Tesla WD630M Manual de utilizare

Product images are for illustrative purposes only and may differ from the actual product.

DISHWASHER

WD630M

User Manual

SRB

HR RO SLOENG

BiH/

CG

DISHWASHER

PART I: GENERIC VERSION

User Manual

Please read this manual carefully before using the dishwasher and

Keep this manual for future reference.

4

ENG

SAFETY INFORMATION

WARNING!

When using your dishwasher, follow the precautions

listed below:

• Installation and repair can only be carried out by a

qualiﬁed technician

• This appliance is intended to be used in household

and similar applications such as:

– staff kitchen areas in shops, ofﬁces and other

working environments;

– farm houses;

– by clients in hotels, motels and other residential

type environments;

– bed and breakfast type environments.

• This appliance can be used by children aged from 8

years and above and persons with reduced physical,

sensory or mental capabilities or lack of experience

and knowledge if they have been given supervision

or instruction concerning use of the appliance in a

safe way and understand the hazards involved.

• Children should not play with the appliance.

Cleaning and user maintenance should not be done

by children without supervision. (For EN60335-1)

• This appliance is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience

and knowledge, unless they have been given

supervision or instruction concerning use of the

appliance by a person responsible for their safety.

(For IEC60335-1)

• Packaging material could be dangerous for children!

• This appliance is for indoor household use only.

• To protect against the risk of electrical shock, do

not immerse the unit, cord or plug in water or other

liquids.

• Please unplug before cleaning and performing

maintenance on the appliance.

• Use a soft cloth moistened with mild soap, and then

use a dry cloth to wipe it again.

Grounding Instructions

• This appliance must be grounded. In the event of a

malfunction or breakdown, grounding will reduce

the risk of an electric shock by providing a path of

least resistance for the electric current. This appliance

is equipped with a grounding conductor plug.

• The plug must be plugged into an appropriate

outlet that is installed and grounded in accordance

with all local codes and ordinances.

• Improper connection of the grounding conductor

can result in the risk of an electric shock.

• Check with a qualiﬁed electrician or service

representative if you are in doubt whether the

appliance is properly grounded.

• Do not modify the plug provided with the

appliance; If it does not ﬁt the outlet.

• Have a proper outlet installed by a qualiﬁed

electrician.

• Do not abuse, sit on, or stand on the door or dish

rack of the dishwasher.

• Do not operate your dishwasher unless all enclosure

panels are properly in place.

• Open the door very carefully if the dishwasher is

operating, there is a risk of water squirting out.

• Do not place any heavy objects on, or stand on

the door when it is open. The appliance could tip

forward.

• When loading items to be washed:

1. Locate sharp items so that they are not likely to

damage the door seal;

2. Warning: Knives and other utensils with sharp

points must be loaded in the basket with their

points facing down or placed in a horizontal

position.

• Some dishwasher detergents are strongly alkaline.

They can be extremely dangerous if swallowed.

Avoid contact with the skin and eyes and keep

children away from the dishwasher when the door

is open.

• Check that the detergent powder case is empty

after completion of the wash cycle.

• Do not wash plastic items unless they are marked

“dishwasher safe” or equivalent.

• For unmarked plastic items not so marked, check

the manufacturer's recommendations.

• Use only detergents and rinse agents

recommended for use in an automatic dishwasher.

• Never use soap, laundry detergent, or hand washing

detergent in your dishwasher.

• The door should not be left open, since this could

increase the risk of tripping.

• If the supply cord is damaged, it must be replaced

by the manufacturer or its service agent or a similarly

qualiﬁed person in order to avoid a hazard.

• During installation, the power supply must not be

excessively or dangerously bent or ﬂattened.

• Do not tamper with controls.

• The appliance needs to be connected to the main

water valve using new hose sets. Old sets should not

be reused.

• To save energy, in standby mode, the appliance will

switch off automatically when there is no operation

for 30 minutes.

Disposal

• For disposing of packaging and the appliance

please go to a recycling center. Cut off the power

supply cable and make the door closing device

unusable.

• Cardboard packaging is manufactured from

recycled paper and should be disposed of in a

paper waste collection bin for recycling.

• By ensuring this product is disposed of correctly, you

will help prevent potential negative consequences

for the environment and human health, which

5

ENG

could otherwise be caused by inappropriate waste

handling of this product.

