McCulloch B33 PS4in1 Kit Manualul proprietarului

Tip
Manualul proprietarului

Acest manual este potrivit și pentru

B33 PS, B33 PS+
EN Operator's manual 10-26
BG Ръководство за експлоатация 27-45
BS Korisnički priručnik 46-62
CS Návod k použití 63-79
DA Brugsanvisning 80-96
DE Bedienungsanweisung 97-115
EL Οδηγίες χρήσης 116-134
ES Manual de usuario 135-152
ET Kasutusjuhend 153-168
FI Käyttöohje 169-184
FR Manuel d'utilisation 185-203
HR Priručnik za korištenje 204-220
HU Használati utasítás 221-237
IT Manuale dell'operatore 238-255
LT Operatoriaus vadovas 256-272
LV Lietošanas pamācība 273-289
NL Gebruiksaanwijzing 290-307
NO Bruksanvisning 308-324
PL Instrukcja obsługi 325-342
PT Manual do utilizador 343-360
RO Instrucţiuni de utilizare 361-378
RU Руководство по эксплуатации 379-397
SK Návod na obsluhu 398-414
SL Navodila za uporabo 415-431
SR Priručnik za rukovaoca 432-448
SV Bruksanvisning 449-464
TR Kullanım kılavuzu 465-481
UK Посібник користувача 482-500
B33BCSMC
1
2 3 4 5 6 7
8
5
0
FT
1
5
m
50F
T
15 m
9 10 11 12 13
14 15 16 17 18 19
20 21 22
23 24
25 26
27 28
1
2
3
29 30
31 32
33 34
D
E
F
C
B
A
35
F
E
A
B
C
D
36
37 38
39 40
41 42
43 44
45 46
47 48
49 50
51
2
1
52
53
A
54
55 56
57 58
59
6,0 m
18'
3,05 m
9'
2,0-2,4 mm
.079-.095"
10 cm
4"
60
61 62
6"
15 cm
63 64
"Click"
65 66
67 68
69 70
71 72
73 74
75
A
B
C
76
A
B
B
77
Contents
INTRODUCTION.......................................................... 10
SAFETY........................................................................11
ASSEMBLY..................................................................16
OPERATION................................................................ 17
MAINTENANCE........................................................... 18
TRANSPORTATION AND STORAGE.........................22
TECHNICAL DATA...................................................... 22
ATTACHMENTS.......................................................... 23
CONTENTS OF THE EC DECLARATION OF
CONFORMITY..............................................................25
INTRODUCTION
Operator's manual
The initial language of this operator's manual is English.
Operator's manuals in other languages are translations
from English.
Overview
(Fig. 1)
1. Assist handle
2. Suspension ring
3. Stop switch
4. Shaft coupling
5. Throttle trigger
6. Throttle lockout
7. Grass trimmer and brushcutter attachment
8. Combination tool
9. Muffler
10. Starter rope handle
11. Fuel tank cap
12. Spark plug/spark plug cap
13. Choke control
14. Air filter cover
15. Hex wrench
16. Harness
17. Cutting attachment guard for trimmer and
brushcutter attachment
18. Hedge trimmer blades
19. Angle adjustment lever
20. Guide bar
21. Saw chain
22. Cap for the chain oil tank
23. Sprocket cover
24. Wrench, 8 mm / 10 mm
25. Extended hedge trimmer attachment
26. Pole saw attachment
27. Guide bar cover for pole saw attachment)
28. Blade guard for extended hedge trimmer attachment
29. Nut
30. Support cup
31. Bottom holder
32. Grass blade
33. Trimmer head
34. Transport guard for grass blade
35. Operator's manual
36. Air purge bulb
37. Top holder
Symbols on the product
(Fig. 2) Warning
(Fig. 3) Read this manual
(Fig. 4) Wear approved head protection, hearing
protection and eye protection.
(Fig. 5) Wear approved protective gloves.
(Fig. 6) Use heavy-duty slip-resistant boots.
(Fig. 7) The product can cause objects to eject,
which can cause injury.
(Fig. 8) Maximum speed of the output shaft.
(Fig. 9) Safe distance
(Fig. 10) Safe distance
(Fig. 11) Risk of blade thrust if the cutting equipment
touches an object that it does not
immediately cut. The product can cut off
body parts. Keep a minimum of 15 m (50 ft)
distance to persons and animals during
operation of the product.
(Fig. 12) Make sure that long hair is put up above
your shoulders.
(Fig. 13) The arrows show the limits for the position of
the handle.
10 860 - 001 - 28.10.2018
(Fig. 14) Primer bulb
(Fig. 15) Choke control
(Fig. 16) Keep all parts of your body away from the
hot surfaces.
(Fig. 17) Make sure no person is within the kickback
danger zone.
(Fig. 18) DANGER - Keep hands away from blade.
(Fig. 19) Sound power level
(Fig. 20) The product agrees with the applicable EC
directives.
(Fig. 21) The product agrees with the applicable EAC
directives.
(Fig. 22) The product agrees with the applicable
Ukraine directives.
Note: Other symbols/decals on the product refer to
certification requirements for other commercial areas.
EU V
WARNING: Tampering with the engine
voids the EU type-approval of this product.
Product liability
As referred to in the product liability laws, we are not
liable for damages that our product causes if:
the product is incorrectly repaired.
the product is repaired with parts that are not from
the manufacturer or not approved by the
manufacturer.
the product has an accessory that is not from the
manufacturer or not approved by the manufacturer.
the product is not repaired at an approved service
center or by an approved authority.
