Whirlpool AVL 169 (EU) Manualul utilizatorului

Categorie
Mașini de spălat
Tip
Manualul utilizatorului
1
GB
English,1
Contents
Installation, 2-3
Unpacking and levelling, 2
Electric and water connections, 2-3
The first wash cycle, 3
Technical details, 3
Washing machine description, 4-5
Control panel, 4
Leds, 5
Starting and Programmes, 6
Briefly: how to start a programme, 6
Programme table, 6
Personalisations, 7
Setting the temperature, 7
Setting the spin cycle, 7
Functions, 7
Detergents and laundry, 8
Detergent dispenser, 8
Preparing your laundry, 8
Special items, 8
Woolmark Platinum Care, 8
Precautions and advice, 9
General safety, 9
Disposal, 9
Saving energy and respecting the environment, 9
Care and maintenance, 10
Cutting off the water or electricity supply, 10
Cleaning your appliance, 10
Cleaning the detergent dispenser, 10
Caring for your appliance door and drum, 10
Cleaning the pump, 10
Checking the water inlet hose, 10
Troubleshooting, 11
Service, 12
Before calling for Assistance, 12
WASHING MACHINE
AVL 169
Instructions for use
GB
Deutsch,13
DE
Nederlands,25
NL
Românã,37
RO
2
GB
Keep this instruction manual in a safe place for
future reference. Should the appliance be sold,
transferred or moved, make sure the instruction
manual accompanies the washing machine to inform
the new owner as to its operation and features.
Read these instructions carefully: they contain vital
information on installation, use and safety.
Unpacking and levelling
Unpacking
1. Unpack the washing machine.
2. Check whether the washing machine has been
damaged during transport. If this is the case, do not
install it and contact your retailer.
3. Remove the four
protective screws and
the rubber washer with
the respective spacer,
situated on the rear of
the appliance (see
figure).
4. Seal the gaps using the plastic plugs provided.
5. Keep all the parts: you will need them again if the
washing machine needs to be moved to another
location.
Packaging materials are not children's toys.
Levelling
1. Install the washing machine on a flat sturdy floor,
without resting it up against walls, furniture cabinets
or other.
2. If the floor is not
perfectly level, compen-
sate for any unevenness
by tightening or
loosening the adjustable
front feet (see figure);
the angle of inclination,
measured according to
the worktop, must not
exceed 2°.
Levelling your appliance correctly will provide it with
stability and avoid any vibrations, noise and shifting
during operation. If it is placed on a fitted or loose
carpet, adjust the feet in such a way as to allow
enough room for ventilation beneath the washing
machine.
Electric and water connections
Connecting the water inlet hose
1. Insert seal A into the
end of the inlet hose
and screw the latter
onto a cold water tap
with a 3/4 gas threaded
mouth (see figure).
Before making the
connection, allow the
water to run freely until
it is perfectly clear.
2. Connect the other end
of the water inlet hose to
the washing machine,
screwing it onto the
appliance's cold water
inlet, situated on the top
right-hand side on the
rear of the appliance
(see figure).
3. Make sure there are no kinks or bends in the
hose.
The water pressure at the tap must be within the
values indicated in the Technical details table
(on the next page).
If the water inlet hose is not long enough, contact
a specialist store or an authorised serviceman.
Installation
A
3
GB
Connecting the drain hose
Connect the drain hose,
without bending it, to a
draining duct or a wall
drain situated between
65 and 100 cm from the
floor;
alternatively, place it
over the edge of a
basin, sink or tub,
fastening the duct
supplied to the tap (see
figure). The free end of
the hose should not be
underwater.
We advise against the use of hose extensions; in
case of absolute need, the extension must have the
same diameter as the original hose and must not
exceed 150 cm in length.
Electric connection
Before plugging the appliance into the mains socket,
make sure that:
the socket is earthed and in compliance with the
applicable law;
the socket is able to sustain the appliance's
maximum power load indicated in the Technical
details table (on the right);
the supply voltage is included within the values i
ndicated on the Technical details table
(on the right);
the socket is compatible with the washing
machine's plug. If this is not the case, replace the
socket or the plug.
The washing machine should not be installed in an
outdoor environment, not even when the area is
sheltered, because it may be very dangerous to
leave it exposed to rain and thunderstorms.
When the washing machine is installed, the mains
socket must be within easy reach.
Do not use extensions or multiple sockets.
The power supply cable must never be bent or
dangerously compressed.
The power supply cable must only be replaced by
an authorised serviceman.
Warning! The company denies all liability if and when
these norms are not respected.
The first wash cycle
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle with
detergent and no laundry, setting the 90°C
programme without a pre-wash cycle.
ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description
65 - 100 cm
Technical details
Model
AVL 169
Dimensions
59.5 cm wide
85 cm high
53.5 cm deep
Capacity
from 1 to 5 kg
Electric
connections
voltage 220/230 Volts 50 Hz
maximum absorbed power 1850 W
Water
connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 46 litres
Spin speed
up to 1600 rpm
Control
programmes
according to
IEC456 directive
programme 3; temperature 60°C;
run with a load of 5 kg.
This appliance is compliant with the
following European Community
Directives:
- 73/23/CEE of 19/02/73 (Low
Voltage) and subsequent amendments
- 89/336/CEE of 03/05/89
(Electromagnetic Compatibility) and
subsequent amendments
- 2002/96/CE
4
GB
Control panel
Washing machine description
Detergent dispenser
Programme key
START/STOP
Button
START/RESET
Button
TEMPERATURE
Knob
PROGRAMME
Knob
Leds
FUNCTION
Buttons
SPIN SPEED
Knob
ON-OFF/DOOR LOCK
l
Led
Detergent dispenser: to add detergent and fabric
softener (see page 8).
Programme key: to consult a straightforward
chart of the different programmes available: pull the
grey tab outwards to open it.
LEDS: to find out which wash cycle phase is under
way.
If the Delay Timer function has been set, the time
left until the programme starts will be indicated (see
page 5).