• For more detailed information about recycling of

this product, please contact your local city ofﬁce and

your household waste disposal service.

• DISPOSAL: Do not dispose this product as

unsorted municipal waste. Collection of such waste

separately for special treatment is necessary.

PRODUCT OVERVIEW

IMPORTANT

To get the best performance from your dishwasher, read all operating instructions before using it for the ﬁrst time.

NOTE

Pictures are only for reference; different models may be different.

Dispenser

Salt container

Inner pipe

Lower spray arm

Filter assembly

Cutlery basket Upper basket

Cup rack Upper spray arm

Lower basket

6

ENG

USING YOUR DISHWASHER

Before using your dishwasher:

NOTE

If your model does not have any water softener compartment, you may skip this section. Always use salt that

is intended for dishwasher use. The salt container is located beneath the lower basket and should be ﬁlled as

explained in the following:

WARNING!

• Only use salt speciﬁcally designed for dishwashers use!

Every other type of salt not speciﬁcally designed for dishwasher use, especially table salt, will damage the water

softener compartment. In case of damages caused by the use of unsuitable salt the manufacturer does not give

any warranty nor is liable for any damages caused.

• Only ﬁll with salt before running a cycle.

This will prevent any grains of salt or salty water, which may have been spilled, remaining on the bottom of the

machine for any period of time, which may cause corrosion.

Please follow the steps below for adding dishwasher salt:

1. Remove the lower basket and unscrew the reservoir

cap.

2. Place the end of the funnel (supplied) into the hole

and pour in about 1.5kg of dishwasher salt.

3. Fill the salt container to its maximum limit with water,

it is normal for a small amount of water to come out

of the salt container.

4. After ﬁlling the container, screw back the cap tightly.

5. The salt warning light will stop shining after the salt

container has been ﬁlled with salt.

6. Immediately after ﬁlling the salt into the salt

container, a washing program should be started

(We suggest using a short program). Otherwise the

ﬁlter system, pump or other important parts of the

machine may be damaged by salty water. This is

void of warranty.

1. Set the water softener

2. Loading salt into the softener compartment

3. Loading the basket

4. Filling the dispenser

Loading The Salt Into The Softener

Inside Outside

NOTE

Please check the section 1 “Water Softener” of PART II: Special Version, If you need to set the water softener .

7

ENG

NOTE

• The salt container must only be reﬁlled when the salt warning light ( ) in the control panel comes on.

Depending on how well the salt dissolves, the salt warning light may still be on even though the salt container is

ﬁlled.

If there is no salt warning light in the control panel (for some Models), you can estimate when to ﬁll the salt into

the softener by the cycles that the dishwasher has run.

• If salt has spilled, run a soak or quick program to remove it.

Basket - user tips

Adjusting the upper basket

Type 1:

The height of the upper basket can be easily adjusted to accommodate taller dishes in either the upper or lower

basket.

To adjust the height of the upper rack, follow these steps:

Pull out upper basket. Remove upper basket.

Lower position

Upper position

Re-attach upper basket to the upper or lower rollers.

To raise the upper basket, just lift the upper basket

at the center of each side until the basket locks into

place in the upper position. It is not necessary to lift the

adjuster handle.

Push in upper basket.

To lower the upper basket, lift the adjust handles on

each side to release the basket and lower it to the lower

position.

Type 2:

8

ENG

Folding back the cup shelves

To make room for taller items in the upper basket, raise the cup rack upwards. You can then lean the tall glasses

against it. You can also remove it when it is not required for use.

Folding back the rack shelves

The spikes are used for holding plates and a platter. They can be lowered to make more room for large items.

MAINTENANCE AND CLEANING

External Care

The door and door seal

Clean the door seals regularly with a soft damp cloth to remove food deposits. When the dishwasher is being

loaded, food and drink residues may drip onto the sides of the dishwasher door. These surfaces are outside the

wash cabinet and are not accessed by water from the spray arms. Any deposits should be wiped off before the

door is closed.

The control panel

If cleaning is required, the control panel should be wiped with a soft damp cloth ONLY.

WARNING!

• To avoid penetration of water into the door lock and electrical components, do not use a spray cleaner of any

kind.

• Never use abrasive cleaners or scouring pads on the outer surfaces because they may scratch the ﬁnish. Some

paper towels may also scratch or leave marks on the surface.

