Yamaha CDRHD1300 Manualul proprietarului

Categorie
CD playere
Tip
Manualul proprietarului

Acest manual este potrivit și pentru

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Printed in Malaysia V956620
UAB
OWNER’S MANUAL
MODE D’EMPLOI
CDR-HD1300
CDR-HD1300E
HDD/CD Recorder
Enregistreur CD/Disque Dur
CDR-HD1300
TEXT/TIME MODE
MULTI JOG
DIGITAL REC LEVEL
PUSH ENTER
TRACK NO.
FINALIZE ERASE
BOOKMARK
COMPLETE
MENU
CLEAR
MIN MAX
OPTICAL
ANALOG REC LEVEL
INPUT
REC
COAXIAL
ANALOG
CLASS 1 LASER PRODUCT
LASER KLASSE 1 PRODUKT
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPART
PRODUIT LASER DE CLASSE 1
LINE IN — LINE OUT IN OUT
DIGITAL
REC COAXIAL OPTICAL COAXIAL OPTICAL
RS–232C
VIDEO
VIDEO
OUT
S VIDEO
ANALOG
PLAY
R
L
R
L
4 3
CLASS 1 LASER PRODUCT
LASER KLASSE 1 PRODUKT
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPART
PRODUIT LASER DE CLASSE 1
LINE IN — LINE OUT IN OUT
DIGITAL
REC COAXIAL OPTICAL COAXIAL OPTICAL
RS–232C
VIDEO
VIDEO
OUT
S VIDEO
ANALOG
PLAY
R
L
R
L
4 3
VARO!
AVATTAESSA JA SUOJALUKITUS OHITETTAESSA
OLET ALTTIINA NÄKYMÄTTÖMÄLLE
LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
VARNING!
OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR
ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.
BETRAKTA EJ STRÅLEN.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
ATTENTION
L’emploi de commandes, de réglages ou un choix de
procédures différents des spécifications de cette
brochure peut entraîner une exposition à d’éventuelles
radiations pouvant être dangereses.
ACHTUNG
Die Verwendung von Bedienungselementen oder
Einstellungen oder die Durchführung von
Bedienungsvorgängen, die nicht in dieser Anleitung
aufgeführt sind, kann zu einem Kontakt mit
gefährlichen Laserstrahlen führen.
OBSERVERA
Användning av kontroller och justeringar eller
genomförande av procedurer andra än de som
specificeras i denna bok kan resultera i att du utsätter
dig för farlig strålning.
ATTENZIONE
Uso di controlli o regolazioni o procedure non
specificamente descritte può causare l’esposizione a
radiazioni di livello pericoloso.
PRECAUCIÓN
El uso de los controles o los procedimientos de ajuste
o utilización diferentes de los especificados en este
manual pueden causar una exposición peligrosa a la
radiación.
VOORZICHTIG
Gebruik van bedieningsorganen of instellingen, of
uitvoeren van handelingen anders dan staan
beschreven in deze handleiding kunnen leiden tot
blootstelling aan gevaarlijke stralen.
(For U.S.A. model)
(For U.K. and Europe models)
CLASS 1 LASER PRODUCT
LASER KLASSE 1 PRODUKT
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPART
PRODUIT LASER DE CLASSE 1
CLASS 1 LASER PRODUCT
LASER KLASSE 1 PRODUKT
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPART
PRODUIT LASER DE CLASSE 1
CAUTION - VISIBLE AND
/
OR INVISIBLE LASER RADIATION WHEN OPEN.
AVOID EXPOSURE TO BEAM.
VARNING - SYNLIG OCH
/
ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA
DEL ÄR ÖPPNAD. STRÅLEN ÄR FARLIG.
VARNING - SYNLIG OCH
/
ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA DEL
ÄR ÖPPNAD. BETRAKTA EJ STRÅLEN.
VARO !
AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA
/
TAI
NÄKYMÄTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
VORSICHT !
SICHTBARE UND
/
ODER UNSICHTBARE LASERSTRAHLUNG
WENN ABDECKUNG GEÖFFNET. NICHT DEM STRAHL AUSSETZEN.
ATTENTION -
RADIATION VISIBLE ET / OU INVISIBLE LORSQUE L'ALLAREIL
EST OUVERT. EVITEZ TOUTE EXPOSITION AU FAISCEAU.
000_HD1300(CA)H14_(7.5mm) 02.6.26, 10:01 AM2
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert you to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert you to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8 Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers)
that produce heat.
9 Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10 Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
13 Unplug this apparatus during lightning
storms or when unused for long periods of time.
14 Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
IMPORTANT!
Please record the serial number of this unit in the space below.
Model:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future reference.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
IMPORTANT SAFETY INSTRUCTIONS
100_HD1300(E)Caut 02.6.24, 6:51 PM2
FCC INFORMATION (for US customers)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions
contained in this manual, meets FCC requirements.
Modifications not expressly approved by Yamaha may void
your authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product MUST
be used. Follow all installation instructions. Failure to
follow instructions could void your FCC authorization to
use this product in the USA.
3. NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15 for
Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurance that
your use of this product in a residential environment will
not result in harmful interference with other electronic
devices.
This equipment generates/uses radio frequencies and, if not
installed and used according to the instructions found in the
users manual, may cause interference harmful to the
operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product is
found to be the source of interference, which can be determined
by turning the unit “OFF” and “ON”, please try to eliminate the
problem by using one of the following measures:
Relocate either this product or the device that is being affected
by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead, change
the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory results,
please contact the local retailer authorized to distribute this
type of product. If you can not locate the appropriate retailer,
please contact Yamaha Electronics Corp., U.S.A. 6660
Orangethorpe Ave, Buena Park, CA 90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your
equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or
distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is often
undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer Electronics Group recommend
you to avoid prolonged exposure from excessive volume levels.