SPIN SPEED knob: to set the spin speed or exclude
the spin cycle completely (see page 7).
FUNCTION buttons: to select the functions
available. The button corresponding to the function
selected will remain on.
TEMPERATURE knob: to set the temperature or
the cold wash cycle (see page 7).
START/STOP button: to turn the washing machine
on and off.
START/RESET button: to start the programmes or
cancel any incorrect settings.
ON-OFF/DOOR LOCK Led: to find out whether the
washing machine is on and if the appliance door can
be opened (see page 5).
PROGRAMME knob: to select the wash
programmes. The retractable control knob: press
the centre of the knob for it to pop out. The knob
stays still during the cycle.
5
GB
ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description
ON-OFF/DOOR LOCK led:
If this LED is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any
damages, wait for the LED to flash before you open the appliance door.
This model is fitted with a device that allows you to open the appliance door during the first phase of the
programme set. This is only possible when the LED is turned off.
The rapid flashing of the ON-OFF/DOOR LOCK Led together with the flashing of at least one other LED
indicates there is an abnormality. Call for Technical Assistance.
Cycle phase under way:
During the wash cycle, the LEDs gradually illuminate
on to indicate the cycle phase under way:
Prewash
Wash
Rinse
Spin cycle
Note: during draining, the LED corresponding to the
Spin cycle phase will be turned on.
Function buttons
The FUNCTION BUTTONS also act like LEDS.
When a function is selected, the corresponding button
is illuminated.
If the function selected is incompatible with the
programme set, the button will flash and the function
will not be enabled.
If you set a function that is incompatible with another
function you selected previously, only the last one
selected will be enabled.
Leds
The LEDS provide important information.
This is what they can tell you:
Delay set:
If the Delay Timer function has been enabled (see
page. 7), once you have started the programme,
the LED corresponding to the delay set will begin to
flash:
As time passes, the remaining delay will be
displayed, and the corresponding LED will flash:
Once the set delay is complete, the flashing LED will
turn off and the programme set will start.
6
GB
Type of fabric and degree of soil
Program-
mes
Wash
temperat.
Detergent
Fabric
softener
Cycle
length
(minutes)
Description of wash cycle
Pre-
wash
Wash
Cottons
Extremely soiled whites
(sheets, tablecloths, etc.)
1
90°C 137
Pre-wash, wash cycle, rinse cycles,
intermediate and final spin cycles
Extremely soiled whites
(sheets, tablecloths, etc.)
2
90°C 120
Wash cycle, rinse cycles, intermediate
and final spin cycles
Heavily soiled whites and fast
colours
3
60°C 105
Wash cycle, rinse cycles, intermediate
and final spin cycles
Slightly soiled whites and delicate
colours (shirts, jumpers, etc.)
4
40°C 72
Wash cycle, rinse cycles, intermediate
and final spin cycles
Slightly soiled delicate colours
5
30°C 65
Wash cycle, rinse cycles, intermediate
and final spin cycles
Synthetics
Heavily soiled fast colours
(baby linen, etc.)
6
60°C 77
Wash cycle, rinse cycles, anti-crease or
delicate spin cycle
Fast colours (all types of slightly
soiled garments)
6
40°C 62
Wash cycle, rinse cycles, anti-crease or
delicate spin cycle
Heavily soiled fast colours
(baby linen, etc.)
7
50°C 73
Wash cycle, rinse cycles, anti-crease or
delicate spin cycle
Delicate colours (all types of
slightly soiled garments)
8
40°C 58
Wash cycle, rinse cycles, anti-crease or
delicate spin cycle
Delicate colours (all types of
slightly soiled garments)
9
30°C 30
Wash cycle, rinse cycles and delicate
spin cycl
e
Delicates
Wool
10
40°C 50
Wash cycle, rinse cycles and delicate
spin cycle
Very delicate fabrics
(curtains, silk, viscose, etc.)
11
30°C 45
Wash cycle, rinse cycles, anti-crease or
draining cycle
PARTIAL PROGRAMMES
Rinse Rinse cycles and spin cycle
Delicate rinse cycle Rinse cycles, anti-crease or draining
Spin cycle Draining and heavy duty spin cycle
Delicate spin cycle Draining and delicate spin cycle
Draining Draining
Starting and Programmes
Programme table
Notes
For the anti-crease function: see Easy iron, opposite page. The information contained in the table is purely indicative.
Special programme
Daily 30' (programme 9 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only
lasts 30 minutes and allows you to save on both time and energy. By setting this programme (9 at 30°C), you can
wash different fabrics together (except for woollen and silk items), with a maximum load of 3 kg.
We recommend the use of liquid detergent.
Briefly: starting a programme
1. Switch the washing machine on by pressing button .
All the LEDS will light up for a few seconds and
the ON-OFF/DOOR LOCK Led will begin to flash.
2. Load your laundry into the washing machine and
shut the appliance door.
3. Set the PROGRAMME knob to the programme
required.
4. Set the wash temperature (see page 7).
5. Set the spin speed (see page 7).
6. Add the detergent and any fabric softener (see
page 8).
7. Start he programme by pressing the START/RESET
button.
To cancel it, keep the START/RESET button pressed
for at least 2 seconds.
8. When the programme is finished, the ON-OFF/
DOOR LOCK Led will flash to indicate that the
appliance door can be opened. Take out your
laundry and leave the appliance door ajar to allow
the drum to dry thoroughly. Turn the washing
machine off by pressing button
.
7
GB
Function Effect Comments
Enabled with
programmes:
Delay Timer
Delays the start
of the wash by
up to 9 hours.
Press the button repeatedly until the LED corresponding to the
desired delay is turned on.
The fifth time the button is pressed, the function will be disabled.
N.B.: Once you have pressed the Start/Reset button, the delay
can only be decreased if you wish to modify it.
All
Super
Wash
Allows for an
impeccable wash,
visibly whiter
than a standard
Class A
wash.
This function is incompatible with the RAPID function.