Internal Care

Filtering system

The ﬁltering system in the base of the wash cabinet retains coarse debris from the washing cycle. The collected

coarse debris may cause the ﬁlters to clog. Check the condition of the ﬁlters regularly and clean them if necessary

under running water. Follow the steps below to clean the ﬁlters in the wash cabinet.

Raise upwards Fold backwards

9

ENG

NOTE

Pictures are only for reference, different models of the ﬁltering system and spray arms may be different. Please

prevail in kind.

Main ﬁlter

Hold the coarse ﬁlter and rotate it counterclockwise to

unlock the ﬁlter. Lift the ﬁlter upwards and out of the

dishwasher.

Larger food remnants can be cleaned by rinsing the

ﬁlter under running water. For a more thorough clean,

use a soft cleaning brush.

The ﬁne ﬁlter can be pulled off the bottom of the ﬁlter

assembly. The coarse ﬁlter can be detached from the

main ﬁlter by gently squeezing the tabs at the top and

pulling it away.

Reassemble the ﬁlters in the reverse order of the

disassembly, replace the ﬁlter insert, and rotate

clockwise to the close arrow.

To remove the upper spray arm, hold the nut in the

center still and rotate the spray arm counterclockwise

to remove it.

Open

Coarse ﬁlter

Main ﬁlter

Fine ﬁlter

WARNING!

• Do not over tighten the ﬁlters. Put the ﬁlters back

in sequence securely, otherwise coarse debris

could get into the system and cause a blockage.

• NEVER use the dishwasher without ﬁlters in

place. Improper replacement of the ﬁlter may

reduce the performance level of the appliance

and damage dishes and utensils.

Spray arms

It is necessary to clean the spray arms regularly for

hard spray arm jets and bearings.

To clean the spray arms, follow the instructions:

10

ENG

Caring For The Dishwasher

Frost precaution

Please take frost protection measures on the dishwasher in winter. After every washing cycles, please operate as

follows:

1. Cut off the electrical power to the dishwasher at the power source.

2. Turn off the water supply and disconnect the water inlet pipe from the water valve.

3. Drain the water from the inlet pipe and water valve. (Use a pan to gather the water)

4. Reconnect the water inlet pipe to the water valve.

5. Remove the ﬁlter at the bottom of the tub and use a sponge to soak up water in the sump.

After every wash

After every wash, turn off the water supply to the appliance and leave the door slightly open so that moisture and

odours are not trapped inside.

Remove the plug

Before cleaning or performing maintenance, always remove the plug from the socket.

No solvents or abrasive cleaning

To clean the exterior and rubber parts of the dishwasher, do not use solvents or abrasive cleaning products. Only

use a cloth with warm soapy water.

To remove spots or stains from the surface of the interior, use a cloth dampened with water and a little vinegar, or a

cleaning product made speciﬁcally for dishwashers.

When not in use for a longtime

It is recommended that you run a wash cycle with the dishwasher empty and then remove the plug from the

socket, turn off the water supply and leave the door of the appliance slightly open. This will help the door seals to

last longer and prevent odours from forming within the appliance.

Moving the appliance

If the appliance must be moved, try to keep it in the vertical position. If absolutely necessary, it can be positioned

on its back.

Seals

One of the factors that cause odours to form in the dishwasher is food that remains trapped in the seals. Periodic

cleaning with a damp sponge will prevent this from occurring.

To remove the lower spray arm, pull out the spray arm

upward.

Wash the arms in soapy and warm water and use a

soft brush to clean the jets. Replace them after rinsing

them thoroughly.

11

ENG

INSTALLATION INSTRUCTION

About Power Connection

Safety supply hose

Ordinary supply hose

WARNING!

Electrical Shock Hazard

Disconnect electrical power before installing dishwasher.

Failure to do so could result in death or electrical shock.

For personal safety:

• Do not use an extension cord or an adapter plug with this appliance.

• Do not, under any circumstances, cut or remove the grounding connection from the power cord.

Electrical requirements

Please look at the rating label to know the rating voltage and connect the dishwasher to the appropriate power

supply. Use the required fuse 10A/13A/16A, time delay fuse or circuit breaker recommended and provide

separate circuit serving only this appliance.

Electrical connection

Ensure the voltage and frequency of the power being corresponds to those on the rating plate. Only insert the

plug into an electrical socket which is grounded properly. If the electrical socket to which the appliance must be

connected is not appropriate for the plug, replace the socket, rather than using a adaptors or the like as they could

cause overheating and burns.