100_HD1300(E)Caut 02.6.24, 6:51 PM3
CAUTION: READ THIS BEFORE OPERATING THIS UNIT
To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
Install this unit in a well ventilated, cool, dry, clean place – away
from direct sunlight, heat sources, vibration, dust, moisture, and/
or cold. Avoid ventilation space of at least 30 cm on the top, 20
cm on the left and right, and 10 cm on the back of this unit.
Locate this unit away from other electrical appliances, motors, or
transformers to avoid humming sounds.
Do not expose this unit to sudden temperature changes from cold
to hot, and do not locate this unit in a environment with high
humidity (i.e. a room with a humidifier) to prevent condensation
inside this unit, which may cause an electrical shock, fire, damage
to this unit, and/or personal injury.
Avoid installing this unit where foreign object may fall onto this
unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do NOT place:
Other components, as they may cause damage and/or
discoloration on the surface of this unit.
Burning objects (i.e. candles), as they may cause fire, damage
to this unit, and/or personal injury.
Containers with liquid in them, as they may fall and liquid
may electrical shock to the user and/or damage to this unit.
Do not cover the rear panel of this unit with a newspaper,
tablecloth, curtain, etc. in order not to obstruct heat radiation. If
the temperature inside this unit rises, it may cause fire, damage to
this unit, and/or personal injury.
Do not plug in this unit to a wall outlet until all connections are
complete.
Do not operate this unit upside-down. It may overheat, possibly
causing damage.
Do not use force on switches, knobs and/or cords.
When disconnecting the power cord from the wall outlet, grasp
the plug; do not pull the cord.
Do not clean this unit with chemical solvents; this might damage
the finish. Use a clean, dry cloth.
Only voltage specified on this unit must be used. Using this unit
with a higher voltage than specified is dangerous and may cause
fire, damage to this unit, and/or personal injury. YAMAHA will
not be held responsible for any damage resulting from use of this
unit with a voltage other than specified.
To prevent damage by lightning, disconnect the power cord from
the wall outlet during an electrical storm.
Do not attempt to modify or fix this unit. Contact qualified
YAMAHA service personnel when any service is needed. The
cabinet should never be opened for any reasons.
When not planning to use this unit for long periods of time (i.e.
vacation), disconnect the AC power plug from the wall outlet.
Be sure to read the “TROUBLESHOOTING” section on common
operating errors before concluding that this unit is faulty.
Before moving this unit, first check that there is no disc in the disc
tray. Finally, press POWER to turn off this unit, and disconnect
the AC power plug from the wall outlet.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
SPECIAL INSTRUCTIONS FOR U.K. MODEL
IMPORTANT
The wires in this mains lead are coloures in accordance with the
following code:
GREEN-and-YELLOW:Earth
BLUE:Neutral
BROWN:Live
As the colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings identifying the
terminals in your plug proceed as follows: The wire which is
coloured GREEN-and-YELLOW must be connected to the
terminal in the plug which is marked by the letter E or by the
safety earth symbol or coloured GREEN or GREEN-and -
YELLOW. The wire which is coloured BLUE must be
connected to the terminal which is marked with the letter N or
coloured BLACK. The wire which is coloured BROWN must be
connected to the terminal which is marked with the letter L or
coloured RED.
For U.K. customers
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an appropriate
3 pin plug fitted. For details, refer to the instructions described
above.
Note: The plug severed from the mains lead must be destroyed, as
a plug with bared flexible cord is hazardous if engaged in a live
socket outlet.
For Canadian Customers
To prevent electric shock, match wide blade of plug to wide slot
and fully insert.
This Class B digital apparatus complies with Canadian ICES–
003.
i
100_HD1300(E)Caut 02.6.26, 6:05 PM4
English
ii
Hard Disk Drive (HDD)
Before using
If you purchase CDR-HD1300; this model is not equipped with a hard disk drive (HDD). Please purchase a commercially available HDD
for internal use and install it on this unit correctly, following the attached instruction.
It is necessary to format a new HDD after installation. Also refer the attached instruction for formatting.
If you purchase CDR-HD1300E; this model is equipped with an HDD.
Capacity of the HDD
Following table shows the total recordable time for different capacities of an HDD.
Handling of the HDD
The HDD formatted on your CDR-HD1300 cannot be used on other CDR-HD1300s for any reading or writing. If you wish to use the HDD
that has been formatted on other CDR-HD1300 on yours, format it again on your CDR-HD1300. See page 85 for formatting.
Carefully handle an HDD before installation because it is a precision device. Also do not give vibration or shock to this unit after the HDD
is installed. Incorrect operation can damage the HDD and/or the data written onto the HDD.
Yamaha and suppliers accept no liability for the loss and/or damage of data caused by vibration and/or shock.
CD player mode
This unit does not make any recordings if no HDD is installed. In this case, only reading of a CD, CD-R, and CD-RW disc is possible. Permit
some time until this unit becomes ready after the power is turned if no HDD is installed.
Total recordable time
Approx. 30 hours
Approx. 60 hours
Approx. 90 hours
Approx. 120 hours
Capacity
20 GB
40 GB
60 GB
80 GB
101_HD1300(E)Caut02 02.6.26, 6:06 PM3
iii
About this manual
This manual is printed prior to production. Design and specifica-
tions are subject to change in part for the reason of the improve-
ment in operativity ability, and others. In this case, the product has
priority.
Some of the illustrations and names of the package contents etc
written in this manual may differ from the actual products and the
names written on the package etc.
Features
Copying a CD to the HDD at maximum 10x speed
Copying data on the HDD to a CD-R disc at maximum 8x speed
Copying data on the HDD to a CD-RW disc at maximum 4x speed
High quality recording by the Audio Master Quality Recording (copying from the HDD to a CD-R only)
Long-hour-recording useful for recording satellite broadcasting programs and timer recording using an external timer
About This Manual
Structure
This owner’s manual is composed of following sections.