1, 2, 3, 4,
5, 6, 7, 8
Easy iron
This option
reduces the
amount of
creasing on
fabrics, making
them easier to
iron.
When this function is set, programmes 6, 7, 8, 11 and Delicate
rinse will end with the laundry left to soak (Anti-crease) and the
Rinse cycle phase LED will flash.
- to conclude the cycle, press the START/RESET button;
- to run the draining cycle alone, set the knob to the relative
symbol and press the START/RESET button.
All
programmes
except for
1, 2, 9, 10
and Draining.
Rapid
Cuts the duration
of the wash cycle
by 30%.
This function is incompatible with the SUPER WASH function.
1, 2, 3, 4,
5, 6, 7, 8
ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description
Personalisations
Setting the temperature
Turn the TEMPERATURE knob to set the wash temperature (see Programme table on page 6).
The temperature can be lowered, or even set to a cold wash (
).
Setting the spin speed
Turn the SPIN SPEED knob to set the spin speed for the programme selected.
The maximum spin speeds for each programme are as follows:
Programmes Maximum spin speed
Cottone 1600 rpm
Synthetics 800 rpm
Wool 600 rpm
Silk no
The spin speed can be lowered, or the spin cycle can be excluded altogether by selecting symbol
.
The washing machine will automatically prevent you from selecting a spin speed higher than the maximum speed
for each programme.
Functions
To enable a function:
1. press the button corresponding to the desired function, according to the table below;
2. the function is enabled when the corresponding button is illuminated.
Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the
programme set.
8
GB
Detergent dispenser
Good washing results also depend on the correct
dose of detergent: adding too much detergent won't
necessarily make for a more efficient wash, and may
in fact cause build up on the interior of your
appliance and even pollute the environment.
Open up the detergent
dispenser and pour in
the detergent and fabric
softener, as follows.
compartment 1: Detergent for pre-wash
(powder)
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in
immediately prior to the wash cycle start.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow from the grid.
Do not use hand wash detergent because it may
form too much foam.
Preparing your laundry
Divide your laundry according to:
- the type of fabric/the symbol on the label.
- the colours: separate coloured garments from
whites.
Empty all pockets and check for loose buttons.
Do not exceed the weight limits stated below,
which refer to the weight when dry:
Sturdy fabrics: max 5 kg
Synthetic fabrics: max 2.5 kg
Delicate fabrics: max 2 kg
Wool: max 1 kg
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1,200 g
1 towel 150-250 g
Special items
Curtains: fold curtains and place them in a pillow
case or mesh bag. Wash them separately without
exceeding half the appliance load. Use programme
11 which excludes the spin cycle automatically.
Quilted coats and windbreakers: if they are
padded with goose or duck down, they can be
machine-washed. Turn the garments inside out and
load a maximum of 2-3 kg, repeating the rinse cycle
once or twice and using the delicate spin cycle.
Trainers: remove any mud. They can be washed
together with jeans and other tough garments, but
not with whites.
Wool: for best results, use a specific detergent,
taking care not to exceed a load of 1 kg.
Woolmark Platinum Care
As gentle as a hand wash.
Ariston sets a new standard of superior
performance that has been endorsed by
The Woolmark Company with the prestigious
Woolmark Platinum Care brand. Look for the
Woolmark Platinum Care logo on the washing
machine to ensure you can safely and effectively
wash wool garments labelled as "hand wash"
(M.0303):
Set programme 10 for all "Hand wash"
(max 1 kg)
garments, using the appropriate detergent.
Detergents and laundry
1
2
3
9
GB
Precautions and advice
ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description
The washing machine was designed and built in
compliance with the applicable international safety
regulations. The following information is provided for
your safety and should consequently be read carefully.
General safety
This appliance has been designed for non-
professional, household use and its functions must
not be changed.
This washing machine should only be used by
adults and in accordance with the instructions
provided in this manual.
Never touch the washing machine when barefoot
or with wet or damp hands or feet.
Do not pull on the power supply cable to unplug
the appliance from the electricity socket. Pull the
plug out yourself.
Do not open the detergent dispenser while the
appliance is in operation.
Do not touch the drain water as it could reach
very high temperatures.
Never force the washing machine door: this could
damage the safety lock mechanism designed to
prevent any accidental openings.
In the event of a malfunction, do not under any
circumstances touch internal parts in order to
attempt repairs.
Always keep children well away from the
appliance while in operation.
The appliance door tends to get quite hot during
the wash cycle.
Should it have to be moved, proceed with the
help of two or three people and handle it with the
utmost care. Never try to do this alone, because
the appliance is very heavy.
Before loading your laundry into the washing
machine, make sure the drum is empty.
Disposal
Disposing of the packaging material:
observe local regulations, so the packaging can
be re-used.
The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment, requires that
old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected
separately in order to optimise the recovery and
recycling of the materials they contain and reduce
the impact on human health and the environment.
The crossed out "wheeled bin" symbol on the
product reminds you of your obligation, that when
you dispose of the appliance it must be separately
collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
Saving energy and respecting the
environment
Environmentally-friendly technology
If you only see a little water through your appliance
door, this is because thanks to the latest Ariston
technology, your washing machine only needs less
than half the amount of water to get the best results:
an objective reached to respect the environment.
Saving on detergent, water,
energy and time
To avoid wasting resources, the washing machine
should be used with a full load. A full load instead of
two half loads allows you to save up to 50% on energy.
The pre-wash cycle is only necessary on
extremely soiled garments. Avoiding it will save on
detergent, time, water and between 5 and 15%
energy.
Treating stains with a stain remover or leaving them
to soak before washing will cut down the need to
wash them at high temperatures. A programme at
60°C instead of 90°C or one at 40°C instead of
60°C will save up to 50% on energy.
Use the correct quantity of detergent depending
on the water hardness, how soiled the garments
are and the amount of laundry you have, to avoid
wastage and to protect the environment: despite
being biodegradable, detergents do contain
ingredients that alter the natural balance of the
environment. In addition, avoid using fabric
softener as much as possible.
