.

10 Ventilation – Slots and openings in the cabinet are provided

for ventilation and to ensure reliable operation of the

product and to protect it from overheating, and these

openings must not be blocked or covered. The openings

should never be blocked by placing the product on a bed,

sofa, rug, or other similar surface. This product should not

be placed in a built-in installation such as a bookcase or

rack unless proper ventilation is provided or the

manufacturer’s instructions have been adhered to.

11 Power Sources – This product should be operated only from

the type of power source indicated on the marking label. If

you are not sure of the type of power supply to your home,

consult your product dealer or local power company. For

products intended to operate from battery power, or other

sources, refer to the operating instructions.

12 Grounding or Polarization – This product may be equipped

with a polarized alternating current line plug (a plug having

one blade wider than the other). This plug will fit into the

power outlet only one way. This is a safety feature. If you

are unable to insert the plug fully into the outlet, try

reversing the plug. If the plug should still fail to fit, contact

your electrician to replace your obsolete outlet. Do not

defeat the safety purpose of the polarized plug.

13 Power-Cord Protection – Power-supply cords should be

routed so that they are not likely to be walked on or pinched

by items placed upon or against them, paying particular

attention to cords at plugs, convenience receptacles, and the

point where they exit from the product.

14 Lightning – For added protection for this product during a

lightning storm, or when it is left unattended and unused for

long periods of time, unplug it from the wall outlet and

disconnect the antenna or cable system. This will prevent

damage to the product due to lightning and power-line

surges.

15 Power Lines – An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into such

power lines or circuits. When installing an outside antenna

system, extreme care should be taken to keep from touching

such power lines or circuits as contact with them might be

fatal.

16 Overloading – Do not overload wall outlets, extension

cords, or integral convenience receptacles as this can result

in a risk of fire or electric shock.

17 Object and Liquid Entry – Never push objects of any kind

into this product through openings as they may touch

dangerous voltage points or short-out parts that could result

in a fire or electric shock. Never spill liquid of any kind on

the product.

18 Servicing – Do not attempt to service this product yourself

as opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all servicing to

qualified service personnel.

19 Damage Requiring Service – Unplug this product from the

wall outlet and refer servicing to qualified service personnel

under the following conditions:

a) When the power-supply cord or plug is damaged,

b) If liquid has been spilled, or objects have fallen into

the product,

c) If the product has been exposed to rain or water,

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

SAFETY INSTRUCTIONSIMPORTANT SAFETY INSTRUCTIONS

CAUTION II

1. IMPORTANT NOTICE : DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved

by Yamaha may void your authority, granted by the

FCC, to use the product.

2. IMPORTANT : When connecting this product to

accessories and/or another product use only high

quality shielded cables. Cable/s supplied with this

product MUST be used. Follow all installation

instructions. Failure to follow instructions could void

your FCC authorization to use this product in the USA.

3. NOTE : This product has been tested and found to

comply with the requirements listed in FCC

Regulations, Part 15 for Class “B” digital devices.

Compliance with these requirements provides a

reasonable level of assurance that your use of this

product in a residential environment will not result in

harmful interference with other electronic devices.

This equipment generates/uses radio frequencies and,

if not installed and used according to the instructions

found in the users manual, may cause interference

harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee

that interference will not occur in all installations. If

this product is found to be the source of interference,

which can be determined by turning the unit “OFF” and

“ON”, please try to eliminate the problem by using one

of the following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient

the antenna. If the antenna lead-in is 300 ohm ribbon

lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to

distribute this type of product. If you can not locate the

appropriate retailer, please contact Yamaha Electronics

Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA

90620.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

EXAMPLE OF ANTENNA GROUNDING

MAST

GROUND

CLAMP

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810–20)

GROUNDING CONDUCTORS

(NEC SECTION 810–21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250. PART H)

ELECTRIC

SERVICE

EQUIPMENT

NEC

– NATIONAL ELECTRICAL CODE

FCC INFORMATION (for US customers)

Note to CATV system installer:

This reminder is provided to call the CATV system

installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in particular,

specifies that the cable ground shall be connected to the

grounding system of the building, as close to the point of

cable entry as practical.

d) If the product does not operate normally by following

the operating instructions. Adjust only those controls

that are covered by the operating instructions as an

improper adjustment of other controls may result in

damage and will often require extensive work by a

qualified technician to restore the product to its normal

operation,

e) If the product has been dropped or damaged in any

way, and

f) When the product exhibits a distinct change in

performance - this indicates a need for service.

20 Replacement Parts – When replacement parts are

required, be sure the service technician has used

replacement parts specified by the manufacturer or have

the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric

shock, or other hazards.

21 Safety Check – Upon completion of any service or

repairs to this product, ask the service technician to

perform safety checks to determine that the product is in

proper operating condition.

22 Wall or Ceiling Mounting – The unit should be mounted

to a wall or ceiling only as recommended by the

manufacturer.

23 Heat – The product should be situated away from heat

sources such as radiators, heat registers, stoves, or other

products (including amplifiers) that produce heat.

24 Outdoor Antenna Grounding – If an outside antenna or

cable system is connected to the product, be sure the

antenna or cable system is grounded so as to provide some

protection against voltage surges and built-up static charges.

Article 810 of the National Electrical Code, ANSI/NFPA

70, provides information with regard to proper grounding of

the mast and supporting structure, grounding of the lead-in

wire to an antenna discharge unit, size of grounding

conductors, location of antenna discharge unit, connection

to grounding electrodes, and requirements for the

grounding electrode.

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean

place — away from direct sunlight, heat sources, vibration,

dust, moisture, and/or cold. Allow ventilation space of at

least 30 cm on the top, 20 cm on the left and right, and

20 cm on the back of this unit.

3 Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in a environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign object may fall onto

this unit and/or this unit may be exposed to liquid dripping

or splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to

this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections

are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cord from the wall outlet,

grasp the plug; do not pull the cord.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and

may cause fire, damage to this unit, and/or personal injury.