GETTING STARTED
This section explains necessary preparations such as remote control
and connection. Please read this before using this unit.
COPYING AND RECORDING ONTO THE HDD
This section describes basic operations; copying from a CD to the
HDD and recording from an external component connected to this
unit to the HDD. Additional functions and operations are explained
in “Advanced Operations” following this basic operation. Skip this
part, if you wish to try to use all the basic functions equipped on
this unit.
EDITING
This section describes how to edit the data copied and/or written on
the HDD. Editing method is explained for “album”, “track”, and
“disc” respectively. See “EDITING MENU ITEMS” for outline of
the editing menu.
COPYING AND RECORDING ONTO A CD-R OR CD-RW
DISC
This section describes basic operations; copying from the HDD to a
CD-R or CD-RW and recording from an external component
connected to this unit to a CD-R or CD-RW. Additional functions
and operations are explained in “Advanced Operations” following
these basic operations. Skip this part, if you wish to try to use all
the basic functions equipped on this unit.
DUPLICATION OF A CD
This section describes how to duplicate a whole CD.
PLAYBACK
This section describes how to play the data copied/written on the
HDD, your original CDs that are made using this unit, or commer-
cially available CDs.
APPENDIX
This section provides you with the information about system setting
of this unit and troubleshooting.
101_HD1300(E)Caut02 02.6.26, 6:07 PM4
E-1
English
Contents
GETTING STARTED
SUPPLIED ACCESSORIES ............................................ 2
CD/CD-R/CD-RW COMPATIBLE WITH THIS UNIT ........ 3
RULES OF DIGITAL RECORDING AND NOTES ON
SYSTEM ...................................................................... 5
Rules of Digital Recording .................................................... 5
Notes on System .................................................................... 5
Data on the HDD ................................................................... 6
NAMES OF BUTTONS AND CONTROLS ...................... 7
Front Panel ............................................................................. 7
Remote Control ..................................................................... 8
Display ................................................................................. 10
Display Information ............................................................. 11
Rear Panel ............................................................................ 12
CONNECTIONS ............................................................ 12
COPYING AND RECORDING ONTO THE HDD
COPYING FROM A CD ONTO THE HDD ..................... 14
Copying All Tracks on a CD ............................................... 14
Copying Favorite Tracks on the CD .................................... 16
Advanced Operations .......................................................... 17
RECORDING FROM AN EXTERNAL COMPONENT
ONTO THE HDD ........................................................ 20
Recording from the Digital Components ............................ 20
Recording from the Analog Components ............................ 21
Recording Using an External Timer .................................... 22
Adjusting the Recording Level ............................................ 24
Advanced Operations .......................................................... 25
EDITING
EDITING MENU ITEMS ................................................. 29
ALBUM EDITING .......................................................... 30
Album Editing Operation .................................................... 30
TRACK EDITING ........................................................... 39
Track Editing Operation ...................................................... 39
DISC EDITING ............................................................... 52
Disc Editing Operation ........................................................ 52
UNDO FUNCTION ......................................................... 58
BOOKMARK ................................................................. 59
COPYING AND RECORDING ONTO A CD-R OR
CD-RW DISC
COPYING FROM THE HDD ONTO A CD-R OR CD-RW
DISC ........................................................................... 60
Copying a Whole Group (Disc, Album or Bookmark) ........ 60
Copying Favorite Tracks on the HDD ................................. 62
High Quality Copying ......................................................... 63
Advanced Operations .......................................................... 64
RECORDING FROM AN EXTERNAL COMPONENT
ONTO A CD-R OR CD-RW DISC .............................. 67
Advanced Operations .......................................................... 69
FINALIZATION .............................................................. 70
ERASING A CD-RW DISC ............................................ 71
DUPLICATION OF A CD
DUPLICATION OF A CD ............................................... 72
High Quality Duplication .................................................... 74
PLAYBACK
PLAYBACK .................................................................... 76
Playing a CD ........................................................................ 76
Playing Tracks on the HDD ................................................. 76
Finding the Desired Passage (Search) ................................. 77
Finding the Desired Group (Group Skip) ............................ 77
Finding the Desired Track (Track Skip) .............................. 78
Selecting Tracks Using On-Screen-Display (OSD) ............ 79
Listening with Headphones ................................................. 79
VARIOUS PLAYBACK .................................................. 80
Finding the Desired Passage by Time (Time Search) .......... 80
Setting the Play Style ........................................................... 80
Single Repeat Play ............................................................... 81
Full Repeat Play .................................................................. 82
Random Play ....................................................................... 82
Intro Play ............................................................................. 83
Bookmark Play .................................................................... 83
APPENDIX
DAC (DIGITAL/ANALOG CONVERTER) MODE .......... 84
HDD UTILITY ................................................................. 85
SYSTEM UTILITY .......................................................... 86
ON-SCREEN DISPLAY (OSD) ...................................... 89
DISPLAY MESSAGES ................................................... 90
TROUBLESHOOTING ................................................... 92
ABOUT PRODUCT INFORMATIONS ........................... 93
SPECIFICATIONS ......................................................... 94
102_HD1300(E)01-13 02.6.24, 6:51 PM1
E-2
SUPPLIED ACCESSORIES
Make sure the following items are included in your package.
Remote Control Batteries (size AA, UM-3, or R6) (2)
OPEN/CLOSE
COPY REC
TEXT/TIME
TRACK NO.
WRITE
MODE MENU
CLEAR
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQR
7
STU
8
VWX
9
YZ
SPACE
SYMBOL
0
+
10
BOOKMARK
REPEAT RANDOM
GROUP SKIP
INTRO
ENTER
COMPLETE
A.M.Q.R.