If you use your washing machine from late in the
afternoon until the early hours of the morning, you
will help reduce the electricity board's peak load.
The Delay Timer option (see page 7) helps to
organise your wash cycles accordingly.
If your laundry has to be dried in a tumble dryer,
select a high spin speed. Having the least water
possible in your laundry will save you time and
energy in the drying process.
10
GB
Care and maintenance
Cutting off the water or electricity
supply
Turn off the water tap after every wash. This will
limit the wear of your appliance's water system
and also prevent leaks.
Unplug your appliance when cleaning it and
during all maintenance operations.
Cleaning your appliance
The exterior and rubber parts of your appliance can
be cleaned with a soft cloth soaked in lukewarm
soapy water. Do not use solvents or abrasives.
Cleaning the detergent dispenser
Remove the dispenser
by raising it and pulling it
out (see figure).
Wash it under running
water; this operation
should be repeated
frequently.
Caring for your appliance door and
drum
Always leave the appliance door ajar to prevent
unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cleaning
pump that does not require any maintenance.
Sometimes, small items (such as coins or buttons)
may fall into the pre-chamber that protects the
pump, situated in the lower part of the same.
Make sure the wash cycle has ended and unplug
the appliance.
To access the pre-chamber:
1. using a screwdriver,
remove the cover panel
on the lower front of the
washing machine (see
figure);
2. unscrew the lid
rotating it anti-
clockwise (see figure): a
little water may trickle
out. This is perfectly
normal;
3. clean the interior thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks are
securely in place before you push it onto the
appliance.
Checking the water inlet hose
Check the water inlet hose at least once a year. If
you see any cracks, replace it immediately: during
the wash cycles, water pressure is very strong and
a cracked hose could easily split open.
Never use hoses that have already been used.
1
2
11
GB
Your washing machine could fail to work. Before calling for Assistance (see page 12), make sure the problem
can't easily be solved by consulting the following list.
Troubleshooting
Problem
The washing machine won't
start.
The wash cycle won't start.
The washing machine fails to
load water.
The washing machine
continuously loads and unloads
water.
The washing machine does not
drain or spin.
The washing machine vibrates
too much during the spin cycle.
The washing machine leaks.
The ON-OFF/DOOR LOCK Led
flashes rapidly at the same
time as at least one other LED.
There is too much foam.
Possible causes/Solution:
The appliance is not plugged into the socket, or not enough to
make contact.
There has been a power failure.
The appliance door is not shut properly.
The
button has not been pressed.
The START/RESET button has not been pressed.
The water tap is not turned on.
A delayed start has been set (using the Delay Timer, see page 7).
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap is not turned on.
There is a water shortage.
The water pressure is insufficient.
The START/RESET button has not been pressed.
The drain hose is not fitted between 65 and 100 cm from the floor
(see page 3).
The free end of the hose is underwater (see page 3).
The wall drainage system doesn't have a breather pipe.
If the problem persists even after these checks, turn off the water tap,
switch the appliance off and call for Assistance. If the dwelling is on one of
the upper floors of a building, there may be drain trap problems causing the
washing machine to load and unload water continuously. In order to avoid
such an inconvenience, special anti-drain trap valves are available in shops.
The programme does not foresee the draining: some programmes
require enabling the draining manually (see page 6).
The Easy iron option is enabled: to complete the programme, press
the START/RESET button (see page 7).
The drain hose is bent (see page 3).
The drain duct is clogged.
The drum was not unblocked correctly during installation (see page 2).
The washing machine is not level (see page 2).
The washing machine is closed in between furniture cabinets and
the wall (see page 2).
The water inlet hose is not screwed on correctly (see page 2).
The detergent dispenser is obstructed (to clean it, see page 10).
The drain hose is not secured properly (see page 3).
Call for Assistance because this means there is an abnormality.
The detergent is not suitable for machine washing (it should bear
the definition "for washing machines" or "hand and machine wash",
or the like).
You used too much detergent.
ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description
12
GB
Before calling for Assistance:
Check whether you can solve the problem on your own (see page 11);
Restart the programme to check whether the problem has been solved;
If this is not the case, contact an authorised Technical Service Centre on the telephone number
provided on the guarantee certificate.
Always request the assistance of authorised servicemen.
Notify the operator of:
the type of problem;
the appliance model (Mod.);
the serial number (S/N).
This information can be found on the data plate situated on the rear of the washing machine.
Service
Service
13
DE
Deutsch
INHALTSVERZEICHNIS
Installation, 14-15
Auspacken und Aufstellen, 14
Wasser- und Elektroanschlüsse, 14-15
Erster Waschgang, 15
Technische Daten, 15
Beschreibung des
Waschvollautomaten, 16-17
Schalterblende, 16
Kontrollleuchten, 17
Inbetriebnahme und Programme, 18
Kurz zusammengefasst: Waschprogramm starten, 18
Programmtabelle, 18
Individualisierungen, 19
Einstellen der Temperatur, 19
Einstellen der Schleuder, 19
Funktionen, 19
Waschmittel und Wäsche, 20
Waschmittelschublade, 20
Vorsortieren der Wäsche, 20
Besondere Wäscheteile, 20
Woolmark Platinum Care, 20
Vorsichtsmaßregeln und Hinweise, 21
Allgemeine Sicherheit, 21
Entsorgung, 21
Energie sparen und Umwelt schonen, 21
Reinigung und Pflege, 22
Wasser- und Stromversorgung abstellen, 22
Reinigung des Gerätes, 22
Reinigung der Waschmittelschublade, 22
Pflege der Gerätetür und Trommel, 22
Reinigung der Pumpe, 22
Kontrolle des Wasserzulaufschlauchs, 22
Störungen und Abhilfe, 23
Kundendienst, 24
Bevor Sie sich an den Kundendienst wenden, 24
DE
WASCHVOLLAUTOMAT
AVL 169
Bedienungsanleitungen
14
DE
Es ist äußerst wichtig, diese Bedienungsanleitung
sorgfältig aufzubewahren, um sie jederzeit zu Rate ziehen
zu können. Sorgen Sie dafür, dass sie im Falle eines
Umzugs oder Übergabe an einen anderen Benutzer das
Gerät stets begleitet, damit auch der neue Inhaber die
Möglichkeit hat, diese zu Rate zu ziehen.
