EZVIZ S5 Remote Control Manual

ACTION CAMERA

Quick Start Guide

Remote Control

UD01492B

About this Manual

The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information

hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without

notice, due to firmware updates or other reasons. Please find the latest version in the ™ website (http://www.

ezvizlife.com).

Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision

Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”). This user manual (hereinafter

referred to be “the Manual”) cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means,

without the prior written permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties,

guarantees or representations, express or implied, regarding to the Manual.

Trademarks Acknowledgement

™, ™, and other Hikvision’s trademarks and logos are the properties of Hikvision in various jurisdictions.

Other trademarks and logos mentioned below are the properties of their respective owners.

Legal Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE

AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS

OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR

PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS,

EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES,

INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA

OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF

THE POSSIBILITY OF SUCH DAMAGES. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL

HIKVISION’S TOTAL LIABILITY FOR ALL DAMAGES EXCEED THE PURCHASE PRICE THE PRODUCT.

HIKVISION does not undertake any liability for personal injury or property damage, as the result of product interruption or

service termination cause by: a) improper installation or usage other than as requested; b) the protection of national or

public interests; c) Force Majeure; d) yourself or the third party, including not limitation, using any third party’s products,

software, applications, and among others.

REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS.

HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES

RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER,

HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.

SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING

THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS TO THE APPLICABLE LAW. YOU FUTHER AGREE THAT THIS

PRODUCT IS ONLY FOR CIVIL USE, AND HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH

ILLEGITIMATE PURPOSES, SUCH AS THIRD PARTY RIGHTS INFRINGEMENT, MEDICAL TREATMENT, SAFETY

Regulatory Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired

operation.

Please take attention that changes or modification not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

Note: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in

a residential installation. This product generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body.

EU Conformity Statement

This product and - if applicable - the supplied accessories too are marked with "CE" and comply

therefore with the applicable harmonized European standards listed under the Radio Equipment

Directive 2014/53/EU, the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU.

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted

municipal waste in the European Union. For proper recycling, return this product to your local supplier

upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For

more information see: www.recyclethis.info.

EQUIPMENT OR OTHER SITUATIONS WHERE THE PRODUCT FAILURE COULD LEAD TO DEATH OR PERSONAL INJURY, OR

WEAPON OF MASS DESTRUCTION, CHEMINCAL AND BIOLOGICAL WEAPON, NUCLEAR EXPLOSION, AND ANY UNSAFE NUCLEAR

ENERGY USES OR ANTI-HUMANITY USAGES. YOU SHOULD UNDERTAKE ALL RESPONSIBILITIES FOR LOSSES OR DAMAGES

RESULTING FROM THE ABOVE USAGES WHATSOEVER.

IN THE EVENT OF ANY CONFLICTS BETWEEN THE ABOVE AND THE APPLICABLE LAW, THE LATER PREVAILS.

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two

conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence.

L'exploitation est autorisée aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en

compromettre le fonctionnement.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or

lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the

antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than

that necessary for successful communication.

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un

type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques

de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte

que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une

communication satisfaisante.

This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body.

Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et votre corps.

Safety Instruction

CAUTION: THE PRODUCT IS BUILT IN A REPLACEABLE BATTERY. RISK OF EXPLOSION IF

BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING

TO THE INSTRUCTIONS.

2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted

municipal waste in the European Union. See the product documentation for specific battery information.

The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb),

or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection

point. For more information see: www.recyclethis.info.

1

Basics

1

6

3

4

7

2

5

1Power LED Indicator Steady Red: Charging;

Steady Blue: Fully charged.

2Display Display camera status and menu.

3Switch Button Switch to the next mode or item.

4Power Button/

OK Button/

Shutter

Press to power on; Hold down to opwer off.

Confirm

Start/Stop record or capture

5Recording Status LED Indicator Red Flicker: The camera is recording.

6Return/Set Button In Main Menu: Press to enter the setting interface.

In Sub-menu: Press to return to the upper level menu.

7USB Interface Charging

The remote control vibrates when you press any button.

