Indesit EWD 61051 W EU Manualul utilizatorului

Categorie
Mașini de spălat
Tip
Manualul utilizatorului
GB
1
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 4
Cutting off the water or electricity supply
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 5
General safety
Disposal
Description of the washing machine
and starting a wash cycle, 6-7
Control panel
Indicator lights
Starting a wash cycle
Wash cycles, 8
Table of wash cycles
Fast daily cycles
Personalisation, 9
Setting the temperature
Setting the spin speed
Functions
Detergents and laundry, 10
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Load balancing system
Troubleshooting, 11
Service, 12
EWD 61051
Instructions for use
WASHING MACHINE
English,1
GB
SK
DE
Slovensky,37
CZ
Český,25
RO
Deutsch,13
Română,49
2
GB
! This instruction manual should be kept in a safe
place for future reference. If the washing machi-
ne is sold, transferred or moved, make sure that
the instruction manual remains with the machine
so that the new owner is able to familiarise him-
self/herself with its operation and features.
! Read these instructions carefully: they con-
tain vital information relating to the safe instal-
lation and operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its
packaging.
2. Make sure that the washing machine has
not been damaged during the transportation
process. If it has been damaged, contact the
retailer and do not proceed any further with
the installation process.
3. Remove the 3 pro-
tective screws (used
during transportation)
and the rubber wa-
sher with the cor-
responding spacer,
located on the rear
part of the appliance
(see figure).
4. Close off the holes using the plastic plugs
provided.
5. Keep all the parts in a safe place: you will
need them again if the washing machine ne-
eds to be moved to another location.
! Packaging materials should not be used as
toys for children.
Levelling
1. Install the washing machine on a flat sturdy
floor, without resting it up against walls, furni-
ture cabinets or anything else.
2. If the floor is not
perfectly level, com-
pensate for any une-
venness by tightening
or loosening the
adjustable front feet
(see figure); the angle
of inclination, measu-
red in relation to the
worktop, must not
exceed 2°.
Levelling the machine correctly will provide
it with stability, help to avoid vibrations and
excessive noise and prevent it from shifting
while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow
a sufficient ventilation space underneath the
washing machine.
Connecting the electricity and
water supplies
Connecting the water inlet hose
1. Connect the sup-
ply pipe by screwing
it to a cold water tab
using a ¾ gas threa-
ded connection (see
figure).
Before performing the
connection, allow the
water to run freely un-
til it is perfectly clear.
2. Connect the inlet
hose to the washing
machine by screwing
it onto the correspon-
ding water inlet of the
appliance, which is
situated on the top
right-hand side of the
rear part of the ap-
pliance (see figure).
3. Make sure that the hose is not folded over
or bent.
! The water pressure at the tap must fall within
the values indicated in the Technical details
table (see next page).
! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
Installation
GB
3
65 - 100 cm
Connecting the drain hose
Connect the drain
hose, without bending
it, to a drainage duct
or a wall drain located
at a height between
65 and 100 cm from
the floor;
alternatively, rest it on
the side of a washba-
sin or bathtub, faste-
ning the duct sup-
plied to the tap (see
figure). The free end
of the hose should
not be underwater.
! We advise against the use of hose exten-
sions; if it is absolutely necessary, the exten-
sion must have the same diameter as the
original hose and must not exceed 150 cm in
length.
Electrical connections
Before plugging the appliance into the electri-
city socket, make sure that:
•thesocketisearthedandcomplieswithall
applicable laws;
•thesocketisabletowithstandthemaximum
power load of the appliance as indicated in
the Technical data table (see opposite);
•thepowersupplyvoltagefallswithinthe
values indicated in the Technical data table
(see opposite);
•thesocketiscompatiblewiththeplugof
the washing machine. If this is not the case,
replace the socket or the plug.
! The washing machine must not be installed
outdoors, even in covered areas. It is extreme-
ly dangerous to leave the appliance exposed
to rain, storms and other weather conditions.
! When the washing machine has been instal-
led, the electricity socket must be within easy
reach.
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
! The power supply cable must only be repla-
ced by authorised technicians.
Warning! The company shall not be held
responsible in the event that these regulations
are not respected.
The first wash cycle
Once the appliance has been installed, and
before you use it for the first time, run a wash
cycle with detergent and no laundry, using the
wash cycle 2.
Technical data
Model
EWD 61051
Dimensions
width 59.5 cm
height 85 cm
depth 51,7 cm
Capacity
from 1 to 6 kg
Electrical
connections
please refer to the technical
data plate fixed to the ma-
chine
Water con-
nection
maximum pressure 1 MPa
(10 bar)
minimum pressure 0.05
MPa (0.5 bar)
drum capacity 46 litres
Spin speed
up to 1000 rotations per
minute
Test wash
cycles in
accordance
with re-
gulations
1061/2010
and
1015/2010
Programme 15:
Eco Cotton 6C.
Programme 15:
Eco Cotton 4C.
This appliance conforms to
the following EC Directives:
- 2004/108/EC (Electroma-
gnetic Compatibility)
- 2012/19/EU - WEEE
- 2006/95/EC Low Voltage)
4
GB
Care and maintenance
Cutting off the water and electri-
city supplies
•Turnoffthewatertapaftereverywashcycle.
This will limit wear on the hydraulic system
inside the washing machine and help to pre-
vent leaks.
•Unplugthewashingmachinewhencleaning
it and during all maintenance work.
Cleaning the washing machine
The outer parts and rubber components of the
appliance can be cleaned using a soft cloth
soaked in lukewarm soapy water. Do not use
solvents or abrasives.
Cleaning the detergent dispenser
drawer
Remove the dispenser
by raising it and pul-
ling it out (see figure).
Wash it under running
water; this operation
should be repeated
frequently.
Caring for the door and drum of
your appliance
•Alwaysleavetheportholedoorajarinorder
to prevent unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-clea-
ning pump which does not require any mainte-
nance. Sometimes, small items (such as coins
or buttons) may fall into the pre-chamber which
protects the pump, situated in its bottom part.
! Make sure the wash cycle has finished and
unplug the appliance.
To access the pre-chamber:
1. using a screwdri-
ver, remove the cover
panel on the lower
front part of the wa-
shing machine (see
figure);
2. unscrew the lid
by rotating it anti-
clockwise (see figu-
re): a little water may
trickle out. This is
perfectly normal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks
are securely in place before you push it onto
the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If
there are any cracks, it should be replaced
immediately: during the wash cycles, water
pressure is very strong and a cracked hose
could easily split open.