Lesen Sie bitte folgende Hinweise aufmerksam durch,
sie liefern wichtige Informationen hinsichtlich der Installa-
tion, dem Gebrauch und der Sicherheit.
Auspacken und Aufstellen
Auspacken
1. Gerät auspacken.
2. Sicherstellen, dass der Waschvollautomat keine Transport-
schäden erlitten hat. Im Falle einer Beschädigung Gerät bitte
nicht anschließen, sondern den Kundendienst anfordern.
3. Die vier Transport-
schutzschrauben aus-
schrauben und das an
der Rückwand befindli-
che Gummiteil nebst
entsprechendem
Distanzstück abnehmen
(siehe Abbildung).
4. Die Löcher mittels der mitgelieferten Kunststoffstöpsel
schließen.
5. Sämtliche Teile aufbewahren: Sollte der Waschvoll-
automat erneut transportiert werden müssen, müssen
diese Teile wieder eingesetzt werden.
Verpackungsmaterial ist kein Spielzeug für Kinder
Standfläche
1. Der Waschvollautomat muss auf einem ebenen, festen
Untergrund aufgestellt werden, ohne ihn an Wände, Möbelteile
oder ähnliches anzulehnen.
2. Sollte der Boden nicht
perfekt eben sein, müssen
die Unebenheiten durch
An- bzw. Ausdrehen der
vorderen Stellfüße ausge-
glichen werden (siehe
Abbildung), der auf der
Arbeitsfläche zu ermitteln-
de Neigungsgrad darf
nicht überschreiten.
Eine präzise Nivellierung verleiht dem Gerät die erforderliche
Stabilität, durch die Vibrationen, Betriebsgeräusche und ein
Verrücken des Gerätes vermieden werden. Bei Teppichbö-
den müssen die Stellfüße so reguliert werden, dass ein
ausreichender Freiraum zur Belüftung unter dem Waschvoll-
automaten gewährleistet ist.
Wasser- und Elektroanschlüsse
Anschluss des Zulaufschlauches
1. Legen Sie die Gummi-
dichtung A in das
Anschlussstück des
Zulaufschlauches ein und
drehen Sie dieses an
einen mit
Gewindeanschluss von ¾
G versehenen Kaltwasser-
hahn (siehe Abbildung).
Lassen Sie das Wasser
vor dem Anschluss so lange auslaufen, bis klares
Wasser austritt.
2. Schließen Sie das
andere Ende des Schlau-
ches an den oben rechts
am Rückteil des Wasch-
vollautomaten befindli-
chen Wasseranschluss
an (siehe Abbildung).
3. Der Schlauch darf hierbei nicht eingeklemmt oder
abgeknickt werden.
Der Wasserdruck muss innerhalb der Werte liegen,
die in der Tabelle der Technischen Daten angegebenen
sind (siehe nebenstehende Seite).
Sollte der Zulaufschlauch nicht lang genug sein, dann
wenden Sie sich bitte an einen Fachhändler oder an
einen autorisierten Fachmann.
Installation
A
15
DE
Anschluss des Ablaufschlauches
Schließen Sie den Ablauf-
schlauch, ohne ihn dabei
zu krümmen, an eine
Ablaufleitung, oder an
einen in der Wand in einer
Mindesthöhe von 65 - 100
cm angelegten Ablauf an;
oder hängen Sie ihn in ein
Becken oder eine Wanne
ein; befestigen Sie ihn in
diesem Falle mittels der
mitgelieferten Führung an
dem Wasserhahn (siehe
Abbildung). Das freie
Ablaufschlauchende darf
nicht unter Wasser
bleiben.
Verlängerungsschläuche sollten nicht eingesetzt
werden, sollte dies jedoch absolut unvermeidlich sein,
muss die Verlängerung denselben Durchmesser des
Originalschlauchs aufweisen und 150 cm nicht über-
schreiten.
Elektronschluss
Vor Einfügen des Steckers in die Steckdose ist sicherzu-
stellen, dass:
die Steckdose über eine normgerechte Erdung
verfügt;
die Steckdose die in nebenstehender Datentabelle
angegebene Höchstlast des Gerätes trägt;
die Stromspannung den in nebenstehender Daten-
tabelle aufgeführten Werten entspricht;
der Stecker in die Steckdose passt. Andernfalls muss
der Stecker (oder die Steckdose) ersetzt werden.
Der Waschvollautomat darf nicht im Freien installiert
werden, auch nicht, wenn es sich um einen geschützten
Platz handelt. Es ist gefährlich, Ihren Vollwaschautomaten
Gewittern und Unwettern auszusetzen.
Die Steckdose sollte nach installiertem Gerät leicht
zugänglich sein.
Verwenden Sie bitte keine Verlängerungen oder
Mehrfachstecker.
Das Kabel darf nicht gebogen bzw. eingeklemmt
werden.
Das Versorgungskabel darf nur durch autorisierte
Fachkräfte ausgetauscht werden.
Achtung! Der Hersteller weist jede Haftung zurück, falls
diese Vorschriften nicht eingehalten werden sollten.
Erster Waschgang
Lassen Sie nach der Installation bzw. vor erstmaligem
Gebrauch erst einen Waschgang (mit Waschmittel) ohne
Wäsche durchlaufen. Stellen Sie hierzu das 90°C-
Waschprogramm ohne Vorwäsche ein.