SAFETY
Safety definitions
The definitions below give the level of severity for each
signal word.
WARNING: Injury to persons.
CAUTION: Damage to the product.
Note: This information makes the product easier to use.
Vibration safety
This product is for occasional operation only.
Continuous or regular operation of the product can
cause “white finger” or equivalent medical problems
from vibrations. Examine the condition of your hands
and fingers if you operate the product continuously or
regularly. If your hands or fingers have discoloration,
have pain, tingle, or are numb, stop work and speak to a
physician immediately.
General safety instructions
WARNING: Read the warning instructions
that follow before you use the product.
Use the product correctly. Injury or death is a
possible result of incorrect use. Only use the product
for the tasks found in this manual. Do not use the
product for other tasks.
Obey the instructions in this manual. Obey the safety
symbols and the safety instructions. If the operator
does not obey the instructions and the symbols,
injury, damage or death is a possible result.
Do not discard this manual. Use the instructions to
assemble, to operate and to keep your product in
good condition. Use the instructions for correct
installation of attachments and accessories. Only
use approved attachments and accessories.
Do not use a damaged product. Obey the
maintenance schedule. Only do the maintenance
work that you find an instruction about in this
manual. An approved service center must do all
other maintenance work.
This manual cannot include all situations that can
occur when you use the product. Be careful and use
your common sense. Do not operate the product or
do maintenance on the product if you are not sure
about of the situation. Speak to a product expert,
your dealer, service agent or approved service
center for information.
Disconnect the spark plug cable before you
assemble the product, put the product into storage or
do maintenance.
Do not use the product if it is changed from its initial
specification. Do not change a part of the product
without approval from the manufacturer. Only use
parts approved by the manufacturer. Injury or death
is a possible result of incorrect maintenance.
Do not breathe in the fumes from the engine. Long-
term inhalation of the engine's exhaust fumes is a
health risk.
860 - 001 - 28.10.2018
11
Do not start the product indoors or near flammable
material. The exhaust fumes are hot and can contain
a spark which can start a fire. Not sufficient airflow
can cause injury or death because of asphyxiation or
carbon monoxide.
When you use this product the engine makes an
electromagnetic field. The electromagnetic field can
cause damage to medical implants. Speak to your
physician and medical implant manufacturer before
you operate the product.
Do not let a child operate the product. Do not let a
person without knowledge of the instructions operate
the product.
Make sure that you always monitor a person, with
decreased physical capacity or mental capacity, that
uses the product. A responsible adult must be there
at all times.
Lock the product in an area that children and
unapproved persons cannot access.
The product can eject objects and cause injuries.
Obey the safety instructions to decrease the risk of
injury or death.
Do not go away from the product when the engine is
on.
The operator of the product is responsible if an
accident occurs.
Make sure that parts are not damaged before you
use the product.
Make sure that you are at minimum 15 m (50 ft)
away from other persons or animals before you use
the product. Make sure that persons in the adjacent
area know that you will use the product.
Refer to national or local laws. They can prevent or
decrease the operation of the product in some
conditions.
Do not use the product if you are fatigued or
influenced by alcohol, drugs or medicine. They can
have effects on your vision, alertness, coordination
or judgment.
General safety instructions for the
grass trimmer
Use the trimmer head to cut grass.
Always make sure the trimmer line is wound tightly
and equally around the drum to prevent harmful
vibration.
Only use recommended trimmer heads and trimmer
lines.
Make sure that the cutter on the trimmer guard is not
damaged. This cuts the trimmer line to the correct
length.
Operate the product with the cutting attachment
below your waist.
Do not touch the bevel gear after the engine stops.
The bevel gear is hot after the engine stops. Hot
areas can cause injury.
To trim the grass
1. Hold the trimmer head immediately above the
ground at an angle. Do not push the trimmer line into
the grass. (Fig. 23)
2. Decrease the engine speed to decrease the risk of
damage to plants.
3. Use 80 % throttle when you cut grass near objects.
(Fig. 24)
To cut the grass
1. Make sure that the grass trimmer line is parallel to
the ground when you cut. (Fig. 25)
2. Do not push the trimmer head to the ground. The
ground and the product can be damaged.
3. Do not let the trimmer head touch the ground
continuously, it can cause damage to the trimmer
head.
4. Use full throttle when you move the product from
side to side to cut grass. Make sure that the grass
trimmer line is parallel to the ground. (Fig. 26)
To sweep the grass
The airflow from the rotating trimmer line can be used to
remove cut grass from an area.
1. Hold the trimmer head and its trimmer line parallel to
the ground and above the ground.
2. Apply full throttle.
3. Move the trimmer head from side to side and sweep
the grass.
WARNING:
Clean the trimmer head cover
each time you assemble new trimmer line to
prevent unbalance and vibrations in the
handles. Also do a check of the other parts
of the trimmer head and clean it if
necessary.
General safety instructions for the
brushcutter
A grass blade is used for all types of tall or coarse
grass.
Grass blades and grass cutters must not be used on
woody stems.
Use head protection when you operate a product
with a blade.
Wear protective gloves when you touch the blade or
do maintenance.
Use the product with an approved blade. Do not use
a blade without correct installation of all necessary
parts. Make sure that the installation is done
correctly and that the correct parts are used.
Incorrect installation may cause the blade to fly off
and cause serious injury the operator or bystanders.
Operate the product with the cutting attachment
below your waist.