! Never use second-hand hoses.
GB
5
Precautions and tips
! This washing machine was designed and constructed in
accordance with international safety regulations. The fol-
lowing information is provided for safety reasons and must
therefore be read carefully.
General safety
•Thisappliancewasdesignedfordomesticuseonly.
This appliance can be used by children aged
from 8 years and above and persons with re-
duced physical, sensory or mental capabilities
or lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved. Chil-
dren shall not play with the appliance. Clea-
ning and user maintenance shall not be made
by children without supervision.
•Donottouchthemachinewhenbarefootorwithwetor
damp hands or feet.
•Donotpullonthepowersupplycablewhenunplugging
the appliance from the electricity socket. Hold the plug
and pull.
•Donotopenthedetergentdispenserdrawerwhilethe
machine is in operation.
•Donottouchthedrainedwaterasitmayreachextreme-
ly high temperatures.
•Neverforcetheportholedoor.Thiscoulddamagethe
safety lock mechanism designed to prevent accidental
opening.
•Iftheappliancebreaksdown,donotunderanycircum-
stances access the internal mechanisms in an attempt
to repair it yourself.
•Alwayskeepchildrenwellawayfromtheappliancewhile
it is operating.
•Thedoorcanbecomequitehotduringthewashcycle.
•Iftheappliancehastobemoved,workinagroupoftwo
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
•Beforeloadinglaundryintothewashingmachine,make
sure the drum is empty.
Disposal
•Disposingofthepackagingmaterials:observelocal
regulations so that the packaging may be re-used.
• TheEuropeanDirective2012/19/EU-WEEEonWaste
Electrical and Electronic Equipment, requires that
old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected separately
in order to optimise the recovery and recycling of the
materials they contain and reduce the impact on human
health and the environment. The crossed out “wheeled
bin” symbol on the product reminds you of your obliga-
tion, that when you dispose of the appliance it must be
separately collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
6
GB
Detergent dispenser drawer: used to dispense
detergents and washing additives (see “Detergents and
laundry”).
ON/OFF button: switches the washing machine on and
off.
WASH CYCLE knob: programmes the wash cycles. Du-
ring the wash cycle, the knob does not move.
FUNCTION buttons with indicator light: used to select the
available functions. The indicator light corresponding to the
selected function will remain lit.
TEMPERATURE knob: sets the temperature or the cold
wash cycle (see “Personalisation”).
SPIN SPEED knob: sets the spin speed or exclude the
spin cycle completely (see “Personalisation”).
DISPLAY: used to view the duration of the various cycles
available and the remaining time of a cycle in progress;
iftheDELAYTIMERoptionhasbeenselected,the
countdown to the start of the selected cycle will appear.
DELAY TMER button : press to set a delayed start
time for the selected wash cycle. The delay time will be
shown on the display.
WASH CYCLE PROGRESS
indicator light
s: used to
monitor the progress of the wash cycle.
The illuminated indicator light shows which phase is in
progress.
DOOR LOCKED indicator light: indicates whether the
door may be opened or not (see next page).
START/PAUSE button with indicator light: starts or tem-
porarily interrupts the wash cycles.
N.B. To pause the wash cycle in progress, press this
button; the corresponding indicator light will flash orange,
while the indicator light for the current wash cycle phase
will remain lit in a fixed manner. If the DOOR LOCKED
indicator light is switched off, the door may be opened
(wait approximately 3 minutes).
To start the wash cycle from the point at which it was inter-
rupted, press this button again.
Standby mode
This washing machine, in compliance with new energy sa-
ving regulations, is fitted with an automatic standby system
which is enabled after about 30 minutes if no activity is
detected. Press the ON-OFF button briefly and wait for the
machine to start up again.
Description of the washing
machine and starting a wash cycle
WASH CYCLE
PROGRESS
DOOR LOCKED
indicator light
START/
PAUSE
button with
indicator light
Control panel
Detergent dispenser drawer
ON/OFF
button
WASH CYCLE
knob
TEMPERATURE
knob
FUNCTION
buttons with
indicator lights
SPIN SPEED
knob
DISPLAY
DELAY TIMER
button
GB
7
Indicator lights
The indicator lights provide important information.
This is what they can tell you:
Wash cycle phase indicator lights
Once the desired wash cycle has been selected and has
begun, the indicator lights switch on one by one to indicate
which phase of the cycle is currently in progress.
Function buttons and corresponding indicator lights
When a function is selected, the corresponding indicator
light will illuminate.
If the selected function is not compatible with the program-
med wash cycle, the corresponding indicator light will flash
and the function will not be activated.
If the selected function is not compatible with another
function which has been selected previously, the indicator
light corresponding to the first function selected will flash and
only the second function will be activated; the indicator light
corresponding to the enabled option will remain lit.
Door locked indicator light
When the indicator light is on, the porthole door is locked to
prevent it from being opened; make sure the indicator light is
off before opening the door (wait approximately 3 minutes).
To open the door during a running wash cycle, press the
START/PAUSEbutton;thedoormaybeopenedoncethe
DOOR LOCKED indicator light turns off.
Starting a wash cycle
1. SwitchthewashingmachineonbypressingtheON/OFFbutton.Allindicatorlightswillswitchonforafewseconds,then
theywillswitchoffandtheSTART/PAUSEindicatorlightwillpulse.
2. Load the laundry and close the door.
3.SettheWASHCYCLEknobtothedesiredprogramme.
4. Set the washing temperature (see “Personalisation”).
5. Set the spin speed (see “Personalisation”).
6. Measure out the detergent and washing additives (see “Detergents and laundry”).
7. Select the desired functions.
8.StartthewashcyclebypressingtheSTART/PAUSEbuttonandthecorrespondingindicatorlightwillremainlitinafixed
manner, in green.
Tocancelthesetwashcycle,pausethemachinebypressingtheSTART/PAUSEbuttonandselectanewcycle.
9.Attheendofthewashcyclethe END indicator light will switch on. The door can be opened once the DOOR LOCK
indicator light turns off (wait approximately 3 minutes). Take out your laundry and leave the appliance door ajar to make sure
the drum dries completely. Switch the washing machine off by pressing the ON/OFF button.