FINALIZE
INPUT
TIMER REC
ERASE
HDD CDR
Audio Pin Cables (2)
Optical Cable
Video Pin Cable
Power Cable (for U.S.A. model)
Coaxial Cable (for U.S.A. model)
102_HD1300(E)01-13 02.6.24, 6:51 PM2
E-3
English
GETTING STARTED
CD/CD-R/CD-RW COMPATIBLE WITH THIS UNIT
Discs that can be used for recording on
this unit
Be sure to use only CD-R and CD-RW discs made by reliable
manufacturers.
CD-R and CD-RW digital audio discs that display either of the
following marks can be used with this unit.
Discs that can be used for recording
CD-R discs can only be recorded on once, and the recorded
material cannot be erased.
CD-RW discs can be recorded on, have the recorded material
erased, and then recorded on again any number of times.
Discs that cannot be used for recording on
this unit
Discs bearing marks other than those shown above.
Discs intended for recording computer data.
Discs intended for professional use or labeled FOR PROFES-
SIONAL USE ONLY.
79-minute CD-R disc
The actual recordable time of the CD-R disc with 80 written on
its package is 79 minutes 57 seconds. This manual describes such
CD-R disc as 79-minute CD-R disc.
Finalization of CD-R/CD-RW discs
To play back CD-R discs on a standard CD player and CD-RW
discs on CD-RW-compatible players, you need to perform the
process known as finalization. In the finalization process, the
Table of Contents (TOC) is written onto the discs.
Finalized CD-R discs
CD-R discs can be played on a standard CD player.
Further recording onto CD-R discs is not possible.
Some CD players may not play back the finalized CD-R discs
properly due to differences in the playback system of different
manufacturers.
Finalized CD-RW discs
CD-RW discs cannot be played on a standard CD player. CD-RW
discs can be played back on CD-RW-compatible players such as
this unit.
Tracks written on CD-RW discs can be erased, and additional
tracks can be recorded after the TOC has been erased.
Erasure or loss of data
Yamaha and suppliers accept no liability for the loss of data written
on the HDD and CD-R or CD-RW discs, or any problems caused as
a result of using this unit. As a precaution, it is recommended that
the discs are tested after they have been recorded on. Furthermore,
under no circumstances do Yamaha and suppliers guarantee the
reliability of the discs.
Discs that can be played back
In addition to CD-R and CD-RW digital audio discs described
above, commercially available pre-recorded CDs bearing the marks
shown below can also be played on this unit.
Caution
If you use the CDs that do not meet the CD standards, this unit
may not operate properly.
Playback of the CD-R disc copied with the
Audio Master Quality Recording mode
The Audio Master Quality Recording mode enables you to create a
CD with high quality sounds by increasing the linear velocity when
copying. The CD-R discs copied with this mode meet the CD
standards and can be played on a standard CD player. However,
some CD recorders may not play back these CD-R discs properly.
Playback on DVD players
Before playing back a finalized CD-R or CD-RW discs on a DVD
player, please check whether the DVD player is compatible with
CD-R or CD-RW discs or not. Refer to the owners manual of the
DVD player for more information. CD-R or CD-RW discs cannot
be played on a DVD player that is not compatible with CD-R or
CD-RW discs.
IMPORTANT
Please check the copyright laws in your country to record from
records, CDs, radio, etc. Recording of copyright material may
infringe copyright laws.
FOR CONSUMER
FOR CONSUMER USE
FOR MUSIC USE ONLY
102_HD1300(E)01-13 02.6.24, 6:51 PM3
E-4
Handling of discs
Heed the following notes on handling of discs not to create any
cause for a recording failure, a loss of the recorded data, or a
malfunction of this unit.
This compact disc recorder is designed for use with CDs
(including 8cm [3] discs) bearing the , , , or
marks only. Never attempt to load any other type of disc into this
unit.
CDs are not subjected to wear during play. However if the disc is
handled improperly, damage may be created on the disc to
adversely affect the discs play.
When writing on the label side of CD-R or CD-RW discs, use an
oil-based felt-tipped pen.
Do not use cleaning discs or warped discs. All of these could
damage this unit.
Although playback of CDs is generally not affected by small
particles of dust or fingerprints on their playing surface, dust,
fingerprints, small scratches and direct sunlight on the recording
surface of a CD-R or CD-RW disc may make recording impos-
sible. Therefore, for optimal performance of the recorder and for
long-term enjoyment of your CD collection, handle discs
correctly as outlined in the following guidelines.
1. Hold discs by touching only the edges or center hole.
2. When a disc is not currently being used, remove it from the
recorder and store in an appropriate case.
3. With proper disc maintenance, cleaning should not be
necessary. However, should cleaning be required, wipe by
using a clean, dry cloth. Do not wipe with a circular motion;
wipe straight outward from the center.
Do not try to clean the discs surface by using any type of disc
cleaner, record spray, antistatic spray or liquid, or any other
chemical-based liquid, because such substances might irreparably
damage the discs surface.
Do not expose discs to direct sunlight, high temperature, or high
humidity for a long period of time, because this might warp or
otherwise damage the disc.
To prevent a malfunction of this unit
Do not use any non-standard shaped CDs (heart, flower shaped,
etc.) available on the market, because they are off-balance in their
weight.
If a non-standard shaped CD is loaded into this unit, it may create
problems such as improper playback, opening the disc tray,
creating an usual noise, and this units failure.
Be sure to use a felt-tip pen or similar writing tool when writing
on the label side of the disc. Do not use a ball-point pen, pencil, or
other hard-tipped writing tool, as these may damage the disc and
may adversely affect further recording on the disc.