12
860 - 001 - 28.10.2018
Do not touch the bevel gear after the engine stops.
The bevel gear is hot after the engine stops. Hot
areas can cause injury.
A blade can cause injury when it turn after the
engine is stopped or the throttle trigger is released.
Keep hands away from blade. To touch the blade
can cause serious injury.
Stop the engine before you do work on the cutting
attachment. Make sure the cutting attachment fully
stops. Disconnect the lead from the spark plug.
Make sure that the blade has fully stopped to turn
before maintenance.
Keep the teeth of the blade correctly sharpened.
An incorrectly sharpened or damaged blade
increases the risk of accidents. Keep the teeth of the
blade correctly sharpened. Follow the instructions
and use the recommended file gauge.
Make sure that the blade guard is not damaged or
twisted.
Attach the transport guard to the blade before
transportation or storage of the product.
Blade thrust
A blade thrust is a sudden movement of the product
to the side, forward or rearward. A blade thrust
occurs when the grass blade or saw blade hits an
object that cannot be cut. In areas where it is not
easy to see the material being cut the risk of blade
thrust increases.
When a blade thrust occurs, there is a risk that the
product or the operator moves out of position. A
blade that moves can hit bystanders and there is a
risk of injuries.
If a blade is bent, has cracks, is broken or damaged,
discard the blade.
Use a sharp blade. The risk of blade thrust increases
when a blade is not sharp.
To clear grass with a grass blade
1. Keep your feet apart during operation of the product.
Make sure feet are tightly against the ground.
2. Put the support cup lightly on the ground. This
prevents the blade from touching the ground.
3. Use a sideway movement from right to left for a clear
stroke. Use the left side of the blade (between 8 and
12 o'clock) to cut. (Fig. 27)
4. Angle the blade to the left when you clear grass.
Note:
The grass collects easily in a line.
5. Use a sideway movement from left to right for the
return stroke.
6. Do the work rhythmically.
7. Move forward and keep feet tightly against the
ground.
8. Stop the engine.
9. Remove the product from the clip on the harness.
10. Put the product on the ground.
11. Collect the cut material.
General safety instructions for the
pole saw
More protective equipment for head, hands, legs and
feet is recommended. Correct protective clothing can
decrease injury caused by flying debris or accidental
touch with the saw chain.
When you cut with the product, do not lift your arms
above your shoulders. Do not stay below the
branches that are cut.
Always use gloves when you touch the chain.
Replace the guide bar and the chain immediately if it
is damaged, broken or removed.
Do not start the engine with the guide bar in a cut.
Remove the guide bar from the cut before you start
the engine.
Do not use the product to cut down trees or the tree
trunk.
Do not cut small brush and saplings with the product.
Do not let the chain touch objects when you start the
engine.
Be careful of overhead power lines.
Do not apply pressure on the product when you
complete a cut.
When you complete a cut, always release the throttle
trigger and let the engine operate at the idle speed.
Only cut the limbs or branches with less than 15 cm
(6 in.) in diameter above your head.
Hold the product tightly with your two hands to keep
the product balance.
(Fig. 28)
Operate the product slowly and cut carefully
Be careful of the direction in which the branch falls.
Be careful of the springpoles when you cut.
Springpoles are small limbs which can catch the
chain and decrease balance or control.
Be careful of the springback when the tension in the
wood releases.
Operate the product in a clear area. Frequently clean
fallen branches from the area to prevent injuries.
Cut long branches in pieces when you remove them.
Stop the engine, remove the harness and put the
machine on the ground before you start to collect the
cut material.
Attach the guide bar cover during transportation and
storage of the product.
Make sure that the guide bar cover is not damaged
or twisted.
To cut with the pole saw
WARNING: Do not cut with the product in
the rearward or forward direction.
860 - 001 - 28.10.2018 13
1. Set the product to the full throttle and apply a light
pressure.
2. Cut for the first time 15 cm (6 in.) away from the
trunk. Cut 1/3 through the bottom of the limb. (Fig.
29)
3. Move the pole saw 5-4 cm (2-4 in.) out on the limb.
Cut for the second time fully through the limb. (Fig.
29)
4. Cut for the third time. Do not cut too near it can injury
the tree.
Note: When you cut for the second and third time,
put the product against the limb to keep the branch
stable.
(Fig. 30)
General safety instructions for the
extended hedge trimmer
Keep hands away from blade. To touch the blade
can cause serious injury.
Keep all parts of the body away from the cutter
blade. Do not remove cut material or hold material to
be cut when the blades turn. Make sure to stop the
product before you clean or do maintenance. Blades
coast after turn off. Inattention during operation of
the product can cause serious injury.
When you cut with the product, do not lift your arms
above your shoulders. Do not stay below the
branches that are cut.
Hold the product as near to your body as possible for
the correct balance.
(Fig. 31)
Move the product from the bottom up when you cut
the sides.
(Fig. 32)
Do not cut too quickly. Cut slowly and continuously
until you get a good quality cut.
Make sure that the point of the blade does not touch
the ground.
Be careful of overhead power lines.
When you complete a cut, always release the throttle
trigger and let the engine operate at the idle speed.
Hold the hedge trimmer by the handle with the cutter
blade stopped. Hold the product correctly during
operation to decrease injury from the cutter blades.
Stop the engine, remove the harness and put the
machine on the ground before you start to collect the
cut material.
Attach the blade guard during transportation and
storage of the product.
Make sure that the blade guard is not damaged or
twisted.