KundendienstStörungenVorsichtsmaßregeln
Wartung und
Pflege
Waschprogramme WaschmittelInstallation Beschreibung
65 - 100 cm
Technische Daten
Modell
AVL 169
Abmessungen
Breite 59,5 cm
Höhe 85 cm
Tiefe 53,5 cm
Fassungsvermögen
1 bis 5 kg
Elektroanschlüsse
Spannung 220/230 Volt 50 Hz
max. Leistungsaufnahme 1850 W
Wasseranschlüsse
chstdruck 1 MPa (10 bar)
Mindestdruck 0,05 MPa (0,5 bar)
Trommelvolumen 46 Liter
Schleudertouren
bis zu 1600 U/min.
Prüfprogramme
gemäß IEC456
Programm 3; Temperatur 60°C;
bei einer Lademenge von 5 kg.
Dieses Gerät entspricht den
folgenden EG-Richtlinien:
- 73/23/EWG vom 19.02.73
(Niederspannung)
und nachfolgenden Änderungen
- 89/336/EWG vom 03.05.89
(elektromagnetische Verträglichkeit)
und nachfolgenden Änderungen
- 2002/96/CE
16
DE
Schalterblende
Beschreibung des
Waschvollautomaten
Waschmittelschublade
Anzeigetafel
Taste
EIN/AUS
Taste
START/RESET
Waschmittelschublade: für Waschmittel und
Zusätze (siehe Seite 20).
Anzeigetafel: die zu jeder Zeit einen klaren Überblick
über die möglichen Programme gewährleistet. Ganz
einfach an der grauen Zunge herausziehen.
Kontrollleuchten: Zur Kontrolle des Wasch-
programmablaufs.
Wurde die Funktion Delay Timer eingestellt, wird die
bis zum Start noch verbleibende Zeit
Angezeigt (siehe Seite 17).
Wahlschalter SCHLEUDER: Zur Einstellung oder zum
völligen Ausschalten der Schleuder (siehe Seite 19).
Tasten FUNKTIONEN: Zur Einstellung der verfügbaren
Funktionen. Die gewählte Einstellung der entsprechen-
den Funktionstaste bleibt eingeschaltet (sie leuchtet).
Wahlschalter TEMPERATUR: Zur Einstellung der
Waschtemperatur oder der Kaltwäsche (siehe Seite 19).
Taste "EIN/AUS": zur Ein- und Ausschaltung des
Waschvollautomaten
Taste "START/RESET": um die Programme zu
starten bzw. zu löschen, falls unkorrekt eingestellt.
Kontrollleuchte ON/FÜLLFENSTER GESPERRT: Um
Erkennen zu können, ob die Maschine eingeschaltet
ist und demnach das Füllfenster nicht geöffnet werden
kann (siehe Seite 17).
Wahlschalter PROGRAMME: zur Programmwahl Die
Wahlschalter sind flächenbündig angebracht: Durch
leichten Druck auf die Knopfmitte können Sie heraus-
gezogen werden. Während des Programmablaufs
bleibt der Schalter feststehend.
Wahlschalter
TEMPERATUR
Wahlschalter
PROGRAMME
Kontrollleuchten
Taste
FUNKTIONEN
Wahlschalter
SCHLEUDER
Kontrollleuchte
ON/FÜLLFENSTER
GESPERRT
17
DE
KundendienstStörungenVorsichtsmaßregeln
Wartung und
Pflege
Waschprogramme WaschmittelInstallation Beschreibung
Kontrollleuchte ON/FÜLLFENSTER GESPERRT:
Ist diese Kontrollleuchte eingeschaltet, bedeutet dies, dass das Füllfenster gesperrt ist. Um ungewolltes Öffnen zu
vermeiden, warten Sie, bis die Leuchte auf Blinklicht umschaltet, bevor Sie das Fenster öffnen, um Schäden zu
vermeiden.
Dieses Modell ist mit einer Vorrichtung ausgestattet, dank der das Füllfenster während der ersten Programmphase
noch geöffnet werden kann. Dies ist jedoch nur möglich, wenn die Kontrollleuchte ausgeschaltet ist.
Ein gleichzeitiges, rasches Blinken der Kontrollleuchte ON/FÜLLFENSTER GESPERRT mit einer beliebigen anderen
Kontrollleuchte signalisiert einen Fehler. Fordern Sie den Kundendienst an.
Laufende Programmphase:
Während des Waschprogrammablaufs leuchten die
Kontrollleuchten nach und nach auf und zeigen so den
jeweiligen Stand an.
Vorwäsche
Hauptwäsche
Spülen
Schleudern
Anmerkung: Während des Abpumpens leuchtet die
entsprechende Kontrollleuchte für die Schleuder auf.
Tasten FUNKTIONEN
Die Funktionstasten fungieren auch als Kontrollleuchten.
Bei Wahl einer Funktion leuchtet die entsprechende
Taste auf.
Ist die gewählte Funktion nicht vereinbar mit dem einge-
stellten Programm, schaltet die Taste auf Blinklicht und
die Funktion wird nicht aktiviert.
Wird eine Funktion eingestellt, die zu der bereits einge-
stellten nicht zugeschaltet werden kann, bleibt nur die
zuletzt gewählte aktiv.
Kontrollleuchten
Die Kontrollleuchten liefern wichtige Hinweise.
Sie signalisieren:
Startvorwahl erfolgt:
Wurde die Startvorwahl-Funktion Delay Timer (siehe
Seite 19) aktiviert, und das Programm in Gang gesetzt,
schaltet die Kontrollleuchte, die der eingestellten
Zeitverschiebeung entspricht, auf Blinklicht:
Nach und nach wird die bis zum effektiven Start
noch verbleibende Zeit eingeblendet, die entspre-
chende Kontrollleuchte blinkt:
Nach Ablauf der vorgewählten Zeit erlischt die
Kontrollleuchte und das gewählte Waschprogramm
startet.
18
DE
Gewebeart und Verschmutzungsgrad
Wasch-
programme
Te m p e -
ratur
Waschmittel
Weich-
macher
Programm-
Dauer
(Minuten)
Beschreibung des Waschprogramms
Vorw. Hauptw.