Wash
Rinse
Spin
Drain
End of wash cycle
8
GB
Wash cycles
Table of wash cycles
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors such as
water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
1) Test wash cycle in compliance with regulations 1061/2010: set wash cycle 15 with a temperature of 60°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments
which can be washed at 60°C. The actual washing temperature may differ from the indicated value.
2) Test wash cycle in compliance with regulations 1061/2010: set wash cycle 15 with a temperature of 40°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments
which can be washed at 40°C. The actual washing temperature may differ from the indicated value.
For all Test Institutes:
2) Long wash cycle for cottons: set wash cycle 15 with a temperature of 40°C.
3) Long programme for synthetics: set programme 4, then select the “
Extra Wash
” option.
* If you select programme 11 and exclude the spin cycle, the machine will drain only.
** The duration of the wash cycle can be checked on the display.
Wash cycles
Description of the wash cycle
Max.
temp. (°C)
Max.
speed
(rpm)
Detergents
Max.
load (kg)
Residual
dampness %
Energy
consumption
kWh
Total water lt
Cycle
duration
Pre-wash Wash
Fabric
softener
EVERYDAY FAST
1 Colour Mix 59’
40° 1000 -
6 - - - 59’
2 Cotton 59’
60° 1000 -
6 - - - 59’
3 Cotton 45’
40° 1000 -
3 - - - 45’
4 Synthetics 59’ (3)
40°
(Max. 60°)
1000 -
3 44 0,50 39 59’
5 Mix 30’
30° 800 -
3 70 0,17 31 30’
6 Express 20’
20° 800 -
3 - - - 20’
Special & Partial
7 Gym Kit
40° 600 -
3 - - - **
8 Sport Shoes
30° 600 -
Max. 2
pairs
- - - **
9
Baby: Heavily soiled delicate colours. 40° 800 -
2 - - - **
10 Rinse
- 1000 - -
6 - - - **
11 Spin + Drain
- 1000 - - - 6 - - - **
11 Only Drain *
-
- - - 6 - - - **
Dedicated
12
Duvet: for down-stuffed garments. 30° 1000 -
1,5 - - - **
13
Wool: for wool, cashmere, etc. 40° 800 -
1,5 - - - **
14
Silk/Curtains: for garments in silk and viscose, lingerie.
30° 0 -
1 - - - **
15
Eco Cotton 60° (1): heavily soiled whites and resistant colours. 60° 1000 -
6 62 1,02 49,8 195’
15
Eco Cotton 40° (2): lightly soiled whites and delicate colours. 40° 1000 -
6 62 0,86 76 185’
16
Cotton with prewash: extremely soiled whites. 90° 1000
6 - - - **
Fast daily cycles
Acompletesetoffastprogrammestowashthemostcommonlyusedfabrics-evenwithafullload-andtoremovethemost
frequent daily dirt in less than 1 hour.
Colour Mix 59’: to wash mixed and coloured items together.
Cotton 59’: cycle designed to wash cotton garments - mainly white items. It can be used with powder detergent too.
Cotton 45’: short cycle designed to wash delicate cotton items.
Synthetics 59’: specific for synthetic items. If the dirt is difficult to remove, the temperature can be increased up to 60° and
powder detergent can be used too.
Mix 30’: short cycle designed to wash a mixed load of cotton and synthetic fabrics - white and coloured items together.
Express 20’: this programme refreshes your items, making them perfumed again in just 20 minutes.
GB
9
Setting the temperature
TurntheTEMPERATUREknobtosetthewashtemperature(seeTable of wash cycles).
The temperature may be lowered, or even set to a cold wash .
The washing machine will automatically prevent you from selecting a temperature which is higher than the maximum value
set for each wash cycle.
! Exception: if the 4 programme is selected, the temperature can be increased up to a value of 60°C.
Setting the spin speed
Turn the SPIN SPEED knob to set the spin speed for the selected wash cycle.
The maximum spin speeds available for each wash cycle are as follows:
Wash cycles Maximum spin speed
Cottons 1000 rpm
Synthetics 1000 rpm
Wool 800 rpm
Silk drain only
The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol .
The washing machine will automatically prevent you from selecting a spin speed which is higher than the maximum speed
set for each wash cycle.
Functions
The various wash functions available with this washing machine will help to achieve the desired results, every time.
To activate the functions:
1. Press the button corresponding to the desired function;
2. the function is enabled when the corresponding indicator light is illuminated.
Note:
- If the selected function is not compatible with the programmed wash cycle, the corresponding indicator light will flash and
the function will not be activated.
- If the selected function is not compatible with another function which has been selected previously, the indicator light corre-
sponding to the first function selected will flash and only the second function will be activated; the indicator light corresponding
to the enabled option will remain lit.
Delay timer
To set a delayed start for the selected programme, press the corresponding button repeatedly until the required delay period
has been reached. When this option is enabled, the symbol lights up on the display. To remove the delayed start option
press the button until the text “OFF” appears on the display.
Extra Wash
Enable the
Extra Wash
option for very dirty items, where compatible. Press this option to let the cycle automatically re-adjust
all wash parameters through a longer lasting cycle. The option always leaves the temperature unchanged, while the spin cycle
is automatically brought back to maximum levels. The user can set the spin cycle back to the desired value at any time.
The option washes cotton and synthetic items, saving energy and helping the environment. Energy saving is due to
a cold wash cycle, while an enhanced mechanical action and optimised water use make it possible to reach the desired result.
Recommended for slightly soiled garments. Use of liquid detergent recommended.
Personalisation
10
GB
Detergents and laundry
Detergent dispenser drawer
Good washing results also depend on the correct dose of
detergent: adding too much detergent will not necessa-
rily result in a more efficient wash, and may in fact cause
build up on the inside of your appliance and contribute to
environmental pollution.
! Do not use hand washing detergents because these
create too much foam.
! Use powder detergent for white cotton garments, for pre-
washing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
Open the detergent di-
spenser drawer and pour
in the detergent or washing
additive, as follows.
compartment 1: Pre-wash detergent (powder)
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in immediately
prior to the start of the wash cycle.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
Note: If a “tablet detergent” is used, always follow the ma-
nufacturer’s instructions.
Preparing the laundry
•Dividethelaundryaccordingto:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
•Emptyallgarmentpocketsandcheckthebuttons.