To adjust the angle of the cutting blades
1. Push the lever to unlock. (Fig. 33)
2. Adjust the angle of the blades to the correct position.
3. Release the lever.
Safety instructions for operation
Make sure that the product is fully assembled before
operation.
Before a start, move the product 3 m (10 ft) away
from the position where you filled the fuel tank. Put
the product on a flat surface. Make sure that the
cutting attachment does not touch the ground or
other objects.
The product can cause objects to eject, which can
cause damage to the eyes. Always use an approved
eye protection when you operate the product.
Be careful, a child can come near the product
without your knowledge during operation.
Do not operate the product if there are persons in
the work area. Stop the product if a person goes into
the work area.
Make sure that you are always in control of the
product.
Do not use the product if you cannot receive aid if an
accident occurs. Always make sure others know you
will operate the product before you start to operate
the product.
Do not turn with the product before you make sure
that no persons or animals are in the safety area.
Remove all unwanted materials from the work area
before you start. If the cutting attachment hits an
object, the object can eject and cause injury or
damage. Unwanted material can wind around the
cutting attachment and cause damage.
Do not use the product in bad weather, such as fog,
rain, strong winds, risk of lightning or other weather
conditions. Dangerous conditions, such as slippery
surfaces, can occur because of bad weather.
Make sure that you can move freely and work in a
stable position.
Make sure that you cannot fall when you use the
product. Do not tilt when you operate the product.
Always hold the product with your two hands. Hold
the product on the right side of your body.
Operate the product with the cutting attachment
below your waist.
If the choke control is in the choke position when the
engine starts, the cutting attachment starts to turn.
Do not touch the bevel gear after the engine stops.
The bevel gear is hot after the engine stops. Hot
areas can cause injury.
Stop the engine before you move the product.
Do not put down the product with the engine on.
Before you remove the unwanted materials from the
product, stop the engine and wait until the cutting
attachment stops. Let the cutting attachment stop
before you or an aid remove the cut material.
14
860 - 001 - 28.10.2018
Personal protective equipment
WARNING: Read the warning instructions
that follow before you use the product.
Always use correct personal protective equipment
when you operate the product. The personal
protective equipment does not erase the risk of
injury. The personal protective equipment decreases
the grade of injury if an accident occurs.
Always use an approved eye protection while you
operate the product.
Do not operate the product with bare feet or with
open shoes. Always use heavy-duty slip-resistant
boots.
Use heavy, long pants.
If it is necessary, use approved protective gloves.
Use a helmet if it is possible that objects fall on your
head.
Always use approved ear protection while you
operate the product. Noise for a long period can
cause noise-induced hearing loss.
Make sure that you have a first aid kit near.
Safety devices on the product
WARNING: Read the warning instructions
that follow before you use the product.
Do not use a product with defective safety devices.
Do a check of the safety devices regularly. If the
safety devices are defective, speak to your
McCulloch service agent.
Throttle trigger lockout
The throttle trigger lockout locks the throttle trigger.
Push the throttle trigger lockout to release the throttle
trigger. When you release the handle, the throttle trigger
lockout and the throttle trigger go back to their initial
positions.
1. Make sure that the throttle trigger is locked at idle
when you release the throttle trigger lockout.
2. Push the throttle trigger lockout and make sure that it
goes back to its initial position when you release it.
3. Push the throttle trigger and make sure that it goes
back to its initial position when you release it.
Start the engine, and then apply full throttle. Release the
throttle trigger and examine if the cutting attachment
stops. If the cutting attachment turns with the throttle in
the idle position, examine the idle adjustment screw of
the carburetor.
To do a check of the stop switch
The stop switch stops the engine.
1. Start the engine.
2. Make sure that the engine stops when you move the
stop switch to the stop position.
Cutting attachment guard
The cutting attachment guard prevents a loose object to
eject in the direction of the operator.
Examine the cutting attachment guard for damage and
replace if it is damaged. Only use the approved guard
for the cutting attachment.
Harness release function
WARNING: Do not use the harness if the
release function is defective. Make sure that
the harness release function operates
correctly when you adjust the product.
The harness release function is at the front of the
product.
(Fig. 34)
The harness straps must always stay at the correct
position.
In an emergency, the harness release function helps
you to safely release from the product.
Muffler
Do not use an engine with a damaged muffler. A
damaged muffler increases the noise level and the
risk of fire. Keep a fire extinguisher near.
Examine regularly that the muffler is attached to the
product.
Do not touch the engine or the muffler when then
engine is on. Do not touch the engine or the muffler
for a while after the engine stops. Hot surfaces can
cause injuries.
A hot muffler can cause a fire. Be careful, if you use
the product near flammable liquids or fumes.
Do not touch the parts in the muffler, if the muffler is
damaged. The parts can contain some carcinogenic
chemicals.
Fuel safety
Do not start the product if there is fuel or engine oil
on the product. Remove the unwanted fuel/oil and let
the product dry. Remove unwanted fuel from the
product.
If you spill fuel on your clothing, change clothing
immediately.
Do not get fuel on your body, it can cause injury. If
you get fuel on your body, use a soap and water to
remove the fuel.
Do not start the engine if you spill oil or fuel on the
product or on your body.
Do not start the product if the engine has a leak.
Examine the engine for leaks regularly.
Be careful with fuel. Fuel is flammable and the fumes
are explosive and can cause injuries or death.
860 - 001 - 28.10.2018
15
Do not breathe in the fuel fumes, it can cause injury.