Do not use the discs with glue left on their surface. It may get
stuck in this unit or create damage to this unit.
When using an 8cm (3) disc, do not place a normal 12cm (5)
disc on top of it.
Do not use the discs printed with commercially available label
printers.
No!
CD/CD-R/CD-RW COMPATIBLE WITH THIS UNIT
102_HD1300(E)01-13 02.6.24, 6:51 PM4
E-5
English
GETTING STARTED
Rules of Digital Recording
SCMS—Serial Copy Management System
As a digital audio component, this unit conforms with the Serial
Copy Management System (SCMS) standards. The Serial Copy
Management System restricts copies made by recording digital
signals to first-generation copies only.
The digital program sources that have been recorded cannot be
digitally recorded again.
There are 2 rules as follows:
Rule 1
Digital sources such as commercially available CDs can be copied
digitally onto other recordable digital media with this unit (a first-
generation digital copy). However, the first-generation digital copy
cannot be copied digitally any further.
Rule 2
The source that was recorded via the ANALOG LINE IN (REC)
jacks can be copied digitally onto other recordable digital media (a
first-generation digital copy). However, the first-generation digital
copy cannot be copied digitally any further.
This unit monitors the SCMS status for each track when a digital
recording is made. If the track is protected from digital recording
and copying, it is not possible to make a digital recording and copy
of that track.
The SCMS standard does not apply to analog recording and
copying.
When making a copy from a CD onto the HDD, or from the HDD
onto a CD-R or CD-RW disc, any of the copy methods described
below can be selected. The following selections are contained in
Copy Method.
•“Auto Dig/Anlg:
Automatically switches to analog recording if the track cannot be
digitally recorded for SCMS.
•“Digital Copy:
Performs digital copying of only those tracks that can be digitally
copied.
•“Digital Move:
Performs digital copying of the tracks that cannot be digitally
copied by Digital Copy when copying from the HDD onto a
CD-R or CD-RW disc.
•“Analog Copy:
Performs analog copying regardless of the SCMS standard.
Digital Move
This unit has a built-in HDD with large space that makes a long
recording possible. You can create your own CD by editing the
various program sources that have been recorded onto the HDD of
this unit and copying them onto a CD-R or CD-RW disc.
If you want to make a digital copy of the original data that has been
created on the HDD to a CD-R or CD-RW disc, the Digital Move
method is convenient. You can make a digital copy from the HDD
onto a CD-R or CD-RW disc even if the track is protected from
making a second-generation copy by the SCMS standard.
However, since the concept of Digital Move is that the data is
moved from the HDD onto a CD-R or CD-RW disc, the original
data on the HDD is erased when moving is complete. See page 65
for details.
RULES OF DIGITAL RECORDING AND NOTES ON SYSTEM
Notes on System
Number of recordable discs and tracks and
their length
One CD-R or CD-RW disc, or one disc on the HDD can be
recorded with up to 99 tracks on them.
Once 99 tracks have been recorded, no further recording is
possible even if space for recording is available on the disc.
The minimum length of one track must be 4 seconds. If a
recording is stopped while the track is less than 4 seconds long,
this unit will record for 4 seconds, and then stop recording. The
maximum length of one track is 99 minutes 59 seconds for the
HDD.
999 discs can be created at maximum on the HDD of this unit.
However, the number of discs that can be created is limited
according to the space availability (total recordable time) on the
HDD.
The maximum length of one disc on the HDD is 99 minutes 59
seconds. However, since each track on the HDD is handled in the
unit of frame (75 frames are equal to one second), the maximum
length of one track or disc may vary slightly.
When recording on a CD-R or CD-RW disc, 2-second silence will
be automatically added to the beginning of the first track.
Therefore the actual total recordable time will be 2 seconds
shorter than the total recordable time of a CD-R or CD-RW disc.
Source sampling rate conversion
Digital input of this unit supports sampling frequencies of 32kHz,
44.1kHz, 48kHz, and 96kHz. This unit converts these inputs to
the 44.1kHz,16-bit digital signals and records them onto the
HDD, or a CD-R or CD-RW disc.
Analog input is also converted to the same digital signal to be
recorded.
This unit outputs the signals at the sampling frequency of
44.1kHz, 16-bit from its digital output.
Recording of non-audio signals
This unit is designed exclusively for recording audio signals.
Recording is only possible for audio signals.
When a CD with CD TEXT is copied onto the HDD, CD TEXT
will be automatically copied if it is not copy protected. When a
CD with CD TEXT is recorded from an external CD player, CD
TEXT cannot be copied even if it is not copy protected. To copy
CD TEXT, use the built-in CDR drive of this unit.
If the digital signals contain graphic data such as CD graphics, the
non-audio signals will not be recorded.
It is not possible to record from non-audio sources such as CD-
ROM or DVD.
Data processing
A small amount of space may be used for data processing besides
recording the actual program sources.
Although this unit is capable of recording 999 albums at
maximum onto the HDD, the data processing speed may slow
down if a large number of albums is created.
102_HD1300(E)01-13 02.6.24, 6:51 PM5
E-6
RULES OF DIGITAL RECORDING AND NOTES ON SYSTEM
Data on the HDD
The data recorded onto the built-in HDD of this unit will be numbered and organized based on the following concept:
Disc
One consequent recording is counted and numbered as one unit of
disc. The HDD of this unit can record 999 discs at maximum.
(However, the number of discs to be created may be less than 999
for the space availability on the HDD.) The maximum length of one
disc on the HDD is 99minutes 59 seconds.
Track
99 tracks can be recorded onto a disc at maximum. (However the
number of discs tracks to be recorded may be less than 99 for the
space availability on the HDD.) One track must be 4 seconds at
shortest and 99 minutes 59 seconds at longest.
