Yamaha RX-V630 Manual de utilizare

Marca: Yamaha

Model: RX-V630

Categorie: Receptoare AV

Tip: Manual de utilizare

OWNER’S MANUAL

RX-V630

AV Receiver

0100V630(U)-cv1 12/27/01, 7:45 PM1

I CAUTION

SAFETY INSTRUCTIONS

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to alert

you to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may

be of sufficient magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert you to the presence of

important operating and maintenance (servicing)

instructions in the literature accompanying the

appliance.

1 Read Instructions – All the safety and operating instructions

should be read before the product is operated.

2 Retain Instructions – The safety and operating instructions

should be retained for future reference.

3 Heed Warnings – All warnings on the product and in the

operating instructions should be adhered to.

4 Follow Instructions – All operating and use instructions

should be followed.

5 Cleaning – Unplug this product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol cleaners.

Use a damp cloth for cleaning.

6 Attachments – Do not use attachments not recommended

by the product manufacturer as they may cause hazards.

7 Water and Moisture – Do not use this product near water –

for example, near a bath tub, wash bowl, kitchen sink, or

laundry tub; in a wet basement; or near a swimming pool;

and the like.

8 Accessories – Do not place this product on an unstable cart,

stand, tripod, bracket, or table. The product may fall,

causing serious injury to a child or adult, and serious

damage to the product. Use only with a cart, stand, tripod,

bracket, or table recommended by the manufacturer, or sold

with the product. Any mounting of the product should

follow the manufacturer’s instructions, and should use a

mounting accessory recommended by the manufacturer.

9 A product and cart combination should be

moved with care. Quick stops, excessive

force, and uneven surfaces may cause the

product and cart combination to overturn.

10 Ventilation – Slots and openings in the cabinet are provided

for ventilation and to ensure reliable operation of the

product and to protect it from overheating, and these

openings must not be blocked or covered. The openings

should never be blocked by placing the product on a bed,

sofa, rug, or other similar surface. This product should not

be placed in a built-in installation such as a bookcase or

rack unless proper ventilation is provided or the

manufacturer’s instructions have been adhered to.

11 Power Sources – This product should be operated only from

the type of power source indicated on the marking label. If

you are not sure of the type of power supply to your home,

consult your product dealer or local power company. For

products intended to operate from battery power, or other

sources, refer to the operating instructions.

12 Grounding or Polarization – This product may be equipped

with a polarized alternating current line plug (a plug having

one blade wider than the other). This plug will fit into the

power outlet only one way. This is a safety feature. If you

are unable to insert the plug fully into the outlet, try

reversing the plug. If the plug should still fail to fit, contact

your electrician to replace your obsolete outlet. Do not

defeat the safety purpose of the polarized plug.

13 Power-Cord Protection – Power-supply cords should be

routed so that they are not likely to be walked on or pinched

by items placed upon or against them, paying particular

attention to cords at plugs, convenience receptacles, and the

point where they exit from the product.

14 Lightning – For added protection for this product during a

lightning storm, or when it is left unattended and unused for

long periods of time, unplug it from the wall outlet and

disconnect the antenna or cable system. This will prevent

damage to the product due to lightning and power-line

surges.

15 Power Lines – An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into such

power lines or circuits. When installing an outside antenna

system, extreme care should be taken to keep from touching

such power lines or circuits as contact with them might be

fatal.

16 Overloading – Do not overload wall outlets, extension

cords, or integral convenience receptacles as this can result

in a risk of fire or electric shock.

17 Object and Liquid Entry – Never push objects of any kind

into this product through openings as they may touch

dangerous voltage points or short-out parts that could result

in a fire or electric shock. Never spill liquid of any kind on

the product.

18 Servicing – Do not attempt to service this product yourself

as opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all servicing to

qualified service personnel.

19 Damage Requiring Service – Unplug this product from the

wall outlet and refer servicing to qualified service personnel

under the following conditions:

a) When the power-supply cord or plug is damaged,

b) If liquid has been spilled, or objects have fallen into

the product,

c) If the product has been exposed to rain or water,

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

0101V630_Cau_EN(U) 12/27/01, 7:45 PM2

SAFETY INSTRUCTIONSSAFETY INSTRUCTIONS

CAUTION II

1. IMPORTANT NOTICE : DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved

by Yamaha may void your authority, granted by the

FCC, to use the product.

2. IMPORTANT : When connecting this product to

accessories and/or another product use only high

quality shielded cables. Cable/s supplied with this

product MUST be used. Follow all installation

instructions. Failure to follow instructions could void

your FCC authorization to use this product in the USA.

3. NOTE : This product has been tested and found to

comply with the requirements listed in FCC

Regulations, Part 15 for Class “B” digital devices.

Compliance with these requirements provides a

reasonable level of assurance that your use of this

product in a residential environment will not result in

harmful interference with other electronic devices.

This equipment generates/uses radio frequencies and,

if not installed and used according to the instructions

found in the users manual, may cause interference

harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee

that interference will not occur in all installations. If

this product is found to be the source of interference,

which can be determined by turning the unit “OFF” and

“ON”, please try to eliminate the problem by using one

of the following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient

the antenna. If the antenna lead-in is 300 ohm ribbon

lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to

distribute this type of product. If you can not locate the

appropriate retailer, please contact Yamaha Electronics

Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA

90620.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

EXAMPLE OF ANTENNA GROUNDING

MAST

GROUND

CLAMP

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810–20)

GROUNDING CONDUCTORS

(NEC SECTION 810–21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250. PART H)

ELECTRIC

SERVICE

EQUIPMENT

NEC

– NATIONAL ELECTRICAL CODE

FCC INFORMATION (for US customers only)

Note to CATV system installer:

This reminder is provided to call the CATV system

installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in particular,

specifies that the cable ground shall be connected to the

grounding system of the building, as close to the point of

cable entry as practical.

d) If the product does not operate normally by following

the operating instructions. Adjust only those controls

that are covered by the operating instructions as an

improper adjustment of other controls may result in

damage and will often require extensive work by a

qualified technician to restore the product to its

normal operation,

e) If the product has been dropped or damaged in any

way, and

f) When the product exhibits a distinct change in

performance - this indicates a need for service.