Make sure that there is a sufficient airflow.
Do not smoke near the fuel or the engine.
Do not put warm objects near the fuel or the engine.
Do not add the fuel when the engine is on.
Make sure that the engine is cool before you refuel.
Before you refuel, open the fuel tank cap slowly and
release the pressure carefully.
Do not add fuel to the engine in an indoor area. Not
sufficient airflow can cause injury or death because
of asphyxiation or carbon monoxide.
Tighten the fuel tank cap carefully or a fire can
occur.
Move the product at a minimum of 3 m (10 ft) from
the position where you filled the tank before a start.
Do not put too much fuel in the fuel tank.
Make sure that a leak cannot occur when you move
the product or fuel container.
Do not put the product or a fuel container where
there is an open flame, spark or pilot light. Make
sure that the storage area does not contain an open
flame.
Only use approved containers when you move the
fuel or put the fuel into storage.
Empty the fuel tank before long-term storage. Obey
the local law on where to dispose fuel.
Clean the product before long-term storage.
Remove the spark plug cable before you put the
product into storage to make sure that the engine
does not start accidentally.
General safety instructions for
maintenance
The operator of the product is responsible for the
performance of all necessary maintenance, as
specified in the operator's manual. Injury or death is
a possible result of incorrect maintenance.
Make sure that you regularly do the maintenance to
the product. The life of the product increases. The
risk of accidents decreases.
Make sure that you obey the maintenance schedule.
The intervals are calculated from daily use of the
product. The intervals are different if you do not use
the product each day.
Only do the maintenance work that you find an
instruction about in this manual. An approved service
center must do all other maintenance work.
Have all product servicing done by an approved
dealer, not including the tasks in
MAINTENANCE on
page 18
.
Let an approved dealer or an approved service
center regularly examine the product to do
adjustments or repairs.
Make sure the product is correctly assembled.
Do not use the product if it is changed from its initial
specification.
Do not change a part of the product without approval
from the manufacturer.
Only use parts approved by the manufacturer.
Examine for broken or incorrectly aligned parts, and
parts that do not move freely. Examine for other
conditions that can have an effect on the operation
of the product.
Do not use a damaged product. Replace or repair
damaged components.
Keep caps and fasteners correctly tightened.
Replacement components that are not approved or
the removal of safety devices can cause damage to
the product. This can also cause possible injury to
the operator or bystanders.
Only use accessories and replacement parts as
recommended. Do not change your product.
Keep handles dry, clean, and free from oil and
grease. Greasy, oily handles are slippery causing
loss of control.
Obey the instructions for lubricating and changing
accessories.
Disconnect the spark plug cable before you
assemble the product, put the product into storage or
do maintenance.
If you cannot adjust the idle speed to make the
cutting attachment stop, speak to your service
center. Do not use the product until the product is
correctly adjusted or repaired.
Make sure the product is stable during transport to
prevent damage.
When not in operation, keep the product in a dry,
high or locked area away from children.
ASSEMBLY
WARNING: Read the safety chapter before
you assemble the product.
To assemble the handle
1. Remove the screws (A), washers (B), top clamp (D),
bottom clamp (E) and nuts (F) from the handle (C).
(Fig. 35)
2. Attach the top clamp (A), handle (B), washers (C)
and screws (D) to the top of the upper shaft.
3. Attach the bottom clamp (E) and nuts (F) to the
bottom of the upper shaft. (Fig. 36)
4. Put the assist handle between the 2 arrows on the
upper shaft.
5. Fully tighten the screws.
Note: Make sure the handle does not move.
16 860 - 001 - 28.10.2018
To assemble the trimmer attachment
1. Attach the cutting attachment guard (A), braces (B),
washers (C), washers (D), and screws (E). Fully
tighten the screws. (Fig. 37)
2. Insert the hex wrench (A) to prevent rotation of the
shaft.
3. Remove the nut (B), support cup (C) and holder (D)
on the trimmer and brushcutter attachment. (Fig. 38)
4. Tighten the trimmer head (B) onto the shaft. (Fig. 39)
To assemble the brushcutter
attachment
1. Attach the cutting attachment guard (A), braces (B),
washers (C), washers (D), and screws (E). Fully
tighten the screws. (Fig. 37)
2. Insert the hex wrench (A) to prevent rotation of the
shaft.
3. Remove the nut (B), support cup (C) and holder (D)
on the trimmer and brushcutter attachment. (Fig. 40)
4. Attach the blade (B), bottom holder (C), support cup
(D), and nut (E). Fully tighten the nut. (Fig. 41)
To assemble the pole saw
attachment
See
To do the maintenance on the pole saw attachment
on page 20
for assembly instructions for the pole saw
attachment.
To assemble the two-piece shaft
1. Turn the knob to loosen the shaft coupling. (Fig. 42)
2. Move the locking/release button (A) into the guide
recess. Push the attachment into the coupler until
the locking/release button sets into the primary hole
(B). (Fig. 43)
3. Insert the shaft into the shaft coupling. The button
must go through the hole.
Note: If the attachment does not go fully into the
upper shaft, use the combination tool to push the
internal drive shaft deeper into the tube. It can be
necessary to turn the combination tool while you
push.
4. Make sure that you fully tighten the knob before you
operate the product. (Fig. 44)
To disassemble the two-piece shaft
1. Turn the knob to loosen the shaft coupling. (Fig. 45)
2. Push and hold the locking/release button (B). Pull
the shafts apart. (Fig. 46)
OPERATION
WARNING: Read and understand the safety
chapter before you operate the product.