2

Display Introduction

1

2

3

4

5

4K |3 0

1Current Recording Mode

Video

Photo

Burst

Time Lapse

2Video Resolution|Frame Rate/ Photo Resolution/ Burst Photo

Resolution|Capture Rate/ Time Lapse Photo Resolution|Capture Interval

3Video: Time Left for Recording

Photo & Busrt & Time Lapse: Left Picture Number

4W: FOV Status

PT: Protune is on

5Camera battery

/

1H:58

3

Operation

1Charge the Remote Control

Charge the remote control with the USB cable and power adapter via the USB port. The Power

LED Indicator turning steady blue from steady red when the remote control gets fully charged.

2Power on the Remote Control

Press the button to power on the remote control. The EZVIZ logo, bluetooth connection

status and searching new camera will be displayed in turn.

FIND NEW

3Connect with the Camera

1. The remote control does not connect with any camera by default. When the remote

control startup, it starts searching the active camera nearby automatically and

displays the found camera on display.

SEARCH AGAIN

SEARCH ENDS

EZ - 123456789

SEARCHING

4

If no camera is found, the “SEARCH FAIL” will be displayed. In this case, you can

select “SEARCH AGAIN” to restart the camera and try again.

You can select “EXIT” to shut down the remote control.

2. Press to select the camera and press to connect to the camera. The

connection status appears, as shown in the following figure.

CONNECTING CONNECTING LOADING

SEARCH AGAIN

EXIT

SEARCH FAIL

The remote control enters the main menu after connected, as shown in the following figure.

4K |3 0

0H:8 8

5

If the remote control has connected to a camera before, the following prompt appears on the display

after starting up. The remote control connects to the camera automatically, and then enters the main

menu.

If your remote control cannot connect to the previously connected camera after starting up,

press the power button of the camera, and repeat the step 1 and step 2 to connect the

remote control with the camera again.

If you need to connect the remote control to another camera, press button after the remote

control starting up to switch to the "FIND NEW" item. Press button, and repeat step 1 and step

2 to connect the remote control with the new camera.

LAST CAMERA

FIND NEW

LAST CAMERA

FIND NEW

6

5Set the Camera Parameters

You can set the camera parameters as required.

In the main menu, press button until Settings icon appears, and press

to enter the Settings menu.

Operate the menu as follows:

Next OK Return to the upper level menu

4Control the Camera

In the main menu, press button to record according to the current recording mode.

Example: If the camera recording mode is set as Burst, press button to capture burst

photos.

6Shut Down the Remote Control

Hold down the to shut down the remote control.

7

Record

2. Press to record or take photo.

3. For Video mode and Time Lapse mode, press to stop recording or capturing.

1. Press to switch the recording mode to your desired one.

4K |3 0

0H:88

7M P

8888

7MP|30/1S

8888

12MP|1S

8888

Display in Video Mode Display in Photo Mode

Display in Burst Mode Display in Time Lapse Mode

8

Set Camera Parameters

You can set the camera parameters via the remote control.

The supported functions vary depending on the connected camera model.

Power on/off the Camera

If the connected camera is off, the following prompt displays.

CAMER A OF F

You can press to power on the camera.

ST AR T UP

1

Allgemeines

1

6

3

4

7

2

5

1Stromversorgungs-LED Durchgehend rot: Ladevorgang läuft

Durchgehend blau: Vollständig aufgeladen

2Anzeige Kamerastatus und Menü

3Umschalttaste Wechsel zum nächsten Modus oder Element

4Ein/Aus-Taste/

OK-Taste/

Verschluss

Zum Einschalten drücken; zum Ausschalten gedrückt halten

Bestätigen

Aufzeichnung/Erfassung starten/stoppen

5Aufnahmestatus LED-Anzeige Blinkt rot: Die Kamera zeichnet auf

6Zurück/Einstellung-Taste Im Hauptmenü: Einstellungen aufrufen

Im Untermenü: Zurück zur übergeordneten Menüebene

7USB-Schnittstelle Aufladen

Beim Betätigen einer Taste vibriert die Fernbedienung.

2

Bildschirm

1

2

3

4

5

4K |3 0

1Aktueller Aufnahmemodus

Video

Foto

Serienbild

Zeitraffer

2Videoauflösung|Bildrate / Fotoauflösung / Serienbildauflösung|Erfassungsrate /

Zeitrafferauflösung|Erfassungsintervall

3Video: Restaufnahmezeit

Foto & Serienbild & Zeitraffer: Verbleibende Bildanzahl

4W: FOV-Status

PT: Protune ein

5Kameraakku

/

1H:58

3

Bedienung

1Aufladen der Fernbedienung

Laden Sie die Fernbedienung mit dem USB-Kabel und dem Netzteil über den USB-Port

auf. Wenn die Kontroll-LED von durchgehend rot zu durchgehend blau wechselt, ist die

Fernbedienung voll aufgeladen.