20 Replacement Parts – When replacement parts are

required, be sure the service technician has used

replacement parts specified by the manufacturer or have

the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric

shock, or other hazards.

21 Safety Check – Upon completion of any service or

repairs to this product, ask the service technician to

perform safety checks to determine that the product is in

proper operating condition.

22 Wall or Ceiling Mounting – The unit should be mounted

to a wall or ceiling only as recommended by the

manufacturer.

23 Heat – The product should be situated away from heat

sources such as radiators, heat registers, stoves, or other

products (including amplifiers) that produce heat.

24 Outdoor Antenna Grounding – If an outside antenna or

cable system is connected to the product, be sure the

antenna or cable system is grounded so as to provide some

protection against voltage surges and built-up static

charges. Article 810 of the National Electrical Code, ANSI/

NFPA 70, provides information with regard to proper

grounding of the mast and supporting structure, grounding

of the lead-in wire to an antenna discharge unit, size of

grounding conductors, location of antenna discharge unit,

connection to grounding electrodes, and requirements for

the grounding electrode.

0101V630_Cau_EN(U) 12/27/01, 7:45 PM3

1 To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

2 Install this unit in a well ventilated, cool, dry, clean

place with at least 30 cm on the top, 20 cm on the

left and right, and 10 cm at the back of this unit

— away from direct sunlight, heat sources,

vibration, dust, moisture, and/or cold.

3 Locate this unit away from other electrical

appliances, motors, or transformers to avoid

humming sounds. To prevent fire or electrical

shock, do not place this unit where it may get

exposed to rain, water, and/or any type of liquid.

4 Do not expose this unit to sudden temperature

changes from cold to hot, and do not locate this

unit in a environment with high humidity (i.e. a

room with a humidifier) to prevent condensation

inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal

injury.

5 On the top of this unit, do not place:

– Other components, as they may cause damage

and/or discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may

cause fire, damage to this unit, and/or personal

injury.

– Containers with liquid in them, as they may

cause electrical shock to the user and/or

damage to this unit.

6 Do not cover this unit with a newspaper,

tablecloth, curtain, etc. in order not to obstruct

heat radiation. If the temperature inside this unit

rises, it may cause fire, damage to this unit, and/or

personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may

overheat, possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cord from the wall

outlet, grasp the plug; do not pull the cord.

11 Do not clean this unit with chemical solvents; this

might damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used.

Using this unit with a higher voltage than

specified is dangerous and may cause fire,

damage to this unit, and/or personal injury.

YAMAHA will not be held responsible for any

damage resulting from use of this unit with a

voltage other than specified.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

13 To prevent damage by lightning, disconnect the

power cord from the wall outlet during an

electrical storm.

14 Take care of this unit so that no foreign objects

and/or liquid drops inside this unit.

15 Do not attempt to modify or fix this unit. Contact

qualified YAMAHA service personnel when any

service is needed. The cabinet should never be

opened for any reasons.

16 When not planning to use this unit for long

periods of time (i.e. vacation), disconnect the AC

power plug from the wall outlet.

17 Be sure to read the “TROUBLESHOOTING” section

on common operating errors before concluding

that this unit is faulty.

18 Before moving this unit, press STANDBY/ON to set

this unit in the standby mode, and disconnect the

AC power plug from the wall outlet.

19 VOLTAGE SELECTOR (China and General models

only)

The VOLTAGE SELECTOR on the rear panel of this

unit must be set for your local main voltage

BEFORE plugging into the AC main supply.

Voltages are 110/120/220/240 V AC, 50/60 Hz.

This unit is not disconnected from the AC power

source as long as it is connected to the wall outlet,

even if this unit itself is turned off. This state is called

the standby mode. In this state, this unit is designed to

consume a very small quantity of power.

IMPORTANT

Please record the serial number of this unit in the

space below.

MODEL:

Serial No.:

The serial number is located on the rear of the unit.

Retain this Owner’s Manual in a safe place for future

reference.

FOR CANADIAN CUSTOMERS

To prevent electric shock, match wide blade of plug to

wide slot and fully insert.

This Class B digital apparatus complies with Canadian

ICES-003.

III CAUTION

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s Consumer

Electronics Group want you to get the most out of your equipment

by playing it at a safe level. One that lets the sound come through

loud and clear without annoying blaring or distortion – and, most

importantly, without affecting your sensitive hearing.

Since hearing damage from loud sounds is often

undetectable until it is too late, YAMAHA and the

Electronic Industries Association’s Consumer

Electronics Group recommend you to avoid

prolonged exposure from excessive volume levels.