•Donot exceed the values listed in the“Table of wash
cycles”, which refer to the weight of the laundry when dry.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
Special wash cycles
Gym Kit: cycle suitable to wash all sports items together,
including gym towels, while respecting their fibres (follow the
instructions in the garment labels).
Sport Shoes: is for washing sports shoes; for best results,
do not wash more than 2 pairs simultaneously.
We recommend fastening any strings before introducing the
shoes into the drum.
Baby: cycle designed for dirt typical of children’s garments
in that it effectively removes any traces of residual detergent.
Duvet: to wash single duvets (the weight of which should not
exceed 1,5 kg), cushions or clothes padded with goose down
such as puffa jackets, use the special wash cycle number 12.
We recommend that duvets are placed in the drum with their
edges folded inwards (see figure) and that no more than ¾
of the total volume of the drum is used. To achieve the best
results, we recommend that a liquid detergent is used and
placed inside the detergent dispenser drawer.
Wool: all wool garments can be washed using programme
13, even those carrying the “hand-wash only label. For
best results, use special detergents and do not exceed 1,5 kg
of laundry.
Silk: use special wash cycle 14 to wash all silk garments.
We recommend the use of special detergent which has been
designed to wash delicate clothes.
Curtains: fold curtains and place them in a pillow case or
mesh bag. Use wash cycle 14.
Load balancing system
Before every spin cycle, to avoid excessive vibrations and
to distribute the load in a uniform manner, the drum rotates
continuously at a speed which is slightly greater than the
washing rotation speed. If, after several attempts, the load
is not balanced correctly, the machine spins at a reduced
spin speed. If the load is excessively unbalanced, the
washing machine performs the distribution process instead
of spinning. To encourage improved load distribution and
balance, we recommend small and large garments are
mixed in the load.
1
2
3
GB
11
Troubleshooting
Yourwashingmachinecouldfailtowork.BeforecontactingtheTechnicalAssistanceCentre(see “Assistance”), make sure
that the problem cannot be not solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not
take in water (“H2O” will flash on
the display).
The washing machine continuously
takes in and drains water.
The washing machine does not
drain or spin.
The washing machine vibrates a lot
during the spin cycle.
The washing machine leaks.
The function indicator lights and
the start/pause indicator light flash,
while one of the phase in progress
indicator lights and the door locked
indicator light will remain lit in a fixed
manner.
There is too much foam.
Possible causes / Solutions:
•Theapplianceisnotpluggedintothesocketfully,orisnotmakingcontact.
•Thereisnopowerinthehouse.
•Thewashingmachinedoorisnotclosedproperly.
•TheON/OFFbuttonhasnotbeenpressed.
•TheSTART/PAUSEbuttonhasnotbeenpressed.
•Thewatertaphasnotbeenopened.
•Adelayedstarthasbeenset(see “Personalisation”).
•Thewaterinlethoseisnotconnectedtothetap.
•Thehoseisbent.
•Thewatertaphasnotbeenopened.
•Thereisnowatersupplyinthehouse.
•Thepressureistoolow.
•TheSTART/PAUSEbuttonhasnotbeenpressed.
•Thedrainhoseisnotfittedataheightbetween65and100cmfromthefloor
(see “Installation”).
•Thefreeendofthehoseisunderwater(see “Installation”).
•Thewalldrainagesystemisnotfittedwithabreatherpipe.
If the problem persists even after these checks, turn off the water tap, switch
theapplianceoffandcontacttheAssistanceService.Ifthedwellingisononeof
the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special
anti-draining valves are available in shops and help to avoid this inconvenience.
•Thewashcycledoesnotincludedraining:somewashcyclesrequirethedrain
phase to be started manually.
•Thedrainhoseisbent(see “Installation”).
•Thedrainageductisclogged.
•Thedrumwasnotunlockedcorrectlyduringinstallation(see “Installation”).
•Thewashingmachineisnotlevel(see “Installation”).
•Thewashingmachineistrappedbetweencabinetsandwalls(see “Installation”).
•Thewaterinlethoseisnotscrewedonproperly(see “Installation”).
•Thedetergentdispenserdrawerisblocked(forcleaninginstructions,see “Care
and maintenance”).
•Thedrainhoseisnotfixedproperly(see “Installation”).
•Switchoffthemachineandunplugit,waitforapproximately1minuteandthen
switch it back on again.
Iftheproblempersists,contacttheTechnicalAssistanceService.
•Thedetergentisnotsuitableformachinewashing(itshoulddisplaythetext
“for washing machines” or “hand and machine wash”, or the like).
•Toomuchdetergentwasused.
12
GB
Service
Before calling for Assistance:
• Check whether you can solve the problem alone (see “Troubleshooting”);
•Restarttheprogrammetocheckwhethertheproblemhasbeensolved;
•Ifthisisnotthecase,contactanauthorisedTechnicalAssistanceCentreusingthetelephonenumberprovidedonthe
guarantee certificate.
! Alwaysrequesttheassistanceofauthorisedtechnicians.
Have the following information to hand:
• thetypeofproblem;
• theappliancemodel(Mod.);
• theserialnumber(S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the
front of the appliance by opening the door.
13
DE
Deutsch
INHALTSVERZEICHNIS
Installation 14-15
Auspacken und Aufstellen
Wasser- und Elektroanschlüsse
Erster Waschgang
Technische Daten
Reinigung und Pflege 16
Abstellen der Wasser- und Stromversorgung
Reinigung des Gerätes
Reinigung der Waschmittelschublade
Pflege der Gerätetür und Trommel
Reinigung der Pumpe
Kontrolle des Wasserzulaufschlauchs
Vorsichtsmaßregeln und Hinweise 17
Allgemeine Sicherheit
Entsorgung
Beschreibung des Waschvollautomaten und
Starten eines Waschprogramms 18-19
Bedienblende
Kontrollleuchten
Starten eines Waschprogramms
Waschprogramme, 20
Programmtabelle
Schnelle Tageszyklen
Personalisierungen 21
Temperatureinstellung
Schleudereinstellung
Funktionen
Waschmittel und Wäsche 22
Waschmittelschublade
Vorsortieren der Wäsche
Besondere Wäscheteile
Unwuchtkontrollsystem
Störungen und Abhilfe 23
Kundendienst 24
DE
EWD 61051
Bedienungsanleitungen
WASCHVOLLAUTOMAT
14
DE
Installation
! Es ist äerst wichtig, diese Bedienungsanlei-
tung sorgltig aufzubewahren, um sie jederzeit
zu Rate ziehen zu nnen. Sorgen Sie dafür,
dass sie im Falle eines Umzugs oder einer Über-
gabe an einen anderen Benutzer das Gerät
stets begleitet, damit auch der neue Inhaber die
glichkeit hat, diese zu Rate zu ziehen.