YAMAHA will not be held responsible for any damage

resulting from use of this unit with a voltage other than

specified.

13 To prevent damage by lightning, disconnect the power cord

from the wall outlet during an electrical storm.

14 Do not attempt to modify or fix this unit. Contact qualified

YAMAHA service personnel when any service is needed.

The cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the wall

outlet.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

16 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit is

faulty.

17 Before moving this unit, press STANDBY/ON to set this

unit in the standby mode, and disconnect the AC power plug

from the wall outlet.

18 VOLTAGE SELECTOR (For China model only)

The VOLTAGE SELECTOR on the rear panel of this unit

must be set for your local main voltage BEFORE plugging

into the AC main supply.

Voltages are 220/240 V AC, 50 Hz.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

This unit is not disconnected from the AC power source as

long as it is connected to the wall outlet, even if this unit

itself is turned off. This state is called the standby mode. In

this state, this unit is designed to consume a very small

quantity of power.

FOR CANADIAN CUSTOMERS

To prevent electric shock, match wide blade of plug to

wide slot and fully insert.

This Class B digital apparatus complies with Canadian

ICES-003.

III CAUTION

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s Consumer

Electronics Group want you to get the most out of your equipment

by playing it at a safe level. One that lets the sound come through

loud and clear without annoying blaring or distortion – and, most

importantly, without affecting your sensitive hearing.

Since hearing damage from loud sounds is often

undetectable until it is too late, YAMAHA and the

Electronic Industries Association’s Consumer

Electronics Group recommend you to avoid

prolonged exposure from excessive volume levels.

1

English

INTRODUCTION

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

CONTENTS

INTRODUCTION

CONTENTS ............................................................ 1

FEATURES ............................................................. 2

GETTING STARTED ............................................ 3

Checking the Package Contents ................................ 3

Installing Batteries in the Remote Control ................ 3

CONTROLS AND FUNCTIONS ......................... 4

Front Panel ................................................................ 4

Remote Control ......................................................... 6

Using the Remote Control ......................................... 7

Front Panel Display ................................................... 8

Rear Panel ................................................................. 9

PREPARATION

SPEAKER SETUP ............................................... 10

Speakers to Be Used ................................................ 10

Speaker Placement .................................................. 10

Connecting the Speakers ......................................... 11

CONNECTIONS .................................................. 14

Before Connecting Components ............................. 14

Connecting Video Components ............................... 14

Connecting Audio Components .............................. 17

Connecting the Antennas ......................................... 19

Connecting to a Subwoofer ..................................... 20

Connecting to the 6CH INPUT Jacks ..................... 20

Connecting the Power Supply Cords ....................... 21

Turning on the Power .............................................. 22

ON-SCREEN DISPLAY (OSD) .......................... 23

OSD Modes ............................................................. 23

Selecting the OSD Mode ......................................... 23

SPEAKER MODE SETTINGS .......................... 24

Summary of SPEAKER SET Items 1A through 1G ...

24

ADJUSTING THE SPEAKER OUTPUT

LEVELS ............................................................ 25

Before You Begin .................................................... 25

Using the Test Tone (TEST DOLBY SUR.) ........... 25

BASIC OPERATION

BASIC PLAYBACK ............................................. 27

Input Modes and Indications ................................... 29

Selecting a Sound Field Program ............................ 30

Selecting PRO LOGIC, PRO LOGIC or Neo: 6

... 31

DIGITAL SOUND FIELD PROCESSING

(DSP) ................................................................. 34

Understanding Sound Fields ................................... 34

Hi-Fi DSP Programs................................................ 34

CINEMA-DSP ........................................................ 34

Straight Decode ....................................................... 35

Sound Field Effect ................................................... 35

Features of DSP Programs ...................................... 36

Table of Program Names for Each Input Format .... 38

TUNING ................................................................ 39

Automatic and Manual Tuning ................................ 39

Presetting Stations ................................................... 40

Tuning in to a Preset Station ................................... 42

Exchanging Preset Stations ..................................... 42

BASIC RECORDING .......................................... 43

ADVANCED OPERATION

REMOTE CONTROL FEATURES ................... 44

Control Area ............................................................ 44

Setting the Manufacturer Code ............................... 45

Learn Feature ........................................................... 47

Changing the Source Name in the Display

Window ............................................................... 48

Clearing Learned Functions, Renamed Source

Names, and Setup Manufacturer Codes .............. 49

Each Component Control Area ............................... 50

SET MENU ........................................................... 55

Adjusting the Items on the SET MENU.................. 55

1 SPEAKER SET (speaker mode settings) ............ 56

2 LOW FRQ TEST ................................................ 59

3 L/R BALANCE (balance of the left and right

main speakers)..................................................... 60

4 HP TONE CTRL (headphone tone control) ........ 60

5 CENTER GEQ (center graphic equalizer) .......... 60

6 INPUT RENAME ............................................... 61

7 I/O ASSIGNMENT ............................................. 61

8 INPUT MODE (initial input mode) .................... 62

9 PARAM. INI (parameter initialization) .............. 63

10LFE LEVEL ........................................................ 63

11D-RANGE (dynamic range) ............................... 63

12SP DELAY .......................................................... 64

13DISPLAY SET .................................................... 65

14MEMORY GUARD ............................................ 65

156CH INPUT SET ................................................ 65

ADJUSTING THE LEVEL OF THE EFFECT

SPEAKERS ....................................................... 66

SLEEP TIMER ..................................................... 67

Setting the Sleep Timer ........................................... 67

Canceling the Sleep Timer ...................................... 67

ZONE 2 (For U.S.A., Canada and Australia

models) .............................................................. 68

Remote Control in Zone 2 ....................................... 69

ADDITIONAL INFORMATION

SOUND FIELD PROGRAM PARAMETER

EDITING .......................................................... 70

What is a Sound Field? ............................................ 70

Sound Field Program Parameters ............................ 70

Changing Parameter Settings .................................. 71

Resetting a Parameter to the Factory-set Value ....... 71

DIGITAL SOUND FIELD PARAMETER

DESCRIPTIONS .............................................. 72

TROUBLESHOOTING ....................................... 76

GLOSSARY .......................................................... 81

SPECIFICATIONS .............................................. 83

2

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are trademarks

of Dolby Laboratories.