0101V630_Cau_EN(U) 12/27/01, 7:45 PM4

English

INTRODUCTION

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

CONTENTS

INTRODUCTION

CONTENTS ............................................................ 1

FEATURES ............................................................. 2

GETTING STARTED ............................................ 3

Checking the package contents ................................. 3

Installing batteries in the remote control ................... 3

CONTROLS AND FUNCTIONS ......................... 4

Front panel ................................................................ 4

Remote control .......................................................... 6

Using the remote control ........................................... 7

Front panel display .................................................... 8

PREPARATION

SPEAKER SETUP ................................................. 9

Speakers .................................................................... 9

Speaker placement .................................................... 9

Connecting the speakers .......................................... 10

CONNECTIONS .................................................. 13

Before connecting components ............................... 13

Connecting video components ................................ 14

Connecting audio components ................................ 16

Connecting the antennas ......................................... 17

Connecting an external amplifier ............................ 18

Connecting an external decoder .............................. 18

Connecting the power supply cords ........................ 19

Turning on the power .............................................. 19

SPEAKER MODE SETTINGS .......................... 20

ADJUSTING SPEAKER OUTPUT LEVELS .. 21

Before you begin ..................................................... 21

Using the test tone ................................................... 21

BASIC OPERATION

BASIC PLAYBACK ............................................ 23

Input modes and indications .................................... 25

Selecting a sound field program .............................. 26

DIGITAL SOUND FIELD PROCESSING

(DSP) ................................................................. 29

Understanding sound fields ..................................... 29

Hi-Fi DSP programs ................................................ 29

CINEMA-DSP ...................................................... 30

Sound design of CINEMA-DSP ............................. 30

CINEMA-DSP programs ........................................ 32

TUNING ................................................................ 34

Automatic and manual tuning ................................. 34

Presetting stations .................................................... 35

Tuning in to a preset station .................................... 37

Exchanging preset stations ...................................... 37

SLEEP TIMER ..................................................... 38

Setting the sleep timer ............................................. 38

Canceling the sleep timer ........................................ 38

RECORDING ....................................................... 39

ADVANCED OPERATION

SET MENU ........................................................... 40

Adjusting the items on the SET MENU .................. 40

1 SPEAKER SET (speaker mode settings) ............ 41

2 LFE LEVEL ........................................................ 43

3 SP DLY TIME (speaker delay time) ................... 43

4 D. RANGE (dynamic range) ............................... 44

5 L/R BALANCE (balance of the main left and

right speakers) ..................................................... 44

6 HP TONE CTRL (headphone tone control) ........ 44

7 I/O ASSIGN (input/output assignment) .............. 44

8 INPUT MODE (initial input mode) .................... 45

9 DISPLAY SET .................................................... 45

10MEM. GUARD (memory guard) ........................ 45

REMOTE CONTROL FEATURES ................... 46

Control area ............................................................. 46

Setting the manufacturer code ................................. 47

Clearing setup manufacturer codes ......................... 47

Controlling other components ................................. 48

ADJUSTING THE LEVEL OF THE EFFECT

SPEAKERS ....................................................... 49

ADJUSTING THE DELAY TIME ..................... 50

ADJUSTING THE PARAMETER SETTINGS

FOR PRO LOGIC

MUSIC ......................... 51

Changing parameter settings ................................... 51

PRO LOGIC Music parameter descriptions ....... 51

ADDITIONAL INFORMATION

TROUBLESHOOTING ...................................... 52

GLOSSARY .......................................................... 56

SPECIFICATIONS .............................................. 58

0102V630_1-8_EN(U) 12/27/01, 7:45 PM1

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are trademarks

of Dolby Laboratories.

“DTS”, “ES” and “DTS Digital Surround” are trademarks of

Digital Theater Systems, Inc.

FEATURES

Built-in 6-channel power amplifier

◆ Minimum RMS output power

(0.06% THD, 20 Hz – 20 kHz, 8Ω)

Main: 75 W + 75 W

Center: 75 W

Rear: 75 W + 75 W

Rear center: 75 W

Multi-mode digital sound field

processing

◆ Dolby Pro Logic/Dolby Pro Logic decoder

◆ Dolby Digital/Dolby Digital EX decoder

◆ DTS/DTS-ES compatible decoder

◆ CINEMA DSP: Combination of YAMAHA DSP

technology and Dolby Pro Logic, Dolby Digital

or DTS

◆ Virtual CINEMA DSP

◆ SILENT CINEMA DSP

Sophisticated AM/FM Tuner

◆ 40-Station random access preset tuning

◆ Automatic preset tuning

◆ Preset station shifting capability (Preset

editing)

Other features

◆ 96-kHz/24-bit D/A converter

◆ “SET MENU” for optimizing this unit for your

Audio/Video system

◆ Test tone generator for easier speaker balance

adjustment

◆ 6-channel external decoder input

◆ S-video signal input/output capability

◆ Component video input/output capability

◆ Optical and coaxial digital audio signal jacks

◆ Sleep timer

◆ Remote control with preset manufacturer codes

■ About this manual

• y indicates a tip for your operation.

• Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button

names differ between the main unit and the remote control, the button name on the remote control is given in parentheses.

• This manual is printed prior to production. Design and specifications are subject to change in part for the reason of the improvement

in operativity ability, and others. In this case, the product has priority.

0102V630_1-8_EN(U) 12/27/01, 7:45 PM2

English

INTRODUCTION PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

POWER

SLEEP

CODE SET

STANDBY

TRANSMIT

6CH INPUT

SYSTEM

AUX

TV/CBL

REC

DISC SKIP

SET MENU

SELECT

PRESET/CH

TV INPUTTV MUTE

A/B/C/D/E

AUDIO

VOLUME

LEVEL

TEST

STEREO

EFFECT

RETURN

DISPLAY

TITLE

MUTE

AMP

POWER POWER

AVTV

VCR 1 VCR2/DVR

DVD

MD/CD-R TUNERCD

–

TV CHTV VOL

–

HALL

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

SELECT

EX/ES

MOVIE

THEATER 1

MOVIE

THEATER 2

/DTS

SUR.

ROCK

CONCERT

JAZZ CLUB

3421

ENTER

+10

67 8

Installing batteries in the remote

control

Insert the batteries in the correct direction by aligning the

+ and – marks on the batteries with the polarity markings

(+ and –) inside the battery compartment.

1 Press the part and slide off the battery

compartment cover.

2 Insert the four supplied batteries (AAA, R03,

UM-4) according to the polarity markings on

the inside of the battery compartment.

3 Slide the cover back on so that it snaps into

place.

■ Notes on batteries

• Change all of the batteries if you notice a decrease in

the operating range of the remote control, that the

indicator does not flash, or the light becoming dim.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline

and manganese batteries) together. Read the packaging

carefully as these different types of batteries may have

the same shape and color.

• If the batteries have leaked, dispose of them

immediately. Avoid touching the leaked material or

letting it come into contact with clothing, etc. Clean

the battery compartment thoroughly before installing

new batteries.