Fuel
To use fuel
CAUTION: This product has a two-cycle
engine. Use a mixture of gasoline and two-
cycle engine oil. Make sure to use the
correct quantity of oil in the mixture.
Incorrect ratio of gasoline and oil can cause
damage to the engine.
Gasoline
CAUTION: Do not use gasoline with an
octane number less than 90 RON (87 AKI).
This can cause damage to the product.
CAUTION: Do not use gasoline with more
than 10% ethanol concentration (E10). This
can cause damage to the product.
Always use new unleaded gasoline with a minimum
octane number of 90 RON (87 AKI) and with less
than 10% ethanol concentration (E10).
Use gasoline with a higher octane number if you
frequently use the product at continuously high
engine speed.
Two-cycle engine oil
Use only high quality two-cycle engine oil. Use only
an air cooled engine oil.
Do not use other types of oil.
Mixture ratio 50:1 (2%)
Petrol, litre Two-stroke oil, litre
5 0.10
10 0.20
15 0.30
20 0.40
860 - 001 - 28.10.2018 17
To make the fuel mixture
Note: Always use a clean fuel container when you mix
the fuel.
Note: Do not make more than 30 days quantity of fuel
mixture.
1. Add half of the gasoline quantity.
2. Add the full quantity of oil.
3. Shake the fuel mixture to mix the contents.
4. Add the remaining gasoline quantity.
5. Shake the fuel mixture to mix the contents.
6. Fill the fuel tank.
To add fuel
Always use a fuel container with an antispill valve.
If there is some fuel on the container, remove the
unwanted fuel and let the container dry.
Make sure that the area near the fuel tank cap is
clean.
Shake the fuel container before you add the fuel
mixture to the fuel tank.
To start and stop
To start a cold engine
(Fig. 47)
1. Set the stop switch (A) to the start position.
2. Push the throttle lockout (B) and then pull the throttle
trigger (C).
3. While the throttle trigger is engaged, push the fast
idle button (D).
4. Release the throttle lockout and the throttle trigger.
5. Push the air purge bulb 10 times. The bulb does not
need to be completely filled. (Fig. 48)
6. Move the choke control to the full choke position.
(Fig. 49)
7. Hold the body of the machine on the ground with the
left hand. (Fig. 50)
8. Pull out the cord slowly with your right hand until you
feel some resistance.
9. Pull the starter cord quickly and powerfully. Repeat
approximately 5 times or until the engine attempts to
start.
10. Move the choke control to the no choke position.
11. Pull the starter cord quickly and powerfully until the
engine starts.
12. Let the engine run for 10 seconds.
13. Pull the throttle trigger to run at low speed for 60
seconds.
To start a warm engine
Note: Obey this procedure when you start a product that
has run out of fuel and has been refueled.
(Fig. 47)
1. Set the stop switch (A) to the start position.
2. Push the throttle lockout (B) and then pull the throttle
trigger (C).
3. While the throttle trigger is engaged, push the fast
idle button (D).
4. Release the throttle lockout and the throttle trigger.
5. Push the air purge bulb 10 times. The bulb does not
need to be completely filled. (Fig. 48)
6. Hold the body of the machine on the ground with the
left hand. (Fig. 50)
7. Move the choke control to the no choke position.
8. Pull out the cord slowly with your right hand until you
feel some resistance.
9. Pull the starter cord quickly and powerfully until the
engine starts.
To stop the product
Push the stop switch to stop the engine.
To start the engine when the fuel is too hot
If the product does not start, the fuel can be too hot.
Note:
Always use new fuel and decrease the operation
time during warm weather.
1. Put the product in a cool area away from open
sunlight.
2. Let the product cool down for 20 minutes at
minimum.
3. Press the primer bulb again and again for 10-15
seconds.
4. Obey the procedure to start a cold engine. Refer to
To start a cold engine on page 18
.
MAINTENANCE
WARNING: Read and understand the safety
chapter before you clean, repair or do
maintenance on the product.
Maintenance schedule
Make sure that you obey the maintenance schedule.
The intervals are calculated from daily use of the
product. The intervals are different if you do not use the
product each day. Only do the maintenance work that is
18 860 - 001 - 28.10.2018
found in this manual. Speak to an approved service
center about other maintenance work not found in this
manual.
Daily maintenance
Clean the external surfaces.
Clean the air filter. Replace if necessary.
Check the harness.
Check the throttle trigger lock and the throttle
function.
Check the handle and the handle bar.
Check the stop switch.
Check the guards.
Check the cutting attachment for damage or cracks.
Replace a damaged cutting attachment.
Lubricate the cutting blades (extended hedge
trimmer attachment).
Check the trimmer head.
Examine the idle speed.
Examine for fuel leaks.
Weekly maintenance
Examine the starter rope handle and the starter
rope.
Examine the bevel gear grease.
Clean the outside of the carburettor and its adjacent
areas.
Clean the outside of the spark plug. Remove it and
check the electrode gap. Adjust the gap or replace
the spark plug. Check that the spark plug is fitted
with a suppressor.
Monthly maintenance
Clean the cooling system.
Examine the fuel filter.
Examine the fuel hose for damage.
Examine all cables and connections.
Examine the fuel filter.
To adjust the carburetor
The basic carburetor settings are adjusted during testing
at the factory. Adjustment must be carried out by a
trained technician.
To do a check of the muffler
WARNING:
Do not use a product that has a
defective muffler. Always replace a defective
muffler.