Album
A group of the source programs selected from different discs and
recorded as the playlist is called album. Album corresponds to
the program function (to play back favorite tracks in the desired
order) of a standard CD player. This unit can record 999 albums at
maximum onto the HDD.
Bookmark
This unit can make a temporary bookmark on a favorite track as
playing back. The list of the program sources marked is called
bookmark. This marking is temporary and cannot be duplicated.
However, an album can be easily created by copying the
bookmarked tracks. See page 32 for details.
Group
A collection of disc(s), album(s), and a bookmark are generically
called group.
Disc 1
Track 1
Track 2
Track 3
Track 99
Disc 2
Track 1
Track 2
Track 3
Track 99
Disc 999
Track 1
Track 2
Track 3
Track 99
Disc
1
1
2
2
Track
1
2
2
3
Disc
1
2
1
999
2
Track
1
2
3
3
99
Disc Track Bookmark Album
Example of the playlist
Example of the copied tracks
with bookmarks
* The tracks are listed in the
order of copying.
102_HD1300(E)01-13 02.6.24, 6:51 PM6
E-7
English
GETTING STARTED
1 POWER
2 HDD
3 CDR
4 COPY
5 Front panel display
6 Disc tray
7 v (Open/Close)
8 TRACK NO./BOOKMARK
9 TEXT/TIME
0 COMPLETE
q MODE
w MULTI JOG knob/DIGITAL REC LEVEL control
e MENU
NAMES OF BUTTONS AND CONTROLS
Front Panel
r CLEAR
t PHONES jack
y PHONES LEVEL control
u A.M.Q.R.
i REC
o t/e (Skip/Search)
p FINALIZE
a ERASE
s r/y (Search/Skip)
d INPUT
f w/d (Play/Pause)
g ANALOG REC LEVEL control
h a (Stop)
NATURAL SOUND HDD
/
CD RECORDER
TEXT/TIME MODE
MULTI JOG
DIGITAL REC LEVEL
PUSH ENTER
TRACK NO.
FINALIZE ERASE
BOOKMARK
COMPLETE
MENU
CLEAR
MIN MAX
OPTICAL
ANALOG REC LEVEL
INPUT
REC
COAXIAL
ANALOG
COPY
A.M.Q.R.
CDRHDD
MIN MAX
LEVELPHONES
POWER
1
ty
uiopasdfgh
23 4 5 6 7890q wer
102_HD1300(E)01-13 02.6.24, 6:51 PM7
E-8
NAMES OF BUTTONS AND CONTROLS
Remote Control
OPEN/CLOSE
COPY REC
TEXT/TIME
TRACK NO.
WRITE
MODE MENU
CLEAR
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQR
7
STU
8
VWX
9
YZ
SPACE
SYMBOL
0
+
10
BOOKMARK
REPEAT RANDOM
GROUP SKIP
INTRO
ENTER
COMPLETE
A.M.Q.R.
FINALIZE
INPUT
TIMER REC
ERASE
HDD CDR
1
2
3
4
5
6
7
8
0
9
q
w
e
r
t
y
u
i
o
p
a
s
d
f
g
h
j
k
l
;
z
x
1 OPEN/CLOSE
2 COPY
3 TIMER REC
4 A.M.Q.R.
5 FINALIZE
6 TEXT/TIME
7 MODE
8 COMPLETE
9 CLEAR
0 Alphabetical/numeric buttons
q REPEAT
w RANDOM
e GROUP SKIP q
r t (Track Skip)
t d (Pause)
y e (Search)
u HDD
i REC
o ERASE
p TRACK NO. WRITE
a INPUT
s MENU
d +/
f ENTER
g BOOKMARK
h INTRO
j GROUP SKIP w
k y (Track Skip)
l r (Search)
; w (Play)
z CDR
x a (Stop)
102_HD1300(E)01-13 02.6.24, 6:51 PM8
E-9
English
GETTING STARTED
NATURAL SOUND HDD
/
CD RECORDER
TEXT/TIME MODE
MULTI JOG
DIGITAL REC LEVEL
PUSH ENTER
TRACK NO.
FINALIZE ERASE
BOOKMARK
COMPLETE
MENU
CLEAR
MIN MAX
OPTICAL
ANALOG REC LEVEL
INPUT
REC
COAXIAL
ANALOG
COPY
A.M.Q.R.
CDRHDD
MIN MAX
LEVELPHONES
POWER
30°
30°
NAMES OF BUTTONS AND CONTROLS
Loading the batteries in the remote control
1. Remove the battery compartment cover on the back
of the remote control.
2. Insert 2 batteries (AA, UM-3 or R6 type) according to
the polarity markings on the inside of the battery
compartment.
3. Close the cover until it snaps into place.
Battery replacement
If you find that the remote control must be used closer to this unit
than usual, the batteries are weak. Replace both batteries with new
ones.
Notes on batteries
Use only AA, UM-3, or R6 type batteries for replacement.
Do not mix a new battery with a used one.
A rechargeable battery cannot be used.
Do not mix different types of battery.
Do not attempt to short out the batteries by directly connecting the
plus (+) and the minus () with a piece of metal.
Remove the batteries if the remote control will not be used for an
extended period of time.
If batteries leak, dispose of them immediately. Clean the battery
compartment thoroughly before installing new batteries.
Remote control operation range
Cautions
If operation of this unit by the remote control creates any
malfunction in any other components, change the placement of
the component.
Do not spill any liquid on or drop the remote control. Do not
place it near a heater or in the bathroom where the temperature
and humidity become high.
Make sure the remote control sensor is not exposed to direct
sunlight or strong lights. If it is, it may not function correctly.