! Lesen Sie die Hinweise bitte aufmerksam
durch, sie liefern wichtige Informationen hin-
sichtlich der Installation, des Gebrauchs und
der Sicherheit.
Auspacken und Aufstellen
Auspacken
1. Gerät auspacken.
2. Sicherstellen, dass der Waschvollautomat
keine Transportscden erlitten hat. Im Falle ei-
ner Beschädigung Gerät bitte nicht anschließen,
sondern den Kundendienst anfordern.
3. Die 3 Tran-
sportschutz-schrau-
ben herausschrau-
ben und die an der
Geräterückwand
befindlichen Distan-
zstücke aus Gummi
entfernen (siehe Ab-
bildung).
4. Die Öffnungen mittels der mitgelieferten
Abdeckungen verschliessen.
5. Sämtliche Teile aufbewahren: Sollte der
Waschautomat erneut transportiert werden,
müssen diese Teile wieder eingesetzt werden.
! Verpackungsmaterial ist kein Spielzeug für
Kinder.
Nivellierung
1. Der Waschvollautomat muss auf einem
ebenen, festen, schwingungsfreien Untergrund
aufgestellt werden ohne diesen an Wände, Mö-
bel etc. direkt anzulehnen.
2. Sollte der Boden
nicht perfekt eben
sein, müssen die
Unebenheiten durch
An- bzw. Ausdrehen
der vorderen Stellfüße
ausgeglichen werden
(siehe Abbildung), der
auf der Arbeitsfläche
zu ermittelnde Nei-
gungsgrad darf 2°
nicht überschreiten.
Eine präzise Nivellierung verleiht dem Gerät die
erforderliche Stabilität, durch die Vibrationen,
Betriebsgeräusche und ein Verrücken des
Gerätes vermieden werden. Bei Teppichböden
müssen die Stellfüße so reguliert werden, dass
ein ausreichender Freiraum zur Belüftung unter
dem Waschvollautomaten gewährleistet ist.
Wasser- und Elektroanschlüsse
Anschluss des Zulaufschlauches
1. Schrauben Sie den
Wasserschlauch an
einen Kaltwasserhahn
mit ¾-GAS-Gewinde-
anschluss an (siehe
Abb.). Lassen Sie
das Wasser vor dem
Anschluss so lange
auslaufen, bis klares
Wasser austritt.
2. Das andere Ende
des Schlauches an
den oben rechts am
Rückteil des Wasch-
vollautomaten befin-
dlichen Wasseran-
schluss anschließen
(siehe Abbildung).
3. Der Schlauch darf hierbei nicht eingeklemmt
oder abgeknickt werden.
! Der Wasserdruck muss innerhalb der Wer-
te liegen, die in der Tabelle der technischen
Daten angegeben sind (siehe nebenstehende
Seite).
! Sollte der Zulaufschlauch nicht lang genug
sein, dann wenden Sie sich bitte an einen
Fachhändler oder an einen autorisierten Fach-
mann.
! Verwenden Sie niemals bereits gebrauchte
Schläuche.
! Verwenden Sie die Schläuche, die mit dem
Gerät geliefert wurden.
15
DE
Anschluss des Ablaufschlauches
Schließen Sie den
Ablaufschlauch ohne
ihn dabei abzuknicken
an einen geeigneten
Abfluss an. Die Minde-
stablaufhöhe beträgt
65 - 100 cm (gemes-
sen vom Boden), oder
hängen Sie diesen
mittels des Schlau-
chhalters gesichert in
ein Becken oder Wanne ein;
Befestigen Sie diesen
mittels des mitgelie-
ferten Schlauchhal-
ters z.B. an einen
Wasserhahn (siehe
Abbildung). Das freie
Ablaufschlauchende
darf nicht unter Wa-
sser positioniert wer-
den.
! Verlängerungsschläuche sollten nicht einge-
setzt werden. Sollte dies unvermeidlich sein,
muss die Verlängerung denselben Durchmes-
ser des Originalschlauchs aufweisen und darf
eine Länge von 150 cm nicht überschreiten.
Stromanschluss
Vor Einfügen des Netzsteckers in die Steckdo-
se ist sicherzustellen, dass:
die Steckdose über eine normgerechte Erdung
verfügt;
• die Steckdose die in den Technischen Daten
angegebenen Höchstlast des Gerätes trägt
(siehe nebenstehende Tabelle);
die Stromspannung den in den Technischen
Daten angegebenen Werten entspricht (siehe
nebentehende Tabelle);
die Steckdose mit dem Netzstecker des
Waschvollautomaten kompatibel ist. An-
dernfalls muss der Netzstecker (oder die
Steckdose) ersetzt werden.
! Der Waschvollautomat darf nicht im Freien
installiert werden, auch nicht, wenn es sich
um einen geschützten Platz handelt. Es ist
gefährlich, das Gerät Gewittern und Unwettern
auszusetzen.
! Die Steckdose sollte nach installiertem Gerät
leicht zugänglich sein.
! Verwenden Sie bitte keine Verlängerungen
oder Mehrfachstecker.
! Das Netzkabel darf nicht gebogen bzw. ein-
geklemmt werden.
! Das Versorgungskabel darf nur durch autori-
sierte Fachkräfte ausgetauscht werden.
Achtung! Der Hersteller übernimmt keinerlei
Haftung, sollten diese Vorschriften nicht genau
beachtet werden.
Erster Waschgang
Lassen Sie nach der Installation bzw. vor
erstmaligem Gebrauch erst einen Waschgang
(mit Waschmittel) ohne Wäsche durchlaufen.
Stellen Sie hierzu das Waschprogramm 2 ein.