“DTS”, “DTS-ES Extended Surround” and “Neo: 6” are

trademarks of Digital Theater System, Inc.

FEATURES

Built-in 6-Channel Power Amplifier

◆ Minimum RMS Output Power

(0.04% THD, 20 Hz – 20 kHz, 8Ω)

Main: 100 W + 100 W

Center: 100 W

Rear: 100 W + 100 W

Rear center: 100 W

Multi-Mode Digital Sound Field

Processing

◆ Dolby Pro Logic/Dolby Pro Logic Decoder

◆ Dolby Digital/Dolby Digital EX Decoder

◆ DTS/DTS ES Matrix 6.1, Discrete 6.1, DTS

Neo: 6 Decoder

◆ CINEMA DSP: Combination of YAMAHA DSP

Technology and Dolby Pro Logic, Dolby Digital

or DTS

◆ Virtual CINEMA DSP

◆ SILENT CINEMA DSP

Sophisticated AM/FM Tuner

◆ 40-Station Random Access Preset Tuning

◆ Automatic Preset Tuning

◆ Preset Station Shifting Capability (Preset

Editing)

Other Features

◆ 192-kHz/24-bit D/A Converter

◆ “SET MENU” which Provides You with 15 Items

for Optimizing This Unit for Your Audio/Video

System

◆ Test Tone Generator for Easier Speaker Balance

Adjustment

◆ 6-Channel External Decoder Input for Other

Future Formats

◆ BASS EXTENSION Button for Reinforcing

Bass Response

◆ On Screen Display Function Helpful in

Controlling This Unit

◆ S Video Signal Input/Output Capability

◆ Component Video Input/Output Capability

◆ Video Conversion (S Video → Composite Video)

◆ Optical and Coaxial Digital Audio Signal Jacks

◆ Sleep Timer

◆ Remote Control with Preset Manufacturer Codes

and “Learning” Capability

◆ PROCESSOR DIRECT for no alteration of the

original signal

◆ Custom Installation Facility (U.S.A., Canada and

Australia models only)

• y indicates a tip for your operation.

• Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button

names differ between the main unit and the remote control, the button name on the remote control is given in parentheses in this

manual.

• This manual is printed prior to production. Design and specifications are subject to change in part for the purpose of the improvement

in operativity and others. In this case the product has priority.

3

English

INTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

1

3

2

PHONO

POWER SLEEP

CLEAR

LEARN

STANDBY

TRANSMIT

RE–NAME

6CH INPUT

SYSTEM

V

-

AUX

A

D

-

TV/LD

POWER

REC

DISC SKIP

SET MENU

TV INPUT

A/B/C/D/E

AUDIO

VOL

LEVEL

MENU

STEREO

HALL

ENTER-

TAINMENT

MUSIC

VIDEO

TV

THEATER

SELECT

EX/ES

0

+

10

MOVIE

THEATER 1

MOVIE

THEATER 2

/DTS

SUR.

TEST

ON SCREEN

EFFECT

CHP/INDEX

TV VOL

RETURN

DISPLAY

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHURCH

CHCH

JAZZ CLUB

ROCK

CONCERT

TITLE

MUTE

POWER

AMP

AVTV

VCR2/DVRVCR 1 DVD

SELECT

CBL/SAT MD/TAPE CD-R

TUNER CD

+

–

3421

5

910

11 12

67 8

1 Press the part and slide the battery

compartment cover off.

2 Insert four supplied batteries (AAA, R03, UM-

4) according to the polarity markings on the

inside of the battery compartment.

3 Slide the cover back until it snaps into place.

■ Notes on batteries

• Change the batteries periodically.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline

and manganese batteries) together. Read the packaging

carefully as these different types of batteries may have

the same shape and color.

■ Changing batteries

As the batteries lose power, the operating range of the

remote control decreases and the indicator does not flash

or its light becomes dim. When you notice any of these

conditions, change all of the batteries.

Notes

• If the batteries have leaked, dispose of them immediately.

Avoid touching the leaked material or letting it come into

contact with clothing, etc. Clean the battery compartment

thoroughly before installing new batteries.

• If the remote control is without batteries for more than

2 minutes, or if exhausted batteries remain in the remote

control, the contents of the memory may be cleared. When the

memory is cleared, insert new batteries, set up the

manufacturer code and program any acquired functions that

may have been cleared.

AM loop antenna

(For Australia model)

Indoor FM antenna

(For U.S.A., Canada and

China models)

Batteries (4)

(AAA, R03, UM-4)

Remote control

GETTING STARTED

Checking the Package Contents

Check your package to make sure it has the following items.

Installing Batteries in the Remote Control

4

BASS

VOLUME

VIDEO AUXSILENT

PROGRAM

STEREO

SPEAKERS

6CH INPUT MODE

BASS

EXTENSION

PROCESSOR

DIRECT

PRESET

/

TUNING

PHONES

EFFECT

A/B/C/D/E

S VIDEO

MEMORY

FM/AM

EDIT

PRESET

/TUNING

MAN'L/AUTO FM AUTO/MAN'L MONO

TUNING

MODE

VIDEO AUDIO OPTICALLR

TUNER

STANDBY

/

ON

NATURAL SOUND AV RECEIVER

DSP

TREBLE

–

+

–

+

AB

DIGITAL

PRESET

/TUNING

EDIT

MEMORY

MAN'L/AUTO FM

TUNING

MODE

AUTO/MAN'L MONO

FM/AM

1 32 45 6 7

8

90 q

w

e

r

t

y

s

a

iopu

CONTROLS AND FUNCTIONS

Front Panel

1 STANDBY/ON

Turns on and sets this unit in the standby mode. When

you turn on this unit, you will hear a click and there will

be a 4 to 5-second delay before this unit can reproduce

sound.