WARNING: Mufflers with catalytic
converters get very hot during operation.
Risk of burn or fire.
WARNING: The muffler decrease the noise
level and point the exhaust gases from the
operator. The exhaust gases are hot and
can contain sparks. Risk of fire.
CAUTION: The spark arrestor spark arrester
screen must be replaced if it is damaged. Do
not use a product if the spark arrestor spark
arrester screen on the muffler is missing or
defective.
CAUTION: If the spark arrestor spark
arrester screen is blocked the product will
too hot. This will cause damage to the
cylinder and piston.
1. Make sure that the muffler is not damaged.
2. Make sure that the muffler is correctly attached to
the product.
3. Some mufflers have a special spark arrestor spark
arrester screen. Clean the spark arrestor spark
arrester screen minimum one a week if your product
has this type of muffler. Use a wire brush. (Fig. 51)
To clean/do maintenance on the
cooling system
This product has a cooling system. A dirty or blocked
cooling system can make the product too hot which can
damage to the piston and cylinder. Check and clean the
cooling system with a brush one time each week or
more frequently in demanding conditions. The cooling
system consists of cooling fins on the cylinder (1) and air
intake (2).
(Fig. 52)
To clean the air filter
1. Remove the air filter cover and remove the air filter.
(Fig. 53)
2. Clean the air filter with warm soap water. Make sure
that the air filter is dry before you install it.
3. Replace the air filter if it is too dirty to fully clean it.
Always replace a damaged air filter.
4. If your product has a foam air filter, apply air filter oil.
Only apply air filter oil to a foam filter. Do not apply
oil to a felt filter.
Fuel filter
When the engine runs short of fuel, make sure that the
air hole in the fuel tank cap and the fuel filter (A) are
clean.
(Fig. 54)
To add grease to the bevel gear
Make sure that the bevel gear is filled 3/4 full with bevel
gear grease.
(Fig. 55)
860 - 001 - 28.10.2018
19
To examine the spark plug
CAUTION: Always use the recommended
spark plug type. Incorrect spark plug type
can cause damage to the product.
Examine the spark plug if the engine is low on
power, is not easy to start or does not operate
correctly at idle speed.
To decrease the risk of unwanted material on the
spark plug electrodes, obey these instructions:
a) Make sure that the idle speed is correctly
adjusted.
b) Make sure that the fuel mixture is correct.
c) Make sure that the air filter is clean.
If the spark plug is dirty, clean it and make sure that
the electrode gap is correct, refer to
TECHNICAL
DATA on page 22
. (Fig. 56)
Replace the spark plug if it is necessary.
To sharpen grass cutters and grass
blades
1. Sharpen grass cutters and grass blades with a
single-cut flat file.
2. Sharpen all edges of the grass cutters and blades
equally to keep the balance. (Fig. 57)
To replace the trimmer line
(Fig. 58)
(Fig. 59)
(Fig. 60)
(Fig. 61)
(Fig. 62)
(Fig. 63)
(Fig. 64)
(Fig. 65)
To do the maintenance on the pole
saw attachment
WARNING: Remove the spark plug before
you do the maintenance on the attachment.
To install or replace the chain
WARNING:
When the chain becomes worn
or damaged, replace it with the low kickback
chain. See
ATTACHMENTS on page 23
.
Note: Always use gloves when you touch the chain.
1. Disconnect the spark plug cap.
2. Use the wrench to loosen the sprocket cover nut by
turning counterclockwise. (Fig. 66)
3. Remove the sprocket cover nut, washer (B) and
sprocket cover (C). (Fig. 67)
4. Remove the guide bar and saw chain if they are
installed.
5. If you are replacing a chain, remove the old chain
from the guide bar and discard it.
6. Remove all sawdust, dirt and other unwanted
material from the surfaces with a soft brush or a dry
cloth.
7. Do the maintenance on the guide bar. See
To do the
maintenance on the guide bar on page 21
.
8. Turn the adjustment screw counterclockwise until the
adjustment pin is at the position shown. (Fig. 68)
9. Install the new chain on the guide bar with the
cutters in the correct direction. Start at the top of the
guide bar and move to the front of the guide bar.
(Fig. 69)
Note: Make sure the bottom of the chain is in the
groove on the guide bar and engaged on the front
sprocket of the guide bar.
10. When the chain is on the guide bar, install them on
the saw and put the chain around the sprocket. Align
the sprocket teeth with the chain.
11. Make sure the adjustment pin is in the adjustment
pin hole of the guide bar. (Fig. 70)
Note: An adjustment pin and screw are used to
adjust the tension of the chain. It is very important
when you assemble the guide bar that the
adjustment pin is engaged in the adjustment pin hole
on the guide bar.
12. Attach the sprocket cover (A), washer (B) and
sprocket cover nut (C). Lightly tighten the nut with
your fingers. (Fig. 71)
13. Adjust the chain tension. See
To adjust the chain
tension on page 20
.
Note:
Examine the chain tension regularly. A chain
that has the correct tension has better performance
and longer life.
To adjust the chain tension
WARNING:
Put on the gloves before you
adjust the chain tension. The chain is sharp
and can cause injuries to you.
Note: The chain extends during the operation, specially
when you operate for the first 15 minutes. You must
examine and adjust the chain tension frequently after
you use or refuel the product.
1. Examine the chain and guide bar for any damage.
Replace any part that is damaged.