Baumwolle
Stark verschmutzteKochwäsche
(Bettücher, Tischdecken usw.)
1
90°C 137
Vorwäsche, Hauptwäsche, Spülen,
Zwischen- und Endschleudern
Stark verschmutzteKochwäsche
(Bettücher, Tischdecken usw.)
2
90°C 120
Hauptwäsche, Slen, Zwischen-
und Endschleudern
Widerstandsfähige, stark
verschmutzte Weiß- und Buntwäsche
3
60°C 105
Hauptwäsche, Slen, Zwischen-
und Endschleudern
Leicht verschmutzte Weißwäsche
und empfindliche Buntwäsche
(Oberhemden, Maschenwareusw.)
4
40°C 72
Hauptwäsche, Slen, Zwischen-
und Endschleudern
Leicht verschmutzte empflindliche
Buntwäsche
5
30°C 65
Hauptwäsche, Slen, Zwischen-
und Endschleudern
Synthetik
Stark verschmutzte, farbechte
Buntwäsche (Babysche usw.)
6
60°C 77
Hauptwäsche, Slen, Knitterschutz
oder sanftes Schleudern
Waschechte Farben (leicht
verschmutzte Wäsche jeder Art).
6
40°C 62
Hauptwäsche, Slen, Knitterschutz
oder sanftes Schleudern
Stark verschmutzte, farbechte
Buntwäsche (Babysche usw.)
7
50°C 73
Hauptwäsche, Slen, Knitterschutz
oder sanftes Schleudern
Zarte Farben (leicht verschmutzte
Wäsche jeder Art).
8
40°C 58
Hauptwäsche, Slen, Knitterschutz
oder sanftes Schleudern
Zarte Farben (leicht verschmutzte
Wäsche jeder Art).
9
30°C 30
Hauptwäsche, Slen und sanftes
Schleudern
Wolle/seide
Wolle
10
40°C 50
Hauptwäsche, Slen und sanftes
Schleudern
Sehr zarte Feinwäsche (Gardinen,
Seide, Viskose, usw.)
11
30°C 45
Hauptwäsche, Slen, Knitterschutz
oder Wasser abpumpen
TEILPROGRAMME
Spülen Spülen und Schleudern
Sanftes Spülen
Spülen, Knitterschutz oder
Abpumpen
Schleudern
Abpumpen und energisches
Schleudern
Sanftes Schleudern Abpumpen und sanftes Schleudern
Abpumpen Abpumpen
Inbetriebnahme und
Programme
Programmtabelle
Anmerkungen
Zum Knitterschutz: siehe "Bügelleicht", auf nebenstehender Seite. Bei den in der Tabelle aufgeführten Daten handelt
es sich um Richtwerte.
Spezialprogramm
Kurzprogramm 30' (Programm 9 für Kunstfasern) Kurzprogramm für die tägliche Wäsche leicht verschmutzter Teile:
in nur 30 Minuten, zur Einsparung von Zeit und Energie. Stellen Sie dieses Waschprogramm (9 bei 30°C) ein, dann
können, bei einer maximalen Lademenge von 3 kg, Gewebe unterschiedlicher Art (mit Ausnahme von Wolle und
Seide) zusammen gewaschen werden. Es ist ratsam, flüssige Waschmittel einzusetzen.
Kurz zusammengefasst:
Waschprogramm starten
1. Schalten Sie den Waschvollautomaten durch Druck
auf die Taste
ein. Alle Kontrollleuchten leuchten für
einige Sekunden auf, und erlöschen kurz darauf
wieder. Die Kontrollleuchte ON/FÜLLFENSTER
GESPERRT schaltet auf Blinklicht.
2. Wäsche einfüllen und Füllfenster schließen.
3. Stellen Sie das gewünschte Programm mittels des
Wahlschalters PROGRAMME ein.
4. Einstellen der Waschtemperatur (siehe Seite 19).
5. Einstellen der Schleudergeschwindigkeit (siehe Seite 19).
6. Waschmittel und Zusätze einfüllen (siehe Seite 20).
7. Programm durch Druck auf die Taste START/RESET
in Gang setzen.
Um dieses zu löschen, Taste START/RESET für
mindestens 2 Sekunden gedrückt halten.
8. Ist das Waschprogramm abgelaufen schaltet die
Kontrollleuchte ON/FÜLLFENSTER GESPERRT auf
Blinklicht, was anzeigt, dass das Fenster geöffnet
werden kann. Nehmen Sie die Wäsche heraus und
lassen Sie das Füllfenster leicht offen stehen, damit
die Trommel trocknen kann. Die Waschmaschine
nun durch Druck auf die Taste
ausschalten.
19
DE
Funktionen Wirkung Anleitungen zur Anwendung
Aktiv mit den
Programmen:
Delay Timer
(Startvorwahl)
Start kann bis zu 9
Std. verschoben
werden.
Drücken Sie die Taste so oft, bis die Kontrollleuchte der
gewünschten Zeitverschiebung aufleuchtet.
Ein nfter Tastendruck deaktiviert die Funktion.
NB: Ist die Taste START/RESET einmal gedrückt, kann der
gewählte Zeitverschiebungswert nur noch herabgesetzt werden.
Alle
Super Wash
Für einwandfrei
saubere, sichtbar
weere Wäsche des
Klasse A-Standards.
Nicht mit der Funktion KURZ zu kombinieren.
1, 2, 3, 4,
5, 6, 7, 8
gelleicht
Reduziert die
Knitterbildung und
erleichtert so das
Bügeln.
Wurde diese Funktion eingestellt, werden die Programme 6, 7, 8,
11 und Sanftes Spülen unterbrochen, das Wasser wird nicht
abgepumpt, die Wäsche bleibt im Wasser liegen (Knitterschutz),
und die Kontrollleuchte der Spülphase schaltet auf Blinklicht:
- um den Waschgang zu beenden, Taste START/SELECT drücken;
- nur das Wasser abpumpen: Knopf auf das entsprechende Symbol
drehen und die Taste START/RESET drücken.