Standby mode

In this mode, this unit consumes a small amount of

power to receive infrared-signals from the remote

control.

2 6CH (INPUT)

Selects the source connected to the 6CH INPUT jacks.

The source selected by pressing 6CH (INPUT) takes

priority over the source selected with INPUT (or the input

selector buttons on the remote control).

3 INPUT selector

Selects the input source you want to listen to or watch.

4 (INPUT) MODE

Sets the priority for the types of input signals (AUTO,

DTS, ANALOG) to receive when one component is

connected to two or more input jacks of this unit (see

page 29). Priority cannot be set when 6CH INPUT is

selected as the input source.

5 Remote control sensor

Receives signals from the remote control.

6 Front panel display

Shows information about the operational status of this

unit.

7 VOLUME

Controls the output level of all audio channels.

This does not affect the REC OUT level.

8 SPEAKERS A/B

Turn on or off the set of main speakers connected to the A

and/or B terminals on the rear panel at each time its

corresponding button is pressed.

9 BASS EXTENSION

Turns on or off the BASS EXTENSION function at each

time the button is pressed, this feature boosts the bass

frequency of the left and right main channels by +6 dB

(60 Hz) while maintaining overall tonal balance. This

boost is useful if you do not use a subwoofer.

0 PROCESSOR DIRECT

Turns on or off the PROCESSOR DIRECT function at

each time the button is pressed. When this is on, BASS,

TREBLE, and BASS EXTENSION are bypassed,

eliminating any alteration of the original signal.

5

English

INTRODUCTION PREPARATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONTROLS AND FUNCTIONS

D

I

G

I

T

A

L

N

ATUR

AL SOU

ND AV RECEIVER

H

TR-5990

To open, press gently on the lower part of the panel.

q STEREO/EFFECT

Switches the normal stereo or DSP effect reproduction.

When STEREO is selected, 2-channel input signals are

directed to the main left and right speakers without effect

sounds. All Dolby Digital and DTS audio signals except

for the LFE channel are mixed down to the main left and

right speakers.

w A/B/C/D/E

Selects one of the 5 preset station groups (A to E).

e PROGRAM l / h

Selects the DSP program.

r PRESET/TUNING l / h

Selects preset station number 1 to 8 when the colon (:)

appears next to the band indication on the front panel

display, and selects the tuning frequency when the colon

(:) does not appear.

t PHONES jack

Outputs audio signals for private listening with

headphones. When you connect headphones, no signals

are output to the OUTPUT jacks or to the speakers.

(There is an exception depending on the “1G SP B SET”

setting on the SET MENU.)

y VIDEO AUX jacks

Inputs audio and video signals from a portable external

source such as a game console. To reproduce source

signals from these jacks, select V-AUX as the input

source.

u PRESET/TUNING (EDIT)

Switches the function of PRESET/TUNING l / h (the

colon (:) turns on or off) between selecting a preset

station number and tuning.

This button is also used to exchange the assignment of

two preset stations with each other.

i FM/AM

Switches the reception band between FM and AM.

o MEMORY (MAN’L/AUTO FM)

Stores a station in the memory. Hold down this button for

more than 3 seconds to start automatic preset tuning.

p TUNING MODE (AUTO/MAN’L MONO)

Switches the tuning mode between automatic and manual.

To select the automatic tuning mode, press this button so

that the “AUTO” indicator lights up on the front panel

display. To select the manual tuning mode, press this

button so that the “AUTO” indicator does not light up.

a BASS

Adjusts the low-frequency response for the left and right

main channels.

Turn the control to the right to increase or to the left to

decrease the low-frequency response.

s TREBLE

Adjusts the high-frequency response for the left and right

main channels.

Turn the control to the right to increase or to the left to

decrease the high-frequency response.

Note

• If you increase or decrease the high-frequency or the low-

frequency sound to an extreme level, the tonal quality from the

center and rear speakers may not match that of the left and

right main speakers.

■ Opening and closing the front

panel door

When you want to use the controls behind the front panel

door, open the door by gently pressing on the lower part

of the panel. When you are not using them, close the door.

6

CONTROLS AND FUNCTIONS

PHONO

POWER SLEEP

CLEAR

LEARN

STANDBY

TRANSMIT

RE–NAME

6CH INPUT

SYSTEM

V

-

AUX

D

-

TV/LD

POWER

REC

DISC SKIP

SET MENU

TV INPUT

A/B/C/D/E

AUDIO

VOL

LEVEL

MENU

STEREO

HALL

ENTER-

TAINMENT

MUSIC

VIDEO

TV

THEATER

SELECT

EX/ES

0 +10

MOVIE

THEATER 1

MOVIE

THEATER 2

/DTS

SUR.

TEST

ON SCREEN

EFFECT

CHP/INDEX

TV VOL

RETURN

DISPLAY

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHURCH

CHCH

JAZZ CLUB

ROCK

CONCERT

TITLE

MUTE

POWER

AMP

AVTV

VCR2/DVRVCR 1 DVD

SELECT

CBL/SAT MD/TAPE CD-R

TUNER CD

+

–

3421

5

910

11 12

67 8

A

r

t

y

u

i

o

s

d

f

g

h

a

p

q

w

0

e

2

3

4

1

5

7

8

9

6

Remote Control

This section describes the controls and their functions of

the remote control to operate this unit. Functions written

in yellow are to operate this unit. Make sure that the AMP

mode is selected before operating this unit.

The functions written in green and white vary depending

on the input source selected.

1 Infrared window

Outputs infrared control signals. Aim this window at the

component you want to operate (see “Using the Remote

Control” on page 7).

2 TRANSMIT indicator

Flashes while the remote control is sending signals.

3 STANDBY

Sets this unit in the standby mode.

4 SYSTEM POWER

Turns on the power of this unit.

5

A

Sets the remote control to operate other components (not

necessarily connected to this unit) without changing this

unit’s input source (see page 54).

6 Input selector buttons

Select the input source and change the control area (see

“REMOTE CONTROL FEATURES” on pages 44 to 54).