65 - 100 cm
Technische Daten
Modell
EWD 61051
Abmessun-
ge
Breite 59,5 cm
Höhe 85 cm
Tiefe 51,7 cm
Fassung-
svermögen
1 bis 6 kg
Elektroan-
schlüsse
siehe das am Gerät befindliche
Typenschild
Wasseran-
schlüsse
Höchstdruck 1 MPa (10 bar)
Mindestdruck 0,05 MPa (0,5 bar)
Trommelvolumen 46 Liter
Schleuder-
touren
bis zu 1000 U/min.
Prüfpro-
gramme
gemäß der
Richtlinien
1061/2010
und
1015/2010
Programm 15:
Eco Baumwolle 60°C.
Programm 15:
Eco Baumwolle 40°C.
Dieses Gerät entspricht den
folgenden EG-Richtlinien:
- 2004/108/CE (elektromagneti-
sche Verträglichkeit) und nach-
folgenden Änderungen
- 2012/19/EU - WEEE
- 2006/95/CE (Niederspannung)
16
DE
Reinigung und Pflege
Abstellen der Wasser- und Strom-
versorgung
Drehen Sie den Wasserhahn nach jedem
Waschvorgang zu. Hierdurch wird der Ver-
schleiß der Wasseranlage verringert und
Wasserlecks vorgebeugt.
Ziehen Sie den Netzstecker aus der
Steckdose, bevor Sie Ihren Waschvollauto-
maten reinigen.
Reinigung des Gerätes
Die Gehäuseteile und die Teile aus Gummi
können mit einem mit warmer Spülmittellauge
angefeuchteten Tuch gereinigt werden. Ver-
meiden Sie Löse- und Scheuermittel
Reinigung der Waschmittelschu-
blade
Heben Sie die Schu-
blade leicht an und
ziehen Sie sie nach
vorne hin heraus (sie-
he Abbildung).
Spülen Sie sie regel-
mäßig unter fließen-
dem Wasser gründlich
aus.
Pflege der Gerätetür und Trommel
Lassen Sie die Gerätetür stets leicht offen
stehen, um die Bildung unangenehmer
Gerüche zu vermeiden.
Reinigung der Pumpe
Ihr Gerät ist mit einer selbstreinigenden Pumpe
ausgerüstet, eine Wartung ist demnach nicht
erforderlich. Es könnte jedoch vorkommen,
dass kleine Gegenstände (Münzen, Knöpfe) in
die zum Schutz der Pumpe dienende Vorkam-
mer (befindlich unter der Pumpe) fallen.
! Vergewissern Sie sich, dass der Waschgang
abgeschlossen ist und ziehen Sie den Netz-
stecker heraus.
Zugang zur Vorkammer:
1. Nehmen Sie die
Abdeckung (befin-
dlich an der Geräte-
front) mit Hilfe eines
Schraubenziehers ab
(siehe Abbildung);
2. Drehen Sie den
Deckel gegen den
Uhrzeigersinn ab
(siehe Abbildung):
es ist ganz normal,
wenn etwas Wasser
austritt;
3. Reinigen Sie das Innere gründlich;
4. Schrauben Sie den Deckel wieder auf;
5. Bringen Sie die Abdeckung wieder an. Stel-
len Sie hierbei sicher, dass die Haken in die
Schlitze eingreifen, bevor Sie die Abdeckung
fest andrücken.
Kontrolle des Wasserzulau-
fschlauchs
Kontrollieren Sie den Zulaufschlauch min-
destens einmal im Jahr. Weist er Risse bzw.
Brüche auf, muss er ausgetauscht werden.
Der starke Druck während des Waschpro-
gramms könnte zu plötzlichem Platzen führen.
! Verwenden Sie niemals bereits gebrauchte
Schläuche.
17
DE
Vorsichtsmaßregeln und
Hinweise
! Der Waschvollautomat wurde nach den strengsten inter-
nationalen Sicherheitsvorschriften entworfen und gebaut.
Nachstehende Hinweise werden aus Sicherheitsgründen
geliefert und sollten aufmerksam gelesen werden.
Allgemeine Sicherheit
Dieses Gerät wurde ausschließlich für den Einsatz im priva-
ten Haushalt konzipiert.
Dieses Gerät darf von Kindern ab 8 Jahren
und von Personen mit eingeschränkten kör-
perlichen, sensorischen oder geistigen Fähi-
gkeiten oder mit unzureichender Erfahrung
und Kenntnis verwendet werden, vorausge-
setzt, sie werden überwacht oder sie haben
eine ausreichende Einweisung in die sichere
Nutzung des Geräts erhalten und haben die
damit verbundenen Gefahren verstanden.
Erlauben Sie Kindern nicht, mit dem Gerät zu
spielen. Wartung und Reinigung dürfen nicht
von unbeaufsichtigten Kindern ausgeführt
werden.
Der Waschvollautomat darf nur von Erwachsenen und geß
den Anleitungen dieses Handbuchs bedient werden.
Berühren Sie das Gerät nicht, wenn Sie barfuß sind, und
auch nicht mit nassen oder feuchten Händen oder Füßen.
Ziehen Sie den Gerätestecker nicht am Kabel aus der
Steckdose, sondern nur am Netzstecker selbst.
Öffnen Sie die Waschmittelschublade nicht, wenn das Gerät
in Betrieb ist.
Berühren Sie nicht das Ablaufwasser, es könnte sehr heiß
sein.
Öffnen Sie die Gerätetür nicht mit Gewalt: Der Sicherheits-
Schließmechanismus könnte hierdurch beschädigt werden.
Bei etwaigen Störungen versuchen Sie bitte nicht, Innenteile
selbst zu reparieren.
Halten Sie Kinder stets von dem in Betrieb befindlichen
Gerät fern.
Während des Waschgangs kann die Gerätetür sehr heiß
werden.
Muss das Gerät versetzt werden, sollten hierfür zwei oder
drei Personen verfügbar sein. Versetzen Sie es niemals
allein, das Gerät ist äußerst schwer.
Bevor Sie die sche einfüllen, stellen Sie bitte sicher, dass
die Wäschetrommel leer ist.
Entsorgung
Entsorgung des Verpackungsmaterials: Befolgen Sie die
lokalen Vorschriften, Verpackungsmaterial kann wiederver-
wertet werden.