If the remote control is without batteries for more than

2 minutes, or if exhausted batteries remain in the

remote control, the contents of the memory may be

cleared. When the memory is cleared, insert new

batteries, set up the manufacturer code that may have

been cleared.

AM loop antenna

(Europe, U.K., Australia and

Singapore models)

Indoor FM antenna

(U.S.A., Canada, China,

Korea and General models)

Batteries (4)

(AAA, R03, UM-4)

Remote control

GETTING STARTED

Checking the package contents

Check your package to make sure it contains the following items.

75-ohm/300-ohm antenna

adapter (U.K. model)

Front VIDEO AUX jack cap

0102V630_1-8_EN(U) 12/27/01, 7:45 PM3

NATURAL SOUND AV RECEIVER

SPEAKERS

SILENT

PHONES

STANDBY

STEREO

EFFECT

PROGRAM

BASS

– + – +

TREBLE

VIDEO AUX

S VIDEO VIDEO AUDIO OPTICALLR

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

VOLUME

INPUT

INPUT M0DE

6CH INPUT

PRESET

TUNING

A/B/C/D/E

123 456

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

iupo

90 ert8qw y

CONTROLS AND FUNCTIONS

Front panel

1 STANDBY/ON

Turns this unit on, or set it to the standby mode. When

you turn this unit on, you will hear a click and there will

be a 4 to 5-second delay before this unit can reproduce

sound.

Standby mode

In this mode, this unit will consume a small amount of

power in order to receive infrared-signals from the

remote control.

2 Remote control sensor

Receives signals from the remote control.

3 Front panel display

Shows information about the operational status of this

unit.

4 INPUT MODE

Sets the priority for the types of input signals (AUTO,

DTS, ANALOG) to receive when one component is

connected to two or more input jacks. Priority cannot be

set when 6CH INPUT is selected as the input source.

5 INPUT l / h

Selects the input source you want to listen to or watch.

6 VOLUME

Controls the output level of all audio channels.

This does not affect the OUT (REC) level.

7 6CH INPUT

Selects the audio source connected to the 6CH INPUT

jacks. This audio takes priority over the source selected

with INPUT l / h (or the input selector buttons on the

remote control).

8 SILENT (PHONES jack)

Allows you enjoy DSP effect for private listening with

headphones. When you connect headphones, no signals

are output to the speakers or the OUTPUT jacks.

9 SPEAKERS A/B

Turns the set of main speakers connected to the A and/or

B terminals on or off.

0102V630_1-8_EN(U) 12/27/01, 7:45 PM4

English

INTRODUCTION PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONTROLS AND FUNCTIONS

0 STEREO/EFFECT

Switches between normal stereo and DSP effect

reproduction. When STEREO is selected, 2-channel

signals are directed to the main left and right speakers

without effect sounds and all Dolby Digital and DTS

signals (except the LFE channel) are mixed down to the

main left and right speakers.

q PROGRAM l / h

Selects the DSP program.

w PRESET/TUNING l / h

Selects preset station numbers 1 to 8 when the colon (:)

appears in the front panel display.

Selects the tuning frequency when the colon (:) does not

appear.

e A/B/C/D/E

Selects preset station groups A to E.

r BASS

Adjusts the low-frequency response for the main left and

right channels.

Turn right to increase or turn left to decrease the low-

frequency response.

t TREBLE

Adjusts the high-frequency response for the main left and

right channels.

Turn right to increase or turn left to decrease the high-

frequency response.

y VIDEO AUX jacks

Inputs for audio and video signals from a portable

external source (game console, etc.). Set the input source

to V-AUX to enjoy source signals from these jacks.

When the VIDEO AUX jacks on the front panel are not

used, you can attach the provided front VIDEO AUX jack

cap as shown in the illustration. When the cap is not

attached, be sure retain it carefully.

u PRESET/TUNING (EDIT)

Switches the function of PRESET/TUNING l / h

between selecting a preset station number and tuning (the

colon (:) turns on or off).

This button is also used to exchange the assignment of

two preset stations with each other.

i TUNING MODE (AUTO/MAN’L MONO)

Switches the tuning mode between automatic and manual.

o MEMORY (MAN’L/AUTO FM)

Stores the current station in the memory.

p FM/AM

Switches the reception band between FM and AM.

TICA

VID

S VID

VID

0102V630_1-8_EN(U) 12/27/01, 7:45 PM5

CONTROLS AND FUNCTIONS

POWER

SLEEP

CODE SET

STANDBY

TRANSMIT

6CH INPUT

SYSTEM

AUX

TV/CBL

REC

DISC SKIP

SET MENU

SELECT

PRESET/CH

TV INPUT

TV MUTE

A/B/C/D/E

AUDIO

VOLUME

LEVEL

TEST

STEREO

EFFECT

RETURN

DISPLAY

TITLE

MUTE

AMP

POWER POWER

AVTV

VCR 1 VCR2/DVR

DVD

MD/CD-R TUNERCD

–

TV CHTV VOL

–

HALL

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

SELECT

EX/ES

MOVIE

THEATER 1

MOVIE

THEATER 2

/DTS

SUR.

ROCK

CONCERT

JAZZ CLUB

3421

ENTER

+10

67 8

Remote control

This section describes the remote control controls and

their functions. Make sure that the AMP mode is selected

before starting operation. See “REMOTE CONTROL

FEATURES” on pages 46 to 48.

1 Infrared window

Outputs infrared control signals. Aim this window at the

component you want to operate.

2 CODE SET

Used when setting up the manufacturer code (see page

47).

3 Input selector buttons

Select the input source and set the remote control to

operate the selected source component.

4 DSP program

Select DSP programs for the AMP position. Press a

button repeatedly to select a DSP program within that

group.

5 LEVEL

Selects the effect speaker channel to be adjusted.

6 Multi control section

Used when changing the setting and to implement the

settings.

7 TEST

Outputs the test tone to adjust the speaker levels.

8 TRANSMIT indicator

Flashes while the remote control is sending signals.

9 STANDBY

Sets this unit in the standby mode.