2Einschalten der Fernbedienung

Drücken Sie die Taste , um die Fernbedienung einzuschalten Daraufhin werden das EZVIZ-

Logo, der aktuelle Bluetooth-Verbindungsstatus und der Kamerasuchmodus angezeigt.

FIND NEW

3Anschließen der Kamera

1. Standardmäßig ist die Fernbedienung nicht mit einer Kamera verbunden. Nach dem

Einschalten startet die Fernbedienung automatisch die Suche nach aktiven Kameras in

der Nähe und zeigt gefundene Kameras an.

SEARCH AGAIN

SEARCH ENDS

EZ - 123456789

SEARCHING

4

Sollte keine Kamera gefunden werden, wird "SEARCH FAIL" (Suche erfolglos) angezeigt.

In diesem Fall können Sie "SEARCH AGAIN" (Suche wiederholen) wählen, um die Kamera

neu zu starten und es erneut zu versuchen.

Drücken Sie auf "EXIT" (Ausschalten), um die Fernbedienung auszuschalten.

2. Drücken Sie auf , um die Kamera auszuwählen, und dann auf , um sie zu

verbinden. Der Verbindungsstatus wird angezeigt (siehe Abbildung unten).

CONNECTING CONNECTING LOADING

SEARCH AGAIN

EXIT

SEARCH FAIL

Anschließend wechselt die Fernbedienung selbstständig zum Hauptmenü (siehe Abbildung unten).

4K |3 0

0H:8 8

5

Falls die Fernbedienung bereits mit einer Kamera verbunden war, erscheint nach dem Einschalten der

folgende Hinweis. Die Fernbedienung stellt automatisch die Verbindung zur Kamera her und wechselt

dann zum Hauptmenü.

Falls die Fernbedienung nach dem Einschalten die Verbindung zur Kamera nicht wieder

herstellen kann, drücken Sie die Taste und wiederholen die Schritte 1 und 2, um beide

Geräte erneut zu verbinden.

Um die Fernbedienung mit einer anderen Kamera zu verbinden, drücken Sie nach dem Einschalten

die Taste , um zur Option "FIND NEW" (Neue suchen) zu wechseln. Drücken Sie auf und

wiederholen Sie die Schritte 1 und, um die Fernbedienung mit der neuen Kamera zu verbinden.

LAST CAMERA

FIND NEW

LAST CAMERA

FIND NEW

6

5Kameraparameter konfigurieren

Sie können die Parameter der Kamera je nach Bedarf konfigurieren.

Drücken Sie im Hauptmenü die Taste , bis das Symbol für das Einstellungsmenü

erscheint, und drücken Sie dann auf , um dieses Einstellungsmenü aufzurufen.

Die Menübedienung ist wie folgt:

Weiter OK Zurück zum übergeordneten Menü

4Kamerabedienung

Drücken Sie im Hauptmenü auf , um eine Aufnahme im aktuellen Aufnahmemodus zuma-

chen.

Beispiel: Wenn der aktuelle Aufnahmemodus der Kamera "Serienbild" ist, drücken Sie die

Taste , um Serienbilder zu speichern.

6Fernbedienung ausschalten

Drücken Sie lange auf , um die Fernbedienung auszuschalten.

7

Aufnahme

2. Drücken Sie auf , um eine Aufnahme zu starten oder ein Foto zu machen.

3. Im Videomodus und Zeitraffermodus drücken Sie auf , um den Vorgang zu beenden.

1. Drücken Sie auf , um in den gewünschten Aufnahmemodus zu wechseln.

4K |3 0

0H:88

7M P

8888

7MP|30/1S

8888

12MP|1S

8888

Anzeige im Videomodus Anzeige im Fotomodus

Anzeige im Serienbildmodus Anzeige im Zeitraffermodus

Pagina se încarcă ...

EZVIZ S5 Remote Control Manual

EZVIZ S5 Remote Control Manual

în alte limbi

Alte documente