Within 6m (20)
2
1
3
Remote control sensor
102_HD1300(E)01-13 02.6.24, 6:51 PM9
E-10
NAMES OF BUTTONS AND CONTROLS
1 HDD mark
2 TOTAL indicator
3 DUPLCT indicator
4 A.M.Q.R. indicator
5 Information display
6 CDR mark
7 REC indicator
8 ALBM indicator
9 MARK indicator
0 Playback mode/play style indicator
S indicator
G indicator
A indicator
REP indicator
RNDM indicator
Display
ALBM
MARK
A.M.Q.R. AUTO PRD DIG M
REC
LEVEL
TRACK
TOC GROUP
TIME
CDR W
L
R
dB –30 –10 –6 –2 0
MULTRNDM ALL SYNC ANLG
TOTAL
DUPLCT
S G A REP
8888888888888
8 r9 0
qw
e t y
1
23 4 5
67
q Recording/copying mode indicator
AUTO indicator
PRD indicator
MULT indicator
ALL indicator
SYNC indicator
w Copying method indicator
DIG indicator
M indicator
ANLG indicator
e Level meter
r TOC indicator
t CD-RW indicator
y MULTI JOG status indicator
LEVEL indicator
TRACK indicator
GROUP indicator
TIME indicator
102_HD1300(E)01-13 02.6.24, 6:51 PM10
E-11
English
GETTING STARTED
Display while playing the data on the HDD
Group number, track number and elapsed time of the
track being played
Group number, track number and remaining time of the
track being played
Group number and group total time
Group number and group remaining time
Group title or track title
Group title
Track title
The group title with the GROUP indicator and the track title with
the TRACK indicator are switched by pressing the MULTI JOG
knob.
Display while recording onto the HDD
Disc number, track number and elapsed time of the track
being recorded
Disc number and total recorded time on the disc
NAMES OF BUTTONS AND CONTROLS
Display Information
The display located in the center of this unit provides the information about the drive (HDD or CDR drive) selected.
Each time TEXT/TIME is pressed, the display changes according to the operation.
Dsc001 1 004
GROUP
L
R
dB 30 10 6 20
G
Dsc001 1- 221
GROUP
L
R
dB 30 10 6 20
G
Dsc001 6545
GROUP
L
R
dB 30 10 6 20
TOTAL
G
Dsc001 -6240
GROUP
L
R
dB 30 10 6 20
TOTAL
G
LIVE AT CRANE
GROUP
L
R
dB 30 10 6 20
G
PRIDE AND JOY
TRACK
L
R
dB 30 10 6 20
G
Display while playing a CD
Track number and elapsed time of the track being played
Track number and remaining time of the track being
played
Disc total time
Disc remaining time
CD TEXT (when available)
Disc title
Track title
The group title with the GROUP indicator and the track title with
the TRACK indicator are switched by pressing the MULTI JOG
knob.
Display while recording onto a CD-R or CD-
RW disc
Track number and elapsed time of the track being
recorded
Total recorded time on a disc
Total recordable time on a disc
Dsc001 1 004
REC
L
R
dB 30 10 6 20
Dsc001 1543
REC
L
R
dB 30 10 6 20
TOTAL
1 004
TOC GROUP
CD
L
R
dB 30 10 6 20
1- 221
TOC GROUP
CD
L
R
dB 30 10 6 20
6545
TOC GROUP
CD
L
R
dB 30 10 6 20
TOTAL
-6240
TOC GROUP
CD
L
R
dB 30 10 6 20
TOTAL
LIVE AT CRANE
TOC GROUP
CD
L
R
dB 30 10 6 20
PRIDE AND JOY
TRACK
TOC
CD
L
R
dB 30 10 6 20
1 004
REC
GROUP
CDR W
L
R
dB 30 10 6 20
1543
REC
GROUP
CDR W
L
R
dB 30 10 6 20
TOTAL
- 221
REC
GROUP
CDR W
L
R
dB 30 10 6 20
TOTAL
102_HD1300(E)01-13 02.6.24, 6:51 PM11
E-12
NAMES OF BUTTONS AND CONTROLS
Rear Panel
LINE IN LINE OUT IN OUT
DIGITAL
REC COAXIAL OPTICAL COAXIAL OPTICAL
RS232C
VIDEO
VIDEO
OUT
S VIDEO
ANALOG
PLAY
R
L
R
L
4 3
12 3
5 64
CONNECTIONS
Turn off the power of this unit and the other components, and unplug them from the wall outlet before making any connections.
Digital connections
This unit has the DIGITAL OPTICAL jacks and DIGITAL COAXIAL jacks. Connect either the DIGITAL OPTICAL jacks, or the
DIGITAL COAXIAL jacks according to the component to be connected.
Using the optical fiber cable, connect the DIGITAL IN (OPTICAL) jack on this unit to the digital optical output jack on the other
component, and the DIGITAL OUT (OPTICAL) jack on this unit to the digital optical input jack on the other component.
When using the DIGITAL IN/OUT (COAXIAL) jacks, make connections with coaxial cables. Connect the DIGITAL IN (COAXIAL) jack
on this unit to the digital coaxial output jack on the other component, and the DIGITAL OUT (COAXIAL) jack on this unit to the digital
coaxial input jack on the other component.
Analog connections
Make sure to connect the L (left) and R (right) input and output jacks on this unit to the correct L (left) and R (right) input and output jacks
on the other component.
Connect the ANALOG LINE IN (REC) jack on this unit to the analog output jack on the other component, and the ANALOG LINE OUT
(PLAY) jack on this unit to the analog input jack on the other component.
The ANALOG LINE IN (REC)/LINE OUT (PLAY) jacks on this unit are numbered # and $ respectively. Connect these jacks to the
jacks with the same numbers when connecting this unit to a Yamaha amplifier or receiver.
To connect the turntable directly to this unit, first connect it to the phono equalizer and then connect to the ANALOG LINE IN (REC)
jacks on this unit.