0 SYSTEM POWER

Turns on the power of this unit.

q SLEEP

Sets the sleep timer.

w 6CH INPUT

Selects the audio source connected to the 6CH INPUT

jacks.

e AMP

Sets the remote control to the AMP mode for controlling

this unit.

r Å

Sets the remote control to operate other component (not

necessarily connected to this unit) without changing this

unit’s input source.

t VOLUME +/–

Increases or decreases the volume level.

y MUTE

Mutes the sound. Press again to restore the audio output

to the previous volume level.

0102V630_1-8_EN(U) 12/27/01, 7:45 PM6

English

INTRODUCTION PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONTROLS AND FUNCTIONS

VCR 1 VCR2/DVR

NATURAL SOUND AV RECEIVER

SPEAKERS

SILENT

PHONES

STANDBY

STEREO

EFFECT

PROGRAM

PRESET

TUNING

A/B/C/D/E

BASS

– + – +

TREBLE

VIDEO AUX

S VIDEO VIDEO AUDIO OPTICALLR

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FMAUTO/MAN'L MONO

TUNING MODE

VOLUMEINPUT

INPUT M0DE

6CH INPUT

30° 30°

Approximately 6 m (20 feet)

u STEREO/EFFECT

Switches between normal stereo and DSP effect

reproduction. When STEREO is selected, 2-channel

signals are directed to the main left and right speakers

without effect sounds and all Dolby Digital and DTS

signals (except the LFE channel) are mixed down to the

main left and right speakers.

i SET MENU

Selects the SET MENU mode.

Using the remote control

The remote control transmits a directional infrared beam.

Be sure to aim the remote control directly at the remote

control sensor on the main unit during operation.

■ Handling the remote control

• Do not spill water or other liquids on the remote

control.

• Do not drop the remote control.

• Do not leave or store the remote control in the

following types of conditions:

– high humidity or temperature such as near a heater,

stove or bath;

– dusty places; or

– in places subject to extremely low temperatures.

0102V630_1-8_EN(U) 12/27/01, 7:45 PM7

CONTROLS AND FUNCTIONS

LCR

RC RR

LFE

VIRTUAL

DSP

PCM

MATRIX

SILENT

DIGITAL

MUTE

SLEEP

STEREO

TUNED

MEMORY

AUTO

PRO LOGIC

VOLUME

DTS

MOVIE

THTR

ENTERTAINMENT

DOLBY DIGITAL

PRO

LOGIC

VCR

V-AUX

DVD

TUNER CD

TV/CBL

MD/CD

VCR2/DVR

1234

57890qwert

1 Processor indicators

Lights up when the t, g, VIRTUAL,

PRO LOGIC

DSP

are activated.

MATRIX lights up when the Dolby Digital EX decoder or

the DTS-ES compatible decoder is activated.

2 Input source indicator

Shows the current input source with a cursor.

3 MUTE indicator

Flashes while the MUTE function is on.

4 VOLUME level indicator

Indicates the volume level.

5 v indicator

Lights up when this unit is reproducing PCM (pulse code

modulation) digital audio signals.

6 SILENT indicator

Lights up when headphones are connected while the

digital sound field processor is on.

7 Headphones indicator

Lights up when headphones are connected.

8 DSP program indicators

The name of the selected DSP program lights up when the

ENTERTAINMENT, MOVIE THEATER 1, MOVIE

THEATER 2 or V/DTS SURROUND DSP program is

selected.

9 Multi-information display

Shows the current DSP program name and other

information when adjusting or changing settings.

0 STEREO indicator

Lights up when this unit is receiving a strong signal for an

FM stereo broadcast while the “AUTO” indicator is lit.

q TUNED indicator

Lights up when this unit is tuned to a station.

w MEMORY indicator

Flashes to show a station can be stored.

e AUTO indicator

Shows that this unit is in the automatic tuning mode.

r SLEEP indicator

Lights up while the sleep timer is on.

t Input channel indicator

Indicates the channel components of input signals being

received.

Front panel display

0102V630_1-8_EN(U) 12/27/01, 7:45 PM8

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SPEAKER SETUP

Speakers

This unit has been designed to provide the best sound-

field quality with a 6-speaker system, using main left and

right speakers, rear left and right speakers, a center

speaker, and a rear center speaker. If you use different

brands of speakers (with different tonal qualities) in your

system, the tone of a moving human voice and other types

of sound may not shift smoothly. We recommend that you

use speakers from the same manufacturer or speakers

with the same tonal quality.

The main speakers are used for the main source sound

plus effect sounds. They will probably be the speakers

from your present stereo system. The rear speakers are

used for effect and surround sounds. The center speaker is

for the center sounds (dialog, vocals, etc.). The rear center

speaker supplements the rear (left and right) speakers and

provides for more realistic front-to-back transitions.

The main speakers should be high-performance models

and have enough power-handling capacity to accept the

maximum output of your audio system. The other

speakers do not have to be equal to the main speakers. For

precise sound localization, however, it is ideal to use the

models of equivalent performance with the main

speakers.

■ Use of a subwoofer expands your

sound field

It is also possible to further expand your system with the

addition of a subwoofer. The use of a subwoofer is

effective not only for reinforcing bass frequencies from

any or all channels, but also for reproducing the LFE

(low-frequency effect) channel with high fidelity when

playing back Dolby Digital or DTS signals. The

YAMAHA Active Servo Processing Subwoofer System is

ideal for natural and lively bass reproduction.

PREPARATION

Speaker placement

Refer to the following diagram when you place the

speakers.

■ Main speakers

Place the main left and right speakers an equal distance

from the ideal listening position. The distance between

each speaker and each side of the video monitor should

also be the same.

■ Center speaker

Align the front face of the center speaker with the front

face of your video monitor. Place the speaker as close to

the monitor as possible (such as directly over or under the

monitor) and centrally between the main speakers.

■ Rear speakers

Place these speakers behind your listening position,

facing slightly inwards, nearly 1.8 m (6 feet) above the

floor.