Ensure that proper grounding exists before use.

Water Supply and Drain

Cold water connection

Connect the cold water supply hose to a threaded

3/4(inch) connector and make sure that it is fastened

tightly in place.

If the water pipes are new or have not been used for

an extended period of time, let the water run to make

sure that the water is clear. This precaution is needed

to avoid the risk of the water inlet to be blocked and

damage the appliance.

About the safety supply hose

The safety supply hose consists of double walls. The hose’s system guarantees its intervention by blocking the ﬂow

of water in case of the supply hose breaking and when the air space between the supply hose itself and the outer

corrugated hose is full of water.

A hose that attaches to a sink spray can burst if it is installed on the same water line as the dishwasher. If your sink

has one, it is recommended that the hose be disconnected and the hole plugged.

ATTENTION!

The installation of the pipes and electrical equipments should be done by professionals.

12

ENG

How to drain excess water from hoses

If the sink is 1000 higher from the ﬂoor, the excess water in hoses cannot be drained directly into the sink. It will be

necessary to drain excess water from hoses into a bowl or suitable container that is held outside and lower than the

sink.

Water outlet

Connect the water drain hose. The drain hose must be correctly ﬁtted to avoid water leaks. Ensure that the water

drain hose is not kinked or squashed.

Extension hose

If you need a drain hose extension, make sure to use a similar drain hose.

It must be no longer than 4 meters; otherwise the cleaning effect of the dishwasher could be reduced.

Syphon connection

The waste connection must be at a height less than 100 cm (maximum) from the bottom of the dish. The water

drain hose should be ﬁxed .

40 mm

Back of dishwasher

Drain hose

Counter

Water Inlet

Power Cable

Drain Pipe

How to connect the safety supply hose

1. Pull the safety supply hoses completely out from storage compartment located at the rear of dishwasher.

2. Tighter the screws of the safety supply hose to the faucet with thread 3/4inch.

3. Turn water fully on before starting the dishwasher.

How to disconnect the safety supply hose

1. Turn off the water.

2. Unscrew the safety supply hose from the faucet.

Connection of Drain Hoses

Insert the drain hose into a drain pipe with a minimum diameter of 4 cm, or let it run into the sink, making sure to

avoid bending or crimping it. The height of drain pipe must be less than 1000mm. The free end of the hose must

not be immersed in water to avoid the back ﬂow of it.

Please securely ﬁx the drain hose in either position A or position B

13

ENG

Position The Appliance

Position the appliance in the desired location. The back should rest against the wall behind it, and the sides,

along the adjacent cabinets or walls. The dishwasher is equipped with water supply and drain hoses that can be

positioned either to the right or the left sides to facilitate proper installation.

Levelling the appliance

Once the appliance is positioned for levelling, the height

of the dishwasher may be altered via adjustment of the

screwing level of the feet.

In any case,the appliance should not be inclined

more than 2°.

NOTE

Only apply to the free standing dishwasher.

Free Standing Installation

Fitting between existing cabinets

The height of the dishwasher, 845 mm, has been designed

in order to allow the machine to be ﬁtted between existing

cabinets of the same height in modern ﬁtted kitchens. The

feet can be adjusted so that correct height is reached.

The laminated top of the machine does not require any

particular care since it is heatproof, scratchproof and

stainproof.

Underneath existing work top

(When ﬁtting beneath a work top)

In most modern ﬁtted kitchens there is only one single

work top under which cabinets and electrical appliances

are ﬁtted. In this case remove the work top of the

dishwasher by unscrewing the screws under the rear edge

of the top (a).

ATTENTION!

After removing the work top, the screws must be screwed

again under the rear edge of the top (b).

The height will then be reduced to 815 mm, as scheduled

by the International Regulations (ISO) and the dishwasher

will ﬁt perfectly under the kitchen working top.

Built-In Installation (for the integrated model)

Step 1. Selecting the best location for the dishwasher

The installation position of dishwasher should be near the existing inlet and drain hoses and power cord.

Illustrations of cabinet dimensions and installation position of the dishwasher.

1. Less than 5 mm between the top of dishwasher and cabinet and the outer door aligned to cabinet.

14

ENG

Electrical, drain

and water supply

line entrances

Space between cabinet

bottom and ﬂoor

600 mm (for 60 cm model)

450 mm (for 45 cm model)

2. If dishwasher is in stalled at the corner of the cabinet,

there should be some space when the door is opened.