Gemäß der Europäischen Richtlinie 2012/19/EU - WEEE
über Elektro- und Elektronik-Altgeräte dürfen Elektrohau-
shalts-Altgeräte nicht über den herkömmlichen Haushalts-
müllkreislauf entsorgt werden. Altgeräte müssen separat
gesammelt werden, um die Wiederverwertung und das
Recycling der beinhalteten Materialien zu optimieren
und die Einflüsse auf die Umwelt und die Gesundheit zu
reduzieren. Das Symbol durchgestrichene Mülltonne“
auf jedem Produkt erinnert Sie an Ihre Verpflichtung,
dass Elektrohaushaltsgeräte gesondert entsorgt werden
müssen. Endverbraucher können sich an Abfallämter der
Gemeinden wenden, um mehr Informationen über die kor-
rekte Entsorgung ihrer Elektrohaushaltsgeräte zu erhalten.
18
DE
Waschmittelschublade: für Waschmittel und Zusätze
(siehe „Waschmittel und Wäsche“).
Taste ON/OFF: Zum Ein- und Ausschalten Ihres Waschvol-
lautomaten.
Wählschalter PROGRAMME: Zur Wahl der Waschpro-
gramme. Während des Programmablaufs bleibt der Schalter
feststehend.
Tasten mit Kontrollleuchten FUNKTIONEN: Zur Einstellung
der verfügbaren Funktionen. Die der gewählten Einstellung
entsprechende Kontrollleuchte bleibt eingeschaltet.
Wählschalter SCHLEUDERN: oder um das Schleudern
auszuschliessen (siehe „Personalisierungen“).
hlschalter TEMPERATUREN: Zur Einstellung der Wa-
schtemperatur oder einer Kaltwäsche (siehe „Personalisie-
rungen“).
DISPLAY: zur Anzeige der Dauer der verschiedenen ver-
fügbaren Programme sowie der Restzeit nach Zyklusstart;
wurde eine STARTZEITVORWAHL eingestellt, dann wird die
bis zum Start des ausgewählten Programms verbleibende
Zeit angezeigt.
Taste STARTZEITVORWAHL : Zur Vorwahl der Startzeit
des gewählten Programms drücken Sie bitte diese Taste; Der
Wert wird auf dem Display angezeigt.
Kontrollleuchten PROGRAMMABLAUF: Zur Kontrolle des
Waschprogrammablaufs.
Die eingeschaltete Kontrollleuchte zeigt die laufende Pro-
grammphase an.
Kontrollleuchte GERÄTETÜR GESPERRT: Diese Taste
zeigt an, ob die Gerätetür geöffnet werden kann oder nicht
(siehe Nebenseite).
Taste mit Kontrollleuchte START/PAUSE: Mittels dieser
Taste werden die Waschprogramme gestartet oder kurz
unterbrochen.
NB: Durch Drücken dieser Taste, kann das Waschprogramm
zeitweilig unterbrochen werden (Pause). Die entsprechende
Kontrollleuchte schaltet auf orangefarbenes Blinklicht, die
Kontrollleuchte der bestehenden Programmphase dage-
gen schaltet auf Dauerlicht. Sobald die Kontrollleuchte
GERÄTETÜR GESPERRT erlischt, kann die Gerätetür
geöffnet werden (etwa 3 Minuten).
Um das Programm an der Stelle, an der es unterbrochen
wurde, wieder in Gang zu setzen, drücken Sie diese Taste
erneut.
Funktion Standby
Zur Erfüllung der neuen Richtlinien zum Energieverbrauch
ist diese Waschmaschine mit einem automatischen Aus-
schaltsystem (Standby) ausgestattet, das nach 30 Minuten
des Nichtgebrauchs in Funktion tritt. Drücken Sie kurz die
Taste EIN-AUS und warten Sie, bis sich die Maschine wieder
einschaltet.
Beschreibung des Waschvollautomaten
und Starten eines Waschprogramms
Kontrollleuchten
PROGRAMMABLAUF
Kontrollleuchte
GERÄTETÜR
GESPERRT
Taste mit
Kontrollleuchte
START/
PAUSE
Bedienblende
Waschmittelschublade
Taste
ON/OFF
Wählschalter
PROGRAMME
Wählschalter
TEMPERATUREN
Wählschalter
SCHLEUDERN
DISPLAY
Tasten mit
Kontrollleuchten
FUNKTIONEN
Taste
STARTZEIT-
VORWAHL
19
DE
Kontrollleuchten
Die Kontrollleuchten liefern wichtige Hinweise.
Sie signalisieren:
Laufende Programmphase
Wurde das Waschprogramm gewählt und gestartet,
leuchten die Kontrollleuchten nach und nach auf, und
zeigen so den jeweiligen Programmstand an.
Funktionstasten und entsprechende Kontroll-
leuchten
Nach der Wahl einer Funktion leuchtet die entsprechen-
deTaste auf. Ist die gewählte Funktion nicht vereinbar mit
dem eingestellten Programm, schaltet die entsprechende
Kontrollleuchte auf Blinklicht und die Funktion wird nicht
aktiviert. Ist die gewählte Funktion mit einer anderen bereits
eingestellten nicht kompatibel, schaltet die der ersten
Funktion entsprechende Kontrollleuchte auf Blinklicht und
nur die zweite Funktion wird aktiviert, die Kontrollleuchte der
aktivierten Funktion schaltet auf Dauerlicht.
Kontrollleuchte Gerätetür gesperrt:
Ist diese Kontrollleuchte eingeschaltet, bedeutet dies,
dass das Bullauge gesperrt ist; warten Sie, bis die Leuchte
erlischt, um das Bullauge zu öffnen (etwa 3 Minuten). Um
während eines laufenden Programms das Bullauge zu
öffnen, drücken Sie die Taste START/PAUSE; ist die der
GERÄTETÜR GESPERRT entsprechende Kontrollleuchte
ausgeschaltet, kann das Bullauge geöffnet werden.
Starten eines Waschprogramms
1. Schalten Sie den Waschvollautomaten durch Drücken der ON/OFF-Taste ein. Sämtliche Kontrollleuchten leuchten für eini-
ge Sekunden auf, und erlöschen wieder. Die Kontrollleuchte START/PAUSE schaltet auf Blinklicht.