■ Rear center speaker

Place the rear center speaker in the center between the

rear left and right speakers at the same height from the

floor as the rear speakers.

■ Subwoofer

The position of the subwoofer is not so critical, because

low bass sounds are not highly directional. But it is better

to place the subwoofer near the main speakers. Turn it

slightly toward the center of the room to reduce wall

reflections.

Note

• If you do not use any of effect speakers (rear, center and/or rear

center), change the settings of SPEAKER SET items at the

SET MENU to designate the signals to other terminals you

connect speakers to.

CAUTION

Use magnetically shielded speakers. If this type of

speakers still creates the interference with the monitor,

place the speakers away from the monitor.

Main

speaker (L)

1.8 m (6 feet)

Rear speaker (L)

Rear center

speaker

Rear speaker (R)

Subwoofer

Main speaker (R)Center speaker

0103V630_9-18_EN(U) 12/27/01, 7:45 PM9

SPEAKER SETUP

Connecting the speakers

Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are

faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound

will be unnatural and lack bass.

CAUTION

• Use speakers with the specified impedance shown on the rear panel of this unit.

• Do not let the bare speaker wires touch each other or any metal part of this unit. This could damage this unit

and/or the speakers.

If necessary, use the SET MENU to change the speaker mode settings according to the number and size of the speakers

in your configuration after you finish connecting your speakers.

■ Speaker cables

A speaker cord is actually a pair of insulated cables

running side by side. One cable is colored or shaped

differently, perhaps with a stripe, groove or ridge.

1 Remove approximately 10 mm (3/8”) of

insulation from each of the speaker cables.

2 Twist the exposed wires of the cable

together to prevent short circuits.

■ Connecting to the SPEAKERS terminals

1 Unscrew the knob.

2 Insert one bare wire into the hole in the side

of each terminal.

3 Tighten the knob to secure the wire.

(U.S.A., Canada, Australia, China, Korea and General models)

• Banana plug connections are also possible. First, tighten the

knob and then insert the banana plug connector into the end of

the corresponding terminal.

10 mm (3/8”)

■ MAIN SPEAKERS terminals

One or two speaker systems can be connected to these terminals. When using only one speaker system, it can be

connected to either the MAIN A or the MAIN B terminals.

■ REAR SPEAKERS terminals

A rear speaker system can be connected to these terminals.

■ CENTER SPEAKER terminals

A center speaker can be connected to these terminals.

■ REAR CENTER SPEAKER terminals

A rear center speaker can be connected to these terminals.

Red: positive (+)

Black: negative (–)

Banana plug

(U.S.A. model)

0103V630_9-18_EN(U) 12/27/01, 7:45 PM10

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SPEAKER SETUP

DIGITAL

OUTPUT

SPEAKERS

MAIN

DIGITAL

INPUT

6CH INPUT

(PLAY)

OUT

(REC)

DVD

D-TV

/CBL

DVD

OUT

VCR 1

VCR 2

/VDR

/CD-R

D-TV

/CBL

OUT

DVD

ANT

GND

UNBAL.

OPTICAL

D-TV/CBL

MD/CD-R

OPTICAL

COAXIAL

S VIDEO VIDEO

OUTPUT

S VIDEO

MONITOR OUT

MONITOR

OUT

VIDEO

TUNER

COMPONENT VIDEO

AUDIOAUDIO

MAIN

CENTER

SUB

WOOFER

SUB

WOOFER

SURROUND

CENTER

AC OUTLETS

REAR

CENTER

REAR CENTER

OUTPUT

–

REAR

(SURROUND)

REAR

(SURROUND)

IMPEDANCE SELECTOR

SET BEFORE POWER ON

MIN. /SPEAKER

MAIN

A OR B

A+B

CENTER

REAR CENTER

REAR

MAIN A OR B

A+B

CENTER

REAR CENTER

REAR

Subwoofer

system

Rear center

speaker

Main B speaker

Center

speaker

Right

Rear speaker

■ SUBWOOFER jack

When using a subwoofer with built-in amplifier, including the YAMAHA Active Servo Processing Subwoofer System,

connect the input jack of the subwoofer system to this jack. Low bass signals distributed from the main, center and/or

rear channels are directed to this jack in accordance with your SPEAKER SET selections. The LFE (low-frequency

effect) signals generated when Dolby Digital or DTS is decoded are also directed to this jack in accordance with your

SPEAKER SET selections.

Notes

• The cut-off frequency of the SUBWOOFER jack is 90 Hz.

• If you do not use a subwoofer, designate the signals to the main left and right speakers by changing the setting of SPEAKER SET

item “1E BASS” on the SET MENU to MAIN.

• Use the control on the subwoofer to adjust its volume level. It is also possible to adjust the volume level by using this unit’s remote

control (see “ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS” on page 49).

Right Left

Main A speaker

Right Left

Left

The diagram shows the speaker layout in the listening

room.

0103V630_9-18_EN(U) 12/27/01, 7:45 PM11

SPEAKER SETUP

SPEAKERS

MAIN

MPONENT VIDEO

CENTER

REAR

CENTER

REAR CENTER

OUTPUT

–

REAR

(SURROUND)

REAR

(SURROUND)

MIN. /SPEAKER

MAIN

A OR B

A+B

CENTER

REAR CENTER

REAR

MAIN A OR B

A+B

CENTER

REAR CENTER

REAR

IMPEDANCE SELECTOR

SET BEFORE POWER ON

MIN. /SPEAKER

MAIN

A OR B

A+B

CENTER

REAR CENTER

REAR

MAIN A OR B

A+B

CENTER

REAR CENTER

REAR

IMPEDANCE SELECTOR

SET BEFORE POWER ON

Switch

position

Left

Right

Speaker

Main

Center

Rear

Center

Rear

Main

Center

Rear

Center

Rear

Impedance level

If you use one set of main speakers,

the impedance of each speaker must

be 4 Ω or higher.