NOTE

Depending on where your electrical outlet is, you may need

to cut a hole in the opposite cabinet side.

CabinetDishwasher

Door of

dishwasher

Minimum space

of 50mm

Step 2. Aesthetic panel’s dimensions and installation

Magical paster

1. Take away the four short screws

2. Pin up the four long screws

Magical paster

NOTE

The aesthetic wooden panel could be processed according to the installation drawings.

Semi-integrated model

• Magical paster A and magical paster B be disjoinedon ,magical paster A on the aesthetic wooden panel and

felted magical paster B of the outer door of dishwasher (see ﬁgure A). After positioning of the panel , ﬁx the

panel onto the outer door by screws and bolts (See ﬁgure B).

15

ENG

Full-integrated model

Install the hook on the aesthetic wooden panel and put the hook into the slot of the outer door of dishwasher (see

ﬁgure A). After positioning of the panel , ﬁx the panel onto the outer door by screws and bolts (See ﬁgure B).

1. Take away the four short screws

2.Pin up the four long screws

Step 3. Tension adjustment of the door

1. The door springs are set at the factory to the proper

tension for the outer door. If aesthetic wooden panel are

installed, you will have to adjust the door spring tension.

Rotate the adjusting screw to drive the adjustor to strain

or relax the steel cable.

2. Door spring tension is correct when the door remains

horizontal in the fully opened position, yet rises to a close

with the slight lift of a ﬁnger.

Step 4. Dishwasher installation steps

Please refer to the speciﬁed installation steps in the installation drawings.

NOTE

1. Afﬁx the condensation strip under the work surface of cabinet. Please ensure the condensation strip is ﬂush with

edge of work surface. (Step 2)

2. Connect the inlet hose to the cold water supply.

3. Connect the drain hose.

4. Connect the power cord.

5. Place the dishwasher into position. (Step 4)

6. Level the dishwasher. The rear food can be adjusted from the front of the dishwasher by turning the Philips

screw in the middle of the base of dishwasher use an Philips screw. To adjust the front feet, use a ﬂat screw

driver and turn the front feet until the dishwasher is level. (Step 5 to Step 6)

7. Install the furniture door to the outer door of the dishwasher. (Step 7 to Step 10)

8. Adjust the tension of the door springs by using an Allen key turning in a clockwise motion to tighten the left and

right door springs. Failure to do this could cause damage to your dishwasher. (Step 11)

9. The dishwasher must be secured in place. There are two ways to do this:

A. Normal work surface: Put the installation hook into the slot of the side plane and secure it to the work surface

with the wood screws.

B. Marble or granite work top: Fix the side with Screw.

16

ENG

Step 5. Levelling the dishwasher

Dishwasher must be level for proper dish rack operation and wash performance.

1. Place a spirit level on door and rack track inside the tub as shown to check that the dishwasher is level.

2. Level the dishwasher by adjusting the three levelling legs individually.

3. When level the dishwasher, please pay attention not to let the dishwasher tip over.

Check level

front to back

Check level

side to side

NOTE

The maximum adjustment height of the feet is 50 mm.

17

ENG

TROUBLESHOOTING TIPS

Before Calling for Service

Reviewing the charts on the following pages may save you from calling for service.

Problem Possible Causes What to Do

Dishwasher doesn’t start

Fuse blown, or the circuit break

tripped.

Replace fuse or reset circuit

breaker. Remove any other

appliances sharing the same circuit

with the dishwasher.

Power supply is not turned on.

Make sure the dishwasher is

turned on and the door is closed

securely. Make sure the power cord

is properly plugged into the wall

socket.

Water pressure is low

Check that the water supply is

connected properly and the water

is turned on.

Door of dishwasher not properly

closed.

Make sure to close the door

properly and latch it.

Water not pumped form

dishwasher

Twisted or trapped drain hose. Check the drain hose.

Filter clogged. Check coarse the ﬁlter.

Kitchen sink clogged.

Check the kitchen sink to make

sure it is draining well. If the

problem is the kitchen sink that

is not draining, you may need a

plumber rather than a serviceman

for dishwashers.

Suds in the tub

Wrong detergent.

Use only the special dishwasher

detergent to avoid suds. If this

occurs, open the dishwasher and

let suds evaporate. Add 1 gallon

of cold water to the bottom of the

dishwasher.