2. Füllen Sie die Wäsche ein, und schließen Sie die Gerätetür.
3. Stellen Sie mittels des Wählschalters PROGRAMME das gewünschte Programm ein.
4. Stellen Sie die Waschtemperatur ein (siehe „Personalisierungen“).
5. Stellen Sie die Schleuderstufe ein (siehe „Personalisierungen“).
6. Füllen Sie Waschmittel und Zusätze ein (siehe „Waschmittel und Wäsche“).
7. Wählen Sie die gewünschten Funktionen.
8. Setzen Sie das Programm in Gang. Drücken Sie hierzu die Taste START/PAUSE. Die entsprechende Kontrollleuchte bleibt
eingeschaltet (grünes Dauerlicht). Um die Waschprogramm-Einstellung rückgängig zu machen, muss das Gerät auf Pause
geschaltet werden. Drücken Sie hierzu die Taste START/PAUSE. Wählen Sie daraufhin das neue Programm.
9. Nach Ablauf des Waschprogramms leuchtet die Kontrollleuchte END auf. Sobald die Kontrollleuchte GERÄTETÜR GE-
SPERRT erlischt, kann das Bullauge geöffnet werden (etwa 3 Minuten). Nehmen Sie die Wäsche aus der Maschine und
lassen Sie die Gerätetür leicht offen stehen, damit die Trommel trocknen kann. Schalten Sie den Waschvollautomaten durch
Drücken der ON/OFF-Taste aus.
Hauptwäsche
Spülen
Schleudern
Abpumpen
Ende des Waschgangs
20
DE
Waschprogramme
Programmtabelle
Wasch-programme
Beschreibung des Programms
Max.
Temp.
(C°)
Max.
Schleuder
Geschwin-
digkeit
(U/min)
Waschmittel
Max.
Beladungsmenge
(kg)
Restfeuchtigkeit %
Energieverbrauch
kWh
Wasser gesamt lt
Programmdauer
Vorwäsche
Hauptwä-
sche
Weich-
spüler
TÄGLICH SCHNELL
1 Buntwäsche 59’
40° 1000 -
6 - - - 59’
2 Baumwolle 59’
60° 1000 -
6 - - - 59’
3 Baumwolle 45’
40° 1000 -
3 - - - 45’
4 Synthetik 59’ (3)
40°
(Max. 60°)
1000 -
3 44 0,50 39 59’
5 Mix 30’
30° 800 -
3 70 0,17 31 30’
6 Express 20’
20° 800 -
3 - - - 20’
Spezial
7 Sportwäsche
40° 600 -
3 - - - **
8 Sportschuhe
30° 600 -
Max.
2 Paar
- - - **
9 Baby
40° 800 -
2 - - - **
10 Spülen
- 1000 - -
6 - - - **
11 Schleudern + Abpumpen
- 1000 - - - 6 - - - **
11 Nur abpumpen *
- - - - 6 - - - **
Extra
12 Daunen: wäsche- bzw. Kleidungsstücke mit Daunenfüllung.
30° 1000 -
1,5 - - - **
13 Wolle: wolle, Kaschmir usw.
40° 800 -
1,5 - - - **
14 Seide+Vorhänge: kleidungsstücke aus Seide, Viskose und Feinwäsche.
30° 0 -
1 - - - **
15
Eco Baumwolle 60° (1): stark verschmutzte Weiß- und farbechte
Buntsche.
60° 1000 -
6 62 1,02 49,8 195’
15
Eco Baumwolle 40° (2): leicht verschmutzte Weiß- und emp ndliche
Buntwäsche.
40° 1000 -
6 62 0,86 76 185’
16 Baumwolle Vorwäsche: stark verschmutzte Kochwäsche.
90° 1000
6 - - - **
Die auf dem Display und in der Bedienungsanleitung genannte Zyklusdauer wird ausgehend von Standardbedingungen berechnet. Die effektiv benötigte Zeit kann aufgrund zahlreicher Faktoren wie Tempe-
ratur und Druck des Zulaufwassers, Raumtemperatur, Waschmittelmenge, Art, Menge und Verteilung der Waschladung sowie der gewählten Zusatzfunktionen variieren.
1) Prüfprogramm gemäß 1061/2010: Programm 15 und eine Temperatur von 60°C einstellen.
Dieser Zyklus ist für den Waschvorgang von normal schmutziger Baumwollwäsche geeignet; es ist der wirksamste in Bezug auf den kombinierten Energie-Wasser-Ver-
brauch; für bei 60°C zu waschende Wäsche zu verwenden. Die effektive Waschtemperatur kann von der angegebenen abweichen.
2) Prüfprogramm gemäß 1061/2010: Programm 15 und eine Temperatur von 40°C einstellen.
Dieser Zyklus ist für den Waschvorgang von normal schmutziger Baumwollwäsche geeignet; es ist der wirksamste in Bezug auf den kombinierten Energie-Wasser-Ver-
brauch; für bei 40°C zu waschende Wäsche zu verwenden. Die effektive Waschtemperatur kann von der angegebenen abweichen.
Für alle Testinstitute:
2) Langes Baumwollprogramm: Programm 15 und eine Temperatur von 40°C einstellen.
3) Programm Kunstfasern lang: das Programm 4 einstellen, dann die Option “
Extra Wash
” auswählen.
Schnelle Tageszyklen
Ein komplettes Set schneller Programme für die Wäsche der täglichen Verschmutzung in weniger als 1 Stunde der meist ge-
brauchten Fasern auch bei voller Waschfüllung.
Buntwäsche 59’: zum Waschen von Mischwäsche und Buntwäsche zusammen.
Baumwolle 59’: spezieller Zyklus für überwiegend weiße Baumwolle. Kann auch mit Waschmittel in Pulverform verwendet werden.
Baumwolle 45’: kurzer Zyklus für Baumwoll-Feinwäsche.
Synthetik 59’: spezifisch für die Wäsche von Kunstfasern. Bei hartnäckigerer Verschmutzung kann die Temperatur bis 60°
erhöht werden und man kann ein Waschmittel in Pulverform verwenden.
Mix 30’: kurzer Zyklus für gemischte Wäsche aus Baumwolle und Kunstfaser, weiß und bunt zusammen.
Express 20’: das Programm frisch ihre Wäsche auf und verleiht ihr einen frischen Duft in nur 20 Minuten.
* Bei Auswahl des Programms 11 und Ausschluss der Schleuder, führt die Maschine nur den abpumpen aus.
** Die Programmdauer kann auf dem Display abgelesen werden.
1 / 1

Indesit EWD 61051 W EU Manualul utilizatorului

Categorie
Mașini de spălat
Tip
Manualul utilizatorului