20
860 - 001 - 28.10.2018
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268
  • Page 269 269
  • Page 270 270
  • Page 271 271
  • Page 272 272
  • Page 273 273
  • Page 274 274
  • Page 275 275
  • Page 276 276
  • Page 277 277
  • Page 278 278
  • Page 279 279
  • Page 280 280
  • Page 281 281
  • Page 282 282
  • Page 283 283
  • Page 284 284
  • Page 285 285
  • Page 286 286
  • Page 287 287
  • Page 288 288
  • Page 289 289
  • Page 290 290
  • Page 291 291
  • Page 292 292
  • Page 293 293
  • Page 294 294
  • Page 295 295
  • Page 296 296
  • Page 297 297
  • Page 298 298
  • Page 299 299
  • Page 300 300
  • Page 301 301
  • Page 302 302
  • Page 303 303
  • Page 304 304
  • Page 305 305
  • Page 306 306
  • Page 307 307
  • Page 308 308
  • Page 309 309
  • Page 310 310
  • Page 311 311
  • Page 312 312
  • Page 313 313
  • Page 314 314
  • Page 315 315
  • Page 316 316
  • Page 317 317
  • Page 318 318
  • Page 319 319
  • Page 320 320
  • Page 321 321
  • Page 322 322
  • Page 323 323
  • Page 324 324
  • Page 325 325
  • Page 326 326
  • Page 327 327
  • Page 328 328
  • Page 329 329
  • Page 330 330
  • Page 331 331
  • Page 332 332
  • Page 333 333
  • Page 334 334
  • Page 335 335
  • Page 336 336
  • Page 337 337
  • Page 338 338
  • Page 339 339
  • Page 340 340
  • Page 341 341
  • Page 342 342
  • Page 343 343
  • Page 344 344
  • Page 345 345
  • Page 346 346
  • Page 347 347
  • Page 348 348
  • Page 349 349
  • Page 350 350
  • Page 351 351
  • Page 352 352
  • Page 353 353
  • Page 354 354
  • Page 355 355
  • Page 356 356
  • Page 357 357
  • Page 358 358
  • Page 359 359
  • Page 360 360
  • Page 361 361
  • Page 362 362
  • Page 363 363
  • Page 364 364
  • Page 365 365
  • Page 366 366
  • Page 367 367
  • Page 368 368
  • Page 369 369
  • Page 370 370
  • Page 371 371
  • Page 372 372
  • Page 373 373
  • Page 374 374
  • Page 375 375
  • Page 376 376
  • Page 377 377
  • Page 378 378
  • Page 379 379
  • Page 380 380
  • Page 381 381
  • Page 382 382
  • Page 383 383
  • Page 384 384
  • Page 385 385
  • Page 386 386
  • Page 387 387
  • Page 388 388
  • Page 389 389
  • Page 390 390
  • Page 391 391
  • Page 392 392
  • Page 393 393
  • Page 394 394
  • Page 395 395
  • Page 396 396
  • Page 397 397
  • Page 398 398
  • Page 399 399
  • Page 400 400
  • Page 401 401
  • Page 402 402
  • Page 403 403
  • Page 404 404
  • Page 405 405
  • Page 406 406
  • Page 407 407
  • Page 408 408
  • Page 409 409
  • Page 410 410
  • Page 411 411
  • Page 412 412
  • Page 413 413
  • Page 414 414
  • Page 415 415
  • Page 416 416
  • Page 417 417
  • Page 418 418
  • Page 419 419
  • Page 420 420
  • Page 421 421
  • Page 422 422
  • Page 423 423
  • Page 424 424
  • Page 425 425
  • Page 426 426
  • Page 427 427
  • Page 428 428
  • Page 429 429
  • Page 430 430
  • Page 431 431
  • Page 432 432
  • Page 433 433
  • Page 434 434
  • Page 435 435
  • Page 436 436
  • Page 437 437
  • Page 438 438
  • Page 439 439
  • Page 440 440
  • Page 441 441
  • Page 442 442
  • Page 443 443
  • Page 444 444
  • Page 445 445
  • Page 446 446
  • Page 447 447
  • Page 448 448
  • Page 449 449
  • Page 450 450
  • Page 451 451
  • Page 452 452
  • Page 453 453
  • Page 454 454
  • Page 455 455
  • Page 456 456
  • Page 457 457
  • Page 458 458
  • Page 459 459
  • Page 460 460
  • Page 461 461
  • Page 462 462
  • Page 463 463
  • Page 464 464
  • Page 465 465
  • Page 466 466
  • Page 467 467
  • Page 468 468
  • Page 469 469
  • Page 470 470
  • Page 471 471
  • Page 472 472
  • Page 473 473
  • Page 474 474
  • Page 475 475
  • Page 476 476
  • Page 477 477
  • Page 478 478
  • Page 479 479
  • Page 480 480
  • Page 481 481
  • Page 482 482
  • Page 483 483
  • Page 484 484
  • Page 485 485
  • Page 486 486
  • Page 487 487
  • Page 488 488
  • Page 489 489
  • Page 490 490
  • Page 491 491
  • Page 492 492
  • Page 493 493
  • Page 494 494
  • Page 495 495
  • Page 496 496
  • Page 497 497
  • Page 498 498
  • Page 499 499
  • Page 500 500
  • Page 501 501
  • Page 502 502
  • Page 503 503
  • Page 504 504

McCulloch B33 PS4in1 Kit Manualul proprietarului

Tip
Manualul proprietarului
Acest manual este potrivit și pentru