Close the dishwasher door, then

select any cycle. Initially, the

dishwasher will drain out the water.

Open the door after draining

stage is complete and check if the

suds have disappeared. Repeat if

necessary.

Spilled rinse-aid.

Always wipe up rinse-aid spills

immediately.

Stained tub interior

Detergent with colorant may have

been used.

Make sure that the detergent has

no colorant.

White ﬁlm on inside surface Hard water minerals.

To clean the interior, use a damp

sponge with dishwasher detergent

and wear rubber gloves. Never use

any other cleaner than dishwasher

detergent otherwise, it may cause

foaming or suds.

18

ENG

Problem Possible Causes What to Do

There are rust stains on cutlery

The affected items are not

corrosion resistant.

Avoid washing items that are

not corrosion resistant in the

dishwasher.

A program was not run after

dishwasher salt was added. Traces

of salt have gotten

into the wash cycle.

Always run a wash program

without any crockery after adding

salt. Do not select the Turbo

function (if present), after adding

dishwasher salt.

The lid of the softer is loose. Check the softener lid is secure.

Knocking noise in the dishwasher

A spray arm is knocking against an

item in a basket

Interrupt the program and

rearrange the items which are

obstructing the spray arm.

Rattling noise in the dishwasher

Items of crockery are loose in the

dishwasher.

Interrupt the program and

rearrange the items of crockery.

Knocking noise in the water pipes

This may be caused by on-site

installation or the cross-section

of the piping.

This has no inﬂuence on the

dishwasher function. If in doubt,

contact a qualiﬁed plumber.

The dishes are not clean

The dishes were not loaded

correctly.

See PART II “Preparing And

Loading Dishes”.

The program was not powerful

enough.

Select a more intensive program.

Not enough detergent was

dispensed

Use more detergent, or change

your detergent.

Items are blocking the movement

of the spray arms.

Rearrange the items so that the

spray can rotate freely.

The ﬁlter combination is not clean

or is not correctly ﬁtted in the base

of wash cabinet.

This may cause the spray arm jets

to get blocked.

Clean and ﬁt the ﬁlter correctly.

Clean the spray arm jets.

Cloudiness on glassware.

Combination of soft water and too

much detergent.

Use less detergent if you have soft

water and select a shorter cycle

to wash the glassware and to get

them clean.

White spots appear on dishes and

glasses.

Hard water area

can cause limescale deposits.

Add more detergent.

Black or grey marks on dishes

Aluminum utensils have rubbed

against dishes

Use a mild abrasive cleaner to

eliminate those marks.

Detergent left in dispenser Dishes block detergent dispenser Re-loading the dishes properly.

The dishes aren't drying

Improper loading

Load the dishwasher as suggested

in the directions.

Dishes are removed too soon

Do not empty your dishwasher

immediately after washing. Open

the door slightly so that the steam

can come out. Take out the dishes

until the inside temperature is safe

to touch. Unload the lower basket

ﬁrst to prevent the dropping water

from the upper basket.

19

ENG

Problem Possible Causes What to Do

The dishes aren't drying

Wrong program has been

selected.

With a short program, the washing

temperature is lower, decreasing

cleaning performance. Choose a

program with a long washing time.

Use of cutlery with a low-quality

coating.

Water drainage is more difﬁcult

with these items. Cutlery or dishes

of this type are not suitable for

washing in the dishwasher.

LOADING THE BASKETS ACCORDING TO

EN50242

1. Upper basket: 2. Lower basket:

Number Item

1 Cups

2 Saucers

3 Glasses

4 Small serving bowl

5 Medium serving bowl

6 Large serving bowl

Number Item

7 Dessert dishes

8 Dinner plates

9 Soup plates

10 Oval platter

11 Cutlery basket

20

ENG

3. Cutlery basket:

Number Item

1 Soup spoons

2 Forks

3 Knives

4 Teaspoons

5 Dessert spoons

6 Serving spoons

7 Serving forks

8 Gravy ladles

Information for comparability tests in

accordance with EN 50242

Capacity: 12 place settings

Position of the upper basket: lower position

Program: ECO

Rinse aid setting: 6

Softener setting: H3

Pagina se încarcă ...

Tesla WD630M Manual de utilizare

Tesla WD630M Manual de utilizare

Lucrări conexe

Alte documente