7 Display window

Shows the selected source component that you are

controlling.

8 TV POWER

Turns on and off the power of the TV.

9 Operation Section

Provides functions such as play, stop, skip, etc. for

operating your other components.

0 LEVEL (TITLE)

Selects the effect speaker channel to be adjusted and sets

the level.

q Cursor buttons u / d / j / i

Selects and adjusts DSP program parameters and SET

MENU items.

TV MUTE/SELECT button mutes your TV volume and

selects menu items of your DVD player when their

manufacture codes are set.

w TEST (RETURN)

Outputs the test tone to adjust the speaker levels.

e DSP program (Numeric) buttons

Select DSP programs.

r RE-NAME

Used for changing the input source name in the display

window (see page 48).

t CLEAR

Used for clearing functions acquired when using the learn

and rename features, and set manufacturer codes (see

pages 48, 49).

y LEARN

Used for setting up the manufacturer code or for

programming the functions of other remote controls (see

pages 45-47).

u SLEEP

Sets the sleep timer.

i 6CH INPUT

Selects the source connected to the 6CH INPUT jacks.

7

English

INTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONTROLS AND FUNCTIONS

BASS

VOLUME

VIDEO AUXSILENT

PROGRAM

STEREO

SPEAKERS

6CH INPUT MODE

BASS

EXTENSION

PROCESSOR

DIRECT

PRESET

/

TUNING

PHONES

EFFECT

A/B/C/D/E

S VIDEO

MEMORY

FM/AM

EDIT

PRESET

/TUNING

MAN'L/AUTO FM AUTO/MAN'L MONO

TUNING

MODE

VIDEO AUDIO OPTICALLR

TUNER

STANDBY

/

ON

NATURAL SOUND AV RECEIVER

DSP

TREBLE

–

+

–

+

AB

DIGITAL

30° 30°

Approximately 6 m (20 feet)

o SELECT k/n

Selects the another component to control independently

from the input that has been selected by pressing an input

selector button.

p AV POWER

Turns on and off the power of the component selected by

the input selector button.

a AMP

Selects AMP or other component selected by the input

selector button.

s VOL +/–

Increases or decreases the volume level.

d MUTE

Mutes the sound. The MUTE indicator turns on when the

MUTE function is on. Press again to restore the audio

output to the previous volume level.

f SET MENU (MENU)

Selects the SET MENU mode.

g ON SCREEN (DISPLAY)

Displays the operation status of this unit and the

parameter settings for DSP programs on the monitor (see

page 23).

h STEREO/EFFECT

Switches the normal stereo or DSP effect reproduction.

When STEREO is selected, 2-channel input signals are

directed to the main left and right speakers without effect

sounds. All Dolby Digital and DTS audio signals except

for the LFE channel are also directed to the main left and

right speakers.

Using the Remote Control

The remote control transmits a directional infrared beam.

Be sure to aim the remote control directly at the remote

control sensor on the main unit during operation.

■ Handling the remote control

• Do not spill water or other liquids on the remote

control.

• Do not drop the remote control.

• Do not leave or store the remote control in the

following types of conditions:

– high humidity or temperature such as near a heater,

stove or bath;

– dusty places; or

– in places subject to extremely low temperatures.

8

CONTROLS AND FUNCTIONS

RL

LCR

RC RR

LFE

VIRTUAL

DTS

Neo

MOVIE TV THEATER

ENTERTAINMENT12

:6

DOLBY DIGITAL

PRO LOGIC

VCR DVD TUNER CD

PHONO

CD RV AUX

DSP

EX

MATRIXDISCRETE

ES

PCM

1

SILENT

SP

DIGITAL

VCR2/DVR

CBL

/

SAT

MD

/

TAPE

TV

/

LD

STEREO

TUNED

MEMORY

dB

ft

m

S

P. DIRECT

BASS

MUTE VOLUME

SLEEP

AUTO

D

PRO LOGIC

/

AB

0q r tyui o ap

2

1456789

w e

3

1

DSP

indicator

Lights up when you select a digital sound field program.

2 Decoder indicators

When any of the decoders equipped on this unit

functions, the indicator lights up.

3 VIRTUAL indicator

Lights up when using Virtual CINEMA DSP (see page

32).

4 Input source indicator

Shows the current input source with a cursor.

5 AUTO indicator

Shows that this unit is in the automatic tuning mode.

6 SLEEP indicator

Lights up while the sleep timer is on.

7 MUTE indicator

Flashes while the MUTE function is on.

8 BASS indicator

Lights up while BASS EXTENSION is on.

9 VOLUME level indicator

Indicates the volume level.

0 v indicator

Lights up when this unit is reproducing PCM (pulse code

modulation) digital audio signals.

q SILENT indicator

Lights up when headphones are connected with the sound

effect (see “SILENT CINEMA DSP” on page 32).

w SP A B indicator

Lights up according to which set of main speakers is

selected. Both indicators light up when both sets of

speakers are selected.

e Headphones indicator

Lights up when headphones are connected.

r DSP program indicators

The name of the selected DSP program lights up when

the ENTERTAINMENT, MOVIE THEATER 1, MOVIE

THEATER 2, TV THEATER or V/DTS SURROUND

DSP program is selected.

t Multi-information display

Shows the current DSP program name and other

information when adjusting or changing settings.

y STEREO indicator

Lights up when this unit is receiving a strong signal for an

FM stereo broadcast while the “AUTO” indicator is lit.

u TUNED indicator

Lights up when this unit tunes in to a station.

i MEMORY indicator

Flashes to show a station can be stored.

o P. DIRECT

Lights up while PROCESSOR DIRECT is on.

p Input channel indicator

Indicates the channel components of input signals being

received.

a

LFE

indicator

Lights up when the input signal contains the LFE signal.