Notes
When you play the data on the HDD or CDs, signals are output both from the ANALOG LINE OUT (PLAY) jack and from the DIGITAL
OUT (OPTICAL/COAXIAL) jacks.
Signals that are output through the DIGITAL OUT (OPTICAL) jacks or the DIGITAL OUT (COAXIAL) jacks while playing the data on
the HDD do not have information about the track markers. Therefore if these signals are recorded by an MD player, the track markers may
not be placed correctly on the recorded MD disc.
1 HDD slot
2 VIDEO OUT jacks
S VIDEO jack
VIDEO jack
3 AC inlet
4 ANALOG jacks
ANALOG LINE IN (REC) jacks
ANALOG LINE OUT (PLAY) jacks
5 DIGITAL jacks
DIGITAL IN (COAXIAL) jack
DIGITAL IN (OPTICAL) jack
DIGITAL OUT (COAXIAL) jack
DIGITAL OUT (OPTICAL) jack
6 RS-232C terminal
(U.S.A. model)
102_HD1300(E)01-13 02.6.24, 6:51 PM12
E-13
English
GETTING STARTED
CONNECTIONS
LINE IN LINE OUT IN OUT
DIGITAL
REC COAXIAL OPTICAL COAXIAL OPTICAL
RS232C
VIDEO
VIDEO
OUT
S VIDEO
ANALOG
PLAY
R
L
R
L
4 3
REC
PLAY
OUT
IN
DIGITAL
INPUT
COAXIAL
DIGITAL
OUTPUT
R
L
R
L
OPTICAL
OPTICAL
DIGITAL
OUTPUT
COAXIAL
VIDEO IN
S VIDEO
VIDEO
Connecting a monitor
You can display the list of groups or tracks to be played, copying/recording settings or the list of setting items on the monitor by connecting
the monitor to this unit. Connect the S VIDEO jack or the VIDEO jack whichever available on your monitor.
Use a commercially available S-video cable to connect the S VIDEO jack on this unit and the S-video input jack on the monitor.
Use an included video pin cable to connect the VIDEO jack on this unit and the composite video jack on the monitor.
Arrow marks () in the illustration below indicate the direction of the audio signal.
Coaxial cable
(optional)
To wall outlet
DVD player, cable TV tuner, etc
Monitor
S video cable
(optional)
Video pin cable
(included)
*RS-232C terminal
Optical cable
(one included)
**Coaxial cable
Amplifier or receiver
Audio pin cable
(included)
Audio pin cable
(included)
*This terminal is for connection of the personal computer. Information about the connection software is to be
announced on the YAMAHA website (see page 93).
**For U.S.A. model, one coaxial cable with ferrite core is included. Be sure to connect to the DIGITAL OUT
(COAXIAL) jack with this cable, directing the side with ferrite core to this unit.
Connecting the power cable
Plug the power cable into the AC inlet when all connections are complete, and then plug in the power cable to the wall outlet.
[Europe, U.K. and Australia models]
Plug in this unit to the wall outlet.
(U.S.A. model)
102_HD1300(E)01-13 02.6.24, 6:51 PM13
E-14
1. Turn on the power of this unit by pressing POWER on
the front panel.
The message WELCOME TO YAMAHA HDD/CD SYS-
TEM appears on the display. After the message is displayed,
this unit is ready for operation.
2. Press v (OPEN/CLOSE on the remote control) to
open the disc tray.
3. Load the CD to copy from on the disc tray.
Place a CD correctly aligned in the recessed area of the disc
tray with its label side facing up.
4. Press v (OPEN/CLOSE on the remote control) to
close the disc tray.
Note
The disc tray can be also closed by pressing the front edge of
the disc tray gently. If the disc tray is closed in this way, this
unit starts playback of a CD. Press a to stop playback.
COPYING FROM A CD ONTO THE HDD
Copying All Tracks on a CD
You can copy all tracks on a CD onto the HDD.
NATURAL SOUND HDD
/
CD RECORDER
TEXT/TIME MODE
MULTI JOG
DIGITAL REC LEVEL
PUSH ENTER
TRACK NO.
FINALIZE ERASE
BOOKMARK
COMPLETE
MENU
CLEAR
MIN MAX
OPTICAL
ANALOG REC LEVEL
INPUT
REC
COAXIAL
ANALOG
COPY
A.M.Q.R.
CDRHDD
MIN MAX
LEVELPHONES
POWER
2,4
6
3
1
5
OPEN/CLOSE
COPY REC
TEXT/TIME
TRACK NO.
WRITE
MODE MENU
CLEAR
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQR
7
STU
8
VWX
9
YZ
SPACE
SYMBOL
0 +10
BOOKMARK
REPEAT RANDOM NTRO
ENTER
COMPLETE
A.M.Q.R.
FINALIZE
INPUT
TIMER REC
ERASE
4
JKL
5
MNO
6
PQR
7
STU
8
VWX
9
YZ
SPACE
SYMBOL
0 +10
BOOKMARK
REPEAT RANDOM
GROUP SKIP
INTRO
HDD CDR
2,4
5
6
This unit starts reading the information (type and capacity of
the CD) when the CD is loaded. It takes approximately 10 to 15
seconds to complete the reading.
The following message appears on the display during the
reading.
When reading the information has been completed, the display
changes as follows, and this unit becomes ready for operation.
L
R
dB 30 10 6 20
Reading
14 6817
TOC GROUP
CD
L
R
dB 30 10 6 20
1
TOC GROUP
CD
L
R
dB 30 10 6 20
Total number of tracks Total time
103_HD1300(E)14-28 02.6.24, 6:51 PM14
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106

Yamaha CDRHD1300 Manualul proprietarului

Categorie
CD playere
Tip
Manualul proprietarului
Acest manual este potrivit și pentru