If you use two sets of main speakers,

the impedance of each speaker must

be 8 Ω or higher.

The impedance must be 6 Ω or

higher.

The impedance must be 6 Ω or

higher.

The impedance of each speaker must

be 6 Ω or higher.

If you use one set of main speakers,

the impedance of each speaker must

be 8 Ω or higher.

If you use two sets of main speakers,

the impedance of each speaker must

be 16 Ω or higher.

[Canada model only]

The impedance of each speaker must

be 8 Ω or higher.

The impedance must be 8 Ω or

higher.

The impedance must be 8 Ω or

higher.

The impedance of each speaker must

be 8 Ω or higher.

IMPEDANCE

SELECTOR

switch

(U.S.A. model)

■ IMPEDANCE SELECTOR switch

WARNING

Do not change setting of the IMPEDANCE SELECTOR switch when the power of this unit is on, this may damage

the unit. If this unit fails to turn on when STANDBY/ON (or SYSTEM POWER) is pressed, the IMPEDANCE

SELECTOR switch may not be fully slid to either position. If so, slide the switch all the way to either position when

this unit is in the standby mode.

Select the switch position (left or right) according to the impedance of the speakers in your system. Be sure to move this

switch only when this unit is in the standby mode.

0103V630_9-18_EN(U) 12/27/01, 7:45 PM12

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONNECTIONS

Before connecting components

CAUTION

Do not connect this unit or other components to the

mains power until all connections between the

components have been completed.

• Be sure all connections are made correctly, that is to

say L (left) to L, R (right) to R, “+” to “+” and “–” to

“–”. Some components require different connection

methods and have different jack names. Refer to the

operation instructions for each component to be

connected to this unit.

• When you connect other YAMAHA audio components

(such as a tape deck, MD recorder and CD player or

changer), connect them to the jack with the same

number labels as !, #, $ etc. YAMAHA applies this

labeling system to all its products.

• After you have completed all connections, check them

again to make sure they are correct.

• The name of jack corresponds to input selector.

■ Connecting to digital jacks

This unit has digital jacks for direct transmission of

digital signals through either coaxial or fiber optic cables.

You can use the digital jacks to input PCM, Dolby Digital

and DTS bitstreams. To enjoy multi-channel sound track

of DVD software, etc. with DSP effect, you need to make

digital connection. All digital input jacks are acceptable

for 96-kHz sampling digital signals.

Note

• The OPTICAL jacks on this unit conform to the EIA standard.

If you use a fiber optic cable that does not conform to this

standard, this unit may not function properly.

DIGITAL

OUTPUT

SPEAKERS

MAIN

DIGITAL

INPUT

6CH INPUT

(PLAY)

OUT

(REC)

DVD

D-TV

/CBL

DVD

OUT

VCR 1

VCR 2

/VDR

/CD-R

D-TV

/CBL

DVD

OUT

ANT

GND

UNBAL.

OPTICAL

D-TV/CBL

MD/CD-R

OPTICAL

COAXIAL

S VIDEO VIDEO

OUTPUT

S VIDEO

MONITOR OUT

MONITOR

OUT

VIDEO

TUNER

COMPONENT VIDEO

AUDIOAUDIO

MAIN

CENTER

SUB

WOOFER

SUB

WOOFER

SURROUND

CENTER

REAR

CENTER

REAR CENTER

OUTPUT

–

REAR

(SURROUND)

REAR

(SURROUND)

AC OUTLETS

(page 19)

6CH INPUT jacks

(page 18)

DIGITAL OUTPUT jack

(page 16)

OUTPUT jacks

(page 18)

DIGITAL INPUT jacks

(pages 13-16)

Antenna input terminals

(page 17)

Speaker terminals

(pages 10-11)

Video component jacks

(pages 14-15)

Audio component jacks

(page 16)

SUBWOOFER

OUTPUT jack

(page 11)

0103V630_9-18_EN(U) 12/27/01, 7:45 PM13

CONNECTIONS

Connecting video components

Refer to the connection examples on the next page.

■ Types of video jacks

There are three types of video jacks as follows:

1 VIDEO jack

Conventional composite video signal.

2 S VIDEO jack

Transmits color and luminance separately and achives

high-quality color reproduction.

3 COMPONENT VIDEO jacks

Transmit color difference (P

, P

) and

luminance separately and provide the best quality

picture.

• Each type of video jack works independently. Signals

input through the composite video, S-video and

component jacks are only output through the

corresponding composite video, S-video, and

component jacks.

• Use a commercially available cable specified for

connecting each type of jacks.

• The description of the component video jacks may

differ depending on the component (e.g. Y, C

, C

/Y,

, P

/Y, B-Y, R-Y etc.). When using these jacks, refer

also to the operation instructions for the component

being connected.

■ Connecting a video monitor

Connect the video input jack on your video monitor to the

MONITOR OUT VIDEO jack.

Note

• If you connect this unit with a source component using S-video

(or Component video) jacks, you also need to connect your

video monitor using S-video (or Component video) jacks.

■ Connecting a DVD player/digital

TV/cable TV

Connect the optical digital audio signal output jack on

your component to the DIGITAL INPUT jack and

connect the video signal output jack on the component to

the VIDEO jack on this unit.

Then connect AUDIO jacks on your component to the

AUDIO jacks on this unit.

• If your video component has an S-video output or component

video output, connect the S-video signal output jack on the

component to the S VIDEO jack or connect the component

video signal output jacks on the component to the

COMPONENT VIDEO jacks.

• The AUDIO jacks are available for a video component which

does not have optical digital output jack. However, multi-

channel reproduction cannot be obtained with audio signals

input from AUDIO jacks.

■ Connecting a game console or

camcorder

Connect the optical digital audio signal output jack on

your video component to the OPTICAL jack on the front

panel and connect video signal output jack on the

component to the VIDEO jack on the front panel.

• If your video component has an S-video output, connect the S-

video signal output jack on the component to the S VIDEO

jack.

• The AUDIO jacks are available for a video component such as

a camcorder which does not have optical digital output jack.