Front Panel Display

9

English

INTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONTROLS AND FUNCTIONS

AC OUTLETS

CENTER

SUB

WOOFER

S VIDEO

MONITOR OUT

VIDEO

DIGITAL OUTPUT

DIGITAL

INPUT

6CH INPUT

GND

AUDIO AUDIO VIDEO

CONTROL

OUT

SPEAKERS

TUNER

REMOTE

IN

75Ω

UNBAL.

OUT

AM

ANT

GND

FM ANT

+12V

15mA

MAX.

COMPONENT VIDEO

S VIDEO

DVD

D-TV

/LD

CBL

/SAT

VIDEO

P

R

/ C

R

DVD

MONITOR

OUT

CBL

/SAT

MAIN

REAR

CENTER CENTER

OUTPUT

IMPEDANCE SELECTOR

SET BEFORE POWER ON

SUB

WOOFER

P

B

/ C

B

Y

R

L

R

L

R

L

OPTICAL

MD

/

TAPE

IN

(

PLAY

)

IN

(

PLAY

)

OUT

(

REC

)

OUT

(

REC

)

CD-R

MD/TAPE

CD-R

DVD

CBL

/SAT

CD

PHONO

IN

OUT

ZONE 2 OUT

VCR 2

/DVR

VCR 1

IN

MAIN

SURROUND

CD

D-TV

/LD

(SURROUND)

COAXIAL

+

–

+

–

+

–

+

–

MAIN A OR B:

A+B:

CENTER

4ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

6ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

REAR

REAR CENTER

:

MAIN A OR B:

CENTER

REAR

REAR CENTER

:

A

B

1

8

9 0 e rq

2

3

*1

4

6

7

5

w

(U.S.A. and Canada models)

1 DIGITAL OUTPUT jacks

2 Audio component jacks

See pages 17 and 18 for connection information.

3 Video component jacks

See pages 14 to 16 for connection information.

4 REMOTE IN/OUT jacks (U.S.A., Canada and

Australia models only)

See page 69 details.

5 CONTROL OUT (U.S.A., Canada and Australia

models only)

This is a control expansion terminal for commercial use.

6 AC power cord

Connect to a power outlet.

7 AC OUTLETS

Use these outlets to supply power to your other A/V

components (see page 21).

8 DIGITAL INPUT jacks

9 6CH INPUT jacks

See page 20 for connection information.

0 ZONE 2 OUT jacks (U.S.A., Canada and

Australia models only)

See page 68 for details.

q Antenna input terminals

See page 19 for connection information.

w SUBWOOFER jacks

See page 20 for connection information.

e Speaker terminals

See pages 11 and 12 for connection information.

r IMPEDANCE SELECTOR switch

Use this switch to match the amplifier output to your

speaker impedance (see page 13). Set this unit in the

standby mode before you change the setting of this

switch.

< China model only >

FREQUENCY STEP switch

See page 19.

VOLTAGE SELECTOR

See page 21.

*1 As this terminal is used for an examination in the factory, do not

connect any equipment to this terminal.

Rear Panel

10

SPEAKER SETUP

Speakers to Be Used

This unit has been designed to provide the best sound-

field quality with a 6-speaker system, using left and right

main speakers, left and right rear speakers, and a center

and rear center speakers. If you use different brands of

speakers (with different tonal qualities) in your system,

the tone of a moving human voice and other types of

sound may not shift smoothly. We recommend that you

use speakers from the same manufacturer or speakers

with the same tonal quality.

The main speakers are used for the main source sound

plus the effect sounds. They will probably be the speakers

from your present stereo system. The rear speakers are

used for the effect and surround sounds, and the center

speaker is for the center sounds (dialog, vocals, etc.). If

for some reason it is not practical to use a center speaker,

you can do without it. Best results, however, are obtained

with the full system.

The main speakers should be high-performance models

and have enough power-handling capacity to accept the

maximum output of your audio system. The other

speakers do not have to be equal to the main speakers. For

precise sound localization, however, it is ideal to use the

models of equivalent performance with the main

speakers.

■ Use of a subwoofer expands your

sound field

It is also possible to further expand your system with the

addition of a subwoofer. The use of a subwoofer is

effective not only for reinforcing bass frequencies from

any or all channels, but also for reproducing the LFE

(low-frequency effect) channel with high fidelity when

the Dolby Digital signal or the DTS signal is played back.

The YAMAHA Active Servo Processing Subwoofer

System is ideal for natural and lively bass reproduction.

PREPARATION

Speaker Placement

Refer to the following diagram when you place the

speakers.

■ Main speakers

Place the left and right main speakers an equal distance

from the ideal listening position. The distance of each

speaker from each side of the video monitor should be the

same.

■ Center speaker

Align the front face of the center speaker with the front

face of your video monitor. Place the speaker as close to

the monitor as possible, such as directly over or under the

monitor and centrally between the main speakers.

■ Rear speakers

Place these speakers behind your listening position,

facing slightly inwards, nearly 1.8 m (6 feet) above the

floor.

■ Rear center speaker

Place the rear center speaker in the center between the left

and right rear speakers at the same height from the floor

as the rear speakers.

■ Subwoofer

The position of the subwoofer is not so critical, because

low bass sounds are not highly directional. But it is better

to place the subwoofer near the main speakers. Turn it

slightly toward the center of the room to reduce the wall

reflections.

CAUTION

Use magnetically shielded speakers. If this type of

speakers still creates the interference with a monitor,

place the speakers away from the monitor.

Main

speaker (L)

1.8 m (6 feet)

Rear speaker (L)

Rear center

speaker

Rear speaker (R)

Subwoofer

Main speaker (R)Center speaker

Note

• If you do not use any effect speakers (rear, center and/or rear

center), change the settings of SPEAKER SET items in the

SET MENU to designate the signals to other terminals you

connect speakers to.

11

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SPEAKER SETUP

12

Connecting the Speakers

Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are

faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound

will be unnatural and lack bass.

CAUTION

• Use speakers with the specified impedance shown on the rear panel of this unit.

• Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could

damage this unit and/or speakers.

If necessary, use the SET MENU to change the speaker mode settings according to the number and size of the speakers

in your configuration after you finish connecting your speakers.