Alle, mit
Ausnahme
1, 2, 9, 10,
Abpumpen.
Kurz
Verkürzt die Dauer
des
Waschvorgangs
um ca. 30%.
Nicht mit der Funktion SUPER WASH zu kombinieren.
1, 2, 3, 4,
5, 6, 7, 8
Individualisierungen
KundendienstStörungenVorsichtsmaßregeln
Wartung und
Pflege
Waschprogramme WaschmittelInstallation Beschreibung
Einstellen der Temperatur
Durch Drehen des Wahlschalters TEMPERATUR wird die Waschtemperatur eingestellt. (siehe Programmtabelle auf Seite 18).
Die Temperatur kann bis auf Kaltwäsche (
) herabgesetzt werden.
Einstellen der Schleuder
Durch Drehen des Wahlschalters SCHLEUDER wird die Schleudergeschwindigkeit des gewählten Waschprogramms
eingestellt.
Folgende Höchstgeschwindigkeiten sind für die einzelnen Programme vorgesehen:
Waschprogramme Höchstgeschwindigkeit
Baumwolle 1600 U/min
Kunstfasern 800 U/min
Wolle 600 U/min
Seide no
Die Schleudergeschwindigkeit kann herabgesetzt; durch Wahl des Symbols
kann die Schleuder gänzlich ausge-
schlossen werden.
Der Waschvollautomat verhindert automatisch ein höheres Schleudern, falls die für das entsprechende Programm
vorgeschriebene Schleuderdrehzahl überstiegen wird.
Funktionen
Die verschiedenen Waschfunktionen, die Ihnen Ihr Waschvollautomat bietet, ermöglichen es Ihnen, hygienisch saubere
und weiße Wäsche zu erhalten, die Ihren Wünschen entsprechen. Aktivierung der Funktionen:
1. Die Taste der gewünschten Funktion gemäss untenstehender Tabelle drücken;
2. Das Einschalten bzw. Aufleuchten der entsprechenden Taste zeigt an, dass die Funktion aktiviert wurde.
Anmerkung: Sollte die Taste jedoch auf Blinklicht schalten, bedeutet dies, dass die Funktion zu dem eingestellten Pro-
gramm nicht zugeschaltet werden kann.
20
DE
Waschmittelschublade
Ein gutes Waschergebnis hängt auch von einer korrekten
Waschmitteldosierung ab: Eine zu hohe Dosierung
bedeutet nicht unbedingt reinere Wäsche, sie trägt nur
dazu bei, die Maschineninnenteile zu verkrusten und die
Umwelt zu belasten.
Schublade herausziehen
und Waschmittel oder
Zusätze wie folgt einfüllen:
In Kammer 1: Waschpulver für die Vorwäsche
(kein Flüssigwaschmittel)
In Kammer 2: Waschmittel für die Haupt-
wäsche (Waschpulver oder Flüssigwaschmittel)
Flüssigwaschmittel nur kurz vor dem Start einfüllen.
In Kammer 3: Zusätze (Weichspüler usw.)
Der Weichspüler darf das Gitter nicht übersteigen.
Verwenden Sie keine Handwaschmittel, sie verursa-
chen eine zu hohe Schaumbildung.
Vorsortieren der Wäsche
Sortieren Sie die Wäsche nach:
- Gewebeart / Waschetikettensymbol
- und Farben: Buntwäsche von Weißwäsche
trennen.
Entleeren Sie alle Taschen.
Das angegebene Gewicht, das sich auf die maximale
Ladung an Trockenwäsche bezieht, sollte nicht
überschritten werden:
Widerstandsfähige Gewebe: max 5 kg
Kunstfasergewebe: max 2,5 kg
Feinwäsche: max 2 kg
Wolle: max 1 kg
Wie schwer ist Wäsche?
1 Bettuch 400-500 gr
1 Kissenbezug 150-200 gr
1 Tischdecke 400-500 gr
1 Bademantel 900-1.200 gr
1 Handtuch 150-250 gr
Besondere Wäscheteile
Gardinen:Gardinen zusammengefaltet in einem
Kissenbezug oder in einem netzartigen Beutel wa-
schen. Waschen Sie diese allein, ohne das Gesamtge-
wicht für halbe Füllung zu übersteigen. Stellen Sie das
Programm 11 ein, das ein automatisches Ausschließen
der Schleuder vorsieht.
Skijacken und Anoraks: Sind diese mit Gänse-
oder Daunenfedern gefüttert, können sie im Wasch-
vollautomaten gewaschen werden. Ziehen Sie die Teile
auf links, achten Sie auf eine maximale Beladung von
2/3 kg, wiederholen Sie 2/3 Spülgänge und stellen Sie
die Schleuder auf Schonschleudern ein.
Tennisschuhe: Entfernen Sie Schlammreste. Tennis-
schuhe können zusammen mit Jeans oder sonstigen
widerstandsfähigen Teilen, nicht jedoch mit Weiß-
wäsche, gewaschen werden.
Wolle: Verwenden Sie Spezialwaschmittel; Lade-
menge von 1 kg bitte nicht überziehen.
Woolmark Platinum Care
Schonend wie Waschen von Hand.
Ariston hat einen neuen Standard hochwertiger
Leistungen geschaffen, der von The Woolmark
Company mit dem prestigevollen Warenzeichen Woolmark
Platinum Care zugelassen wurde. Befindet sich auf Ihrem
Waschvollautomaten das Logo Woolmark Platinum Care,
können Teile aus Schurwolle, die mit dem Pflegeetikett
"Handwäsche" ausgezeichnet sind, darin gewaschen
werden (M.0303):
Verwenden Sie für alle mit "Handwäsche"
(max 1 kg)
ausgezeichneten Teile das Programm 10 und Spezial-
waschmittel.
Waschmittel und Wäsche
1
2
3
1 / 1

Whirlpool AVL 169 (EU) Manualul utilizatorului

Categorie
Mașini de spălat
Tip
Manualul utilizatorului