■ Connecting a VCR or DVR (digital

video recorder)

Connect the audio signal input jacks on your video

component to the AUDIO OUT jacks and connect the

video signal input jack on the video component to the

VIDEO OUT jack on this unit for picture recording.

Connect the audio signal output jacks on your component

to the AUDIO IN jacks and connect the video signal

output jack on the component to the VIDEO IN jack on

this unit to play a source from your recording component.

Second VCR or digital video recorder can be connected

using VCR 2/DVR jacks.

• If your video component has an S-video input, connect the S-

video signal input jack on the component to the S VIDEO OUT

jack.

• If your video component has an S-video output, connect the S-

video signal output jack on the component to the S VIDEO IN

jack.

Notes

• Once you have connected a recording component to this unit,

keep its power turned on while using this unit. If the power is

off, this unit may distort the sound from other components.

• S-video and component video signals pass independently

through this unit’s video circuit. Make sure to connect this unit

to both a source component and a recording component using

the video jacks of the same system.

COMPONENT VIDEO

VIDEOS VIDEO

2 1 3

0103V630_9-18_EN(U) 12/27/01, 7:45 PM14

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONNECTIONS

DIGITAL

OUTPUT

DIGITAL

INPUT

6CH INPUT

(PLAY)

OUT

(REC)

DVD

D-TV

/CBL

DVD

OUT

VCR 1

VCR 2

/VDR

/CD-R

D-TV

/CBL

OUT

ANT

GND

UNBAL.

OPTICAL

D-TV/CBL

MD/CD-R

OPTICAL

COAXIAL

S VIDEO VIDEO

OUTPUT

S VIDEO

MONITOR OUT

MONITOR

OUT

VIDEO

TUNER

B/CBPR/CR

COMPONENT VIDEO

AUDIOAUDIO

MAIN

CENTER

SUB

WOOFER

SUB

WOOFER

SURROUND

MIN. /SPEAKER

MAIN

A OR B

A+B

CENTER

REAR CENTER

REAR

A/B/C/D/E

BASS

– + – +

TREBLE

VIDEO AUX

S VIDEO VIDEO AUDIO OPTICALLR

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

VOLUME

INPUT

INPUT M0DE

6CH INPUT

V V

AUDIO

OUTPUT

AUDIO

INPUT

VIDEO

OUTPUT

VIDEO

INPUT

VIDEO

INPUT

VIDEO

OUTPUT

OPTICAL

OUTPUT

AUDIO

OUTPUT

VIDEO

OUTPUT

OPTICAL

OUTPUT

OPTICAL

OUTPUT

VIDEO

OUTPUT

indicates video cables

indicates optical cables

indicates right analog cables

indicates left analog cables

indicates signal direction

Video monitor

VCR 1

DVD player

TV/digital TV/

cable TV

Game console or

camcorder

0103V630_9-18_EN(U) 12/27/01, 7:45 PM15

CONNECTIONS

Connecting audio components

■ Connecting a CD player

Connect the coaxial digital output jack on your CD player

to the DIGITAL INPUT CD jack.

• The AUDIO jacks are available for a CD player which does not

have coaxial digital output jack.

■ Connecting a CD recorder or MD

recorder

Connect the optical digital signal input jack on your CD

recorder or MD recorder to the DIGITAL OUTPUT MD/

CD-R jack for digital recording.

Connect the optical digital output jack on your CD

recorder or MD recorder to the DIGITAL INPUT MD/

CD-R jack to play a source from your recording

component.

DIGITAL

OUTPUT

DIGITAL

INPUT

6CH INPUT

(PLAY)

OUT

(REC)

DVD

OUT

VCR 1

VCR 2

/VDR

/CD-R

D-TV

/CBL

OUT

OPTICAL

D-TV/CBL

MD/CD-R

OPTICAL

COAXIAL

S VIDEO VIDEO

OUTPUT

S VIDEO

MONITOR OUT

VIDEO

VIDEOAUDIO

MAIN

CENTER

SUB

WOOFER

SUB

WOOFER

SURROUND

AUDIO

OPTICAL

INPUT

OPTICAL

OUTPUT

COAXIAL

OUTPUT

indicates signal direction

CD player

CD recorder or

MD recorder

• The AUDIO jacks are available for an CD recorder or MD

recorder which does not have optical digital input or output

jack.

Notes

• Once you have connected a recording component to this unit,

keep its power turned on while using this unit. If the power is

off, this unit may distort the sound from other components.

• DIGITAL OUTPUT jack and analog OUT (REC) jacks are

independent. Only digital signals are output from DIGITAL

OUTPUT jack and analog signals from OUT (REC) jacks.

indicates optical cables

indicates coaxial cables

0103V630_9-18_EN(U) 12/27/01, 7:45 PM16

Pagina se încarcă ...

Yamaha RX-V630 Manual de utilizare

Marca: Yamaha

Model: RX-V630

Categorie: Receptoare AV

Tip: Manual de utilizare

Descărcați PDF

raport

în alte limbi

Türkçe: Yamaha RX-V630 Kullanım kılavuzu
français: Yamaha RX-V630 Manuel utilisateur
čeština: Yamaha RX-V630 Uživatelský manuál
русский: Yamaha RX-V630 Руководство пользователя
English: Yamaha RX-V630 User manual
suomi: Yamaha RX-V630 Ohjekirja
polski: Yamaha RX-V630 Instrukcja obsługi
Deutsch: Yamaha RX-V630 Benutzerhandbuch
italiano: Yamaha RX-V630 Manuale utente
español: Yamaha RX-V630 Manual de usuario
svenska: Yamaha RX-V630 Användarmanual
dansk: Yamaha RX-V630 Brugermanual
português: Yamaha RX-V630 Manual do usuário
Nederlands: Yamaha RX-V630 Handleiding

Yamaha RX-V630 Manual de utilizare

Yamaha RX-V630 Manual de utilizare

în alte limbi

Lucrări conexe