■ Speaker cables

A speaker cable is actually a pair of insulated cables

running side by side. One of the cables is colored or

shaped differently, perhaps with a stripe, groove or ridge.

1 Remove approximately 10 mm (3/8”) of

insulation from each of the speaker cables.

2 Twist the exposed wires of the cable

together to prevent short circuits.

■ Connecting to the SPEAKERS terminals

1 Unscrew the knob.

2 Insert one bare wire into the hole in the side

of each terminal.

3 Tighten the knob to secure the wire.

y

(For U.S.A., Canada, Australia and China models)

• Banana plug connections are also possible. First, tighten the

knob and then insert the banana plug connector into the end of

the corresponding terminal.

10 mm (3/8”)

■ MAIN SPEAKERS terminals

One or two speaker systems can be connected to these terminals. If you use only one speaker system, connect it to either

of the MAIN A or B terminals.

■ REAR SPEAKERS terminals

A rear speaker system can be connected to these terminals.

■ CENTER SPEAKER terminals

A center speaker can be connected to these terminals.

■ REAR CENTER SPEAKER terminals

A rear center speaker can be connected to these terminals.

Red: positive (+)

Black: negative (–)

Banana plug

3

1

2

12

SPEAKER SETUP

AC OUTLETS

CENTER

SUB

WOOFER

S VIDEO

MONITOR OUT

VIDEO

DIGITAL OUTPUT

DIGITAL

INPUT

6CH INPUT

GND

AUDIO AUDIO VIDEO

CONTROL

OUT

SPEAKERS

TUNER

REMOTE

IN

75Ω

UNBAL.

OUT

AM

ANT

GND

FM ANT

+12V

15mA

MAX.

COMPONENT VIDEO

S VIDEO

DVD

D-TV

/LD

CBL

/SAT

VIDEO

P

R

/ C

R

DVD

MONITOR

OUT

CBL

/SAT

MAIN

REAR

CENTER CENTER

OUTPUT

IMPEDANCE SELECTOR

SET BEFORE POWER ON

SUB

WOOFER

P

B

/ C

B

Y

R

L

R

L

R

L

OPTICAL

MD

/

TAPE

IN

(

PLAY

)

IN

(

PLAY

)

OUT

(

REC

)

OUT

(

REC

)

CD-R

MD/TAPE

CD-R

DVD

CBL

/SAT

CD

PHONO

IN

OUT

ZONE 2 OUT

VCR 2

/DVR

VCR 1

IN

MAIN

SURROUND

CD

D-TV

/LD

(SURROUND)

COAXIAL

+

–

+

–

+

–

+

–

MAIN A OR B:

A+B:

CENTER

4ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

6ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

REAR

REAR CENTER

:

MAIN A OR B:

CENTER

REAR

REAR CENTER

:

A

B

2

6745

31

Subwoofer

system

Rear Center

speaker

Main B speaker

Center

speaker

(U.S.A. and Canada

models)

Right

Rear speaker

■ SUBWOOFER jack

When using a subwoofer with built-in amplifier, including the YAMAHA Active Servo Processing Subwoofer System,

connect the input jack of the subwoofer system to this jack. Low bass signals distributed from the main, center and/or

rear channels are directed to this jack if they are assigned to this jack. (The cut-off frequency of this jack is 90 Hz.) The

LFE (low-frequency effect) signals generated when Dolby Digital or DTS is decoded are also directed if they are

assigned to this jack.

Note

• Depending on the settings of “1 SPEAKER SET” and “10 LFE LEVEL” on the SET MENU, some signals may not be output from

the SUBWOOFER jack.

Right Left

Main A speaker

Right Left

Left

2

3

1

6

7

5

4

The diagram above shows the speaker layout in the

listening room.

13

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SPEAKER SETUP

AC OUTLETS

IMPEDANCE SELECTOR

SET BEFORE POWER ON

MAIN A OR B:

A+B:

CENTER

4ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

6ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

REAR

REAR CENTER

:

MAIN A OR B:

CENTER

REAR

REAR CENTER

:

IMPEDANCE SELECTOR

SET BEFORE POWER ON

MAIN A OR B:

A+B:

CENTER

4ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

6ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

REAR

REAR CENTER

:

MAIN A OR B:

CENTER

REAR

REAR CENTER

:

Switch

position

Left

Right

Speaker

Main

Center

Rear

Center

Rear

Main

Center

Rear

Center

Rear

Impedance level

If you use one set of main speakers, the impedance of

each speaker must be 4 Ω or higher.

If you use two sets of main speakers, the impedance of

each speaker must be 8 Ω or higher.

The impedance must be 6 Ω or higher.

The impedance of each speaker must be 6 Ω or higher.

If you use one set of main speakers, the impedance of

each speaker must be 8 Ω or higher.

If you use two sets of main speakers, the impedance of

each speaker must be 16 Ω or higher.

[U.S.A. and Canada models]

The impedance of each speaker must be 8 Ω or higher.

The impedance must be 8 Ω or higher.

The impedance of each speaker must be 8 Ω or higher.

IMPEDANCE

SELECTOR

switch

(U.S.A. and Canada models)

■ IMPEDANCE SELECTOR switch

WARNING

Do not change the IMPEDANCE SELECTOR switch setting while the power of this unit is on, otherwise this unit

may be damaged.

If this unit fails to turn on when STANDBY/ON (or SYSTEM POWER) is pressed, the IMPEDANCE SELECTOR

switch may not be fully slid to either position. If so, slide the switch to either position fully when this unit is in the

standby mode.

Select the left and right position according to the impedance of the speakers in your system. Be sure to move this switch

only when this unit is in the standby mode.

14

Before Connecting Components

CAUTION

Never connect this unit and other components to mains

power until all connections between components have

been completed.

• Be sure all connections are made correctly, that is to

say L (left) to L, R (right) to R, “+” to “+” and “–” to

“–”. Some components require different connection

methods and have different jack names. Refer to the

operation instructions for each component to be

connected to this unit.

• Use commercially available video pin cables when

connecting to the S VIDEO and COMPONENT

VIDEO jacks.

Connecting Video Components

■ About the video jacks

There are three types of video jacks.

VIDEO jacks transmit composite signals.

S VIDEO jacks transmit S-video signals.

S-video signals are separated into

luminance (Y) and color (C) video signals

to achieve high-quality color

reproduction.

COMPONENT VIDEO jacks transmit

component signals.

Component signals are separated into

luminance (Y) and color difference (P

B /

C

B, PR/CR) to provide the best quality in

picture reproduction.

Refer to the owner’s manuals for your monitor and other

components being connected to reproduce these signals

correctly.

You can connect an S-video output and component video

output of your video components to this unit. Connect an

S-video output to the S VIDEO jack and component video

output to the COMPONENT VIDEO jack on this unit.

CONNECTIONS

S VIDEO VIDEO

L AUDIO R OPTICAL

VIDEO AUX

AUDIO OUT R

AUDIO OUT L

VIDEO OUT

OPTICAL OUT

S VIDEO OUT

O

V

L

R

S

Game

console or

video camera

VIDEO

VIDEO jack

S VIDEO

S VIDEO jack

COMPONENT VIDEO

PR/ CR PB/ CB Y

COMPONENT VIDEO jacks

y

• The COMPONENT VIDEO jacks on this unit are independent

of the S VIDEO and VIDEO jacks.

• Connection depends on the availability of input jacks on your

monitor. The signals input through the S VIDEO jacks can be

converted to composite signals inside of this unit and output

through the VIDEO jacks on this unit as well.

• When signals input through both S VIDEO and VIDEO jacks,

signals input through the S VIDEO jack has priority.

• You can designate the input for the COMPONENT VIDEO A

and B jacks according to your component by using “7 I/O

ASSIGNMENT” on the SET MENU (see pages 61 and 62 for

details).

Note

• When you are using the COMPONENT VIDEO jacks, check

the details in the owner’s manual that came with the component

being connected.

■ VIDEO AUX jacks (on the front

panel)

These jacks are used to connect any video input source

such as a game console and a camcorder to this unit.

15

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONNECTIONS

CENTER

SUB

WOOFER

S VIDEO

MONITOR OUT

VIDEO

DIGITAL OUTPUT

DIGITAL

INPUT

6CH INPUT

GND

AUDIO AUDIO VIDEO

TUNER

75Ω

UNBAL.

AM

ANT

GND

FM ANT

COMPONENT VIDEO

S VIDEO

DVD

D-TV

/LD

CBL

/SAT

VIDEO

PR/ CR

DVD

MONITOR

OUT

CBL

/ SAT

CENTER

OUTPUT

SUB

WOOFER

PB/ CB Y

R

L

R

L

OPTICAL

MD

/

TAPE

IN

(

PLAY

)

IN

(

PLAY

)

OUT

(

REC

)

OUT

(

REC

)

CD-R

MD/TAPE

CD-R

DVD

CBL

/SAT

CD

PHONO

IN

OUT

ZONE 2 OUT

VCR 2

/DVR

VCR 1

IN

MAIN

SURROUND

CD

D-TV

/LD

COAXIAL

+

–

V

S

L R

VVC

S S

L R

O

L

S

R

V

C

O

COMPONENT

INPUT

S VIDEO

INPUT

VIDEO

INPUT

S VIDEO

OUTPUT

VIDEO

OUTPUT

AUDIO OUTPUT

COAXIAL OUTPUT

OPTICAL OUTPUT

AUDIO OUTPUT

COMPONENT OUTPUT

VIDEO

OUTPUT

S VIDEO

OUTPUT

V V V

V

V V V

indicates S-video cables

indicates video pin cables

indicates coaxial cables

indicates optical cables

indicates right audio pin cables

indicates left audio pin cables

indicates signal direction

Video

monitor

TV/digital TV or

LD player

(U.S.A. and Canada

models)

DVD player

indicates component video cables

16

CONNECTIONS

CENTER

SUB

WOOFER

S VIDEO

MONITOR OUT

VIDEO

DIGITAL OUTPUT

DIGITAL

INPUT

6CH INPUT

GND

AUDIO AUDIO VIDEO

TUNER

75Ω

UNBAL.

AM

ANT

GND

FM ANT

COMPONENT VIDEO

S VIDEO

DVD

D-TV

/LD

CBL

/SAT

VIDEO

PR/ CR

DVD

MONITOR

OUT

CBL

/ SAT

PB/ CB Y

R

L

R

L

OPTICAL

MD

/

TAPE

IN

(

PLAY

)

IN

(

PLAY

)

OUT

(

REC

)

OUT

(

REC

)

CD-R

MD/TAPE

CD-R

DVD

CBL

/SAT

CD

PHONO

IN

OUT

ZONE 2 OUT

VCR 2

/DVR

VCR 1

IN

MAIN

SURROUND

CD

D-TV

/LD

COAXIAL

COMPONENT

INPUT

V

S

L R

VV

S S S

L R L R

O

S VIDEO OUTPUTVIDEO OUTPUT

AUDIO OUTPUT

OPTICAL OUTPUT

S VIDEO

INPUT

S VIDEO

OUTPUT

S VIDEO INPUT

VIDEO

OUTPUT

V

VIDEO

INPUT

AUDIO INPUT

AUDIO OUTPUT

VIDEO

INPUT

COMPONENT OUTPUT

V V V

VVV

L

S

R

V

O

V

indicates S-video cables

indicates video pin cables

indicates optical cables

indicates right audio pin cables

indicates left audio pin cables

indicates signal direction

Video

monitor

(U.S.A. and

Canada

models)

VCR 1 or VCR 2/

DVR (digital

video recorder)

Cable TV or

Satellite tuner

indicates component video cables

Pagina se încarcă ...

Yamaha HTR-5990 Manualul proprietarului

Acest manual este potrivit și pentru

Yamaha HTR-5990 Manualul proprietarului

în alte limbi

Lucrări conexe